DLINK-WLAN-MIB

All MIBs › DLINK-WLAN-MIB

Organization: D-Link, Inc.

Last Updated: 2002-08-16

Category: Domain: Wireless, Vendor: D-Link

Description: Manages wireless LAN (WLAN) configuration, radio settings, and client association on D-Link wireless devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINK-WLAN-MIB?

DLINK-WLAN-MIB is D-Link's proprietary WLAN MIB for 802.11-based wireless access points and routers, explicitly derived from the IEEE 802.11 MIB (dot11 objects), covering radio/station configuration and management operations. It exposes standard 802.11 station and radio parameters (station ID, desired SSID, BSS type, operational rate set, beacon period, DTIM period, privacy/power-management options) alongside D-Link-specific AP system controls for saving/applying configuration and rebooting. This MIB supports both configuration monitoring (SSID, security, rate settings) and software-management actions (enterpriseAPSysReboot, enterpriseAPSysConfigSave/Apply), letting an administrator confirm a config change was actually applied or trigger/verify a remote reboot of the AP. It explicitly builds on the IEEE802dot11 MIB standard, extending it with D-Link enterprise AP management objects. It is deployed on D-Link wireless access points and wireless routers in SMB/home-office wireless deployments, where a DLINK-WLAN-MIB download from D-Link's support site is typically the starting point for compiling these objects into a MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINK-WLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link wireless access point
D-Link wireless router

Monitoring Examples

An administrator would poll dot11DesiredSSID and dot11DesiredBSSType to confirm the AP is broadcasting the intended network name and mode, and check dot11BeaconPeriod/dot11DTIMPeriod against expected values if clients report slow reconnect/roaming times. Setting enterpriseAPSysConfigApply after a configuration change and then re-reading dot11OperationalRateSet confirms the change took effect without a full reboot. If configuration still fails to apply, enterpriseAPSysReboot could be invoked and dot11StationID re-checked once the AP comes back up.

What Can Be Monitored

SSID and BSS type
beacon and DTIM period
operational data rate set
power management mode
privacy option support
AP config save/apply/reboot actions

Imported Objects

From RFC1155-SMI

IpAddress
enterprises
mgmt

From RFC1213-MIB

ifIndex

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using dot11WEPICVErrorCount OID:

Select a D-Link 802.11 wireless access point/router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type dot11WEPICVErrorCount into the Find box to locate it in the OID tree, then select it and click OK. This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the value of the ICV as received in the frame does not match the ICV value that is calculated for. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
dlink	1.3.6.1.4.1.171
dlk80211bPlusDot11	1.3.6.1.4.1.171.1.3
dlkEnterpriseAP	1.3.6.1.4.1.171.1			The MIB module for D-Link 802.11 series product. This module derived from IEEE ieee802dot11
dlkEnterpriseAPlan	1.3.6.1.4.1.171.1.2
dlkEnterpriseAPsys	1.3.6.1.4.1.171.1.1
dlkEnterpriseAPTrap	1.3.6.1.4.1.171.1.4
INT dot11AccessPointMode	1.3.6.1.4.1.171.1.3.1.2.1	INTEGER	read-write	This attribute shall be a set of all the access point mode supported by the AP. The following are the default values and the associated mode. Value = 1: Normal AP Value = 2: Wireless Bridge Value = 3: Wireless AP Client Value = 4: Wireless Multi Bridge Value = 5: Backup AP Value = 6: Repeater Value = 7: Group AP
C32 dot11ACKFailureCount	1.3.6.1.4.1.171.1.3.2.2.9	Counter32	read-only	This counter shall increment when an ACK is not received when expected.
dot11APModeConfigEntry	1.3.6.1.4.1.171.1.3.1.2
INT dot11AuthenticateFailStatus	1.3.6.1.4.1.171.1.3.1.1.13	INTEGER	read-only	This attribute holds the most recently transmitted Status Code in a failed Authentication frame. If no failed Authentication frame has been transmitted, the value of this attribute shall be 0.
INT dot11AuthenticationAlgorithm	1.3.6.1.4.1.171.1.3.1.3.1	INTEGER	read-only	This attribute shall be the authentication algorithms currently used by the AP. The following are the default values and the associated algorithm. Value = 1: Open System Value = 2: Shared Key Value = 3: Both Open System and Shared Key
IP dot11BackupAPRemoteServerIPAddress	1.3.6.1.4.1.171.1.3.1.2.3	IpAddress	read-write	This attribute used to check the wired LAN connection (A.K.A. Link Integrity) when AP in Backup AP mode.
INT dot11BeaconPeriod	1.3.6.1.4.1.171.1.3.1.1.7	INTEGER	read-write	This attribute shall specify the number of TU that a station shall use for scheduling Beacon transmissions. This value is transmitted in Beacon and Probe Response frames.
INT dot11CCAModeSupported	1.3.6.1.4.1.171.1.3.4.4.3	INTEGER	read-only	dot11CCAModeSupported is a bit-significant value, representing all of the CCA modes supported by the PHY. Valid values are: energy detect only (ED_ONLY) = 01, carrier sense only (CS_ONLY) = 02, carrier sense and energy detect (ED_and_CS)= 04 or the logical sum of any of these values.
T/F dot11ChannelAgilityEnabled	1.3.6.1.4.1.171.1.3.4.1.9	TruthValue	read-only	This attribute indicates that the PHY channel agility functionality is enabled.
T/F dot11ChannelAgilityPresent	1.3.6.1.4.1.171.1.3.4.1.8	TruthValue	read-only	This attribute indicates that the PHY is capable of channel agility.
dot11CountersEntry	1.3.6.1.4.1.171.1.3.2.2
INT dot11CurrentCCAMode	1.3.6.1.4.1.171.1.3.4.4.4	INTEGER	read-only	The current CCA method in operation. Valid values are: energy detect only (edonly) = 01, carrier sense only (csonly) = 02, carrier sense and energy detect (edandcs)= 04.
INT dot11CurrentChannel	1.3.6.1.4.1.171.1.3.4.4.1	INTEGER	read-write	The current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in 15.4.6.2
I32 dot11CurrentRegDomain	1.3.6.1.4.1.171.1.3.4.1.2	Integer32	read-only	The current regulatory domain this instance of the PMD is supporting. This object corresponds to one of the RegDomains listed in dot11RegDomainsSupported.
I32 dot11CurrentRxAntenna	1.3.6.1.4.1.171.1.3.4.2.3	Integer32	read-only	The current antenna being used to receive, if the dot11 DiversitySupport indicates that diversity is not supported. The selected antenna shall be one of the antennae marked for receive in the dot11AntennasListTable.
I32 dot11CurrentTxAntenna	1.3.6.1.4.1.171.1.3.4.2.1	Integer32	read-only	The current antenna being used to transmit. This value is one of the values appearing in dot11SupportedTxAntenna. This may be used by a management agent to control which antenna is used for transmission.
INT dot11CurrentTxPowerLevel	1.3.6.1.4.1.171.1.3.4.3.10	INTEGER	read-only	The TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.
INT dot11CurrentTxRate	1.3.6.1.4.1.171.1.3.4.1.7	INTEGER	read-write	The current tx operating rate. corresponding to data rates in increments of 500Kb/s from 1 Mb/s to 63.5 Mb/s.
INT dot11DeauthenticateReason	1.3.6.1.4.1.171.1.3.1.1.11	INTEGER	read-only	This attribute holds the most recently transmitted Reason Code in a Deauthentication frame. If no Deauthentication frame has been transmitted, the value of this attribute shall be 0.
MAC dot11DeauthenticateStation	1.3.6.1.4.1.171.1.3.1.1.12	MacAddress	read-only	This attribute holds the MAC address from the Address 1 field of the most recently transmitted Deauthentication frame. If no Deauthentication frame has been transmitted, the value of this attribute shall be 0.
INT dot11DesiredBSSType	1.3.6.1.4.1.171.1.3.1.1.5	INTEGER	read-only	This attribute shall specify the type of BSS the station shall use when scanning for a BSS with which to synchronize. This value is used to filter Probe Response frames and Beacons. When set to infrastructure, the station shall only synchronize with a BSS whose Capability Information field has the ESS subfield set to 1. When set to independent, the station shall only synchronize with a BSS whose Capability Information field has the IBSS subfield set to 1. When set to any, the station may synchronize to either type of BSS.
OCT dot11DesiredSSID	1.3.6.1.4.1.171.1.3.1.1.4	OCTET STRING	read-write	This attribute reflects the Service Set ID used in the DesiredSSID parameter of the most recent MLME_Scan.request. This value may be modified by an external management entity and used by the local SME to make decisions about the Scanning process.
INT dot11DisassociateReason	1.3.6.1.4.1.171.1.3.1.1.9	INTEGER	read-only	This attribute holds the most recently transmitted Reason Code in a Disassociation frame. If no Disassociation frame has been transmitted, the value of this attribute shall be 0.
MAC dot11DisassociateStation	1.3.6.1.4.1.171.1.3.1.1.10	MacAddress	read-only	This attribute holds the MAC address from the Address 1 field of the most recently transmitted Disassociation frame. If no Disassociation frame has been transmitted, the value of this attribute shall be 0.
INT dot11DiversitySupport	1.3.6.1.4.1.171.1.3.4.2.2	INTEGER	read-only	This implementation's support for diversity, encoded as: X'01'-diversity is available and is performed over the fixed list of antennas defined in dot11DiversitySelectionRx. X'02'-diversity is not supported. X'03'-diversity is supported and control of diversity is also available, in which case the attribute dot11DiversitySelectionRx can be dynamically modified by the LME.
INT dot11DTIMPeriod	1.3.6.1.4.1.171.1.3.1.1.8	INTEGER	read-write	This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.
T/F dot11DynamicChannelEnabled	1.3.6.1.4.1.171.1.3.4.4.2	TruthValue	read-write	This attribute indicate dynamic channel is enabled.
I32 dot11EDThreshold	1.3.6.1.4.1.171.1.3.4.4.5	Integer32	read-write	The current Energy Detect Threshold being used by the DSSS PHY.
T/F dot11ExcludeUnencrypted	1.3.6.1.4.1.171.1.3.1.3.6	TruthValue	read-only	When this attribute is true, the STA shall not indicate at the MAC service interface received MSDUs that have the WEP subfield of the Frame Control field equal to zero. When this attribute is false, the STA may accept MSDUs that have the WEP subfield of the Frame Control field equal to zero. The default value of this attribute shall be false.
C32 dot11FailedCount	1.3.6.1.4.1.171.1.3.2.2.3	Counter32	read-only	This counter shall increment when an MSDU is not transmitted successfully due to the number of transmit attempts exceeding either the dot11ShortRetryLimit or dot11LongRetryLimit.
C32 dot11FCSErrorCount	1.3.6.1.4.1.171.1.3.2.2.12	Counter32	read-only	This counter shall increment when an FCS error is detected in a received MPDU.
INT dot11FragmentationThreshold	1.3.6.1.4.1.171.1.3.2.1.5	INTEGER	read-write	This attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. An MSDU or MMPDU shall be fragmented when the resulting frame has an individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.
C32 dot11FrameDuplicateCount	1.3.6.1.4.1.171.1.3.2.2.6	Counter32	read-only	This counter shall increment when a frame is received that the Sequence Control field indicates is a duplicate.
OCT dot11GroupAPID	1.3.6.1.4.1.171.1.3.1.2.4	OCTET STRING	read-write	This attribute is to identify current Group ID of the AP.
INT dot11LongRetryLimit	1.3.6.1.4.1.171.1.3.2.1.4	INTEGER	read-write	This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than dot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.
dot11mac	1.3.6.1.4.1.171.1.3.2
MAC dot11MACAddress	1.3.6.1.4.1.171.1.3.2.1.1	MacAddress	read-only	Unique MAC Address assigned to the STA.
STR dot11ManufacturerID	1.3.6.1.4.1.171.1.3.2.1.10	DisplayString	read-only	The ManufacturerID shall include, at a minimum, the name of the manufacturer. It may include additional information at the manufacturer's discretion. The default value of this attribute shall be null.
STR dot11manufacturerName	1.3.6.1.4.1.171.1.3.3.1.2.2	DisplayString	read-only	A printable string used to identify the manufacturer of the resource. Maximum string length is 128 octets. D-Link, Inc.
OCT dot11manufacturerOUI	1.3.6.1.4.1.171.1.3.3.1.2.1	OCTET STRING	read-only	Takes the value of an organizationally unique identifier. 0x00032F for D-Link, Inc.
STR dot11manufacturerProductName	1.3.6.1.4.1.171.1.3.3.1.2.3	DisplayString	read-only	A printable string used to identify the manufacturer's product name of the resource. Maximum string length is 128 octets.
STR dot11manufacturerProductVersion	1.3.6.1.4.1.171.1.3.3.1.2.4	DisplayString	read-only	Printable string used to identify the manufacturer's product version of the resource. Maximum string length is 128 octets.
INT dot11MaxReceiveLifetime	1.3.6.1.4.1.171.1.3.2.1.9	INTEGER	read-write	The MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.
INT dot11MaxTransmitMSDULifetime	1.3.6.1.4.1.171.1.3.2.1.8	INTEGER	read-write	The MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.
C32 dot11MulticastReceivedFrameCount	1.3.6.1.4.1.171.1.3.2.2.11	Counter32	read-only	This counter shall increment when a MSDU is received with the multicast bit set in the destination MAC address.
C32 dot11MulticastTransmittedFrameCount	1.3.6.1.4.1.171.1.3.2.2.2	Counter32	read-only	This counter shall increment only when the multicast bit is set in the destination MAC address of a successfully transmitted MSDU. When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs.
C32 dot11MultipleRetryCount	1.3.6.1.4.1.171.1.3.2.2.5	Counter32	read-only	This counter shall increment when an MSDU is successfully transmitted after more than one retransmission.
INT dot11NumberSupportedPowerLevels	1.3.6.1.4.1.171.1.3.4.3.1	INTEGER	read-only	The number of power levels supported by the PMD. This attribute can have a value of 1 to 8.
OCT dot11OperationalRateSet	1.3.6.1.4.1.171.1.3.1.1.6	OCTET STRING	read-write	This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the station desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3. This atribute also indicate the Basic Rate of the AP, rate that is used as transmit rate of 802.11 management and control packet. If 22Mbps is as basic rate, the bit 7(MSB) should be set(i.e. 0xAC, instead of 0x2C). Valid basic rate are (2-1)Mbps, (11-5.5-2-1)Mbps, (22-11-5.5-2-1)Mbps. example: (2-1)Mbps : 0x2C160B8482 (11-5.5-2-1)Mbps : 0x2C968B8482 (22-11-5.5-2-1)Mbps : 0xAC968B8482
dot11OperationEntry	1.3.6.1.4.1.171.1.3.2.1
INT dot11PBCCOptionImplemented	1.3.6.1.4.1.171.1.3.4.4.7	INTEGER	read-only	This attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.
dot11phy	1.3.6.1.4.1.171.1.3.4
dot11PhyAntennaEntry	1.3.6.1.4.1.171.1.3.4.2
dot11PhyDSSSEntry	1.3.6.1.4.1.171.1.3.4.4
dot11PhyOperationEntry	1.3.6.1.4.1.171.1.3.4.1
dot11PhyTxPowerEntry	1.3.6.1.4.1.171.1.3.4.3
INT dot11PHYType	1.3.6.1.4.1.171.1.3.4.1.1	INTEGER	read-only	This is an 8-bit integer value that identifies the PHY type supported by the attached PLCP and PMD. Currently defined values and their corresponding PHY types are: FHSS 2.4 GHz = 01 , DSSS 2.4 GHz = 02, IR Baseband = 03
INT dot11PowerManagementMode	1.3.6.1.4.1.171.1.3.1.1.3	INTEGER	read-only	This attribute shall specify the power management mode of the STA. When set to active, it shall indicate that the station is not in power-save mode. When set to powersave, it shall indicate that the station is in power-save mode. The power management mode is transmitted in all frames according to the rules in 7.1.3.1.7.
INT dot11PreambleType	1.3.6.1.4.1.171.1.3.2.1.7	INTEGER	read-write	This attribute indicate what preamble type is used. The default value should be Long Preamble.
dot11PrivacyEntry	1.3.6.1.4.1.171.1.3.1.3
T/F dot11PrivacyInvoked	1.3.6.1.4.1.171.1.3.1.3.2	TruthValue	read-write	When this attribute is true, it shall indicate that the IEEE 802.11 WEP mechanism is used for transmitting frames of type Data. The default value of this attribute shall be false.
T/F dot11PrivacyOptionImplemented	1.3.6.1.4.1.171.1.3.1.1.2	TruthValue	read-only	This attribute, when true, shall indicate that the IEEE 802.11 WEP option is implemented. The default value of this attribute shall be false.
STR dot11ProductID	1.3.6.1.4.1.171.1.3.2.1.11	DisplayString	read-only	The ProductID shall include, at a minimum, an identifier that is unique to the manufacturer. It may include additional information at the manufacturer's discretion. The default value of this attribute shall be null.
C32 dot11ReceivedFragmentCount	1.3.6.1.4.1.171.1.3.2.2.10	Counter32	read-only	This counter shall be incremented for each successfully received MPDU of type Data or Management.
INT dot11RegDomainsSupportValue	1.3.6.1.4.1.171.1.3.4.1.4	INTEGER	read-only	There are different operational requirements dependent on the regulatory domain. This attribute list describes the regulatory domains the PLCP and PMD support in this implementation. Currently de- fined values and their corresponding Regulatory Domains are: FCC (USA) = X'10', DOC (Canada) = X'20', ETSI (most of Europe) = X'30', Spain = X'31', France = X'32', MKK (Japan) = X'40'
MAC dot11RemoteMACAddress	1.3.6.1.4.1.171.1.3.1.2.2	MacAddress	read-write	This Remote MAC Address used by these following AP mode: Wireless Bridge, Wireless AP Client, Backup AP, Repeater. Consequently, this attribute must be set if any above mentioned mode is desired.
dot11res	1.3.6.1.4.1.171.1.3.3
dot11resAttribute	1.3.6.1.4.1.171.1.3.3.1
dot11ResourceInfoEntry	1.3.6.1.4.1.171.1.3.3.1.2
STR dot11ResourceTypeIDName	1.3.6.1.4.1.171.1.3.3.1.1	DisplayString	read-only	Contains the name of the Resource Type ID managed object. The attribute is read-write and always contains the value RTID. This attribute value shall not be used as a naming attribute for any other managed object class.
C32 dot11RetryCount	1.3.6.1.4.1.171.1.3.2.2.4	Counter32	read-only	This counter shall increment when an MSDU is successfully transmitted after one or more retransmissions.
C32 dot11RTSFailureCount	1.3.6.1.4.1.171.1.3.2.2.8	Counter32	read-only	This counter shall increment when a CTS is not received in response to an RTS.
C32 dot11RTSSuccessCount	1.3.6.1.4.1.171.1.3.2.2.7	Counter32	read-only	This counter shall increment when a CTS is received in response to an RTS.
INT dot11RTSThreshold	1.3.6.1.4.1.171.1.3.2.1.2	INTEGER	read-write	This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.
INT dot11ShortPreambleOptionImplemented	1.3.6.1.4.1.171.1.3.4.4.6	INTEGER	read-only	This attribute, when true, shall indicate that the short preamble option as deTned in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.
INT dot11ShortRetryLimit	1.3.6.1.4.1.171.1.3.2.1.3	INTEGER	read-write	This attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to dot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.
dot11smt	1.3.6.1.4.1.171.1.3.1
T/F dot11SSIDBroadcast	1.3.6.1.4.1.171.1.3.2.1.6	TruthValue	read-write	This attribute indicate whether SSID broadcast is enabled.
dot11StationConfigEntry	1.3.6.1.4.1.171.1.3.1.1
MAC dot11StationID	1.3.6.1.4.1.171.1.3.1.1.1	MacAddress	read-only	The purpose of dot11StationID is to allow a manager to identify a station for its own purposes. This attribute provides for that eventuality while keeping the true MAC address independent. Its syntax is MAC address and default value is the station's assigned, unique MAC address.
I32 dot11SupportedDataRatesRxValue	1.3.6.1.4.1.171.1.3.4.1.6	Integer32	read-only	The receive bit rates supported by the PLCP and PMD, represented by a count from X?2-X?f, corresponding to data rates in increments of 500Kb/s from 1 Mb/s to 63.5 Mb/s.
I32 dot11SupportedDataRatesTxValue	1.3.6.1.4.1.171.1.3.4.1.5	Integer32	read-only	The Transmit bit rates supported by the PLCP and PMD, represented by a count from X?2-X?f, corresponding to data rates in increments of 500Kb/s from 1 Mb/s to 63.5 Mb/s subject to limitations of each individual PHY.
INT dot11TempType	1.3.6.1.4.1.171.1.3.4.1.3	INTEGER	read-only	There are different operating temperature requirements dependent on the anticipated environmental conditions. This attribute describes the current PHY's operating temperature range capability. Currently defined values and their corresponding temperature ranges are: Type 1 = X'01'-Commercial range of 0 to 40 degrees C, Type 2 = X'02'-Industrial range of -30 to 70 degrees C.
C32 dot11TransmittedFragmentCount	1.3.6.1.4.1.171.1.3.2.2.1	Counter32	read-only	This counter shall be incremented for an acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management.
C32 dot11TransmittedFrameCount	1.3.6.1.4.1.171.1.3.2.2.13	Counter32	read-only	This counter shall increment for each successfully transmitted MSDU.
INT dot11TxPowerLevel1	1.3.6.1.4.1.171.1.3.4.3.2	INTEGER	read-only	The transmit output power for LEVEL1 in mW. This is also the default power level.
INT dot11TxPowerLevel2	1.3.6.1.4.1.171.1.3.4.3.3	INTEGER	read-only	The transmit output power for LEVEL2 in mW.
INT dot11TxPowerLevel3	1.3.6.1.4.1.171.1.3.4.3.4	INTEGER	read-only	The transmit output power for LEVEL3 in mW.
INT dot11TxPowerLevel4	1.3.6.1.4.1.171.1.3.4.3.5	INTEGER	read-only	The transmit output power for LEVEL4 in mW.
INT dot11TxPowerLevel5	1.3.6.1.4.1.171.1.3.4.3.6	INTEGER	read-only	The transmit output power for LEVEL5 in mW.
INT dot11TxPowerLevel6	1.3.6.1.4.1.171.1.3.4.3.7	INTEGER	read-only	The transmit output power for LEVEL6 in mW.
INT dot11TxPowerLevel7	1.3.6.1.4.1.171.1.3.4.3.8	INTEGER	read-only	The transmit output power for LEVEL7 in mW.
INT dot11TxPowerLevel8	1.3.6.1.4.1.171.1.3.4.3.9	INTEGER	read-only	The transmit output power for LEVEL8 in mW.
INT dot11WEPDefaultKeyID	1.3.6.1.4.1.171.1.3.1.3.3	INTEGER	read-write	This attribute shall indicate the use of the first, second, third, or fourth element of the WEPDefaultKeys array when set to values of zero, one, two, or three. The default value of this attribute shall be 0.
C32 dot11WEPExcludedCount	1.3.6.1.4.1.171.1.3.1.3.8	Counter32	read-only	This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to zero and the value of dot11ExcludeUnencrypted causes that frame to be discarded.
C32 dot11WEPICVErrorCountEx	1.3.6.1.4.1.171.1.3.1.3.7	Counter32	read-only	This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the value of the ICV as received in the frame does not match the ICV value that is calculated for the contents of the received frame.
INT dot11WEPKeyLength	1.3.6.1.4.1.171.1.3.1.3.4	INTEGER	read-write	This attribute shall indicate the length of WEP encryption length used. Value 1: 64 bit that need 5 characters of WEP Default Key Value 2: 128 bit that need 13 characters of WEP Default Key Value 3: 256 bit that need 29 characters of WEP Default Key
INT dot11WEPKeyMappingLength	1.3.6.1.4.1.171.1.3.1.3.5	INTEGER	read-only	The maximum number of tuples that dot11WEPKeyMappings can hold.
C32 dot11WEPUndecryptableCount	1.3.6.1.4.1.171.1.3.2.2.14	Counter32	read-only	This counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the WEPOn value for the key mapped to the TA's MAC address indicates that the frame should not have been encrypted or that frame is discarded due to the receiving STA not implementing the privacy option.
INT enterpriseAPSysConfigApply	1.3.6.1.4.1.171.1.1.3	INTEGER	read-write	This attribute is equivalent of setting enterpriseAPSysConfigSave then enterpriseAPSysConfigApply.
INT enterpriseAPSysConfigSave	1.3.6.1.4.1.171.1.1.1	INTEGER	read-write	User must manually SET this OID in order to save the change(s) made through SNMP to main configuration.
INT enterpriseAPSysReboot	1.3.6.1.4.1.171.1.1.2	INTEGER	read-write	This attribute is to reboot the enterprise AP system. Doesn't save the changes that had been made.

RFC description

A D-Link proprietary MIB for wireless LAN device management. Provides SNMP objects for monitoring and configuring D-Link wireless access points, adapters, and related WLAN equipment.

Start monitoring D-Link 802.11 wireless access point/router with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINK-WLAN-MIB