All MIBs › AcGateway
Organization: AudioCodes Ltd
Last Updated: 2010-03-16
Category: Telephony and VoIP, Vendor: AudioCodes
Description: Manages AudioCodes VoIP gateway configuration and operational status, including protocol settings, channel counts, and call statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is AcGateway?
AcGateway is AudioCodes' enterprise MIB for its VoIP media gateways, used to manage protocol configuration and operational status of the gateway's telephony/VoIP functions. No sample objects or module description text were available for this entry, but per its short description it covers protocol settings (e.g., SIP/H.323/PSTN signaling configuration), channel/trunk counts, and call statistics for the gateway's voice channels. As an operational-status MIB for a telephony gateway, it is used to monitor gateway software/protocol configuration state and channel-level call activity -- active/available channel counts and call statistics -- as indicators of gateway health, though the exact leaf object names cannot be confirmed from this source data. It is part of AudioCodes' broader enterprise MIB suite (alongside modules like AcPerfMediaServices) and likely depends on shared AudioCodes system/common MIB definitions. It is deployed in enterprise and carrier VoIP networks where AudioCodes gateways bridge PSTN and IP telephony. Engineers can download the AcGateway file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in AcGateway. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- AudioCodes VoIP gateway
Monitoring Examples
Because no sample_objects were provided for this MIB in the source data, a specific object-level monitoring example cannot be grounded here. In general, an administrator would poll gateway channel/trunk status and protocol configuration objects to confirm the expected number of active voice channels and normal call statistics; this entry should be treated as based on the vendor summary rather than confirmed object names.
What Can Be Monitored
- protocol/signaling configuration state
- active voice channel/trunk count
- call statistics
- gateway operational status
This MIB depends on
Related MIBs
Imported Objects
From AUDIOCODES-TYPES-MIB
| acBoardMibs | OBJECT-IDENTITY |
| acGeneric | OBJECT-IDENTITY |
| acProducts | OBJECT-IDENTITY |
| acRegistrations | OBJECT-IDENTITY |
| audioCodes | OBJECT-IDENTITY |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From RFC1155-SMI
| IpAddress |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| RowPointer | |
| RowStatus | |
| TAddress | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| aaa | 1.3.6.1.4.1.5003.9.10.3.1.1.14 | |||
| INT aaaIndications | 1.3.6.1.4.1.5003.9.10.3.1.1.14.1 | INTEGER | read-write | Which Authentication, Authorization and Accounting indications to use. Access: Instant. AC INI-Param: AAAINDICATIONS |
| INT aaaRadiusAccountingType | 1.3.6.1.4.1.5003.9.10.3.1.1.14.2 | INTEGER | read-write | When will Radius Acounting messages be sent. Access: Instant. AC INI-Param: RADIUSACCOUNTINGTYPE |
| acBChannelNegotiationForTrunkEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.17.22.1 | not-accessible | ||
| U32 acBChannelNegotiationForTrunkIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.17.22.1.1 | Unsigned32 | not-accessible | Trunk number starting at 0. AC INI-Param: N/A |
| INT acBChannelNegotiationForTrunkMode | 1.3.6.1.4.1.5003.9.10.3.1.1.17.22.1.2 | INTEGER | read-write | ISDN B-Channel negotiation mode for trunk put MODE_NOT_SET (-1) to use BCHANNELNEGOTIATION per Gateway. Access: Instant. AC INI-Param: BCHANNELNEGOTIATIONFORTRUNK |
| acBChannelNegotiationForTrunkTable | 1.3.6.1.4.1.5003.9.10.3.1.1.17.22 | not-accessible | B-Channel Negotiation for Trunk table. | |
| INT accountAction | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT accountActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR accountContactUser | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.12 | SnmpAdminString | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_ContactUser |
| accountEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1 | not-accessible | table | |
| STR accountHostName | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.10 | SnmpAdminString | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_HostName |
| U32 accountIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.1 | Unsigned32 | read-only | . AC INI-Param: Account_Index |
| STR accountPassword | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.9 | SnmpAdminString | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_Password |
| INT accountRegister | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.11 | INTEGER | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_Register |
| ROW accountRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| accounts | 1.3.6.1.4.1.5003.9.10.3.1.1.22 | |||
| I32 accountServedIPGroup | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.6 | Integer32 | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_ServedIPGroup |
| I32 accountServedTrunkGroup | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.5 | Integer32 | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_ServedTrunkGroup |
| I32 accountServingIPGroup | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.7 | Integer32 | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_ServingIPGroup |
| accountTable | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21 | not-accessible | GwApp Accounts table | |
| STR accountUsername | 1.3.6.1.4.1.5003.9.10.3.1.1.22.21.1.8 | SnmpAdminString | read-create | GwApp Accounts table. Access: Instant. AC INI-Param: Account_Username |
| acDigitalOOSBehaviorForTrunkEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.17.23.1 | not-accessible | ||
| U32 acDigitalOOSBehaviorForTrunkIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.17.23.1.1 | Unsigned32 | not-accessible | Trunk number starting at 0. AC INI-Param: N/A |
| acDigitalOOSBehaviorForTrunkTable | 1.3.6.1.4.1.5003.9.10.3.1.1.17.23 | not-accessible | Digital OOS Behavior for Trunk table. | |
| INT acDigitalOOSBehaviorForTrunkValue | 1.3.6.1.4.1.5003.9.10.3.1.1.17.23.1.2 | INTEGER | read-write | Digital OOS Behavior for trunk put OOS_NOT_SET (-1) to use DIGITALOOSBEHAVIOR per Gateway. Access: Instant. AC INI-Param: DIGITALOOSBEHAVIORFORTRUNK |
| acEmergency | 1.3.6.1.4.1.5003.9.10.3.1.1.21 | |||
| acEmergencyNumbersEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.21.21.1 | not-accessible | ||
| U32 acEmergencyNumbersIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.21.21.1.1 | Unsigned32 | not-accessible | Emergency numbers, starting at 0. AC INI-Param: N/A |
| STR acEmergencyNumbersNumbers | 1.3.6.1.4.1.5003.9.10.3.1.1.21.21.1.2 | SnmpAdminString | read-write | Emergency numbers. Access: Instant. AC INI-Param: EmergencyNumbers |
| acEmergencyNumbersTable | 1.3.6.1.4.1.5003.9.10.3.1.1.21.21 | not-accessible | Emergency numbers table. | |
| U32 acEmergencyRegretTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.21.1 | Unsigned32 | read-write | [min] Regret time for call that is marked as Emergency. Access: Instant. AC INI-Param: EmergencyRegretTimeout |
| acGateway | 1.3.6.1.4.1.5003.9.10.3 | |||
| acGWRtcpXr | 1.3.6.1.4.1.5003.9.10.3.1.1.19 | |||
| STR acGWRtcpXrEscIP | 1.3.6.1.4.1.5003.9.10.3.1.1.19.1 | SnmpAdminString | read-write | RTCP-XR server IP address. Access: Instant. AC INI-Param: RtcpXrEscIP |
| INT acGWRtcpXrEscTransportType | 1.3.6.1.4.1.5003.9.10.3.1.1.19.3 | INTEGER | read-write | RtcpXrEsc transport type. Access: Instant. AC INI-Param: RTCPXRESCTRANSPORTTYPE |
| INT acGWRtcpXrReportMode | 1.3.6.1.4.1.5003.9.10.3.1.1.19.2 | INTEGER | read-write | 0:rtcpxr is not sent over SIP at all 1:rtcpxr is sent over sip when call ended 2:rtcpxr is sent over sip when on periodic interval and when call ended . Access: Instant. AC INI-Param: RtcpXrReportMode |
| acRemoveCallingNameForTrunkEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.17.24.1 | not-accessible | ||
| U32 acRemoveCallingNameForTrunkIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.17.24.1.1 | Unsigned32 | not-accessible | Trunk number starting at 0. AC INI-Param: N/A |
| INT acRemoveCallingNameForTrunkMode | 1.3.6.1.4.1.5003.9.10.3.1.1.17.24.1.2 | INTEGER | read-write | Remove Calling Name For Trunk table .Set (-1) to use the global parameter digitalGWextRemoveCallingName. Access: Instant. AC INI-Param: RemoveCallingNameForTrunk |
| acRemoveCallingNameForTrunkTable | 1.3.6.1.4.1.5003.9.10.3.1.1.17.24 | not-accessible | Remove Calling Name For Trunk table. | |
| acTimers | 1.3.6.1.4.1.5003.9.10.3.1.1.20 | |||
| U32 acTimersIPAlertTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.20.1 | Unsigned32 | read-write | Maximal time to wait for connect from IP (seconds). Access: Instant. AC INI-Param: IPALERTTIMEOUT |
| U32 acTimersPSTNAlertTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.20.2 | Unsigned32 | read-write | Max time (in seconds) to wait for connect from PSTN. Access: Instant. AC INI-Param: PSTNALERTTIMEOUT |
| acTWCnonAllocateablePortsEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.21.1 | not-accessible | ||
| U32 acTWCnonAllocateablePortsIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.21.1.1 | Unsigned32 | not-accessible | Line index. AC INI-Param: N/A |
| U32 acTWCnonAllocateablePortsNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.21.1.2 | Unsigned32 | read-write | Define the Ports that are not hit by 3w conference feature. Access: Instant. AC INI-Param: 3WayConfNoneAllocateablePorts |
| acTWCnonAllocateablePortsTable | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.21 | not-accessible | ||
| altRouteCause | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10 | |||
| INT altRouteCauseIP2TELAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT altRouteCauseIP2TELActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| altRouteCauseIP2TELEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21.1 | not-accessible | ||
| U32 altRouteCauseIP2TELIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: AltRouteCauseIp2Tel_Index |
| U32 altRouteCauseIP2TELReleaseCause | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21.1.5 | Unsigned32 | read-create | Release Cause. Access: Instant. AC INI-Param: AltRouteCauseIp2Tel_ReleaseCause |
| ROW altRouteCauseIP2TELRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| altRouteCauseIP2TELTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.21 | not-accessible | ||
| INT altRouteCauseTEL2IPAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT altRouteCauseTEL2IPActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| altRouteCauseTEL2IPEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22.1 | not-accessible | ||
| U32 altRouteCauseTEL2IPIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: AltRouteCauseTel2Ip_Index |
| U32 altRouteCauseTEL2IPReleaseCause | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22.1.5 | Unsigned32 | read-create | Release Cause. Access: Instant. AC INI-Param: AltRouteCauseTel2Ip_ReleaseCause |
| ROW altRouteCauseTEL2IPRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| altRouteCauseTEL2IPTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.10.22 | not-accessible | ||
| aMD | 1.3.6.1.4.1.5003.9.10.3.1.1.13 | |||
| U32 aMDTimeOut | 1.3.6.1.4.1.5003.9.10.3.1.1.13.1 | Unsigned32 | read-write | Amd Detection Timeout . Access: Instant. AC INI-Param: AMDTIMEOUT |
| analogGW | 1.3.6.1.4.1.5003.9.10.3.1.1.4 | |||
| INT analogGWEnableCurrentDisconnect | 1.3.6.1.4.1.5003.9.10.3.1.1.4.2 | INTEGER | read-write | Disconnect call upon detection of current disconnect signal. Access: Instant. AC INI-Param: ENABLECURRENTDISCONNECT |
| INT analogGWEnableReversalPolarity | 1.3.6.1.4.1.5003.9.10.3.1.1.4.1 | INTEGER | read-write | FXO: CONNECT/DISCONNECT calls upon detection of polarity signal. FXS: generate the signal. Access: Instant. AC INI-Param: ENABLEREVERSALPOLARITY |
| U32 analogGWHotLineToneDuration | 1.3.6.1.4.1.5003.9.10.3.1.1.4.4 | Unsigned32 | read-write | Duration of played hotline tone, after the gateway seizes the line in response to ringing. Access: Instant. AC INI-Param: HOTLINETONEDURATION |
| U32 analogGWRegretTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.3 | Unsigned32 | read-write | Time to wait between phone hang up and call termination. Access: Instant. AC INI-Param: REGRETTIME |
| announcement | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11 | |||
| STR announcementID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.1 | SnmpAdminString | read-write | Identification of a play voice prompt call (To be used by SIP INVITE). Access: Instant. AC INI-Param: ANNOUNCEMENTID |
| U32 announcementNumOfEndPoints | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.2 | Unsigned32 | read-write | Number of Annuncment endpoints. Access: Offline. AC INI-Param: NUMOFANNOUNCENDPOINTS |
| STR announcementToneID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.3 | SnmpAdminString | read-write | Identification of a play call progress tone call (To be used by SIP INVITE). Access: Instant. AC INI-Param: TONEID |
| INT authAction | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT authActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| authEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1 | not-accessible | ||
| U32 authIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.1 | Unsigned32 | read-only | Entry number, starting at 0. AC INI-Param: Authentication_Index |
| INT authIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.2 | INTEGER | read-write | Is this index used. Access: Offline. AC INI-Param: Authentication_IsUsed |
| U32 authModule | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.7 | Unsigned32 | read-only | Module. AC INI-Param: Authentication_Module |
| U32 authPort | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.8 | Unsigned32 | read-only | Port. AC INI-Param: Authentication_Port |
| authTable | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21 | not-accessible | ||
| STR authUserID | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.5 | SnmpAdminString | read-write | Access: Instant. AC INI-Param: Authentication_UserId |
| STR authUserPassword | 1.3.6.1.4.1.5003.9.10.3.1.2.4.21.1.6 | SnmpAdminString | read-write | Access: Instant. AC INI-Param: Authentication_UserPassword |
| INT autoDialAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT autoDialActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR autoDialDestPhoneNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.5 | SnmpAdminString | read-write | Access: Instant. AC INI-Param: TargetOfChannel_Destination |
| autoDialEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1 | not-accessible | ||
| U32 autoDialIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.1 | Unsigned32 | read-only | Entry number, starting at 0. AC INI-Param: TargetOfChannel_Index |
| INT autoDialIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.2 | INTEGER | read-write | Is this index used. AC INI-Param: TargetOfChannel_IsUsed |
| U32 autoDialModule | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.7 | Unsigned32 | read-only | Channels Module. AC INI-Param: TargetOfChannel_Module |
| U32 autoDialPort | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.8 | Unsigned32 | read-only | Channels Port. AC INI-Param: TargetOfChannel_Port |
| autoDialTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21 | not-accessible | ||
| INT autoDialType | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.21.1.6 | INTEGER | read-write | Choose auto dial type. Access: Instant. AC INI-Param: TargetOfChannel_Type |
| calea | 1.3.6.1.4.1.5003.9.10.3.1.1.5.13 | |||
| INT caleaInterceptionDirection | 1.3.6.1.4.1.5003.9.10.3.1.1.5.13.1 | INTEGER | read-write | Defines the direction of interception of a BCT listener. Access: Offline. AC INI-Param: INTERCEPTIONDIRECTION |
| INT callerDisplayAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT callerDisplayActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR callerDisplayCallerDisplay | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.5 | SnmpAdminString | read-write | Caller Name. Access: Instant. AC INI-Param: CallerDisplayInfo_DisplayString |
| callerDisplayEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1 | not-accessible | ||
| U32 callerDisplayIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.1 | Unsigned32 | read-only | Entry number, starting at 0. AC INI-Param: CallerDisplayInfo_Index |
| INT callerDisplayIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.2 | INTEGER | read-write | Is this index used. AC INI-Param: CallerDisplayInfo_IsUsed |
| U32 callerDisplayModule | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.7 | Unsigned32 | read-only | Channels Module. AC INI-Param: CallerDisplayInfo_Module |
| U32 callerDisplayPort | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.8 | Unsigned32 | read-only | Channels Port. AC INI-Param: CallerDisplayInfo_Port |
| INT callerDisplayRestriction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21.1.6 | INTEGER | read-write | Restriction. Access: Instant. AC INI-Param: CallerDisplayInfo_IsCidRestricted |
| callerDisplayTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.21 | not-accessible | ||
| callerID | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13 | |||
| INT callerIDEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.1 | INTEGER | read-write | FXS:generate CallerId siganls during ringing FXO:collect CallerId and use it in Setup message. Access: Instant. AC INI-Param: ENABLECALLERID |
| INT callerIDperPortAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT callerIDperPortActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT callerIDperPortEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.5 | INTEGER | read-write | Enable. Access: Instant. AC INI-Param: EnableCallerId_IsEnabled |
| callerIDperPortEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1 | not-accessible | ||
| U32 callerIDperPortIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.1 | Unsigned32 | read-only | . AC INI-Param: EnableCallerId_Index |
| INT callerIDperPortIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.2 | INTEGER | read-write | Is this index used. Access: Offline. AC INI-Param: EnableCallerId_IsUsed |
| U32 callerIDperPortModule | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.6 | Unsigned32 | read-only | Channels Module. AC INI-Param: EnableCallerId_Module |
| U32 callerIDperPortPort | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22.1.7 | Unsigned32 | read-only | Channels Port. AC INI-Param: EnableCallerId_Port |
| callerIDperPortTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.13.22 | not-accessible | ||
| callWaiting | 1.3.6.1.4.1.5003.9.10.3.1.1.7.11 | |||
| INT callWaitingEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.7.11.1 | INTEGER | read-write | Enable Call Waiting service. Access: Instant. AC INI-Param: ENABLECALLWAITING |
| U32 callWaitingNumberOfIndications | 1.3.6.1.4.1.5003.9.10.3.1.1.7.11.2 | Unsigned32 | read-write | Number of Call Waiting indications to be played to the user. Access: Instant. AC INI-Param: NUMBEROFWAITINGINDICATIONS |
| U32 callWaitingTimeBeforeWaitingIndications | 1.3.6.1.4.1.5003.9.10.3.1.1.7.11.5 | Unsigned32 | read-write | Time before call waiting indication is sent to a busy line (seconds). Access: Instant. AC INI-Param: TIMEBEFOREWAITINGINDICATIONS |
| U32 callWaitingTimeBetweenIndications | 1.3.6.1.4.1.5003.9.10.3.1.1.7.11.3 | Unsigned32 | read-write | Time between one call waiting indication to the next (seconds). Access: Instant. AC INI-Param: TIMEBETWEENWAITINGINDICATIONS |
| U32 callWaitingWaitingBeepDuration | 1.3.6.1.4.1.5003.9.10.3.1.1.7.11.4 | Unsigned32 | read-write | Call Waiting tone beep length (msec). Access: Instant. AC INI-Param: WAITINGBEEPDURATION |
| INT causeMapISDN2SIPAction | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT causeMapISDN2SIPActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| causeMapISDN2SIPEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1 | not-accessible | ||
| U32 causeMapISDN2SIPIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1.1 | Unsigned32 | not-accessible | AC INI-Param: CauseMapIsdn2Sip_Index |
| I32 causeMapISDN2SIPQ850Cause | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1.5 | Integer32 | read-write | Access: Instant. AC INI-Param: CauseMapIsdn2Sip_IsdnReleaseCause |
| ROW causeMapISDN2SIPRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| I32 causeMapISDN2SIPSIPResponse | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22.1.6 | Integer32 | read-write | Access: Instant. AC INI-Param: CauseMapIsdn2Sip_SipResponse |
| causeMapISDN2SIPTable | 1.3.6.1.4.1.5003.9.10.3.1.2.9.22 | not-accessible | Cause Map SIP to ISDN Table. | |
| INT causeMapSIP2ISDNAction | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT causeMapSIP2ISDNActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| causeMapSIP2ISDNEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1 | not-accessible | ||
| U32 causeMapSIP2ISDNIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1.1 | Unsigned32 | not-accessible | AC INI-Param: CauseMapSip2Isdn_Index |
| I32 causeMapSIP2ISDNQ850Cause | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1.6 | Integer32 | read-write | Access: Instant. AC INI-Param: CauseMapSip2Isdn_IsdnReleaseCause |
| ROW causeMapSIP2ISDNRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| I32 causeMapSIP2ISDNSIPResponse | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21.1.5 | Integer32 | read-write | Access: Instant. AC INI-Param: CauseMapSip2Isdn_SipResponse |
| causeMapSIP2ISDNTable | 1.3.6.1.4.1.5003.9.10.3.1.2.9.21 | not-accessible | Cause Map SIP to ISDN Table. | |
| INT channelsAction | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT channelsActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| channelsEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1 | not-accessible | ||
| U32 channelsIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.1 | Unsigned32 | not-accessible | Channel numbers, starting at 0. AC INI-Param: TrunkGroup_Index |
| U32 channelsLastCh | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.7 | Unsigned32 | read-create | Last Channel for the trunk/hunt group. Access: Instant. AC INI-Param: TrunkGroup_LastBChannel |
| U32 channelsLastTrunkID | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.11 | Unsigned32 | read-create | Last Trunk/Hunt group ID. Access: Instant. AC INI-Param: TrunkGroup_LastTrunkId |
| U32 channelsModule | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.12 | Unsigned32 | read-create | Channels Module. Access: Instant. AC INI-Param: TrunkGroup_Module |
| U32 channelsProfileID | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.10 | Unsigned32 | read-create | Profile ID. Access: Instant. AC INI-Param: TrunkGroup_ProfileId |
| ROW channelsRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| channelsSetting | 1.3.6.1.4.1.5003.9.10.3.1.1.1 | |||
| INT channelsSettingSelectMode | 1.3.6.1.4.1.5003.9.10.3.1.1.1.1 | INTEGER | read-write | Default method to use for trunk B-channel allocation (IP to Tel calls). Access: Instant. AC INI-Param: CHANNELSELECTMODE |
| U32 channelsStartingCh | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.6 | Unsigned32 | read-create | Starting Channel for this trunk/hunt group. Access: Instant. AC INI-Param: TrunkGroup_FirstBChannel |
| STR channelsStartingPhoneNum | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.8 | SnmpAdminString | read-create | Starting Phone Number. Access: Instant. AC INI-Param: TrunkGroup_FirstPhoneNumber |
| channelsTable | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21 | not-accessible | The table defines trunk/hunt groups and phone numbers for gateway endpoints. The endpoints that aren�t defined will be disabled. | |
| U32 channelsTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.9 | Unsigned32 | read-create | Trunk/Hunt group ID. Access: Instant. AC INI-Param: TrunkGroup_TrunkGroupNum |
| U32 channelsTrunkID | 1.3.6.1.4.1.5003.9.10.3.1.1.1.21.1.5 | Unsigned32 | read-create | Trunk/Hunt group ID. Access: Instant. AC INI-Param: TrunkGroup_FirstTrunkId |
| INT chargeCodesAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT chargeCodesActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| chargeCodesEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1 | not-accessible | ||
| U32 chargeCodesIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.1 | Unsigned32 | not-accessible | Charge code index. AC INI-Param: ChargeCode_Index |
| U32 chargeCodesPeriod1EndTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.5 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_EndTime1 |
| U32 chargeCodesPeriod1PulseInterval | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.6 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulseInterval1 |
| U32 chargeCodesPeriod1PulsesOnAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.7 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulsesOnAnswer1 |
| U32 chargeCodesPeriod2EndTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.8 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_EndTime2 |
| U32 chargeCodesPeriod2PulseInterval | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.9 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulseInterval2 |
| U32 chargeCodesPeriod2PulsesOnAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.10 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulsesOnAnswer2 |
| U32 chargeCodesPeriod3EndTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.11 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_EndTime3 |
| U32 chargeCodesPeriod3PulseInterval | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.12 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulseInterval3 |
| U32 chargeCodesPeriod3PulsesOnAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.13 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulsesOnAnswer3 |
| U32 chargeCodesPeriod4EndTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.14 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_EndTime4 |
| U32 chargeCodesPeriod4PulseInterval | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.15 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulseInterval4 |
| U32 chargeCodesPeriod4PulsesOnAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.16 | Unsigned32 | read-create | Access: Instant. AC INI-Param: ChargeCode_PulsesOnAnswer4 |
| ROW chargeCodesRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| chargeCodesTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.21 | not-accessible | ||
| coders | 1.3.6.1.4.1.5003.9.10.3.1.1.6 | |||
| INT codersAction | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT codersActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| codersEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1 | not-accessible | ||
| INT codersGroup0Action | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.3 | INTEGER | read-create | Mangement Field for ACTIONS. AC INI-Param: N/A |
| INT codersGroup0ActionRes | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.4 | INTEGER | read-only | Mangement Field for ACTIONS RESULT. AC INI-Param: N/A |
| codersGroup0Entry | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1 | not-accessible | ||
| U32 codersGroup0Index | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.1 | Unsigned32 | not-accessible | Index Field for line. AC INI-Param: CodersGroup0_Index |
| INT codersGroup0Name | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.5 | INTEGER | read-create | Coders Group name. Access: Instant. AC INI-Param: CodersGroup0_Name |
| U32 codersGroup0PacketizationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.6 | Unsigned32 | read-create | Coders Group packetization time. Access: Instant. AC INI-Param: CodersGroup0_pTime |
| I32 codersGroup0PayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.8 | Integer32 | read-create | Coders Group payload type. Access: Instant. AC INI-Param: CodersGroup0_PayloadType |
| U32 codersGroup0Rate | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.7 | Unsigned32 | read-create | Coders Group rate. Access: Instant. AC INI-Param: CodersGroup0_rate |
| ROW codersGroup0RowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.2 | RowStatus | read-create | ROWSTATUS field for line. AC INI-Param: N/A |
| INT codersGroup0SilenceSuppression | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2.1.9 | INTEGER | read-create | Coders Group silence suppression. Access: Instant. AC INI-Param: CodersGroup0_Sce |
| codersGroup0Table | 1.3.6.1.4.1.5003.9.10.3.1.1.6.2 | not-accessible | ||
| INT codersGroup1Action | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.3 | INTEGER | read-create | Mangement Field for ACTIONS. AC INI-Param: N/A |
| INT codersGroup1ActionRes | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.4 | INTEGER | read-only | Mangement Field for ACTIONS RESULT. AC INI-Param: N/A |
| codersGroup1Entry | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1 | not-accessible | ||
| U32 codersGroup1Index | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.1 | Unsigned32 | not-accessible | Index Field for line. AC INI-Param: CodersGroup1_Index |
| INT codersGroup1Name | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.5 | INTEGER | read-create | Coders Group name. Access: Instant. AC INI-Param: CodersGroup1_Name |
| U32 codersGroup1PacketizationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.6 | Unsigned32 | read-create | Coders Group packetization time. Access: Instant. AC INI-Param: CodersGroup1_pTime |
| U32 codersGroup1PayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.8 | Unsigned32 | read-create | Coders Group payload type. Access: Instant. AC INI-Param: CodersGroup1_PayloadType |
| U32 codersGroup1Rate | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.7 | Unsigned32 | read-create | Coders Group rate. Access: Instant. AC INI-Param: CodersGroup1_rate |
| ROW codersGroup1RowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.2 | RowStatus | read-create | ROWSTATUS field for line. AC INI-Param: N/A |
| INT codersGroup1SilenceSuppression | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3.1.9 | INTEGER | read-create | Coders Group silence suppression. Access: Instant. AC INI-Param: CodersGroup1_Sce |
| codersGroup1Table | 1.3.6.1.4.1.5003.9.10.3.1.1.6.3 | not-accessible | ||
| INT codersGroup2Action | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.3 | INTEGER | read-create | Mangement Field for ACTIONS. AC INI-Param: N/A |
| INT codersGroup2ActionRes | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.4 | INTEGER | read-only | Mangement Field for ACTIONS RESULT. AC INI-Param: N/A |
| codersGroup2Entry | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1 | not-accessible | ||
| U32 codersGroup2Index | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.1 | Unsigned32 | not-accessible | Index Field for line. AC INI-Param: CodersGroup2_Index |
| INT codersGroup2Name | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.5 | INTEGER | read-create | Coders Group name. Access: Instant. AC INI-Param: CodersGroup2_Name |
| U32 codersGroup2PacketizationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.6 | Unsigned32 | read-create | Coders Group packetization time. Access: Instant. AC INI-Param: CodersGroup2_pTime |
| I32 codersGroup2PayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.8 | Integer32 | read-create | Coders Group payload type. Access: Instant. AC INI-Param: CodersGroup2_PayloadType |
| U32 codersGroup2Rate | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.7 | Unsigned32 | read-create | Coders Group rate. Access: Instant. AC INI-Param: CodersGroup2_rate |
| ROW codersGroup2RowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.2 | RowStatus | read-create | ROWSTATUS field for line. AC INI-Param: N/A |
| INT codersGroup2SilenceSuppression | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4.1.9 | INTEGER | read-create | Coders Group silence suppression. Access: Instant. AC INI-Param: CodersGroup2_Sce |
| codersGroup2Table | 1.3.6.1.4.1.5003.9.10.3.1.1.6.4 | not-accessible | ||
| INT codersGroup3Action | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.3 | INTEGER | read-create | Mangement Field for ACTIONS. AC INI-Param: N/A |
| INT codersGroup3ActionRes | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.4 | INTEGER | read-only | Mangement Field for ACTIONS RESULT. AC INI-Param: N/A |
| codersGroup3Entry | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1 | not-accessible | ||
| U32 codersGroup3Index | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.1 | Unsigned32 | not-accessible | Index Field for line. AC INI-Param: CodersGroup3_Index |
| INT codersGroup3Name | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.5 | INTEGER | read-create | Coders Group name. Access: Instant. AC INI-Param: CodersGroup3_Name |
| U32 codersGroup3PacketizationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.6 | Unsigned32 | read-create | Coders Group packetization time. Access: Instant. AC INI-Param: CodersGroup3_pTime |
| I32 codersGroup3PayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.8 | Integer32 | read-create | Coders Group payload type. Access: Instant. AC INI-Param: CodersGroup3_PayloadType |
| U32 codersGroup3Rate | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.7 | Unsigned32 | read-create | Coders Group rate. Access: Instant. AC INI-Param: CodersGroup3_rate |
| ROW codersGroup3RowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.2 | RowStatus | read-create | ROWSTATUS field for line. AC INI-Param: N/A |
| INT codersGroup3SilenceSuppression | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5.1.9 | INTEGER | read-create | Coders Group silence suppression. Access: Instant. AC INI-Param: CodersGroup3_Sce |
| codersGroup3Table | 1.3.6.1.4.1.5003.9.10.3.1.1.6.5 | not-accessible | ||
| INT codersGroup4Action | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.3 | INTEGER | read-create | Mangement Field for ACTIONS. AC INI-Param: N/A |
| INT codersGroup4ActionRes | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.4 | INTEGER | read-only | Mangement Field for ACTIONS RESULT. AC INI-Param: N/A |
| codersGroup4Entry | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1 | not-accessible | ||
| U32 codersGroup4Index | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.1 | Unsigned32 | not-accessible | Index Field for line. AC INI-Param: CodersGroup4_Index |
| INT codersGroup4Name | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.5 | INTEGER | read-create | Coders Group name. Access: Instant. AC INI-Param: CodersGroup4_Name |
| U32 codersGroup4PacketizationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.6 | Unsigned32 | read-create | Coders Group packetization time. Access: Instant. AC INI-Param: CodersGroup4_pTime |
| I32 codersGroup4PayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.8 | Integer32 | read-create | Coders Group payload type. Access: Instant. AC INI-Param: CodersGroup4_PayloadType |
| U32 codersGroup4Rate | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.7 | Unsigned32 | read-create | Coders Group rate. Access: Instant. AC INI-Param: CodersGroup4_rate |
| ROW codersGroup4RowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.2 | RowStatus | read-create | ROWSTATUS field for line. AC INI-Param: N/A |
| INT codersGroup4SilenceSuppression | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6.1.9 | INTEGER | read-create | Coders Group silence suppression. Access: Instant. AC INI-Param: CodersGroup4_Sce |
| codersGroup4Table | 1.3.6.1.4.1.5003.9.10.3.1.1.6.6 | not-accessible | ||
| U32 codersIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: CoderName_Index |
| U32 codersInterval | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.6 | Unsigned32 | read-create | Coder Interval. Access: Offline. AC INI-Param: CoderName_PacketInterval |
| INT codersName | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.5 | INTEGER | read-create | Coder Name. Access: Offline. AC INI-Param: N/A |
| U32 codersPayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.8 | Unsigned32 | read-create | Payload type. Access: Offline. AC INI-Param: CoderName_PayloadType |
| U32 codersRate | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.7 | Unsigned32 | read-create | Rate in bit per second. Access: Offline. AC INI-Param: CoderName_rate |
| ROW codersRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| INT codersSilenceSuppression | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1.1.9 | INTEGER | read-create | Silence Suppression. Access: Offline. AC INI-Param: CoderName_Sce |
| codersTable | 1.3.6.1.4.1.5003.9.10.3.1.1.6.1 | not-accessible | The names of the five possible coders. | |
| common | 1.3.6.1.4.1.5003.9.10.3.1.1 | |||
| conference | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10 | |||
| INT conference3WayMode | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.5 | INTEGER | read-write | If 3wayConferenceMode=0, the usual conference mode will be used, this mode wil be compatible with our IPmedia server. The INVITE messages that are used to form a conference call, all will contain the same conIfD in sip INVITE requests. If 3wayConferenceMode=1, only the first INVITE send to conference server will use the confID. In contact header of 200OK response, the conference server returns a conference URI. This conference URI will be included (by our MP gateway) in REFER-TO header in the REFER messages, send by the MP GW to other sip clients. The sip client will join to conference by sending INVITEs to the conference server using this conference URI . 3wayConferenceMode = 2: InBoard 3w Conference. Access: Instant. AC INI-Param: 3WAYCONFERENCEMODE |
| INT conferenceBipOnConference | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.2 | INTEGER | read-write | Beep when a new participant joins a conference. Access: Instant. AC INI-Param: BIPONCONFERENCE |
| INT conferenceEnableDTMFClamping | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.4 | INTEGER | read-write | EnableConferenceDTMFClamp - if enable remove detected DTMF digits from the audio stream on simple conference participant. Access: Instant. AC INI-Param: EnableConferenceDTMFClamp |
| INT conferenceEnableDTMFReporting | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.3 | INTEGER | read-write | EnableConferenceDTMFReporting- if enable report in out of band format about detected DTMF digits (values 1-Report,0 - Not Report). Access: Instant. AC INI-Param: EnableConferenceDTMFReporting |
| STR conferenceID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.1 | SnmpAdminString | read-write | Identification of conference call (To be used by SIP INVITE). Access: Instant. AC INI-Param: CONFERENCEID |
| U32 conferenceMaxInBoardCalls | 1.3.6.1.4.1.5003.9.10.3.1.1.5.10.6 | Unsigned32 | read-write | Max InBoard Conference Calls. Access: Offline. AC INI-Param: MaxInBoardConferenceCalls |
| connectivityQos | 1.3.6.1.4.1.5003.9.10.3.1.1.2.22 | |||
| U32 connectivityQosEffectivePeriod | 1.3.6.1.4.1.5003.9.10.3.1.1.2.22.3 | Unsigned32 | read-write | if during this period [in seconds], no updated qos info received, theold qos info is discarded. if qos poor, and no calls alowed, after this period, calls will be allowed again. Access: Instant. AC INI-Param: IPCONNQOSEFFECTIVEPERIOD |
| U32 connectivityQosMaxAllowedDelay | 1.3.6.1.4.1.5003.9.10.3.1.1.2.22.2 | Unsigned32 | read-write | The maximum delay that will not prevent normal routing (msec). Access: Instant. AC INI-Param: IPCONNQOSMAXALLOWEDDELAY |
| U32 connectivityQosMaxAllowedPL | 1.3.6.1.4.1.5003.9.10.3.1.1.2.22.1 | Unsigned32 | read-write | The maximum percentage of packet loss that will not prevent normal routing. Access: Instant. AC INI-Param: IPCONNQOSMAXALLOWEDPL |
| U32 connectivityQosSamplesToAvarage | 1.3.6.1.4.1.5003.9.10.3.1.1.2.22.4 | Unsigned32 | read-write | number of samples to avarage. in other words define the weiught of the new sample. Access: Instant. AC INI-Param: IPCONNQOSSAMPLESTOAVARAGE |
| dialing | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12 | |||
| I32 dialingDialPlanIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.6 | Integer32 | read-write | Defines the plan index to be used from the external Dial Plan file. Access: Instant. AC INI-Param: DIALPLANINDEX |
| STR dialingDigitMapping | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.4 | SnmpAdminString | read-write | The digit map patterns separated by a vertical bar (|), as defined in the MEGACO RFC. Access: Instant. AC INI-Param: DIGITMAPPING |
| INT dialingEnableDigitDelivery | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.5 | INTEGER | read-write | Enable automatic digit delivery to Tel side after line is off-hooked or seized. Access: Offline. AC INI-Param: ENABLEDIGITDELIVERY |
| INT dialingIsSpecialDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.3 | INTEGER | read-write | When disabled, pressing special digits (* or #) will terminate digit collection. When enabled, special digits can be received as part of the dialed number or Endpoint phone number. Access: Instant. AC INI-Param: ISSPECIALDIGITS |
| U32 dialingMaxDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.1 | Unsigned32 | read-write | Maximum number of digits before dialing starts. Access: Instant. AC INI-Param: MAXDIGITS |
| U32 dialingTimeBetweenDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.4.12.2 | Unsigned32 | read-write | Timeout in seconds between dialed digits. Access: Instant. AC INI-Param: TIMEBETWEENDIGITS |
| dID | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16 | |||
| U32 dIDDelayBeforeDidWink | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.3 | Unsigned32 | read-write | delay between Off-Hook detection and Wink generation (relevant only for FXS). unit - ms. Access: Instant. AC INI-Param: DELAYBEFOREDIDWINK |
| INT dIDEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.1 | INTEGER | read-write | Enable DID support. Access: Instant. AC INI-Param: ENABLEDID |
| INT dIDEnableWink | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.2 | INTEGER | read-write | Enable support for DID lines using Wink. Access: Instant. AC INI-Param: ENABLEDIDWINK |
| digitalGW | 1.3.6.1.4.1.5003.9.10.3.1.1.3 | |||
| INT digitalGWBChannelNegotiation | 1.3.6.1.4.1.5003.9.10.3.1.1.3.1 | INTEGER | read-write | ISDN B-Channel negotiation mode. Access: Instant. AC INI-Param: BCHANNELNEGOTIATION |
| INT digitalGWCASSendHookFlash | 1.3.6.1.4.1.5003.9.10.3.1.1.3.6 | INTEGER | read-write | 0 (default): Hookflash not forwarded 1:HookFlash forwarded - Testing. Access: Instant. AC INI-Param: CASSENDHOOKFLASH |
| INT digitalGWConnectOnProgressInd | 1.3.6.1.4.1.5003.9.10.3.1.1.3.12 | INTEGER | read-write | FXS:generate CallerId siganls during ringing FXO:collect CallerId and use it in Setup message. Access: Instant. AC INI-Param: CONNECTONPROGRESSIND |
| INT digitalGWEnableCallingPartyCategory | 1.3.6.1.4.1.5003.9.10.3.1.1.3.19 | INTEGER | read-write | Enables NI2 calling party category translation to SIP. Access: Instant. AC INI-Param: ENABLECALLINGPARTYCATEGORY |
| INT digitalGWEnableISDNTunnelingIp2Tel | 1.3.6.1.4.1.5003.9.10.3.1.1.3.18 | INTEGER | read-write | Enable ISDN tunneling to pass Setup and Facility messages from IP to ISDN. Access: Instant. AC INI-Param: ENABLEISDNTUNNELINGIP2TEL |
| INT digitalGWEnableISDNTunnelingTel2Ip | 1.3.6.1.4.1.5003.9.10.3.1.1.3.17 | INTEGER | read-write | Enable ISDN tunneling to pass Setup and Facility messages from ISDN to IP. Access: Instant. AC INI-Param: ENABLEISDNTUNNELINGTEL2IP |
| INT digitalGWEnableTDMOverIp | 1.3.6.1.4.1.5003.9.10.3.1.1.3.8 | INTEGER | read-write | Enable gateway to maintain a permanent RTP connection. Access: Offline. AC INI-Param: ENABLETDMOVERIP |
| INT digitalGWEnableTransferCap | 1.3.6.1.4.1.5003.9.10.3.1.1.3.3 | INTEGER | read-write | Select Transfer Capabilities method between H.323/Q.931 and ISDN/Q.931. Access: Instant. AC INI-Param: ENABLETRANSFERCAP |
| INT digitalGWEnableUuiIp2Tel | 1.3.6.1.4.1.5003.9.10.3.1.1.3.15 | INTEGER | read-write | Enable User-User IE to pass in Setup from IP to ISDN. Access: Instant. AC INI-Param: ENABLEUUIIP2TEL |
| INT digitalGWEnableUuiTel2Ip | 1.3.6.1.4.1.5003.9.10.3.1.1.3.14 | INTEGER | read-write | Enable User-User IE to pass in Setup from ISDN to IP. Access: Instant. AC INI-Param: ENABLEUUITEL2IP |
| digitalGWext | 1.3.6.1.4.1.5003.9.10.3.1.1.17 | |||
| INT digitalGWextCopyDest2RedirectNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.17.7 | INTEGER | read-write | 0 - Redirect N not affected,1- Called N after manipulation from TEL2IP call will also be used as Redirect N,2 - the Called N before manipulation - as Redirect N. Access: Instant. AC INI-Param: COPYDEST2REDIRECTNUMBER |
| U32 digitalGWextDefaultCauseMapISDN2IP | 1.3.6.1.4.1.5003.9.10.3.1.1.17.3 | Unsigned32 | read-write | All ISDN release causes except normal, busy, no user responding, and no answer will be mapped to this cause, if set. Access: Instant. AC INI-Param: DEFAULTCAUSEMAPISDN2IP |
| INT digitalGWextEnableAoC | 1.3.6.1.4.1.5003.9.10.3.1.1.17.5 | INTEGER | read-write | Enable AoC-D and AoC-E from ISDN to SIP. Access: Instant. AC INI-Param: ENABLEAOC |
| INT digitalGWextEnableQSIGTunneling | 1.3.6.1.4.1.5003.9.10.3.1.1.17.1 | INTEGER | read-write | Enables QSIG Tunneling over SIP. Access: Instant. AC INI-Param: ENABLEQSIGTUNNELING |
| INT digitalGWextISDNSubaddressFormat | 1.3.6.1.4.1.5003.9.10.3.1.1.17.4 | INTEGER | read-write | ISDN SubAdress format. Access: Instant. AC INI-Param: ISDNSUBADDRESSFORMAT |
| INT digitalGWextRemoveCallingName | 1.3.6.1.4.1.5003.9.10.3.1.1.17.6 | INTEGER | read-write | If set to 1 - Removes Calling Name from IP->TEL calls. Access: Instant. AC INI-Param: REMOVECALLINGNAME |
| INT digitalGWextRemoveCLIWhenRestricted | 1.3.6.1.4.1.5003.9.10.3.1.1.17.2 | INTEGER | read-write | Removes CLI from IP->TEL calls if received CLI is restricted. Access: Instant. AC INI-Param: REMOVECLIWHENRESTRICTED |
| U32 digitalGWextTDMOverIPMinCallsForTrunkActivation | 1.3.6.1.4.1.5003.9.10.3.1.1.17.8 | Unsigned32 | read-write | Minimum connected calls for trunk activation while in TDMOverIPMode if 0 - trunk is always active. Access: Instant. AC INI-Param: TDMOVERIPMINCALLSFORTRUNKACTIVATION |
| INT digitalGWISDNRxOverlap | 1.3.6.1.4.1.5003.9.10.3.1.1.3.5 | INTEGER | read-write | Enable reception of overlap dialing from ISDN side. Access: Instant. AC INI-Param: ISDNRXOVERLAP |
| INT digitalGWISDNTransferCapability | 1.3.6.1.4.1.5003.9.10.3.1.1.3.7 | INTEGER | read-write | Send transfer capability to ISDN side on setup message -1:Do not Overwrite 0:Audio 3.1 1:Speech 2:Data 3:Audio. Access: Instant. AC INI-Param: ISDNTRANSFERCAPABILITY |
| INT digitalGWLocalISDNRBSource | 1.3.6.1.4.1.5003.9.10.3.1.1.3.13 | INTEGER | read-write | If the ringback tone source is not IP, who should supply the Ringback tone. 0 - PBX/PSTN (default) ; 1- GW. Access: Instant. AC INI-Param: LOCALISDNRBSOURCE |
| I32 digitalGWPIForDisconnectMsg | 1.3.6.1.4.1.5003.9.10.3.1.1.3.11 | Integer32 | read-write | Configure PIForDisconnectMsg in order to overwrite PI value received in ISDN Disconnect message. Access: Instant. AC INI-Param: PIFORDISCONNECTMSG |
| INT digitalGWPlayRBTOnISDNTransfer | 1.3.6.1.4.1.5003.9.10.3.1.1.3.40 | INTEGER | read-write | Play local RBT on TBCT/ECT/RLT transfer. Access: Instant. AC INI-Param: PLAYRBTONISDNTRANSFER |
| U32 digitalGWR2Category | 1.3.6.1.4.1.5003.9.10.3.1.1.3.4 | Unsigned32 | read-write | MFC\R2 Calling Party's category. Access: Instant. AC INI-Param: R2CATEGORY |
| INT digitalGWSendISDNTransferOnConnect | 1.3.6.1.4.1.5003.9.10.3.1.1.3.16 | INTEGER | read-write | Send TBCT/ECT/RLT request only when second leg call is connected. Access: Instant. AC INI-Param: SENDISDNTRANSFERONCONNECT |
| INT digitalGWSupportRedirectInFacility | 1.3.6.1.4.1.5003.9.10.3.1.1.3.10 | INTEGER | read-write | Search for redirect number in facility IE. Access: Instant. AC INI-Param: SUPPORTREDIRECTINFACILITY |
| INT digitalGWSwapRedirectNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.3.2 | INTEGER | read-write | Swap Redirect and Called numbers. Access: Instant. AC INI-Param: SWAPREDIRECTNUMBER |
| INT digitalGWTransparentCoderOnDataCall | 1.3.6.1.4.1.5003.9.10.3.1.1.3.9 | INTEGER | read-write | In case the transfer capability of a call from ISDN is data open with transparent coder. Access: Instant. AC INI-Param: TRANSPARENTCODERONDATACALL |
| INT dnsInfoAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT dnsInfoActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR dnsInfoDomainName | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.5 | SnmpAdminString | read-create | Domain Name. Access: Instant. AC INI-Param: Dns2Ip_DomainName |
| dnsInfoEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1 | not-accessible | ||
| STR dnsInfoFirstIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.6 | SnmpAdminString | read-create | IP Address. Access: Instant. AC INI-Param: Dns2Ip_FirstIpAddress |
| STR dnsInfoFourthIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.9 | SnmpAdminString | read-create | IP Address. Access: Instant. AC INI-Param: Dns2Ip_FourthIpAddress |
| U32 dnsInfoIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: Dns2Ip_Index |
| ROW dnsInfoRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| STR dnsInfoSecondIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.7 | SnmpAdminString | read-create | IP Address. Access: Instant. AC INI-Param: Dns2Ip_SecondIpAddress |
| dnsInfoTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3 | not-accessible | ||
| STR dnsInfoThirdIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.3.1.8 | SnmpAdminString | read-create | IP Address. Access: Instant. AC INI-Param: Dns2Ip_ThirdIpAddress |
| INT dstIP2TELAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT dstIP2TELActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| dstIP2TELEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1 | not-accessible | ||
| U32 dstIP2TELIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.1 | Unsigned32 | not-accessible | Destination number, starting at 0. AC INI-Param: NumberMapIp2Tel_Index |
| U32 dstIP2TELIsPresentationRestricted | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.15 | Unsigned32 | read-create | Is Presentation Restricted. Access: Instant. AC INI-Param: NumberMapIp2Tel_IsPresentationRestricted |
| INT dstIP2TELNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.9 | INTEGER | read-create | Number Plan. Access: Instant. AC INI-Param: NumberMapIp2Tel_NumberPlan |
| INT dstIP2TELNumberType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.10 | INTEGER | read-create | Number Type. Access: Instant. AC INI-Param: NumberMapIp2Tel_NumberType |
| U32 dstIP2TELNumOfDigitsToLeave | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.8 | Unsigned32 | read-create | Number of digits to leave. Access: Instant. AC INI-Param: NumberMapIp2Tel_LeaveFromRight |
| U32 dstIP2TELNumOfDigitsToRemFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.13 | Unsigned32 | read-create | Num Of digits To Remove from Right. Access: Instant. AC INI-Param: NumberMapIp2Tel_RemoveFromRight |
| U32 dstIP2TELNumOfStrippedDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.6 | Unsigned32 | read-create | Num of stripped digits, Remove from left. Access: Instant. AC INI-Param: NumberMapIp2Tel_RemoveFromLeft |
| STR dstIP2TELPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: NumberMapIp2Tel_DestinationPrefix |
| STR dstIP2TELPrefixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.7 | SnmpAdminString | read-create | Prefix to Add. Access: Instant. AC INI-Param: NumberMapIp2Tel_Prefix2Add |
| ROW dstIP2TELRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR dstIP2TELSourceIP | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.12 | SnmpAdminString | read-create | Source IP. Access: Instant. AC INI-Param: NumberMapIp2Tel_SourceAddress |
| STR dstIP2TELSourcePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.11 | SnmpAdminString | read-create | Source Prefix. Access: Instant. AC INI-Param: NumberMapIp2Tel_SourcePrefix |
| STR dstIP2TELSuffix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21.1.14 | SnmpAdminString | read-create | Suffix To Add. Access: Instant. AC INI-Param: NumberMapIp2Tel_Suffix2Add |
| dstIP2TELTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.21 | not-accessible | ||
| INT dstTEL2IPAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT dstTEL2IPActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| dstTEL2IPEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1 | not-accessible | ||
| U32 dstTEL2IPIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.1 | Unsigned32 | not-accessible | Destination number, starting at 0. AC INI-Param: NumberMapTel2Ip_Index |
| U32 dstTEL2IPIsPresentationRestricted | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.14 | Unsigned32 | read-create | Is Presentation Restricted. Access: Instant. AC INI-Param: NumberMapTel2Ip_IsPresentationRestricted |
| INT dstTEL2IPNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.9 | INTEGER | read-create | Number Plan. Access: Instant. AC INI-Param: NumberMapTel2Ip_NumberPlan |
| INT dstTEL2IPNumberType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.10 | INTEGER | read-create | Number Type. Access: Instant. AC INI-Param: NumberMapTel2Ip_NumberType |
| U32 dstTEL2IPNumOfDigitsToLeave | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.8 | Unsigned32 | read-create | Number of digits to leave. Access: Instant. AC INI-Param: NumberMapTel2Ip_LeaveFromRight |
| U32 dstTEL2IPNumOfDigitsToRemFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.12 | Unsigned32 | read-create | Num Of digits To Remove from Right. Access: Instant. AC INI-Param: NumberMapTel2Ip_RemoveFromRight |
| U32 dstTEL2IPNumOfStrippedDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.6 | Unsigned32 | read-create | Num of stripped digits. Access: Instant. AC INI-Param: NumberMapTel2Ip_RemoveFromLeft |
| STR dstTEL2IPPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: NumberMapTel2Ip_DestinationPrefix |
| STR dstTEL2IPPrefixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.7 | SnmpAdminString | read-create | Prefix to Add. Access: Instant. AC INI-Param: NumberMapTel2Ip_Prefix2Add |
| ROW dstTEL2IPRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR dstTEL2IPSourceIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.15 | SnmpAdminString | read-create | Source Address. Access: Instant. AC INI-Param: NumberMapTel2Ip_SourceAddress |
| I32 dstTEL2IPSourceIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.17 | Integer32 | read-create | GwApp Tel-to-IP Destination Phone Number Manipulation Rules Table. Access: Instant. AC INI-Param: NumberMapTel2Ip_SrcIPGroupID |
| STR dstTEL2IPSourcePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.11 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: NumberMapTel2Ip_SourcePrefix |
| I32 dstTEL2IPSourceTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.16 | Integer32 | read-create | GwApp Tel-to-IP Destination Phone Number Manipulation Rules Table. Access: Instant. AC INI-Param: NumberMapTel2Ip_SrcTrunkGroupID |
| STR dstTEL2IPSuffix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22.1.13 | SnmpAdminString | read-create | Suffix To Add. Access: Instant. AC INI-Param: NumberMapTel2Ip_Suffix2Add |
| dstTEL2IPTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.22 | not-accessible | ||
| INT dTMFOptionsAction | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT dTMFOptionsActionResult | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| dTMFOptionsEntry | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21.1 | not-accessible | ||
| U32 dTMFOptionsIndex | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: N/A |
| ROW dTMFOptionsRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21.1.2 | RowStatus | read-create | This object allows entries to be created and deleted from the table. For Reference: RFC 1903, Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2). Access: Instant. AC INI-Param: N/A |
| dTMFOptionsTable | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21 | not-accessible | The names of the five possible coders. | |
| INT dTMFOptionsTxDTMFOption | 1.3.6.1.4.1.5003.9.10.3.1.3.12.21.1.5 | INTEGER | read-create | Transmit DTMF option. Access: Instant. AC INI-Param: N/A |
| INT enableCallWaitingPerPortAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.5 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT enableCallWaitingPerPortActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.6 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT enableCallWaitingPerPortEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.7 | INTEGER | read-write | Enable. Access: Instant. AC INI-Param: CallWaitingPerPort_IsEnabled |
| enableCallWaitingPerPortEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1 | not-accessible | table | |
| U32 enableCallWaitingPerPortIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.1 | Unsigned32 | read-only | . AC INI-Param: CallWaitingPerPort_Index |
| INT enableCallWaitingPerPortIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.2 | INTEGER | read-write | Is this index used. Access: Instant. AC INI-Param: CallWaitingPerPort_IsUsed |
| U32 enableCallWaitingPerPortModule | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.3 | Unsigned32 | read-only | module. AC INI-Param: CallWaitingPerPort_Module |
| U32 enableCallWaitingPerPortPort | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21.1.4 | Unsigned32 | read-only | port. AC INI-Param: CallWaitingPerPort_Port |
| enableCallWaitingPerPortTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.21 | not-accessible | ||
| INT enableDidPortAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT enableDidPortActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT enableDidPortEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.5 | INTEGER | read-write | Enable. Access: Instant. AC INI-Param: EnableDid_IsEnable |
| enableDidPortEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1 | not-accessible | ||
| U32 enableDidPortIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.1 | Unsigned32 | read-only | . AC INI-Param: EnableDid_Index |
| INT enableDidPortIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.2 | INTEGER | read-write | Is this index used. Access: Offline. AC INI-Param: EnableDid_IsUsed |
| U32 enableDidPortModule | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.6 | Unsigned32 | read-only | Channels Module. AC INI-Param: EnableDid_Module |
| U32 enableDidPortPort | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21.1.7 | Unsigned32 | read-only | Channels Port. AC INI-Param: EnableDid_Port |
| enableDidPortTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.16.21 | not-accessible | ||
| fastStart | 1.3.6.1.4.1.5003.9.10.3.1.3.10.5 | |||
| INT fastStartIsFastConnectUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.10.5.1 | INTEGER | read-write | Use H.323 Fast Start call setup procedure. Access: Instant. AC INI-Param: ISFASTCONNECTUSED |
| INT fastStartIsFSMediaInfoSendOnConnect | 1.3.6.1.4.1.5003.9.10.3.1.3.10.5.3 | INTEGER | read-write | Is Fast start Media sent in in Connect or in Alert. Access: Instant. AC INI-Param: ISFSMEDIAINFOSENDONCONNECT |
| INT fastStartIsFSOpenMediaOnConnect | 1.3.6.1.4.1.5003.9.10.3.1.3.10.5.4 | INTEGER | read-write | Open voice channel afer sending Connect or after sending Alert. Access: Instant. AC INI-Param: ISFSOPENMEDIAONCONNECT |
| U32 fastStartOpenH245OnFS | 1.3.6.1.4.1.5003.9.10.3.1.3.10.5.2 | Unsigned32 | read-write | Open H.245 when using Fast Start call setup procedure. Access: Instant. AC INI-Param: OPENH245ONFS |
| INT forwardAction | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT forwardActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| forwardEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1 | not-accessible | ||
| STR forwardForwardedToNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.6 | SnmpAdminString | read-write | Access: Instant. AC INI-Param: FwdInfo_Destination |
| INT forwardForwardType | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.5 | INTEGER | read-write | Access: Instant. AC INI-Param: FwdInfo_Type |
| U32 forwardIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.1 | Unsigned32 | read-only | Entry number, starting at 0. AC INI-Param: FwdInfo_Index |
| INT forwardIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.2 | INTEGER | read-write | Is this index used. AC INI-Param: FwdInfo_IsUsed |
| U32 forwardModule | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.8 | Unsigned32 | read-only | Module. AC INI-Param: FwdInfo_Module |
| INT forwardOnBusyTrunkDestAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT forwardOnBusyTrunkDestActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| forwardOnBusyTrunkDestEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1 | not-accessible | ||
| STR forwardOnBusyTrunkDestForwardDestination | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1.6 | SnmpAdminString | read-create | GwApp Forward On Busy Trunk Destination Table. Access: Instant. AC INI-Param: ForwardOnBusyTrunkDest_ForwardDestination |
| U32 forwardOnBusyTrunkDestIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: ForwardOnBusyTrunkDest_Index |
| ROW forwardOnBusyTrunkDestRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| forwardOnBusyTrunkDestTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5 | not-accessible | GwApp Forward On Busy Trunk Destination Table | |
| U32 forwardOnBusyTrunkDestTrunkGroupId | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.5.1.5 | Unsigned32 | read-create | GwApp Forward On Busy Trunk Destination Table. Access: Instant. AC INI-Param: ForwardOnBusyTrunkDest_TrunkGroupId |
| U32 forwardPort | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.9 | Unsigned32 | read-only | Port. AC INI-Param: FwdInfo_Port |
| forwardSettings | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12 | |||
| INT forwardSettingsEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.1 | INTEGER | read-write | Enable Call Forward service. Access: Instant. AC INI-Param: ENABLEFORWARD |
| forwardTable | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21 | not-accessible | ||
| U32 forwardTimeForNoReply | 1.3.6.1.4.1.5003.9.10.3.1.1.7.12.21.1.7 | Unsigned32 | read-write | Access: Instant. AC INI-Param: FwdInfo_NoReplyTime |
| fxo | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11 | |||
| INT fxoAutoDialPlayBusyTone | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.8 | INTEGER | read-write | Only for FXO, Tel2IP calls: If enable (1) - On receiving release, if autodial is used, the FXO seize the line and play Busy/Reorder tone toward the PSTN for Reorder-time duration. . Access: Instant. AC INI-Param: FXOAutoDialPlayBusyTone |
| U32 fxoBetweenRingTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.4 | Unsigned32 | read-write | Timeout for releasing FXO to IP call, if FXO port doesn't detect ringing signal for this timeout. Access: Instant. AC INI-Param: FXOBETWEENRINGTIME |
| INT fxoEnableVoiceDetection | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.5 | INTEGER | read-write | On FXO GWs enables sending of connect/200 OK message on speech/fax/modem detection [default 0]. In order to activate feature DSPVersionTemplateNumber should be 2 or 3. Access: Instant. AC INI-Param: ENABLEVOICEDETECTION |
| U32 fxoGuardTimeBetweenCalls | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.7 | Unsigned32 | read-write | Only for FXO: the time between the time that the EP execute OnHook, to the time that this EP is capable to except new IP2TEL call (and execute OfHook). Access: Instant. AC INI-Param: GUARDTIMEBETWEENCALLS |
| INT fxoIsTwoStageDial | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.1 | INTEGER | read-write | Dialing Mode - One-Stage (PBX Pass-thru) or Two-Stage. Access: Instant. AC INI-Param: ISTWOSTAGEDIAL |
| U32 fxoRingsBeforeCallerID | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.6 | Unsigned32 | read-write | Number of rings after which the Caller ID is detected. Access: Instant. AC INI-Param: RINGSBEFORECALLERID |
| U32 fxoWaitForDialTime | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.3 | Unsigned32 | read-write | Time delay between seizing the line and start dialing (if ISWAITFORDIALTONE disabled) or after hookflash before dialing. Access: Instant. AC INI-Param: WAITFORDIALTIME |
| INT fxoWaitForDialTone | 1.3.6.1.4.1.5003.9.10.3.1.1.4.11.2 | INTEGER | read-write | Wait for dial tone before initiating an outgoing call to PBX/PSTN (FXO one-stage dialing mode). Access: Instant. AC INI-Param: ISWAITFORDIALTONE |
| fxs | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10 | |||
| INT fxsCutThrough | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.1 | INTEGER | read-write | Enable call connection without On-Hook/Off-Hook process 'Cut-Through'. Access: Instant. AC INI-Param: CUTTHROUGH |
| INT fxsFXSOOSBehavior | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.3 | INTEGER | read-write | FxsOosBehavior control how the fxs endpoints of a gateway, will behave in case of Out of Service. OutofService state may be result of two scenarios: a. EndPoint not configured in trunkgroup (Disabled) b. runtime busy out situation 0: NONE - no special activity. Disabled endpoint not responses, bsyout endpoint responses as usual 1: Play ReOrder tone 2: Reverse Polarity 3: Play ReOrder tone and Reverse Polarity. Access: Instant. AC INI-Param: FXSOOSBEHAVIOR |
| INT fxsMeteringMode | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.2 | INTEGER | read-write | Method of automatic generation of payphone metering pulses. Access: Instant. AC INI-Param: PAYPHONEMETERINGMODE |
| INT fxsSetOOSOnRegistrationFail | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.4 | INTEGER | read-write | Should deactivate endpoint service on registration failure. Access: Instant. AC INI-Param: OOSONREGISTRATIONFAIL |
| INT gkIPAction | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT gkIPActionResult | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| gkIPEntry | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1 | not-accessible | ||
| STR gkIPGatekeeperIP | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1.5 | SnmpAdminString | read-create | IP of GK. Access: Offline. AC INI-Param: GateKeeperIp_IpAddress |
| STR gkIPGateleeperID | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1.6 | SnmpAdminString | read-create | ID of GK. Access: Offline. AC INI-Param: GateKeeperIp_Id |
| U32 gkIPIndex | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: GateKeeperIp_Index |
| ROW gkIPRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21.1.2 | RowStatus | read-create | This object allows entries to be created and deleted from the table. For Reference: RFC 1903, Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2). Access: Instant. AC INI-Param: N/A |
| gkIPTable | 1.3.6.1.4.1.5003.9.10.3.1.3.11.21 | not-accessible | ||
| gkRAI | 1.3.6.1.4.1.5003.9.10.3.1.3.11.31 | |||
| INT gkRAIEnable | 1.3.6.1.4.1.5003.9.10.3.1.3.11.31.1 | INTEGER | read-write | Enable sending of H.323 Resource Avaialable Indication message to Gatekeeper due to overload. Access: Instant. AC INI-Param: ENABLERAI |
| U32 gkRAIHighThreshold | 1.3.6.1.4.1.5003.9.10.3.1.3.11.31.2 | Unsigned32 | read-write | Percentage of active calls in order to send 'Almost out of resources' RAI. Access: Instant. AC INI-Param: RAIHIGHTHRESHOLD |
| U32 gkRAILoopTime | 1.3.6.1.4.1.5003.9.10.3.1.3.11.31.4 | Unsigned32 | read-write | Time period to check call resources (seconds). Access: Instant. AC INI-Param: RAILOOPTIME |
| U32 gkRAILowThreshold | 1.3.6.1.4.1.5003.9.10.3.1.3.11.31.3 | Unsigned32 | read-write | percentage of active calls to send 'Resources OK' RAI. Access: Instant. AC INI-Param: RAILOWTHRESHOLD |
| gkRedundancy | 1.3.6.1.4.1.5003.9.10.3.1.3.11.30 | |||
| U32 gkRedundancyTimeBetweenGKsLoops | 1.3.6.1.4.1.5003.9.10.3.1.3.11.30.2 | Unsigned32 | read-write | Time between the gateway retries to connect to Gatekeeper if connection was lost (seconds). Access: Instant. AC INI-Param: TIMEBETWEENGKSLOOPS |
| INT gkRedundancyUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.11.30.1 | INTEGER | read-write | Allow Gatekeeper redundancy. At least one redundant Gatekeeper should be defined. Access: Instant. AC INI-Param: ISREDUNDANTGKUSED |
| gwConfiguration | 1.3.6.1.4.1.5003.9.10.3.1 | |||
| gwIPv6 | 1.3.6.1.4.1.5003.9.10.3.1.1.25 | |||
| INT gwIPv6GwAppDualIPStackSDPMethod | 1.3.6.1.4.1.5003.9.10.3.1.1.25.1 | INTEGER | read-write | 0. Always offer a single (preferrable) media IP address. 1. ANAT - Construct offer using ANAT semantics (RFC 4091 & RFC 4092) . Access: Instant. AC INI-Param: DUALIPSTACKSDPMETHOD |
| I32 gwIPv6GwAppPrimaryMediaInterface | 1.3.6.1.4.1.5003.9.10.3.1.1.25.2 | Integer32 | read-write | Primary media interface to be used within SDP. Access: Instant. AC INI-Param: PRIMARYMEDIAINTERFACE |
| I32 gwIPv6GwAppSecondaryMediaInterface | 1.3.6.1.4.1.5003.9.10.3.1.1.25.3 | Integer32 | read-write | Secondary media interface to be used within SDP. Access: Instant. AC INI-Param: SECONDARYMEDIAINTERFACE |
| INT gwIPv6MediaIPVersionPreference | 1.3.6.1.4.1.5003.9.10.3.1.1.25.4 | INTEGER | read-write | Select the preferred Media IP version. Access: Instant. AC INI-Param: MEDIAIPVERSIONPREFERENCE |
| gwSecurity | 1.3.6.1.4.1.5003.9.10.3.1.1.18 | |||
| INT gwSecurityMediaSecurityBehavior | 1.3.6.1.4.1.5003.9.10.3.1.1.18.1 | INTEGER | read-write | Gateway behavior when recieving offer/response for media encryption. Access: Instant. AC INI-Param: MEDIASECURITYBEHAVIOUR |
| INT gwSecurityPeerHostNameVerificationMode | 1.3.6.1.4.1.5003.9.10.3.1.1.18.4 | INTEGER | read-write | While using TLS, defines the verification behavior of the host name sent in the certificate. Access: Instant. AC INI-Param: PEERHOSTNAMEVERIFICATIONMODE |
| INT gwSecuritySIPSRequireClientCertificate | 1.3.6.1.4.1.5003.9.10.3.1.1.18.2 | INTEGER | read-write | Should require client certificate upon TLS connection request arrival. Access: Offline. AC INI-Param: SIPSREQUIRECLIENTCERTIFICATE |
| INT gwSecuritySRTPofferedSuites | 1.3.6.1.4.1.5003.9.10.3.1.1.18.7 | INTEGER | read-write | Offered SRTP Cipher Suites. Access: Instant. AC INI-Param: SRTPOFFEREDSUITES |
| U32 gwSecurityTLSReHandshakeInterval | 1.3.6.1.4.1.5003.9.10.3.1.1.18.3 | Unsigned32 | read-write | The interval between consequent TLS re-handshakes (Minutes). 0 - Disables re-handshakes. Access: Instant. AC INI-Param: TLSREHANDSHAKEINTERVAL |
| STR gwSecurityTLSRemoteSubjectName | 1.3.6.1.4.1.5003.9.10.3.1.1.18.6 | SnmpAdminString | read-write | used to verify the remote peer Common Name (at certificate) when using TLS. Access: Instant. AC INI-Param: TLSREMOTESUBJECTNAME |
| INT gwSecurityVerifyServerCertificate | 1.3.6.1.4.1.5003.9.10.3.1.1.18.5 | INTEGER | read-write | Certificate validation behavior 0 � No certificate validation. 1 � Server certificate validation. Access: Instant. AC INI-Param: VERIFYSERVERCERTIFICATE |
| h323 | 1.3.6.1.4.1.5003.9.10.3.1.3 | |||
| h323Auth | 1.3.6.1.4.1.5003.9.10.3.1.3.14 | |||
| INT h323AuthEnableH235Security | 1.3.6.1.4.1.5003.9.10.3.1.3.14.1 | INTEGER | read-write | Enable H.235 security. Access: Offline. AC INI-Param: ENABLEH235SECURITY |
| STR h323AuthPassword | 1.3.6.1.4.1.5003.9.10.3.1.3.14.3 | SnmpAdminString | read-write | Password used for authentication. Access: Instant. AC INI-Param: PASSWORD |
| STR h323AuthUserName | 1.3.6.1.4.1.5003.9.10.3.1.3.14.2 | SnmpAdminString | read-write | User Name used for authentication. Access: Instant. AC INI-Param: USERNAME |
| h323ConnectionModes | 1.3.6.1.4.1.5003.9.10.3.1.3.10 | |||
| INT h323ConnectionModesIsTunnelingUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.10.1 | INTEGER | read-write | Use H.323 Tunneling call setup procedure. Access: Instant. AC INI-Param: ISTUNNELINGUSED |
| INT h323DestEncodType | 1.3.6.1.4.1.5003.9.10.3.1.3.2 | INTEGER | read-write | Called number coding type in Setup message. Access: Instant. AC INI-Param: DESTENCODTYPE |
| h323DTMF | 1.3.6.1.4.1.5003.9.10.3.1.3.12 | |||
| INT h323DTMFHookFlashOption | 1.3.6.1.4.1.5003.9.10.3.1.3.12.1 | INTEGER | read-write | Detect and send Hook-Flash using the selected method. Access: Instant. AC INI-Param: HOOKFLASHOPTION |
| INT h323DTMFRxDtmfOption | 1.3.6.1.4.1.5003.9.10.3.1.3.12.2 | INTEGER | read-write | Declare support for RFC 2833 in SDP. Access: Instant. AC INI-Param: ISFALLBACKUSED |
| h323GK | 1.3.6.1.4.1.5003.9.10.3.1.3.11 | |||
| INT h323GKAlternativeGKUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.11.12 | INTEGER | read-write | Allows working with Alternative GK that should be provided by GK. Access: Offline. AC INI-Param: ALTERNATIVEGKUSED |
| INT h323GKCanMapAliases | 1.3.6.1.4.1.5003.9.10.3.1.3.11.4 | INTEGER | read-write | If enabled, Gatekeeper can change gateway destination number using the Alias parameter in ACF message. Access: Instant. AC INI-Param: CANMAPALIASES |
| INT h323GKEnableGKAutoDiscovery | 1.3.6.1.4.1.5003.9.10.3.1.3.11.14 | INTEGER | read-write | Enables GK automatic discovery mechanism. Access: Offline. AC INI-Param: ENABLEGKAUTODISCOVERY |
| INT h323GKEnablePregrantARQ | 1.3.6.1.4.1.5003.9.10.3.1.3.11.10 | INTEGER | read-write | ARQ message won't be sent if the Gatekeeper has pre-granted admission. Access: Instant. AC INI-Param: ENABLEPREGRANTARQ |
| STR h323GKGatekeeperID | 1.3.6.1.4.1.5003.9.10.3.1.3.11.9 | SnmpAdminString | read-write | Gatekeeper Identification name, to be used in Registration Request (RRQ) messages. Access: Instant. AC INI-Param: GATEKEEPERID |
| IP h323GKGKAutoDiscoveryIP | 1.3.6.1.4.1.5003.9.10.3.1.3.11.15 | IpAddress | read-write | Multicast IP Address for GK automatic discovery. Access: Offline. AC INI-Param: GKAUTODISCOVERYIP |
| INT h323GKGwRegistrType | 1.3.6.1.4.1.5003.9.10.3.1.3.11.2 | INTEGER | read-write | Type of Gatekeeper registration. Access: Instant. AC INI-Param: GWREGISTRTYPE |
| INT h323GKIsGateKeeperUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.11.1 | INTEGER | read-write | Is gateway using a H.323 Gatekeeper. Access: Offline. AC INI-Param: ISGATEKEEPERUSED |
| INT h323GKIsGkFallbackUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.11.3 | INTEGER | read-write | Allow fallback to internal Tel to IP routing table if Gatekeeper/Proxy is not responding. Access: Offline. AC INI-Param: ISFALLBACKUSED |
| INT h323GKIsTerminal | 1.3.6.1.4.1.5003.9.10.3.1.3.11.8 | INTEGER | read-write | The gateway registers as a H.323 terminal with multiple aliases. Otherwise, the gateway behaves as an H.323 gateway. Access: Instant. AC INI-Param: ISTERMINAL |
| U32 h323GKMaxRetries | 1.3.6.1.4.1.5003.9.10.3.1.3.11.6 | Unsigned32 | read-write | Maximum number of retransmissions of RAS messages to Gatekeeper. Access: Instant. AC INI-Param: MAXRETRIES |
| INT h323GKRegister | 1.3.6.1.4.1.5003.9.10.3.1.3.11.11 | INTEGER | read-write | This parameter related to Register/UnRegister buttons. Access: Instant. AC INI-Param: SHOULDREGISTER |
| U32 h323GKRegistrationTime | 1.3.6.1.4.1.5003.9.10.3.1.3.11.7 | Unsigned32 | read-write | Time in seconds for which registration to Gatekeeper/Proxy is valid. cause periodic registration. Access: Offline. AC INI-Param: REGISTRATIONTIME |
| U32 h323GKResponseTimeout | 1.3.6.1.4.1.5003.9.10.3.1.3.11.5 | Unsigned32 | read-write | Time in which the gateway waits for a RAS response from the Gatekeeper before retransmission (seconds). Access: Instant. AC INI-Param: RESPONSETIMEOUT |
| INT h323GKUseRedundantGKOnRRJ | 1.3.6.1.4.1.5003.9.10.3.1.3.11.13 | INTEGER | read-write | Useredundant Gatekeeper on receiving RRJ message. Access: Offline. AC INI-Param: USEREDUNDANTGKONRRJ |
| STR h323H323IDString | 1.3.6.1.4.1.5003.9.10.3.1.3.3 | SnmpAdminString | read-write | Definition of Gateway H.323-ID source field. Access: Instant. AC INI-Param: H323IDSTRING |
| h323Misc | 1.3.6.1.4.1.5003.9.10.3.1.3.15 | |||
| INT h323MiscEnableQ931Cause | 1.3.6.1.4.1.5003.9.10.3.1.3.15.4 | INTEGER | read-write | H.225 Reason / Q.931 Cause is sent in H.323 Release Complete message. Access: Instant. AC INI-Param: ENABLEQ931CAUSE |
| INT h323MiscEnableQ931Multiplexing | 1.3.6.1.4.1.5003.9.10.3.1.3.15.5 | INTEGER | read-write | Use same socket for all H.225 messages. Access: Instant. AC INI-Param: ENABLEQ931MULTIPLEXING |
| U32 h323MiscH245InitTimeOut | 1.3.6.1.4.1.5003.9.10.3.1.3.15.3 | Unsigned32 | read-write | h245.channelsTimeout value. Access: Offline. AC INI-Param: H245INITTIMEOUT |
| U32 h323MiscH245RoundTripTime | 1.3.6.1.4.1.5003.9.10.3.1.3.15.7 | Unsigned32 | read-write | Time between H.245 Round Trip Delay messages (seconds). Access: Instant. AC INI-Param: H245ROUNDTRIPTIME |
| INT h323MiscIsSetupAckUsed | 1.3.6.1.4.1.5003.9.10.3.1.3.15.2 | INTEGER | read-write | Enable SetupAck messages for overlap mode. Access: Instant. AC INI-Param: ISSETUPACKUSED |
| INT h323MiscIsSetupIncludeNum | 1.3.6.1.4.1.5003.9.10.3.1.3.15.1 | INTEGER | read-write | Setup message contains called party number. Access: Instant. AC INI-Param: ISSETUPINCLUDENUM |
| INT h323MiscProgressBehavior | 1.3.6.1.4.1.5003.9.10.3.1.3.15.8 | INTEGER | read-write | Interworking behavior of Progress message (0-Alert, 1-Progress). Access: Instant. AC INI-Param: H323PROGRESSBEHAVIOR |
| INT h323MiscSendChannelNonStandard | 1.3.6.1.4.1.5003.9.10.3.1.3.15.6 | INTEGER | read-write | Send trunk and bchannel numbers on setup and call proceeding messages as nonStandard data. Access: Instant. AC INI-Param: SENDCHANNELNONSTANDARD |
| h323Ports | 1.3.6.1.4.1.5003.9.10.3.1.3.13 | |||
| U32 h323PortsH225DialPort | 1.3.6.1.4.1.5003.9.10.3.1.3.13.2 | Unsigned32 | read-write | Port on which the gateway sends H.225 Setup messages. (Usually 1720). Access: Offline. AC INI-Param: H225DIALPORT |
| U32 h323PortsH225ListenPort | 1.3.6.1.4.1.5003.9.10.3.1.3.13.1 | Unsigned32 | read-write | Port on which the gateway expects to receive H.225 Setup messages. (Usually 1720). Access: Offline. AC INI-Param: H225LISTENPORT |
| U32 h323PortsH323BasePort | 1.3.6.1.4.1.5003.9.10.3.1.3.13.3 | Unsigned32 | read-write | Defines range for gateway H.225/H.245 local port messages. Access: Offline. AC INI-Param: H323BASEPORT |
| U32 h323PortsRasDestPort | 1.3.6.1.4.1.5003.9.10.3.1.3.13.5 | Unsigned32 | read-write | RAS requests destination port. Access: Instant. AC INI-Param: RASDESTPORT |
| U32 h323PortsRasSourcePort | 1.3.6.1.4.1.5003.9.10.3.1.3.13.4 | Unsigned32 | read-write | RAS requests source port. Access: Instant. AC INI-Param: RASSOURCEPORT |
| INT h323SourceEncodType | 1.3.6.1.4.1.5003.9.10.3.1.3.1 | INTEGER | read-write | Calling number coding type in Setup message. Access: Instant. AC INI-Param: SOURCEENCODTYPE |
| iE | 1.3.6.1.4.1.5003.9.10.3.1.1.3.20 | |||
| STR iEAddIEInSetup | 1.3.6.1.4.1.5003.9.10.3.1.1.3.20.1 | SnmpAdminString | read-write | Additional information element to send in ISDN Setup message. Access: Instant. AC INI-Param: ADDIEINSETUP |
| STR iESendIEOnTG | 1.3.6.1.4.1.5003.9.10.3.1.1.3.20.2 | SnmpAdminString | read-write | Configure trunk groups on which to send additional IE. Access: Instant. AC INI-Param: SENDIEONTG |
| INT iP2TelRoutingAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT iP2TelRoutingActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR iP2TelRoutingAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.8 | SnmpAdminString | read-create | Address (IP or DNS name). Access: Instant. AC INI-Param: PstnPrefix_SourceAddress |
| STR iP2TelRoutingDestHostPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.11 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: PstnPrefix_DestHostPrefix |
| iP2TelRoutingEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1 | not-accessible | ||
| U32 iP2TelRoutingIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: PstnPrefix_Index |
| STR iP2TelRoutingPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.5 | SnmpAdminString | read-create | Phone number prefix. up to 80 digits. can be used for defining range of phone numbers. Access: Instant. AC INI-Param: PstnPrefix_DestPrefix |
| U32 iP2TelRoutingProfileID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.9 | Unsigned32 | read-create | Profile ID. Access: Instant. AC INI-Param: PstnPrefix_ProfileId |
| ROW iP2TelRoutingRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| STR iP2TelRoutingSourceHostPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.12 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: PstnPrefix_SrcHostPrefix |
| I32 iP2TelRoutingSourceIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.10 | Integer32 | read-create | Access: Instant. AC INI-Param: PstnPrefix_SrcIPGroupID |
| STR iP2TelRoutingSrcPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.7 | SnmpAdminString | read-create | Calling Phone number prefix. up to 49 digits. can be used for defining range of phone numbers. Access: Instant. AC INI-Param: PstnPrefix_SourcePrefix |
| iP2TelRoutingTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2 | not-accessible | Phone prefix to Trunk group (or Hunt Group for MP-1xx)routing table. The table is used for routing outgoing IP Telco calls, according to received from IP destination phone number. | |
| U32 iP2TelRoutingTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.2.1.6 | Unsigned32 | read-create | Trunk/Hunt group ID. Access: Instant. AC INI-Param: PstnPrefix_TrunkGroupId |
| INT ipGroupAction | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT ipGroupActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT ipGroupAlwaysUseRouteTable | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.13 | INTEGER | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_AlwaysUseRouteTable |
| STR ipGroupContactUser | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.9 | SnmpAdminString | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_ContactUser |
| STR ipGroupDescription | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.6 | SnmpAdminString | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_Description |
| INT ipGroupEnableSurvivability | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.10 | INTEGER | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_EnableSurvivability |
| ipGroupEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1 | not-accessible | table | |
| U32 ipGroupIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.1 | Unsigned32 | read-only | . AC INI-Param: IPGroup_Index |
| I32 ipGroupMaxNumOfRegUsers | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.17 | Integer32 | read-create | Max Number Of Registered Users. MP1xx - 25 M1K - 200 M2K- 250 M3K - 3000. Access: Offline. AC INI-Param: IPGroup_MaxNumOfRegUsers |
| STR ipGroupMediaRealm | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.16 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPGroup_MediaRealm |
| U32 ipGroupProfileId | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.15 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPGroup_ProfileId |
| I32 ipGroupProxySetId | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.7 | Integer32 | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_ProxySetId |
| INT ipGroupRoutingMode | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.14 | INTEGER | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_RoutingMode |
| ROW ipGroupRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| ipGroups | 1.3.6.1.4.1.5003.9.10.3.1.1.23 | |||
| I32 ipGroupServingIPGroup | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.11 | Integer32 | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_ServingIPGroup |
| STR ipGroupSIPGroupName | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.8 | SnmpAdminString | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_SIPGroupName |
| INT ipGroupSipReRoutingMode | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.12 | INTEGER | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_SipReRoutingMode |
| ipGroupTable | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21 | not-accessible | GwApp IP Group Table | |
| INT ipGroupType | 1.3.6.1.4.1.5003.9.10.3.1.1.23.21.1.5 | INTEGER | read-create | GwApp IP Group Table. Access: Instant. AC INI-Param: IPGroup_Type |
| INT iPProfileAction | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT iPProfileActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR iPProfileAddIEInSetup | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.28 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IpProfile_AddIEInSetup |
| I32 iPProfileCallLimit | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.25 | Integer32 | read-create | Access: Instant. AC INI-Param: IpProfile_CallLimit |
| INT iPProfileCngDetectorMode | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.17 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_CNGmode |
| U32 iPProfileCodersGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.7 | Unsigned32 | read-create | Coders Group ID. Access: Instant. AC INI-Param: IpProfile_CodersGroupID |
| INT iPProfileCopyDest2RedirectNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.27 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_CopyDest2RedirectNumber |
| INT iPProfileDisconnectOnBrokenConnection | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.26 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_DisconnectOnBrokenConnection |
| U32 iPProfileDJBufMinDelay | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.10 | Unsigned32 | read-create | Dynamic Jitter Buffer Minimum Delay (msec). Access: Instant. AC INI-Param: IpProfile_JitterBufMinDelay |
| U32 iPProfileDJBufOptFactor | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.11 | Unsigned32 | read-create | Dynamic jitter buffer frame error/delay optimization. Access: Instant. AC INI-Param: IpProfile_JitterBufOptFactor |
| INT iPProfileECE | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.23 | INTEGER | read-create | Enables or disables the echo canceler. Access: Instant. AC INI-Param: IpProfile_EnableEchoCanceller |
| INT iPProfileEnableEarlyMedia | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.21 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_EnableEarlyMedia |
| iPProfileEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1 | not-accessible | ||
| U32 iPProfileFaxTransportMode | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.8 | Unsigned32 | read-write | Fax Transport Mode. Access: Instant. AC INI-Param: N/A |
| INT iPProfileFirstTxDtmfOption | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.30 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_FirstTxDtmfOption |
| U32 iPProfileIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.1 | Unsigned32 | not-accessible | Entry number, starting at 1. AC INI-Param: IpProfile_Index |
| U32 iPProfileIPDiffServ | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.12 | Unsigned32 | read-create | IP DiffServ byte value. Access: Instant. AC INI-Param: IpProfile_IPDiffServ |
| INT iPProfileIsFaxUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.9 | INTEGER | read-create | Use H.323/Annex D procedure for real time FAX relay. To use this feature, disable inband DTMF by setting the FaxTransportMode to 1. Access: Instant. AC INI-Param: IpProfile_IsFaxUsed |
| INT iPProfileMediaIPVersionPreference | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.32 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_MediaIPVersionPreference |
| INT iPProfileMediaSecurityBehavior | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.24 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_MediaSecurityBehaviour |
| INT iPProfileNSEMode | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.19 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_NSEMode |
| INT iPProfilePlayRingbackToneToIP | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.20 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_PlayRBTone2IP |
| U32 iPProfilePreference | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.5 | Unsigned32 | read-create | Preference. Access: Instant. AC INI-Param: IpProfile_IpPreference |
| STR iPProfileProfileName | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.6 | SnmpAdminString | read-create | Profile Name. Access: Instant. AC INI-Param: IpProfile_ProfileName |
| INT iPProfileProgressIndicatorToIP | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.22 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_ProgressIndicator2IP |
| U32 iPProfileRemoteBaseUDPPort | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.16 | Unsigned32 | read-create | Remote Base UDP Port For Aggregation. Access: Instant. AC INI-Param: IpProfile_RemoteBaseUDPPort |
| ROW iPProfileRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| U32 iPProfileRTPRedundancyDepth | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.15 | Unsigned32 | read-create | Enables or disables generation of RFC 2198 redundancy packets. Access: Instant. AC INI-Param: IpProfile_RTPRedundancyDepth |
| INT iPProfileRxDTMFOption | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.29 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_RxDTMFOption |
| INT iPProfileSBCAllowedCodersGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.33 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_SBCAllowedCodersGroupID |
| INT iPProfileSBCAllowedCodersMode | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.34 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_SBCAllowedCodersMode |
| INT iPProfileSBCMediaSecurityBehaviour | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.35 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_SBCMediaSecurityBehaviour |
| INT iPProfileSCE | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.14 | INTEGER | read-create | Silence Suppression mode. Access: Instant. AC INI-Param: IpProfile_SCE |
| INT iPProfileSecondTxDtmfOption | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.31 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_SecondTxDtmfOption |
| U32 iPProfileSigIPDiffServ | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.13 | Unsigned32 | read-create | Type Of Service bits in IP header of signalling messages. Access: Instant. AC INI-Param: IpProfile_SigIPDiffServ |
| iPProfileTable | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21 | not-accessible | ||
| INT iPProfileVxxModemTransportType | 1.3.6.1.4.1.5003.9.10.3.1.1.15.21.1.18 | INTEGER | read-create | Access: Instant. AC INI-Param: IpProfile_VxxTransportType |
| INT iSDNRxOverlapEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.21.1.2 | INTEGER | read-write | Receive overlap from ISDN side. Access: Instant. AC INI-Param: ISDNRXOVERLAP |
| iSDNRxOverlapEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.21.1 | not-accessible | ||
| U32 iSDNRxOverlapIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.21.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| iSDNRxOverlapTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.21 | not-accessible | Choose either: Disabled or Enabled (default). Any number bigger than one = Number of digits to receive. Note 1: If enabled, the Mediant 2000 receives ISDN called number that is sent in the 'Overlap' mode. Note 2: The SETUP to IP is sent only after the number (including 'Sending Complete' Info Element) was fully received (via SETUP and/or subsequent INFO Q.931 messages). | |
| iSDNTransferCapabilityEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.25.1 | not-accessible | ||
| U32 iSDNTransferCapabilityIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.25.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| iSDNTransferCapabilityTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.25 | not-accessible | ISDN Transfer Capability Trunk table. | |
| INT iSDNTransferCapabilityValue | 1.3.6.1.4.1.5003.9.10.3.1.1.3.25.1.2 | INTEGER | read-write | Send transfer capability to ISDN side on setup message -1:Do not Overwrite 0:Audio 3.1 1:Speech 2:Data 3:Audio. Access: Instant. AC INI-Param: ISDNTRANSFERCAPABILITY |
| keypadFeatures | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14 | |||
| STR keypadFeaturesBlindTransfer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.11 | SnmpAdminString | read-write | Keying sequence for performing blind transfer. Access: Instant. AC INI-Param: KEYBLINDTRANSFER |
| STR keypadFeaturesCFBusy | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.4 | SnmpAdminString | read-write | Keying sequence for activating Call Forward on busy. Access: Instant. AC INI-Param: KEYCFBUSY |
| STR keypadFeaturesCFBusyOrNoAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.9 | SnmpAdminString | read-write | Keying sequence for activating Call Forward on busy or no answer. Access: Instant. AC INI-Param: KEYCFBUSYORNOANSWER |
| STR keypadFeaturesCFDeact | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.2 | SnmpAdminString | read-write | Keying sequence for deactivating Call Forward. Access: Instant. AC INI-Param: KEYCFDEACT |
| STR keypadFeaturesCFDoNotDisturb | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.10 | SnmpAdminString | read-write | Keying sequence for activating Do Not Disturb. Access: Instant. AC INI-Param: KEYCFDONOTDISTURB |
| STR keypadFeaturesCFNoAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.3 | SnmpAdminString | read-write | Keying sequence for activating Call Forward on no answer. Access: Instant. AC INI-Param: KEYCFNOANSWER |
| STR keypadFeaturesCFUncond | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.1 | SnmpAdminString | read-write | Keying sequence for activating immediate Call Forward. Access: Instant. AC INI-Param: KEYCFUNCOND |
| STR keypadFeaturesCLIR | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.5 | SnmpAdminString | read-write | Keying sequence for activating restricted Caller ID. Access: Instant. AC INI-Param: KEYCLIR |
| STR keypadFeaturesCLIRDeact | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.6 | SnmpAdminString | read-write | Keying sequence for deactivating restricted Caller ID. Access: Instant. AC INI-Param: KEYCLIRDEACT |
| STR keypadFeaturesHotLine | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.7 | SnmpAdminString | read-write | Keying sequence for activating delayed Hot-line. Access: Instant. AC INI-Param: KEYHOTLINE |
| STR keypadFeaturesHotLineDeact | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.8 | SnmpAdminString | read-write | Keying sequence for deactivating delayed Hot-line. Access: Instant. AC INI-Param: KEYHOTLINEDEACT |
| STR keypadFeaturesKeypadFeaturesCW | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.12 | SnmpAdminString | read-write | Keying sequence for activating call waiting. Access: Instant. AC INI-Param: KEYCALLWAITINGDEACT |
| STR keypadFeaturesKeypadFeaturesCWDeact | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.13 | SnmpAdminString | read-write | Keying sequence for deactivating call waiting. Access: Instant. AC INI-Param: KEYCALLWAITINGDEACT |
| STR keypadFeaturesRejectAnonymousCall | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.14 | SnmpAdminString | read-write | Key pad pattern for rejecting anonymous call. Access: Instant. AC INI-Param: KeyRejectAnonymousCall |
| STR keypadFeaturesRejectAnonymousCallDeact | 1.3.6.1.4.1.5003.9.10.3.1.1.4.14.15 | SnmpAdminString | read-write | Key pad pattern for accepting anonymous call. Access: Instant. AC INI-Param: KeyRejectAnonymousCallDeact |
| localISDNRBSourceEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.26.1 | not-accessible | ||
| U32 localISDNRBSourceIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.26.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| localISDNRBSourceTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.26 | not-accessible | Play RB Tone To Trunk table. | |
| INT localISDNRBSourceValue | 1.3.6.1.4.1.5003.9.10.3.1.1.3.26.1.2 | INTEGER | read-write | If the ringback tone source is not IP, who should supply the Ringback tone. 0 - PBX/PSTN (default) ; 1- GW. Access: Instant. AC INI-Param: LOCALISDNRBSOURCE |
| logger | 1.3.6.1.4.1.5003.9.10.3.1.1.9 | |||
| IP loggerCDRSyslogServerIP | 1.3.6.1.4.1.5003.9.10.3.1.1.9.3 | IpAddress | read-write | Syslog server IP address for sending CDRs. Access: Instant. AC INI-Param: CDRSYSLOGSERVERIP |
| INT loggerGwAppCdrReportLevel | 1.3.6.1.4.1.5003.9.10.3.1.1.9.1 | INTEGER | read-write | CDR reports timing. Access: Instant. AC INI-Param: N/A |
| INT loggerGwDebugLevel | 1.3.6.1.4.1.5003.9.10.3.1.1.9.2 | INTEGER | read-write | Configure different debug level. Access: Instant. AC INI-Param: N/A |
| manipulation | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21 | |||
| INT manipulationAddNPIandTON2CalledNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.7 | INTEGER | read-write | Add NPI and TON as prefix to called number. Access: Instant. AC INI-Param: ADDNPIANDTON2CALLEDNUMBER |
| INT manipulationAddNPIandTON2CallingNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.8 | INTEGER | read-write | Add NPI and TON as prefix to calling number. Access: Instant. AC INI-Param: ADDNPIANDTON2CALLINGNUMBER |
| INT manipulationAddPhoneContextAsPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.11 | INTEGER | read-write | add the phone context to src/dest phone number as prefix. Access: Instant. AC INI-Param: ADDPHONECONTEXTASPREFIX |
| INT manipulationAddPortAsPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.3 | INTEGER | read-write | Add port number (Analog gateway) / Trunk ID (Digital gateway) as called number prefix. Access: Instant. AC INI-Param: ADDPORTASPREFIX |
| STR manipulationAddPrefixToRedirectNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.10 | SnmpAdminString | read-write | Prefix which added to redirect phone number. Access: Instant. AC INI-Param: PREFIX2REDIRECTNUMBER |
| INT manipulationAddTrunkGroupAsPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.2 | INTEGER | read-write | Add Trunk Group ID on which the call was received as the called number prefix. Access: Instant. AC INI-Param: ADDTRUNKGROUPASPREFIX |
| INT manipulationAddTrunkGroupAsPrefixToSource | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.14 | INTEGER | read-write | Add Trunk Group ID on which the call was received as the calling number prefix. Access: Instant. AC INI-Param: ADDTRUNKGROUPASPREFIXTOSOURCE |
| manipulationAndRouting | 1.3.6.1.4.1.5003.9.10.3.1.1.2 | |||
| INT manipulationAndRoutingAltRoutingTel2IpConnMethod | 1.3.6.1.4.1.5003.9.10.3.1.1.2.9 | INTEGER | read-write | Tel to IP Alternative Routing Connectivity Method. Access: Instant. AC INI-Param: ALTROUTINGTEL2IPCONNMETHOD |
| INT manipulationAndRoutingAltRoutingTel2IpEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.4 | INTEGER | read-write | Enable Tel to IP Alternative Routing. Can be enabled for status only without affecting routing. Access: Instant. AC INI-Param: ALTROUTINGTEL2IPENABLE |
| U32 manipulationAndRoutingAltRoutingTel2IpKeepAliveTime | 1.3.6.1.4.1.5003.9.10.3.1.1.2.12 | Unsigned32 | read-write | Time interval between OPTIONS Keep-Alive messages for IP connectivity (seconds). Access: Instant. AC INI-Param: ALTROUTINGTEL2IPKEEPALIVETIME |
| INT manipulationAndRoutingAltRoutingTel2IpMode | 1.3.6.1.4.1.5003.9.10.3.1.1.2.5 | INTEGER | read-write | Methods used for Alternative Routing operation. Access: Instant. AC INI-Param: ALTROUTINGTEL2IPMODE |
| U32 manipulationAndRoutingAltRoutingTel2IpQosAllowTheNCall | 1.3.6.1.4.1.5003.9.10.3.1.1.2.6 | Unsigned32 | read-write | in case of QOS problem, a call has this probability (in percents) to continue, in order to reevaluate the QOS. Access: Instant. AC INI-Param: ALTROUTINGTEL2IPQOSALLOWPROB |
| U32 manipulationAndRoutingAltRoutingToneDuration | 1.3.6.1.4.1.5003.9.10.3.1.1.2.11 | Unsigned32 | read-write | Alternative Routing Tone Duration. 0 - disabled (milliseconds). Access: Instant. AC INI-Param: ALTROUTINGTONEDURATION |
| INT manipulationAndRoutingFilterCalls2Ip | 1.3.6.1.4.1.5003.9.10.3.1.1.2.3 | INTEGER | read-write | When Gatekeeper/Proxy is enabled, do not start session if called number is not listed or restricted in Tel to IP routing table. Access: Instant. AC INI-Param: FILTERCALLS2IP |
| INT manipulationAndRoutingModeIp2Tel | 1.3.6.1.4.1.5003.9.10.3.1.1.2.2 | INTEGER | read-write | Defines order between routing incoming calls from IP side and performing manipulations. Access: Instant. AC INI-Param: ROUTEMODEIP2TEL |
| INT manipulationAndRoutingModeTel2Ip | 1.3.6.1.4.1.5003.9.10.3.1.1.2.1 | INTEGER | read-write | Defines order between routing incoming calls from Tel side and performing manipulations. Access: Instant. AC INI-Param: ROUTEMODETEL2IP |
| INT manipulationAndRoutingPreferRouteTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.7 | INTEGER | read-write | Prefer Routing Table. Access: Instant. AC INI-Param: PREFERROUTETABLE |
| INT manipulationAndRoutingRedundantRoutingMode | 1.3.6.1.4.1.5003.9.10.3.1.1.2.8 | INTEGER | read-write | Mode of redundant routing. 0 - Disabled, 1 - Use routing table, 2 - Use proxies list. Access: Instant. AC INI-Param: REDUNDANTROUTINGMODE |
| INT manipulationAndRoutingSIPReRoutingMode | 1.3.6.1.4.1.5003.9.10.3.1.1.2.10 | INTEGER | read-write | Defines the routing mode after receiving 3xx response or transfer 0 - standard mode 1 - send invite to proxy 2 - use routing table. Access: Instant. AC INI-Param: SIPREROUTINGMODE |
| INT manipulationBlindTransferAddPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.12 | INTEGER | read-write | Add keying sequence for performing blind transfer as transfer number prefix. Access: Instant. AC INI-Param: KEYBLINDTRANSFERADDPREFIX |
| INT manipulationCIDNotification | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.5 | INTEGER | read-write | If NO PRESENTATION arrived from PSTN and this parameter enabled,than the presentation will be allowed. If this parameter disabled, the, presentation will be restricted. Access: Instant. AC INI-Param: CIDNOTIFICATION |
| INT manipulationRemovePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.1 | INTEGER | read-write | Remove prefix defined in IP to Trunk Group table (IP to Tel calls). Access: Instant. AC INI-Param: REMOVEPREFIX |
| INT manipulationReplaceEmptyDstWithPortNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.4 | INTEGER | read-write | Replace empty destination number (received from Tel side) with port number. Access: Instant. AC INI-Param: REPLACEEMPTYDSTWITHPORTNUMBER |
| INT manipulationSetIp2TelRedirectReason | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.16 | INTEGER | read-write | If redirect (diversion) data is received from the IP side, the redirect reason is set to the value of this parameter, before transferring it to the PSTN interface. default value is -1 --> not change the received value. . Access: Instant. AC INI-Param: SetIp2TelRedirectReason |
| INT manipulationSetIp2TelRedirectScreeningIndicator | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.17 | INTEGER | read-write | Override screening indicator value of the redirect number in Setup messages to PSTN interface. Access: Instant. AC INI-Param: SetIp2TelRedirectScreeningInd |
| INT manipulationSetTel2IpRedirectReason | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.15 | INTEGER | read-write | If redirect (diversion) data is received from the PSTN interface, the redirect reason is set to the value of this parameter, before transferring it to the IP. default value is -1 --> not change the received value. . Access: Instant. AC INI-Param: SetTel2IpRedirectReason |
| INT manipulationSourceMode | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.13 | INTEGER | read-write | Describes the headers containing source number after manipulation: (0) both FROM and P-Asserted contain src number after manipulations (1) only FROM contains src number after manipulation. Access: Instant. AC INI-Param: SOURCEMANIPULATIONMODE |
| INT manipulationUseDisplayNameAsSourceNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.9 | INTEGER | read-write | when set to 1 then If display name exists, use it as source number. If not, set presentation as restricted. Access: Instant. AC INI-Param: USEDISPLAYNAMEASSOURCENUMBER |
| INT manipulationUseSourceNumberAsDisplayName | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.6 | INTEGER | read-write | if set to 1 Use source number as display name if empty. if set to 2 always use source number as display name . Access: Instant. AC INI-Param: USESOURCENUMBERASDISPLAYNAME |
| mediaGW | 1.3.6.1.4.1.5003.9.10.3.1.1.5 | |||
| U32 mediaGWMediaChannels | 1.3.6.1.4.1.5003.9.10.3.1.1.5.1 | Unsigned32 | read-write | Number of channels associated with media services (announcements, conferencing). Access: Offline. AC INI-Param: MEDIACHANNELS |
| misc | 1.3.6.1.4.1.5003.9.10.3.1.1.11 | |||
| I32 miscASSubscribeIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.11.27 | Integer32 | read-write | IPGroup ID for AS server subscribe purposes. Access: Instant. AC INI-Param: ASSUBSCRIBEIPGROUPID |
| U32 miscCallForwardRingToneID | 1.3.6.1.4.1.5003.9.10.3.1.1.11.29 | Unsigned32 | read-write | Ringtone type for Call forward notification. Access: Instant. AC INI-Param: CALLFORWARDRINGTONEID |
| U32 miscDefaultReleaseCause | 1.3.6.1.4.1.5003.9.10.3.1.1.11.10 | Unsigned32 | read-write | The release cause that will be sent to IP or to Tel when gateway initiates release by itself. Access: Instant. AC INI-Param: DEFAULTRELEASECAUSE |
| U32 miscDelayTime | 1.3.6.1.4.1.5003.9.10.3.1.1.11.8 | Unsigned32 | read-write | Gateway delay time after reset (seconds). Access: Instant. AC INI-Param: GWAPPDelayTime |
| INT miscDetFaxOnAnswerTone | 1.3.6.1.4.1.5003.9.10.3.1.1.11.9 | INTEGER | read-write | Start T.38 fax procedure after fax answer tone detection or after HDLC preamble signal detection. Access: Instant. AC INI-Param: DETFAXONANSWERTONE |
| INT miscDisconnectOnBusyTone | 1.3.6.1.4.1.5003.9.10.3.1.1.11.1 | INTEGER | read-write | Release call if gateway receives busy or fast busy tone before the call is answered. Access: Instant. AC INI-Param: DISCONNECTONBUSYTONE |
| INT miscDisconnectOnDialTone | 1.3.6.1.4.1.5003.9.10.3.1.1.11.14 | INTEGER | read-write | Release call if gateway receives dial tone before the call is answered or during voice session. Access: Instant. AC INI-Param: DISCONNECTONDIALTONE |
| INT miscDisconnectOnSilence | 1.3.6.1.4.1.5003.9.10.3.1.1.11.2 | INTEGER | read-write | Disconnect calls on a configured silence timeout. Access: Offline. AC INI-Param: ENABLESILENCEDISCONNECT |
| INT miscEnableBusyOut | 1.3.6.1.4.1.5003.9.10.3.1.1.11.3 | INTEGER | read-write | Take trunks out of service in case of LAN down. Access: Instant. AC INI-Param: ENABLEBUSYOUT |
| INT miscEnableDelayedOffer | 1.3.6.1.4.1.5003.9.10.3.1.1.11.25 | INTEGER | read-write | Send INVITE message with/without sdp offer. [0] - (default) means SDP will be offered in the INVITE message. [1] - means SDP will be offered by the other side in the first reliable response(1xx or 200 OK INVITE). Access: Instant. AC INI-Param: ENABLEDELAYEDOFFER |
| INT miscEnableFaxRerouting | 1.3.6.1.4.1.5003.9.10.3.1.1.11.17 | INTEGER | read-write | Enable rerouting of FAX calls to FAX destination. Access: Instant. AC INI-Param: ENABLEFAXREROUTING |
| INT miscEnableNetworkISDNTransfer | 1.3.6.1.4.1.5003.9.10.3.1.1.11.33 | INTEGER | read-write | if set to 0 reject ISDN transfer request. Access: Instant. AC INI-Param: ENABLENETWORKISDNTRANSFER |
| INT miscEnableNRTSubscription | 1.3.6.1.4.1.5003.9.10.3.1.1.11.26 | INTEGER | read-write | Enable subscription for Call forward ringtone Indicator service. Access: Instant. AC INI-Param: ENABLENRTSUBSCRIPTION |
| INT miscEnableRFC4117Transcoding | 1.3.6.1.4.1.5003.9.10.3.1.1.11.31 | INTEGER | read-write | Enable transcoding call RFC4117. Access: Offline. AC INI-Param: ENABLERFC4117TRANSCODING |
| INT miscEnableSemiAttendedTransfer | 1.3.6.1.4.1.5003.9.10.3.1.1.11.15 | INTEGER | read-write | Access: Instant. AC INI-Param: ENABLESEMIATTENDEDTRANSFER |
| INT miscEnableSingleDSPTranscoding | 1.3.6.1.4.1.5003.9.10.3.1.1.11.32 | INTEGER | read-write | Enable/Disable using single DSP for g711 LBR coder. Access: Instant. AC INI-Param: ENABLESINGLEDSPTRANSCODING |
| INT miscFaxCNGMode | 1.3.6.1.4.1.5003.9.10.3.1.1.11.20 | INTEGER | read-write | Enables sending of ReInvite on detection of FAX CNG tone when CNGDetectorMode=1. Access: Instant. AC INI-Param: FAXCNGMODE |
| U32 miscGracefulBusyOutTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.11.21 | Unsigned32 | read-write | Graceful Busy Out Timeout in seconds. Sets the time before a busy out signal will be sent to a trunk even if there are still active calls on the trunk. Access: Instant. AC INI-Param: GRACEFULBUSYOUTTIMEOUT |
| STR miscHookFlashCodeIP | 1.3.6.1.4.1.5003.9.10.3.1.1.11.16 | SnmpAdminString | read-write | The string represent HookFlash, when reported to or from IP. Currently used in H.323 only (H245UserOutput, H245Signal or Q931UserInfo). Access: Instant. AC INI-Param: HookFlashCodeIP |
| INT miscIsCiscoSceMode | 1.3.6.1.4.1.5003.9.10.3.1.1.11.13 | INTEGER | read-write | In use with G.729 - if enabled and SCE=2 then AnnexB=no. Access: Instant. AC INI-Param: ISCISCOSCEMODE |
| INT miscIsdnDisconnectOnBusyTone | 1.3.6.1.4.1.5003.9.10.3.1.1.11.19 | INTEGER | read-write | 1 - Release call if gateway receives busy or fast busy tone. 0 - don't release. Access: Instant. AC INI-Param: ISDNDISCONNECTONBUSYTONE |
| INT miscIsFaxUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.11.7 | INTEGER | read-write | Enable T.38 Fax signaling. Access: Instant. AC INI-Param: IsFaxUsed |
| STR miscKeyCallPickup | 1.3.6.1.4.1.5003.9.10.3.1.1.11.30 | SnmpAdminString | read-write | Keying sequence for performing call pickup. Access: Instant. AC INI-Param: KEYCALLPICKUP |
| STR miscLDAPMobileNumberAttributeName | 1.3.6.1.4.1.5003.9.10.3.1.1.11.36 | SnmpAdminString | read-write | The name of the attribute which represents the user Mobile number in the Microsoft AD data base. Access: Instant. AC INI-Param: MSLDAPMOBILENUMATTRIBUTENAME |
| STR miscLDAPocsNumberAttributeName | 1.3.6.1.4.1.5003.9.10.3.1.1.11.34 | SnmpAdminString | read-write | The name of the attribute which represents the user OCS number in the Microsoft AD data base. Access: Instant. AC INI-Param: MSLDAPOCSNUMATTRIBUTENAME |
| STR miscLDAPpbxNumberAttributeName | 1.3.6.1.4.1.5003.9.10.3.1.1.11.35 | SnmpAdminString | read-write | The name of the attribute which represents the user PBX number in the Microsoft AD data base. Access: Instant. AC INI-Param: MSLDAPPBXNUMATTRIBUTENAME |
| U32 miscNRTSubscriptionRetryTime | 1.3.6.1.4.1.5003.9.10.3.1.1.11.28 | Unsigned32 | read-write | NRT service subscription retry time after last subscription failure (in seconds). Access: Instant. AC INI-Param: NRTSUBSCRIBERETRYTIME |
| INT miscReliableConnectionPersistentMode | 1.3.6.1.4.1.5003.9.10.3.1.1.11.23 | INTEGER | read-write | if set to 1 - All TCP/TLS connections will be set as persistent and will not be released. Access: Instant. AC INI-Param: RELIABLECONNECTIONPERSISTENTMODE |
| U32 miscRFC2833PayloadType | 1.3.6.1.4.1.5003.9.10.3.1.1.11.12 | Unsigned32 | read-write | control the RFC 2833 Relay RTP Payload type. Access: Instant. AC INI-Param: RFC2833PayloadType |
| INT miscSecureCallsFromIp | 1.3.6.1.4.1.5003.9.10.3.1.1.11.4 | INTEGER | read-write | Gateway will only accept calls from IP addresses that are defined in the Tel to IP Routing table. Access: Instant. AC INI-Param: SECURECALLSFROMIP |
| U32 miscSilenceDisconnectTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.11.6 | Unsigned32 | read-write | Defines the Silence period to be detected. Access: Offline. AC INI-Param: FarEndDisconnectSilencePeriod |
| STR miscStaticNATIP | 1.3.6.1.4.1.5003.9.10.3.1.1.11.5 | SnmpAdminString | read-write | static NAT IP, to be supported by the gateway. Access: Instant. AC INI-Param: STATICNATIP |
| U32 miscT38FaxMaxBufferSize | 1.3.6.1.4.1.5003.9.10.3.1.1.11.22 | Unsigned32 | read-write | Defines the fax max buffer size in T38 SDP negotiation. Access: Instant. AC INI-Param: T38FAXMAXBUFFERSIZE |
| U32 miscT38MaxDatagramSize | 1.3.6.1.4.1.5003.9.10.3.1.1.11.18 | Unsigned32 | read-write | T.38 coder - Max Datagram Size. Access: Instant. AC INI-Param: T38MAXDATAGRAMSIZE |
| INT miscT38UseRTPPort | 1.3.6.1.4.1.5003.9.10.3.1.1.11.11 | INTEGER | read-write | T.38 packets will be received on RTP port. Access: Instant. AC INI-Param: T38USERTPPORT |
| IP miscWANIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.11.24 | InetAddress | read-write | Sets the WAN address to be used by VOIP signalling applications. Range = IPv4 address in dotted decimal notation xxx.xxx.xxx.xxx Default = 0.0.0.0. Access: Instant. AC INI-Param: WANIPAddress |
| mlpp | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29 | |||
| INT mlppCallPriorityMode | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.1 | INTEGER | read-write | Priority mode: 0-disable 1-MLPP. Access: Instant. AC INI-Param: CALLPRIORITYMODE |
| STR mlppDefaultCallPriority | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.3 | SnmpAdminString | read-write | SIP Default Call Priority. Access: Instant. AC INI-Param: SIPDEFAULTCALLPRIORITY |
| INT mlppDefaultNamespace | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.2 | INTEGER | read-write | MLPP Default Namespace. Access: Instant. AC INI-Param: MLPPDEFAULTNAMESPACE |
| STR mlppDefaultServiceDomain | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.6 | SnmpAdminString | read-write | MLPP Default Service Domain String (6 Hex Digits). Access: Instant. AC INI-Param: MLPPDefaultServiceDomain |
| U32 mlppDiffServ | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.4 | Unsigned32 | read-write | DiffServ value for MLPP calls. Access: Instant. AC INI-Param: MLPPDIFFSERV |
| INT mlppE911Behavior | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.14 | INTEGER | read-write | Defines the MLPP E911 Preemption mode: (0)-Standard Mode (ets calls will have the highest priority and can preemt any mlpp call), (1)-Treat as routine mode (ets calls are treated as routine calls). Access: Instant. AC INI-Param: E911MLPPBEHAVIOR |
| I32 mlppFlashOverOverRTPDSCP | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.13 | Integer32 | read-write | Defines the RTP DSCP for MLPP Flash-Override-Override call. Access: Instant. AC INI-Param: MLPPFLASHOVEROVERRTPDSCP |
| I32 mlppFlashOverRTPDSCP | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.12 | Integer32 | read-write | Defines the RTP DSCP for MLPP Flash-Override call. Access: Instant. AC INI-Param: MLPPFLASHOVERRTPDSCP |
| I32 mlppFlashRTPDSCP | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.11 | Integer32 | read-write | Defines the RTP DSCP for MLPP Flash call. Access: Instant. AC INI-Param: MLPPFLASHRTPDSCP |
| I32 mlppImmediateRTPDSCP | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.10 | Integer32 | read-write | Defines the RTP DSCP for MLPP Immediate call. Access: Instant. AC INI-Param: MLPPIMMEDIATERTPDSCP |
| STR mlppNormalizedServiceDomain | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.7 | SnmpAdminString | read-write | MLPP Normalized Service Domain String (6 Hex Digits). Access: Instant. AC INI-Param: MLPPNormalizedServiceDomain |
| U32 mlppPreemptionToneDuration | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.5 | Unsigned32 | read-write | Preemption Tone Duration, 0-60 seconds. Access: Instant. AC INI-Param: PreemptionToneDuration |
| I32 mlppPriorityRTPDSCP | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.9 | Integer32 | read-write | Defines the RTP DSCP for MLPP Priority call. Access: Instant. AC INI-Param: MLPPPRIORITYRTPDSCP |
| I32 mlppRoutineRTPDSCP | 1.3.6.1.4.1.5003.9.10.3.1.1.3.29.8 | Integer32 | read-write | Defines the RTP DSCP for MLPP Routine call. Access: Instant. AC INI-Param: MLPPROUTINERTPDSCP |
| mWI | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13 | |||
| INT mWIAnalogLamp | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13.2 | INTEGER | read-write | Enable MWI support using an analog lamp (110 Volt). Access: Instant. AC INI-Param: MWIANALOGLAMP |
| INT mWIDisplay | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13.3 | INTEGER | read-write | Enable MWI support using Caller ID interface. Access: Instant. AC INI-Param: MWIDISPLAY |
| INT mWIEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13.1 | INTEGER | read-write | Enable MWI support (Message Waiting Indicator). Access: Instant. AC INI-Param: ENABLEMWI |
| U32 mWIExpirationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13.5 | Unsigned32 | read-write | MWI service subscription expiration time (seconds). Access: Instant. AC INI-Param: MWIEXPIRATIONTIME |
| STR mWIServerIP | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13.4 | SnmpAdminString | read-write | MWI server IP address. Access: Instant. AC INI-Param: MWISERVERIP |
| INT mWIServerTransportType | 1.3.6.1.4.1.5003.9.10.3.1.1.7.13.6 | INTEGER | read-write | MWI server transport type. Access: Instant. AC INI-Param: MWISERVERTRANSPORTTYPE |
| INT namesAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT namesActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| namesEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1 | not-accessible | ||
| U32 namesIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.1 | Unsigned32 | read-only | Entry number, starting at 0. AC INI-Param: PortName_Index |
| INT namesIsUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.2 | INTEGER | read-write | Is this index used. AC INI-Param: PortName_IsUsed |
| U32 namesModule | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.6 | Unsigned32 | read-only | Module. AC INI-Param: PortName_Module |
| U32 namesPort | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.7 | Unsigned32 | read-only | Port. AC INI-Param: PortName_Port |
| STR namesPortName | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21.1.5 | SnmpAdminString | read-write | Access: Instant. AC INI-Param: PortName_Name |
| namesTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15.21 | not-accessible | ||
| INT phoneContextAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT phoneContextActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| phoneContextEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1 | not-accessible | ||
| U32 phoneContextIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: PhoneContext_Index |
| INT phoneContextNPI | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.5 | INTEGER | read-create | Number Plan. Access: Instant. AC INI-Param: PhoneContext_Npi |
| STR phoneContextPhoneContext | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.7 | SnmpAdminString | read-create | Phone-Context. Access: Instant. AC INI-Param: PhoneContext_Context |
| ROW phoneContextRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| phoneContextTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25 | not-accessible | ||
| INT phoneContextTON | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.25.1.6 | INTEGER | read-create | Number Type. Access: Instant. AC INI-Param: PhoneContext_Ton |
| pIForDisconnectMsgEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.27.1 | not-accessible | ||
| U32 pIForDisconnectMsgIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.27.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| pIForDisconnectMsgTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.27 | not-accessible | PI For Disconnect Message Trunk table. | |
| I32 pIForDisconnectMsgValue | 1.3.6.1.4.1.5003.9.10.3.1.1.3.27.1.2 | Integer32 | read-write | Configure PIForDisconnectMsg in order to overwrite PI value received in ISDN Disconnect message. Access: Instant. AC INI-Param: PIFORDISCONNECTMSG |
| playRBToneToTrunkEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.24.1 | not-accessible | ||
| U32 playRBToneToTrunkIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.24.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| playRBToneToTrunkTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.24 | not-accessible | Play RB Tone To Trunk table. | |
| INT playRBToneToTrunkValue | 1.3.6.1.4.1.5003.9.10.3.1.1.3.24.1.2 | INTEGER | read-write | Enable ringback tone playing towards trunk side. Refer to User's Manual for details. Access: Instant. AC INI-Param: PLAYRBTONE2TRUNK |
| portName | 1.3.6.1.4.1.5003.9.10.3.1.1.4.15 | |||
| profile | 1.3.6.1.4.1.5003.9.10.3.1.1.15 | |||
| progressIndicators | 1.3.6.1.4.1.5003.9.10.3.1.1.10 | |||
| INT progressIndicators2IP | 1.3.6.1.4.1.5003.9.10.3.1.1.10.2 | INTEGER | read-write | Determine whether to send the Progress Indicator to IP. Access: Instant. AC INI-Param: PROGRESSINDICATOR2IP |
| INT progressIndicators2ISDN | 1.3.6.1.4.1.5003.9.10.3.1.1.10.1 | INTEGER | read-write | Override the value of progress indicator to ISDN side in ALERT PROGRESS and PROCEEDING messages. Access: Instant. AC INI-Param: PROGRESSINDICATOR2ISDN |
| progressIndicatorToISDNEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.23.1 | not-accessible | ||
| U32 progressIndicatorToISDNIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.23.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| progressIndicatorToISDNTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.23 | not-accessible | Progress Indicator To ISDN table. | |
| INT progressIndicatorToISDNValue | 1.3.6.1.4.1.5003.9.10.3.1.1.3.23.1.2 | INTEGER | read-write | Override the value of progress indicator to ISDN side in ALERT PROGRESS and PROCEEDING messages. Access: Instant. AC INI-Param: PROGRESSINDICATOR2ISDN |
| INT proxyIPAction | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT proxyIPActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| proxyIPEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21.1 | not-accessible | ||
| U32 proxyIPIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: ProxyIp_Index |
| STR proxyIPProxyIP | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: ProxyIp_IpAddress |
| ROW proxyIPRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| proxyIPTable | 1.3.6.1.4.1.5003.9.10.3.1.2.1.21 | not-accessible | The table defines phone numbers for gateway endpoints. The endpoints that aren�t defined will be disabled. | |
| pSTNAlertTimeoutEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.28.1 | not-accessible | ||
| U32 pSTNAlertTimeoutIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.28.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| pSTNAlertTimeoutTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.28 | not-accessible | PSTN Alert Timeout | |
| I32 pSTNAlertTimeoutValue | 1.3.6.1.4.1.5003.9.10.3.1.1.3.28.1.2 | Integer32 | read-write | Max time (in seconds) to wait for connect from PSTN. Access: Instant. AC INI-Param: TRUNKPSTNALERTTIMEOUT |
| INT redirectNumberMapIp2TelAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT redirectNumberMapIp2TelActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR redirectNumberMapIp2TelDestinationPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_DestinationPrefix |
| redirectNumberMapIp2TelEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1 | not-accessible | ||
| U32 redirectNumberMapIp2TelIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: RedirectNumberMapIp2Tel_Index |
| INT redirectNumberMapIp2TelIsPresentationRestricted | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.15 | INTEGER | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_IsPresentationRestricted |
| U32 redirectNumberMapIp2TelLeaveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.12 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_LeaveFromRight |
| INT redirectNumberMapIp2TelNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.9 | INTEGER | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_NumberPlan |
| INT redirectNumberMapIp2TelNumberType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.8 | INTEGER | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_NumberType |
| STR redirectNumberMapIp2TelPrefixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.13 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_Prefix2Add |
| STR redirectNumberMapIp2TelRedirectPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.6 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_RedirectPrefix |
| U32 redirectNumberMapIp2TelRemoveFromLeft | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.10 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_RemoveFromLeft |
| U32 redirectNumberMapIp2TelRemoveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.11 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_RemoveFromRight |
| ROW redirectNumberMapIp2TelRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| STR redirectNumberMapIp2TelSourceAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.7 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_SourceAddress |
| I32 redirectNumberMapIp2TelSrcIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.17 | Integer32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_SrcIPGroupID |
| I32 redirectNumberMapIp2TelSrcTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.16 | Integer32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_SrcTrunkGroupID |
| STR redirectNumberMapIp2TelSuffixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26.1.14 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapIp2Tel_Suffix2Add |
| redirectNumberMapIp2TelTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.26 | not-accessible | GwApp IP-to-Tel Redirect Phone Number Manipulation Rules Table | |
| INT redirectNumberMapTel2IpAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT redirectNumberMapTel2IpActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR redirectNumberMapTel2IpDestinationPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_DestinationPrefix |
| redirectNumberMapTel2IpEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1 | not-accessible | ||
| U32 redirectNumberMapTel2IpIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: RedirectNumberMapTel2Ip_Index |
| INT redirectNumberMapTel2IpIsPresentationRestricted | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.15 | INTEGER | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_IsPresentationRestricted |
| U32 redirectNumberMapTel2IpLeaveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.12 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_LeaveFromRight |
| U32 redirectNumberMapTel2IpNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.9 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_NumberPlan |
| U32 redirectNumberMapTel2IpNumberType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.8 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_NumberType |
| STR redirectNumberMapTel2IpPrefixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.13 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_Prefix2Add |
| STR redirectNumberMapTel2IpRedirectPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.6 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_RedirectPrefix |
| U32 redirectNumberMapTel2IpRemoveFromLeft | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.10 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_RemoveFromLeft |
| U32 redirectNumberMapTel2IpRemoveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.11 | Unsigned32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_RemoveFromRight |
| ROW redirectNumberMapTel2IpRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| STR redirectNumberMapTel2IpSourceAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.7 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_SourceAddress |
| I32 redirectNumberMapTel2IpSrcIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.17 | Integer32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_SrcIPGroupID |
| I32 redirectNumberMapTel2IpSrcTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.16 | Integer32 | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_SrcTrunkGroupID |
| STR redirectNumberMapTel2IpSuffixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27.1.14 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: RedirectNumberMapTel2Ip_Suffix2Add |
| redirectNumberMapTel2IpTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.27 | not-accessible | GwApp Tel-to-IP Redirect Phone Number Manipulation Rules Table | |
| INT registerPrefixAction | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT registerPrefixActionResult | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| registerPrefixEntry | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1 | not-accessible | ||
| U32 registerPrefixIndex | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: RegistrationPrefix_Index |
| INT registerPrefixNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.6 | INTEGER | read-create | Number Plan that will be used when Registration Type is PartyNumber. Access: Instant. AC INI-Param: RegistrationPrefix_NumberPlan |
| INT registerPrefixNumberType | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.7 | INTEGER | read-create | Number Type that will be used when Registration Type is PartyNumber. Access: Instant. AC INI-Param: RegistrationPrefix_NumberType |
| STR registerPrefixPrefix | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.5 | SnmpAdminString | read-create | Usually the prefixes will define range of PSTN/PBX phone numbers that the gateway can handle. Access: Offline. AC INI-Param: RegistrationPrefix_Prefix |
| ROW registerPrefixRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22.1.2 | RowStatus | read-create | This object allows entries to be created and deleted from the table. For Reference: RFC 1903, Textual Conventions for Version 2 of the Simple Network Management Protocol (SNMPv2). Access: Instant. AC INI-Param: N/A |
| registerPrefixTable | 1.3.6.1.4.1.5003.9.10.3.1.3.11.22 | not-accessible | The registration prefixes are applicable for Digital E1/T1 and FXO gateways for registration to Gatekeeper. If not used the gateway will register with its endpoint phone numbers. | |
| resourceManagement | 1.3.6.1.4.1.5003.9.10.3.1.1.12 | |||
| INT resourceManagementDisconnectOnBrokenConnection | 1.3.6.1.4.1.5003.9.10.3.1.1.12.4 | INTEGER | read-write | Disconnect calls on receiving RTP broken notification. Access: Instant. AC INI-Param: DISCONNECTONBROKENCONNECTION |
| INT resourceManagementIsSelfCheckAuditUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.12.2 | INTEGER | read-write | defines whether the resources self check audit is used. Access: Instant. AC INI-Param: ISSELFCHECKAUDITUSED |
| U32 resourceManagementMaxActiveCalls | 1.3.6.1.4.1.5003.9.10.3.1.1.12.1 | Unsigned32 | read-write | Limit the number of calls that the gateway can handle at the same time. Access: Instant. AC INI-Param: MAXACTIVECALLS |
| U32 resourceManagementMaxCallDuration | 1.3.6.1.4.1.5003.9.10.3.1.1.12.5 | Unsigned32 | read-write | Limit the call time duration (minutes) 0 = no limit. Access: Instant. AC INI-Param: MAXCALLDURATION |
| INT resourceManagementOverloadSensitivityLevel | 1.3.6.1.4.1.5003.9.10.3.1.1.12.6 | INTEGER | read-write | Defines when to enter overload state: 0:never 1:on very high utilization 2:on medium utilization. Access: Instant. AC INI-Param: OverloadSensitivityLevel |
| INT resourceManagementRejectCallsOnOverload | 1.3.6.1.4.1.5003.9.10.3.1.1.12.3 | INTEGER | read-write | Defines whether new calls will be rejected during overload period. Access: Instant. AC INI-Param: REJECTCALLSONOVERLOAD |
| routing | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20 | |||
| INT routingEnableDigitDelivery2IP | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.21 | INTEGER | read-write | Enable automatic digit delivery to IP side after call is connected. Access: Offline. AC INI-Param: ENABLEDIGITDELIVERY2IP |
| INT routingSourceIPAddressInput | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.22 | INTEGER | read-write | Decides the origin of the source ip address looked at when routing using the IP --> Tel table. 0 - Contact 1 - Recieved packet source IP address. Access: Instant. AC INI-Param: SOURCEIPADDRESSINPUT |
| rtpOnlyModeForTrunkEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.17.21.1 | not-accessible | ||
| U32 rtpOnlyModeForTrunkIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.17.21.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| INT rtpOnlyModeForTrunkRtpOnlyModeForTrunk | 1.3.6.1.4.1.5003.9.10.3.1.1.17.21.1.2 | INTEGER | read-write | immediately. -1 - takes the RTPONLYMODE global value per gatewa 0 - regular call establishment. 1 - The RTP channel open for Rx & Tx. 2-The RTP channel open only for Tx 3 -The RTP channel open only fo Rx. Access: Instant. AC INI-Param: RTPONLYMODEFORTRUNK |
| rtpOnlyModeForTrunkTable | 1.3.6.1.4.1.5003.9.10.3.1.1.17.21 | not-accessible | ||
| INT sasRegistrationManipulationAction | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sasRegistrationManipulationActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| sasRegistrationManipulationEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1 | not-accessible | ||
| U32 sasRegistrationManipulationIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1.1 | Unsigned32 | not-accessible | AC INI-Param: SASRegistrationManipulation_Index |
| U32 sasRegistrationManipulationLeaveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1.6 | Unsigned32 | read-create | Access: Instant. AC INI-Param: SASRegistrationManipulation_LeaveFromRight |
| U32 sasRegistrationManipulationRemoveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1.5 | Unsigned32 | read-create | Access: Instant. AC INI-Param: SASRegistrationManipulation_RemoveFromRight |
| ROW sasRegistrationManipulationRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| sasRegistrationManipulationTable | 1.3.6.1.4.1.5003.9.10.3.1.2.10.21 | not-accessible | GWAPP SAS Registration Manipulation Table. | |
| sbc | 1.3.6.1.4.1.5003.9.10.3.1.1.24 | |||
| INT sbcAdmissionControlAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcAdmissionControlActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| sbcAdmissionControlEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1 | not-accessible | ||
| U32 sbcAdmissionControlIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.1 | Unsigned32 | read-only | . AC INI-Param: SBCAdmissionControl_Index |
| I32 sbcAdmissionControlIpGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.6 | Integer32 | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_IPGroupID |
| I32 sbcAdmissionControlLimit | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.10 | Integer32 | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_Limit |
| I32 sbcAdmissionControlLimitPerUser | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.11 | Integer32 | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_LimitPerUser |
| INT sbcAdmissionControlLimitType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.5 | INTEGER | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_LimitType |
| INT sbcAdmissionControlRequestDirection | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.9 | INTEGER | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_RequestDirection |
| INT sbcAdmissionControlRequestType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.8 | INTEGER | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_RequestType |
| ROW sbcAdmissionControlRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| I32 sbcAdmissionControlSrdID | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25.1.7 | Integer32 | read-create | Access: Instant. AC INI-Param: SBCAdmissionControl_SRDID |
| sbcAdmissionControlTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.25 | not-accessible | GwApp SBC SIP Admission Control Table | |
| INT sbcAlternativeRoutingReasonsAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcAlternativeRoutingReasonsActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| sbcAlternativeRoutingReasonsEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27.1 | not-accessible | ||
| U32 sbcAlternativeRoutingReasonsIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27.1.1 | Unsigned32 | read-only | . AC INI-Param: SBCAlternativeRoutingReasons_Index |
| U32 sbcAlternativeRoutingReasonsReleaseCause | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27.1.5 | Unsigned32 | read-create | Release Cause. Access: Instant. AC INI-Param: SBCAlternativeRoutingReasons_ReleaseCause |
| ROW sbcAlternativeRoutingReasonsRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| sbcAlternativeRoutingReasonsTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.27 | not-accessible | GwApp Reasons For Alternative Routing For SBC Application(IP to IP) Table | |
| INT sbcClassificationAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcClassificationActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR sbcClassificationDestHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.11 | SnmpAdminString | read-create | Destination host. Access: Instant. AC INI-Param: Classification_DestHost |
| STR sbcClassificationDestUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.10 | SnmpAdminString | read-create | Destination username prefix. Access: Instant. AC INI-Param: Classification_DestUsernamePrefix |
| sbcClassificationEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1 | not-accessible | ||
| U32 sbcClassificationIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.1 | Unsigned32 | read-only | . AC INI-Param: Classification_Index |
| ROW sbcClassificationRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR sbcClassificationSrcAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.7 | SnmpAdminString | read-create | Source address. Access: Instant. AC INI-Param: Classification_SrcAddress |
| STR sbcClassificationSrcHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.9 | SnmpAdminString | read-create | Source host. Access: Instant. AC INI-Param: Classification_SrcHost |
| I32 sbcClassificationSrcIPGroupId | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.5 | Integer32 | read-create | Source IP group ID. Access: Instant. AC INI-Param: Classification_SrcIPGroupID |
| I32 sbcClassificationSrcSRDId | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.6 | Integer32 | read-create | Source SRD ID. Access: Instant. AC INI-Param: Classification_SrcSRDID |
| STR sbcClassificationSrcUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21.1.8 | SnmpAdminString | read-create | Source username prefix. Access: Instant. AC INI-Param: Classification_SrcUsernamePrefix |
| sbcClassificationTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.21 | not-accessible | GwApp Classification Table | |
| INT sbcEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.1 | INTEGER | read-write | Enables SBC functionality. Access: Instant. AC INI-Param: ENABLESBC |
| INT sbcEnableIIP2IPApplication | 1.3.6.1.4.1.5003.9.10.3.1.1.24.4 | INTEGER | read-write | Enables IP2IP functionality. Access: Offline. AC INI-Param: ENABLEIP2IPAPPLICATION |
| INT sbcEnableISBCApplication | 1.3.6.1.4.1.5003.9.10.3.1.1.24.3 | INTEGER | read-write | Enables SBC functionality. Access: Offline. AC INI-Param: ENABLESBCAPPLICATION |
| INT sbcIP2IPInboundManipulationAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcIP2IPInboundManipulationActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR sbcIP2IPInboundManipulationDestHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.11 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_DestHost |
| STR sbcIP2IPInboundManipulationDestUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.10 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_DestUsernamePrefix |
| sbcIP2IPInboundManipulationEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1 | not-accessible | ||
| U32 sbcIP2IPInboundManipulationIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.1 | Unsigned32 | read-only | . AC INI-Param: IPInboundManipulation_Index |
| INT sbcIP2IPInboundManipulationIsAdditionalManipulation | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.5 | INTEGER | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_IsAdditionalManipulation |
| U32 sbcIP2IPInboundManipulationLeaveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.14 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_LeaveFromRight |
| INT sbcIP2IPInboundManipulationManipulatedURI | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.6 | INTEGER | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_ManipulatedURI |
| STR sbcIP2IPInboundManipulationPrefix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.15 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_Prefix2Add |
| U32 sbcIP2IPInboundManipulationRemoveFromLeft | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.12 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_RemoveFromLeft |
| U32 sbcIP2IPInboundManipulationRemoveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.13 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_RemoveFromRight |
| INT sbcIP2IPInboundManipulationRequestType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.17 | INTEGER | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_RequestType |
| ROW sbcIP2IPInboundManipulationRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR sbcIP2IPInboundManipulationSrcHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.9 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_SrcHost |
| I32 sbcIP2IPInboundManipulationSrcIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.7 | Integer32 | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_SrcIPGroupID |
| STR sbcIP2IPInboundManipulationSrcUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.8 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_SrcUsernamePrefix |
| STR sbcIP2IPInboundManipulationSuffix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23.1.16 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPInboundManipulation_Suffix2Add |
| sbcIP2IPInboundManipulationTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.23 | not-accessible | GwApp IP Inbound Manipulation Table | |
| INT sbcIP2IPOutboundManipulationAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcIP2IPOutboundManipulationActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR sbcIP2IPOutboundManipulationDestHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.12 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_DestHost |
| I32 sbcIP2IPOutboundManipulationDestIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.8 | Integer32 | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_DestIPGroupID |
| STR sbcIP2IPOutboundManipulationDestUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.11 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_DestUsernamePrefix |
| sbcIP2IPOutboundManipulationEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1 | not-accessible | ||
| U32 sbcIP2IPOutboundManipulationIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.1 | Unsigned32 | read-only | . AC INI-Param: IPOutboundManipulation_Index |
| INT sbcIP2IPOutboundManipulationIsAdditionalManipulation | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.5 | INTEGER | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_IsAdditionalManipulation |
| U32 sbcIP2IPOutboundManipulationLeaveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.15 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_LeaveFromRight |
| INT sbcIP2IPOutboundManipulationManipulatedURI | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.6 | INTEGER | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_ManipulatedURI |
| STR sbcIP2IPOutboundManipulationPrefix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.16 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_Prefix2Add |
| U32 sbcIP2IPOutboundManipulationRemoveFromLeft | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.13 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_RemoveFromLeft |
| U32 sbcIP2IPOutboundManipulationRemoveFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.14 | Unsigned32 | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_RemoveFromRight |
| INT sbcIP2IPOutboundManipulationRequestType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.18 | INTEGER | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_RequestType |
| ROW sbcIP2IPOutboundManipulationRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR sbcIP2IPOutboundManipulationSrcHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.10 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_SrcHost |
| I32 sbcIP2IPOutboundManipulationSrcIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.7 | Integer32 | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_SrcIPGroupID |
| STR sbcIP2IPOutboundManipulationSrcUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.9 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_SrcUsernamePrefix |
| STR sbcIP2IPOutboundManipulationSuffix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24.1.17 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: IPOutboundManipulation_Suffix2Add |
| sbcIP2IPOutboundManipulationTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.24 | not-accessible | GwApp IP Outbound Manipulation Table | |
| INT sbcMessageManipulationsAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcMessageManipulationsActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR sbcMessageManipulationsActionSubject | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.8 | SnmpAdminString | read-create | Message manipulation Action Subject. Access: Instant. AC INI-Param: MessageManipulations_ActionSubject |
| INT sbcMessageManipulationsActionType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.9 | INTEGER | read-create | Message manipulation Action type. Access: Instant. AC INI-Param: MessageManipulations_ActionType |
| STR sbcMessageManipulationsActionValue | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.10 | SnmpAdminString | read-create | Message manipulation Action value. Access: Instant. AC INI-Param: MessageManipulations_ActionValue |
| STR sbcMessageManipulationsCondition | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.7 | SnmpAdminString | read-create | Message manipulation Condition. Access: Instant. AC INI-Param: MessageManipulations_Condition |
| sbcMessageManipulationsEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1 | not-accessible | ||
| U32 sbcMessageManipulationsIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.1 | Unsigned32 | read-only | . AC INI-Param: MessageManipulations_Index |
| U32 sbcMessageManipulationsManipulationSetID | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.5 | Unsigned32 | read-create | Manipulation Set ID. Access: Instant. AC INI-Param: MessageManipulations_ManSetID |
| STR sbcMessageManipulationsMessageType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.6 | SnmpAdminString | read-create | Message type. Access: Instant. AC INI-Param: MessageManipulations_MessageType |
| INT sbcMessageManipulationsRowRole | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.11 | INTEGER | read-create | Message manipulation row rule. Access: Instant. AC INI-Param: MessageManipulations_RowRole |
| ROW sbcMessageManipulationsRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| sbcMessageManipulationsTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.26 | not-accessible | SBC Message Manipulations Table. | |
| U32 sbcRegistrationTime | 1.3.6.1.4.1.5003.9.10.3.1.1.24.2 | Unsigned32 | read-write | Expires value SBC responds to user with. Used when server is offline or when the user is behind NAT. Otherwise expires is defined by the server. Access: Instant. AC INI-Param: SBCREGISTRATIONTIME |
| INT sbcRoutingAction | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcRoutingActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sbcRoutingAltRouteOptions | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.16 | INTEGER | read-create | Alternative Route Options. Access: Instant. AC INI-Param: IP2IPRouting_AltRouteOptions |
| STR sbcRoutingDestAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.13 | SnmpAdminString | read-create | Destination Address. Access: Instant. AC INI-Param: IP2IPRouting_DestAddress |
| STR sbcRoutingDestHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.9 | SnmpAdminString | read-create | Destination host. Access: Instant. AC INI-Param: IP2IPRouting_DestHost |
| I32 sbcRoutingDestIPGroupId | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.11 | Integer32 | read-create | Destination IP group ID. Access: Instant. AC INI-Param: IP2IPRouting_DestIPGroupID |
| U32 sbcRoutingDestPort | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.14 | Unsigned32 | read-create | Destination Port number. Access: Instant. AC INI-Param: IP2IPRouting_DestPort |
| I32 sbcRoutingDestSRDId | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.12 | Integer32 | read-create | Destination SRD ID. Access: Instant. AC INI-Param: IP2IPRouting_DestSRDID |
| INT sbcRoutingDestTransportType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.15 | INTEGER | read-create | Destination transport type. Access: Instant. AC INI-Param: IP2IPRouting_DestTransportType |
| INT sbcRoutingDestType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.10 | INTEGER | read-create | Destination type. Access: Instant. AC INI-Param: IP2IPRouting_DestType |
| STR sbcRoutingDestUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.8 | SnmpAdminString | read-create | Destination username prefix. Access: Instant. AC INI-Param: IP2IPRouting_DestUsernamePrefix |
| sbcRoutingEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1 | not-accessible | ||
| U32 sbcRoutingIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.1 | Unsigned32 | read-only | . AC INI-Param: IP2IPRouting_Index |
| INT sbcRoutingRequestType | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.17 | INTEGER | read-create | Request Type. Access: Instant. AC INI-Param: IP2IPRouting_RequestType |
| ROW sbcRoutingRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR sbcRoutingSrcHost | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.7 | SnmpAdminString | read-create | Source host. Access: Instant. AC INI-Param: IP2IPRouting_SrcHost |
| I32 sbcRoutingSrcIPGroupId | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.5 | Integer32 | read-create | Source IP group ID. Access: Instant. AC INI-Param: IP2IPRouting_SrcIPGroupID |
| STR sbcRoutingSrcUsernamePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22.1.6 | SnmpAdminString | read-create | Source username prefix. Access: Instant. AC INI-Param: IP2IPRouting_SrcUsernamePrefix |
| sbcRoutingTable | 1.3.6.1.4.1.5003.9.10.3.1.1.24.22 | not-accessible | GwApp SBC Routing Table | |
| screeningIndicators | 1.3.6.1.4.1.5003.9.10.3.1.1.10.20 | |||
| INT screeningIndicators2Ip | 1.3.6.1.4.1.5003.9.10.3.1.1.10.20.1 | INTEGER | read-write | Override screening indicator value in Setup messages to IP. Access: Instant. AC INI-Param: SCREENINGIND2IP |
| INT screeningIndicators2ISDN | 1.3.6.1.4.1.5003.9.10.3.1.1.10.20.2 | INTEGER | read-write | Override screening indicator value in Setup messages to ISDN. Access: Instant. AC INI-Param: SCREENINGIND2ISDN |
| sip | 1.3.6.1.4.1.5003.9.10.3.1.2 | |||
| sipAuth | 1.3.6.1.4.1.5003.9.10.3.1.2.4 | |||
| INT sipAuthChallengeCachingMode | 1.3.6.1.4.1.5003.9.10.3.1.2.4.6 | INTEGER | read-write | 0. No caching mode � don't cache any challenges. Every new request will be sent without preliminary authorization. If the request is challenged � new request with authorization data will be sent. 1. Cache for INVITE mode � challenges issued for INVITE request and within the session will be cached. This will prevent the mixture of REGISTER and INVITE authorizations. 2. Full cache mode � cache any challenges from the proxies. . Access: Instant. AC INI-Param: SIPCHALLENGECACHINGMODE |
| STR sipAuthCnonce | 1.3.6.1.4.1.5003.9.10.3.1.2.4.4 | SnmpAdminString | read-write | Cnonce parameter used for authentication. Access: Instant. AC INI-Param: CNONCE |
| INT sipAuthMode | 1.3.6.1.4.1.5003.9.10.3.1.2.4.1 | INTEGER | read-write | Authentication mode. Access: Instant. AC INI-Param: AUTHENTICATIONMODE |
| INT sipAuthMutualAuthenticationMode | 1.3.6.1.4.1.5003.9.10.3.1.2.4.5 | INTEGER | read-write | Mutual Authentication Mode: 0 - Optional, 1 - Mandatory. Access: Instant. AC INI-Param: MUTUALAUTHENTICATIONMODE |
| STR sipAuthPassword | 1.3.6.1.4.1.5003.9.10.3.1.2.4.3 | SnmpAdminString | read-write | Password used for authentication. Access: Instant. AC INI-Param: PASSWORD |
| STR sipAuthUserName | 1.3.6.1.4.1.5003.9.10.3.1.2.4.2 | SnmpAdminString | read-write | User Name used for authentication. Access: Instant. AC INI-Param: USERNAME |
| sipDigitalGW | 1.3.6.1.4.1.5003.9.10.3.1.2.9 | |||
| sipDTMF | 1.3.6.1.4.1.5003.9.10.3.1.2.2 | |||
| INT sipDTMFDisableAutoMute | 1.3.6.1.4.1.5003.9.10.3.1.2.2.4 | INTEGER | read-write | Disables inband auto mute of DTMFs when signalling is used for sending DTMFs. Access: Instant. AC INI-Param: DISABLEAUTODTMFMUTE |
| INT sipDTMFHookFlashOption | 1.3.6.1.4.1.5003.9.10.3.1.2.2.6 | INTEGER | read-write | Detect and send Hook-Flash using the selected method. Access: Instant. AC INI-Param: HOOKFLASHOPTION |
| INT sipDTMFISDNOverlapIPtoTelDialing | 1.3.6.1.4.1.5003.9.10.3.1.2.2.9 | INTEGER | read-write | Enable ISDN Overlap IP to Tel Dialing. Access: Instant. AC INI-Param: ISDNTXOVERLAP |
| INT sipDTMFIsDTMFUsed | 1.3.6.1.4.1.5003.9.10.3.1.2.2.2 | INTEGER | read-write | Send DTMFs on the Signaling path (not on the Media path). Access: Instant. AC INI-Param: ISDTMFUSED |
| INT sipDTMFIsHookFlashUsed | 1.3.6.1.4.1.5003.9.10.3.1.2.2.1 | INTEGER | read-write | Detect and send Hook-Flash as Out-of-Band message. Access: Instant. AC INI-Param: ISHOOKFLASHUSED |
| U32 sipDTMFMinRoutingOverlapDigits | 1.3.6.1.4.1.5003.9.10.3.1.2.2.8 | Unsigned32 | read-write | Minimum number of overlap digits before routing. Access: Instant. AC INI-Param: MINOVERLAPDIGITSFORROUTING |
| INT sipDTMFOutOfBandDtmfFormat | 1.3.6.1.4.1.5003.9.10.3.1.2.2.3 | INTEGER | read-write | DTMF Out-of-Band transport method. Access: Instant. AC INI-Param: OUTOFBANDDTMFFORMAT |
| INT sipDTMFRxDTMFOption | 1.3.6.1.4.1.5003.9.10.3.1.2.2.5 | INTEGER | read-write | Declare support for RFC 2833 in SDP. Access: Instant. AC INI-Param: RXDTMFOPTION |
| INT sipDTMFUseDigitForSpecialDTMF | 1.3.6.1.4.1.5003.9.10.3.1.2.2.7 | INTEGER | read-write | Indicates whether a special DTMF, sent with INFO(Cisco), is sent using its digit representation or not. Access: Instant. AC INI-Param: USEDIGITFORSPECIALDTMF |
| INT sipInterfaceAction | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sipInterfaceActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sipInterfaceApplicationType | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.6 | INTEGER | read-create | Application Type. Access: Instant. AC INI-Param: SIPInterface_ApplicationType |
| sipInterfaceEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1 | not-accessible | ||
| U32 sipInterfaceIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.1 | Unsigned32 | read-only | . AC INI-Param: SIPInterface_Index |
| STR sipInterfaceNetworkInterface | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.5 | SnmpAdminString | read-create | Network Interface. Access: Instant. AC INI-Param: SIPInterface_NetworkInterface |
| ROW sipInterfaceRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| sipInterfaceSettings | 1.3.6.1.4.1.5003.9.10.3.1.1.27 | |||
| U32 sipInterfaceSRD | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.10 | Unsigned32 | read-create | Access: Instant. AC INI-Param: SIPInterface_SRD |
| sipInterfaceTable | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21 | not-accessible | GwApp SIP Interface Table | |
| U32 sipInterfaceTCPPort | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.8 | Unsigned32 | read-create | TCP Port number. Access: Instant. AC INI-Param: SIPInterface_TCPPort |
| U32 sipInterfaceTLSPort | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.9 | Unsigned32 | read-create | TLS Port number. Access: Instant. AC INI-Param: SIPInterface_TLSPort |
| U32 sipInterfaceUDPPort | 1.3.6.1.4.1.5003.9.10.3.1.1.27.21.1.7 | Unsigned32 | read-create | UDP Port number. Access: Instant. AC INI-Param: SIPInterface_UDPPort |
| sipMisc | 1.3.6.1.4.1.5003.9.10.3.1.2.7 | |||
| INT sipMisc3xxBehavior | 1.3.6.1.4.1.5003.9.10.3.1.2.7.31 | INTEGER | read-write | 3xx response behavior: Forwarding behavior - use different call identifiers Redirect behavior - use the same call identifiers: From, To & CallID. Access: Instant. AC INI-Param: 3XXBEHAVIOR |
| INT sipMiscAddTon2Rpi | 1.3.6.1.4.1.5003.9.10.3.1.2.7.10 | INTEGER | read-write | Add Number Type and Plan to Remote-Party-ID header. Access: Instant. AC INI-Param: ADDTON2RPI |
| U32 sipMiscApplicationProfile | 1.3.6.1.4.1.5003.9.10.3.1.2.7.43 | Unsigned32 | read-write | ApplicationProfile, read it later for validating that the board is theirs. Access: Offline. AC INI-Param: APPLICATIONPROFILE |
| INT sipMiscAssertedIDMode | 1.3.6.1.4.1.5003.9.10.3.1.2.7.8 | INTEGER | read-write | Select Asserted Identity header method. Access: Instant. AC INI-Param: ASSERTEDIDMODE |
| INT sipMiscComfortNoiseNegotiation | 1.3.6.1.4.1.5003.9.10.3.1.2.7.27 | INTEGER | read-write | is CN payload type is used and being negotiate. Access: Instant. AC INI-Param: COMFORTNOISENEGOTIATION |
| INT sipMiscDNSQueryType | 1.3.6.1.4.1.5003.9.10.3.1.2.7.24 | INTEGER | read-write | DNS Query Type: 0-ARecord, 1-SRV, 2-NAPTR . Has effect on every DNS query in the system. Access: Instant. AC INI-Param: DNSQUERYTYPE |
| INT sipMiscEnableCIC | 1.3.6.1.4.1.5003.9.10.3.1.2.7.11 | INTEGER | read-write | Enables CIC -> ISDN TNS IE interworking. Access: Instant. AC INI-Param: ENABLECIC |
| INT sipMiscEnableContactRestriction | 1.3.6.1.4.1.5003.9.10.3.1.2.7.40 | INTEGER | read-write | Hides the user part of the URI in the Contact Header 0 - Disable 1 - Enable. Access: Instant. AC INI-Param: ENABLECONTACTRESTRICTION |
| INT sipMiscEnableEarlyMedia | 1.3.6.1.4.1.5003.9.10.3.1.2.7.1 | INTEGER | read-write | Enable Early Media. Access: Instant. AC INI-Param: ENABLEEARLYMEDIA |
| INT sipMiscEnableGRUU | 1.3.6.1.4.1.5003.9.10.3.1.2.7.23 | INTEGER | read-write | Obtain and use GRUU (Global Routable UserAgentURIs). Access: Instant. AC INI-Param: ENABLEGRUU |
| INT sipMiscEnableHistoryInfo | 1.3.6.1.4.1.5003.9.10.3.1.2.7.25 | INTEGER | read-write | Enable History-Info header support. Access: Instant. AC INI-Param: ENABLEHISTORYINFO |
| INT sipMiscEnablePAssociatedURIHeader | 1.3.6.1.4.1.5003.9.10.3.1.2.7.41 | INTEGER | read-write | Handles the P-Associated-URI header in a 200OK response for a REGISTER request. Access: Instant. AC INI-Param: ENABLEPASSOCIATEDURIHEADER |
| INT sipMiscEnablePChargingVector | 1.3.6.1.4.1.5003.9.10.3.1.2.7.35 | INTEGER | read-write | Generate P-Charging-Vector header [0] - disabled [1] - enabled. Access: Instant. AC INI-Param: ENABLEPCHARGINGVECTOR |
| INT sipMiscEnableReasonHeader | 1.3.6.1.4.1.5003.9.10.3.1.2.7.30 | INTEGER | read-write | Enable Reason header in the outgoing messages. Access: Instant. AC INI-Param: ENABLEREASONHEADER |
| INT sipMiscEnableRpiHeader | 1.3.6.1.4.1.5003.9.10.3.1.2.7.6 | INTEGER | read-write | Enable Remote-Party-ID header. Access: Instant. AC INI-Param: ENABLERPIHEADER |
| INT sipMiscEnableSemiAttendedTransfer | 1.3.6.1.4.1.5003.9.10.3.1.2.7.32 | INTEGER | read-write | Semi-Attended Transfer when the session to the Target is not established. false - Use REFER with Replaces. true - Use CANCEL and REFER without Replaces if session is not established. Access: Instant. AC INI-Param: ENABLESEMIATTENDEDTRANSFER |
| INT sipMiscEnableSIPS | 1.3.6.1.4.1.5003.9.10.3.1.2.7.16 | INTEGER | read-write | Enable SIP secured URI usage. Access: Instant. AC INI-Param: ENABLESIPS |
| INT sipMiscEnableSRVQuery | 1.3.6.1.4.1.5003.9.10.3.1.2.7.17 | INTEGER | read-write | Enable DNS SRV queries. Access: Instant. AC INI-Param: ENABLESRVQUERY |
| INT sipMiscEnableTCPConnectionReuse | 1.3.6.1.4.1.5003.9.10.3.1.2.7.26 | INTEGER | read-write | Enable reuse of TCP connection. Access: Instant. AC INI-Param: ENABLETCPCONNECTIONREUSE |
| INT sipMiscEnableVMURI | 1.3.6.1.4.1.5003.9.10.3.1.2.7.34 | INTEGER | read-write | Enable History-Info header support. Access: Instant. AC INI-Param: ENABLEVMURI |
| INT sipMiscForkingHandlingMode | 1.3.6.1.4.1.5003.9.10.3.1.2.7.46 | INTEGER | read-write | Decides the handling method to 18X response to forking 0 - Parallel handling - only the first 18X response is handled 1 - Sequential handling - all the 18X responses are handled. Access: Instant. AC INI-Param: FORKINGHANDLINGMODE |
| STR sipMiscGatewayName | 1.3.6.1.4.1.5003.9.10.3.1.2.7.4 | SnmpAdminString | read-write | Gateway name. Access: Instant. AC INI-Param: SIPGATEWAYNAME |
| U32 sipMiscISubNumberOfDigits | 1.3.6.1.4.1.5003.9.10.3.1.2.7.13 | Unsigned32 | read-write | Number of digits that will be taken from end of phone number as Subaddress. Access: Instant. AC INI-Param: ISUBNUMBEROFDIGITS |
| INT sipMiscIsUserPhone | 1.3.6.1.4.1.5003.9.10.3.1.2.7.3 | INTEGER | read-write | Add User=Phone parameter to SIP URL. Access: Instant. AC INI-Param: ISUSERPHONE |
| INT sipMiscIsUserPhoneInFrom | 1.3.6.1.4.1.5003.9.10.3.1.2.7.9 | INTEGER | read-write | Add 'User=Phone' to From header. Access: Instant. AC INI-Param: ISUSERPHONEINFROM |
| U32 sipMiscMinSE | 1.3.6.1.4.1.5003.9.10.3.1.2.7.42 | Unsigned32 | read-write | Minimal value for session refresh. Access: Instant. AC INI-Param: MINSE |
| INT sipMiscMultiPtimeFormat | 1.3.6.1.4.1.5003.9.10.3.1.2.7.28 | INTEGER | read-write | Format of multiple ptime (ptime per coder) in outgoing SDP. Access: Instant. AC INI-Param: MULTIPTIMEFORMAT |
| INT sipMiscOfferUnencryptedSRTCP | 1.3.6.1.4.1.5003.9.10.3.1.2.7.47 | INTEGER | read-write | If set to 1, the 'crypto' attribute includes the UNENCRYPTED_SRTCP parameter. If set to 1, the UNENCRYPTED_SRTCP parameter is not included. Access: Instant. AC INI-Param: OFFERUNENCRYPTEDSRTCP |
| STR sipMiscOPTIONSUserPart | 1.3.6.1.4.1.5003.9.10.3.1.2.7.44 | SnmpAdminString | read-write | Allow to configure the OPTIONS userpart string for all gateways. The default value should be empty string which means that we don't use this parameter. Another special value is 'empty' which means that the we don't populate the user part of the OPTIONS request URI. Any other value will be taken as is and used as the user part of the OPTIONS request URI. Access: Instant. AC INI-Param: OPTIONSUSERPART |
| STR sipMiscPAssertedUserName | 1.3.6.1.4.1.5003.9.10.3.1.2.7.36 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on Do Not Disturb (PBX to VoiceMail). Access: Instant. AC INI-Param: PASSERTEDUSERNAME |
| INT sipMiscPrackMode | 1.3.6.1.4.1.5003.9.10.3.1.2.7.5 | INTEGER | read-write | PRACK mechanism mode for 1XX reliable responses: 0- Disabled , 1- Supported , 2- Required. Access: Instant. AC INI-Param: PrackMode |
| INT sipMiscResetOnINIFileDownload | 1.3.6.1.4.1.5003.9.10.3.1.2.7.38 | INTEGER | read-write | Determine if Reset after INI File Download is execute. Access: Instant. AC INI-Param: ResetOnINIFileDownload |
| INT sipMiscRTPOnlyMode | 1.3.6.1.4.1.5003.9.10.3.1.2.7.29 | INTEGER | read-write | On RTP only mode their is no signalling protocol (for media parameters negotiation with the remote side). The channel is open immediately. The IP for the media is taken from the routing table. The RTP ports are corresponding to the local side ports. RTP-Only mode Values: 0 - regular call establishment 1 - No Signalling. The RTP channel open for Rx & Tx 2- No Signalling. The RTP channel open only for Tx 3 - No Signalling. The RTP channel open only for Rx. Access: Instant. AC INI-Param: RTPONLYMODE |
| STR sipMiscSDPSessionOwner | 1.3.6.1.4.1.5003.9.10.3.1.2.7.37 | SnmpAdminString | read-write | The SDP owner string. Access: Instant. AC INI-Param: SIPSDPSESSIONOWNER |
| INT sipMiscSend180ForCallWaiting | 1.3.6.1.4.1.5003.9.10.3.1.2.7.20 | INTEGER | read-write | Send 180 for call waiting. Used for parties that do not support 182. Access: Instant. AC INI-Param: SEND180FORCALLWAITING |
| INT sipMiscSessionExpiresMethod | 1.3.6.1.4.1.5003.9.10.3.1.2.7.22 | INTEGER | read-write | Determines the Method which the SIP session will be using to referesh the session. Access: Instant. AC INI-Param: SESSIONEXPIRESMETHOD |
| U32 sipMiscSetDefaultOnIniFileProcess | 1.3.6.1.4.1.5003.9.10.3.1.2.7.39 | Unsigned32 | read-write | Determine if all parameters are set to their defaults before processing updated INI File. Access: Instant. AC INI-Param: SetDefaultOnIniFileProcess |
| INT sipMiscSIP183Behaviour | 1.3.6.1.4.1.5003.9.10.3.1.2.7.14 | INTEGER | read-write | If this parameter set to 1, ALERT to ISDN will be sent upon 183 receive. Access: Instant. AC INI-Param: SIP183BEHAVIOUR |
| U32 sipMiscSipSessionExpires | 1.3.6.1.4.1.5003.9.10.3.1.2.7.2 | Unsigned32 | read-write | The SIP session will be refreshed (using INVITE) each time this timer expires (seconds). Access: Instant. AC INI-Param: SIPSESSIONEXPIRES |
| STR sipMiscSourceNumberPreference | 1.3.6.1.4.1.5003.9.10.3.1.2.7.48 | SnmpAdminString | read-write | Determines from where the source number shall be taken from (in an incoming INVITE request). Parameter values: - NULL: no changes in current logic - FROM: source number is taken from 'FROM' field. Access: Instant. AC INI-Param: SOURCENUMBERPREFERENCE |
| STR sipMiscSubject | 1.3.6.1.4.1.5003.9.10.3.1.2.7.18 | SnmpAdminString | read-write | User-defined sip subject. Access: Instant. AC INI-Param: SIPSUBJECT |
| INT sipMiscTransportType | 1.3.6.1.4.1.5003.9.10.3.1.2.7.12 | INTEGER | read-write | SIP transport type. Access: Instant. AC INI-Param: SIPTRANSPORTTYPE |
| INT sipMiscUseAORInReferToHeader | 1.3.6.1.4.1.5003.9.10.3.1.2.7.45 | INTEGER | read-write | If enabled, we will use URI from To/From headers in Refer-To header. If disabled, we will take the URI from Contact. Access: Instant. AC INI-Param: USEAORINREFERTOHEADER |
| STR sipMiscUserAgentDisplayInfo | 1.3.6.1.4.1.5003.9.10.3.1.2.7.21 | SnmpAdminString | read-write | String that will be displayed in the SIP Header 'User-Agent' or 'Server'. Access: Instant. AC INI-Param: USERAGENTDISPLAYINFO |
| INT sipMiscUseSIPTgrp | 1.3.6.1.4.1.5003.9.10.3.1.2.7.19 | INTEGER | read-write | Use TGRP parameter 0 - disable [Default] , 1 - send only , 2 - send and use if in the RequestURI when receiving INVITE, 3 - Nortel Hotline. Access: Instant. AC INI-Param: USESIPTGRP |
| INT sipMiscUseSIPURIForDiversionHeader | 1.3.6.1.4.1.5003.9.10.3.1.2.7.33 | INTEGER | read-write | Use Tel uri or Sip uri for Diversion header. Access: Instant. AC INI-Param: UseSIPURIForDiversionHeader |
| INT sipMiscUseToHeaderAsCalledNum | 1.3.6.1.4.1.5003.9.10.3.1.2.7.15 | INTEGER | read-write | Use the user part of To header URL as called number (IP->TEL). Access: Instant. AC INI-Param: ISUSETOHEADERASCALLEDNUMBER |
| INT sipMiscXChannelHeader | 1.3.6.1.4.1.5003.9.10.3.1.2.7.7 | INTEGER | read-write | 0 (default): No special header 1:Add special header for trunk and B-Channel. Access: Instant. AC INI-Param: XCHANNELHEADER |
| sipPorts | 1.3.6.1.4.1.5003.9.10.3.1.2.3 | |||
| U32 sipPortsDestinationPort | 1.3.6.1.4.1.5003.9.10.3.1.2.3.1 | Unsigned32 | read-write | Default SIP destination port (usually 5060). Access: Instant. AC INI-Param: SIPDESTINATIONPORT |
| U32 sipPortsLocalSipPort | 1.3.6.1.4.1.5003.9.10.3.1.2.3.2 | Unsigned32 | read-write | Local SIP port used for signaling. Access: Instant. AC INI-Param: LOCALSIPPORT |
| U32 sipPortsTCPLocalSipPort | 1.3.6.1.4.1.5003.9.10.3.1.2.3.3 | Unsigned32 | read-write | Local SIP port used for signaling. Access: Instant. AC INI-Param: TCPLOCALSIPPORT |
| U32 sipPortsTLSLocalSipPort | 1.3.6.1.4.1.5003.9.10.3.1.2.3.4 | Unsigned32 | read-write | Local TLS SIP port used for signaling. Access: Instant. AC INI-Param: TLSLOCALSIPPORT |
| sipProxy | 1.3.6.1.4.1.5003.9.10.3.1.2.1 | |||
| INT sipProxyAlwaysSendToProxy | 1.3.6.1.4.1.5003.9.10.3.1.2.1.8 | INTEGER | read-write | Send all messages to Proxy server. Access: Instant. AC INI-Param: ALWAYSSENDTOPROXY |
| INT sipProxyAlwaysUseRouteTable | 1.3.6.1.4.1.5003.9.10.3.1.2.1.7 | INTEGER | read-write | Always use routing table even though proxy is available. Access: Instant. AC INI-Param: ALWAYSUSEROUTETABLE |
| INT sipProxyDNSQueryType | 1.3.6.1.4.1.5003.9.10.3.1.2.1.15 | INTEGER | read-write | DNS Query Type: 0-ARecord, 1-SRV, 2-NAPTR . Has effect on every DNS query in the system. Access: Instant. AC INI-Param: DNSQUERYTYPE |
| INT sipProxyEnableKeepAlive | 1.3.6.1.4.1.5003.9.10.3.1.2.1.2 | INTEGER | read-write | Enable Proxy Keep-Alive over OPTIONS method or REGISTER method. Access: Instant. AC INI-Param: ENABLEPROXYKEEPALIVE |
| INT sipProxyEnableSRVQuery | 1.3.6.1.4.1.5003.9.10.3.1.2.1.14 | INTEGER | read-write | Enable DNS SRV queries for Proxy domain name. Access: Instant. AC INI-Param: ENABLEPROXYSRVQUERY |
| U32 sipProxyHotSwapRtx | 1.3.6.1.4.1.5003.9.10.3.1.2.1.5 | Unsigned32 | read-write | Number of Rtx before Hotswap is performed. Access: Instant. AC INI-Param: PROXYHOTSWAPRTX |
| U32 sipProxyIPListRefreshTime | 1.3.6.1.4.1.5003.9.10.3.1.2.1.17 | Unsigned32 | read-write | Time interval between refresh of proxies list (seconds). For example SRV query will be done every ProxyIPListRefreshTime seconds. Access: Instant. AC INI-Param: PROXYIPLISTREFRESHTIME |
| INT sipProxyIsFallbackUsed | 1.3.6.1.4.1.5003.9.10.3.1.2.1.10 | INTEGER | read-write | Allow fallback to internal Tel to IP routing table if Proxy is not responding. Access: Instant. AC INI-Param: IsFallbackUsed |
| INT sipProxyIsHotSwap | 1.3.6.1.4.1.5003.9.10.3.1.2.1.4 | INTEGER | read-write | Enable Proxy Hot-Swap mode. Access: Instant. AC INI-Param: ISPROXYHOTSWAP |
| INT sipProxyIsTrustedProxy | 1.3.6.1.4.1.5003.9.10.3.1.2.1.12 | INTEGER | read-write | Determine whether the proxy is a trusted node. Access: Instant. AC INI-Param: ISTRUSTEDPROXY |
| U32 sipProxyKeepAliveTime | 1.3.6.1.4.1.5003.9.10.3.1.2.1.9 | Unsigned32 | read-write | Time interval between Proxy Keep-Alive messages (seconds). Access: Instant. AC INI-Param: ProxyKeepAliveTime |
| INT sipProxyLoadBalancingMethod | 1.3.6.1.4.1.5003.9.10.3.1.2.1.16 | INTEGER | read-write | Method of the proxies load balancing: 0 - Disabled (default) 1 - RoundRobin 2 - Random SRV Weights. Access: Instant. AC INI-Param: PROXYLOADBALANCINGMETHOD |
| STR sipProxyName | 1.3.6.1.4.1.5003.9.10.3.1.2.1.3 | SnmpAdminString | read-write | SIP Proxy name. Access: Instant. AC INI-Param: PROXYNAME |
| INT sipProxyRedundancyMode | 1.3.6.1.4.1.5003.9.10.3.1.2.1.6 | INTEGER | read-write | Redundancy Mode - Parking on active proxy or switching to main Proxy whenever online. Access: Instant. AC INI-Param: PROXYREDUNDANCYMODE |
| INT sipProxySendInviteToProxy | 1.3.6.1.4.1.5003.9.10.3.1.2.1.11 | INTEGER | read-write | Always send INVITE messages to Proxy server. Access: Instant. AC INI-Param: SENDINVITETOPROXY |
| INT sipProxySetAction | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sipProxySetActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sipProxySetEnableProxyKeepAlive | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.5 | INTEGER | read-create | GwApp Proxy Set Table. Access: Instant. AC INI-Param: ProxySet_EnableProxyKeepAlive |
| sipProxySetEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1 | not-accessible | ||
| U32 sipProxySetIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.1 | Unsigned32 | not-accessible | AC INI-Param: ProxySet_Index |
| INT sipProxySetIsProxyHotSwap | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.8 | INTEGER | read-create | GwApp Proxy Set Table. Access: Instant. AC INI-Param: ProxySet_IsProxyHotSwap |
| U32 sipProxySetProxyKeepAliveTime | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.6 | Unsigned32 | read-create | GwApp Proxy Set Table. Access: Instant. AC INI-Param: ProxySet_ProxyKeepAliveTime |
| INT sipProxySetProxyLoadBalancingMethod | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.7 | INTEGER | read-create | GwApp Proxy Set Table. Access: Instant. AC INI-Param: ProxySet_ProxyLoadBalancingMethod |
| ROW sipProxySetRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| sipProxySetTable | 1.3.6.1.4.1.5003.9.10.3.1.2.1.22 | not-accessible | GwApp Proxy Set Table | |
| INT sipProxyUsed | 1.3.6.1.4.1.5003.9.10.3.1.2.1.1 | INTEGER | read-write | Is SIP Proxy used. Access: Instant. AC INI-Param: ISPROXYUSED |
| INT sipProxyUseGatewayNameForOptions | 1.3.6.1.4.1.5003.9.10.3.1.2.1.13 | INTEGER | read-write | Use Gateway name (instead of IP address) in Keep-Alive OPTIONS messages. Access: Instant. AC INI-Param: USEGATEWAYNAMEFOROPTIONS |
| sipRegistration | 1.3.6.1.4.1.5003.9.10.3.1.2.6 | |||
| STR sipRegistrationIP | 1.3.6.1.4.1.5003.9.10.3.1.2.6.2 | SnmpAdminString | read-write | SIP Registrar IP address. Access: Instant. AC INI-Param: REGISTRARIP |
| INT sipRegistrationIsNeeded | 1.3.6.1.4.1.5003.9.10.3.1.2.6.1 | INTEGER | read-write | Is Proxy registration necessary. Access: Instant. AC INI-Param: ISREGISTERNEEDED |
| STR sipRegistrationName | 1.3.6.1.4.1.5003.9.10.3.1.2.6.7 | SnmpAdminString | read-write | Gateway registration name. Access: Instant. AC INI-Param: GWREGISTRATIONNAME |
| INT sipRegistrationRegisterOnInviteFailure | 1.3.6.1.4.1.5003.9.10.3.1.2.6.8 | INTEGER | read-write | Enable ReRegister upon INVITE transaction failure. Access: Instant. AC INI-Param: REGISTERONINVITEFAILURE |
| STR sipRegistrationRegistrarName | 1.3.6.1.4.1.5003.9.10.3.1.2.6.5 | SnmpAdminString | read-write | SIP Registrar name. Access: Instant. AC INI-Param: REGISTRARNAME |
| INT sipRegistrationRegistrarTransportType | 1.3.6.1.4.1.5003.9.10.3.1.2.6.10 | INTEGER | read-write | Registrar transport type. Access: Instant. AC INI-Param: REGISTRARTRANSPORTTYPE |
| U32 sipRegistrationRegistrationRetryTime | 1.3.6.1.4.1.5003.9.10.3.1.2.6.4 | Unsigned32 | read-write | Time in which the gateway will try to register after last registration failure (seconds). Access: Instant. AC INI-Param: REGISTRATIONRETRYTIME |
| INT sipRegistrationReRegisterOnConnectionFailure | 1.3.6.1.4.1.5003.9.10.3.1.2.6.11 | INTEGER | read-write | Enables GW to perform Re-Registeration on TCP/TLS connection failure. Access: Instant. AC INI-Param: REREGISTERONCONNECTIONFAILURE |
| U32 sipRegistrationTime | 1.3.6.1.4.1.5003.9.10.3.1.2.6.3 | Unsigned32 | read-write | Time for which registration to Gatekeeper/Proxy is valid. Causes periodic registration (seconds). Access: Instant. AC INI-Param: RegistrationTime |
| U32 sipRegistrationTimeDivider | 1.3.6.1.4.1.5003.9.10.3.1.2.6.6 | Unsigned32 | read-write | Percentage of RegistrationTime when the actual new REGISTER request will be sent out. Access: Instant. AC INI-Param: REGISTRATIONTIMEDIVIDER |
| U32 sipRegistrationTimeThreshold | 1.3.6.1.4.1.5003.9.10.3.1.2.6.9 | Unsigned32 | read-write | If (REGISTRATIONTIMETHRESHOLD > 0) and (REGISTRATIONTIMETHRESHOLD < computed registration time using existing logic) then new registration time will be (Registration time from expires header � REGISTRATIONTIMETHRESHOLD). Access: Instant. AC INI-Param: REGISTRATIONTIMETHRESHOLD |
| sipRetransmission | 1.3.6.1.4.1.5003.9.10.3.1.2.5 | |||
| INT sipRetransmissionEnablePTime | 1.3.6.1.4.1.5003.9.10.3.1.2.5.5 | INTEGER | read-write | is ptime parameter needed in sdp. Access: Instant. AC INI-Param: ENABLEPTIME |
| INT sipRetransmissionIsRtxEnable | 1.3.6.1.4.1.5003.9.10.3.1.2.5.4 | INTEGER | read-write | is Rtx timer enabled. Access: Instant. AC INI-Param: ISRTXENABLE |
| U32 sipRetransmissionRetryAfterTime | 1.3.6.1.4.1.5003.9.10.3.1.2.5.7 | Unsigned32 | read-write | Retry After time for the proxy to be in state Unavailable. Access: Instant. AC INI-Param: RETRYAFTERTIME |
| U32 sipRetransmissionSipMaxRtx | 1.3.6.1.4.1.5003.9.10.3.1.2.5.3 | Unsigned32 | read-write | Maximum number of retransmissions. Access: Instant. AC INI-Param: SipMaxRtx |
| U32 sipRetransmissionT1Rtx | 1.3.6.1.4.1.5003.9.10.3.1.2.5.1 | Unsigned32 | read-write | SIP T1 timeout for retransmission. Access: Instant. AC INI-Param: SIPT1RTX |
| U32 sipRetransmissionT2Rtx | 1.3.6.1.4.1.5003.9.10.3.1.2.5.2 | Unsigned32 | read-write | SIP T2 timeout for retransmission. Access: Instant. AC INI-Param: SIPT2RTX |
| U32 sipRetransmissionTCPTimeout | 1.3.6.1.4.1.5003.9.10.3.1.2.5.6 | Unsigned32 | read-write | SIP TCP time out (influence timerB and Timer F). Access: Instant. AC INI-Param: SIPTCPTIMEOUT |
| sipSAS | 1.3.6.1.4.1.5003.9.10.3.1.2.10 | |||
| INT sipSASBindingMode | 1.3.6.1.4.1.5003.9.10.3.1.2.10.10 | INTEGER | read-write | Defines the SAS database binding mode: 0 - URI dependant 1 - according to user part. Access: Instant. AC INI-Param: SASBINDINGMODE |
| STR sipSASDefaultGatewayIP | 1.3.6.1.4.1.5003.9.10.3.1.2.10.3 | SnmpAdminString | read-write | SIP SAS default IP address for incoming requests in emergency mode. Access: Instant. AC INI-Param: SASDEFAULTGATEWAYIP |
| INT sipSASEnable | 1.3.6.1.4.1.5003.9.10.3.1.2.10.1 | INTEGER | read-write | Enables SAS functionality. Access: Offline. AC INI-Param: ENABLESAS |
| INT sipSASEnableENUM | 1.3.6.1.4.1.5003.9.10.3.1.2.10.12 | INTEGER | read-write | Enables SAS to perform ENUM query when receiving INVITE messages in emergency mode. Access: Instant. AC INI-Param: SASENABLEENUM |
| INT sipSASEnableRecordRoute | 1.3.6.1.4.1.5003.9.10.3.1.2.10.13 | INTEGER | read-write | Enables SAS to add record-Route header to requests. Access: Instant. AC INI-Param: SASENABLERECORDROUTE |
| U32 sipSASLocalSIPTcpPort | 1.3.6.1.4.1.5003.9.10.3.1.2.10.7 | Unsigned32 | read-write | Local SAS SIP port used for signaling over TCP. Access: Instant. AC INI-Param: SASLOCALSIPTCPPORT |
| U32 sipSASLocalSIPTlsPort | 1.3.6.1.4.1.5003.9.10.3.1.2.10.4 | Unsigned32 | read-write | Local SAS SIP port used for signaling over TLS. Access: Instant. AC INI-Param: SASLOCALSIPTLSPORT |
| U32 sipSASLocalSIPUdpPort | 1.3.6.1.4.1.5003.9.10.3.1.2.10.2 | Unsigned32 | read-write | Local SAS SIP port used for signaling over UDP. Access: Instant. AC INI-Param: SASLOCALSIPUDPPORT |
| U32 sipSASProxySet | 1.3.6.1.4.1.5003.9.10.3.1.2.10.8 | Unsigned32 | read-write | Proxy Set Id for SAS. Access: Instant. AC INI-Param: SASPROXYSET |
| I32 sipSASRedundantProxySet | 1.3.6.1.4.1.5003.9.10.3.1.2.10.9 | Integer32 | read-write | Proxy Set Id for Redundant SAS. Access: Instant. AC INI-Param: REDUNDANTSASPROXYSET |
| U32 sipSASRegistrationTime | 1.3.6.1.4.1.5003.9.10.3.1.2.10.5 | Unsigned32 | read-write | SAS will send this value in expires header while working in emergency mode. Access: Instant. AC INI-Param: SASREGISTRATIONTIME |
| U32 sipSASShortNumberLength | 1.3.6.1.4.1.5003.9.10.3.1.2.10.6 | Unsigned32 | read-write | Upon incoming request the user info in the request is compared to the registered one. SAS performs comparison of the arrived user info with the suffix of the registered one. The length of the suffix is determined by this parameter. Access: Instant. AC INI-Param: SASSHORTNUMBERLENGTH |
| INT sipSASSurvivabilityMode | 1.3.6.1.4.1.5003.9.10.3.1.2.10.11 | INTEGER | read-write | Defines the SAS working mode: 0 � Standard Mode (working with configured proxy set) 1 � Always emergency mode (working without proxy) 2 � Ignore REGISTER in normal mode. Access: Instant. AC INI-Param: SASSURVIVABILITYMODE |
| sipSubscribe | 1.3.6.1.4.1.5003.9.10.3.1.2.8 | |||
| INT sipSubscribeEnable | 1.3.6.1.4.1.5003.9.10.3.1.2.8.1 | INTEGER | read-write | This parameter related to Subscribe/UnSubscribe buttons. Access: Instant. AC INI-Param: SHOULDSUBSCRIBE |
| INT sipSubscribeEnableMWISubscription | 1.3.6.1.4.1.5003.9.10.3.1.2.8.3 | INTEGER | read-write | Enable subscription for Message Waiting Indicator service. Access: Instant. AC INI-Param: ENABLEMWISUBSCRIPTION |
| U32 sipSubscribeRetryTime | 1.3.6.1.4.1.5003.9.10.3.1.2.8.2 | Unsigned32 | read-write | MWI service subscription retry time after last subscription failure (seconds). Access: Instant. AC INI-Param: SUBSCRIBERETRYTIME |
| INT sipSubscribeSubscriptionMode | 1.3.6.1.4.1.5003.9.10.3.1.2.8.4 | INTEGER | read-write | Subscription Mode: 0 - Per Endpoint, 1 - Per Gateway. Access: Instant. AC INI-Param: SUBSCRIPTIONMODE |
| INT sipTxDTMFOptionAction | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT sipTxDTMFOptionActionResult | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| sipTxDTMFOptionEntry | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21.1 | not-accessible | ||
| U32 sipTxDTMFOptionIndex | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: TxDtmfOption_Index |
| ROW sipTxDTMFOptionRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| sipTxDTMFOptionTable | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21 | not-accessible | The names of the five possible coders. | |
| INT sipTxDTMFOptionValue | 1.3.6.1.4.1.5003.9.10.3.1.2.2.21.1.5 | INTEGER | read-create | Transmit DTMF option. Access: Instant. AC INI-Param: TxDtmfOption_Type |
| INT srcIP2TELAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT srcIP2TELActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR srcIP2TELDestPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.11 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_DestinationPrefix |
| srcIP2TELEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1 | not-accessible | ||
| U32 srcIP2TELIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.1 | Unsigned32 | not-accessible | Source number, starting at 0. AC INI-Param: SourceNumberMapIp2Tel_Index |
| INT srcIP2TELNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.9 | INTEGER | read-create | Number Plan. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_NumberPlan |
| INT srcIP2TELNumberType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.10 | INTEGER | read-create | Number Type. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_NumberType |
| U32 srcIP2TELNumOfDigitsToLeave | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.8 | Unsigned32 | read-create | Number of digits to leave. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_LeaveFromRight |
| U32 srcIP2TELNumOfDigitsToRemFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.13 | Unsigned32 | read-create | Num Of digits To Remove from Right. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_RemoveFromRight |
| U32 srcIP2TELNumOfStrippedDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.6 | Unsigned32 | read-create | Num of stripped digits. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_RemoveFromLeft |
| STR srcIP2TELPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_SourcePrefix |
| STR srcIP2TELPrefixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.7 | SnmpAdminString | read-create | Prefix to Add. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_Prefix2Add |
| INT srcIP2TELPresentation | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.12 | INTEGER | read-create | Presentation. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_IsPresentationRestricted |
| ROW srcIP2TELRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR srcIP2TELSourceIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.15 | SnmpAdminString | read-create | Source Address. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_SourceAddress |
| STR srcIP2TELSuffix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23.1.14 | SnmpAdminString | read-create | Suffix To Add. Access: Instant. AC INI-Param: SourceNumberMapIp2Tel_Suffix2Add |
| srcIP2TELTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.23 | not-accessible | ||
| INT srcTEL2IPAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT srcTEL2IPActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR srcTEL2IPDestPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.11 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_DestinationPrefix |
| srcTEL2IPEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1 | not-accessible | ||
| U32 srcTEL2IPIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.1 | Unsigned32 | not-accessible | Source number, starting at 0. AC INI-Param: SourceNumberMapTel2Ip_Index |
| INT srcTEL2IPNumberPlan | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.9 | INTEGER | read-create | Number Plan. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_NumberPlan |
| INT srcTEL2IPNumberType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.10 | INTEGER | read-create | Number Type. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_NumberType |
| U32 srcTEL2IPNumOfDigitsToLeave | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.8 | Unsigned32 | read-create | Number of digits to leave. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_LeaveFromRight |
| U32 srcTEL2IPNumOfDigitsToRemFromRight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.13 | Unsigned32 | read-create | Num Of digits To Remove from Right. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_RemoveFromRight |
| U32 srcTEL2IPNumOfStrippedDigits | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.6 | Unsigned32 | read-create | Num of stripped digits, Remove from left. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_RemoveFromLeft |
| STR srcTEL2IPPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.5 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_SourcePrefix |
| STR srcTEL2IPPrefixToAdd | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.7 | SnmpAdminString | read-create | Prefix to Add. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_Prefix2Add |
| INT srcTEL2IPPresentation | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.12 | INTEGER | read-create | Presentation. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_IsPresentationRestricted |
| ROW srcTEL2IPRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR srcTEL2IPSourceIPAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.15 | SnmpAdminString | read-create | Source Address. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_SourceAddress |
| I32 srcTEL2IPSourceIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.17 | Integer32 | read-create | GwApp IP-toTel Destination Phone Number Manipulation Rules Table. Access: Instant. AC INI-Param: NumberMapIp2Tel_SrcIPGroupID |
| I32 srcTEL2IPSourceTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.16 | Integer32 | read-create | GwApp IP-toTel Destination Phone Number Manipulation Rules Table. Access: Instant. AC INI-Param: NumberMapIp2Tel_SrcTrunkGroupID |
| STR srcTEL2IPSuffix2Add | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24.1.14 | SnmpAdminString | read-create | Suffix To Add. Access: Instant. AC INI-Param: SourceNumberMapTel2Ip_Suffix2Add |
| srcTEL2IPTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.21.24 | not-accessible | ||
| INT srdAction | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT srdActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT srdBlockUnRegUsers | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.8 | INTEGER | read-create | Block Calls From Unregistered User. Access: Offline. AC INI-Param: SRD_BlockUnRegUsers |
| srdEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1 | not-accessible | ||
| U32 srdIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.1 | Unsigned32 | read-only | . AC INI-Param: SRD_Index |
| INT srdIntraSRDMediaAnchoring | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.7 | INTEGER | read-create | Internal SRD Media Anchoring. Access: Offline. AC INI-Param: SRD_IntraSRDMediaAnchoring |
| I32 srdMaxNumOfRegUsers | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.9 | Integer32 | read-create | Max Number Of Registered Users. MP1xx - 25 M1K - 200 M2K- 250 M3K - 3000. Access: Offline. AC INI-Param: SRD_MaxNumOfRegUsers |
| STR srdMediaRealm | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.6 | SnmpAdminString | read-create | GwApp Signaling Routing Domain media realm. Access: Instant. AC INI-Param: SRD_MediaRealm |
| STR srdName | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.5 | SnmpAdminString | read-create | GwApp Signaling Routing Domain name. Access: Instant. AC INI-Param: SRD_Name |
| ROW srdRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| srdSettings | 1.3.6.1.4.1.5003.9.10.3.1.1.26 | |||
| srdTable | 1.3.6.1.4.1.5003.9.10.3.1.1.26.21 | not-accessible | GwApp Signaling Routing Domain (SRD) Table | |
| INT srvInfoAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT srvInfoActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.5 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR srvInfoDNSName | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.8 | SnmpAdminString | read-create | the DNS in the SRV Query Result. Access: Instant. AC INI-Param: Srv2Ip_Dns1 |
| STR srvInfoDNSName2 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.12 | SnmpAdminString | read-create | the DNS in the SRV Query Result. Access: Instant. AC INI-Param: Srv2Ip_Dns2 |
| STR srvInfoDNSName3 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.16 | SnmpAdminString | read-create | the DNS in the SRV Query Result. Access: Instant. AC INI-Param: Srv2Ip_Dns3 |
| srvInfoEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1 | not-accessible | ||
| U32 srvInfoIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: Srv2Ip_Index |
| STR srvInfoInternalDomainName | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.6 | SnmpAdminString | read-create | the Domain name for the SRV query. Access: Instant. AC INI-Param: Srv2Ip_InternalDomain |
| U32 srvInfoPort | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.11 | Unsigned32 | read-create | the port of the DNS. Access: Instant. AC INI-Param: Srv2Ip_Port1 |
| U32 srvInfoPort2 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.15 | Unsigned32 | read-create | the port of the DNS. Access: Instant. AC INI-Param: Srv2Ip_Port2 |
| U32 srvInfoPort3 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.19 | Unsigned32 | read-create | the port of the DNS. Access: Instant. AC INI-Param: Srv2Ip_Port3 |
| U32 srvInfoPriority | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.9 | Unsigned32 | read-create | the Priority of this SRV Query. Access: Instant. AC INI-Param: Srv2Ip_Priority1 |
| U32 srvInfoPriority2 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.13 | Unsigned32 | read-create | the Priority of this SRV Query. Access: Instant. AC INI-Param: Srv2Ip_Priority2 |
| U32 srvInfoPriority3 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.17 | Unsigned32 | read-create | the Priority of this SRV Query. Access: Instant. AC INI-Param: Srv2Ip_Priority3 |
| U32 srvInfoRecordNum | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.2 | Unsigned32 | not-accessible | Equals to the entry number. AC INI-Param: Srv2Ip_Index |
| ROW srvInfoRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.3 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| srvInfoTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4 | not-accessible | ||
| INT srvInfoTransportType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.7 | INTEGER | read-create | the transport type. Access: Instant. AC INI-Param: Srv2Ip_TransportType |
| U32 srvInfoWeight | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.10 | Unsigned32 | read-create | the Weight of this SRV Query. Access: Instant. AC INI-Param: Srv2Ip_Weight1 |
| U32 srvInfoWeight2 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.14 | Unsigned32 | read-create | the Weight of this SRV Query. Access: Instant. AC INI-Param: Srv2Ip_Weight2 |
| U32 srvInfoWeight3 | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.4.1.18 | Unsigned32 | read-create | the Weight of this SRV Query. Access: Instant. AC INI-Param: Srv2Ip_Weight3 |
| streaming | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10 | |||
| STR streamingID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.1 | SnmpAdminString | read-write | Identification of HTTP played voice prompt (To be used by SIP INVITE). Access: Instant. AC INI-Param: STREAMINGID |
| STR streamingMediaID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.4 | SnmpAdminString | read-write | Identification of HTTP played voice prompt (To be used by SIP INVITE). Access: Instant. AC INI-Param: MediaStreamingID |
| STR streamingMonitorID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.10 | SnmpAdminString | read-write | Identification of Calea call (To be used by SIP INVITE). Access: Instant. AC INI-Param: MONITORID |
| STR streamingMscmlID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.9 | SnmpAdminString | read-write | Identification of HTTP played voice prompt using mscml(To be used by SIP INVITE). Access: Instant. AC INI-Param: MSCMLID |
| STR streamingNetAnnAnncID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.8 | SnmpAdminString | read-write | NetAnn Announcement ID. Access: Instant. AC INI-Param: NETANNANNCID |
| U32 streamingNumOfEndPoints | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.2 | Unsigned32 | read-write | Number of Streaming endpoints. Access: Offline. AC INI-Param: NUMOFSTREAMINGENDPOINTS |
| STR streamingPlayFromID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.6 | SnmpAdminString | read-write | Identification of voice stream play location (To be used by SIP INVITE). Access: Instant. AC INI-Param: PLAYFROMID |
| STR streamingRecordScriptPath | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.3 | SnmpAdminString | read-write | Identification of HTTP Record Script (To be used by FOR RECORD). Access: Offline. AC INI-Param: RecordScriptPath |
| STR streamingRecordToID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.7 | SnmpAdminString | read-write | Identification of voice stream recording location (To be used by SIP INVITE). Access: Instant. AC INI-Param: RECORDTOID |
| I32 streamingStopRecordingOnNoSpeachTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.5.11.10.5 | Integer32 | read-write | Timeout for no speech detection used to stop recording. Access: Instant. AC INI-Param: STOPRECORDINGONNOSPEACHTIMEOUT |
| supServices | 1.3.6.1.4.1.5003.9.10.3.1.1.7 | |||
| U32 supServicesBlindTransferDisconnectTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.7.30 | Unsigned32 | read-write | Maximum time (milliseconds) to wait for disconnect from tel before performing blind transfer. Access: Instant. AC INI-Param: BLINDTRANSFERDISCONNECTTIMEOUT |
| U32 supServicesCHRRTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.7.7 | Unsigned32 | read-write | Call hold reminder ring maximum ringing time (in seconds). Access: Instant. AC INI-Param: CHRRTIMEOUT |
| supServicesConference | 1.3.6.1.4.1.5003.9.10.3.1.1.7.14 | |||
| INT supServicesConferenceEnable3Way | 1.3.6.1.4.1.5003.9.10.3.1.1.7.14.1 | INTEGER | read-write | Enable 3 way conference feature. Access: Offline. AC INI-Param: ENABLE3WAYCONFERENCE |
| STR supServicesConferenceEstablishCode | 1.3.6.1.4.1.5003.9.10.3.1.1.7.14.2 | SnmpAdminString | read-write | Control Key activation of the 3 way conference. Access: Instant. AC INI-Param: CONFERENCECODE |
| INT supServicesEnableHold | 1.3.6.1.4.1.5003.9.10.3.1.1.7.1 | INTEGER | read-write | Enable Call Hold service. Access: Instant. AC INI-Param: ENABLEHOLD |
| INT supServicesEnableHold2ISDN | 1.3.6.1.4.1.5003.9.10.3.1.1.7.8 | INTEGER | read-write | Enable Hold/retrieve from and to ISDN. Access: Instant. AC INI-Param: ENABLEHOLD2ISDN |
| INT supServicesEnableMOH | 1.3.6.1.4.1.5003.9.10.3.1.1.7.9 | INTEGER | read-write | FXS: enable playing Music On Hold (instead of Held tone to the PSTN side). Access: Instant. AC INI-Param: EnableMOH |
| I32 supServicesHeldTimeout | 1.3.6.1.4.1.5003.9.10.3.1.1.7.5 | Integer32 | read-write | Maximum time allowed for call to be retreived from IP (seconds). Access: Instant. AC INI-Param: HELDTIMEOUT |
| INT supServicesHoldFormat | 1.3.6.1.4.1.5003.9.10.3.1.1.7.3 | INTEGER | read-write | Call Hold format - Zero IP or 'sendonly' SDP attribute. Access: Instant. AC INI-Param: HOLDFORMAT |
| STR supServicesHookFlashCode | 1.3.6.1.4.1.5003.9.10.3.1.1.7.6 | SnmpAdminString | read-write | If this code received during session, act as if hook flash received from the TEL side. This parameter can use DIGIT MAP syntax. Access: Instant. AC INI-Param: HookFlashCode |
| INT supServicesNameID | 1.3.6.1.4.1.5003.9.10.3.1.1.7.2 | INTEGER | read-write | Enable Name Identification service. Access: Instant. AC INI-Param: ENABLENAMEIDENTIFICATION |
| INT supServicesSendMeteringMessageToIP | 1.3.6.1.4.1.5003.9.10.3.1.1.7.4 | INTEGER | read-write | Send metering messages to IP on detection of analog metering pulses. Access: Instant. AC INI-Param: SENDMETERING2IP |
| INT tel2IPRoutingAction | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT tel2IPRoutingActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| STR tel2IPRoutingAddress | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.6 | SnmpAdminString | read-create | Address (IP or DNS name). Access: Instant. AC INI-Param: PREFIX_DestAddress |
| U32 tel2IPRoutingChargeCode | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.9 | Unsigned32 | read-create | Charge code to use for generating metering tones. Access: Instant. AC INI-Param: PREFIX_MeteringCode |
| STR tel2IPRoutingDestHostPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.12 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: PREFIX_DestHostPrefix |
| I32 tel2IPRoutingDestIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.13 | Integer32 | read-create | Access: Instant. AC INI-Param: PREFIX_DestIPGroupID |
| U32 tel2IPRoutingDestPort | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.10 | Unsigned32 | read-create | Destination port. Access: Instant. AC INI-Param: PREFIX_DestPort |
| tel2IPRoutingEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1 | not-accessible | ||
| U32 tel2IPRoutingIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.1 | Unsigned32 | not-accessible | Entry number, starting at 0. AC INI-Param: PREFIX_Index |
| STR tel2IPRoutingPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.5 | SnmpAdminString | read-create | Phone number prefix. up to 50 digits. can be used for defining range of phone numbers. Access: Instant. AC INI-Param: PREFIX_DestinationPrefix |
| I32 tel2IPRoutingProfileID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.8 | Integer32 | read-create | Profile ID. Access: Instant. AC INI-Param: PREFIX_ProfileId |
| ROW tel2IPRoutingRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. Access: Instant. AC INI-Param: N/A |
| STR tel2IPRoutingSourceHostPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.14 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: PREFIX_SrcHostPrefix |
| I32 tel2IPRoutingSourceIPGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.11 | Integer32 | read-create | Access: Instant. AC INI-Param: PREFIX_SrcIPGroupID |
| I32 tel2IPRoutingSourceTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.16 | Integer32 | read-create | Access: Instant. AC INI-Param: PREFIX_SrcTrunkGroupID |
| STR tel2IPRoutingSrcPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.7 | SnmpAdminString | read-create | Calling Phone number prefix. up to 50 digits. can be used for defining range of phone numbers. Access: Instant. AC INI-Param: PREFIX_SourcePrefix |
| tel2IPRoutingTable | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1 | not-accessible | Phone prefix to IP address routing table. The table is used for routing incoming PSTN to IP calls, if Gatekeeper is not used. | |
| INT tel2IPRoutingTransportType | 1.3.6.1.4.1.5003.9.10.3.1.1.2.20.1.1.15 | INTEGER | read-create | Access: Instant. AC INI-Param: PREFIX_TransportType |
| INT telProfileAction | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT telProfileActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| U32 telProfileCodersGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.7 | Unsigned32 | read-create | Coders Group ID. Access: Instant. AC INI-Param: TelProfile_CodersGroupID |
| I32 telProfileDialPlanIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.31 | Integer32 | read-create | Defines the plan index to be used from the external Dial Plan file. Access: Instant. AC INI-Param: TelProfile_DialPlanIndex |
| INT telProfileDisconnectOnBusyTone | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.29 | INTEGER | read-create | Access: Instant. AC INI-Param: TelProfile_DisconnectOnBusyTone |
| U32 telProfileDJBufMinDelay | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.10 | Unsigned32 | read-create | Dynamic Jitter Buffer Minimum Delay (msec). Access: Instant. AC INI-Param: TelProfile_JitterBufMinDelay |
| U32 telProfileDJBufOptFactor | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.11 | Unsigned32 | read-create | Dynamic jitter buffer frame error/delay optimization. Access: Instant. AC INI-Param: TelProfile_JitterBufOptFactor |
| I32 telProfileDTMFVolume | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.15 | Integer32 | read-create | DTMF Volume. Access: Instant. AC INI-Param: TelProfile_DtmfVolume |
| INT telProfileECE | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.20 | INTEGER | read-create | Enables or disables the echo canceler. Access: Instant. AC INI-Param: TelProfile_EnableEC |
| INT telProfileECNlpMode | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.35 | INTEGER | read-create | Access: Instant. AC INI-Param: TelProfile_ECNlpMode |
| INT telProfileEnable911PSAP | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.32 | INTEGER | read-create | GwApp Tel Profile Table. Access: Instant. AC INI-Param: TelProfile_Enable911PSAP |
| INT telProfileEnableAGC | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.34 | INTEGER | read-create | Access: Instant. AC INI-Param: TelProfile_EnableAGC |
| INT telProfileEnableCurrentDisconnect | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.18 | INTEGER | read-create | Disconnect call upon detection of current disconnect signal. Access: Instant. AC INI-Param: TelProfile_EnableCurrentDisconnect |
| INT telProfileEnableDIDWink | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.27 | INTEGER | read-create | Access: Instant. AC INI-Param: TelProfile_EnableDIDWink |
| INT telProfileEnableDigitDelivery | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.19 | INTEGER | read-create | Enables Digit delivery to TEL side. Access: Instant. AC INI-Param: TelProfile_EnableDigitDelivery |
| INT telProfileEnableEarlyMedia | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.24 | INTEGER | read-create | Enable Early Media. Access: Instant. AC INI-Param: TelProfile_EnableEarlyMedia |
| INT telProfileEnableReversalPolarity | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.17 | INTEGER | read-create | FXO: Connect/Disconnect calls upon detection of polarity reversal signal. FXS: generate the signal. Access: Instant. AC INI-Param: TelProfile_EnableReversePolarity |
| INT telProfileEnableVoiceMailDelay | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.30 | INTEGER | read-create | Access: Instant. AC INI-Param: TelProfile_EnableVoiceMailDelay |
| telProfileEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1 | not-accessible | ||
| U32 telProfileFaxTransportMode | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.8 | Unsigned32 | read-write | Fax Transport Mode. Access: Instant. AC INI-Param: N/A |
| U32 telProfileIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.1 | Unsigned32 | not-accessible | Entry number, starting at 1. AC INI-Param: TelProfile_Index |
| I32 telProfileInputGain | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.16 | Integer32 | read-create | Input Gain. Access: Instant. AC INI-Param: TelProfile_InputGain |
| U32 telProfileIPDiffServ | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.12 | Unsigned32 | read-create | IP DiffServ byte value. Access: Instant. AC INI-Param: TelProfile_IPDiffServ |
| INT telProfileIsFaxUsed | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.9 | INTEGER | read-create | Use H.323/Annex D procedure for real time FAX relay. To use this feature, disable inband DTMF by setting the FaxTransportMode to 1.0 - No fax , 1- T.38 , 2- Fax Fallback (G.711 with optimization). Access: Instant. AC INI-Param: TelProfile_IsFaxUsed |
| INT telProfileIsTwoStageDial | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.28 | INTEGER | read-create | Access: Instant. AC INI-Param: TelProfile_IsTwoStageDial |
| U32 telProfileMaxFlashHookDetectionPeriod | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.23 | Unsigned32 | read-create | Access: Instant. AC INI-Param: TelProfile_FlashHookPeriod |
| INT telProfileMWIanalogLamp | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.21 | INTEGER | read-create | Enable MWI support using an analog lamp (110 Volt). Access: Instant. AC INI-Param: TelProfile_MWIAnalog |
| INT telProfileMWIDisplay | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.22 | INTEGER | read-create | Enable MWI support using Caller ID interface. Access: Instant. AC INI-Param: TelProfile_MWIDisplay |
| U32 telProfilePreference | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.5 | Unsigned32 | read-create | Preference. Access: Instant. AC INI-Param: TelProfile_TelPreference |
| STR telProfileProfileName | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.6 | SnmpAdminString | read-create | Profile Name. Access: Instant. AC INI-Param: TelProfile_ProfileName |
| INT telProfileProgressIndicatorToIP | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.25 | INTEGER | read-create | Determine whether to send the Progress Indicator to IP. Access: Instant. AC INI-Param: TelProfile_ProgressIndicator2IP |
| ROW telProfileRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| U32 telProfileSigIPDiffServ | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.13 | Unsigned32 | read-create | Type Of Service bits in IP header of signalling messages. Access: Instant. AC INI-Param: TelProfile_SigIPDiffServ |
| INT telProfileSwapTelToIpPhoneNumbers | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.33 | INTEGER | read-create | GwApp Tel Profile Table. Access: Instant. AC INI-Param: TelProfile_SwapTelToIpPhoneNumbers |
| telProfileTable | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22 | not-accessible | ||
| U32 telProfileTimeForReorderTone | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.26 | Unsigned32 | read-create | Duration of reorder tone playing before FXO releases line. Access: Instant. AC INI-Param: TelProfile_TimeForReorderTone |
| I32 telProfileVoiceVolume | 1.3.6.1.4.1.5003.9.10.3.1.1.15.22.1.14 | Integer32 | read-create | Voice Volume. Access: Instant. AC INI-Param: TelProfile_VoiceVolume |
| INT toneIndexAction | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT toneIndexActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| toneIndexEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1 | not-accessible | ||
| U32 toneIndexFXSPortFirst | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.5 | Unsigned32 | read-create | Staring Range of FXS Port. Access: Instant. AC INI-Param: ToneIndex_FXSPort_First |
| U32 toneIndexFXSPortLast | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.6 | Unsigned32 | read-create | End Range of FXS Port. Access: Instant. AC INI-Param: ToneIndex_FXSPort_Last |
| U32 toneIndexIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.1 | Unsigned32 | not-accessible | Charge code index. AC INI-Param: ToneIndex_Index |
| U32 toneIndexPriorityIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.8 | Unsigned32 | read-create | Index used for distinctive ringing and call waiting tones. Access: Instant. AC INI-Param: ToneIndex_PriorityIndex |
| ROW toneIndexRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| STR toneIndexSourcePrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22.1.7 | SnmpAdminString | read-create | Source Prefix. Access: Instant. AC INI-Param: ToneIndex_SourcePrefix |
| toneIndexTable | 1.3.6.1.4.1.5003.9.10.3.1.1.4.10.22 | not-accessible | ||
| tones | 1.3.6.1.4.1.5003.9.10.3.1.1.8 | |||
| INT tonesEnableComfortTone | 1.3.6.1.4.1.5003.9.10.3.1.1.8.10 | INTEGER | read-write | Enable Comfort Tone for playing a patience comfort tone between Invite and 18x response. [0] - Disabled [1] - Enabled. Comfort Tone will be played. Access: Instant. AC INI-Param: ENABLECOMFORTTONE |
| I32 tonesFirstCallRBTId | 1.3.6.1.4.1.5003.9.10.3.1.1.8.7 | Integer32 | read-write | the index of the first Call RB tone in the call-progress tones file. Access: Instant. AC INI-Param: FIRSTCALLRBTID |
| I32 tonesFirstCallWaitingToneID | 1.3.6.1.4.1.5003.9.10.3.1.1.8.9 | Integer32 | read-write | The index of the first Call Waiting tone in the call-progress tones file. Access: Instant. AC INI-Param: FIRSTCALLWAITINGTONEID |
| INT tonesPlayRBTone2Ip | 1.3.6.1.4.1.5003.9.10.3.1.1.8.3 | INTEGER | read-write | Enable ringback tone playing towards IP. Refer to User's Manual for details. Access: Instant. AC INI-Param: PLAYRBTONE2IP |
| INT tonesPlayRBTone2Tel | 1.3.6.1.4.1.5003.9.10.3.1.1.8.4 | INTEGER | read-write | Enable ringback tone playing towards Tel side. Refer to User's Manual for details. Access: Instant. AC INI-Param: PLAYRBTONE2TEL |
| INT tonesPlayRBToneXferSuccess | 1.3.6.1.4.1.5003.9.10.3.1.1.8.6 | INTEGER | read-write | Play RB tone on transfer success. Access: Instant. AC INI-Param: PLAYRBTONEONXFER |
| I32 tonesPrecedenceRingingType | 1.3.6.1.4.1.5003.9.10.3.1.1.8.8 | Integer32 | read-write | the index of the first Call RB tone in the call-progress tones file. Access: Instant. AC INI-Param: PRECEDENCERINGINGTYPE |
| U32 tonesStutterToneDuration | 1.3.6.1.4.1.5003.9.10.3.1.1.8.5 | Unsigned32 | read-write | Time for playing confirmation tone before normal dial tone is played (msec). Access: Instant. AC INI-Param: STUTTERTONEDURATION |
| U32 tonesTimeForDialTone | 1.3.6.1.4.1.5003.9.10.3.1.1.8.2 | Unsigned32 | read-write | Duration of played dial tone after the gateway seizes the line in response to ringing. Access: Instant. AC INI-Param: TIMEFORDIALTONE |
| U32 tonesTimeForReorderTone | 1.3.6.1.4.1.5003.9.10.3.1.1.8.1 | Unsigned32 | read-write | Duration of reorder tone playing before FXO releases line. Access: Instant. AC INI-Param: TIMEFORREORDERTONE |
| transcoding | 1.3.6.1.4.1.5003.9.10.3.1.1.5.14 | |||
| STR transcodingID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.14.1 | SnmpAdminString | read-write | SIP Transcoding ID. Access: Instant. AC INI-Param: TRANSCODINGID |
| transfer | 1.3.6.1.4.1.5003.9.10.3.1.1.7.10 | |||
| INT transferEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.7.10.1 | INTEGER | read-write | Enable Call Transfer service. Access: Instant. AC INI-Param: ENABLETRANSFER |
| STR transferXferPrefix | 1.3.6.1.4.1.5003.9.10.3.1.1.7.10.2 | SnmpAdminString | read-write | Prefix added to the called number of a transferred call. Access: Instant. AC INI-Param: XFERPREFIX |
| INT trunkGroupSettingsAction | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.3 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT trunkGroupSettingsActionResult | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.4 | INTEGER | read-only | Development Impending. AC INI-Param: N/A |
| INT trunkGroupSettingsChannelSelectMode | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.6 | INTEGER | read-create | Selects the next available (free) Gateway port, FXO/PSTN: affects outgoing calls chanel selection FXS:affects incoming call channel selection. Access: Instant. AC INI-Param: TrunkGroupSettings_ChannelSelectMode |
| STR trunkGroupSettingsContactUser | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.9 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: TrunkGroupSettings_ContactUser |
| trunkGroupSettingsEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1 | not-accessible | ||
| STR trunkGroupSettingsGatewayName | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.8 | SnmpAdminString | read-create | Access: Instant. AC INI-Param: TrunkGroupSettings_GatewayName |
| U32 trunkGroupSettingsIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.1 | Unsigned32 | not-accessible | Trunk numbers, starting at 0. AC INI-Param: TrunkGroupSettings_Index |
| INT trunkGroupSettingsMwiInterrogationType | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.11 | INTEGER | read-create | Access: Instant. AC INI-Param: TrunkGroupSettings_MWIInterrogationType |
| INT trunkGroupSettingsRegistrationMode | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.7 | INTEGER | read-create | Access: Instant. AC INI-Param: TrunkGroupSettings_RegistrationMode |
| ROW trunkGroupSettingsRowStatus | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.2 | RowStatus | read-create | Row-Status Textual Conventions as defined in RFC 2579: Textual Conventions for SMIv2. AC INI-Param: N/A |
| I32 trunkGroupSettingsServingIPGroup | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.10 | Integer32 | read-create | Access: Instant. AC INI-Param: TrunkGroupSettings_ServingIPGroup |
| trunkGroupSettingsTable | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22 | not-accessible | The table defines trunk/hunt groups configuration | |
| U32 trunkGroupSettingsTrunkGroupID | 1.3.6.1.4.1.5003.9.10.3.1.1.1.22.1.5 | Unsigned32 | read-create | Trunk/Hunt group ID. Access: Instant. AC INI-Param: TrunkGroupSettings_TrunkGroupId |
| trunkTransferEntry | 1.3.6.1.4.1.5003.9.10.3.1.1.3.22.1 | not-accessible | ||
| U32 trunkTransferIndex | 1.3.6.1.4.1.5003.9.10.3.1.1.3.22.1.1 | Unsigned32 | not-accessible | Trunk number. AC INI-Param: N/A |
| INT trunkTransferMode | 1.3.6.1.4.1.5003.9.10.3.1.1.3.22.1.2 | INTEGER | read-write | The type of transfer the PSTN/PBX supports. Access: Instant. AC INI-Param: TRUNKTRANSFERMODE |
| trunkTransferTable | 1.3.6.1.4.1.5003.9.10.3.1.1.3.22 | not-accessible | Trunk Transfer Mode table. | |
| vmDigitPattern | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20 | |||
| STR vmDigitPatternConnectCode | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.8 | SnmpAdminString | read-write | Play Code string to Tel side when connect message recieved from IP side. Access: Instant. AC INI-Param: TELCONNECTCODE |
| STR vmDigitPatternDigitToIgnore | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.13 | SnmpAdminString | read-write | A digit (0-9,A-D,* or #) that if received as Src (S) or Redirect (R), the digit is ignored and not added to that number. Used in DTMF VoiceMail. Access: Instant. AC INI-Param: DigitPatternDigitToIgnore |
| STR vmDigitPatternDisconnectCode | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.7 | SnmpAdminString | read-write | Disconnect call if digit string is received from the TEL side during session. Access: Instant. AC INI-Param: TelDisconnectCode |
| STR vmDigitPatternExternalCall | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.6 | SnmpAdminString | read-write | Digit pattern used to indicate external call (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternExternalCall |
| STR vmDigitPatternInternalCall | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.5 | SnmpAdminString | read-write | Digit pattern used to indicate internal call (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternInternalCall |
| STR vmDigitPatternNoReason | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.1 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward with no reason (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardNoReason |
| STR vmDigitPatternOnBusy | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.2 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on busy (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardOnBusy |
| STR vmDigitPatternOnDND | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.4 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on Do Not Disturb (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardOnDND |
| STR vmDigitPatternOnNoAnswer | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.3 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on no answer (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardOnNoAnswer |
| STR vmDigitPatternVmDigitPatternNoReasonExternal | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.12 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward with no reason (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardNoReasonExt |
| STR vmDigitPatternVmDigitPatternOnBusyExternal | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.9 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on busy (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardOnBusyExt |
| STR vmDigitPatternVmDigitPatternOnDNDExternal | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.11 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on Do Not Disturb (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardOnDNDExt |
| STR vmDigitPatternVmDigitPatternOnNoAnswerExternal | 1.3.6.1.4.1.5003.9.10.3.1.1.16.20.10 | SnmpAdminString | read-write | Digit pattern used to indicate Call Forward on no answer (PBX to VoiceMail). Access: Instant. AC INI-Param: DigitPatternForwardOnNoAnswerExt |
| vmMWI | 1.3.6.1.4.1.5003.9.10.3.1.1.16.21 | |||
| STR vmMWIOffCode | 1.3.6.1.4.1.5003.9.10.3.1.1.16.21.2 | SnmpAdminString | read-write | Digit pattern used to notify PBX about no messages waiting for extension (added as prefix). Access: Instant. AC INI-Param: MWIOffCode |
| STR vmMWIOnCode | 1.3.6.1.4.1.5003.9.10.3.1.1.16.21.1 | SnmpAdminString | read-write | Digit pattern used to notify PBX about messages waiting for extension (added as prefix). Access: Instant. AC INI-Param: MWIOnCode |
| STR vmMWISourceNumber | 1.3.6.1.4.1.5003.9.10.3.1.1.16.21.4 | SnmpAdminString | read-write | The phone number sent as source number toward PSTN for MWI setup. Access: Instant. AC INI-Param: MWISOURCENUMBER |
| STR vmMWISuffixCode | 1.3.6.1.4.1.5003.9.10.3.1.1.16.21.3 | SnmpAdminString | read-write | MWI suffix code used to notify PBX about messages waiting for extension (added as suffix to the extention number). Access: Instant. AC INI-Param: MWISuffixCode |
| vmSMDI | 1.3.6.1.4.1.5003.9.10.3.1.1.16.22 | |||
| INT vmSMDIEnable | 1.3.6.1.4.1.5003.9.10.3.1.1.16.22.1 | INTEGER | read-write | Enables the Simplified Message Desk Interface (SMDI). SMDI defines a method whereby telephony systems can provide voice-messaging systems with data required by those telephony systems to process incoming calls intelligently. Whenever the phone system routes a call, it sends an SMDI message through an EIA/TIA-232 connection to the voice-messaging system that tells it the line that it is using, the type of call that it is forwarding, and information about the source and destination of the call. 0 = Normal Serial 1 = Serial SMDI. Access: Offline. AC INI-Param: SMDI |
| U32 vmSMDITimeOut | 1.3.6.1.4.1.5003.9.10.3.1.1.16.22.2 | Unsigned32 | read-write | Time out for: 1. From SMDI Info until SETUP 2. From SETUP until SMDI event. Access: Instant. AC INI-Param: SMDITimeOut |
| voiceMail | 1.3.6.1.4.1.5003.9.10.3.1.1.16 | |||
| INT voiceMailInterface | 1.3.6.1.4.1.5003.9.10.3.1.1.16.2 | INTEGER | read-write | Selects the method of communication between PBX and the Gateway, that is used instead of legacy voicemail. Access: Instant. AC INI-Param: VoiceMailInterface |
| INT voiceMailLineTransferMode | 1.3.6.1.4.1.5003.9.10.3.1.1.16.1 | INTEGER | read-write | LineTransferMode: 0-ip 1-pbx blind transfer 2-pbx semi supv transfer 3-supervised transfer (also known as warm transfer). (in TP, feature key and parameter EnableIPMDetectors needed). Access: Instant. AC INI-Param: LineTransferMode |
| vxml | 1.3.6.1.4.1.5003.9.10.3.1.1.5.12 | |||
| STR vxmlID | 1.3.6.1.4.1.5003.9.10.3.1.1.5.12.1 | SnmpAdminString | read-write | Identification of VoiceXML call (To be used by SIP INVITE). Access: Instant. AC INI-Param: VXMLID |
| U32 vxmlNumOfEndPoints | 1.3.6.1.4.1.5003.9.10.3.1.1.5.12.2 | Unsigned32 | read-write | Number of VXML endpoints. Access: Offline. AC INI-Param: NUMOFVXMLENDPOINTS |
RFC description
AudioCodes gateway MIB for managing configuration of voice gateway devices including channel settings, trunk allocation, and gateway parameters.
Start monitoring AudioCodes media/VoIP gateways with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.