BayNetworks-AHB-MIB

All MIBs › BayNetworks-AHB-MIB

Category: Vendor: Avaya

Description: Manages Bay Networks Access Hub (AHB) concentrator hardware, covering port status and chassis configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BayNetworks-AHB-MIB?

BayNetworks-AHB-MIB is a Bay Networks vendor MIB for managing the Access Hub (AHB) concentrator, an Ethernet/Token Ring hub/concentrator product from Bay Networks' legacy hardware line. It is intended to expose chassis and per-port configuration and status data for the concentrator, though no concrete sample objects were available to ground specific leaves. Its monitoring purpose, consistent with other hub/concentrator MIBs of its era, would be hardware status, reporting port up/down/link state and overall chassis/module health so operators can detect a failed port or hub module. It likely depends on Bay Networks' broader proprietary chassis/hub MIB conventions and possibly standard interface MIBs for basic counters. It would have been deployed in enterprise LAN wiring closets during the era when Bay Networks Access Hub concentrators provided shared Ethernet/Token Ring connectivity. Engineers can download the BayNetworks-AHB-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BayNetworks-AHB-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Bay Networks Access Hub (AHB) concentrator

Monitoring Examples

No concrete object or table names were supplied for this module, so a specific monitoring scenario cannot be grounded in real data. Typically, a hub/concentrator MIB of this kind would let an operator poll per-port status to detect a failed or disconnected port and overall chassis health to detect a failed power supply or module, but without sample objects this cannot be stated as fact for this specific MIB.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfAtmHalfBridgeGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfAhb	1.3.6.1.4.1.18.3.5.9.13.1
STR wfAhbAltInitFile	1.3.6.1.4.1.18.3.5.9.13.1.5	DisplayString	read-write	Name of alternate file containing AHB initial host entries.
INT wfAhbAutoLearnMethod	1.3.6.1.4.1.18.3.5.9.13.1.3	INTEGER	read-write	Method used to dynamically learn new host entries.
INT wfAhbBaseStatus	1.3.6.1.4.1.18.3.5.9.13.1.18	INTEGER	read-only	Status of the AHB module.
IP wfAhbCctDefSubNetMask	1.3.6.1.4.1.18.3.5.9.13.2.1.4	IpAddress	read-write	The default subnet mask for hosts learned unsecurely on this interface.
INT wfAhbCctDelete	1.3.6.1.4.1.18.3.5.9.13.2.1.1	INTEGER	read-write	Create/Delete this ATM HALF BRIDGE interface.
INT wfAhbCctDisable	1.3.6.1.4.1.18.3.5.9.13.2.1.2	INTEGER	read-write	Enable/disable this ATM HALF BRIDGE interface.
wfAhbCctEntry	1.3.6.1.4.1.18.3.5.9.13.2.1		not-accessible	ATM Half Bridge Interface Entry.
INT wfAhbCctMaxIdleTime	1.3.6.1.4.1.18.3.5.9.13.2.1.6	INTEGER	read-write	Maximum idle time for aging unsecure host entries
INT wfAhbCctNum	1.3.6.1.4.1.18.3.5.9.13.2.1.3	INTEGER	read-only	The circuit number associated with this AHB interface.
INT wfAhbCctProxyArpDisable	1.3.6.1.4.1.18.3.5.9.13.2.1.5	INTEGER	read-write	Enable/Disable proxy ARP function on this interface.
CTR wfAhbCctRxDrop	1.3.6.1.4.1.18.3.5.9.13.2.1.11	Counter	read-only	Number of incoming packets dropped on this interface.
CTR wfAhbCctRxPkts	1.3.6.1.4.1.18.3.5.9.13.2.1.10	Counter	read-only	Number of incoming packets received on this interface.
INT wfAhbCctStatus	1.3.6.1.4.1.18.3.5.9.13.2.1.7	INTEGER	read-only	Status of the corresponding ATM circuit.
wfAhbCctTable	1.3.6.1.4.1.18.3.5.9.13.2		not-accessible	A list of circuit entries in ATM bridge table.
CTR wfAhbCctTxDrop	1.3.6.1.4.1.18.3.5.9.13.2.1.9	Counter	read-only	Number of outgoing packets dropped on this interface.
CTR wfAhbCctTxPkts	1.3.6.1.4.1.18.3.5.9.13.2.1.8	Counter	read-only	Number of outgoing packets sent on this interface.
INT wfAhbDebugLevel	1.3.6.1.4.1.18.3.5.9.13.1.6	INTEGER	read-write	Level of debug messages to include in system log. Zero indicates no debug messages, higher values display more detailed information.
INT wfAhbDelete	1.3.6.1.4.1.18.3.5.9.13.1.1	INTEGER	read-write	Create or Delete AHB Function.
INT wfAhbDisable	1.3.6.1.4.1.18.3.5.9.13.1.2	INTEGER	read-write	Enables or Disables AHB Function.
STR wfAhbHostBridgeHdr	1.3.6.1.4.1.18.3.5.9.13.3.1.8	DisplayString	read-write	The bridge DLL header associated with this host entry.
INT wfAhbHostCct	1.3.6.1.4.1.18.3.5.9.13.3.1.6	INTEGER	read-write	The circuit number associated with this host entry.
INT wfAhbHostCurIdleTime	1.3.6.1.4.1.18.3.5.9.13.3.1.13	INTEGER	read-only	Remaining idle time for this host entry.
INT wfAhbHostDelete	1.3.6.1.4.1.18.3.5.9.13.3.1.1	INTEGER	read-write	Create/Delete this half-bridge host entry.
wfAhbHostEntry	1.3.6.1.4.1.18.3.5.9.13.3.1		not-accessible	ATM Half Bridge Host Entry.
INT wfAhbHostFlags	1.3.6.1.4.1.18.3.5.9.13.3.1.9	INTEGER	read-write	Various control flag bits for this host entry. See router documentation for bit definitions.
IP wfAhbHostIpAddress	1.3.6.1.4.1.18.3.5.9.13.3.1.4	IpAddress	read-only	The IP address associated with this host entry.
INT wfAhbHostMaxIdleTime	1.3.6.1.4.1.18.3.5.9.13.3.1.12	INTEGER	read-write	Maximum idle time for this host entry.
CTR wfAhbHostRxPkts	1.3.6.1.4.1.18.3.5.9.13.3.1.11	Counter	read-only	Number of incoming packets received on this host entry.
INT wfAhbHostSeqNum	1.3.6.1.4.1.18.3.5.9.13.3.1.3	INTEGER	read-write	Sequence number assigned to this entry (must be zero on create).
INT wfAhbHostSlot	1.3.6.1.4.1.18.3.5.9.13.3.1.2	INTEGER	read-only	The slot number which is reporting this host entry. If this is a new host entry to be created, it must be the slot through which the host is physically attached.
IP wfAhbHostSubNetMask	1.3.6.1.4.1.18.3.5.9.13.3.1.5	IpAddress	read-write	The subnet mask associated with this host entry.
wfAhbHostTable	1.3.6.1.4.1.18.3.5.9.13.3		not-accessible	A list of host entries in ATM half-bridge table.
CTR wfAhbHostTxPkts	1.3.6.1.4.1.18.3.5.9.13.3.1.10	Counter	read-only	Number of outgoing packets sent on this host entry.
INT wfAhbHostVcid	1.3.6.1.4.1.18.3.5.9.13.3.1.7	INTEGER	read-write	The ATM VPI/VCI associated with this host entry.
INT wfAhbInboundFiltDisable	1.3.6.1.4.1.18.3.5.9.13.1.7	INTEGER	read-write	Enable or disable inbound packet filtering on AHB circuits.
STR wfAhbInitFile	1.3.6.1.4.1.18.3.5.9.13.1.4	DisplayString	read-write	Name of local file containing AHB initial host entries.
INT wfAhbPolicyCct	1.3.6.1.4.1.18.3.5.9.13.4.1.4	INTEGER	read-write	The circuit number associated with policy host entry.
INT wfAhbPolicyDelete	1.3.6.1.4.1.18.3.5.9.13.4.1.1	INTEGER	read-write	Create/Delete this half-bridge policy entry.
INT wfAhbPolicyDisable	1.3.6.1.4.1.18.3.5.9.13.1.17	INTEGER	read-write	Enables or disables policy table processing.
wfAhbPolicyEntry	1.3.6.1.4.1.18.3.5.9.13.4.1		not-accessible	ATM Half Bridge Policy Entry.
INT wfAhbPolicyFlags	1.3.6.1.4.1.18.3.5.9.13.4.1.8	INTEGER	read-write	Various control flag bits for this policy entry. See router documentation for bit definitions.
IP wfAhbPolicyIpAddress	1.3.6.1.4.1.18.3.5.9.13.4.1.2	IpAddress	read-only	The IP address associated with policy host entry.
MAC wfAhbPolicyMACAddr	1.3.6.1.4.1.18.3.5.9.13.4.1.7	MacAddress	read-write	The bridge DLL header associated with this policy entry.
INT wfAhbPolicyPermission	1.3.6.1.4.1.18.3.5.9.13.4.1.9	INTEGER	read-write	Permission for creating host entry which matches this policy.
IP wfAhbPolicySubNetMask	1.3.6.1.4.1.18.3.5.9.13.4.1.3	IpAddress	read-only	The subnet mask associated with policy host entry.
wfAhbPolicyTable	1.3.6.1.4.1.18.3.5.9.13.4		not-accessible	A list of policy entries for the ATM half-bridge table.
INT wfAhbPolicyVCI	1.3.6.1.4.1.18.3.5.9.13.4.1.6	INTEGER	read-write	The ATM VCI associated with this policy entry.
INT wfAhbPolicyVPI	1.3.6.1.4.1.18.3.5.9.13.4.1.5	INTEGER	read-write	The ATM VPI associated with this policy entry.
INT wfAhbReset	1.3.6.1.4.1.18.3.5.9.13.1.8	INTEGER	read-write	Reset AHB state and remove all dynamic hosts entries from half-bridge table.
CTR wfAhbStatDropUnkPkts	1.3.6.1.4.1.18.3.5.9.13.1.13	Counter	read-only	Number of outgoing packets dropped due to unknown host.
CTR wfAhbStatFwdInPkts	1.3.6.1.4.1.18.3.5.9.13.1.15	Counter	read-only	Number of packets forwarded from AHB interfaces.
CTR wfAhbStatFwdOutPkts	1.3.6.1.4.1.18.3.5.9.13.1.12	Counter	read-only	Number of outgoing packets forwarded by half-bridge on ATM interfaces.
CTR wfAhbStatNumHostCopies	1.3.6.1.4.1.18.3.5.9.13.1.16	Counter	read-only	Number of host entries copied to other slots.
GAU wfAhbStatNumHosts	1.3.6.1.4.1.18.3.5.9.13.1.10	Gauge	read-only	Number of hosts entries maintained by half-bridge.
GAU wfAhbStatNumNets	1.3.6.1.4.1.18.3.5.9.13.1.9	Gauge	read-only	Number of IP networks advertised by half-bridge.
CTR wfAhbStatTotInPkts	1.3.6.1.4.1.18.3.5.9.13.1.14	Counter	read-only	Number of packets received on all AHB interfaces.
CTR wfAhbStatTotOutPkts	1.3.6.1.4.1.18.3.5.9.13.1.11	Counter	read-only	Number of outgoing packets sent to half-bridge from other router interfaces.

RFC description

ATM Half Bridge (AHB) function configuration including learning and file-based host entries.

Start monitoring Bay Networks Access Hub (AHB) concentrator (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BayNetworks-AHB-MIB

What Is BayNetworks-AHB-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description