BDCOM-FLASH

All MIBs › BDCOM-FLASH

Category: Device Management, Vendor: BDCOM

Description: Manages flash memory storage on BDCOM networking devices, including file system operations and capacity reporting.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BDCOM-FLASH?

BDCOM-FLASH is a BDCOM Technology enterprise MIB for managing flash memory storage on BDCOM networking devices such as switches and access equipment. It exposes objects related to the device's file system on flash storage, including file operations and reporting of available/used flash capacity. This MIB supports monitoring the software/storage status of the device, letting administrators track flash capacity utilization and file system state, which is important for catching low storage conditions before a firmware upgrade or configuration save fails. No module description was available to confirm dependencies on other MIBs. It is deployed on BDCOM switches and access devices, typically during firmware management and configuration backup operations tracked via the BDCOM-FLASH MIB.

IPNetwork Monitor allows you to monitor SNMP objects defined in BDCOM-FLASH. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BDCOM switch
BDCOM access device

Monitoring Examples

An administrator would poll the flash file system objects to check available versus used flash capacity, catching a low-storage condition before attempting a firmware upgrade that could otherwise fail partway through. Since no sample_objects were provided in the source, specific object names are not confirmed and this describes the general monitoring use implied by the short description.

What Can Be Monitored

flash storage capacity
used vs available flash space
file system operations status

Imported Objects

From BDCOM-SMI

bdlocal

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
bdlflash	1.3.6.1.4.1.3320.2.10
INT bdflashSize	1.3.6.1.4.1.3320.2.10.1	INTEGER	read-only	Total Size in Octets of Flash memory
INT bdflashFree	1.3.6.1.4.1.3320.2.10.2	INTEGER	read-only	Unused Size in Octets of Flash memory
STR bdflashController	1.3.6.1.4.1.3320.2.10.3	DisplayString	read-only	Provides the type of Flash controller (either CCTL or CCTL2) installed in the router.
STR bdflashCard	1.3.6.1.4.1.3320.2.10.4	DisplayString	read-only	Provides the type of Flash Card installed in the router. For example, the type of Flash Card could be either CSC-MS or CSC-MC+.
INT bdflashVPP	1.3.6.1.4.1.3320.2.10.5	INTEGER	read-only	State of the VPP DIP jumper on the Flash memory card. Files can be written to the Flash memory card only if the VPP DIP jumper is turned on.
INT bdflashErase	1.3.6.1.4.1.3320.2.10.6	INTEGER	write-only	Request to erase flash memory
TIK bdflashEraseTime	1.3.6.1.4.1.3320.2.10.7	TimeTicks	read-only	Indicates the value of sysUptime the last time Flash memory was erased. If the flash had not been erased after powerup it has a value of 0 days 00:00:00.
INT bdflashEraseStatus	1.3.6.1.4.1.3320.2.10.8	INTEGER	read-only	Status of current or last flash erasing
STR bdflashToNet	1.3.6.1.4.1.3320.2.10.9	DisplayString	write-only	Write flash entry to tftp server. Value should be the name of the flash entry to send. Instance is the IP address of the tftp host.
TIK bdflashToNetTime	1.3.6.1.4.1.3320.2.10.10	TimeTicks	read-only	Indicates the value of sysUpTime the last time a file was transfered from Flash memory on the router to a TFTP host. Returns 0 days 00:00:00 if there had been no transfer since powerup.
INT bdflashToNetStatus	1.3.6.1.4.1.3320.2.10.11	INTEGER	read-only	Status of current or last flash to net transfer
STR bdnetToFlash	1.3.6.1.4.1.3320.2.10.12	DisplayString	write-only	Write flash entry from tftp server. Value should be the name of the flash entry to write. Instance is the IP address of the tftp host.
TIK bdnetToFlashTime	1.3.6.1.4.1.3320.2.10.13	TimeTicks	read-only	Indicates the value of sysUpTime the last time file was copied from a Trivial File Transfer Protocol(TFTP) server to the Flash memory on the router. Returns 0 days 00:00:00 if there had been no transfers since powerup.
INT bdnetToFlashStatus	1.3.6.1.4.1.3320.2.10.14	INTEGER	read-only	Status of current or last net to flash transfer
INT bdflashStatus	1.3.6.1.4.1.3320.2.10.15	INTEGER	read-only	Status of the availability of flash
INT bdflashEntries	1.3.6.1.4.1.3320.2.10.16	INTEGER	read-only	Number of entries in the flash directory
bdlflashFileDirTable	1.3.6.1.4.1.3320.2.10.17		not-accessible	A list of flash file entries.
bdlflashFileDirEntry	1.3.6.1.4.1.3320.2.10.17.1		not-accessible	A collection of flash eprom objects
STR bdflashDirName	1.3.6.1.4.1.3320.2.10.17.1.1	DisplayString	read-only	Name associated with the flash entry
INT bdflashDirSize	1.3.6.1.4.1.3320.2.10.17.1.2	INTEGER	read-only	Size in Octets of a flash entry
INT bdflashDirStatus	1.3.6.1.4.1.3320.2.10.17.1.3	INTEGER	read-only	Indicates the status of the entry

RFC description

Flash memory management and status monitoring for BDCOM routers.

Start monitoring BDCOM networking equipment (switches/routers) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BDCOM-FLASH

What Is BDCOM-FLASH?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description