| OID symbolic | OID numeric | Type | Access | Description |
|---|
| ciscoMobilityTapMIB | 1.3.6.1.4.1.9.9.672 | | | This module manages Cisco's intercept feature for
Mobility Gateway Products.
This MIB is used along with CISCO-TAP2-MIB MIB to
intercept Mobility Gateway traffic. CISCO-TAP2-MIB MIB
along with specific filter MIBs like this MIB replace
the CISCO-TAP-MIB MIB.
To create a Mobility intercept, an entry
cmtapStreamEntry is created which contains the filter
details. An entry cTap2StreamEntry of CISCO-TAP2-MIB is
created which is the common stream information for all
kinds of intercepts and type of the specific stream is
set to 'mobility' in this entry. |
| ciscoMobilityTapMIBNotifs | 1.3.6.1.4.1.9.9.672.0 | | | |
| ciscoMobilityTapMIBObjects | 1.3.6.1.4.1.9.9.672.1 | | | |
| cmtapStreamGroup | 1.3.6.1.4.1.9.9.672.1.1 | | | |
| BIT cmtapStreamCapabilities | 1.3.6.1.4.1.9.9.672.1.1.1 | Bits | read-only | This object indicates the Mobility Gateway intercept
features that are implemented by this device and are
manageable through this MIB.
tapEnable: set if table entries with
cTap2StreamInterceptEnable set to
'false' are used to pre-screen packets
for intercept; otherwise these entries
are ignored.
interface: SNMP ifIndex Value may be used to
select interception of all data
crossing an interface or set of
interfaces.
nonvolatileStorage: The cmTapStreamTable supports the
ability to store rows in nonvolatile
memory.
calledSubscriberID: The cmtapStreamCalledSubscriberID can
be used to specify intercepts.
Otherwise, this field is disabled.
msid: A Mobile Subscriber Identity (MSID) can
be used in the ID strings to specify
intercepts.
imsi: An International Mobile Subscriber
Identity (IMSI) number can be used ID
strings to specify intercepts.
nai: A Network Access Identifier (NAI) can
be used in the ID strings to specify
intercepts.
esn: An Electronic Serial Number (ESN) can
be used in the ID strings to specify
intercepts.
servedMdn: Vendor specific attribute Served-Mobile Directory
Number(MDN) can be used in the ID strings
to specify intercepts. |
| cmtapStreamTable | 1.3.6.1.4.1.9.9.672.1.1.2 | | not-accessible | The Mobility Stream Table lists the data streams to be
intercepted. The same data stream may be required by multiple
taps.
This essentially provides options for packet selection, only
some of which might be used. For example, if all the traffic to
or from a subscriber is to be intercepted, one would configure
an entry listing SubscriberID along with the SubscriberIDType
corresponding to the stream that one wishes to intercept.
The first index indicates which Mediation Device the
intercepted traffic will be diverted to. The second index,
which indicates the specific intercept stream, permits multiple
classifiers to be used together. For example, an IP stream
and a Mobility stream could both be listed in their respective
tables, yet still correspond to the same Mediation Device
entry.
Entries are added to this table via cmtapStreamStatus in
accordance with the RowStatus convention. |
| cmtapStreamEntry | 1.3.6.1.4.1.9.9.672.1.1.2.1 | | not-accessible | A stream entry indicates a single data stream to be
intercepted to a Mediation Device. Many selected data
streams may go to the same application interface and many
application interfaces are supported. |
| CMT cmtapStreamCalledSubscriberIDType | 1.3.6.1.4.1.9.9.672.1.1.2.1.1 | CmtapSubscriberIDType | read-create | Identifies the type of address that is stored in the
cmtapStreamCalledSubscriberID string. |
| CMT cmtapStreamCalledSubscriberID | 1.3.6.1.4.1.9.9.672.1.1.2.1.2 | CmtapSubscriberID | read-create | A string used to identify the party being contacted.
The type of this identification is determined by the
cmtapStreamCalledSubscriberIDType object. |
| CMT cmtapStreamSubscriberIDType | 1.3.6.1.4.1.9.9.672.1.1.2.1.3 | CmtapSubscriberIDType | read-create | Identifies the type of address that is stored in the
cmtapStreamSubscriberID string. |
| CMT cmtapStreamSubscriberID | 1.3.6.1.4.1.9.9.672.1.1.2.1.4 | CmtapSubscriberID | read-create | A string used to identify the subscriber to tap.
The type of this indentification is determined by the
cmtapStreamSubscriberIDType object. |
| STO cmtapStreamStorageType | 1.3.6.1.4.1.9.9.672.1.1.2.1.5 | StorageType | read-create | This object specifies the storage type of this conceptual row.
If it is set to 'nonVolatile', this entry can be saved into
non-volatile memory. |
| ROW cmtapStreamStatus | 1.3.6.1.4.1.9.9.672.1.1.2.1.6 | RowStatus | read-create | The status of this conceptual row. This object manages
creation, modification, and deletion of rows in this table.
When any field must be changed, cmtapStreamStatus must be
first set to 'notInService'. |
| NUM cmtapStreamLIIdentifier | 1.3.6.1.4.1.9.9.672.1.1.2.1.7 | CmtapLawfulInterceptID | read-create | This object is an identifier assigned by a Law Enforcement
Agency (LEA) to facilitate LI operations as defined in 3GPP TS
33.108 v8.7.0 standards document. |
| T/F cmtapStreamLocationInfo | 1.3.6.1.4.1.9.9.672.1.1.2.1.8 | TruthValue | read-create | This object indicates, if the userLocationInfo object should be
included in the Intercept Related Information (IRI) messages
sent by the gateway to mediation gateway(s) for interception
taps.
The userLocationInfo is defined as part of the IRI messages in
3GPP 33.108 v8.7.0 standards document. |
| INT cmtapStreamInterceptType | 1.3.6.1.4.1.9.9.672.1.1.2.1.9 | INTEGER | read-create | This object indicates the intercept type of the tapped stream.
The tap can be provisioned to intercept control messages (IRI)
from the tapped stream, the payload (CC) messages from the
tapped stream or both. The format of these messages in defined
in 3GPP TS 33.108 v8.7.0 standards document.
ccOnly(1) - Content of communication interception only.
iriOnly(2) - Intercept Related Information only.
both(3) - Intercept both: CC and IRI. |
| ciscoMobilityTapMIBConform | 1.3.6.1.4.1.9.9.672.2 | | | |
| ciscoMobilityTapMIBCompliances | 1.3.6.1.4.1.9.9.672.2.1 | | | |
| ciscoMobilityTapMIBCompliance | 1.3.6.1.4.1.9.9.672.2.1.1 | | | The compliance statement for entities which implement the
Cisco Intercept MIB for Mobility Gateways |
| ciscoMobilityTapMIBComplianceRev01 | 1.3.6.1.4.1.9.9.672.2.1.2 | | | The compliance statement for entities which implement the Cisco
Intercept MIB for Mobility Gateways. |
| ciscoMobilityTapMIBGroups | 1.3.6.1.4.1.9.9.672.2.2 | | | |
| ciscoMobilityTapCapabilityGroup | 1.3.6.1.4.1.9.9.672.2.2.1 | | | A collection of objects which provide Mobility Gateway
capabilities for the system. |
| ciscoMobilityTapStreamGroup | 1.3.6.1.4.1.9.9.672.2.2.2 | | | A collection of objects which provide information about
the stream from which we wish to intercept packets. |
| ciscoMobilityTapStreamGroupSup1 | 1.3.6.1.4.1.9.9.672.2.2.3 | | | A collection of objects which provide additional information
about the stream from which we wish to intercept packets. |
