| OID symbolic | OID numeric | Type | Access | Description |
|---|
| cesmPort | 1.3.6.1.4.1.351.110.5.3.1 | | | |
| cesmPortCnfGrp | 1.3.6.1.4.1.351.110.5.3.1.1 | | | |
| cesmPortCnfGrpEntry | 1.3.6.1.4.1.351.110.5.3.1.1.1.1 | | not-accessible | An entry for each logical port. Each entry
contains information on the port type, DS0s
configured and number of DS0 subcircuits. |
| cesmPortCnfGrpTable | 1.3.6.1.4.1.351.110.5.3.1.1.1 | | not-accessible | The config table is for CES logical port.
This is used for configuring the port type
and number of DS0s and number of Subcircuits
in DS0 on the CES port. |
| INT cesPortBERTEnable | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.10 | INTEGER | read-write | This variable enables/disables BERT.
This object is not supported in CESM-T3E3. |
| I32 cesPortDs0ConfigBitMap | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.5 | Integer32 | read-write | This represents bit map of DS0s for a line which
are used to form this logical port. Bit 0 represents
DS0-1. |
| I32 cesPortLineNum | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.3 | Integer32 | read-write | This object represents the line number to
which this port is associated.
The supported range depends upon the type of
service module(card). |
| I32 cesPortNextAvailable | 1.3.6.1.4.1.351.110.5.3.1.1.2 | Integer32 | read-only | This variable contains the next UNUSED logical port number
of the possible 32 DS0s * n ports.
This number can be used in channel config table, the
cesportNextAvailable gets updated if the number gets
used to create a logical port.
A '0' indicates that no more ports are available. |
| I32 cesPortNum | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.1 | Integer32 | read-only | This object identifies the logical port number.
The range support depends upon the type of the
service module(Card).
- 8 port T1 Card, range is 1..192.
- 8 port E1 Card, range is 1..248.
- 1 port T3 Card, range is 1..1.
Range is caclulated as follows. This can be
used for calculating the range for other type
of cards.
For T1 Card: (24 * Number of T1 Ports)
For E1 Card: (31 * Number of E1 Ports). |
| I32 cesPortNumOfDs0Slot | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.6 | Integer32 | read-write | This represents number of DS0 time slots
configured to this Port. If the cesPortType is
strau(4), then this can not have more than 1 DS0 time slot. |
| I32 cesPortNumOfSCIPerDS0 | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.7 | Integer32 | read-write | This object represents number of subcircuit in
the DS0 time slot.
This is applicable only when cesPortType is
strau(4).
8 = there are 8 no .of 8kbps links (1 bit)
4 = there are 4 no .of 16kbps links (2 bit)
2 = there are 2 no .of 32kbps links (4 bit)
Currently not supported in CESM-8. |
| INT cesPortRowStatus | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.2 | INTEGER | read-write | This variable enables or modifies the port
1 - add : Add a logical port
2 - del : Delete a logical port
3 - mod : Modify a logical port. |
| I32 cesPortSpeed | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.8 | Integer32 | read-only | This object identifies the configured speed
of port.
Max speed for T1 = 1544
Max speed for E1 = 2038
Max speed for T3 = 44736
Max speed for E3 = 34368. |
| INT cesPortState | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.9 | INTEGER | read-only | This variable indicates the state of the
logical port.
The possible values are :
notConfigured (1) : Port is not configured
active (2) : Port is in active state
remoteLoopback (3) : Remote Loopback is set
failedDueToLine(4) : Port failed due to some failure in
physical line
failedDueToSignalling(5) : Port failed due to some Signalling
issues.
inactive (6) : Port is not active
inBert (7) : Bit Error Rate Test(BERT) in progress.
farEndRemoteLoopback(8): Far End is in loopback. |
| I32 cesPortsUsedLine1 | 1.3.6.1.4.1.351.110.5.3.1.1.3 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 1 |
| I32 cesPortsUsedLine2 | 1.3.6.1.4.1.351.110.5.3.1.1.4 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 2. |
| I32 cesPortsUsedLine3 | 1.3.6.1.4.1.351.110.5.3.1.1.5 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 3 |
| I32 cesPortsUsedLine4 | 1.3.6.1.4.1.351.110.5.3.1.1.6 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1.
This is for line 4 |
| I32 cesPortsUsedLine5 | 1.3.6.1.4.1.351.110.5.3.1.1.7 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 5 |
| I32 cesPortsUsedLine6 | 1.3.6.1.4.1.351.110.5.3.1.1.8 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 6 |
| I32 cesPortsUsedLine7 | 1.3.6.1.4.1.351.110.5.3.1.1.9 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 7 |
| I32 cesPortsUsedLine8 | 1.3.6.1.4.1.351.110.5.3.1.1.10 | Integer32 | read-only | Each bits set represents a DS0 that is used by all the
logical ports defined so far for that DS1, the most significant
byte is invalid for DS1
This is for line 8 |
| INT cesPortType | 1.3.6.1.4.1.351.110.5.3.1.1.1.1.4 | INTEGER | read-write | This object represents port type whether it is
carrying subrate circuits.
structured : This is for SDT(Structured Data Transfer).
This type of port supports following
features:
* intended to emulate point-to-point
fractional DS1 or E1 circuit.
* Synchronous timing
* Fractional(Nx64 Kbps)DS1/E1 service
(Contiguous timeslots only).You can
map an Nx64 Kbps channel to any Virtual
Channel(VC).
unstructured : This is for unstructured data transfer(UDT)
All the DS0 time slots are allocated.
This type of port supports following
features:
* intended to emulate point-to-point
DS1 or E1 circuit.
* Synchronous and Asynchronous timing
framingOnVcDisconnect : similar to unstructured during normal
operation. In case of channel failure
line data will be looped back towards
line.
strau : only one DS0 time slot is allocated.
The value strau(4) value is not supported in
CESM-8T1/E1 or CESM-T3E3.
CESM-T3E3 card supports value unstructured(2) only. |
| ciscoWanCesPortCompliance | 1.3.6.1.4.1.351.150.40.2.2.1 | | | The compliance statement for objects related
to CES Logical Ports. |
| ciscoWanCesPortConfGroup | 1.3.6.1.4.1.351.150.40.2.1.2 | | | The collection of objects which are used to represent
Circuit Emulation Service Port information. |
| ciscoWanCesPortDs0InDs1Group | 1.3.6.1.4.1.351.150.40.2.1.3 | | | The collection of objects related to information
on DS0 time slots used in each DS1 line. |
| ciscoWanCesPortMIB | 1.3.6.1.4.1.351.150.40 | | | The MIB module to configure the Circuit Emulation
Service(CES) ports. |
| ciscoWanCesPortMIBCompliances | 1.3.6.1.4.1.351.150.40.2.2 | | | |
| ciscoWanCesPortMIBConformance | 1.3.6.1.4.1.351.150.40.2 | | | |
| ciscoWanCesPortMIBGroups | 1.3.6.1.4.1.351.150.40.2.1 | | | |
| ciscoWanCesPortsUsedGroup | 1.3.6.1.4.1.351.150.40.2.1.1 | | | The collection of objects which are
applicable for general information about
logical ports. |
