BASP-Config-MIB

All MIBs › BASP-Config-MIB

Category: Network Interfaces, Vendor: Broadcom

Description: Manages Broadcom Advanced Server Program (BASP) NIC teaming configuration, including team type and member port assignments.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is BASP-Config-MIB?

BASP-Config-MIB manages Broadcom's Advanced Server Program (BASP), a NIC teaming/bonding technology that lets multiple physical network adapters on a server act as a single logical team for load balancing or failover. Based on its short description, it exposes configuration objects covering team type (e.g., failover, load-balancing, 802.3ad link aggregation) and the physical member NICs assigned to each team. This MIB's monitoring focus is network hardware/software configuration status -- confirming which physical adapters are currently active members of a team and whether the team is operating in its intended mode, which helps diagnose reduced throughput or a team that has lost redundancy after a NIC failure. It is a Broadcom-specific configuration MIB layered on top of the standard IF-MIB interface model used for the underlying physical NICs. It is deployed on Windows/Linux servers equipped with multiple Broadcom NICs configured for teaming in enterprise data center environments. Engineers can download the BASP-Config-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in BASP-Config-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

server with Broadcom network adapters
Broadcom NIC teaming (BASP) host

Monitoring Examples

An administrator would poll the team configuration table to check the team type assigned to a given logical team and enumerate its member NICs to confirm all expected physical adapters are present and active, though no specific object names were available in the source data to cite directly. A team member that has dropped out (e.g., after a cable fault or driver issue) would reduce the team's available bandwidth or eliminate its failover redundancy, which this MIB would surface via a reduced active-member count.

What Can Be Monitored

team type/mode configuration
team member NIC assignment
active team member count
team status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress
enterprises

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
broadcom	1.3.6.1.4.1.4413
enet	1.3.6.1.4.1.4413.1
basp	1.3.6.1.4.1.4413.1.2
baspConfig	1.3.6.1.4.1.4413.1.2.1
baspTeam	1.3.6.1.4.1.4413.1.2.1.1
INT btTeamNumber	1.3.6.1.4.1.4413.1.2.1.1.1	INTEGER	read-only	The number of loadbalance teams present on this system.
btTeamTable	1.3.6.1.4.1.4413.1.2.1.1.2		not-accessible	A list of team entries. The number of teams is given by the value of teamNumber.
btTeamEntry	1.3.6.1.4.1.4413.1.2.1.1.2.1		not-accessible	An entry containing team objects at the target system.
INT btTeamIndex	1.3.6.1.4.1.4413.1.2.1.1.2.1.1	INTEGER	not-accessible	An unique value for each team. The value for each team must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
STR btTeamName	1.3.6.1.4.1.4413.1.2.1.1.2.1.2	DisplayString	read-only	A textual string containing name of the team
INT btTeamType	1.3.6.1.4.1.4413.1.2.1.1.2.1.3	INTEGER	read-only	The type of team, distinguished according to the attribute assigned. When team has only one physical member, the team type is ignored
PHY btTeamMacAddress	1.3.6.1.4.1.4413.1.2.1.1.2.1.4	PhysAddress	read-only	Mac address of the team. Mac address is assigned to a team when the team type is team-FEC-GEC(101) or team-802-3-AD(102)
INT btPhyNumber	1.3.6.1.4.1.4413.1.2.1.1.2.1.5	INTEGER	read-only	Number of physical adapters in the team
INT btVirNumber	1.3.6.1.4.1.4413.1.2.1.1.2.1.6	INTEGER	read-only	Number of virtual adapters in the team
INT btMode	1.3.6.1.4.1.4413.1.2.1.1.2.1.7	INTEGER	read-only	mode of this team, PrimaryMode(0) or Standby(1). For team type other than team-SLB(100), this should always be PrimaryMode(0).
INT btLiveLinkEnable	1.3.6.1.4.1.4413.1.2.1.1.2.1.8	INTEGER	read-only	LiveLink is enabled or not. Probe packet can be enabled only for team-SLB(100) and team-SLB-AFD(104).
INT btLinkPacketFrequency	1.3.6.1.4.1.4413.1.2.1.1.2.1.9	INTEGER	read-only	For LiveLink feature: The frequency in milliseconds that a link packet is to be sent.
INT btLinkMaxRetry	1.3.6.1.4.1.4413.1.2.1.1.2.1.10	INTEGER	read-only	For LiveLink feature: The maximum number of retries before failing a team member.
INT btLinkRetryFrequency	1.3.6.1.4.1.4413.1.2.1.1.2.1.11	INTEGER	read-only	For LiveLink feature: The frequency (milliseconds) a link packet is to be sent after a dropped link packet is detected.
IP btLinkTargetIpAddress1	1.3.6.1.4.1.4413.1.2.1.1.2.1.12	IpAddress	read-only	For LiveLink feature: The target IP address that a link packet is sent to. A DNS name cannot be specified since there is no reliable method to resolve the DNS name without introducing unacceptable risk. Only the first one is mandatory for LiveLink. All 0 is not available.
IP btLinkTargetIpAddress2	1.3.6.1.4.1.4413.1.2.1.1.2.1.13	IpAddress	read-only	For LiveLink feature: The target IP address that a link packet is sent to. A DNS name cannot be specified since there is no reliable method to resolve the DNS name without introducing unacceptable risk. This one is optional for LiveLink. All 0 is not available.
IP btLinkTargetIpAddress3	1.3.6.1.4.1.4413.1.2.1.1.2.1.14	IpAddress	read-only	For LiveLink feature: The target IP address that a link packet is sent to. A DNS name cannot be specified since there is no reliable method to resolve the DNS name without introducing unacceptable risk. This one is optional for LiveLink. All 0 is not available.
IP btLinkTargetIpAddress4	1.3.6.1.4.1.4413.1.2.1.1.2.1.15	IpAddress	read-only	For LiveLink feature: The target IP address that a link packet is sent to. A DNS name cannot be specified since there is no reliable method to resolve the DNS name without introducing unacceptable risk. This one is optional for LiveLink. All 0 is not available.
baspPhyAdapter	1.3.6.1.4.1.4413.1.2.1.2
INT btPhyAdapterNumber	1.3.6.1.4.1.4413.1.2.1.2.1	INTEGER	read-only	Number of physical adapters presented in the physical adapter table.
btPhyAdapterTable	1.3.6.1.4.1.4413.1.2.1.2.2		not-accessible	The phyMember tables contain the physical adapter members of loadbalance teams.
btPhyAdapterEntry	1.3.6.1.4.1.4413.1.2.1.2.2.1		not-accessible	A team entry containing objects at the target system.
INT btpTeamIndex	1.3.6.1.4.1.4413.1.2.1.2.2.1.1	INTEGER	not-accessible	An unique value for each team.
INT btpAdapterIndex	1.3.6.1.4.1.4413.1.2.1.2.2.1.2	INTEGER	not-accessible	A value for each adapter within a team.
STR btpAdapterDesc	1.3.6.1.4.1.4413.1.2.1.2.2.1.3	DisplayString	read-only	A textual string containing name of the adapter
INT btpMemberType	1.3.6.1.4.1.4413.1.2.1.2.2.1.4	INTEGER	read-only	The type of adapter member.
PHY btpMacAddress	1.3.6.1.4.1.4413.1.2.1.2.2.1.5	PhysAddress	read-only	Mac address of the adapter.
INT btpMemberState	1.3.6.1.4.1.4413.1.2.1.2.2.1.6	INTEGER	read-only	State of the interface in the team.
IP btpLiveLinkIp	1.3.6.1.4.1.4413.1.2.1.2.2.1.7	IpAddress	read-only	IP address for LiveLink.
baspVirAdapter	1.3.6.1.4.1.4413.1.2.1.3
INT btVirAdapterNumber	1.3.6.1.4.1.4413.1.2.1.3.1	INTEGER	read-only	Number of virtual adapters presented in the virtual adapter table.
btVirAdapterTable	1.3.6.1.4.1.4413.1.2.1.3.2		not-accessible	The virMember tables contain the VLAN members of loadbalance teams.
btVirAdapterEntry	1.3.6.1.4.1.4413.1.2.1.3.2.1		not-accessible	A team entry containing objects at the target system.
INT btvTeamIndex	1.3.6.1.4.1.4413.1.2.1.3.2.1.1	INTEGER	not-accessible	An unique value for each team.
INT btvAdapterIndex	1.3.6.1.4.1.4413.1.2.1.3.2.1.2	INTEGER	not-accessible	A unique value for each virtual adapter in a team.
STR btvAdapterDesc	1.3.6.1.4.1.4413.1.2.1.3.2.1.3	DisplayString	read-only	A textual string containing name of the VLAN
INT btvVlanId	1.3.6.1.4.1.4413.1.2.1.3.2.1.4	INTEGER	read-only	802.1Q VLAN ID of the virtual adapter.
INT btvLinkStatus	1.3.6.1.4.1.4413.1.2.1.3.2.1.5	INTEGER	read-only	Virtual adapter link status
IP btvIPAddress	1.3.6.1.4.1.4413.1.2.1.3.2.1.6	IpAddress	read-only	IP address of the virtual adapter.
IP btvSubnetMask	1.3.6.1.4.1.4413.1.2.1.3.2.1.7	IpAddress	read-only	IP subnet Mask of the virtual adapter.
PHY btvPhysAddress	1.3.6.1.4.1.4413.1.2.1.3.2.1.8	PhysAddress	read-only	MAC address of the virtual adapter.
STR btvLineSpeed	1.3.6.1.4.1.4413.1.2.1.3.2.1.9	DisplayString	read-only	A textual string displays the operating speed of the virtual adapter.

RFC description

Vendor-private MIB for Business Adaptive Security Platform (BASP) configuration management.

Start monitoring Servers with Broadcom NICs (BASP teaming) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download BASP-Config-MIB

What Is BASP-Config-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description