All MIBs › DASAN-SHDSL-MIB
Organization: Dasan Co., Ltd.
Last Updated: 2004-07-15
Category: DASAN Networks, DSL / Broadband Access
Description: Monitors SHDSL line performance, margin, and error counters on Dasan DSL access equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is DASAN-SHDSL-MIB?
DASAN-SHDSL-MIB is a Dasan Co., Ltd. proprietary MIB (extending the standard SHDSL-LINE-MIB via ADSL-LINE-MIB conventions) reporting G.SHDSL line status and remote-unit detail. Its line-status table, keyed by interface, records operational state, startup progress, firmware release, line-swap flag, remote country code, encoder A/B, remote provider code, local-detect state, TX power, framer sync, remote TOM data, drift alarm, receiver gain, BERT error, framer overhead/defects, remote firmware version, and UTOPIA cell-delineation/RX-cell/drop/HEC-error/TX-cell counts. As a performance/status MIB it lets an administrator confirm G.SHDSL line sync quality and watch UTOPIA cell-delineation errors on a Dasan SHDSL device. It is deployed on Dasan Co. G.SHDSL access equipment. Engineers can download the DASAN-SHDSL-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in DASAN-SHDSL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Dasan Co. G.SHDSL access equipment
Monitoring Examples
An administrator checks dsShdslOpState and dsShdslUtopiaRxHecErrorCnt to diagnose a degraded G.SHDSL line on a Dasan device.
What Can Be Monitored
- G.SHDSL line sync quality and UTOPIA cell-delineation errors
This MIB depends on
Related MIBs
Imported Objects
From DASAN-SMI
| dasanMgmt | OBJECT-IDENTITY |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 | |
| mib-2 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| dasanShdslMIB | 1.3.6.1.4.1.6296.9.6 | The MIB module to describe G.SHDSL product. The MIB module that provides objects that are proprietary and extension to SHDSL- LINE-MIB. The MIB include extension to following Tables. The MIB also include a set of scalar(s) clubbed under the group 'dsShdslCapabilityGroup'. | ||
| dasanShdslLineMIB | 1.3.6.1.4.1.6296.9.6.1 | |||
| dasanShdslMIBObjects | 1.3.6.1.4.1.6296.9.6.1.1 | |||
| dsShdslCapabilityGroup | 1.3.6.1.4.1.6296.9.6.1.1.1 | |||
| BIT dsShdslCapabilityLineTxCap | 1.3.6.1.4.1.6296.9.6.1.1.1.1 | Bits | read-only | This bitmap specifies the transmission modes that the STU-C is capable of supporting. Right now, support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MxU. |
| dsShdslLineStatusTable | 1.3.6.1.4.1.6296.9.6.1.1.2 | not-accessible | This MO is proprietary extension of RFC 3276 MIB and contains the proprietary line status. | |
| dsShdslLineStatusEntry | 1.3.6.1.4.1.6296.9.6.1.1.2.1 | not-accessible | An entry (conceptual row) in the dsShdslLineStatusTable. The Table is indexed by ifIndex. | |
| INT dsShdslOpState | 1.3.6.1.4.1.6296.9.6.1.1.2.1.1 | INTEGER | read-only | This object identifies the high level operational state for the STU. |
| INT dsShdslStartProgress | 1.3.6.1.4.1.6296.9.6.1.1.2.1.2 | INTEGER | read-only | This object identifies the current detailed operational state of the STU. |
| OCT dsShdslFwRelease | 1.3.6.1.4.1.6296.9.6.1.1.2.1.3 | OCTET STRING | read-only | Transceiver firmware release number. |
| INT dsShdslLineSwap | 1.3.6.1.4.1.6296.9.6.1.1.2.1.4 | INTEGER | read-only | This object indicates if the physical lines are swapped, i.e., logical channel A is connected to physical channel B. This applies to 4-wire operation only. |
| OCT dsShdslRmtCountryCode | 1.3.6.1.4.1.6296.9.6.1.1.2.1.5 | OCTET STRING | read-only | This object provides the country code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. GlobespanVirata sets this to USA. |
| INT dsShdslRmtEncoderA | 1.3.6.1.4.1.6296.9.6.1.1.2.1.6 | INTEGER | read-only | This object identifies the 21-bit value corresponding to encoder coefficient A, as defined in ITU-T G.991.2, for the STU at the other end of the loop. |
| INT dsShdslRmtEncoderB | 1.3.6.1.4.1.6296.9.6.1.1.2.1.7 | INTEGER | read-only | This object identifies the 21-bit value corresponding to encoder coefficient B, as defined in ITU-T G.991.2, for the STU at the other end of the loop. |
| OCT dsShdslRmtProviderCode | 1.3.6.1.4.1.6296.9.6.1.1.2.1.8 | OCTET STRING | read-only | This object identifies the provider code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. |
| INT dsShdslLocDetect | 1.3.6.1.4.1.6296.9.6.1.1.2.1.9 | INTEGER | read-only | This object is used to determine if carrier has been lost. |
| INT dsShdslTxPower | 1.3.6.1.4.1.6296.9.6.1.1.2.1.10 | INTEGER | read-only | This object identifies the local STU transmit power in tenths of a dBm. |
| INT dsShdslFramerSync | 1.3.6.1.4.1.6296.9.6.1.1.2.1.11 | INTEGER | read-only | This object returns information regarding the framer synchronization status. |
| INT dsShdslRmtTomData | 1.3.6.1.4.1.6296.9.6.1.1.2.1.12 | INTEGER | read-only | This object provides vendor-provided data, as defined in ITU-T G.991.2, for the STU at the other end of the loop. |
| INT dsShdslDriftAlarm | 1.3.6.1.4.1.6296.9.6.1.1.2.1.13 | INTEGER | read-only | This object identifies if the receive clock is in or out of range. |
| INT dsShdslReceiverGain | 1.3.6.1.4.1.6296.9.6.1.1.2.1.14 | INTEGER | read-only | This object provides the total receiver gain in dB. |
| INT dsShdslBertError | 1.3.6.1.4.1.6296.9.6.1.1.2.1.15 | INTEGER | read-only | This object provides the count of bit errors since the last time the object was read, as well as the type of synchronization. |
| OCT dsShdslFramerOHAndDefects | 1.3.6.1.4.1.6296.9.6.1.1.2.1.16 | OCTET STRING | read-only | This object returns overhead data. The four least significant bits contain the overhead data in the following format: bit 0 is losd, bit 1 is sega, bit 2 is ps, and bit 3 is segd. |
| INT dsShdslRmtFwVersion | 1.3.6.1.4.1.6296.9.6.1.1.2.1.17 | INTEGER | read-only | This object provides the transceiver firmware release number of the STU at the other end of the loop. |
| INT dsShdslUtopiaCellDelineation | 1.3.6.1.4.1.6296.9.6.1.1.2.1.18 | INTEGER | read-only | This object indicates whether cell delineation has been found. |
| INT dsShdslUtopiaRxCellCnt | 1.3.6.1.4.1.6296.9.6.1.1.2.1.19 | INTEGER | read-only | This object indicates the number of UTOPIA cells received since the last time the object has been called. The maximum value is 0xFFFF. |
| INT dsShdslUtopiaCellDropCnt | 1.3.6.1.4.1.6296.9.6.1.1.2.1.20 | INTEGER | read-only | This object indicates the number of UTOPIA cells dropped since the last time the object has been called. The maximum value is 0xFF. |
| INT dsShdslUtopiaRxHecErrorCnt | 1.3.6.1.4.1.6296.9.6.1.1.2.1.21 | INTEGER | read-only | This object indicates the number of UTOPIA cells with HEC errors since the last time the object has been called. The maximum value is 0xFF. |
| INT dsShdslUtopiaTxCellCnt | 1.3.6.1.4.1.6296.9.6.1.1.2.1.22 | INTEGER | read-only | This object indicates the number of UTOPIA cells transmitted since the last time the object has been called. The maximum value is 0xFFFF. |
| INT dsShdslRmtNsfCusId | 1.3.6.1.4.1.6296.9.6.1.1.2.1.23 | INTEGER | read-only | This object returns the customer identification that was sent by the STU at the other end of the loop. |
| OCT dsShdslRmtNsfCusData | 1.3.6.1.4.1.6296.9.6.1.1.2.1.24 | OCTET STRING | read-only | This object returns non-standard format customer data that was sent by the STU at the other end of the loop. |
| OCT dsShdslLocalHandshake | 1.3.6.1.4.1.6296.9.6.1.1.2.1.25 | OCTET STRING | read-only | This object provides a way to see what capabilities are supported by the local STU. A total of 26 handshake parameters are supported. |
| OCT dsShdslRemoteHandshake | 1.3.6.1.4.1.6296.9.6.1.1.2.1.26 | OCTET STRING | read-only | This object provides a way to see what capabilities are supported by the STU at the other end of the loop. A total of 26 handshake parameters are supported. |
| OCT dsShdslActualHandshake | 1.3.6.1.4.1.6296.9.6.1.1.2.1.27 | OCTET STRING | read-only | This object provides the results of capabilities exchanged during handshake. A total of 26 handshake parameters are supported. |
| INT dsShdslRmtTxPower | 1.3.6.1.4.1.6296.9.6.1.1.2.1.28 | INTEGER | read-only | This object provides the transmit power of the STU at the other end of the loop. |
| INT dsShdslRmtPowerBackoff | 1.3.6.1.4.1.6296.9.6.1.1.2.1.29 | INTEGER | read-only | This object indicates whether power backoff is enabled or disabled at the STU at the other end of the loop. |
| INT dsShdslAutoRetrainCount | 1.3.6.1.4.1.6296.9.6.1.1.2.1.30 | INTEGER | read-only | This object indicates the number of automatic retrains. This counter is only reset when a startup is initiated. |
| INT dsShdslEocState | 1.3.6.1.4.1.6296.9.6.1.1.2.1.31 | INTEGER | read-only | This object provides status information about the eoc stage. |
| OCT dsShdslFramerOneSecondCnt | 1.3.6.1.4.1.6296.9.6.1.1.2.1.32 | OCTET STRING | read-only | This object provides CRC, SEGA, and LOSW defect one second error counts, and should be called every second. |
| INT dsShdslNtrFault | 1.3.6.1.4.1.6296.9.6.1.1.2.1.33 | INTEGER | read-only | This object identifies the Network Timing Recovery Fault. |
| INT dsShdslCpeMasterCore | 1.3.6.1.4.1.6296.9.6.1.1.2.1.34 | INTEGER | read-only | |
| INT dsShdslParametricTestResult | 1.3.6.1.4.1.6296.9.6.1.1.2.1.35 | INTEGER | read-only | Indicates the Result of the Parametric Test conducted on the Xcvr. |
| OCT dsShdslParametricTestArray | 1.3.6.1.4.1.6296.9.6.1.1.2.1.36 | OCTET STRING | read-only | Conexant parameter that indicates the Parametric Test Array. |
| dsShdslLineParamsTable | 1.3.6.1.4.1.6296.9.6.1.1.3 | not-accessible | This MO is proprietary extension of RFC 3276 MIB and contains the proprietary line parameters. | |
| dsShdslLineParamsEntry | 1.3.6.1.4.1.6296.9.6.1.1.3.1 | not-accessible | An entry (conceptual row) in the dsShdslLineParamsTable. The Table is indexed by ifIndex. | |
| INT dsShdslAction | 1.3.6.1.4.1.6296.9.6.1.1.3.1.1 | INTEGER | read-write | This object specifies actions that are used to control transceiver operation. |
| INT dsShdslMode | 1.3.6.1.4.1.6296.9.6.1.1.3.1.2 | INTEGER | read-write | This object specifies the operational mode of the transceiver. |
| INT dsShdslPowerScale | 1.3.6.1.4.1.6296.9.6.1.1.3.1.3 | INTEGER | read-write | This object is used to compensate for minor differences in transmit power between designs. |
| INT dsShdslFramerType | 1.3.6.1.4.1.6296.9.6.1.1.3.1.4 | INTEGER | read-only | This object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces. |
| INT dsShdslAFEType | 1.3.6.1.4.1.6296.9.6.1.1.3.1.5 | INTEGER | read-only | This objects defines which AFE is being used. |
| INT dsShdslEncodeCoeffA | 1.3.6.1.4.1.6296.9.6.1.1.3.1.6 | INTEGER | read-write | This object determines the value of encoder coefficient A, as defined in ITU-T G.991.2. |
| INT dsShdslEncodeCoeffB | 1.3.6.1.4.1.6296.9.6.1.1.3.1.7 | INTEGER | read-write | This object determines the value of encoder coefficient B, as defined in ITU-T G.991.2 |
| INT dsShdslTxEOCBufferLen | 1.3.6.1.4.1.6296.9.6.1.1.3.1.8 | INTEGER | read-write | This object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction. |
| INT dsShdslRxEOCBufferLen | 1.3.6.1.4.1.6296.9.6.1.1.3.1.9 | INTEGER | read-write | This object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction. |
| INT dsShdslNTR | 1.3.6.1.4.1.6296.9.6.1.1.3.1.10 | INTEGER | read-write | This object defines how network-timing recovery is performed. |
| INT dsShdslRxUpstreamFrameSync | 1.3.6.1.4.1.6296.9.6.1.1.3.1.11 | INTEGER | read-write | Customer-defined value. This object defines the upstream frame sync word. |
| INT dsShdslRxDownstreamFrameSync | 1.3.6.1.4.1.6296.9.6.1.1.3.1.12 | INTEGER | read-write | This object defines the downstream frame sync word. |
| INT dsShdslRxUpstreamStuffBits | 1.3.6.1.4.1.6296.9.6.1.1.3.1.13 | INTEGER | read-write | Customer-defined value. This object defines the upstream. |
| INT dsShdslRxDownstreamStuffBits | 1.3.6.1.4.1.6296.9.6.1.1.3.1.14 | INTEGER | read-write | This object defines the downstream stuff bits. |
| INT dsShdslInitiate | 1.3.6.1.4.1.6296.9.6.1.1.3.1.15 | INTEGER | read-write | This object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits. |
| INT dsShdslFramerRxClockMode | 1.3.6.1.4.1.6296.9.6.1.1.3.1.16 | INTEGER | read-write | This object determines the source of the receive clock. |
| INT dsShdslFramerRxPllMode | 1.3.6.1.4.1.6296.9.6.1.1.3.1.17 | INTEGER | read-write | This object enables or disables the internal PLL. |
| INT dsShdslSerialAtmCiuBufferSize | 1.3.6.1.4.1.6296.9.6.1.1.3.1.18 | INTEGER | read-write | This object enables the user to set the size of the framer buffer for serial ATM operation. |
| INT dsShdslUtopiaL2TxAddress | 1.3.6.1.4.1.6296.9.6.1.1.3.1.19 | INTEGER | read-only | This object selects the appropriate UTOPIA Level 2 address for the transmit interface. |
| INT dsShdslUtopiaL2RxAddress | 1.3.6.1.4.1.6296.9.6.1.1.3.1.20 | INTEGER | read-only | This object selects the appropriate UTOPIA Level 2 address for the receive interface. |
| INT dsShdslTxFramerPulseDelay | 1.3.6.1.4.1.6296.9.6.1.1.3.1.21 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the transmit frame pulse. |
| INT dsShdslRxFramerPulseDelay | 1.3.6.1.4.1.6296.9.6.1.1.3.1.22 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the receive frame pulse. |
| INT dsShdslMultiFrameMode | 1.3.6.1.4.1.6296.9.6.1.1.3.1.23 | INTEGER | read-write | This object specifies the multi frame operational mode of the transceiver. |
| INT dsShdslEnable4or6MbpsBitrate | 1.3.6.1.4.1.6296.9.6.1.1.3.1.24 | INTEGER | read-write | This object specifies the operational state of the 4_6Mbps bit rate. |
| INT dsShdslTomDataWord1 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.25 | INTEGER | read-write | This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. |
| INT dsShdslTomDataWord2 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.26 | INTEGER | read-write | This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. |
| INT dsShdslTomDataWord3 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.27 | INTEGER | read-write | This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. |
| INT dsShdslTomDataWord4 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.28 | INTEGER | read-write | This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. |
| INT dsShdslSetReqSilenceMode | 1.3.6.1.4.1.6296.9.6.1.1.3.1.29 | INTEGER | read-write | This object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could perform whatever operations it wants and the STU at the opposite end will remain in handshake. |
| INT dsShdslSetIndividualRates1 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.30 | INTEGER | read-write | This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled. |
| INT dsShdslSetIndividualRates2 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.31 | INTEGER | read-write | This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled. |
| INT dsShdslSetIndividualRates3 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.32 | INTEGER | read-write | This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled. |
| INT dsShdslSatmCellDelineation | 1.3.6.1.4.1.6296.9.6.1.1.3.1.33 | INTEGER | read-write | This object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup. |
| INT dsShdslFramerCellDropOnError | 1.3.6.1.4.1.6296.9.6.1.1.3.1.34 | INTEGER | read-write | This object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup. |
| INT dsShdslGearShiftType | 1.3.6.1.4.1.6296.9.6.1.1.3.1.35 | INTEGER | read-write | This object specifies the Gear Shift Type. |
| INT dsShdslHsNsf | 1.3.6.1.4.1.6296.9.6.1.1.3.1.36 | INTEGER | read-write | This object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis. |
| INT dsShdslHsMaxBitsPerBaud | 1.3.6.1.4.1.6296.9.6.1.1.3.1.37 | INTEGER | read-write | This object specifies the maximum bit per baud. |
| INT dsShdslHsCusId | 1.3.6.1.4.1.6296.9.6.1.1.3.1.38 | INTEGER | read-write | This object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis. |
| INT dsShdslHsCusData0 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.39 | INTEGER | read-write | This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis. |
| INT dsShdslHsCusData1 | 1.3.6.1.4.1.6296.9.6.1.1.3.1.40 | INTEGER | read-write | This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis. |
| INT dsShdslHsAnnexBType | 1.3.6.1.4.1.6296.9.6.1.1.3.1.41 | INTEGER | read-write | This object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both. |
| INT dsShdslAutoRetrain | 1.3.6.1.4.1.6296.9.6.1.1.3.1.42 | INTEGER | read-write | Enables or disables auto-retrain. |
| INT dsShdslArCrcCheck | 1.3.6.1.4.1.6296.9.6.1.1.3.1.43 | INTEGER | read-write | Enables or disables auto-retrain based on CRC errors. |
| INT dsShdslArFramerSyncCheck | 1.3.6.1.4.1.6296.9.6.1.1.3.1.44 | INTEGER | read-write | Enables or disables auto-retrain based on framer synchronization. |
| INT dsShdslArSnrMarginCheck | 1.3.6.1.4.1.6296.9.6.1.1.3.1.45 | INTEGER | read-write | Enables or disables auto-retrain based on whether the S/N margin falls below a preset threshold. |
| INT dsShdslArCrcThreshold | 1.3.6.1.4.1.6296.9.6.1.1.3.1.46 | INTEGER | read-write | Sets the threshold for the number of frames with CRC errors for autoretrain. |
| INT dsShdslArSnrMarginThreshold | 1.3.6.1.4.1.6296.9.6.1.1.3.1.47 | INTEGER | read-write | Set the margin threshold for autoretrain. |
| INT dsShdslArRetrainTime | 1.3.6.1.4.1.6296.9.6.1.1.3.1.48 | INTEGER | read-write | Sets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs. |
| INT dsShdslOpStateTrapEnable | 1.3.6.1.4.1.6296.9.6.1.1.3.1.49 | INTEGER | read-write | Enables/disables trap indicating a change in op state. |
| INT dsShdslTxFrmrDataClkEdge | 1.3.6.1.4.1.6296.9.6.1.1.3.1.50 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either rising or falling edge of the transmit clock. |
| INT dsShdslRxFrmrDataClkEdge | 1.3.6.1.4.1.6296.9.6.1.1.3.1.51 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either rising or falling edge of the receive clock. |
| INT dsShdslTxFrmrPulseClkEdge | 1.3.6.1.4.1.6296.9.6.1.1.3.1.52 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge. |
| INT dsShdslRxFrmrPulseClkEdge | 1.3.6.1.4.1.6296.9.6.1.1.3.1.53 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge. |
| INT dsShdslTxFrmrPulseLvl | 1.3.6.1.4.1.6296.9.6.1.1.3.1.54 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0). |
| INT dsShdslRxFrmrPulseLvl | 1.3.6.1.4.1.6296.9.6.1.1.3.1.55 | INTEGER | read-write | This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0). |
| INT dsShdslUtopiaDataBusWidth | 1.3.6.1.4.1.6296.9.6.1.1.3.1.56 | INTEGER | read-only | This parameter is used to specify width of UTOPIA data bus. |
| INT dsShdslFrmrOH | 1.3.6.1.4.1.6296.9.6.1.1.3.1.57 | INTEGER | read-write | This object specifies framer OverHead Channel. |
| INT dsShdslLoopAttenCrossingTrapEnable | 1.3.6.1.4.1.6296.9.6.1.1.3.1.58 | INTEGER | read-write | This Parameter enables or disables the Trap for Loop Attenuation Threshold crossing. |
| INT dsShdslSNRMarginCrossingTrapEnable | 1.3.6.1.4.1.6296.9.6.1.1.3.1.59 | INTEGER | read-write | This Parameter enables or disables the Trap for SNR Margin Threshold crossing. |
| INT dsShdslFramerOHAndDefectsTrapEnable | 1.3.6.1.4.1.6296.9.6.1.1.3.1.60 | INTEGER | read-write | This Parameter enables or disables the Trap for Framer Overhead and Defects. |
| STR dsShdslParametricTestInputFile | 1.3.6.1.4.1.6296.9.6.1.1.3.1.61 | DisplayString | read-write | Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified. |
| INT dsShdslParamHybridLossTestStart | 1.3.6.1.4.1.6296.9.6.1.1.3.1.62 | INTEGER | read-write | Indicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-AN. |
| INT dsShdslParamHybridLossTestEnd | 1.3.6.1.4.1.6296.9.6.1.1.3.1.63 | INTEGER | read-write | Indicates End bin for range of bins to be measured. The default value mentioned is an indicative value only. |
| dsShdslSpanStatusExtnTable | 1.3.6.1.4.1.6296.9.6.1.1.4 | not-accessible | This table is a proprietary extension of hdsl2ShdslSpanStatusTable | |
| dsShdslSpanStatusExtnEntry | 1.3.6.1.4.1.6296.9.6.1.1.4.1 | not-accessible | An entry (conceptual row) in the dsShdslSpanStatusExtnTable. The Table is indexed by ifIndex. | |
| U32 dsShdslStatusPMMSMaxLineRate | 1.3.6.1.4.1.6296.9.6.1.1.4.1.1 | Unsigned32 | read-only | This object provides the maximum PMMS rate the line is capable of achieving |
| INT dsShdslStatus4WireHsMode | 1.3.6.1.4.1.6296.9.6.1.1.4.1.2 | INTEGER | read-only | Contains the current 4 Wire Handshake Mode Configured |
RFC description
G.SHDSL product management including line status, parameters, and proprietary extensions to RFC 3276.
Start monitoring Dasan Co. G.SHDSL access equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.