DES3200ME-28-L2MGMT-MIB

All MIBs › DES3200ME-28-L2MGMT-MIB

Organization: D-Link, Inc.

Last Updated: 2009-12-16

Description: Layer 2 management MIB for D-Link DES-3200ME-28 metro Ethernet switch covering STP, IGMP, loop detection, 802.1ag CFM, port security, and VLAN control

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DES3200ME-28-L2MGMT-MIB?

DES3200ME-28-L2MGMT-MIB is a D-Link private MIB defining Layer 2 network-management objects for the DES-3200ME-28 switch. It exposes front-panel LED status, system-level controls (reboot, IP/subnet/gateway configuration, management VLAN ID), and feature toggles for IGMP snooping, SNMP authentication traps, and RMON, along with a control to clear all statistics counters. As a configuration/hardware-status MIB it lets an administrator confirm core L2 features (IGMP snooping, RMON) are enabled as expected and remotely trigger a reboot or statistics reset. It is deployed on the D-Link DES-3200ME-28 managed switch. Engineers can download the DES3200ME-28-L2MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DES3200ME-28-L2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link DES-3200ME-28 managed switch

Monitoring Examples

An administrator checks swL2DevCtrlIGMPSnooping on the DES-3200ME-28 switch to confirm multicast snooping is enabled before troubleshooting a multicast-flooding complaint on that switch.

What Can Be Monitored

IGMP snooping/RMON/SNMP-trap feature state
front-panel LED status

Imported Objects

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

From SWPRIMGMT-DES3200-MIB

dlink-des3200me-28Prod

OIDs

OID symbolic	OID numeric	Type	Access	Description
swL2MgmtMIB	1.3.6.1.4.1.171.10.113.1.6.2			The Structure of Layer 2 Network Management Information for enterprise.
swL2DevMgmt	1.3.6.1.4.1.171.10.113.1.6.2.1
swL2DevInfo	1.3.6.1.4.1.171.10.113.1.6.2.1.1
OCT swL2DevInfoFrontPanelLedStatus	1.3.6.1.4.1.171.10.113.1.6.2.1.1.5	OCTET STRING	read-only	This object is a set of system LED indicators. The first two octets are defined as the system LED. The first indicator is the power LED. The second indicator is the console LED. The other octets are defined as follow: Starting on the third octet indicates the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presented to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED: The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED: 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
swL2DevCtrl	1.3.6.1.4.1.171.10.113.1.6.2.1.2
INT swL2DevCtrlSystemReboot	1.3.6.1.4.1.171.10.113.1.6.2.1.2.1	INTEGER	read-write	This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.
IP swL2DevCtrlSystemIP	1.3.6.1.4.1.171.10.113.1.6.2.1.2.2	IpAddress	read-write	This object indicates system IP.
IP swL2DevCtrlSubnetMask	1.3.6.1.4.1.171.10.113.1.6.2.1.2.3	IpAddress	read-write	This object indicates system subnet mask.
IP swL2DevCtrlDefaultGateway	1.3.6.1.4.1.171.10.113.1.6.2.1.2.4	IpAddress	read-write	This object indicates system default gateway.
VLA swL2DevCtrlManagementVlanId	1.3.6.1.4.1.171.10.113.1.6.2.1.2.5	VlanId	read-write	This object controls the VLAN, including system IP. The VLAN should have been created.
INT swL2DevCtrlIGMPSnooping	1.3.6.1.4.1.171.10.113.1.6.2.1.2.7	INTEGER	read-write	This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .
INT swL2DevCtrlCleanAllStatisticCounter	1.3.6.1.4.1.171.10.113.1.6.2.1.2.12	INTEGER	read-write	As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
INT swL2DevCtrlSnmpEnableAuthenTraps	1.3.6.1.4.1.171.10.113.1.6.2.1.2.13	INTEGER	read-write	Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system.
INT swL2DevCtrlRmonState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.16	INTEGER	read-write	This object can be enabled or disabled RMON.
INT swL2DevCtrlIpAutoConfig	1.3.6.1.4.1.171.10.113.1.6.2.1.2.17	INTEGER	read-write	Indicates the status of automatically getting configuration from TFTP server on device
INT swL2MACNotifyState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.19	INTEGER	read-write	This object can enabled or disabled MAC Notification.
INT swL2MACNotifyHistorySize	1.3.6.1.4.1.171.10.113.1.6.2.1.2.20	INTEGER	read-write	This object indicates the history size of variation MAC in address table. The default value is 1 .
INT swL2MACNotifyInterval	1.3.6.1.4.1.171.10.113.1.6.2.1.2.21	INTEGER	read-write	This object indicates the time interval in second for trigger the MAC notify message.
INT swL2DevCtrlLLDPState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.22	INTEGER	read-write	Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
INT swL2DevCtrlLLDPForwardMessageState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.23	INTEGER	read-write	When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Units packet will be forwarded.
INT swL2DevCtrlAsymVlanState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.24	INTEGER	read-write	This object enables or disables the asymmetric VLAN feature of the device.
INT swL2IGMPSnoopingMulticastVlanState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.25	INTEGER	read-write	This indicates the global state of the igmp_snoop multicast_vlan.
INT swL2DevCtrlVLANTrunkState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.26	INTEGER	read-write	This indicates the global state of the VLAN trunking feature of the device.
INT swL2DevArpAgingTime	1.3.6.1.4.1.171.10.113.1.6.2.1.2.27	INTEGER	read-write	The timeout period in minutes for aging out dynamically learned ARP information.
INT swL2DevPasswordEncryptionState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.28	INTEGER	read-write	If the password encryption is enabled, the password will be in encrypted form.
swL2DevCtrlCFM	1.3.6.1.4.1.171.10.113.1.6.2.1.2.29
INT swL2DevCtrlCFMState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.29.1	INTEGER	read-write	This object indicates the CFM global state.
swL2DevCtrlCFMPortTable	1.3.6.1.4.1.171.10.113.1.6.2.1.2.29.2		not-accessible	A table containing the CFM state of specified ports.
swL2DevCtrlCFMPortEntry	1.3.6.1.4.1.171.10.113.1.6.2.1.2.29.2.1		not-accessible	The entry of the CFM state on specified ports.
INT swL2DevCtrlCFMPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.1.2.29.2.1.1	INTEGER	not-accessible	This object indicates the port number.
INT swL2DevCtrlCFMPortState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.29.2.1.2	INTEGER	read-write	This object indicates the CFM state by port.
swL2DevCtrlWeb	1.3.6.1.4.1.171.10.113.1.6.2.1.2.30
INT swL2DevCtrlWebState	1.3.6.1.4.1.171.10.113.1.6.2.1.2.30.1	INTEGER	read-write	This object controls Web status.
swL2DevAlarm	1.3.6.1.4.1.171.10.113.1.6.2.1.3
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.171.10.113.1.6.2.1.3.3	INTEGER	read-write	This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state.
swL2PortMgmt	1.3.6.1.4.1.171.10.113.1.6.2.2
swL2PortInfoTable	1.3.6.1.4.1.171.10.113.1.6.2.2.1		not-accessible	A table that contains information about every port.
swL2PortInfoEntry	1.3.6.1.4.1.171.10.113.1.6.2.2.1.1		not-accessible	A list of information for each port of the device.
INT swL2PortInfoPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.2.1.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortInfoMediumType	1.3.6.1.4.1.171.10.113.1.6.2.2.1.1.2	INTEGER	read-only	This object indicates the port type: fiber or copper.
INT swL2PortInfoLinkStatus	1.3.6.1.4.1.171.10.113.1.6.2.2.1.1.4	INTEGER	read-only	This object indicates the port link status.
INT swL2PortInfoNwayStatus	1.3.6.1.4.1.171.10.113.1.6.2.2.1.1.5	INTEGER	read-only	This object indicates the port speed and duplex mode.
INT swL2PortInfoFlowCtrlOperStatus	1.3.6.1.4.1.171.10.113.1.6.2.2.1.1.10	INTEGER	read-only	The current operational state of flow control. The none (1) state indicates that no flow control is performed. The flow control mechanism is different between full duplex mode and half duplex mode. For full duplex mode, the IEEE 802.3x (2) flow control function sends PAUSE frames and receives PAUSE frames. For half duplex mode, backpressure (3) is performed.
swL2PortCtrlTable	1.3.6.1.4.1.171.10.113.1.6.2.2.2		not-accessible	A table that contains control information about every port.
swL2PortCtrlEntry	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1		not-accessible	A list of control information for each port of the device.
INT swL2PortCtrlPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortCtrlPortMediumType	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.2	INTEGER	read-only	This object indicates the port type: fiber or copper.
INT swL2PortCtrlAdminState	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.3	INTEGER	read-write	This object decides whether the port is enabled or disabled.
INT swL2PortCtrlNwayState	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.4	INTEGER	read-write	Choose the port speed, duplex mode, and N-Way function mode.
INT swL2PortCtrlFlowCtrlState	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.5	INTEGER	read-write	Set the flow control function as enabled or disabled.
STR swL2PortCtrlDescription	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.6	DisplayString	read-write	The object describes the ports in text.
INT swL2PortCtrlAddressLearning	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.7	INTEGER	read-write	This object decides whether the address learning is enabled or disabled.
INT swL2PortCtrlMACNotifyState	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.8	INTEGER	read-write	This object sets each port's MAC notification state.
INT swL2PortCtrlMulticastfilter	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.9	INTEGER	read-write	This object decides the multicast packet filtering mode on this port.
INT swL2PortCtrlMDIXState	1.3.6.1.4.1.171.10.113.1.6.2.2.2.1.10	INTEGER	read-write	This object configures the MDIX setting of the port. The value 'other' is for those entries in which MDIX is not applicable.
swL2PortErrTable	1.3.6.1.4.1.171.10.113.1.6.2.2.3		not-accessible	A table that contains information about the Err port.
swL2PortErrEntry	1.3.6.1.4.1.171.10.113.1.6.2.2.3.1		not-accessible	A list of information for the err port of the device.
INT swL2PortErrPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.2.3.1.1	INTEGER	read-only	This object indicates the module's port number.(1..Max port number in the module)
INT swL2PortErrPortState	1.3.6.1.4.1.171.10.113.1.6.2.2.3.1.2	INTEGER	read-only	This object decides whether the port state is enabled or disabled.
INT swL2PortErrPortStatus	1.3.6.1.4.1.171.10.113.1.6.2.2.3.1.3	INTEGER	read-only	This object decides whether the PortStatus is err-disabled.
INT swL2PortErrPortReason	1.3.6.1.4.1.171.10.113.1.6.2.2.3.1.4	INTEGER	read-only	This object decides whether the PortStatus STP is LBD or Storm control.
STR swL2PortErrDescription	1.3.6.1.4.1.171.10.113.1.6.2.2.3.1.5	DisplayString	read-only	The object describes the ports in text.
INT swL2PortCtrlJumboFrame	1.3.6.1.4.1.171.10.113.1.6.2.2.4	INTEGER	read-write	This object configures the switch's jumbo frame settings.
INT swL2PortCtrlJumboFrameMaxSize	1.3.6.1.4.1.171.10.113.1.6.2.2.5	INTEGER	read-only	This object describes how many bytes the max jumbo frame is.
swL2QOSMgmt	1.3.6.1.4.1.171.10.113.1.6.2.3
swL2QOSBandwidthControlTable	1.3.6.1.4.1.171.10.113.1.6.2.3.1		not-accessible	.
swL2QOSBandwidthControlEntry	1.3.6.1.4.1.171.10.113.1.6.2.3.1.1		not-accessible	A list of information contained in swL2QOSBandwidthControlTable.
INT swL2QOSBandwidthPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.3.1.1.1	INTEGER	read-only	Indicates the port.
INT swL2QOSBandwidthRxRate	1.3.6.1.4.1.171.10.113.1.6.2.3.1.1.2	INTEGER	read-write	Indicates the RX Rate(Kbit/sec) of the specified port. A value of 1024000 means no limit.
INT swL2QOSBandwidthTxRate	1.3.6.1.4.1.171.10.113.1.6.2.3.1.1.3	INTEGER	read-write	Indicates the TX Rate(Kbit/sec) of the specified port. A value of 1024000 means no limit.
INT swL2QOSBandwidthRadiusRxRate	1.3.6.1.4.1.171.10.113.1.6.2.3.1.1.4	INTEGER	read-only	The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
INT swL2QOSBandwidthRadiusTxRate	1.3.6.1.4.1.171.10.113.1.6.2.3.1.1.5	INTEGER	read-only	The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
swL2QOSSchedulingTable	1.3.6.1.4.1.171.10.113.1.6.2.3.2		not-accessible	.
swL2QOSSchedulingEntry	1.3.6.1.4.1.171.10.113.1.6.2.3.2.1		not-accessible	A list of information contained in the swL2QOSSchedulingTable.
INT swL2QOSSchedulingClassIndex	1.3.6.1.4.1.171.10.113.1.6.2.3.2.1.1	INTEGER	read-only	Indicates the hardware queue number.
INT swL2QOSSchedulingMaxWeight	1.3.6.1.4.1.171.10.113.1.6.2.3.2.1.4	INTEGER	read-write	Indicates the maximum number of packets the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets.
INT swL2QOSSchedulingMechanism	1.3.6.1.4.1.171.10.113.1.6.2.3.2.1.5	INTEGER	read-only	Indicates the mechanism of QOS scheduling.
swL2QOS8021pUserPriorityTable	1.3.6.1.4.1.171.10.113.1.6.2.3.3		not-accessible	.
swL2QOS8021pUserPriorityEntry	1.3.6.1.4.1.171.10.113.1.6.2.3.3.1		not-accessible	A list of information contained in the swL2QOS8021pUserPriorityTable.
INT swL2QOS8021pUserPriorityIndex	1.3.6.1.4.1.171.10.113.1.6.2.3.3.1.1	INTEGER	read-only	The 802.1p user priority.
INT swL2QOS8021pUserPriorityClass	1.3.6.1.4.1.171.10.113.1.6.2.3.3.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
swL2QOS8021pDefaultPriorityTable	1.3.6.1.4.1.171.10.113.1.6.2.3.4		not-accessible	.
swL2QOS8021pDefaultPriorityEntry	1.3.6.1.4.1.171.10.113.1.6.2.3.4.1		not-accessible	A list of information contained in the swL2QOS8021pDefaultPriorityTable.
INT swL2QOS8021pDefaultPriorityIndex	1.3.6.1.4.1.171.10.113.1.6.2.3.4.1.1	INTEGER	read-only	Indicates the port number.
INT swL2QOS8021pDefaultPriority	1.3.6.1.4.1.171.10.113.1.6.2.3.4.1.2	INTEGER	read-write	The priority value to assign to untagged packets received by the switch ports on the switch.
INT swL2QOS8021pRadiusPriority	1.3.6.1.4.1.171.10.113.1.6.2.3.4.1.3	INTEGER	read-only	Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
INT swL2QOSSchedulingMechanismCtrl	1.3.6.1.4.1.171.10.113.1.6.2.3.5	INTEGER	read-write	This object can control QOS scheduling Mechanism.
swL2TrunkMgmt	1.3.6.1.4.1.171.10.113.1.6.2.4
I32 swPortTrunkMaxEntries	1.3.6.1.4.1.171.10.113.1.6.2.4.1	Integer32	read-only	The max entries of the swPortTrunkTable
I32 swPortTrunkMaxPortMembers	1.3.6.1.4.1.171.10.113.1.6.2.4.2	Integer32	read-only	The max number of ports allowed in a trunk.
swPortTrunkTable	1.3.6.1.4.1.171.10.113.1.6.2.4.3		not-accessible	This table specifies the port membership for each logical link.
swPortTrunkEntry	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1		not-accessible	A list of information that specifies which port group forms a single logical link.
I32 swPortTrunkIndex	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.1	Integer32	read-only	The index of logical port trunk.
I32 swPortTrunkMasterPort	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.2	Integer32	read-create	The object indicates the master port number of the port trunk entry. The first port of the trunk is implicitly configured to be the master logical port. When using a Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
POR swPortTrunkPortList	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.3	PortList	read-create	Indicate member ports of a logical trunk.
INT swPortTrunkType	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.4	INTEGER	read-create	This object indicates the type of this entry.
POR swPortTrunkActivePort	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.5	PortList	read-only	This object indicates the active ports of this entry.
ROW swPortTrunkState	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.6	RowStatus	read-create	This object indicates the status of this entry. when the state is CreatAndGo (4),the type of trunk is static (1); when the state is CreatAndWait (5), the type of trunk is lacp(2).
I32 swPortTrunkFloodingPort	1.3.6.1.4.1.171.10.113.1.6.2.4.3.1.7	Integer32	read-only	The flooding port of every trunk.
INT swL2TrunkAlgorithm	1.3.6.1.4.1.171.10.113.1.6.2.4.4	INTEGER	read-write	This object configures part of the packet to be examined by the switch when selecting the egress port for transmitting load-sharing data.
swL2TrunkLACPPortTable	1.3.6.1.4.1.171.10.113.1.6.2.4.5		not-accessible	This table specifies which port group a set of ports (up to 8) is formed into a single logical link.
swL2TrunkLACPPortEntry	1.3.6.1.4.1.171.10.113.1.6.2.4.5.1		not-accessible	A list of information specifies which port group a set of ports (up to 8) is formed into a single logical link.
INT swL2TrunkLACPPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.4.5.1.1	INTEGER	read-only	The index of the logical port LACP.
INT swL2TrunkLACPPortState	1.3.6.1.4.1.171.10.113.1.6.2.4.5.1.2	INTEGER	read-write	The state of the logical port LACP.
swL2TrunkVLANTable	1.3.6.1.4.1.171.10.113.1.6.2.4.6		not-accessible	This table is used to manage the VLAN trunking feature of the device.
swL2TrunkVLANEntry	1.3.6.1.4.1.171.10.113.1.6.2.4.6.1		not-accessible	This object is used to configure the VLAN trunking settings for each port.
INT swL2TrunkVLANPort	1.3.6.1.4.1.171.10.113.1.6.2.4.6.1.1	INTEGER	read-only	This object indicates the port being configured.
INT swL2TrunkVLANState	1.3.6.1.4.1.171.10.113.1.6.2.4.6.1.2	INTEGER	read-write	The state of the logical port LACP.
swPortMirrorPackage	1.3.6.1.4.1.171.10.113.1.6.2.6
POR swPortMirrorRxPortList	1.3.6.1.4.1.171.10.113.1.6.2.6.2	PortList	read-write	This object indicates the Rx port list of ports to be sniffed.
POR swPortMirrorTxPortList	1.3.6.1.4.1.171.10.113.1.6.2.6.3	PortList	read-write	This object indicates the Tx port list of ports to be sniffed.
I32 swPortMirrorTargetPort	1.3.6.1.4.1.171.10.113.1.6.2.6.4	Integer32	read-write	This object indicates the switch whose port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
INT swPortMirrorState	1.3.6.1.4.1.171.10.113.1.6.2.6.5	INTEGER	read-write	This object indicates the status of this entry.
swIGMPPackage	1.3.6.1.4.1.171.10.113.1.6.2.7
INT swL2IGMPMaxSupportedVlans	1.3.6.1.4.1.171.10.113.1.6.2.7.1	INTEGER	read-only	The maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPMaxIpGroupNumPerVlan	1.3.6.1.4.1.171.10.113.1.6.2.7.2	INTEGER	read-only	The maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
swL2IGMPCtrlTable	1.3.6.1.4.1.171.10.113.1.6.2.7.3		not-accessible	The table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN mode is disabled, there is only one entry in the table, with index 1. If VLAN is in Port-Based or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
swL2IGMPCtrlEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1		not-accessible	An entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP captures the switch (swL2DevCtrlIGMPSnooping) is enabled.
INT swL2IGMPCtrlVid	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.1	INTEGER	read-only	This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Based mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by management user, and the VID in each entry must be unique in the IGMP Control Table.
INT swL2IGMPQueryInterval	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.2	INTEGER	read-write	The frequency at which IGMP Host-Query packets are transmitted on this switch.
INT swL2IGMPMaxResponseTime	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.3	INTEGER	read-write	The maximum query response time on this switch.
INT swL2IGMPRobustness	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.4	INTEGER	read-write	The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
INT swL2IGMPLastMemberQueryInterval	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.5	INTEGER	read-write	The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
INT swL2IGMPQueryState	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.9	INTEGER	read-write	This object decides if the IGMP query is enabled or disabled.
INT swL2IGMPCurrentState	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.10	INTEGER	read-only	This object indicates the current IGMP query state.
INT swL2IGMPCtrlState	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.11	INTEGER	read-write	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable (2) - IGMP function is disabled for this entry. enable (3) - IGMP function is enabled for this entry.
INT swL2IGMPFastLeave	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.12	INTEGER	read-write
INT swL2IGMPDynIPMultVlanAge	1.3.6.1.4.1.171.10.113.1.6.2.7.3.1.14	INTEGER	read-write	This object is used to enable or disable aging on the dynamic IP multicast entry in this VLAN.
swL2IGMPQueryInfoTable	1.3.6.1.4.1.171.10.113.1.6.2.7.4		not-accessible	The table contains the number of current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.
swL2IGMPQueryInfoEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.4.1		not-accessible	Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
INT swL2IGMPInfoVid	1.3.6.1.4.1.171.10.113.1.6.2.7.4.1.1	INTEGER	read-only	This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
INT swL2IGMPInfoQueryCount	1.3.6.1.4.1.171.10.113.1.6.2.7.4.1.2	INTEGER	read-only	This object indicates the number of query packets received since the IGMP function enabled, on a per-VLAN basis.
INT swL2IGMPInfoTxQueryCount	1.3.6.1.4.1.171.10.113.1.6.2.7.4.1.3	INTEGER	read-only	This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiring, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
swL2IGMPRouterPortTable	1.3.6.1.4.1.171.10.113.1.6.2.7.6		not-accessible	The information of the router port table.
swL2IGMPRouterPortEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.6.1		not-accessible	The entry of the swL2IGMPRouterPortTable.
INT swL2IGMPRouterPortVlanid	1.3.6.1.4.1.171.10.113.1.6.2.7.6.1.1	INTEGER	read-only	This object indicates the VLAN ID of the router port entry.
STR swL2IGMPRouterPortVlanName	1.3.6.1.4.1.171.10.113.1.6.2.7.6.1.2	SnmpAdminString	read-only	This object indicates the VLAN name of the router port entry.
POR swL2IGMPRouterPortStaticPortList	1.3.6.1.4.1.171.10.113.1.6.2.7.6.1.3	PortList	read-write	This object indicates the static portlist of the router port entry.
POR swL2IGMPRouterPortDynamicPortList	1.3.6.1.4.1.171.10.113.1.6.2.7.6.1.4	PortList	read-only	This object indicates the dynamic portlist of the router port entry.
POR swL2IGMPRouterPortForbiddenPortList	1.3.6.1.4.1.171.10.113.1.6.2.7.6.1.5	PortList	read-write	This object indicates the forbidden portlist of the router port entry.
swL2IGMPAccessAuthTable	1.3.6.1.4.1.171.10.113.1.6.2.7.7		not-accessible	This table is used to manage the IGMP Access Authentication configurations of the device.
swL2IGMPAccessAuthEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.7.1		not-accessible	A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
INT swL2IGMPAccessAuthPort	1.3.6.1.4.1.171.10.113.1.6.2.7.7.1.1	INTEGER	read-only	The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
INT swL2IGMPAccessAuthState	1.3.6.1.4.1.171.10.113.1.6.2.7.7.1.2	INTEGER	read-write	This object denotes the status of IGMP Access Authentication of the port.
swL2IGMPMulticastVlanTable	1.3.6.1.4.1.171.10.113.1.6.2.7.8		not-accessible	Information about the IGMP snooping multicast VLAN table.
swL2IGMPMulticastVlanEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1		not-accessible	The entry of swL2IGMPMulticastVlanTable.
INT swL2IGMPMulticastVlanid	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.1	INTEGER	read-only	This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
STR swL2IGMPMulticastVlanName	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.2	DisplayString	read-create	This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
POR swL2IGMPMulticastVlanSourcePort	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.3	PortList	read-write	This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
POR swL2IGMPMulticastVlanMemberPort	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.4	PortList	read-write	This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The member ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
POR swL2IGMPMulticastVlanTagMemberPort	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.5	PortList	read-write	This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.
INT swL2IGMPMulticastVlanState	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.6	INTEGER	read-write	This object can be used to enable or disable the IGMP snooping multicast VLAN.
IP swL2IGMPMulticastVlanReplaceSourceIp	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.7	IpAddress	read-write	The replacement source IP of this multicast VLAN.
ROW swL2IGMPMulticastVlanRowStatus	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.8	RowStatus	read-create	This object indicates the status of this entry.
POR swL2IGMPMulticastVlanUntagSourcePort	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.9	PortList	read-create	This object indicates the port list of the untag source ports of the IGMP snooping multicast VLAN.
INT swL2IGMPMulticastVlanRemapPriority	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.10	INTEGER	read-create	This is the priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to -1, the packet's original priority will be used.
INT swL2IGMPMulticastVlanReplacePriority	1.3.6.1.4.1.171.10.113.1.6.2.7.8.1.11	INTEGER	read-create	This specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set.
swL2IGMPMulticastVlanGroupTable	1.3.6.1.4.1.171.10.113.1.6.2.7.9		not-accessible	The table containing the IGMP snooping multicast VLAN group information
swL2IGMPMulticastVlanGroupEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.9.1		not-accessible	Information about the current IGMP snooping multicast VLAN group.
INT swL2IGMPMulticastVlanGroupVid	1.3.6.1.4.1.171.10.113.1.6.2.7.9.1.1	INTEGER	read-only	This object indicates the VID of the IGMP snooping multicast VLAN group.
IP swL2IGMPMulticastVlanGroupFromIp	1.3.6.1.4.1.171.10.113.1.6.2.7.9.1.2	IpAddress	read-only	Specifies the multicast address list for this VLAN.
IP swL2IGMPMulticastVlanGroupToIp	1.3.6.1.4.1.171.10.113.1.6.2.7.9.1.3	IpAddress	read-only	Specifies the multicast address list for this VLAN.
ROW swL2IGMPMulticastVlanGroupStatus	1.3.6.1.4.1.171.10.113.1.6.2.7.9.1.4	RowStatus	read-create	This object indicates the status of this entry.
swL2IGMPDynIpMultMgmt	1.3.6.1.4.1.171.10.113.1.6.2.7.12
INT swL2IGMPDynIPMultMaxEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.12.1	INTEGER	read-write	This object specifies the maximum number of entries which can be learned by dynamic IP multicast.
swL2IGMPSnoopingClearDynIpMult	1.3.6.1.4.1.171.10.113.1.6.2.7.12.2
VLA swL2IGMPSnoopingClearDynIpMultVID	1.3.6.1.4.1.171.10.113.1.6.2.7.12.2.1	VlanId	read-write	This object indicates the VLAN identifier where the data driven entries will be removed from.
IP swL2IGMPSnoopingClearDynIpMultIP	1.3.6.1.4.1.171.10.113.1.6.2.7.12.2.2	IpAddress	read-write	This object indicates the IP address of the IGMP snooping group from which the data driven entries will be removed.
INT swL2IGMPSnoopingClearDynIpMultAction	1.3.6.1.4.1.171.10.113.1.6.2.7.12.2.3	INTEGER	read-write	Setting this object will clear the data driven entries. all - Remove all learned data driven groups. VLAN - Clear all data driven entries in the VLAN specified in swIGMPSnoopingClearDynIpMultVID. group - Clear the group with the address specified in swL2IGMPSnoopingClearDynIpMultIP in the VLAN specified in swIGMPSnoopingClearDynIpMultVID.
swIGMPSnoopingHostTable	1.3.6.1.4.1.171.10.113.1.6.2.7.13		not-accessible	The table contains the IGMP hosts that have joined the groups.
swIGMPSnoopingHostEntry	1.3.6.1.4.1.171.10.113.1.6.2.7.13.1		not-accessible	The entry contains the IGMP host that has joined the group.
VLA swIGMPSnoopingHostVid	1.3.6.1.4.1.171.10.113.1.6.2.7.13.1.1	VlanId	read-only	This object indicates the VID of the individual IGMP snooping host table entry.
IP swIGMPSnoopingHostGroup	1.3.6.1.4.1.171.10.113.1.6.2.7.13.1.2	IpAddress	read-only	This object indicates the group address of the individual IGMP snooping host table entry.
INT swIGMPSnoopingHostPort	1.3.6.1.4.1.171.10.113.1.6.2.7.13.1.3	INTEGER	read-only	This object indicates the port number of the individual IGMP snooping host table entry.
IP swIGMPSnoopingHostIp	1.3.6.1.4.1.171.10.113.1.6.2.7.13.1.4	IpAddress	read-only	This object indicates the host IP address of the individual IGMP snooping host table entry.
swL2TrafficSegMgmt	1.3.6.1.4.1.171.10.113.1.6.2.12
swL2TrafficSegTable	1.3.6.1.4.1.171.10.113.1.6.2.12.1		not-accessible	This table specifies the port just can forward traffic to the specific port list.
swL2TrafficSegEntry	1.3.6.1.4.1.171.10.113.1.6.2.12.1.1		not-accessible	A list of information specifies the port with its traffic forward list.
INT swL2TrafficSegPort	1.3.6.1.4.1.171.10.113.1.6.2.12.1.1.1	INTEGER	read-only	The port number of the logical port.
POR swL2TrafficSegForwardPorts	1.3.6.1.4.1.171.10.113.1.6.2.12.1.1.2	PortList	read-write	The port list that the specific port can forward traffic.
swL2PortSecurityMgmt	1.3.6.1.4.1.171.10.113.1.6.2.15
swL2PortSecurityControlTable	1.3.6.1.4.1.171.10.113.1.6.2.15.1		not-accessible	The port security feature controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as a static entry. When the learned address number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
swL2PortSecurityControlEntry	1.3.6.1.4.1.171.10.113.1.6.2.15.1.1		not-accessible	A list of information contained in the swL2PortSecurityControlTable.
INT swL2PortSecurityPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.15.1.1.1	INTEGER	read-only	Indicates a secured port to lock address learning.
INT swL2PortSecurityMaxLernAddr	1.3.6.1.4.1.171.10.113.1.6.2.15.1.1.2	INTEGER	read-write	Indicates the allowable number of addresses to be learned at this port.
INT swL2PortSecurityMode	1.3.6.1.4.1.171.10.113.1.6.2.15.1.1.3	INTEGER	read-write	Indicates the mode of locking address. In deleteOnTimeout (3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset (4) mode - never age out the locked addresses unless restarting the system to prevent port movement or intrusion.
INT swL2PortSecurityAdmState	1.3.6.1.4.1.171.10.113.1.6.2.15.1.1.4	INTEGER	read-write	Indicates an administration state of locking address.
INT swL2PortSecurityEntryClearCtrl	1.3.6.1.4.1.171.10.113.1.6.2.15.1.1.5	INTEGER	read-write	Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.
INT swL2PortSecurityTrapLogState	1.3.6.1.4.1.171.10.113.1.6.2.15.2	INTEGER	read-write	When enabled (2), whenever there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out and the relevant information will be logged in the system.
swL2PortSecurityDelCtrl	1.3.6.1.4.1.171.10.113.1.6.2.15.3
STR swL2PortSecurityDelVlanName	1.3.6.1.4.1.171.10.113.1.6.2.15.3.1	DisplayString	read-write	Indicates the VLAN name.
INT swL2PortSecurityDelPort	1.3.6.1.4.1.171.10.113.1.6.2.15.3.2	INTEGER	read-write	Indicates the port. 0 means the function dose not work now.
MAC swL2PortSecurityDelMacAddress	1.3.6.1.4.1.171.10.113.1.6.2.15.3.3	MacAddress	read-write	Specifies the MAC address.
INT swL2PortSecurityDelActivity	1.3.6.1.4.1.171.10.113.1.6.2.15.3.4	INTEGER	read-write
swL2CosMgmt	1.3.6.1.4.1.171.10.113.1.6.2.17
swL2CosPriorityCtrl	1.3.6.1.4.1.171.10.113.1.6.2.17.3
swL2CosPriorityTable	1.3.6.1.4.1.171.10.113.1.6.2.17.3.1		not-accessible	Used to show and configure per port priority-based QoS features on the switch.
swL2CosPriorityEntry	1.3.6.1.4.1.171.10.113.1.6.2.17.3.1.1		not-accessible	A list of information contained in the swL2CosPriorityTable.
INT swL2CosPriorityPort	1.3.6.1.4.1.171.10.113.1.6.2.17.3.1.1.1	INTEGER	read-only	The port number of CoS Priority.
INT swL2CosPriorityEtherPRI	1.3.6.1.4.1.171.10.113.1.6.2.17.3.1.1.3	INTEGER	read-write	Enable Ethernet frame based priority. When set ether8021p (2), enable 802.1p QoS; When set macBase (3), enable MAC-based QoS; When set disable (1), disable Ethernet frame based priority.
INT swL2CosPriorityIpPRI	1.3.6.1.4.1.171.10.113.1.6.2.17.3.1.1.4	INTEGER	read-write	Enable IP priority QoS. When set tos (2), enable TOS based QoS; When set dscp (3), enable DSCP based QoS; When set disable (1), disable IP priority QoS.
INT swL2CosPriorityNone	1.3.6.1.4.1.171.10.113.1.6.2.17.3.1.1.5	INTEGER	read-write	When read, it always returns invalid (2); when write valid (1), it disables all priority in this table.
swL2CosTosPRITable	1.3.6.1.4.1.171.10.113.1.6.2.17.3.4		not-accessible	Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.
swL2CosTosPRIEntry	1.3.6.1.4.1.171.10.113.1.6.2.17.3.4.1		not-accessible	A list of information contained in the swL2CosTosPRITable.
INT swL2CosTosPRIIndex	1.3.6.1.4.1.171.10.113.1.6.2.17.3.4.1.1	INTEGER	read-only	Indicates the CoS Priority TosPRI.
INT swL2CosTosPRIClass	1.3.6.1.4.1.171.10.113.1.6.2.17.3.4.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
swL2CosDscpPRITable	1.3.6.1.4.1.171.10.113.1.6.2.17.3.5		not-accessible	Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.
swL2CosDscpPRIEntry	1.3.6.1.4.1.171.10.113.1.6.2.17.3.5.1		not-accessible	A list of information contained in the swL2CosDscpPRITable.
INT swL2CosDscpPRIIndex	1.3.6.1.4.1.171.10.113.1.6.2.17.3.5.1.1	INTEGER	read-only	Indicates the CoS Priority DscpPRI.
INT swL2CosDscpPRIClass	1.3.6.1.4.1.171.10.113.1.6.2.17.3.5.1.2	INTEGER	read-write	The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
swL2DhcpRelayMgmt	1.3.6.1.4.1.171.10.113.1.6.2.18
INT swL2DhcpRelayState	1.3.6.1.4.1.171.10.113.1.6.2.18.1	INTEGER	read-write	This object indicates whether the DHCP relay function is enabled or disabled.
INT swL2DhcpRelayHopCount	1.3.6.1.4.1.171.10.113.1.6.2.18.2	INTEGER	read-write	This object indicates the maximum number of router hops that the DHCP packets can cross.
INT swL2DhcpRelayTimeThreshold	1.3.6.1.4.1.171.10.113.1.6.2.18.3	INTEGER	read-write	This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
INT swL2DhcpRelayOption82State	1.3.6.1.4.1.171.10.113.1.6.2.18.4	INTEGER	read-write	This object indicates DHCP relay agent information option 82 function is enabled or disabled.
INT swL2DhcpRelayOption82Check	1.3.6.1.4.1.171.10.113.1.6.2.18.5	INTEGER	read-write	This object indicates the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
INT swL2DhcpRelayOption82Policy	1.3.6.1.4.1.171.10.113.1.6.2.18.6	INTEGER	read-write	This object indicates the reforwarding policy of DHCP relay agent information option 82. replace (1) - Replace the exiting option 82 field in messages. drop (2) - Discard messages with existing option 82 field. keep (3) - Retain the existing option 82 field in messages.
swL2DhcpRelayCtrlTable	1.3.6.1.4.1.171.10.113.1.6.2.18.7		not-accessible	This table specifies the IP address as a destination to forward (relay) DHCP packets to.
swL2DhcpRelayCtrlEntry	1.3.6.1.4.1.171.10.113.1.6.2.18.7.1		not-accessible	A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
STR swL2DhcpRelayCtrlInterfaceName	1.3.6.1.4.1.171.10.113.1.6.2.18.7.1.1	DisplayString	read-only	The name of the IP interface.
IP swL2DhcpRelayCtrlServer	1.3.6.1.4.1.171.10.113.1.6.2.18.7.1.2	IpAddress	read-only	The DHCP server IP address.
INT swL2DhcpRelayCtrlState	1.3.6.1.4.1.171.10.113.1.6.2.18.7.1.3	INTEGER	read-write	This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) - Writing this value to the object, and then the corresponding entry will be removed from the table. valid (3) - This entry resides in the table.
swL2MgmtMIBTraps	1.3.6.1.4.1.171.10.113.1.6.2.20
swL2MgmtMIBTrapPrefix	1.3.6.1.4.1.171.10.113.1.6.2.20.0
NTF swL2PortSecurityViolationTrap	1.3.6.1.4.1.171.10.113.1.6.2.20.0.1			When the port_security trap is enabled, if there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out.
NTF swL2macNotification	1.3.6.1.4.1.171.10.113.1.6.2.20.0.2			This trap indicates the MAC address variations in the address table.
NTF swL2PortLoopOccurred	1.3.6.1.4.1.171.10.113.1.6.2.20.0.3			The trap is sent when a Port loop occurs.
NTF swL2PortLoopRestart	1.3.6.1.4.1.171.10.113.1.6.2.20.0.4			The trap is sent when a Port loop restarts after the interval time.
NTF swL2VlanLoopOccurred	1.3.6.1.4.1.171.10.113.1.6.2.20.0.5			The trap is sent when a Port with a VID loop occurs.
NTF swL2VlanLoopRestart	1.3.6.1.4.1.171.10.113.1.6.2.20.0.6			The trap is sent when a Port with a VID loop restarts after the interval time.
swl2PortSecurityBindings	1.3.6.1.4.1.171.10.113.1.6.2.20.1
MAC swL2PortSecurityViolationMac	1.3.6.1.4.1.171.10.113.1.6.2.20.1.1	MacAddress	accessible-for-notify	This object indicates the MAC address that violates the port security configuration.
swl2NotificationBindings	1.3.6.1.4.1.171.10.113.1.6.2.20.2
OCT swL2macNotifyInfo	1.3.6.1.4.1.171.10.113.1.6.2.20.2.1	OCTET STRING	read-only	This object indicates the last time reboot information.
INT swL2VlanLoopDetectVID	1.3.6.1.4.1.171.10.113.1.6.2.20.2.2	INTEGER	accessible-for-notify	This object indicates the VID that detected a loopback.
swL2LoopDetectMgmt	1.3.6.1.4.1.171.10.113.1.6.2.21
swL2LoopDetectCtrl	1.3.6.1.4.1.171.10.113.1.6.2.21.1
INT swL2LoopDetectAdminState	1.3.6.1.4.1.171.10.113.1.6.2.21.1.1	INTEGER	read-write	This object indicates the loopback detection status for the system.
INT swL2LoopDetectInterval	1.3.6.1.4.1.171.10.113.1.6.2.21.1.2	INTEGER	read-write	This object indicates the interval value, the range is from 1 to 32767 seconds.
INT swL2LoopDetectRecoverTime	1.3.6.1.4.1.171.10.113.1.6.2.21.1.3	INTEGER	read-write	This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
INT swL2LoopDetectMode	1.3.6.1.4.1.171.10.113.1.6.2.21.1.4	INTEGER	read-write	This object indicates the loopback detection mode for the system.
INT swL2LoopDetectTrapMode	1.3.6.1.4.1.171.10.113.1.6.2.21.1.5	INTEGER	read-write	This object indicates the loopback detection trap mode for the system.
swL2LoopDetectPortMgmt	1.3.6.1.4.1.171.10.113.1.6.2.21.2
swL2LoopDetectPortTable	1.3.6.1.4.1.171.10.113.1.6.2.21.2.1		not-accessible	The table specifies the loopback detection function specified by port.
swL2LoopDetectPortEntry	1.3.6.1.4.1.171.10.113.1.6.2.21.2.1.1		not-accessible	The table specifies the loopback detection function specified by port.
INT swL2LoopDetectPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.21.2.1.1.1	INTEGER	read-only	This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
INT swL2LoopDetectPortState	1.3.6.1.4.1.171.10.113.1.6.2.21.2.1.1.2	INTEGER	read-write	This object indicates the loopback detection function state on the port.
STR swL2LoopDetectPortLoopVLAN	1.3.6.1.4.1.171.10.113.1.6.2.21.2.1.1.3	DisplayString	read-only	This object indicates the VLAN list that has detected a loopback.
INT swL2LoopDetectPortLoopStatus	1.3.6.1.4.1.171.10.113.1.6.2.21.2.1.1.4	INTEGER	read-only	This object indicates the port status.
swL2MultiFilter	1.3.6.1.4.1.171.10.113.1.6.2.22
swL2McastFilterTable	1.3.6.1.4.1.171.10.113.1.6.2.22.2		not-accessible	A table that contains information about the multicast filter address.
swL2McastFilterEntry	1.3.6.1.4.1.171.10.113.1.6.2.22.2.1		not-accessible	A list of multicast filter mode information for each profile ID.
INT swL2McastFilterProfileIndex	1.3.6.1.4.1.171.10.113.1.6.2.22.2.1.1	INTEGER	read-only	index for each profile
STR swL2McastFilterProfileName	1.3.6.1.4.1.171.10.113.1.6.2.22.2.1.2	DisplayString	read-write	The multicast filter description.
INT swL2McastFilterAddOrDelState	1.3.6.1.4.1.171.10.113.1.6.2.22.2.1.3	INTEGER	read-write	The control multicast filter address.
STR swL2McastFilterGroupList	1.3.6.1.4.1.171.10.113.1.6.2.22.2.1.4	DisplayString	read-write	The multicast filter address group list.
ROW swL2McastFilterStatus	1.3.6.1.4.1.171.10.113.1.6.2.22.2.1.5	RowStatus	read-create	This object indicates the status of this entry.
swL2McastFilterPortTable	1.3.6.1.4.1.171.10.113.1.6.2.22.3		not-accessible	A table that is used to bind port to profile ID.
swL2McastFilterPortEntry	1.3.6.1.4.1.171.10.113.1.6.2.22.3.1		not-accessible	A list of information that is used to bind port to profile ID.
INT swL2McastFilterPortGroupPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.22.3.1.1	INTEGER	read-only	The port index.
INT swL2McastFilterPortProfileAddOrDelState	1.3.6.1.4.1.171.10.113.1.6.2.22.3.1.2	INTEGER	read-write	The control multicast filter profile.
INT swL2McastFilterPortProfileID	1.3.6.1.4.1.171.10.113.1.6.2.22.3.1.3	INTEGER	read-write	This object indicates the profile ID of this entry. When read, it is always 0. When set, 0 can not be set.
INT swL2McastFilterPortAccess	1.3.6.1.4.1.171.10.113.1.6.2.22.3.1.4	INTEGER	read-write	This object indicates the access status for each port. When read, it is always none. When set, none can not be set.
swL2McastFilterPortMaxGroupTable	1.3.6.1.4.1.171.10.113.1.6.2.22.4		not-accessible	A table that contains information about the max group number based on port.
swL2McastFilterPortMaxGroupEntry	1.3.6.1.4.1.171.10.113.1.6.2.22.4.1		not-accessible	A list of max group number information for each port.
INT swL2McastFilterPortMaxGroupPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.22.4.1.1	INTEGER	read-only	The port index.
INT swL2McastFilterPortMaxGroup	1.3.6.1.4.1.171.10.113.1.6.2.22.4.1.2	INTEGER	read-write	The max group numbers. The default is 256.
swL2McastFilterPortInfoTable	1.3.6.1.4.1.171.10.113.1.6.2.22.5		not-accessible	A table that contains information about all of the multicast groups for the ports.
swL2McastFilterPortInfoEntry	1.3.6.1.4.1.171.10.113.1.6.2.22.5.1		not-accessible	A list of information about all of the multicast groups for each port.
INT swL2McastFilterPortInfoPortIndex	1.3.6.1.4.1.171.10.113.1.6.2.22.5.1.1	INTEGER	read-only	The port index.
STR swL2McastFilterPortInfoProfileID	1.3.6.1.4.1.171.10.113.1.6.2.22.5.1.2	DisplayString	read-only	The multicast filter address profile ID.
INT swL2McastFilterPortInfoAccess	1.3.6.1.4.1.171.10.113.1.6.2.22.5.1.3	INTEGER	read-only	This object indicates the access status for each port.
swL2VlanMgmt	1.3.6.1.4.1.171.10.113.1.6.2.23
swL2VlanAdvertisementTable	1.3.6.1.4.1.171.10.113.1.6.2.23.1		not-accessible	A table containing the advertisement state for each VLAN configured into the device by (local or network) management.
swL2VlanAdvertisementEntry	1.3.6.1.4.1.171.10.113.1.6.2.23.1.1		not-accessible	The advertisement state for each VLAN configured into the device.
INT swL2VlanIndex	1.3.6.1.4.1.171.10.113.1.6.2.23.1.1.1	INTEGER	read-only	The VLAN-ID or other identifier referring to this VLAN.
STR swL2VlanName	1.3.6.1.4.1.171.10.113.1.6.2.23.1.1.2	DisplayString	read-only	An administratively assigned string, which may be used to identify the VLAN.
INT swL2VlanAdvertiseState	1.3.6.1.4.1.171.10.113.1.6.2.23.1.1.3	INTEGER	read-write	This object indicates the advertise status of this VLAN entry.
swL2VlanMultiplyMgmt	1.3.6.1.4.1.171.10.113.1.6.2.23.2
STR swL2VlanMultiplyVlanList	1.3.6.1.4.1.171.10.113.1.6.2.23.2.1	DisplayString	read-write	This object specifies the VLAN ID List.
INT swL2VlanMultiplyAdvertisement	1.3.6.1.4.1.171.10.113.1.6.2.23.2.2	INTEGER	read-write	This object specifies the advertisement state.
POR swL2VlanMultiplyPortList	1.3.6.1.4.1.171.10.113.1.6.2.23.2.3	PortList	read-write	Specifies the port list.
INT swL2VlanMultiplyPortListAction	1.3.6.1.4.1.171.10.113.1.6.2.23.2.4	INTEGER	read-write	Specifies the action for the port list which specified by swL2VlanMultiplyPortList.
INT swL2VlanMultiplyAction	1.3.6.1.4.1.171.10.113.1.6.2.23.2.5	INTEGER	read-write	Specifies the action for VLANs. other: no action. create: the VLANs specified by swL2VlanMultiplyVlanList would be created at a time. configure: the VLANs specified by swL2VlanMultiplyVlanList would be configured at a time. delete: the VLANs specified by swL2VlanMultiplyVlanList would be deleted at a time.
INT swL2PVIDAutoAssignmentState	1.3.6.1.4.1.171.10.113.1.6.2.23.3	INTEGER	read-write	This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change PVID. If 'Auto-assign PVID' is enabled, PVID will be possibly changed by PVID or VLAN configuration. When user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. In the form of VLAN list command, PVID is updated with last item of VLAN list. When user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned with 'default VLAN'.
swL2DhcpLocalRelayMgmt	1.3.6.1.4.1.171.10.113.1.6.2.24
INT swL2DhcpLocalRelayState	1.3.6.1.4.1.171.10.113.1.6.2.24.1	INTEGER	read-write	This object indicates the status of the DHCP local relay function of the switch.
swL2DhcpLocalRelayVLANTable	1.3.6.1.4.1.171.10.113.1.6.2.24.2		not-accessible	This table is used to manage the DHCP local relay status for each VLAN.
swL2DhcpLocalRelayVLANEntry	1.3.6.1.4.1.171.10.113.1.6.2.24.2.1		not-accessible	This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
INT swL2DhcpLocalRelayVLANID	1.3.6.1.4.1.171.10.113.1.6.2.24.2.1.1	INTEGER	read-only	This object shows the VIDs of the current VLANS in the switch.
INT swL2DhcpLocalRelayVLANState	1.3.6.1.4.1.171.10.113.1.6.2.24.2.1.2	INTEGER	read-write	This object indicates the status of the DHCP relay function of the VLAN.

RFC description

Provides Layer 2 management for D-Link DES3200 switches including VLAN, spanning tree, and port control.

Start monitoring D-Link DES-3200ME-28 managed switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DES3200ME-28-L2MGMT-MIB

What Is DES3200ME-28-L2MGMT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description