BIANCA-BRICK-PPPOE-MIB

All MIBs › BIANCA-BRICK-PPPOE-MIB

Category: DSL and Broadband, Vendor: bintec

Description: Manages PPPoE client session configuration and statistics on bintec elmeg BIANCA/BRICK broadband routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BIANCA-BRICK-PPPOE-MIB?

BIANCA-BRICK-PPPOE-MIB manages PPP over Ethernet (PPPoE) client session configuration and statistics on bintec elmeg BIANCA/BRICK broadband routers, the protocol used to establish an Ethernet-based DSL/broadband WAN connection to an ISP. It exposes per-session configuration such as authentication credentials/method and session state, along with traffic counters for data sent and received over the PPPoE tunnel. Its monitoring value lies in confirming software/session health: session up/down transitions, authentication failures, and reconnect counts reveal an ISP-side outage, a credential problem, or an unstable broadband line. It depends conceptually on the underlying PPP and Ethernet interface standards, and shares indexing conventions with other BIANCA-BRICK modules. It is typically deployed on small-office/home-office BRICK routers providing broadband internet access via a PPPoE-based ISP connection. Network engineers evaluating or troubleshooting this functionality can download the BIANCA-BRICK-PPPOE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BIANCA-BRICK-PPPOE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

bintec elmeg BIANCA/BRICK broadband router

Monitoring Examples

An admin monitoring the PPPoE session status object would see the session drop and re-establish repeatedly, pointing to an unstable broadband line or an ISP authentication problem; correlating this with session traffic counters would show whether the drops coincide with high traffic load. Climbing reconnect/retry counters over time would prompt escalation to the ISP if the pattern persists.

What Can Be Monitored

PPPoE session status
authentication state
session uptime/reconnects
data traffic sent/received
connection error counts

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks

From SNMPv2-TC

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
org	1.3
dod	1.3.6
internet	1.3.6.1
private	1.3.6.1.4
enterprises	1.3.6.1.4.1
bintec	1.3.6.1.4.1.272
bibo	1.3.6.1.4.1.272.4
pppoe	1.3.6.1.4.1.272.4.24
pppoeCallTable	1.3.6.1.4.1.272.4.24.1		not-accessible	The pppoeCallTable displays all currently active PPPoE calls (incoming and outgoing). Only the system can add or remove entries to this table. Creating entries: Entries are added when an outgoing call is made or when an incoming call is connected. Deleting entries: Entries are removed once the respective call is disconnected.
pppoeCallEntry	1.3.6.1.4.1.272.4.24.1.1		not-accessible
INT pppoeCallId	1.3.6.1.4.1.272.4.24.1.1.1	INTEGER	read-only	Direction of the PPPoE call, incoming(1) or outgoing(2).
INT pppoeCallDirection	1.3.6.1.4.1.272.4.24.1.1.2	INTEGER	read-only	Direction of the PPPoE call, incoming(1) or outgoing(2).
TIK pppoeCallAge	1.3.6.1.4.1.272.4.24.1.1.3	TimeTicks	read-only	The age of the call. For outgoing calls, the time since the call began, or for incoming calls, the time since the call was received. The format is in hh:mm:ss.00.
INT pppoeCallState	1.3.6.1.4.1.272.4.24.1.1.4	INTEGER	read-write	The state of the PPPoE discovery stage according RFC 2516.
PHY pppoeCallRemotePhysAddress	1.3.6.1.4.1.272.4.24.1.1.5	PhysAddress	read-only	Peer's Ethernet address.
PHY pppoeCallLocalPhysAddress	1.3.6.1.4.1.272.4.24.1.1.6	PhysAddress	read-only	Local Ethernet Address.
STR pppoeCallAcName	1.3.6.1.4.1.272.4.24.1.1.7	DisplayString	read-only	The PPPoE access concentrator's name.
STR pppoeCallService	1.3.6.1.4.1.272.4.24.1.1.8	DisplayString	read-only	The PPPoE service name, indicating the service the Host is requesting.
CTR pppoeCallReceivedPackets	1.3.6.1.4.1.272.4.24.1.1.9	Counter	read-only	Count of received valid GRE-encapsulated packets.
CTR pppoeCallReceivedOctets	1.3.6.1.4.1.272.4.24.1.1.10	Counter	read-only	Count of received valid Octets.
CTR pppoeCallReceivedErrors	1.3.6.1.4.1.272.4.24.1.1.11	Counter	read-only	Count of received invalid GRE-encapsulated packets.
CTR pppoeCallTransmitPackets	1.3.6.1.4.1.272.4.24.1.1.12	Counter	read-only	Count of transmitted GRE-encapsulated packets.
CTR pppoeCallTransmitOctets	1.3.6.1.4.1.272.4.24.1.1.13	Counter	read-only	Count of transmitted Octets.
CTR pppoeCallTransmitErrors	1.3.6.1.4.1.272.4.24.1.1.14	Counter	read-only	Count of transmit errors.
STR pppoeCallInfo	1.3.6.1.4.1.272.4.24.1.1.15	DisplayString	read-only	Additional information to identify the PPPoE call
pppoeCreditsTable	1.3.6.1.4.1.272.4.24.2		not-accessible	The pppoeCreditsTable contains informations about current used resources and maximum allowed 'PPPoE-Service'-dependent resources. during a specified interval subsystem. Creating entries: Entries are added by the user. Deleting entries: Entries are removed by setting an entry's pppoeCreditsSurveillance object to 'delete'.
pppoeCreditsEntry	1.3.6.1.4.1.272.4.24.2.1		not-accessible
STR pppoeCreditsService	1.3.6.1.4.1.272.4.24.2.1.1	DisplayString	read-write	The PPPoE service name, indicating the service the Host is requesting.
INT pppoeCreditsSurveillance	1.3.6.1.4.1.272.4.24.2.1.2	INTEGER	read-write	Surveillance on or off.
INT pppoeCreditsMeasuretime	1.3.6.1.4.1.272.4.24.2.1.3	INTEGER	read-write	Time of one observation interval in seconds.
INT pppoeCreditsMaxInCon	1.3.6.1.4.1.272.4.24.2.1.4	INTEGER	read-write	Maximum number of allowed incoming connections during the observation interval. -1 disables this limit.
INT pppoeCreditsMaxOutCon	1.3.6.1.4.1.272.4.24.2.1.5	INTEGER	read-write	Maximum number of allowed outgoing connections during the observation interval. -1 disables this limit.
INT pppoeCreditsMaxInDuration	1.3.6.1.4.1.272.4.24.2.1.6	INTEGER	read-write	Maximum connect time for incoming connections in seconds during the observation interval. -1 disables this limit.
INT pppoeCreditsMaxOutDuration	1.3.6.1.4.1.272.4.24.2.1.7	INTEGER	read-write	Maximum connect time for outgoing connections in seconds during the observation interval. -1 disables this limit
INT pppoeCreditsTimeleft	1.3.6.1.4.1.272.4.24.2.1.8	INTEGER	read-write	Time in seconds left in current interval. Writing to Timeleft will restart the observation interval.
INT pppoeCreditsCurrentInCon	1.3.6.1.4.1.272.4.24.2.1.9	INTEGER	read-only	Current number of incoming connections.
INT pppoeCreditsCurrentOutCon	1.3.6.1.4.1.272.4.24.2.1.10	INTEGER	read-only	Current number of outgoing connections.
INT pppoeCreditsTotalInCon	1.3.6.1.4.1.272.4.24.2.1.11	INTEGER	read-only	Total count of incoming connections during the observation interval.
INT pppoeCreditsTotalOutCon	1.3.6.1.4.1.272.4.24.2.1.12	INTEGER	read-only	Total count of outgoing connections during the observation interval.
INT pppoeCreditsTotalInDuration	1.3.6.1.4.1.272.4.24.2.1.13	INTEGER	read-only	Total connect time of incoming connections during the observation interval.
INT pppoeCreditsTotalOutDuration	1.3.6.1.4.1.272.4.24.2.1.14	INTEGER	read-only	Total connect time of outgoing connections during the observation interval.
INT pppoeCreditsCurrentAccount	1.3.6.1.4.1.272.4.24.2.1.15	INTEGER	read-only	Total connect time of all outgoing connections during the observation interval calculated in percent of 'pppoeCreditsMaxOutDuration'.

RFC description

BinTec Bianca Brick PPPoE (Point-to-Point Protocol over Ethernet) MIB defining management objects for active PPPoE calls and connections.

Start monitoring bintec elmeg BIANCA/BRICK broadband routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BIANCA-BRICK-PPPOE-MIB

What Is BIANCA-BRICK-PPPOE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description