CISCO-IPSLA-VIDEO-MIB

All MIBs › CISCO-IPSLA-VIDEO-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2010-06-11

Category: Cisco Devices, Quality of Service, Telephony and VoIP

Description: Manages IP SLA video quality probes measuring MOS, packet loss, and jitter for video traffic.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-IPSLA-VIDEO-MIB?

CISCO-IPSLA-VIDEO-MIB is a Cisco enterprise MIB that is part of the IP SLA (Service Level Agreement) active-monitoring feature family, specifically covering the 'video' IP SLA operation used to assess video traffic quality across a network. It exposes performance statistics such as positive/negative frame-timing deviations (jitter-like spread metrics), packet counts, and aggregated versus latest-sample statistics tables. This MIB is squarely a software/performance monitoring tool: it lets an operator track real-time and historical video-quality metrics (akin to jitter, delay variation, and sample counts) rather than physical hardware health, helping detect degraded video experience before end users complain. It depends on the broader Cisco RTTMON/IP SLA framework, notably rttMonEchoAdminProtocol from CISCO-RTTMON-MIB, to actually configure and run the video probe. It is typically deployed on Cisco routers and switches acting as IP SLA responders/sources in networks carrying VoIP/video traffic, such as enterprise WAN or service-provider video-delivery infrastructure. Engineers can download the CISCO-IPSLA-VIDEO-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-IPSLA-VIDEO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco router
Cisco switch (IP SLA-capable)

Monitoring Examples

An administrator would poll cipslaLatestVideoStatsTable/cipslaLatestVideoStatsEntry for the most recent probe result, examining cipslaLatestVideoMinPosSD, cipslaLatestVideoMaxPosSD, and cipslaLatestVideoSumPosSD (and their negative-SD counterparts) to gauge the spread of frame-timing deviations. Comparing these latest-sample values against the aggregated cipslaVideoAggStatsTable over time can reveal a trend of worsening jitter that correlates with network congestion. A sudden spike in cipslaLatestVideoNumNegSD relative to baseline would flag video quality degradation on a monitored path.

What Can Be Monitored

video probe jitter/frame-deviation statistics
positive/negative SD sample counts and sums
latest vs. aggregated video quality stats
IP SLA video operation status

Imported Objects

From CISCO-RTTMON-MIB

rttMonCtrlAdminIndex

OBJECT-TYPE

From CISCO-RTTMON-TC-MIB

RttResponseSense

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TimeStamp

How to Use in IPNetwork Monitor

Example using cipslaLatestVideoUnSyncRTs OID:

Select a Cisco router/switch (IP SLA video) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cipslaLatestVideoUnSyncRTs into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of RTT operations that have completed with sender and responder out of sync with NTP. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
G32 cipslaLatestVideoAvgJitterSD	1.3.6.1.4.1.9.9.744.1.1.1.1.19	Gauge32	read-only	The average of positive and negative jitter values in Source-to-Destination direction.
STR cipslaLatestVideoErrSenseDescr	1.3.6.1.4.1.9.9.744.1.1.1.1.21	SnmpAdminString	read-only	An sense description for the completion status of the latest video operation.
G32 cipslaLatestVideoIAJOut	1.3.6.1.4.1.9.9.744.1.1.1.1.20	Gauge32	read-only	Inter-arrival jitter (RFC 1889) at responder.
G32 cipslaLatestVideoIPDVAvgSDJ	1.3.6.1.4.1.9.9.744.1.1.1.1.26	Gauge32	read-only	Source to Destination IPDV average jitter according to RFC 5481.
G32 cipslaLatestVideoMaxNegSD	1.3.6.1.4.1.9.9.744.1.1.1.1.7	Gauge32	read-only	The maximum of absolute values of all negative jitter values for packets sent from source to destination.
G32 cipslaLatestVideoMaxPosSD	1.3.6.1.4.1.9.9.744.1.1.1.1.2	Gauge32	read-only	The maximum of all positive jitter values for packets sent from source to destination.
G32 cipslaLatestVideoMinNegSD	1.3.6.1.4.1.9.9.744.1.1.1.1.6	Gauge32	read-only	The minimum of absolute values of all negative jitter values for packets sent from source to destination.
G32 cipslaLatestVideoMinPosSD	1.3.6.1.4.1.9.9.744.1.1.1.1.1	Gauge32	read-only	The minimum of all positive jitter values for packets sent from source to destination.
INT cipslaLatestVideoNTPState	1.3.6.1.4.1.9.9.744.1.1.1.1.25	INTEGER	read-only	A value of sync(1) means sender and responder was in sync with NTP. The NTP sync means the total of NTP offset on sender and responder is within configured tolerance level.
G32 cipslaLatestVideoNumNegSD	1.3.6.1.4.1.9.9.744.1.1.1.1.8	Gauge32	read-only	The number of all negative jitter values for packets sent from source to destination.
G32 cipslaLatestVideoNumOWSD	1.3.6.1.4.1.9.9.744.1.1.1.1.18	Gauge32	read-only	The number of successful one way trip time measurements from source to destination.
G32 cipslaLatestVideoNumPosSD	1.3.6.1.4.1.9.9.744.1.1.1.1.3	Gauge32	read-only	The number of all positive jitter values for packets sent from source to destination.
G32 cipslaLatestVideoOWAvgSD	1.3.6.1.4.1.9.9.744.1.1.1.1.27	Gauge32	read-only	The average latency value from source to destination.
G32 cipslaLatestVideoOWMaxSD	1.3.6.1.4.1.9.9.744.1.1.1.1.17	Gauge32	read-only	The maximum of all one way trip time from source to destination.
G32 cipslaLatestVideoOWMinSD	1.3.6.1.4.1.9.9.744.1.1.1.1.16	Gauge32	read-only	The minimum of all one way trip time from source to destination.
G32 cipslaLatestVideoOWSum2SD	1.3.6.1.4.1.9.9.744.1.1.1.1.15	Gauge32	read-only	The sum of squares of one way trip time from source to destination.
G32 cipslaLatestVideoOWSum2SDHigh	1.3.6.1.4.1.9.9.744.1.1.1.1.24	Gauge32	read-only	The sum of squares of one way latency from source to destination (high order 32 bits). The low order 32 bits are stored in cipslaLatestVideoOWSum2SD.
G32 cipslaLatestVideoOWSumSD	1.3.6.1.4.1.9.9.744.1.1.1.1.14	Gauge32	read-only	The sum of one way trip time from source to destination.
G32 cipslaLatestVideoOWSumSDHigh	1.3.6.1.4.1.9.9.744.1.1.1.1.23	Gauge32	read-only	The sum of one way latency from source to destination (high order 32 bits). The low order 32 bits are stored in cipslaLatestVideoOWSumSD.
G32 cipslaLatestVideoPktLateArrival	1.3.6.1.4.1.9.9.744.1.1.1.1.28	Gauge32	read-only	The number of packets that arrived after the timeout.
G32 cipslaLatestVideoPktLossSD	1.3.6.1.4.1.9.9.744.1.1.1.1.11	Gauge32	read-only	The number of packets lost when sent from source to destination.
G32 cipslaLatestVideoPktOutSeq	1.3.6.1.4.1.9.9.744.1.1.1.1.12	Gauge32	read-only	The number of packets arrived out of sequence.
RTT cipslaLatestVideoSense	1.3.6.1.4.1.9.9.744.1.1.1.1.13	RttResponseSense	read-only	An application specific sense code for the completion status.
cipslaLatestVideoStatsEntry	1.3.6.1.4.1.9.9.744.1.1.1.1		not-accessible	A collection of objects that record the latest Video jitter operation. An entry is created only when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state.
cipslaLatestVideoStatsTable	1.3.6.1.4.1.9.9.744.1.1.1		not-accessible	The 'video' operation sends out video streams at the frequency specified by rttMonCtrlAdminFrequency. This table contains the statistics calculated for the latest video packets. Each conceptual row in this table corresponds to an 'video' operation defined in rttMonCtrlAdminTable and has same index as rttMonCtrlAdminTable.
G32 cipslaLatestVideoSum2NegSD	1.3.6.1.4.1.9.9.744.1.1.1.1.10	Gauge32	read-only	The sum of square of all negative jitter values for packets sent from source to destination.
G32 cipslaLatestVideoSum2PosSD	1.3.6.1.4.1.9.9.744.1.1.1.1.5	Gauge32	read-only	The sum of square of all positive jitter values for packets sent from source to destination.
G32 cipslaLatestVideoSumNegSD	1.3.6.1.4.1.9.9.744.1.1.1.1.9	Gauge32	read-only	The sum of all negative jitter values for packets sent from source to destination. The number of such values is stored in cipslaLatestVideoNumNegSD.
G32 cipslaLatestVideoSumPosSD	1.3.6.1.4.1.9.9.744.1.1.1.1.4	Gauge32	read-only	The sum of all positive jitter values for packets sent source to destination. The number of such values is stored in cipslaLatestVideoNumPosSD.
C32 cipslaLatestVideoUnSyncRTsEx	1.3.6.1.4.1.9.9.744.1.1.1.1.22	Counter32	read-only	The number of RTT operations that have completed with sender and responder out of sync with NTP. The NTP sync means the total of NTP offset on sender and responder is within configured tolerance level
G32 cipslaVideoAggAvgJSD	1.3.6.1.4.1.9.9.744.1.2.1.1.27	Gauge32	read-only	The average of positive and negative jitter values in source-to-destination direction.
C32 cipslaVideoAggBusies	1.3.6.1.4.1.9.9.744.1.2.1.1.20	Counter32	read-only	The number of occasions when a video operation could not be initiated because a previous video operation has not been completed.
C32 cipslaVideoAggCompletions	1.3.6.1.4.1.9.9.744.1.2.1.1.2	Counter32	read-only	The number of video operations that have completed successfully.
C32 cipslaVideoAggErrors	1.3.6.1.4.1.9.9.744.1.2.1.1.19	Counter32	read-only	The number of occasions when a video operation could not be initiated because of an internal error.
G32 cipslaVideoAggIAJIn	1.3.6.1.4.1.9.9.744.1.2.1.1.29	Gauge32	read-only	Inter-arrival jitter (RFC 1889) at sender
G32 cipslaVideoAggIAJOut	1.3.6.1.4.1.9.9.744.1.2.1.1.28	Gauge32	read-only	Inter-arrival jitter (RFC 1889) at responder
G32 cipslaVideoAggMaxNegSD	1.3.6.1.4.1.9.9.744.1.2.1.1.11	Gauge32	read-only	The maximum of all negative jitter values for packets sent from source to destination.
G32 cipslaVideoAggMaxPosSD	1.3.6.1.4.1.9.9.744.1.2.1.1.5	Gauge32	read-only	The maximum of absolute values of all positive jitter values for packets sent from source to destination.
G32 cipslaVideoAggMinNegSD	1.3.6.1.4.1.9.9.744.1.2.1.1.10	Gauge32	read-only	The minimum of all negative jitter values for packets sent from source to destination.
G32 cipslaVideoAggMinPosSD	1.3.6.1.4.1.9.9.744.1.2.1.1.4	Gauge32	read-only	The minimum of absolute values of all positive jitter values for packets sent from source to destination.
C32 cipslaVideoAggNumNegSD	1.3.6.1.4.1.9.9.744.1.2.1.1.12	Counter32	read-only	The number of all negative jitter values for packets sent from source to destination.
C32 cipslaVideoAggNumOWSD	1.3.6.1.4.1.9.9.744.1.2.1.1.26	Counter32	read-only	The number of one way trip time that are successfully measured from source to destination.
C32 cipslaVideoAggNumPosSD	1.3.6.1.4.1.9.9.744.1.2.1.1.6	Counter32	read-only	The number of all positive jitter values for packets sent from source to destination.
C32 cipslaVideoAggOverThresholds	1.3.6.1.4.1.9.9.744.1.2.1.1.3	Counter32	read-only	The number of video operations that violate jitterAvg threshold which is defined in RttMonReactVar.
G32 cipslaVideoAggOWMaxSD	1.3.6.1.4.1.9.9.744.1.2.1.1.25	Gauge32	read-only	The maximum of all one way trip time from source to destination.
G32 cipslaVideoAggOWMinSD	1.3.6.1.4.1.9.9.744.1.2.1.1.24	Gauge32	read-only	The minimum of all one way trip time from source to destination.
C32 cipslaVideoAggOWSum2SDHigh	1.3.6.1.4.1.9.9.744.1.2.1.1.23	Counter32	read-only	The sum of squares of one way trip time from source to destination (high order 32 bits).
C32 cipslaVideoAggOWSum2SDLow	1.3.6.1.4.1.9.9.744.1.2.1.1.22	Counter32	read-only	The sum of squares of one way trip time from source to destination (low order 32 bits).
C32 cipslaVideoAggOWSumSD	1.3.6.1.4.1.9.9.744.1.2.1.1.21	Counter32	read-only	The sum of one way trip time from source to destination.
C32 cipslaVideoAggOWSumSDHigh	1.3.6.1.4.1.9.9.744.1.2.1.1.32	Counter32	read-only	The sum of one way times from source to destination (high order 32 bits). The low order 32 bits are stored in cipslaVideoAggOWSumSD.
C32 cipslaVideoAggPktLateArrival	1.3.6.1.4.1.9.9.744.1.2.1.1.30	Counter32	read-only	The number of packets that arrived after the timeout.
C32 cipslaVideoAggPktLossSD	1.3.6.1.4.1.9.9.744.1.2.1.1.16	Counter32	read-only	The number of lost packets when sent from source to destination.
C32 cipslaVideoAggPktOutSeq	1.3.6.1.4.1.9.9.744.1.2.1.1.17	Counter32	read-only	The number of packets arrived out of sequence.
C32 cipslaVideoAggPktSkipped	1.3.6.1.4.1.9.9.744.1.2.1.1.18	Counter32	read-only	The number of packets that are skipped per operation because the router could not send the packet out.
TIM cipslaVideoAggStartTimeId	1.3.6.1.4.1.9.9.744.1.2.1.1.1	TimeStamp	not-accessible	The value of sysUpTime at the time when this row was created.
cipslaVideoAggStatsEntry	1.3.6.1.4.1.9.9.744.1.2.1.1		not-accessible	This entry contains the objects which accumulate the results of a series of 'video' operations over a 60 minute time period or a time period stored in rttMonScheduleAdminRttLife, whichever is smaller. An entry is created only if when the following objects are valid. - rttMonCtrlAdminRttType - rttMonEchoAdminProtocol The entry will start to collect data when rttMonCtrlAdminStatus is in 'active' state. The entry will be removed when the rttMonCtrlAdminStatus is changed to 'destroy' state. cipslaVideoAggStartTimeId will be created at the beginning of the hour and will keep aggregating statistics until the end of the hour.
cipslaVideoAggStatsTable	1.3.6.1.4.1.9.9.744.1.2.1		not-accessible	The 'video' statistics table contains summarized information of the results for a conceptual control row. A rolling accumulated history of this information is maintained in a series of hourly 'group(s)'. When ipslaVideoAggStartTimeId groups exceeds the rttMonStatisticsAdminNumHourGroups value, the oldest corresponding hourly group will be deleted and will be replaced with the new ipslaVideoAggStatsStartTimeId hourly group.
C32 cipslaVideoAggSum2NegSDHigh	1.3.6.1.4.1.9.9.744.1.2.1.1.15	Counter32	read-only	The sum of square of all negative jitter values for packets sent from source to destination (high order 32 bits).
C32 cipslaVideoAggSum2NegSDLow	1.3.6.1.4.1.9.9.744.1.2.1.1.14	Counter32	read-only	The sum of square of all negative jitter values for packets sent from source to destination (low order 32 bits).
C32 cipslaVideoAggSum2PosSDHigh	1.3.6.1.4.1.9.9.744.1.2.1.1.9	Counter32	read-only	The sum of square of all positive jitter values for packets sent from source to destination (high order 32 bits).
C32 cipslaVideoAggSum2PosSDLow	1.3.6.1.4.1.9.9.744.1.2.1.1.8	Counter32	read-only	The sum of square of all positive jitter values for packets sent from source to destination (low order 32 bits).
C32 cipslaVideoAggSumNegSD	1.3.6.1.4.1.9.9.744.1.2.1.1.13	Counter32	read-only	The sum of all negative jitter values for packets sent from source to destination. The number of such values is stored in ipslaVideoAggNumNegSDs.
C32 cipslaVideoAggSumPosSD	1.3.6.1.4.1.9.9.744.1.2.1.1.7	Counter32	read-only	The sum of all positive jitter values for packets sent from source to destination. The number of such values is stored in ipslaVideoAggNumPosSDs.
C32 cipslaVideoAggUnSyncRTs	1.3.6.1.4.1.9.9.744.1.2.1.1.31	Counter32	read-only	The number of RTT operations that have completed with sender and responder out of sync with NTP. The NTP sync means the total of NTP offset on sender and responder is within configured tolerance level
cipslaVideoLatestOper	1.3.6.1.4.1.9.9.744.1.1
cipslaVideoStats	1.3.6.1.4.1.9.9.744.1.2
ciscoIpslaVideoMIB	1.3.6.1.4.1.9.9.744			IP SLA is a capability which utilizes active monitoring for network performance. It can be used for network troubleshooting, network assessment and health monitoring. This MIB defines a collection of statistics resulting from the 'video' IP SLA operation. The Video Statistics table names are: cipslaLatestVideoStatsTable --- Contains only the latest statistics cipslaVideoAggStatsTable --- Contains aggregated statistics To create the Video operation, set rttMonEchoAdminProtocol (defined in CISCO-RTTMON-MIB) object to 'videoAppl'. Once the operation has been scheduled, both cipslaLatestVideoStatsTable and cipslaVideoAggStatsTable will be populated. Glossary: IP SLA - Cisco IOS IP Service Level Agreements IP SLA operation - Refers to the 'video' operation supported by IP SLA. RTT - Round Trip Time
ciscoIpslaVideoMIBCompliance	1.3.6.1.4.1.9.9.744.2.1.1			This is a default module-compliance containing default object groups.
ciscoIpslaVideoMIBCompliances	1.3.6.1.4.1.9.9.744.2.1
ciscoIpslaVideoMIBConform	1.3.6.1.4.1.9.9.744.2
ciscoIpslaVideoMIBGroups	1.3.6.1.4.1.9.9.744.2.2
ciscoIpslaVideoMIBNotifs	1.3.6.1.4.1.9.9.744.0
ciscoIpslaVideoMIBObjects	1.3.6.1.4.1.9.9.744.1
ciscoIpslaVideoStatsGroup	1.3.6.1.4.1.9.9.744.2.2.1			A collection of statistics objects related to Video Probe.

RFC description

Cisco vendor-private MIB for IP SLA (Service Level Agreement) video quality monitoring and metrics.

Start monitoring Cisco router/switch (IP SLA video) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-IPSLA-VIDEO-MIB