ATM-SOFT-PVC-MIB

All MIBs › ATM-SOFT-PVC-MIB

Category: ATM

Description:

Manages ATM Soft Permanent Virtual Circuits (Soft PVCs), covering endpoint configuration and call setup status.

Imported Objects

atmVclVci	OBJECT-TYPE
atmVclVpi	OBJECT-TYPE
atmVplVpi	OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

enterprises

From SNMPv2-SMI-v1

Counter32
Gauge32

From SNMPv2-TC-v1

RowStatus
TimeStamp
TruthValue

What Is ATM-SOFT-PVC-MIB?

ATM-SOFT-PVC-MIB is an ATM Forum/IETF-derived standards MIB for managing ATM Soft Permanent Virtual Circuits (Soft PVCs), a hybrid ATM connection type that combines PVC-like provisioning with SVC-style dynamic call setup. It exposes configuration for soft PVC endpoints, including target address, VPI/VCI selection, and call setup parameters, along with counters and flags for call failure tracking. Its monitoring value is centered on fault detection for these ATM connections: it tracks the count of soft PVC call failures, the number of currently failing soft PVCCs and PVPCs, and can generate traps at a configurable notification interval when failures occur, directly surfacing connection-level fault status on ATM switching equipment. As an ATM Forum-aligned standard it works alongside other standard ATM MIBs (such as the base ATM-MIB) for complete circuit management. It is deployed in carrier and enterprise ATM switch networks using soft PVCs for resilient virtual circuit provisioning. When decoding a specific fault trap, an operator can consult the ATM-SOFT-PVC-MIB OID list to map the numeric identifier back to the exact soft-PVC object it represents.

IPNetwork Monitor allows you to monitor SNMP objects defined in ATM-SOFT-PVC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

soft PVC call failure count
currently failing soft PVCCs/PVPCs
target address, VPI/VCI for soft PVC endpoints
call failure trap enable/interval

Supported Devices

ATM switch/router supporting Soft PVC (ATM Forum-compliant)

Monitoring Examples

An administrator would poll atmSoftPvcCallFailures and atmSoftPvcCurrentlyFailingSoftPVccs/atmSoftPvcCurrentlyFailingSoftPVpcs to detect ATM soft virtual circuits that are currently unable to establish a call, indicating a routing or endpoint reachability problem. Examining atmSoftPVccTable/atmSoftPVccEntry, indexed by atmSoftPVccLeafReference, would show the atmSoftPVccTargetAddress, atmSoftPVccTargetVpi, and atmSoftPVccTargetVci for a specific failing circuit, while atmSoftPvcCallFailuresTrapEnable and atmSoftPvcNotificationInterval control whether and how often traps are sent for these failures.

OIDs

OID symbolic	OID numeric	Type	Access	Description
atmCurrentlyFailingSoftPVccEntry	1.3.6.1.4.1.353.5.5.1.1.5.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVccMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.5
atmCurrentlyFailingSoftPVccTable	1.3.6.1.4.1.353.5.5.1.1.5		not-accessible	A table indicating all Soft Permanent Virtual Channel Connections (Soft PVCCs) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
TIM atmCurrentlyFailingSoftPVccTimeStamp	1.3.6.1.4.1.353.5.5.1.1.5.1.1	TimeStamp	read-only	The time at which this Soft PVCC began to fail.
atmCurrentlyFailingSoftPVpcEntry	1.3.6.1.4.1.353.5.5.1.1.6.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVpcMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.6
atmCurrentlyFailingSoftPVpcTable	1.3.6.1.4.1.353.5.5.1.1.6		not-accessible	A table indicating all Soft Permanent Virtual Path Connections (Soft PVPCs) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
TIM atmCurrentlyFailingSoftPVpcTimeStamp	1.3.6.1.4.1.353.5.5.1.1.6.1.1	TimeStamp	read-only	The time at which this Soft PVPC began to fail.
atmForum	1.3.6.1.4.1.353
atmForumNetworkManagement	1.3.6.1.4.1.353.5
atmfSoftPvc	1.3.6.1.4.1.353.5.5
ATM atmInterfaceSoftPvcAddress	1.3.6.1.4.1.353.5.5.1.1.4.1.1	AtmAddr	not-accessible	Specifies the address that can be used to establish a Soft PVCC or Soft PVPC to this interface.
atmInterfaceSoftPvcAddressEntry	1.3.6.1.4.1.353.5.5.1.1.4.1		not-accessible	ATM address entry for configuring Soft PVCCs or Soft PVPCs at an ATM interface.
ROW atmInterfaceSoftPvcAddressRowStatus	1.3.6.1.4.1.353.5.5.1.1.4.1.2	RowStatus	read-write	Used to create and delete an ATM address at this interface for setting up Soft PVCCs or Soft PVPCs.
atmInterfaceSoftPvcAddressTable	1.3.6.1.4.1.353.5.5.1.1.4		not-accessible	This table is used to configure ATM addresses at an ATM interface on this node prior to setting up Soft PVPCs or Soft PVPCs at that interface.
atmSoftPvcAddressMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.4
atmSoftPvcBaseGroup	1.3.6.1.4.1.353.5.5.1.1.1
atmSoftPvcBaseMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.1
C32 atmSoftPvcCallFailures	1.3.6.1.4.1.353.5.5.1.1.1.2	Counter32	read-only	The number of times a series of call attempts has failed to establish a Soft PVCC or Soft PVPC. The number of call attempts in a series is determined by atmSoftPVccRetryThreshold or atmSoftPVpcRetryThreshold, respectively.
NTF atmSoftPvcCallFailuresTrap	1.3.6.1.4.1.353.5.5.1.2.1.0.1			A notification indicating that one or more series of call attempts in trying to establish a Soft PVPC or Soft PVCC have failed since the last atmSoftPvcCallFailureTrap was sent. If this trap has not been sent for the last atmSoftPvcNotificationInterval, then it will be sent on the next increment of atmSoftPvcCallFailures.
T/F atmSoftPvcCallFailuresTrapEnable	1.3.6.1.4.1.353.5.5.1.1.1.1	TruthValue	read-write	Allows the generation of traps in response to call failures. By default, this object is set to 'false'.
atmSoftPVccEntry	1.3.6.1.4.1.353.5.5.1.1.2.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) originating at a switch interface. A Soft PVCC is a VCC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVclTable must be created, defining a VCL on the source interface, prior to creating an atmSoftPVccEntry row. The row in the atmVclTable must be active prior to activating the atmSoftPVccEntry row. The contents of this table reflect only the characteristics unique to a Soft PVCC. The traffic parameters are defined in the VCL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVCCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVccRowStatus) can be set while the row is active. At the destination, the VCL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVclVpi, and atmVclVci specified in the index clause of this entry serves to identify the VCL on the source interface. The atmSoftPVccLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVCC.
INT atmSoftPVccLastReleaseCause	1.3.6.1.4.1.353.5.5.1.1.2.1.6	INTEGER	read-only	Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC. Indicates the reason for the Release.
OCT atmSoftPVccLastReleaseDiagnostic	1.3.6.1.4.1.353.5.5.1.1.2.1.7	OCTET STRING	read-only	Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC.
INT atmSoftPVccLeafReference	1.3.6.1.4.1.353.5.5.1.1.2.1.1	INTEGER	not-accessible	An arbitrary integer which, in the case of the source VCL having an atmVclCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVCC. If the atmVclCastType is not 'p2mpRoot' the value 1 shall be used.
INT atmSoftPVccOperStatus	1.3.6.1.4.1.353.5.5.1.1.2.1.8	INTEGER	read-only	Describes the status of the Soft PVCC. Valid values are: other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
INT atmSoftPVccRestart	1.3.6.1.4.1.353.5.5.1.1.2.1.9	INTEGER	read-write	When the value is set to 'restart' the Soft PVCC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVccOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVccRetryFailures object is cleared When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned.
G32 atmSoftPVccRetryFailures	1.3.6.1.4.1.353.5.5.1.1.2.1.13	Gauge32	read-only	Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVCC is restarted.
INT atmSoftPVccRetryInterval	1.3.6.1.4.1.353.5.5.1.1.2.1.10	INTEGER	read-write	Defines the period to wait before attempting to establish the Soft PVCC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
INT atmSoftPVccRetryLimit	1.3.6.1.4.1.353.5.5.1.1.2.1.14	INTEGER	read-write	Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVccRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
INT atmSoftPVccRetryThreshold	1.3.6.1.4.1.353.5.5.1.1.2.1.12	INTEGER	read-write	Indicates the number of consecutive call setup attempts for the same Soft PVCC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVCC.
INT atmSoftPVccRetryTimer	1.3.6.1.4.1.353.5.5.1.1.2.1.11	INTEGER	read-only	Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVCC. When the timer is not running, the value zero shall be returned.
ROW atmSoftPVccRowStatus	1.3.6.1.4.1.353.5.5.1.1.2.1.15	RowStatus	read-write	Used to create and delete a Soft PVCC. When this object is set to 'active' an attempt is made to set up the Soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
atmSoftPVccTable	1.3.6.1.4.1.353.5.5.1.1.2		not-accessible	The (conceptual) table used to manage Soft Permanent Virtual Channel Connections (Soft PVCCs). The Soft PVCC table is applicable only to switches.
ATM atmSoftPVccTargetAddress	1.3.6.1.4.1.353.5.5.1.1.2.1.2	AtmAddr	read-write	The target ATM Address of this Soft PVCC. If no address is supplied, no attempts to establish the Soft PVCC are initiated.
INT atmSoftPVccTargetSelectType	1.3.6.1.4.1.353.5.5.1.1.2.1.3	INTEGER	read-write	Indicates whether the target VPI/VCI values are to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI/VCI values. In such a case, once the Soft PVCC atmSoftPVccOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI/VCI values will continue to be used even if the connection is subsequently torn down and re-established. The VPI/VCI values chosen will be available for reading in atmSoftPVccTargetVpi and atmSoftPVccTargetVci. If the value 'required' is specified, then values must be supplied for objects atmSoftPVccTargetVpi and atmSoftPVccTargetVci prior to activation of the row. These values are then to be used at the destination.
INT atmSoftPVccTargetVci	1.3.6.1.4.1.353.5.5.1.1.2.1.5	INTEGER	read-write	The VCI value of the VCL used at the target interface. This value must be filled in when the atmSoftPVccTargetSelectType is set to 'required'.This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
INT atmSoftPVccTargetVpi	1.3.6.1.4.1.353.5.5.1.1.2.1.4	INTEGER	read-write	The VPI value of the VCL used at the target interface. This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
G32 atmSoftPvcCurrentlyFailingSoftPVccs	1.3.6.1.4.1.353.5.5.1.1.1.3	Gauge32	read-only	The current number of Soft PVCCs for which there is an active row in the atmSoftPVccTable having an atmSoftPVccOperStatus with a value other than 'connected'.
G32 atmSoftPvcCurrentlyFailingSoftPVpcs	1.3.6.1.4.1.353.5.5.1.1.1.4	Gauge32	read-only	The current number of Soft PVPCs for which there is an active row in the atmSoftPVpcTable having an atmSoftPVpcOperStatus with a value other than 'connected'.
atmSoftPvcMIB	1.3.6.1.4.1.353.5.5.1
atmSoftPvcMIBCompliance	1.3.6.1.4.1.353.5.5.1.3.1.1
atmSoftPvcMIBCompliances	1.3.6.1.4.1.353.5.5.1.3.1
atmSoftPvcMIBConformance	1.3.6.1.4.1.353.5.5.1.3
atmSoftPvcMIBGroups	1.3.6.1.4.1.353.5.5.1.3.2
atmSoftPvcMIBObjects	1.3.6.1.4.1.353.5.5.1.1
atmSoftPvcMIBTraps	1.3.6.1.4.1.353.5.5.1.2
INT atmSoftPvcNotificationInterval	1.3.6.1.4.1.353.5.5.1.1.1.5	INTEGER	read-write	The minimum interval between the sending of atmSoftPvcCallFailuresTrap notifications.
atmSoftPvcTraps	1.3.6.1.4.1.353.5.5.1.2.1
atmSoftPvcTrapsPrefix	1.3.6.1.4.1.353.5.5.1.2.1.0
atmSoftPvcVccMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.2
atmSoftPvcVpcMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.3
atmSoftPVpcEntry	1.3.6.1.4.1.353.5.5.1.1.3.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) originating at a switch interface. A Soft PVPC is a VPC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVplTable must be created, defining a VPL on the source interface, prior to creating an atmSoftPVpcEntry row. The row in the atmVplTable must be active prior to activating the atmSoftPVpcEntry row. The contents of this table reflect only the characteristics unique to a Soft PVPC. The traffic parameters are defined in the VPL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information, and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVPCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVpcRowStatus) can be set while the row is active. At the destination, the VPL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVplVpi specified in the index clause of this entry serves to identify the VPL on the source interface. The atmSoftPVpcLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVPC.
INT atmSoftPVpcLastReleaseCause	1.3.6.1.4.1.353.5.5.1.1.3.1.5	INTEGER	read-only	Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC. Indicates the reason for the Release.
OCT atmSoftPVpcLastReleaseDiagnostic	1.3.6.1.4.1.353.5.5.1.1.3.1.6	OCTET STRING	read-only	Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC.
INT atmSoftPVpcLeafReference	1.3.6.1.4.1.353.5.5.1.1.3.1.1	INTEGER	not-accessible	An arbitrary integer which, in the case of the source VPL having a atmVplCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVPC. If the atmVplCastType is not 'p2mpRoot', the value 1 shall be used.
INT atmSoftPVpcOperStatus	1.3.6.1.4.1.353.5.5.1.1.3.1.7	INTEGER	read-only	Describes the status of the Soft PVPC. other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
INT atmSoftPVpcRestart	1.3.6.1.4.1.353.5.5.1.1.3.1.8	INTEGER	read-write	When the value is set to 'restart', the Soft PVPC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVpcOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVpcRetryFailures object is cleared. When the value is set to 'noop', no operation is performed. When read, the value 'noop' is returned.
G32 atmSoftPVpcRetryFailures	1.3.6.1.4.1.353.5.5.1.1.3.1.12	Gauge32	read-only	Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVPC is restarted.
INT atmSoftPVpcRetryInterval	1.3.6.1.4.1.353.5.5.1.1.3.1.9	INTEGER	read-write	Defines the period to wait before attempting to establish the Soft PVPC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
INT atmSoftPVpcRetryLimit	1.3.6.1.4.1.353.5.5.1.1.3.1.13	INTEGER	read-write	Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVpcRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
INT atmSoftPVpcRetryThreshold	1.3.6.1.4.1.353.5.5.1.1.3.1.11	INTEGER	read-write	Indicates the number of consecutive call setup attempts for the same Soft PVPC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVPC.
INT atmSoftPVpcRetryTimer	1.3.6.1.4.1.353.5.5.1.1.3.1.10	INTEGER	read-only	Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVPC. When the timer is not running, the value zero shall be returned.
ROW atmSoftPVpcRowStatus	1.3.6.1.4.1.353.5.5.1.1.3.1.14	RowStatus	read-write	Used to create and delete a Soft PVPC. When this object is set to 'active' an attempt is made to set up the Soft PVPC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
atmSoftPVpcTable	1.3.6.1.4.1.353.5.5.1.1.3		not-accessible	The (conceptual) table used to manage Soft Permanent Virtual Path Connections (Soft PVPCs) The Soft PVPC table is applicable only to switches.
ATM atmSoftPVpcTargetAddress	1.3.6.1.4.1.353.5.5.1.1.3.1.2	AtmAddr	read-write	The target ATM Address of this Soft PVPC. If no address is supplied, no attempts to establish the Soft PVPC are initiated.
INT atmSoftPVpcTargetSelectType	1.3.6.1.4.1.353.5.5.1.1.3.1.3	INTEGER	read-write	Indicates whether the target VPI value is to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI value. In such a case, once the Soft PVPC atmSoftPVpcOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI value will continue to be used even if the connection is subsequently torn down and re-established. The VPI value chosen will be available for reading in atmSoftPVpcTargetVpi. If the value 'required' is specified, then a value must be supplied for object atmSoftPVpcTargetVpi prior to activation of the row. This value is then to be used at the destination.
INT atmSoftPVpcTargetVpi	1.3.6.1.4.1.353.5.5.1.1.3.1.4	INTEGER	read-write	The VPI value of the VPL used at the target interface. This value must be filled in when the atmSoftPVpcTargetSelectType is set to 'required'. This value is not relevant when the value of atmSoftPVpcTargetSelectType is 'any'.

OID symbolic	OID numeric	Type	Access	Description
atmForum	1.3.6.1.4.1.353
atmForumNetworkManagement	1.3.6.1.4.1.353.5
atmfSoftPvc	1.3.6.1.4.1.353.5.5
atmSoftPvcMIB	1.3.6.1.4.1.353.5.5.1
atmSoftPvcMIBObjects	1.3.6.1.4.1.353.5.5.1.1
atmSoftPvcBaseGroup	1.3.6.1.4.1.353.5.5.1.1.1
T/F atmSoftPvcCallFailuresTrapEnable	1.3.6.1.4.1.353.5.5.1.1.1.1	TruthValue	read-write	Allows the generation of traps in response to call failures. By default, this object is set to 'false'.
C32 atmSoftPvcCallFailures	1.3.6.1.4.1.353.5.5.1.1.1.2	Counter32	read-only	The number of times a series of call attempts has failed to establish a Soft PVCC or Soft PVPC. The number of call attempts in a series is determined by atmSoftPVccRetryThreshold or atmSoftPVpcRetryThreshold, respectively.
G32 atmSoftPvcCurrentlyFailingSoftPVccs	1.3.6.1.4.1.353.5.5.1.1.1.3	Gauge32	read-only	The current number of Soft PVCCs for which there is an active row in the atmSoftPVccTable having an atmSoftPVccOperStatus with a value other than 'connected'.
G32 atmSoftPvcCurrentlyFailingSoftPVpcs	1.3.6.1.4.1.353.5.5.1.1.1.4	Gauge32	read-only	The current number of Soft PVPCs for which there is an active row in the atmSoftPVpcTable having an atmSoftPVpcOperStatus with a value other than 'connected'.
INT atmSoftPvcNotificationInterval	1.3.6.1.4.1.353.5.5.1.1.1.5	INTEGER	read-write	The minimum interval between the sending of atmSoftPvcCallFailuresTrap notifications.
atmSoftPVccTable	1.3.6.1.4.1.353.5.5.1.1.2		not-accessible	The (conceptual) table used to manage Soft Permanent Virtual Channel Connections (Soft PVCCs). The Soft PVCC table is applicable only to switches.
atmSoftPVccEntry	1.3.6.1.4.1.353.5.5.1.1.2.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) originating at a switch interface. A Soft PVCC is a VCC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVclTable must be created, defining a VCL on the source interface, prior to creating an atmSoftPVccEntry row. The row in the atmVclTable must be active prior to activating the atmSoftPVccEntry row. The contents of this table reflect only the characteristics unique to a Soft PVCC. The traffic parameters are defined in the VCL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVCCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVccRowStatus) can be set while the row is active. At the destination, the VCL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVclVpi, and atmVclVci specified in the index clause of this entry serves to identify the VCL on the source interface. The atmSoftPVccLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVCC.
INT atmSoftPVccLeafReference	1.3.6.1.4.1.353.5.5.1.1.2.1.1	INTEGER	not-accessible	An arbitrary integer which, in the case of the source VCL having an atmVclCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVCC. If the atmVclCastType is not 'p2mpRoot' the value 1 shall be used.
ATM atmSoftPVccTargetAddress	1.3.6.1.4.1.353.5.5.1.1.2.1.2	AtmAddr	read-write	The target ATM Address of this Soft PVCC. If no address is supplied, no attempts to establish the Soft PVCC are initiated.
INT atmSoftPVccTargetSelectType	1.3.6.1.4.1.353.5.5.1.1.2.1.3	INTEGER	read-write	Indicates whether the target VPI/VCI values are to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI/VCI values. In such a case, once the Soft PVCC atmSoftPVccOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI/VCI values will continue to be used even if the connection is subsequently torn down and re-established. The VPI/VCI values chosen will be available for reading in atmSoftPVccTargetVpi and atmSoftPVccTargetVci. If the value 'required' is specified, then values must be supplied for objects atmSoftPVccTargetVpi and atmSoftPVccTargetVci prior to activation of the row. These values are then to be used at the destination.
INT atmSoftPVccTargetVpi	1.3.6.1.4.1.353.5.5.1.1.2.1.4	INTEGER	read-write	The VPI value of the VCL used at the target interface. This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
INT atmSoftPVccTargetVci	1.3.6.1.4.1.353.5.5.1.1.2.1.5	INTEGER	read-write	The VCI value of the VCL used at the target interface. This value must be filled in when the atmSoftPVccTargetSelectType is set to 'required'.This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
INT atmSoftPVccLastReleaseCause	1.3.6.1.4.1.353.5.5.1.1.2.1.6	INTEGER	read-only	Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC. Indicates the reason for the Release.
OCT atmSoftPVccLastReleaseDiagnostic	1.3.6.1.4.1.353.5.5.1.1.2.1.7	OCTET STRING	read-only	Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC.
INT atmSoftPVccOperStatus	1.3.6.1.4.1.353.5.5.1.1.2.1.8	INTEGER	read-only	Describes the status of the Soft PVCC. Valid values are: other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
INT atmSoftPVccRestart	1.3.6.1.4.1.353.5.5.1.1.2.1.9	INTEGER	read-write	When the value is set to 'restart' the Soft PVCC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVccOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVccRetryFailures object is cleared When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned.
INT atmSoftPVccRetryInterval	1.3.6.1.4.1.353.5.5.1.1.2.1.10	INTEGER	read-write	Defines the period to wait before attempting to establish the Soft PVCC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
INT atmSoftPVccRetryTimer	1.3.6.1.4.1.353.5.5.1.1.2.1.11	INTEGER	read-only	Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVCC. When the timer is not running, the value zero shall be returned.
INT atmSoftPVccRetryThreshold	1.3.6.1.4.1.353.5.5.1.1.2.1.12	INTEGER	read-write	Indicates the number of consecutive call setup attempts for the same Soft PVCC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVCC.
G32 atmSoftPVccRetryFailures	1.3.6.1.4.1.353.5.5.1.1.2.1.13	Gauge32	read-only	Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVCC is restarted.
INT atmSoftPVccRetryLimit	1.3.6.1.4.1.353.5.5.1.1.2.1.14	INTEGER	read-write	Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVccRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
ROW atmSoftPVccRowStatus	1.3.6.1.4.1.353.5.5.1.1.2.1.15	RowStatus	read-write	Used to create and delete a Soft PVCC. When this object is set to 'active' an attempt is made to set up the Soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
atmSoftPVpcTable	1.3.6.1.4.1.353.5.5.1.1.3		not-accessible	The (conceptual) table used to manage Soft Permanent Virtual Path Connections (Soft PVPCs) The Soft PVPC table is applicable only to switches.
atmSoftPVpcEntry	1.3.6.1.4.1.353.5.5.1.1.3.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) originating at a switch interface. A Soft PVPC is a VPC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVplTable must be created, defining a VPL on the source interface, prior to creating an atmSoftPVpcEntry row. The row in the atmVplTable must be active prior to activating the atmSoftPVpcEntry row. The contents of this table reflect only the characteristics unique to a Soft PVPC. The traffic parameters are defined in the VPL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information, and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVPCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVpcRowStatus) can be set while the row is active. At the destination, the VPL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVplVpi specified in the index clause of this entry serves to identify the VPL on the source interface. The atmSoftPVpcLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVPC.
INT atmSoftPVpcLeafReference	1.3.6.1.4.1.353.5.5.1.1.3.1.1	INTEGER	not-accessible	An arbitrary integer which, in the case of the source VPL having a atmVplCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVPC. If the atmVplCastType is not 'p2mpRoot', the value 1 shall be used.
ATM atmSoftPVpcTargetAddress	1.3.6.1.4.1.353.5.5.1.1.3.1.2	AtmAddr	read-write	The target ATM Address of this Soft PVPC. If no address is supplied, no attempts to establish the Soft PVPC are initiated.
INT atmSoftPVpcTargetSelectType	1.3.6.1.4.1.353.5.5.1.1.3.1.3	INTEGER	read-write	Indicates whether the target VPI value is to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI value. In such a case, once the Soft PVPC atmSoftPVpcOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI value will continue to be used even if the connection is subsequently torn down and re-established. The VPI value chosen will be available for reading in atmSoftPVpcTargetVpi. If the value 'required' is specified, then a value must be supplied for object atmSoftPVpcTargetVpi prior to activation of the row. This value is then to be used at the destination.
INT atmSoftPVpcTargetVpi	1.3.6.1.4.1.353.5.5.1.1.3.1.4	INTEGER	read-write	The VPI value of the VPL used at the target interface. This value must be filled in when the atmSoftPVpcTargetSelectType is set to 'required'. This value is not relevant when the value of atmSoftPVpcTargetSelectType is 'any'.
INT atmSoftPVpcLastReleaseCause	1.3.6.1.4.1.353.5.5.1.1.3.1.5	INTEGER	read-only	Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC. Indicates the reason for the Release.
OCT atmSoftPVpcLastReleaseDiagnostic	1.3.6.1.4.1.353.5.5.1.1.3.1.6	OCTET STRING	read-only	Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC.
INT atmSoftPVpcOperStatus	1.3.6.1.4.1.353.5.5.1.1.3.1.7	INTEGER	read-only	Describes the status of the Soft PVPC. other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
INT atmSoftPVpcRestart	1.3.6.1.4.1.353.5.5.1.1.3.1.8	INTEGER	read-write	When the value is set to 'restart', the Soft PVPC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVpcOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVpcRetryFailures object is cleared. When the value is set to 'noop', no operation is performed. When read, the value 'noop' is returned.
INT atmSoftPVpcRetryInterval	1.3.6.1.4.1.353.5.5.1.1.3.1.9	INTEGER	read-write	Defines the period to wait before attempting to establish the Soft PVPC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
INT atmSoftPVpcRetryTimer	1.3.6.1.4.1.353.5.5.1.1.3.1.10	INTEGER	read-only	Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVPC. When the timer is not running, the value zero shall be returned.
INT atmSoftPVpcRetryThreshold	1.3.6.1.4.1.353.5.5.1.1.3.1.11	INTEGER	read-write	Indicates the number of consecutive call setup attempts for the same Soft PVPC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVPC.
G32 atmSoftPVpcRetryFailures	1.3.6.1.4.1.353.5.5.1.1.3.1.12	Gauge32	read-only	Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVPC is restarted.
INT atmSoftPVpcRetryLimit	1.3.6.1.4.1.353.5.5.1.1.3.1.13	INTEGER	read-write	Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVpcRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
ROW atmSoftPVpcRowStatus	1.3.6.1.4.1.353.5.5.1.1.3.1.14	RowStatus	read-write	Used to create and delete a Soft PVPC. When this object is set to 'active' an attempt is made to set up the Soft PVPC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
atmInterfaceSoftPvcAddressTable	1.3.6.1.4.1.353.5.5.1.1.4		not-accessible	This table is used to configure ATM addresses at an ATM interface on this node prior to setting up Soft PVPCs or Soft PVPCs at that interface.
atmInterfaceSoftPvcAddressEntry	1.3.6.1.4.1.353.5.5.1.1.4.1		not-accessible	ATM address entry for configuring Soft PVCCs or Soft PVPCs at an ATM interface.
ATM atmInterfaceSoftPvcAddress	1.3.6.1.4.1.353.5.5.1.1.4.1.1	AtmAddr	not-accessible	Specifies the address that can be used to establish a Soft PVCC or Soft PVPC to this interface.
ROW atmInterfaceSoftPvcAddressRowStatus	1.3.6.1.4.1.353.5.5.1.1.4.1.2	RowStatus	read-write	Used to create and delete an ATM address at this interface for setting up Soft PVCCs or Soft PVPCs.
atmCurrentlyFailingSoftPVccTable	1.3.6.1.4.1.353.5.5.1.1.5		not-accessible	A table indicating all Soft Permanent Virtual Channel Connections (Soft PVCCs) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVccEntry	1.3.6.1.4.1.353.5.5.1.1.5.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
TIM atmCurrentlyFailingSoftPVccTimeStamp	1.3.6.1.4.1.353.5.5.1.1.5.1.1	TimeStamp	read-only	The time at which this Soft PVCC began to fail.
atmCurrentlyFailingSoftPVpcTable	1.3.6.1.4.1.353.5.5.1.1.6		not-accessible	A table indicating all Soft Permanent Virtual Path Connections (Soft PVPCs) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVpcEntry	1.3.6.1.4.1.353.5.5.1.1.6.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
TIM atmCurrentlyFailingSoftPVpcTimeStamp	1.3.6.1.4.1.353.5.5.1.1.6.1.1	TimeStamp	read-only	The time at which this Soft PVPC began to fail.
atmSoftPvcMIBTraps	1.3.6.1.4.1.353.5.5.1.2
atmSoftPvcTraps	1.3.6.1.4.1.353.5.5.1.2.1
atmSoftPvcTrapsPrefix	1.3.6.1.4.1.353.5.5.1.2.1.0
NTF atmSoftPvcCallFailuresTrap	1.3.6.1.4.1.353.5.5.1.2.1.0.1			A notification indicating that one or more series of call attempts in trying to establish a Soft PVPC or Soft PVCC have failed since the last atmSoftPvcCallFailureTrap was sent. If this trap has not been sent for the last atmSoftPvcNotificationInterval, then it will be sent on the next increment of atmSoftPvcCallFailures.
atmSoftPvcMIBConformance	1.3.6.1.4.1.353.5.5.1.3
atmSoftPvcMIBCompliances	1.3.6.1.4.1.353.5.5.1.3.1
atmSoftPvcMIBCompliance	1.3.6.1.4.1.353.5.5.1.3.1.1
atmSoftPvcMIBGroups	1.3.6.1.4.1.353.5.5.1.3.2
atmSoftPvcBaseMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.1
atmSoftPvcVccMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.2
atmSoftPvcVpcMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.3
atmSoftPvcAddressMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.4
atmCurrentlyFailingSoftPVccMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.5
atmCurrentlyFailingSoftPVpcMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.6

AtmAddr (3)
ATM atmInterfaceSoftPvcAddress	1.3.6.1.4.1.353.5.5.1.1.4.1.1	AtmAddr	not-accessible	Specifies the address that can be used to establish a Soft PVCC or Soft PVPC to this interface.
ATM atmSoftPVccTargetAddress	1.3.6.1.4.1.353.5.5.1.1.2.1.2	AtmAddr	read-write	The target ATM Address of this Soft PVCC. If no address is supplied, no attempts to establish the Soft PVCC are initiated.
ATM atmSoftPVpcTargetAddress	1.3.6.1.4.1.353.5.5.1.1.3.1.2	AtmAddr	read-write	The target ATM Address of this Soft PVPC. If no address is supplied, no attempts to establish the Soft PVPC are initiated.
Counter32 (1)
C32 atmSoftPvcCallFailures	1.3.6.1.4.1.353.5.5.1.1.1.2	Counter32	read-only	The number of times a series of call attempts has failed to establish a Soft PVCC or Soft PVPC. The number of call attempts in a series is determined by atmSoftPVccRetryThreshold or atmSoftPVpcRetryThreshold, respectively.
Gauge32 (4)
G32 atmSoftPVccRetryFailures	1.3.6.1.4.1.353.5.5.1.1.2.1.13	Gauge32	read-only	Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVCC is restarted.
G32 atmSoftPvcCurrentlyFailingSoftPVccs	1.3.6.1.4.1.353.5.5.1.1.1.3	Gauge32	read-only	The current number of Soft PVCCs for which there is an active row in the atmSoftPVccTable having an atmSoftPVccOperStatus with a value other than 'connected'.
G32 atmSoftPvcCurrentlyFailingSoftPVpcs	1.3.6.1.4.1.353.5.5.1.1.1.4	Gauge32	read-only	The current number of Soft PVPCs for which there is an active row in the atmSoftPVpcTable having an atmSoftPVpcOperStatus with a value other than 'connected'.
G32 atmSoftPVpcRetryFailures	1.3.6.1.4.1.353.5.5.1.1.3.1.12	Gauge32	read-only	Indicates how many attempts to establish the connection have failed. This count is reset whenever a connection is successfully established or the Soft PVPC is restarted.
INTEGER (22)
INT atmSoftPVccLastReleaseCause	1.3.6.1.4.1.353.5.5.1.1.2.1.6	INTEGER	read-only	Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC. Indicates the reason for the Release.
INT atmSoftPVccLeafReference	1.3.6.1.4.1.353.5.5.1.1.2.1.1	INTEGER	not-accessible	An arbitrary integer which, in the case of the source VCL having an atmVclCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVCC. If the atmVclCastType is not 'p2mpRoot' the value 1 shall be used.
INT atmSoftPVccOperStatus	1.3.6.1.4.1.353.5.5.1.1.2.1.8	INTEGER	read-only	Describes the status of the Soft PVCC. Valid values are: other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
INT atmSoftPVccRestart	1.3.6.1.4.1.353.5.5.1.1.2.1.9	INTEGER	read-write	When the value is set to 'restart' the Soft PVCC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVccOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVccRetryFailures object is cleared When the value is set to 'noop' no operation is performed. When read, the value 'noop' is returned.
INT atmSoftPVccRetryInterval	1.3.6.1.4.1.353.5.5.1.1.2.1.10	INTEGER	read-write	Defines the period to wait before attempting to establish the Soft PVCC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
INT atmSoftPVccRetryLimit	1.3.6.1.4.1.353.5.5.1.1.2.1.14	INTEGER	read-write	Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVccRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
INT atmSoftPVccRetryThreshold	1.3.6.1.4.1.353.5.5.1.1.2.1.12	INTEGER	read-write	Indicates the number of consecutive call setup attempts for the same Soft PVCC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVCC.
INT atmSoftPVccRetryTimer	1.3.6.1.4.1.353.5.5.1.1.2.1.11	INTEGER	read-only	Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVCC. When the timer is not running, the value zero shall be returned.
INT atmSoftPVccTargetSelectType	1.3.6.1.4.1.353.5.5.1.1.2.1.3	INTEGER	read-write	Indicates whether the target VPI/VCI values are to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI/VCI values. In such a case, once the Soft PVCC atmSoftPVccOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI/VCI values will continue to be used even if the connection is subsequently torn down and re-established. The VPI/VCI values chosen will be available for reading in atmSoftPVccTargetVpi and atmSoftPVccTargetVci. If the value 'required' is specified, then values must be supplied for objects atmSoftPVccTargetVpi and atmSoftPVccTargetVci prior to activation of the row. These values are then to be used at the destination.
INT atmSoftPVccTargetVci	1.3.6.1.4.1.353.5.5.1.1.2.1.5	INTEGER	read-write	The VCI value of the VCL used at the target interface. This value must be filled in when the atmSoftPVccTargetSelectType is set to 'required'.This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
INT atmSoftPVccTargetVpi	1.3.6.1.4.1.353.5.5.1.1.2.1.4	INTEGER	read-write	The VPI value of the VCL used at the target interface. This value is not relevant when the value of atmSoftPVccTargetSelectType is 'any'.
INT atmSoftPvcNotificationInterval	1.3.6.1.4.1.353.5.5.1.1.1.5	INTEGER	read-write	The minimum interval between the sending of atmSoftPvcCallFailuresTrap notifications.
INT atmSoftPVpcLastReleaseCause	1.3.6.1.4.1.353.5.5.1.1.3.1.5	INTEGER	read-only	Value of the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC. Indicates the reason for the Release.
INT atmSoftPVpcLeafReference	1.3.6.1.4.1.353.5.5.1.1.3.1.1	INTEGER	not-accessible	An arbitrary integer which, in the case of the source VPL having a atmVplCastType of 'p2mpRoot', serves to distinguish between the multiple leaves attached to a root of a point-to-multipoint Soft PVPC. If the atmVplCastType is not 'p2mpRoot', the value 1 shall be used.
INT atmSoftPVpcOperStatus	1.3.6.1.4.1.353.5.5.1.1.3.1.7	INTEGER	read-only	Describes the status of the Soft PVPC. other - none of the types specified below establishmentInProgress - connection or party is not operational, but setup or add party attempts are ongoing connected - connection or party is currently operational retriesExhausted - retry limit has been reached and setup or add party attempts have ceased noAddressSupplied - no remote address has been configured, so no setup or add party attempts are initiated lowerLayerDown - underlying ATM interface is not operational When the row is not 'active', the value of this object is 'other'.
INT atmSoftPVpcRestart	1.3.6.1.4.1.353.5.5.1.1.3.1.8	INTEGER	read-write	When the value is set to 'restart', the Soft PVPC is released if necessary and a new setup procedure is begun. As a result of this action, the atmSoftPVpcOperStatus object transitions to 'establishmentInProgress' (if not already in this state) and the atmSoftPVpcRetryFailures object is cleared. When the value is set to 'noop', no operation is performed. When read, the value 'noop' is returned.
INT atmSoftPVpcRetryInterval	1.3.6.1.4.1.353.5.5.1.1.3.1.9	INTEGER	read-write	Defines the period to wait before attempting to establish the Soft PVPC after the first failed call attempt. The time to wait between subsequent call attempts may differ to implement a backoff scheme. Zero represents an infinite interval indicating no retries.
INT atmSoftPVpcRetryLimit	1.3.6.1.4.1.353.5.5.1.1.3.1.13	INTEGER	read-write	Sets a maximum limit on how many consecutive unsuccessful call setup attempts can be made before stopping the attempt to set up the connection. If this limit is reached then management action will be required (e.g. setting atmSoftPVpcRestart to 'restart') to initiate a new attempt to establish the connection. A value of zero indicates no limit - the attempts will continue until successful.
INT atmSoftPVpcRetryThreshold	1.3.6.1.4.1.353.5.5.1.1.3.1.11	INTEGER	read-write	Indicates the number of consecutive call setup attempts for the same Soft PVPC which need to fail before the atmSoftPvcCallFailures object is incremented. A value of zero indicates that an infinite number of call attempts are required to increment the atmSoftPvcCallFailures object and thus disables alarms for the Soft PVPC.
INT atmSoftPVpcRetryTimer	1.3.6.1.4.1.353.5.5.1.1.3.1.10	INTEGER	read-only	Indicates the current value of the retry timer for this connection. When the value reaches zero an attempt will be made to establish the Soft PVPC. When the timer is not running, the value zero shall be returned.
INT atmSoftPVpcTargetSelectType	1.3.6.1.4.1.353.5.5.1.1.3.1.3	INTEGER	read-write	Indicates whether the target VPI value is to be used at the destination. If the value 'any' is specified, the destination switch will choose the VPI value. In such a case, once the Soft PVPC atmSoftPVpcOperStatus value is 'connected', the value of this object changes to 'required', such that the same VPI value will continue to be used even if the connection is subsequently torn down and re-established. The VPI value chosen will be available for reading in atmSoftPVpcTargetVpi. If the value 'required' is specified, then a value must be supplied for object atmSoftPVpcTargetVpi prior to activation of the row. This value is then to be used at the destination.
INT atmSoftPVpcTargetVpi	1.3.6.1.4.1.353.5.5.1.1.3.1.4	INTEGER	read-write	The VPI value of the VPL used at the target interface. This value must be filled in when the atmSoftPVpcTargetSelectType is set to 'required'. This value is not relevant when the value of atmSoftPVpcTargetSelectType is 'any'.
OCTET STRING (2)
OCT atmSoftPVccLastReleaseDiagnostic	1.3.6.1.4.1.353.5.5.1.1.2.1.7	OCTET STRING	read-only	Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVCC.
OCT atmSoftPVpcLastReleaseDiagnostic	1.3.6.1.4.1.353.5.5.1.1.3.1.6	OCTET STRING	read-only	Value of the first 8 bytes of diagnostic information from the Cause field of the Cause Information Element in the last RELEASE signalling message received for this Soft PVPC.
RowStatus (3)
ROW atmInterfaceSoftPvcAddressRowStatus	1.3.6.1.4.1.353.5.5.1.1.4.1.2	RowStatus	read-write	Used to create and delete an ATM address at this interface for setting up Soft PVCCs or Soft PVPCs.
ROW atmSoftPVccRowStatus	1.3.6.1.4.1.353.5.5.1.1.2.1.15	RowStatus	read-write	Used to create and delete a Soft PVCC. When this object is set to 'active' an attempt is made to set up the Soft PVCC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
ROW atmSoftPVpcRowStatus	1.3.6.1.4.1.353.5.5.1.1.3.1.14	RowStatus	read-write	Used to create and delete a Soft PVPC. When this object is set to 'active' an attempt is made to set up the Soft PVPC. When this object has the value 'active' and is set to another value, any set-up or connection in-progress is released.
TimeStamp (2)
TIM atmCurrentlyFailingSoftPVccTimeStamp	1.3.6.1.4.1.353.5.5.1.1.5.1.1	TimeStamp	read-only	The time at which this Soft PVCC began to fail.
TIM atmCurrentlyFailingSoftPVpcTimeStamp	1.3.6.1.4.1.353.5.5.1.1.6.1.1	TimeStamp	read-only	The time at which this Soft PVPC began to fail.
TruthValue (1)
T/F atmSoftPvcCallFailuresTrapEnable	1.3.6.1.4.1.353.5.5.1.1.1.1	TruthValue	read-write	Allows the generation of traps in response to call failures. By default, this object is set to 'false'.
No type (30)
atmCurrentlyFailingSoftPVccEntry	1.3.6.1.4.1.353.5.5.1.1.5.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVccMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.5
atmCurrentlyFailingSoftPVccTable	1.3.6.1.4.1.353.5.5.1.1.5		not-accessible	A table indicating all Soft Permanent Virtual Channel Connections (Soft PVCCs) for which the atmSoftPVccRowStatus is 'active' and the atmSoftPVccOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVpcEntry	1.3.6.1.4.1.353.5.5.1.1.6.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
atmCurrentlyFailingSoftPVpcMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.6
atmCurrentlyFailingSoftPVpcTable	1.3.6.1.4.1.353.5.5.1.1.6		not-accessible	A table indicating all Soft Permanent Virtual Path Connections (Soft PVPCs) for which the atmSoftPVpcRowStatus is 'active' and the atmSoftPVpcOperStatus is other than 'connected'.
atmForum	1.3.6.1.4.1.353
atmForumNetworkManagement	1.3.6.1.4.1.353.5
atmfSoftPvc	1.3.6.1.4.1.353.5.5
atmInterfaceSoftPvcAddressEntry	1.3.6.1.4.1.353.5.5.1.1.4.1		not-accessible	ATM address entry for configuring Soft PVCCs or Soft PVPCs at an ATM interface.
atmInterfaceSoftPvcAddressTable	1.3.6.1.4.1.353.5.5.1.1.4		not-accessible	This table is used to configure ATM addresses at an ATM interface on this node prior to setting up Soft PVPCs or Soft PVPCs at that interface.
atmSoftPvcAddressMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.4
atmSoftPvcBaseGroup	1.3.6.1.4.1.353.5.5.1.1.1
atmSoftPvcBaseMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.1
NTF atmSoftPvcCallFailuresTrap	1.3.6.1.4.1.353.5.5.1.2.1.0.1			A notification indicating that one or more series of call attempts in trying to establish a Soft PVPC or Soft PVCC have failed since the last atmSoftPvcCallFailureTrap was sent. If this trap has not been sent for the last atmSoftPvcNotificationInterval, then it will be sent on the next increment of atmSoftPvcCallFailures.
atmSoftPVccEntry	1.3.6.1.4.1.353.5.5.1.1.2.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Channel Connection (Soft PVCC) originating at a switch interface. A Soft PVCC is a VCC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVclTable must be created, defining a VCL on the source interface, prior to creating an atmSoftPVccEntry row. The row in the atmVclTable must be active prior to activating the atmSoftPVccEntry row. The contents of this table reflect only the characteristics unique to a Soft PVCC. The traffic parameters are defined in the VCL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVCCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVccRowStatus) can be set while the row is active. At the destination, the VCL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVclVpi, and atmVclVci specified in the index clause of this entry serves to identify the VCL on the source interface. The atmSoftPVccLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVCC.
atmSoftPVccTable	1.3.6.1.4.1.353.5.5.1.1.2		not-accessible	The (conceptual) table used to manage Soft Permanent Virtual Channel Connections (Soft PVCCs). The Soft PVCC table is applicable only to switches.
atmSoftPvcMIB	1.3.6.1.4.1.353.5.5.1
atmSoftPvcMIBCompliance	1.3.6.1.4.1.353.5.5.1.3.1.1
atmSoftPvcMIBCompliances	1.3.6.1.4.1.353.5.5.1.3.1
atmSoftPvcMIBConformance	1.3.6.1.4.1.353.5.5.1.3
atmSoftPvcMIBGroups	1.3.6.1.4.1.353.5.5.1.3.2
atmSoftPvcMIBObjects	1.3.6.1.4.1.353.5.5.1.1
atmSoftPvcMIBTraps	1.3.6.1.4.1.353.5.5.1.2
atmSoftPvcTraps	1.3.6.1.4.1.353.5.5.1.2.1
atmSoftPvcTrapsPrefix	1.3.6.1.4.1.353.5.5.1.2.1.0
atmSoftPvcVccMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.2
atmSoftPvcVpcMIBGroup	1.3.6.1.4.1.353.5.5.1.3.2.3
atmSoftPVpcEntry	1.3.6.1.4.1.353.5.5.1.1.3.1		not-accessible	Each entry in this table represents a Soft Permanent Virtual Path Connection (Soft PVPC) originating at a switch interface. A Soft PVPC is a VPC that is: - provisioned at the originating (source) interface of the connection - established by signalling procedures across a network to a destination interface. A row in the atmVplTable must be created, defining a VPL on the source interface, prior to creating an atmSoftPVpcEntry row. The row in the atmVplTable must be active prior to activating the atmSoftPVpcEntry row. The contents of this table reflect only the characteristics unique to a Soft PVPC. The traffic parameters are defined in the VPL row for the source interface, as specified in the ATOMMIB (RFC1695) and the forthcoming addition, the Supplemental ATOMMIB. Note that the atmSigDescrParamTable contains some objects such as the AAL parameters, Broadband high layer information, and Broadband low layer information elements which are used to carry end-to-end information. For this reason, these objects are not relevant to Soft PVPCs. When a row is made active, an attempt is made to set up a switched connection to an interface at the destination switch. No objects (other than atmSoftPVpcRowStatus) can be set while the row is active. At the destination, the VPL may be defined (but not cross-connected) prior to arrival of the Setup request. The combination of ifIndex, atmVplVpi specified in the index clause of this entry serves to identify the VPL on the source interface. The atmSoftPVpcLeafReference object aids in distinguishing between leaves of a point-to-multipoint Soft PVPC.
atmSoftPVpcTable	1.3.6.1.4.1.353.5.5.1.1.3		not-accessible	The (conceptual) table used to manage Soft Permanent Virtual Path Connections (Soft PVPCs) The Soft PVPC table is applicable only to switches.

RFC description

IETF RFC 3289 MIB for managing Soft Permanent Virtual Circuits (Soft PVCs) in ATM networks.

Start monitoring ATM switches/routers supporting Soft PVC with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ATM-SOFT-PVC-MIB

This MIB depends on

Related MIBs

What Is ATM-SOFT-PVC-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description