MOXA-W2x50A-MIB

All MIBs › MOXA-W2x50A-MIB

Organization: Moxa Inc.

Last Updated: 2015-07-17

Category: Industrial Networking, Wireless/WiFi

Description: Manages Moxa W2150A/W2250A industrial wireless device configuration and link status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is MOXA-W2x50A-MIB?

MOXA-W2x50A-MIB is a vendor-specific module for Moxa's NPort W2150A/W2250A wireless serial device servers, which provide industrial wireless connectivity for serial equipment. The visible structure exposes a management subtree (swMgmt) covering wireless link and serial port configuration. Monitoring emphasis is on wireless link and serial port health: signal/connection status for the wireless link and operational state of the attached serial port, alongside device software status. It follows the same Moxa device-server management conventions used across other NPort product lines. Typical deployment is industrial wireless networks where serial equipment is connected via Moxa W2150A/W2250A wireless serial servers, which administrators can load into a MOXA-W2x50A-MIB MIB Browser to inspect available objects directly.

IPNetwork Monitor allows you to monitor SNMP objects defined in MOXA-W2x50A-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Moxa NPort W2150A/W2250A industrial wireless device server

Monitoring Examples

An admin polls objects under the swMgmt subtree to check wireless link status and serial port state on a W2150A/W2250A unit, watching for signal dropouts or serial port errors. Because only the top-level swMgmt node is visible in this excerpt, specific wireless/RF leaf object names aren't confirmed here.

What Can Be Monitored

wireless link status
serial port status
device configuration
signal/connection quality

Imported Objects

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
moxa	1.3.6.1.4.1.8691
nport	1.3.6.1.4.1.8691.2
w2x50A	1.3.6.1.4.1.8691.2.13			The MIB module for Moxa NPort W2x50A series specific information.
swMgmt	1.3.6.1.4.1.8691.2.13.1
overview	1.3.6.1.4.1.8691.2.13.1.1
STR modelName	1.3.6.1.4.1.8691.2.13.1.1.1	DisplayString	read-only	The model name of the NPort. The possible values of this parameter are: 'NPort W2x50A' for NPort W2x50A.
INT serialNumber	1.3.6.1.4.1.8691.2.13.1.1.2	INTEGER	read-only	The serial number of the NPort. Every NPort W2x50A series device server is assigned a unique serial number before it is shipped.
STR firmwareVersion	1.3.6.1.4.1.8691.2.13.1.1.3	DisplayString	read-only	The version of the firmware currently running on the NPort.
MAC ethMacAddress	1.3.6.1.4.1.8691.2.13.1.1.5	MacAddress	read-only	The MAC address of the NPort's Ethernet interface.
MAC wlanMacAddress	1.3.6.1.4.1.8691.2.13.1.1.7	MacAddress	read-only	The MAC address of the NPort's WLAN interface.
STR wlanSSID	1.3.6.1.4.1.8691.2.13.1.1.8	DisplayString	read-only	The SSID of WLAN.
STR wlanNetworkType	1.3.6.1.4.1.8691.2.13.1.1.9	DisplayString	read-only	Network Type of Wireless LAN. The possible values are 'Infrastrcture Mode' and 'Ad-hoc Mode'
STR wlanSecurityMode	1.3.6.1.4.1.8691.2.13.1.1.10	DisplayString	read-only	Security mode of Wireless LAN. The possible values are 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK'
STR wlanRFType	1.3.6.1.4.1.8691.2.13.1.1.11	DisplayString	read-only	RF type of Wireless LAN. The possible values are 'Auto', '802.11b', '802.11g'
STR wlanCountryCode	1.3.6.1.4.1.8691.2.13.1.1.12	DisplayString	read-only	WLAN country code
STR wlanFastRoaming	1.3.6.1.4.1.8691.2.13.1.1.13	DisplayString	read-only	Fast roaming state
STR activeNetworkPort	1.3.6.1.4.1.8691.2.13.1.1.14	DisplayString	read-only	Current active network port. The possible values are 'WLAN', 'Ethernet'
STR upTime	1.3.6.1.4.1.8691.2.13.1.1.15	DisplayString	read-only	The time (in human-readable notation) since the system was last re-initialized.
STR serialPort1	1.3.6.1.4.1.8691.2.13.1.1.16	DisplayString	read-only	View NPort's serial port 1 setting.
STR serialPort2	1.3.6.1.4.1.8691.2.13.1.1.17	DisplayString	read-only	View NPort's serial port 2 setting.
basicSetting	1.3.6.1.4.1.8691.2.13.1.2
serverSetting	1.3.6.1.4.1.8691.2.13.1.2.1
STR serverName	1.3.6.1.4.1.8691.2.13.1.2.1.1	DisplayString	read-write	A text string used to identify the NPort.
STR serverLocation	1.3.6.1.4.1.8691.2.13.1.2.1.2	DisplayString	read-write	A text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers.
timeSetting	1.3.6.1.4.1.8691.2.13.1.2.2
INT timeZone	1.3.6.1.4.1.8691.2.13.1.2.2.1	INTEGER	read-write	The time-zone index of the NPort.
STR localTime	1.3.6.1.4.1.8691.2.13.1.2.2.2	DisplayString	read-write	The system time in the following format yyyy/mm/dd hh:mm:ss
STR timeServer	1.3.6.1.4.1.8691.2.13.1.2.2.3	DisplayString	read-write	The NPort W2x50A series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort W2x50A series device server is configured with the correct Time server address, it will request time information from the Time server every 10 minutes.
networkSetting	1.3.6.1.4.1.8691.2.13.1.3
generalSetting	1.3.6.1.4.1.8691.2.13.1.3.1
IP dnsServer1IpAddr	1.3.6.1.4.1.8691.2.13.1.3.1.1	IpAddress	read-write	The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website's correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
IP dnsServer2IpAddr	1.3.6.1.4.1.8691.2.13.1.3.1.2	IpAddress	read-write	The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website's correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
ethernetSetting	1.3.6.1.4.1.8691.2.13.1.3.2
INT ethIpConfiguration	1.3.6.1.4.1.8691.2.13.1.3.2.1	INTEGER	read-write	The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP.
IP ethIPAddress	1.3.6.1.4.1.8691.2.13.1.3.2.2	IpAddress	read-write	An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
IP ethNetMask	1.3.6.1.4.1.8691.2.13.1.3.2.3	IpAddress	read-write	A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort W2x50A series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort W2x50A series device server, a connection is established directly from the NPort W2x50A series device server. Otherwise, the connection is established through the given default gateway.
IP ethDefaultGateway	1.3.6.1.4.1.8691.2.13.1.3.2.4	IpAddress	read-write	A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort W2x50A series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
INT ethBridgeMode	1.3.6.1.4.1.8691.2.13.1.3.2.5	INTEGER	read-write	Enable or disable the bridge function.
wlanSetting	1.3.6.1.4.1.8691.2.13.1.3.3
INT wlanIpConfiguration	1.3.6.1.4.1.8691.2.13.1.3.3.1	INTEGER	read-write	The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP.
IP wlanIPAddress	1.3.6.1.4.1.8691.2.13.1.3.3.2	IpAddress	read-write	An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
IP wlanNetMask	1.3.6.1.4.1.8691.2.13.1.3.3.3	IpAddress	read-write	A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort W2x50A series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort W2x50A series device server, a connection is established directly from the NPort W2x50A series device server. Otherwise, the connection is established through the given default gateway.
IP wlanDefaultGateway	1.3.6.1.4.1.8691.2.13.1.3.3.4	IpAddress	read-write	A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort W2x50A series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
profileSetting	1.3.6.1.4.1.8691.2.13.1.3.4
INT networkType	1.3.6.1.4.1.8691.2.13.1.3.4.1	INTEGER	read-write	Select WLAN network type.
adhocProfile	1.3.6.1.4.1.8691.2.13.1.3.4.2
adhocGeneralSetting	1.3.6.1.4.1.8691.2.13.1.3.4.2.1
STR adhocProfileName	1.3.6.1.4.1.8691.2.13.1.3.4.2.1.1	DisplayString	read-write	Assign profile name.
INT adhocRFType	1.3.6.1.4.1.8691.2.13.1.3.4.2.1.2	INTEGER	read-write	Select WLAN network type.
STR adhocWlanSSID	1.3.6.1.4.1.8691.2.13.1.3.4.2.1.3	DisplayString	read-write	Set WLAN SSID
INT adhocChannel	1.3.6.1.4.1.8691.2.13.1.3.4.2.1.4	INTEGER	read-write	Display currently used channel. When in Ad-Hoc mode, this value can be set. mode region possible channel ====================================== 802.11b_g : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
adhocSecuritySetting	1.3.6.1.4.1.8691.2.13.1.3.4.2.2
INT adhocAuthentication	1.3.6.1.4.1.8691.2.13.1.3.4.2.2.1	INTEGER	read-only	Wireless LAN autentication type.
INT adhocEncryption	1.3.6.1.4.1.8691.2.13.1.3.4.2.2.2	INTEGER	read-write	Set encryption type.
INT adhocWepKeyLength	1.3.6.1.4.1.8691.2.13.1.3.4.2.2.3	INTEGER	read-write	WEP key length.
INT adhocWepKeyIndex	1.3.6.1.4.1.8691.2.13.1.3.4.2.2.4	INTEGER	read-write	WEP key index 1~4.
STR adhocWepKeyPassphrase	1.3.6.1.4.1.8691.2.13.1.3.4.2.2.5	DisplayString	write-only	WEP key passphrase.
INT adhocWepKeyFormat	1.3.6.1.4.1.8691.2.13.1.3.4.2.2.6	INTEGER	read-write	WEP key format.
infrastructureProfile	1.3.6.1.4.1.8691.2.13.1.3.4.3
infraGeneralSetting	1.3.6.1.4.1.8691.2.13.1.3.4.3.1
infraGeneralSettingTable	1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1		not-accessible	WLAN profile general setting table.
infraGeneralSettingEntry	1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1		not-accessible	WLAN profile general setting entry.
INT profileIndex	1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.1	INTEGER	read-only	The profile index
STR profileName	1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.2	DisplayString	read-write	Assign profile name.
INT profileRFType	1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.3	INTEGER	read-write	Select WLAN network type.
STR profileWlanSSID	1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.4	DisplayString	read-write	Set WLAN SSID
securitySetting	1.3.6.1.4.1.8691.2.13.1.3.4.3.2
securitySettingTable	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1		not-accessible	WLAN profile security setting table.
securitySettingEntry	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1		not-accessible	WLAN profile security setting entry.
INT authentication	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.1	INTEGER	read-write	Wireless LAN autentication type.
INT encryption	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.2	INTEGER	read-write	Set encryption type. Selection rule is as following. authentication selectable encryption ============== ===================== open-system(0) disable(0), wep(1) shared-key(1) wep(1) wpa(2), wpa-psk(3) tkip(2), aes-ccmp(3) wpa2(4), wpa2-psk(5) tkip(2), aes-ccmp(3)
INT wepKeyLength	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.3	INTEGER	read-write	WEP key length.
INT wepKeyIndex	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.4	INTEGER	read-write	WEP key index 1~4.
STR wepKeyPassphrase	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.5	DisplayString	write-only	WEP key passphrase.
INT wepKeyFormat	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.6	INTEGER	read-write	WEP key format.
INT eapMethod	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.12	INTEGER	read-write	EAP method for WPA and WPA2 authentication.
INT tunneledAuth	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.13	INTEGER	read-write	Set tunneled authentication protocol when PEAP/TTLS is selected as EAP method. EAP method selectable tunneled authentication ========== ================================== peap(1) gtc(0), md5(1), mschapv2(5) ttls(2) pap(2), chap(3), mschap(4), mschapv2(5), eap-mschapv2(8), eap-gtc(9), eap-md5(10)
STR wpaUsername	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.14	DisplayString	read-write	WPA username for WPA and WPA2 authentication.
STR wpaAnonymousUsername	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.16	DisplayString	read-write	Anonymous username needed when TTLS is selected as EAP method.
INT verifyServerCert	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.17	INTEGER	read-write	The setting of verify server certificate.
INT trustedServerCert	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.18	INTEGER	read-only	Display whether or not trusted server certificate is installed.
INT userCert	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.19	INTEGER	read-only	Display whether or not user certificate is installed.
INT userPrivateKey	1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.20	INTEGER	read-only	Display whether or not user private key is installed.
INT fastRoamingSetting	1.3.6.1.4.1.8691.2.13.1.3.4.3.3	INTEGER	read-write	The setting of fast roaming.
INT fastRoamingScanChannels1	1.3.6.1.4.1.8691.2.13.1.3.4.3.4	INTEGER	read-write	The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11a, 802.11a_n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11b_g, 802.11b_g_n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
INT fastRoamingScanChannels2	1.3.6.1.4.1.8691.2.13.1.3.4.3.5	INTEGER	read-write	The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11a, 802.11a_n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11b_g, 802.11b_g_n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
INT fastRoamingScanChannels3	1.3.6.1.4.1.8691.2.13.1.3.4.3.6	INTEGER	read-write	The scan channels of fast roaming. 0 represents 'N/A' ====================================================== Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11a, 802.11a_n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 802.11b_g, 802.11b_g_n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13
INT fastRoamingThreshold	1.3.6.1.4.1.8691.2.13.1.3.4.3.7	INTEGER	read-write	Roaming threshold of fast roaming
INT fastRoamingDifference	1.3.6.1.4.1.8691.2.13.1.3.4.3.8	INTEGER	read-write	Roaming difference of fast roaming
wlanLogSetting	1.3.6.1.4.1.8691.2.13.1.3.5
INT wlanLogEnable	1.3.6.1.4.1.8691.2.13.1.3.5.1	INTEGER	read-write	Enable or disable WLAN log
advancedSetting	1.3.6.1.4.1.8691.2.13.1.3.6
INT gratuitousArp	1.3.6.1.4.1.8691.2.13.1.3.6.1	INTEGER	read-write	Enable or disable the gratuitous ARP function. For some applications, users need the NPort W2x50A series device server to send broadcast packets to update the ARP table on the server. If the customer enables this function and sets the send period, the NPort W2x50A series device server will send broadcast packets periodically.
INT gratuitousArpSendPeriod	1.3.6.1.4.1.8691.2.13.1.3.6.2	INTEGER	read-write	The send period of the gratuitous ARP function. Range: 10 ~ 1000 sec.
STR gratuitousArpIpAddress1	1.3.6.1.4.1.8691.2.13.1.3.6.3	DisplayString	read-write	The IP address of the static gratuitous ARP.
STR gratuitousArpMacAddress1	1.3.6.1.4.1.8691.2.13.1.3.6.4	DisplayString	read-write	The MAC address of the static gratuitous ARP.
STR gratuitousArpIpAddress2	1.3.6.1.4.1.8691.2.13.1.3.6.5	DisplayString	read-write	The IP address of the static gratuitous ARP.
STR gratuitousArpMacAddress2	1.3.6.1.4.1.8691.2.13.1.3.6.6	DisplayString	read-write	The MAC address of the static gratuitous ARP.
STR gratuitousArpIpAddress3	1.3.6.1.4.1.8691.2.13.1.3.6.7	DisplayString	read-write	The IP address of the static gratuitous ARP.
STR gratuitousArpMacAddress3	1.3.6.1.4.1.8691.2.13.1.3.6.8	DisplayString	read-write	The MAC address of the static gratuitous ARP.
STR gratuitousArpIpAddress4	1.3.6.1.4.1.8691.2.13.1.3.6.9	DisplayString	read-write	The IP address of the static gratuitous ARP.
STR gratuitousArpMacAddress4	1.3.6.1.4.1.8691.2.13.1.3.6.10	DisplayString	read-write	The MAC address of the static gratuitous ARP.
portSetting	1.3.6.1.4.1.8691.2.13.1.4
opModeSetting	1.3.6.1.4.1.8691.2.13.1.4.1
opMode	1.3.6.1.4.1.8691.2.13.1.4.1.1
opModePortTable	1.3.6.1.4.1.8691.2.13.1.4.1.1.1		not-accessible	The serial ports' operation mode table.
opModePortEntry	1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1		not-accessible	The serial port's operation mode entry.
INT portIndex	1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.1	INTEGER	read-only	The serial port index.
INT portMode	1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.2	INTEGER	read-write	The operation mode of the serial port. Note that changing this setting may also change the application.
opModeParam	1.3.6.1.4.1.8691.2.13.1.4.1.2
realCOM	1.3.6.1.4.1.8691.2.13.1.4.1.2.1
realCOMTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1		not-accessible	The Real COM mode table.
realCOMEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1		not-accessible	The Real COM mode entry.
INT realCOMTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another Real COM driver Connection.
INT realCOMMaxConnection	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.2	INTEGER	read-write	Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort W2x50A series device server, and the Real COM driver on that host will have full control over the port. Max. connection = 1: Allows only a single host's Real COM driver to open the specific NPort W2x50A series device server's serial port. Max connection = 2 to 8: Allows 2 to 8 hosts' Real COM drivers to open the specific NPort W2x50A series device server's serial port, at the same time. When multiple hosts' Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of getting the settings from your application program (AP).
INT realCOMIgnoreJammedIp	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.3	INTEGER	read-write	Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
INT realCOMAllowDriverControl	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.4	INTEGER	read-write	If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort W2x50A series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
INT realCOMConnectionDownRTS	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.5	INTEGER	read-write	For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort W2x50A series device server. If this setting is set to 'always low,' RTS will change its state to low if the Ethernet link is off.
INT realCOMConnectionDownDTR	1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.6	INTEGER	read-write	For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort W2x50A series device server. If this setting is set to 'always low,' DTR will change its state to low if the Ethernet link is off.
rfc2217	1.3.6.1.4.1.8691.2.13.1.4.1.2.2
rfc2217Table	1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1		not-accessible	The RFC2217 mode table.
rfc2217Entry	1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1		not-accessible	The RFC2217 mode entry.
INT rfc2217TcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP Connection.
INT rfc2217TcpPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.2	INTEGER	read-write	TCP server port of RFC2217.
tcpServer	1.3.6.1.4.1.8691.2.13.1.4.1.2.3
tcpServerTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1		not-accessible	The TCP server mode table.
tcpServerEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1		not-accessible	The TCP server mode entry.
INT tcpServerTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP Connection.
INT tcpServerInactivityTime	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.2	INTEGER	read-write	0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort W2x50A series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP connection.
INT tcpServerMaxConnection	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.3	INTEGER	read-write	Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort W2x50A series device server, and the TCP server driver on that host will have full control over the port. Max. connection 1: Allows only a single host's to connect specific NPort W2x50A series device Max connection 2 to 8: Allows 2 to 8 hosts' to conncect NPort W2x50A series device at the same time.
INT tcpServerIgnoreJammedIp	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.4	INTEGER	read-write	Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
INT tcpServerAllowDriverControl	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.5	INTEGER	read-write	If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort W2x50A series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
INT tcpServerTcpPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.6	INTEGER	read-write	The 'TCP port' is the TCP port that the NPort W2x50A series device server uses to listen to connections, and that other devices must use to contact the NPort W2x50A series device server.
INT tcpServerCmdPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.7	INTEGER	read-write	The 'Command port' is a TCP port used to listen for SSDK commands from the host. In order to prevent a TCP port conflict with other applications, the user can set the Command port to another port if needed.
INT tcpServerConnectionDownRTS	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.8	INTEGER	read-write	For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort W2x50A series device server. If this setting is set to 'goes low,' RTS will change the state to low if the Ethernet link is off.
INT tcpServerConnectionDownDTR	1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.9	INTEGER	read-write	For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort W2x50A series device server. If this setting is set to 'goes low,' DTR will change the state to low if the Ethernet link is off.
tcpClient	1.3.6.1.4.1.8691.2.13.1.4.1.2.4
tcpClientTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1		not-accessible	The TCP client mode table.
tcpClientEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1		not-accessible	The TCP client mode entry.
INT tcpClientTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device client automatically closes the TCP connection if there is no TCP activity for the given time.
INT tcpClientInactivityTime	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.2	INTEGER	read-write	0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort W2x50A series device client automatically closes the TCP connection if there is no serial data activity for the given time.
INT tcpClientIgnoreJammedIp	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.3	INTEGER	read-write	Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
STR tcpClientDestinationAddress1	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.4	DisplayString	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
INT tcpClientDestinationPort1	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.5	INTEGER	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this TCP port number.
STR tcpClientDestinationAddress2	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.6	DisplayString	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
INT tcpClientDestinationPort2	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.7	INTEGER	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this TCP port number.
STR tcpClientDestinationAddress3	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.8	DisplayString	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
INT tcpClientDestinationPort3	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.9	INTEGER	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this port number.
STR tcpClientDestinationAddress4	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.10	DisplayString	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this IP address.
INT tcpClientDestinationPort4	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.11	INTEGER	read-write	The NPort W2x50A series device server can connect actively to a remote host that has this port number.
INT tcpClientDesignatedLocalPort1	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.12	INTEGER	read-write	The local TCP port used to connect actively to the remote host.
INT tcpClientDesignatedLocalPort2	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.13	INTEGER	read-write	The local TCP port used to connect actively to the remote host.
INT tcpClientDesignatedLocalPort3	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.14	INTEGER	read-write	The local TCP port used to connect actively to the remote host.
INT tcpClientDesignatedLocalPort4	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.15	INTEGER	read-write	The local TCP port used to connect actively to the remote host.
INT tcpClientConnectionControl	1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.16	INTEGER	read-write	Events that cause the TCP client to drop the connection.
udp	1.3.6.1.4.1.8691.2.13.1.4.1.2.5
udpTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1		not-accessible	The UDP mode table.
udpEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1		not-accessible	The UDP mode entry.
IP udpDestinationAddress1Begin	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.1	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress1End.
IP udpDestinationAddress1End	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.2	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress1Begin and this parameter.
INT udpDestinationPort1	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.3	INTEGER	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number.
IP udpDestinationAddress2Begin	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.4	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress2End.
IP udpDestinationAddress2End	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.5	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between udpDestinationAddress2Begin and this parameter.
INT udpDestinationPort2	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.6	INTEGER	read-write	The NPort W2x50A series device server can actively send UDP packets to the remote hosts that have this UDP port number.
IP udpDestinationAddress3Begin	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.7	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress3End.
IP udpDestinationAddress3End	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.8	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress3Begin and this parameter.
INT udpDestinationPort3	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.9	INTEGER	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number.
IP udpDestinationAddress4Begin	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.10	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and udpDestinationAddress4End.
IP udpDestinationAddress4End	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.11	IpAddress	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between udpDestinationAddress4Begin and this parameter.
INT udpDestinationPort4	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.12	INTEGER	read-write	The NPort W2x50A series device server can actively send UDP packets to remote hosts that have this UDP port number.
INT udpLocalListenPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.13	INTEGER	read-write	The UDP port that the NPort W2x50A series device server listens to and that other devices must use to contact the NPort W2x50A series device server.
pairConnectionMaster	1.3.6.1.4.1.8691.2.13.1.4.1.2.6
pairConnectionMasterTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1		not-accessible	The pair connection master mode table.
pairConnectionMasterEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1		not-accessible	The pair connection master mode entry.
INT pairConnectionMasterTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts connecting again.
STR pairConnectionMasterDestnationAddress	1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.2	DisplayString	read-write	IP address of pair connection slave.
INT pairConnectionMasterDestnationTcpPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.3	INTEGER	read-write	TCP port of pair connection slave.
pairConnectionSlave	1.3.6.1.4.1.8691.2.13.1.4.1.2.7
pairConnectionSlaveTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1		not-accessible	The pair connection slave mode table.
pairConnectionSlaveEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1		not-accessible	The pair connection slave mode entry.
INT pairConnectionSlaveTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort W2x50A series device server starts listening for another TCP Connection.
INT pairConnectionSlaveLocalTcpPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.2	INTEGER	read-write	TCP server port of pair connection slave.
ethernetModem	1.3.6.1.4.1.8691.2.13.1.4.1.2.8
ethernetModemTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1		not-accessible	The ethernet modem mode table.
ethernetModemEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1		not-accessible	The ethernet modem mode entry.
INT ethernetModemTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time.
INT ethernetModemLocalTcpPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.2	INTEGER	read-write	TCP server port of ethernet modem.
reverseTerminal	1.3.6.1.4.1.8691.2.13.1.4.1.2.9
reverseTerminalTable	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1		not-accessible	The reverse terminal mode table.
reverseTerminalEntry	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1		not-accessible	The reverse terminal mode entry.
INT reverseTerminalTcpAliveCheck	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.1	INTEGER	read-write	The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no TCP activity for the given time.
INT reverseTerminalInactivityTime	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.2	INTEGER	read-write	0 min: TCP connection is not closed when the serial line is idle. 0-99 min: The NPort W2x50A series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort W2x50P series device server starts listening for another TCP connection.
INT reverseTerminalTcpPort	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.3	INTEGER	read-write	Each of the NPort W2x50A series device server's serial ports are mapped to a TCP port.
INT reverseTerminalAuthenticationType	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.4	INTEGER	read-write	The reverse terminal authentication type.
INT reverseTerminalMapKeys	1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.5	INTEGER	read-write	If data received through NPort W2x50A series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the serial port with an added 1. 'carriage return + line feed' if you select the 'cr-lf' option (i.e., the cursor will jump to the next line, and return to the first character of the line) 2. 'carriage return' if you select the 'cr' option (i.e., the cursor will return to the first character of the line 3. 'line feed' if you select the 'lf' option. (i.e., the cursor will jump to the next line, but not move horizontally)
dataPacking	1.3.6.1.4.1.8691.2.13.1.4.1.3
dataPackingPortTable	1.3.6.1.4.1.8691.2.13.1.4.1.3.1		not-accessible	The Data Packing table.
dataPackingPortEntry	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1		not-accessible	The Data Packing entry.
INT portPacketLength	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.1	INTEGER	read-write	If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length can be configured from 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
INT portDelimiter1Enable	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.2	INTEGER	read-write	Enable the first delimiter character.
STR portDelimiter1	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.3	DisplayString	read-write	The first delimiter character, in hex decimal.
INT portDelimiter2Enable	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.4	INTEGER	read-write	Enable the second delimiter character.
STR portDelimiter2	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.5	DisplayString	read-write	The second delimiter character, in hex decimal.
INT portDelimiterProcess	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.6	INTEGER	read-write	'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterAddTwo') of data is received after receiving the Delimiter. 'stripDelimiter': When the delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining data is transmitted. 'doNothing': The data will be transmitted when the delimiter is received.
INT portForceTransmit	1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.7	INTEGER	read-write	0: Disable the force transmit timeout. 1 to 65535: Forces the NPort W2x50A series device server's TCP/IP protocol software to try to pack serial data received during the specified time into the same data frame.
comParamSetting	1.3.6.1.4.1.8691.2.13.1.4.2
comParamPortTable	1.3.6.1.4.1.8691.2.13.1.4.2.1		not-accessible	The Communication Parameters table.
comParamPortEntry	1.3.6.1.4.1.8691.2.13.1.4.2.1.1		not-accessible	The Communication Parameters entry.
STR portAlias	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.1	DisplayString	read-write	Port alias is included to allow easy identification of the serial devices that are connected to NPort W2x50A series device server's serial port.
INT portInterface	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.2	INTEGER	read-write	The serial interface that the port works on.
INT portBaudRate	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.3	INTEGER	read-write	The port's speed in bits per second. You can choose a standard baud rate by indexing.
INT portDataBits	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.4	INTEGER	read-write	The number of bits in a character for the port.
INT portStopBits	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.5	INTEGER	read-write	The number of stop bits for the port.
INT portParity	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.6	INTEGER	read-write	The parity bit for the port.
INT portFlowControl	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.7	INTEGER	read-write	The flow-control method for the port.
INT portFIFO	1.3.6.1.4.1.8691.2.13.1.4.2.1.1.8	INTEGER	read-write	Enable or disable the port's FIFO.
dataBuffering	1.3.6.1.4.1.8691.2.13.1.4.3
dataBufferingPortTable	1.3.6.1.4.1.8691.2.13.1.4.3.1		not-accessible	The Data Buffering table.
dataBufferingPortEntry	1.3.6.1.4.1.8691.2.13.1.4.3.1.1		not-accessible	The Data Buffering entry.
INT portBufferingEnable	1.3.6.1.4.1.8691.2.13.1.4.3.1.1.1	INTEGER	read-write	Enable off-line port buffering.
INT portSerialDataLoggingEnable	1.3.6.1.4.1.8691.2.13.1.4.3.1.1.2	INTEGER	read-write	Enable or disable serial data logging for the port.
sysManagement	1.3.6.1.4.1.8691.2.13.1.5
miscNetworkSettings	1.3.6.1.4.1.8691.2.13.1.5.1
accessibleIp	1.3.6.1.4.1.8691.2.13.1.5.1.1
INT enableAccessibleIpList	1.3.6.1.4.1.8691.2.13.1.5.1.1.1	INTEGER	read-write	Enable or disable the entire accessible IP list.
accessibleIpListTable	1.3.6.1.4.1.8691.2.13.1.5.1.1.2		not-accessible	Accessible IP List table.
accessibleIpListEntry	1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1		not-accessible	Accessible IP List entry.
INT accessibleIpListIndex	1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.1	INTEGER	read-only	Accessible IP List index.
INT activeAccessibleIpList	1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.2	INTEGER	read-write	Enable or disable this accessible IP entry.
IP accessibleIpListAddress	1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.3	IpAddress	read-write	Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address.
IP accessibleIpListNetmask	1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.4	IpAddress	read-write	Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts.
snmpAgentSettings	1.3.6.1.4.1.8691.2.13.1.5.1.2
INT snmpEnable	1.3.6.1.4.1.8691.2.13.1.5.1.2.1	INTEGER	read-write	Enable or disable SNMP agent.
STR snmpContactName	1.3.6.1.4.1.8691.2.13.1.5.1.2.2	DisplayString	read-write	The SNMP contact information usually includes an emergency contact name and telephone or pager number.
STR snmpLocation	1.3.6.1.4.1.8691.2.13.1.5.1.2.3	DisplayString	read-write	Specify the location string for SNMP agents, such as the NPort W2x50A series device server. This string is usually set to the street address where the NPort W2x50A series device server is physically located.
authenticationServer	1.3.6.1.4.1.8691.2.13.1.5.1.4
STR radiusServerIp	1.3.6.1.4.1.8691.2.13.1.5.1.4.1	DisplayString	read-write	The IP address or domain name of the RADIUS server.
INT udpPortAuthenticationServer	1.3.6.1.4.1.8691.2.13.1.5.1.4.3	INTEGER	read-write	The UDP port of the RADIUS server.
INT radiusAccounting	1.3.6.1.4.1.8691.2.13.1.5.1.4.4	INTEGER	read-write	Enable or disable RADIUS accounting.
sysLogSettings	1.3.6.1.4.1.8691.2.13.1.5.1.5
INT sysLocalLog	1.3.6.1.4.1.8691.2.13.1.5.1.5.1	INTEGER	read-write	System cold start, System warm start.
INT networkLocalLog	1.3.6.1.4.1.8691.2.13.1.5.1.5.2	INTEGER	read-write	DHCP/BOOTP get IP/renew, mail fail, NTP connect fail, IP conflict, network link down.
INT configLocalLog	1.3.6.1.4.1.8691.2.13.1.5.1.5.3	INTEGER	read-write	Login fail, IP changed, password changed, firmware upgrade, SSL certificate import, config export, wireless certificate import, serial data log export.
INT opModeLocalLog	1.3.6.1.4.1.8691.2.13.1.5.1.5.4	INTEGER	read-write	Connect, Disconnect, Restart.
autoWarningSettings	1.3.6.1.4.1.8691.2.13.1.5.2
eventSettings	1.3.6.1.4.1.8691.2.13.1.5.2.1
INT mailWarningColdStart	1.3.6.1.4.1.8691.2.13.1.5.2.1.1	INTEGER	read-write	Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort W2x50A series device server will automatically issue an auto warning message by e-mail after booting up.
INT mailWarningWarmStart	1.3.6.1.4.1.8691.2.13.1.5.2.1.2	INTEGER	read-write	Refers to restarting the NPort W2x50A without turning the power off. When performing a warm start, the NPort W2x50A series device server will automatically send an e-mail after rebooting.
INT mailWarningAuthFailure	1.3.6.1.4.1.8691.2.13.1.5.2.1.3	INTEGER	read-write	The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort W2x50A series device server will immediately send an e-mail.
INT mailWarningIpChanged	1.3.6.1.4.1.8691.2.13.1.5.2.1.4	INTEGER	read-write	The user has changed the NPort W2x50A series device server's IP address. When the IP address changes,the NPort W2x50A series device server will send an e-mail with the new IP address before it reboots. If the NPort W2x50A series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.
INT mailWarningPasswordChanged	1.3.6.1.4.1.8691.2.13.1.5.2.1.5	INTEGER	read-write	The user has changed the NPort W2x50A series device server's password. When the password changes, the NPort W2x50A series device server will send an e-mail with the password changed notice before it reboots. If the NPort W2x50A series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.
INT trapServerColdStart	1.3.6.1.4.1.8691.2.13.1.5.2.1.6	INTEGER	read-write	Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort W2x50A series device server will automatically issue an auto warning message by sending an SNMP trap after booting up.
INT trapServerWarmStart	1.3.6.1.4.1.8691.2.13.1.5.2.1.7	INTEGER	read-write	Refers to restarting the NPort W2x50A without turning the power off. When performing a warm start, the NPort W2x50A series device server will automatically send an SNMP trap after rebooting.
INT trapServerAuthFailure	1.3.6.1.4.1.8691.2.13.1.5.2.1.8	INTEGER	read-write	The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort W2x50A series device server will immediately send an SNMP trap.
serialEventSettings	1.3.6.1.4.1.8691.2.13.1.5.2.2
portEventSettingsTable	1.3.6.1.4.1.8691.2.13.1.5.2.2.1		not-accessible	Port Event Settings Table.
portEventSettingsEntry	1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1		not-accessible	Port Event Settings entry.
INT mailDCDchange	1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.1	INTEGER	read-write	A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort W2x50A series device server will immediately send an e-mail message.
INT trapDCDchange	1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.2	INTEGER	read-write	A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort W2x50A series device server will immediately send an SNMP trap.
INT mailDSRchange	1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.3	INTEGER	read-write	A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort W2x50A series device server will immediately send an e-mail message.
INT trapDSRchange	1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.4	INTEGER	read-write	A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort W2x50A series device server will immediately send an SNMP trap.
emailAlert	1.3.6.1.4.1.8691.2.13.1.5.2.3
STR emailWarningMailServer	1.3.6.1.4.1.8691.2.13.1.5.2.3.1	DisplayString	read-write	The e-mail server's IP address or domain name of the e-mail warning function.
INT emailRequiresAuthentication	1.3.6.1.4.1.8691.2.13.1.5.2.3.2	INTEGER	read-write	Set if the mail server requires user login.
STR emailWarningUserName	1.3.6.1.4.1.8691.2.13.1.5.2.3.3	DisplayString	read-write	The user name used to log into the mail server if authentication is required.
STR emailWarningFromEmail	1.3.6.1.4.1.8691.2.13.1.5.2.3.5	DisplayString	read-write	The e-mail address to be filled in the 'From' field of the auto-warning e-mail.
STR emailWarningFirstEmailAddr	1.3.6.1.4.1.8691.2.13.1.5.2.3.6	DisplayString	read-write	The first email address to where the auto-warning e-mail is to be sent.
STR emailWarningSecondEmailAddr	1.3.6.1.4.1.8691.2.13.1.5.2.3.7	DisplayString	read-write	The second email address to where the auto-warning e-mail is to be sent.
STR emailWarningThirdEmailAddr	1.3.6.1.4.1.8691.2.13.1.5.2.3.8	DisplayString	read-write	The third email address to where the auto-warning e-mail is to be sent.
STR emailWarningFourthEmailAddr	1.3.6.1.4.1.8691.2.13.1.5.2.3.9	DisplayString	read-write	The fourth email address to where the auto-warning e-mail is to be sent.
snmpTrap	1.3.6.1.4.1.8691.2.13.1.5.2.4
STR snmpTrapReceiverIp	1.3.6.1.4.1.8691.2.13.1.5.2.4.1	DisplayString	read-write	SNMP trap server IP address or domain name.
INT trapVersion	1.3.6.1.4.1.8691.2.13.1.5.2.4.2	INTEGER	read-write	SNMP trap version used for the auto-warning function.
maintenance	1.3.6.1.4.1.8691.2.13.1.5.3
consoleSettings	1.3.6.1.4.1.8691.2.13.1.5.3.1
INT httpConsole	1.3.6.1.4.1.8691.2.13.1.5.3.1.1	INTEGER	read-write	Enable or disable HTTP console.
INT httpsConsole	1.3.6.1.4.1.8691.2.13.1.5.3.1.2	INTEGER	read-write	Enable or disable HTTPS console.
INT telnetConsole	1.3.6.1.4.1.8691.2.13.1.5.3.1.3	INTEGER	read-write	Enable or disable Telnet console.
INT sshConsole	1.3.6.1.4.1.8691.2.13.1.5.3.1.4	INTEGER	read-write	Enable or disable SSH console.
INT serialConsole	1.3.6.1.4.1.8691.2.13.1.5.3.1.5	INTEGER	read-write	Enable or disable Serial console.
INT resetButton	1.3.6.1.4.1.8691.2.13.1.5.3.1.6	INTEGER	read-write	Reset button setting.
loadFactoryDefault	1.3.6.1.4.1.8691.2.13.1.5.3.2
INT loadFactoryDefaultSetting	1.3.6.1.4.1.8691.2.13.1.5.3.2.1	INTEGER	write-only	This function will reset all of the NPort W2x50A series device server's settings to the factory default values. Be aware that previous settings will be lost. Selecting Reset to factory default (excluding IP configuration) will reset all settings except the IP configuration to factory defaults. Selecting Reset to factory default will reset all settings including the IP configuration to factory defaults.
sysStatus	1.3.6.1.4.1.8691.2.13.1.6
s2eConnections	1.3.6.1.4.1.8691.2.13.1.6.1
monitorRemoteIpTable	1.3.6.1.4.1.8691.2.13.1.6.1.1		not-accessible	Serial to Network Connections Remote IP table.
monitorRemoteIpEntry	1.3.6.1.4.1.8691.2.13.1.6.1.1.1		not-accessible	Serial to Network Connections Remote IP entry.
INT remoteIpIndex	1.3.6.1.4.1.8691.2.13.1.6.1.1.1.1	INTEGER	read-only	Serial to Network Connections Remote IP index.
IP monitorRemoteIp	1.3.6.1.4.1.8691.2.13.1.6.1.1.1.2	IpAddress	read-only	The remote IP currently connecting to this port.
serialPortStatus	1.3.6.1.4.1.8691.2.13.1.6.2
monitorSerialPortStatusTable	1.3.6.1.4.1.8691.2.13.1.6.2.1		not-accessible	Serial Port Status table.
monitorSerialPortStatusEntry	1.3.6.1.4.1.8691.2.13.1.6.2.1.1		not-accessible	Serial Port Status entry.
INT monitorTxCount	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.1	INTEGER	read-only	View the number of bytes transmitted from the port since the last time the port was initialized.
INT monitorRxCount	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.2	INTEGER	read-only	View the number of bytes received by the port since the last time the port was initialized.
INT monitorTxTotalCount	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.3	INTEGER	read-only	View the number of bytes transmitted from the port since the last time the system was initialized.
INT monitorRxTotalCount	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.4	INTEGER	read-only	View the number of bytes received by the port since the last time the system was initialized.
INT monitorDSR	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.5	INTEGER	read-only	View the current DSR status of this port.
INT monitorDTR	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.6	INTEGER	read-only	View the current DTR status of this port.
INT monitorRTS	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.7	INTEGER	read-only	View the current RTS status of this port.
INT monitorCTS	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.8	INTEGER	read-only	View the current CTS status of this port.
INT monitorDCD	1.3.6.1.4.1.8691.2.13.1.6.2.1.1.9	INTEGER	read-only	View the current DCD status of this port.
serialPortErrorCount	1.3.6.1.4.1.8691.2.13.1.6.3
monitorSerialPortErrorCountTable	1.3.6.1.4.1.8691.2.13.1.6.3.1		not-accessible	Serial Port Error Count table.
monitorSerialPortErrorCountEntry	1.3.6.1.4.1.8691.2.13.1.6.3.1.1		not-accessible	Serial Port Error Count entry.
INT monitorErrorCountFrame	1.3.6.1.4.1.8691.2.13.1.6.3.1.1.1	INTEGER	read-only	View the number of 'Frame' errors for this port.
INT monitorErrorCountParity	1.3.6.1.4.1.8691.2.13.1.6.3.1.1.2	INTEGER	read-only	View the number of 'Parity' errors for this port.
INT monitorErrorCountOverrun	1.3.6.1.4.1.8691.2.13.1.6.3.1.1.3	INTEGER	read-only	View the number of 'Overrun' errors for this port.
INT monitorErrorCountBreak	1.3.6.1.4.1.8691.2.13.1.6.3.1.1.4	INTEGER	read-only	View the number of 'Break' errors for this port.
serialPortSettings	1.3.6.1.4.1.8691.2.13.1.6.4
monitorSerialPortSettingsTable	1.3.6.1.4.1.8691.2.13.1.6.4.1		not-accessible	Serial Port Settings table.
monitorSerialPortSettingsEntry	1.3.6.1.4.1.8691.2.13.1.6.4.1.1		not-accessible	Serial Port Settings entry.
INT monitorBaudRate	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.1	INTEGER	read-only	View the current baudrate of the port.
INT monitorDataBits	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.2	INTEGER	read-only	View the number of bits per byte for the port.
STR monitorStopBits	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.3	DisplayString	read-only	View the number of stop bits for the port.
INT monitorParity	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.4	INTEGER	read-only	View the parity bit for the port.
INT monitorRTSCTSFlowControl	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.5	INTEGER	read-only	View if the port is using RTS/CTS flow control.
INT monitorXONXOFFFlowControl	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.6	INTEGER	read-only	View if the port is using XON/XOFF flow control.
INT monitorFIFO	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.7	INTEGER	read-only	View FIFO status of this port.
INT monitorInterface	1.3.6.1.4.1.8691.2.13.1.6.4.1.1.8	INTEGER	read-only	View the serial interface that the port is using.
serialPortBuffering	1.3.6.1.4.1.8691.2.13.1.6.5
monitorSerialPortBufferingTable	1.3.6.1.4.1.8691.2.13.1.6.5.1		not-accessible	Serial Port Buffering table.
monitorSerialPortBufferingEntry	1.3.6.1.4.1.8691.2.13.1.6.5.1.1		not-accessible	Serial Port Settings entry.
INT monitorBuffering	1.3.6.1.4.1.8691.2.13.1.6.5.1.1.1	INTEGER	read-only	View length of buffered data for the port. The length unit is byte.
sysWlanStatus	1.3.6.1.4.1.8691.2.13.1.6.6
STR wlanStatusActiveProfileName	1.3.6.1.4.1.8691.2.13.1.6.6.1	DisplayString	read-only	The active profile name.
INT wlanStatusIpConfiguration	1.3.6.1.4.1.8691.2.13.1.6.6.2	INTEGER	read-only	The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP.
IP wlanStatusIpAddress	1.3.6.1.4.1.8691.2.13.1.6.6.3	IpAddress	read-only	An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
IP wlanStatusNetMask	1.3.6.1.4.1.8691.2.13.1.6.6.4	IpAddress	read-only	A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort W2x50A series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort W2x50A series device server, a connection is established directly from the NPort W2x50A series device server. Otherwise, the connection is established through the given default gateway.
IP wlanStatusDefaultGateway	1.3.6.1.4.1.8691.2.13.1.6.6.5	IpAddress	read-only	A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort W2x50A series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
STR wlanStatusNetworkType	1.3.6.1.4.1.8691.2.13.1.6.6.6	DisplayString	read-only	Network Type of Wireless LAN. The possible values are 'Infrastrcture Mode' and 'Ad-hoc Mode'
STR wlanStatusRFType	1.3.6.1.4.1.8691.2.13.1.6.6.7	DisplayString	read-only	RF type of Wireless LAN. The possible values are 'N/A', 'Auto', '802.11a', '802.11b', '802.11g'
STR wlanStatusSSID	1.3.6.1.4.1.8691.2.13.1.6.6.8	DisplayString	read-only	The SSID of WLAN.
STR wlanStatusChannel	1.3.6.1.4.1.8691.2.13.1.6.6.9	DisplayString	read-only	The currently used channel.
STR wlanStatusAuthentication	1.3.6.1.4.1.8691.2.13.1.6.6.10	DisplayString	read-only	Authentication type of Wireless LAN. The possible values are 'Unknown', 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK'
STR wlanStatusEncryption	1.3.6.1.4.1.8691.2.13.1.6.6.11	DisplayString	read-only	Show encryption type of Wireless LAN.
STR wlanStatusRegion	1.3.6.1.4.1.8691.2.13.1.6.6.12	DisplayString	read-only	Display region. The possible values are 'US', 'EU', 'JP'
STR wlanStatusSignalStrength	1.3.6.1.4.1.8691.2.13.1.6.6.13	DisplayString	read-only	The signal strength of Wireless LAN.
STR wlanStatusConnectionSpeed	1.3.6.1.4.1.8691.2.13.1.6.6.14	DisplayString	read-only	The connection speed of Wireless LAN.
STR wlanStatusCurrentBSSID	1.3.6.1.4.1.8691.2.13.1.6.6.15	DisplayString	read-only	The current BSSID of Wireless LAN.
activateSettings	1.3.6.1.4.1.8691.2.13.1.7
INT doActivate	1.3.6.1.4.1.8691.2.13.1.7.1	INTEGER	write-only	Activate current settings.
restart	1.3.6.1.4.1.8691.2.13.1.8
INT restartPorts	1.3.6.1.4.1.8691.2.13.1.8.1	INTEGER	write-only	Restart serial port. Restarting will cause port reseting.
INT restartSystem	1.3.6.1.4.1.8691.2.13.1.8.2	INTEGER	write-only	Restart the NPort W2x50A series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes will be lost.

RFC description

NPort W2x50A industrial serial device server management and configuration.

Start monitoring Moxa NPort W2150A/W2250A wireless serial device server with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download MOXA-W2x50A-MIB

What Is MOXA-W2x50A-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description