CISCO-LWAPP-MESH-STATS-MIB

MIB Reference — IPNetwork Monitor · Updated September 09, 2026

All MIBsCISCO-LWAPP-MESH-STATS-MIB

Organization: Cisco Systems Inc.

Last Updated: 2017-04-23

Category: Wireless/WiFi

Description: Provides traffic and link quality statistics for Cisco LWAPP wireless mesh backhaul connections.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-LWAPP-MESH-STATS-MIB?

CISCO-LWAPP-MESH-STATS-MIB is a Cisco module providing traffic and link-quality statistics for LWAPP-based wireless mesh backhaul connections, implemented on Central Controllers (wireless LAN controllers) that terminate LWAPP tunnels from mesh access points (RAP/MAP). It exposes per-mesh-node statistics covering malformed and poor-SNR neighbor packets, excluded packets, neighbor request/response counts, parent-change events, and association/backhaul counts. It is primarily a wireless-mesh performance and fault-monitoring module — tracking software-level radio-link health such as link quality (poor-SNR packet counts) and mesh topology stability (parent changes) — useful for diagnosing a degraded mesh backhaul rather than physical chassis hardware. It depends on the Cisco LWAPP architecture and is meant to be used alongside Cisco's broader LWAPP/CAPWAP access-point and controller MIBs for full wireless mesh visibility. CISCO-LWAPP-MESH-STATS-MIB SNMP monitoring is deployed on Cisco wireless LAN controllers managing outdoor or mesh Wi-Fi deployments where access points backhaul over wireless mesh links.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-LWAPP-MESH-STATS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • Cisco wireless LAN controllers with LWAPP mesh access points (RAP/MAP)

Monitoring Examples

An admin would poll clMeshNodeStatsTable, keyed by mesh node, watching clMeshNodePoorNeighSnrPkts and clMeshNodeMalformedNeighPkts for signs of a degrading RF backhaul link, and clMeshNodeParentChanges for topology instability. A rising clMeshNodeSecBackhaulCount alongside frequent parent changes would indicate a mesh access point repeatedly failing over to its secondary backhaul path due to poor link quality.

What Can Be Monitored

  • mesh neighbor packet errors
  • poor-SNR neighbor packets
  • mesh parent change count
  • secondary backhaul usage count
  • mesh association count
  • neighbor request/response counts
Imported Objects

From CISCO-LWAPP-AP-MIB

cLApDot11RadioRoleOBJECT-TYPE
cLApNameOBJECT-TYPE
cLApSysMacAddressOBJECT-TYPE

From CISCO-LWAPP-MESH-MIB

clMeshNeighborMacAddressOBJECT-TYPE
clMeshNodeBackhaulOBJECT-TYPE

From CISCO-SMI

ciscoMgmtOBJECT-IDENTITY

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TimeInterval
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using clMeshNodeMalformedNeighPkts OID:

Select a Cisco wireless LAN controllers with LWAPP mesh access point (RAP/MAP) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type clMeshNodeMalformedNeighPkts into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This object represents total number of packets received from neighbor mesh nodes which could not be decoded. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in packets), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs

RFC description

Cisco SNMP MIB for wireless mesh network statistics on LWAPP (Lightweight Access Point Protocol) controllers. Tracks mesh node packets, queue statistics, and security negotiations between mesh nodes in centralized wireless deployments.

Start monitoring Cisco wireless LAN controllers with LWAPP mesh access points (RAP/MAP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-LWAPP-MESH-STATS-MIB