CISCO-MEGACO-EXT-MIB :: cmedxCallRenotifInterval

MIB Reference — IPNetwork Monitor · Updated September 14, 2026

All MIBsCISCO-MEGACO-EXT-MIBcmedxCallRenotifInterval

cmedxCallRenotifInterval

Module: CISCO-MEGACO-EXT-MIB

OID (symbolic): CISCO-MEGACO-EXT-MIB::cmedxCallRenotifInterval

OID (numeric): 1.3.6.1.4.1.9.10.104.1.1.4.1.2

Node type: OBJECT-TYPE

Type: Unsigned32

Access: read-write

Description: This object specifies the interval of the congestion renotification from the media gateway to the MGC.

In the event of congestion on the Media Gateway, gateway generates an event towards MGC. Using this message, MG requests percentage reduction in the rate of calls that MGC is attempting towards MG. After sending this indication, MG starts a timer based on 'cmedxCallRenotifInterval'. At this timer expires, MG will re-send the message to MGC indicating that it is still in congested state. If MGC does not receive another notification, MGC will resume to the original call rate. If MGC requires re-notifications, it is user's responsibility to set the value of this MIB object on MG appropriately. The value of this object should be set such that it factors into the network delay and re-notification timer (similar to this MIB object) configured on MGC. The zero means MGC does not require re-notifications, MGC will keep CallReduceRate until receive another notification from the Media Gateway.

What is cmedxCallRenotifInterval?

This read-write object configures the interval at which a media gateway re-sends congestion notification messages to the MGC (Media Gateway Controller), used when requesting a percentage reduction in incoming call rate due to congestion.

Examples

Walk all instances (SNMPv2c):

snmpwalk -v2c -c public <target> 1.3.6.1.4.1.9.10.104.1.1.4.1.2
snmpwalk -v2c -c public <target> CISCO-MEGACO-EXT-MIB::cmedxCallRenotifInterval

Get a specific instance (index 1):

snmpget -v2c -c public <target> 1.3.6.1.4.1.9.10.104.1.1.4.1.2.1
snmpget -v2c -c public <target> CISCO-MEGACO-EXT-MIB::cmedxCallRenotifInterval.1

Set instance 1 (SNMPv2c):

snmpset -v2c -c private <target> 1.3.6.1.4.1.9.10.104.1.1.4.1.2.1 i <value>

Start monitoring Cisco media gateway/media gateway controller (H.248/Megaco) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the CISCO-MEGACO-EXT-MIB::cmedxCallRenotifInterval OID value, configure state conditions and alerts, and monitor any Cisco media gateway/media gateway controller (H.248/Megaco) from a single console.

OID Breakdown

Upper-level ancestors (8 from the standard OID tree / other modules)
Numeric OIDNameModule
1isoLANART-AGENT
1.3orgAirPair-MIB
1.3.6dodAirPair-MIB
1.3.6.1internetAirPair-MIB
1.3.6.1.4privateAirPair-MIB
1.3.6.1.4.1enterprisesAirPair-MIB
1.3.6.1.4.1.9ciscoCAT2600-MIB
1.3.6.1.4.1.9.10ciscoExperimentCISCO-SMI
Numeric OIDNameModule
1.3.6.1.4.1.9.10.104ciscoMegacoExtMIBCISCO-MEGACO-EXT-MIB
1.3.6.1.4.1.9.10.104.1ciscoMegacoExtMIBObjectsCISCO-MEGACO-EXT-MIB
1.3.6.1.4.1.9.10.104.1.1cmedxConfigCISCO-MEGACO-EXT-MIB
1.3.6.1.4.1.9.10.104.1.1.4cmedxCallReduceControlTableCISCO-MEGACO-EXT-MIB
1.3.6.1.4.1.9.10.104.1.1.4.1cmedxCallReduceControlEntryCISCO-MEGACO-EXT-MIB
1.3.6.1.4.1.9.10.104.1.1.4.1.2cmedxCallRenotifIntervalCISCO-MEGACO-EXT-MIB