CISCO-DOT11-CONTEXT-SERVICES-CLIENT-MIB

MIB Reference — IPNetwork Monitor · Updated October 05, 2026

All MIBs › CISCO-DOT11-CONTEXT-SERVICES-CLIENT-MIB

Organization: Cisco Systems Inc.

Last Updated: 2004-06-02

Category: Cisco Devices, Wireless and WLAN

Description: Manages 802.11 IAPP context services on Cisco wireless clients, tracking inter-AP roaming context transfers and client state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-DOT11-CONTEXT-SERVICES-CLIENT-MIB?

This MIB manages 802.11 IAPP (Inter-Access Point Protocol) context services on the client/mobile-node side within Cisco's Wireless Domain Services (WDS) and Wireless Network Services (WNS) architecture, tracking how a wireless client's session context is transferred as it roams between access points. It exposes objects describing the mobile node's parent WDS address, root node address, authenticator address, operating mode, and state-transition counters. Its monitoring value is largely about wireless client roaming health and software-state visibility: cDot11CscStateTransitions and cDot11CscOperMode let an administrator see how frequently and successfully clients hand off context between access points, while cDot11CscMnInactivityTime and cDot11CscRegistrationLifeTime reveal session/registration timeout behavior. It is closely tied to the companion CISCO-DOT11-CONTEXT-SERVICES-MIB (the WDS/WNS infrastructure side) and to the underlying IEEE 802.11 standard. It is deployed on Cisco wireless access points and bridges participating in enterprise Wi-Fi roaming domains, where the CISCO-DOT11-CONTEXT-SERVICES-CLIENT-MIB MIB tracks client handoff state.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-DOT11-CONTEXT-SERVICES-CLIENT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • Cisco 802.11 access points and wireless bridges
  • wireless client roaming context (mobile node side)

Monitoring Examples

A wireless engineer would monitor cDot11CscStateTransitions alongside cDot11CscParentWdsAddress and cDot11CscRootNodeAddress to confirm a roaming client is correctly re-registering with a new access point as it moves. An unexpectedly high cDot11CscStateTransitions count paired with a short cDot11CscMnInactivityTime could indicate a client repeatedly flapping between access points instead of holding a stable association. Checking cDot11CscMnAuthenticatorAddress after a roam confirms the client's authentication context followed it to the new parent node.

What Can Be Monitored

  • client roaming state transitions
  • parent WDS/root node address
  • authenticator address
  • operating mode
  • inactivity timer
  • registration lifetime
Imported Objects

From CISCO-SMI

ciscoExperimentOBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TimeInterval

How to Use in IPNetwork Monitor

Example using cDot11CscStateTransitions OID:

Select a Cisco 802.11 access points and wireless bridge (WLCCP client) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cDot11CscStateTransitions into the Find box to locate it in the OID tree, then select it and click OK. This object counts the number of times this 802.11 station has transitioned between the infrastructure and distributed modes since the last reboot. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs

RFC description

MIB for 802.11 access points and wireless bridges participating in context management and WDS/WNS services.

Start monitoring Cisco 802.11 access points and wireless bridges (WLCCP client) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-DOT11-CONTEXT-SERVICES-CLIENT-MIB