ASCEND-MIBT1NET-MIB

All MIBs › ASCEND-MIBT1NET-MIB

Category: Network Interfaces, Vendor: Ascend/Lucent

Description: Manages T1 WAN interface configuration, framing, and performance statistics on Ascend equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ASCEND-MIBT1NET-MIB?

ASCEND-MIBT1NET-MIB is a proprietary Ascend module managing T1 WAN interface configuration, framing, and performance statistics on Ascend access equipment. It exposes configuration for T1 line parameters (framing format, line coding) alongside performance counters such as errored seconds and alarm conditions. Its monitoring role is squarely hardware/line status: detecting T1 line faults (loss of signal, framing errors, alarm indication signal) that indicate a failing WAN trunk or line card before they cause a full outage. It parallels the IETF DS1-MIB (RFC 3895 and predecessors) in scope, though implemented as an Ascend-specific object tree. It is deployed on Ascend dial access and DSLAM equipment using T1 circuits as WAN trunks or telephony feeds. Engineers can download the ASCEND-MIBT1NET-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ASCEND-MIBT1NET-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ascend dial access/DSLAM equipment with T1 trunks

Monitoring Examples

sample_objects was empty for this module, so the following is inferred from its declared purpose rather than confirmed object names. An administrator would poll T1 line entries for errored-second counts and alarm state, treating a line reporting a persistent alarm indication signal as a hardware or wiring fault requiring immediate attention. This is typically monitored alongside call-switching and resource MIBs to correlate trunk-level faults with call failures on the platform.

What Can Be Monitored

T1 line errored-second counts
T1 alarm/loss-of-signal status
line framing/coding configuration

Imported Objects

From ASCEND-MIB

configuration

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
mibt1NetworkProfile	1.3.6.1.4.1.529.23.127
mibt1NetworkProfile_LineInterface_ChannelConfigEntry	1.3.6.1.4.1.529.23.127.2.1		not-accessible	A mibt1NetworkProfile__line_interface__channel_config entry containing objects that maps to the parameters of mibt1NetworkProfile__line_interface__channel_config profile.
mibt1NetworkProfile_LineInterface_ChannelConfigTable	1.3.6.1.4.1.529.23.127.2		not-accessible	A list of mibt1NetworkProfile__line_interface__channel_config profile entries.
mibt1NetworkProfileEntry	1.3.6.1.4.1.529.23.127.1.1		not-accessible	A mibt1NetworkProfile entry containing objects that maps to the parameters of mibt1NetworkProfile profile.
mibt1NetworkProfileTable	1.3.6.1.4.1.529.23.127.1		not-accessible	A list of mibt1NetworkProfile profile entries.
mibt1NetworkProfileV1	1.3.6.1.4.1.529.23.126
mibt1NetworkProfileV1_LineInterface_ChannelConfigEntry	1.3.6.1.4.1.529.23.126.3.1		not-accessible	A mibt1NetworkProfile_v1__line_interface__channel_config entry containing objects that maps to the parameters of mibt1NetworkProfile_v1__line_interface__channel_config profile.
mibt1NetworkProfileV1_LineInterface_ChannelConfigTable	1.3.6.1.4.1.529.23.126.3		not-accessible	A list of mibt1NetworkProfile_v1__line_interface__channel_config profile entries.
mibt1NetworkProfileV1_LineInterfaceEntry	1.3.6.1.4.1.529.23.126.2.1		not-accessible	A mibt1NetworkProfile_v1__line_interface entry containing objects that maps to the parameters of mibt1NetworkProfile_v1__line_interface profile.
mibt1NetworkProfileV1_LineInterfaceTable	1.3.6.1.4.1.529.23.126.2		not-accessible	A list of mibt1NetworkProfile_v1__line_interface profile entries.
mibt1NetworkProfileV1Entry	1.3.6.1.4.1.529.23.126.1.1		not-accessible	A mibt1NetworkProfile_v1 entry containing objects that maps to the parameters of mibt1NetworkProfile_v1 profile.
mibt1NetworkProfileV1Table	1.3.6.1.4.1.529.23.126.1		not-accessible	A list of mibt1NetworkProfile_v1 profile entries.
INT t1NetworkProfile_Action_o	1.3.6.1.4.1.529.23.127.1.1.81	INTEGER	read-write
INT t1NetworkProfile_BackToBack	1.3.6.1.4.1.529.23.127.1.1.79	INTEGER	read-write	Indicates whether the Multiband is connected back-to-back to another Muliband, rather than a DPNSS PBX. If this field is TRUE, than we don't need to disable receiving interrupts when too many are coming in beyond our processing power. NOTE: GPT's iSDX keeps re-transmitting a frame at 8 ms intervals until it receives an acknowledgement.
INT t1NetworkProfile_ChannelUsage	1.3.6.1.4.1.529.23.127.1.1.80	INTEGER	read-write	This is the use of the first T1 interface.
INT t1NetworkProfile_Item_o	1.3.6.1.4.1.529.23.127.1.1.3	INTEGER	read-only
STR t1NetworkProfile_LineInterface_AddDigitString	1.3.6.1.4.1.529.23.127.1.1.23	DisplayString	read-write	String of digits to prepend to phone number received from PBX.
INT t1NetworkProfile_LineInterface_AnswerDelay	1.3.6.1.4.1.529.23.127.1.1.50	INTEGER	read-write	Number of milliseconds to wait before answering an incoming R2 call.
INT t1NetworkProfile_LineInterface_AnswerService	1.3.6.1.4.1.529.23.127.1.1.26	INTEGER	read-write	The switched service type (or none) that is used for routing network calls to the pbx.
INT t1NetworkProfile_LineInterface_CallByCall	1.3.6.1.4.1.529.23.127.1.1.24	INTEGER	read-write	Call-by-call value to set when routing calls from PBX to network.
INT t1NetworkProfile_LineInterface_CallerId	1.3.6.1.4.1.529.23.127.1.1.51	INTEGER	read-write	TRUE if the caller Id is enabled, otherwise FALSE.
INT t1NetworkProfile_LineInterface_CauseCodeVerificationEnable	1.3.6.1.4.1.529.23.127.1.1.88	INTEGER	read-write	When set to yes, the received CAUSE value will be verified to ensure that cause is defined for the configured switch type. If the switch does not support the cause code, then INVALID ELEM CONTENTS (Cause value 100) will be used for generating PSTN Q931 response. When set to no, the received CAUSE value will be used to generate the PSTN Q931 response.
INT t1NetworkProfile_LineInterface_ChannelConfig_ChanGroup	1.3.6.1.4.1.529.23.127.2.1.15	INTEGER	read-write	A number that identifies the channel-group to which this channel belongs.
INT t1NetworkProfile_LineInterface_ChannelConfig_ChannelUsage	1.3.6.1.4.1.529.23.127.2.1.5	INTEGER	read-write	The usage for this specific channel. May be different than the usage for the line, e.g. a nailed channel (clear 64) in a line otherwise used for switched calls.
INT t1NetworkProfile_LineInterface_ChannelConfig_DestChanGroup	1.3.6.1.4.1.529.23.127.2.1.16	INTEGER	read-write	A number that identifies the channel-group to which any incoming calls on this channel will be directed.
INT t1NetworkProfile_LineInterface_ChannelConfig_DialPlanNumber	1.3.6.1.4.1.529.23.127.2.1.17	INTEGER	read-write	A number that identifies the dial plan from the dial plan menu.
INT t1NetworkProfile_LineInterface_ChannelConfig_IdlePattern	1.3.6.1.4.1.529.23.127.2.1.19	INTEGER	read-write	The idle pattern is the data pattern sent on a channel when it is idle. The idle pattern can be any value from 0(0x00) to 255(0xff)
INT t1NetworkProfile_LineInterface_ChannelConfig_Index_o	1.3.6.1.4.1.529.23.127.2.1.4	INTEGER	read-only
INT t1NetworkProfile_LineInterface_ChannelConfig_Item_o	1.3.6.1.4.1.529.23.127.2.1.3	INTEGER	read-only
INT t1NetworkProfile_LineInterface_ChannelConfig_NailedGroup	1.3.6.1.4.1.529.23.127.2.1.14	INTEGER	read-write	A number that identifies the set of channels that makes up a nailed group.
INT t1NetworkProfile_LineInterface_ChannelConfig_NumberOfDialPlanSelectDigits	1.3.6.1.4.1.529.23.127.2.1.18	INTEGER	read-write	The number of leading digits in the incoming phone number to use for selecting the Dial Plan.
STR t1NetworkProfile_LineInterface_ChannelConfig_PhoneNumber	1.3.6.1.4.1.529.23.127.2.1.7	DisplayString	read-write	The phone number of this channel. This is the number sent to the far end in an inverse multiplexed call when instructing the far end to add more bandwidth. The number should contain the minimum number of digits to identify the channel. If the channel is part of a hunt group, the phone number should be blank.
INT t1NetworkProfile_LineInterface_ChannelConfig_RoutePort_RelativePortNumber_RelativePortNumber	1.3.6.1.4.1.529.23.127.2.1.10	INTEGER	read-write
INT t1NetworkProfile_LineInterface_ChannelConfig_RoutePort_SlotNumber_ShelfNumber	1.3.6.1.4.1.529.23.127.2.1.9	INTEGER	read-write	TNT is a multi shelf system. To minimise the changes required to existing code the shelf number is added to this structure as it will almost always be needed when a slot number is needed.
INT t1NetworkProfile_LineInterface_ChannelConfig_RoutePort_SlotNumber_SlotNumber	1.3.6.1.4.1.529.23.127.2.1.8	INTEGER	read-write
INT t1NetworkProfile_LineInterface_ChannelConfig_Shelf_o	1.3.6.1.4.1.529.23.127.2.1.1	INTEGER	read-only
INT t1NetworkProfile_LineInterface_ChannelConfig_Slot_o	1.3.6.1.4.1.529.23.127.2.1.2	INTEGER	read-only
INT t1NetworkProfile_LineInterface_ChannelConfig_TrunkGroup	1.3.6.1.4.1.529.23.127.2.1.6	INTEGER	read-write	The trunk group assigned to this channel.
INT t1NetworkProfile_LineInterface_ClockPriority	1.3.6.1.4.1.529.23.127.1.1.13	INTEGER	read-write	Clock priority assigned to the T1 line. Used to select particular lines as clock source.
INT t1NetworkProfile_LineInterface_ClockSource	1.3.6.1.4.1.529.23.127.1.1.12	INTEGER	read-write
INT t1NetworkProfile_LineInterface_CollectIncomingDigits	1.3.6.1.4.1.529.23.127.1.1.62	INTEGER	read-write	TRUE collect incoming called/calling digits, otherwise FALSE.
INT t1NetworkProfile_LineInterface_DataSense	1.3.6.1.4.1.529.23.127.1.1.28	INTEGER	read-write	D-channel normal or inverted data. Currently unused (normal data is always selected.
INT t1NetworkProfile_LineInterface_DefaultCallType	1.3.6.1.4.1.529.23.127.1.1.17	INTEGER	read-write	Specify the default call-type for incoming calls, for purposes of call routing and signalling.
INT t1NetworkProfile_LineInterface_DeleteDigits	1.3.6.1.4.1.529.23.127.1.1.22	INTEGER	read-write	Number of digits to delete from numbers received from a PBX.
INT t1NetworkProfile_LineInterface_DownTransDelay	1.3.6.1.4.1.529.23.127.1.1.84	INTEGER	read-write	To control the delay in line state transition from up to down when loss of carrier is detected. Each unit of this value is equal to .1 seconds of Delay in UP to DOWN transition.
INT t1NetworkProfile_LineInterface_Enabled	1.3.6.1.4.1.529.23.127.1.1.8	INTEGER	read-write	TRUE if the line is enabled, otherwise FALSE.
INT t1NetworkProfile_LineInterface_Encoding	1.3.6.1.4.1.529.23.127.1.1.11	INTEGER	read-write	The layer 1 line encoding used for the physical link(s).
INT t1NetworkProfile_LineInterface_FirstDs0	1.3.6.1.4.1.529.23.127.1.1.69	INTEGER	read-write	When using fractional T1/E1 the first DS0 used. Default is 1
INT t1NetworkProfile_LineInterface_FrameType	1.3.6.1.4.1.529.23.127.1.1.10	INTEGER	read-write	The super-framing mode that is used on the physical link(s).
INT t1NetworkProfile_LineInterface_FrontEndType	1.3.6.1.4.1.529.23.127.1.1.31	INTEGER	read-write	The front end type (CSU/DSX) of the T1 transceiver.
INT t1NetworkProfile_LineInterface_Gr303Ds1Id	1.3.6.1.4.1.529.23.127.1.1.77	INTEGER	read-write	For GR303 lines: The logical DS1 id.
INT t1NetworkProfile_LineInterface_Gr303GroupId	1.3.6.1.4.1.529.23.127.1.1.76	INTEGER	read-write	For GR303 lines: the interface group id.
INT t1NetworkProfile_LineInterface_Gr303Mode	1.3.6.1.4.1.529.23.127.1.1.75	INTEGER	read-write	GR-303 Mode.
INT t1NetworkProfile_LineInterface_GroupBAnswerSignal	1.3.6.1.4.1.529.23.127.1.1.44	INTEGER	read-write	The group B signal to send prior to answering a call.
INT t1NetworkProfile_LineInterface_GroupBBusySignal	1.3.6.1.4.1.529.23.127.1.1.45	INTEGER	read-write	The group B signal to send to reject a call.
INT t1NetworkProfile_LineInterface_GroupBCollectSignal	1.3.6.1.4.1.529.23.127.1.1.47	INTEGER	read-write	The group B signal to send to answer/reject a collect call.
INT t1NetworkProfile_LineInterface_GroupBNoChargeSignal	1.3.6.1.4.1.529.23.127.1.1.82	INTEGER	read-write	The group B signal to send if subscriber line is idle / no charge
INT t1NetworkProfile_LineInterface_GroupBNoMatchSignal	1.3.6.1.4.1.529.23.127.1.1.46	INTEGER	read-write	The group B signal to send to reject a call with invalid call number.
INT t1NetworkProfile_LineInterface_GroupIiSignal	1.3.6.1.4.1.529.23.127.1.1.48	INTEGER	read-write	The group II signal to send after sending all address digits.
STR t1NetworkProfile_LineInterface_HuntGrpPhoneNumber1	1.3.6.1.4.1.529.23.127.1.1.56	DisplayString	read-write	The hunt group phone number associated with this line. Manually entered field which is read-write accessible via SNMP.
STR t1NetworkProfile_LineInterface_HuntGrpPhoneNumber2	1.3.6.1.4.1.529.23.127.1.1.57	DisplayString	read-write	The hunt group phone number associated with this line. Manually entered field which is read-write accessible via SNMP.
STR t1NetworkProfile_LineInterface_HuntGrpPhoneNumber3	1.3.6.1.4.1.529.23.127.1.1.58	DisplayString	read-write	The hunt group phone number associated with this line. Manually entered field which is read-write accessible via SNMP.
INT t1NetworkProfile_LineInterface_IdleMode	1.3.6.1.4.1.529.23.127.1.1.29	INTEGER	read-write	D-channel mark or flag idle. Currently unused (flag idle is always selected.
INT t1NetworkProfile_LineInterface_IncomingCallHandling	1.3.6.1.4.1.529.23.127.1.1.21	INTEGER	read-write	This parameter is used to determine the type of processing required for incoming calls from this line.
INT t1NetworkProfile_LineInterface_InputSampleCount	1.3.6.1.4.1.529.23.127.1.1.49	INTEGER	read-write	The number of Goertzel input samples (each Goertzel sample is of length N=205) to compute in order to decode DTMF tones, the more samples, the more acccurate the detection result
INT t1NetworkProfile_LineInterface_IsdnEmulationSide	1.3.6.1.4.1.529.23.127.1.1.15	INTEGER	read-write	Side the line will emulate: TE (user), or NT (network).
INT t1NetworkProfile_LineInterface_LastDs0	1.3.6.1.4.1.529.23.127.1.1.70	INTEGER	read-write	When using fractional T1/E1 the last DS0 used. Default is 24
INT t1NetworkProfile_LineInterface_Layer2End	1.3.6.1.4.1.529.23.127.1.1.39	INTEGER	read-write	This parameter is used to determine the address to send when two PBXs are connected back-to-back; one side must act as an ET, and the other side acts as a PBX. If a-side, layer 2 acts as ET.
INT t1NetworkProfile_LineInterface_Layer3End	1.3.6.1.4.1.529.23.127.1.1.38	INTEGER	read-write	If x-side, layer 3 favors outgoing call when a call collision occurs.
INT t1NetworkProfile_LineInterface_LineProvision	1.3.6.1.4.1.529.23.127.1.1.74	INTEGER	read-write	Line Provision.
INT t1NetworkProfile_LineInterface_LineSignaling	1.3.6.1.4.1.529.23.127.1.1.52	INTEGER	read-write	The line signaling of E1 line.
INT t1NetworkProfile_LineInterface_LoopAvoidance	1.3.6.1.4.1.529.23.127.1.1.41	INTEGER	read-write	Loop Avoidance; the number of transit PBXs through which a call may be routed (1 to 26 default 7).
INT t1NetworkProfile_LineInterface_MaintenanceState	1.3.6.1.4.1.529.23.127.1.1.42	INTEGER	read-write	TRUE if the line is in user-requested maintenance mode, otherwise FALSE.
INT t1NetworkProfile_LineInterface_NailedGroup	1.3.6.1.4.1.529.23.127.1.1.71	INTEGER	read-write	A number that identifies the set of lines that makes up a nailed group. 0 means this line is not part of a nailed group.
INT t1NetworkProfile_LineInterface_NetworkSpecificFacilities	1.3.6.1.4.1.529.23.127.1.1.87	INTEGER	read-write	Network Specific Facilities (NSF) value to store in the NSF IE of the outgoing Q.931 Setup message. This sets the full 8 bits of the IE.
INT t1NetworkProfile_LineInterface_NfasGroupId	1.3.6.1.4.1.529.23.127.1.1.19	INTEGER	read-write	For NFAS lines: the nfas group id. Not used with robbed bit signaling.
INT t1NetworkProfile_LineInterface_NfasId	1.3.6.1.4.1.529.23.127.1.1.20	INTEGER	read-write	For NFAS lines: the interface id. For SS7 lines when Q.931+ control protocol is used: interface id. Not used with robbed bit signaling.
INT t1NetworkProfile_LineInterface_NlValue	1.3.6.1.4.1.529.23.127.1.1.40	INTEGER	read-write	Number of re-transmissions; default to 64.
INT t1NetworkProfile_LineInterface_NumberComplete	1.3.6.1.4.1.529.23.127.1.1.43	INTEGER	read-write	The criteria for having received enough digits on an incoming R2 call. Can either be 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 13, 14, or 15 digits received, or the end-of-pulsing signal received, or time-out.
INT t1NetworkProfile_LineInterface_oCSUBuildOut	1.3.6.1.4.1.529.23.127.1.1.33	INTEGER	read-write	Line buildout value for CSU lines.
INT t1NetworkProfile_LineInterface_oDSXLineLength	1.3.6.1.4.1.529.23.127.1.1.32	INTEGER	read-write	The length of the physical T1 line (for DSX lines).
INT t1NetworkProfile_LineInterface_oFDL	1.3.6.1.4.1.529.23.127.1.1.30	INTEGER	read-write	Who's FDL are we using. Used only if frame-type is ESF - Ignored otherwise.
INT t1NetworkProfile_LineInterface_oPBXType	1.3.6.1.4.1.529.23.127.1.1.27	INTEGER	read-write	The PBX Class as defined in the enumeration above.
INT t1NetworkProfile_LineInterface_OverlapReceiving	1.3.6.1.4.1.529.23.127.1.1.34	INTEGER	read-write	TRUE if overlap receiving procedure may be used to handle incoming call, FALSE if not
STR t1NetworkProfile_LineInterface_PbxAnswerNumber	1.3.6.1.4.1.529.23.127.1.1.25	DisplayString	read-write	The answer number that is the equivalent of a port answer-number used for the network to pbx routing.
INT t1NetworkProfile_LineInterface_PriNumberingPlanId	1.3.6.1.4.1.529.23.127.1.1.60	INTEGER	read-write	PRI Called Party element's Numbering-Plan-ID value for outgoing T1-to-PRI calls.
STR t1NetworkProfile_LineInterface_PriPrefixNumber	1.3.6.1.4.1.529.23.127.1.1.35	DisplayString	read-write	The unique prefix of the PRI called party number. It is used to determine whether SETUP message contains any trailing digits when overlap receiving procedure is used to handle the incoming call. Defaults to '' to not count the trailing digits.
INT t1NetworkProfile_LineInterface_PriTypeOfNumber	1.3.6.1.4.1.529.23.127.1.1.59	INTEGER	read-write	PRI Called Party element's Type-Of-Number value for outgoing T1-to-PRI calls.
INT t1NetworkProfile_LineInterface_R1AnirDelay	1.3.6.1.4.1.529.23.127.1.1.66	INTEGER	read-write	Delay in milliseconds between receiving ST and sending ANIR signal.
INT t1NetworkProfile_LineInterface_R1AnirTimer	1.3.6.1.4.1.529.23.127.1.1.67	INTEGER	read-write	Time in milliseconds of ANIR signal.
INT t1NetworkProfile_LineInterface_R1FirstDigitTimer	1.3.6.1.4.1.529.23.127.1.1.65	INTEGER	read-write	The timer between sending KPA and receiving first Digit in R1 signaling in milliseconds.
INT t1NetworkProfile_LineInterface_R1Modified	1.3.6.1.4.1.529.23.127.1.1.68	INTEGER	read-write	Use R1 modified signaling. Default is FALSE.
INT t1NetworkProfile_LineInterface_R1UseAnir	1.3.6.1.4.1.529.23.127.1.1.64	INTEGER	read-write	TRUE if the line is to use R1 signaling ANIR (CLID), otherwise FALSE.
INT t1NetworkProfile_LineInterface_RobbedBitMode	1.3.6.1.4.1.529.23.127.1.1.16	INTEGER	read-write	Wink start, idle start, incoming wink.
INT t1NetworkProfile_LineInterface_SendDiscVal	1.3.6.1.4.1.529.23.127.1.1.55	INTEGER	read-write	Number of seconds before sending ISDN disconnect to switch. 0 means disable.
INT t1NetworkProfile_LineInterface_SignalingMode	1.3.6.1.4.1.529.23.127.1.1.14	INTEGER	read-write	Inband, ISDN, ISDN_NFAS, PBX or SS7 signaling.
INT t1NetworkProfile_LineInterface_Ss7Continuity_IncomingProcedure	1.3.6.1.4.1.529.23.127.1.1.72	INTEGER	read-write	Procedure used for incoming continuity check on this line.
INT t1NetworkProfile_LineInterface_Ss7Continuity_OutgoingProcedure	1.3.6.1.4.1.529.23.127.1.1.73	INTEGER	read-write	Procedure used for outgoing continuity check on this line.
INT t1NetworkProfile_LineInterface_StatusChangeTrapEnable	1.3.6.1.4.1.529.23.127.1.1.83	INTEGER	read-write	When set to yes, a line status change trap is sent. NOTE: when the line status change results from a higher level line status change, i.e., ds3, then no trap for the ds1 are sent. The default setting is No.
INT t1NetworkProfile_LineInterface_SuperFrameSrcLineNumber	1.3.6.1.4.1.529.23.127.1.1.61	INTEGER	read-write	The line from which the the Super-Frame sync pulse is taken. Needed by the 'Dropped&Inserted' line so that it can become synchronized to the source line.
INT t1NetworkProfile_LineInterface_SwitchType	1.3.6.1.4.1.529.23.127.1.1.18	INTEGER	read-write	The network switch type, needed for ISDN/NFAS signaling.
INT t1NetworkProfile_LineInterface_SwitchVersion	1.3.6.1.4.1.529.23.127.1.1.78	INTEGER	read-write	Switch Version.
INT t1NetworkProfile_LineInterface_T1InterDigitTimeout	1.3.6.1.4.1.529.23.127.1.1.63	INTEGER	read-write	Inter-Digit Timeout (in milliseconds) for inband T1 and E1 R2 lines.
INT t1NetworkProfile_LineInterface_T302Timer	1.3.6.1.4.1.529.23.127.1.1.37	INTEGER	read-write	Number of milliseconds to wait for additional called number information elements for an incoming call using overlap receiving procedure. Defaults to 10000.
INT t1NetworkProfile_LineInterface_Timer1CollectCall	1.3.6.1.4.1.529.23.127.1.1.53	INTEGER	read-write	Adjustable between 0 ~ 2000ms
INT t1NetworkProfile_LineInterface_Timer2CollectCall	1.3.6.1.4.1.529.23.127.1.1.54	INTEGER	read-write	Adjustable between 10 ~ 2000ms
INT t1NetworkProfile_LineInterface_TOnlineType	1.3.6.1.4.1.529.23.127.1.1.9	INTEGER	read-write	The tonline type of an e1 line.
INT t1NetworkProfile_LineInterface_TrailingDigits	1.3.6.1.4.1.529.23.127.1.1.36	INTEGER	read-write	Number of trailing digits expected from the called party number information elements of INFORMATION messages when overlap receiving procedure is used to handle the incoming call. SETUP message may contain some trailing digits in the called party number information element. Defaults to 2.
INT t1NetworkProfile_LineInterface_UpTransDelay	1.3.6.1.4.1.529.23.127.1.1.85	INTEGER	read-write	To control the delay in line state transition from down to up when carrier is detected. Each unit of this value is equal to .1 seconds of Delay in DOWN to UP transition.
STR t1NetworkProfile_Name	1.3.6.1.4.1.529.23.127.1.1.4	DisplayString	read-write	Name of DS1 line.
INT t1NetworkProfile_PhysicalAddress_ItemNumber	1.3.6.1.4.1.529.23.127.1.1.7	INTEGER	read-write	A number that specifies an addressable entity within the context of shelf and slot.
INT t1NetworkProfile_PhysicalAddress_Shelf	1.3.6.1.4.1.529.23.127.1.1.5	INTEGER	read-write	The number of the shelf that the addressed physical device resides on.
INT t1NetworkProfile_PhysicalAddress_Slot	1.3.6.1.4.1.529.23.127.1.1.6	INTEGER	read-write	The number of the slot that the addressed physical device resides on.
INT t1NetworkProfile_Shelf_o	1.3.6.1.4.1.529.23.127.1.1.1	INTEGER	read-only
INT t1NetworkProfile_Slot_o	1.3.6.1.4.1.529.23.127.1.1.2	INTEGER	read-only
INT t1NetworkProfileV1_Action_o	1.3.6.1.4.1.529.23.126.1.1.10	INTEGER	read-write
INT t1NetworkProfileV1_BackToBack	1.3.6.1.4.1.529.23.126.1.1.6	INTEGER	read-write	Indicates whether the Multiband is connected back-to-back to another Muliband, rather than a DPNSS PBX. If this field is TRUE, than we don't need to disable receiving interrupts when too many are coming in beyond our processing power. NOTE: GPT's iSDX keeps re-transmitting a frame at 8 ms intervals until it receives an acknowledgement.
STR t1NetworkProfileV1_LineInterface_AddDigitString	1.3.6.1.4.1.529.23.126.2.1.18	DisplayString	read-write	String of digits to prepend to phone number received from PBX.
INT t1NetworkProfileV1_LineInterface_AnswerDelay	1.3.6.1.4.1.529.23.126.2.1.45	INTEGER	read-write	Number of milliseconds to wait before answering an incoming R2 call.
INT t1NetworkProfileV1_LineInterface_AnswerService	1.3.6.1.4.1.529.23.126.2.1.21	INTEGER	read-write	The switched service type (or none) that is used for routing network calls to the pbx.
INT t1NetworkProfileV1_LineInterface_CallByCall	1.3.6.1.4.1.529.23.126.2.1.19	INTEGER	read-write	Call-by-call value to set when routing calls from PBX to network.
INT t1NetworkProfileV1_LineInterface_CallerId	1.3.6.1.4.1.529.23.126.2.1.46	INTEGER	read-write	TRUE if the caller Id is enabled, otherwise FALSE.
INT t1NetworkProfileV1_LineInterface_CauseCodeVerificationEnable	1.3.6.1.4.1.529.23.126.2.1.80	INTEGER	read-write	When set to yes, the received CAUSE value will be verified to ensure that cause is defined for the configured switch type. If the switch does not support the cause code, then INVALID ELEM CONTENTS (Cause value 100) will be used for generating PSTN Q931 response. When set to no, the received CAUSE value will be used to generate the PSTN Q931 response.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_ChanGroup	1.3.6.1.4.1.529.23.126.3.1.14	INTEGER	read-write	A number that identifies the channel-group to which this channel belongs.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_ChannelUsage	1.3.6.1.4.1.529.23.126.3.1.4	INTEGER	read-write	The usage for this specific channel. May be different than the usage for the line, e.g. a nailed channel (clear 64) in a line otherwise used for switched calls.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_DestChanGroup	1.3.6.1.4.1.529.23.126.3.1.15	INTEGER	read-write	A number that identifies the channel-group to which any incoming calls on this channel will be directed.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_DialPlanNumber	1.3.6.1.4.1.529.23.126.3.1.16	INTEGER	read-write	A number that identifies the dial plan from the dial plan menu.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_IdlePattern	1.3.6.1.4.1.529.23.126.3.1.18	INTEGER	read-write	The idle pattern is the data pattern sent on a channel when it is idle. The idle pattern can be any value from 0(0x00) to 255(0xff)
INT t1NetworkProfileV1_LineInterface_ChannelConfig_Index_o	1.3.6.1.4.1.529.23.126.3.1.2	INTEGER	read-only
INT t1NetworkProfileV1_LineInterface_ChannelConfig_Index1_o	1.3.6.1.4.1.529.23.126.3.1.3	INTEGER	read-only
INT t1NetworkProfileV1_LineInterface_ChannelConfig_NailedGroup	1.3.6.1.4.1.529.23.126.3.1.13	INTEGER	read-write	A number that identifies the set of channels that makes up a nailed group.
STR t1NetworkProfileV1_LineInterface_ChannelConfig_Name	1.3.6.1.4.1.529.23.126.3.1.1	DisplayString	read-only
INT t1NetworkProfileV1_LineInterface_ChannelConfig_NumberOfDialPlanSelectDigits	1.3.6.1.4.1.529.23.126.3.1.17	INTEGER	read-write	The number of leading digits in the incoming phone number to use for selecting the Dial Plan.
STR t1NetworkProfileV1_LineInterface_ChannelConfig_PhoneNumber	1.3.6.1.4.1.529.23.126.3.1.6	DisplayString	read-write	The phone number of this channel. This is the number sent to the far end in an inverse multiplexed call when instructing the far end to add more bandwidth. The number should contain the minimum number of digits to identify the channel. If the channel is part of a hunt group, the phone number should be blank.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_RoutePort_RelativePortNumber_RelativePortNumber	1.3.6.1.4.1.529.23.126.3.1.9	INTEGER	read-write
INT t1NetworkProfileV1_LineInterface_ChannelConfig_RoutePort_SlotNumber_ShelfNumber	1.3.6.1.4.1.529.23.126.3.1.8	INTEGER	read-write	TNT is a multi shelf system. To minimise the changes required to existing code the shelf number is added to this structure as it will almost always be needed when a slot number is needed.
INT t1NetworkProfileV1_LineInterface_ChannelConfig_RoutePort_SlotNumber_SlotNumber	1.3.6.1.4.1.529.23.126.3.1.7	INTEGER	read-write
INT t1NetworkProfileV1_LineInterface_ChannelConfig_TrunkGroup	1.3.6.1.4.1.529.23.126.3.1.5	INTEGER	read-write	The trunk group assigned to this channel.
INT t1NetworkProfileV1_LineInterface_ClockPriority	1.3.6.1.4.1.529.23.126.2.1.8	INTEGER	read-write	Clock priority assigned to the T1 line. Used to select particular lines as clock source.
INT t1NetworkProfileV1_LineInterface_ClockSource	1.3.6.1.4.1.529.23.126.2.1.7	INTEGER	read-write
INT t1NetworkProfileV1_LineInterface_CollectIncomingDigits	1.3.6.1.4.1.529.23.126.2.1.57	INTEGER	read-write	TRUE collect incoming called/calling digits, otherwise FALSE.
INT t1NetworkProfileV1_LineInterface_DataSense	1.3.6.1.4.1.529.23.126.2.1.23	INTEGER	read-write	D-channel normal or inverted data. Currently unused (normal data is always selected.
INT t1NetworkProfileV1_LineInterface_DefaultCallType	1.3.6.1.4.1.529.23.126.2.1.12	INTEGER	read-write	Specify the default call-type for incoming calls, for purposes of call routing and signalling.
INT t1NetworkProfileV1_LineInterface_DeleteDigits	1.3.6.1.4.1.529.23.126.2.1.17	INTEGER	read-write	Number of digits to delete from numbers received from a PBX.
INT t1NetworkProfileV1_LineInterface_DownTransDelay	1.3.6.1.4.1.529.23.126.2.1.76	INTEGER	read-write	To control the delay in line state transition from up to down when loss of carrier is detected. Each unit of this value is equal to .1 seconds of Delay in UP to DOWN transition.
INT t1NetworkProfileV1_LineInterface_Enabled	1.3.6.1.4.1.529.23.126.2.1.3	INTEGER	read-write	TRUE if the line is enabled, otherwise FALSE.
INT t1NetworkProfileV1_LineInterface_Encoding	1.3.6.1.4.1.529.23.126.2.1.6	INTEGER	read-write	The layer 1 line encoding used for the physical link(s).
INT t1NetworkProfileV1_LineInterface_FirstDs0	1.3.6.1.4.1.529.23.126.2.1.64	INTEGER	read-write	When using fractional T1/E1 the first DS0 used. Default is 1
INT t1NetworkProfileV1_LineInterface_FrameType	1.3.6.1.4.1.529.23.126.2.1.5	INTEGER	read-write	The super-framing mode that is used on the physical link(s).
INT t1NetworkProfileV1_LineInterface_FrontEndType	1.3.6.1.4.1.529.23.126.2.1.26	INTEGER	read-write	The front end type (CSU/DSX) of the T1 transceiver.
INT t1NetworkProfileV1_LineInterface_Gr303Ds1Id	1.3.6.1.4.1.529.23.126.2.1.72	INTEGER	read-write	For GR303 lines: The logical DS1 id.
INT t1NetworkProfileV1_LineInterface_Gr303GroupId	1.3.6.1.4.1.529.23.126.2.1.71	INTEGER	read-write	For GR303 lines: the interface group id.
INT t1NetworkProfileV1_LineInterface_Gr303Mode	1.3.6.1.4.1.529.23.126.2.1.70	INTEGER	read-write	GR-303 Mode.
INT t1NetworkProfileV1_LineInterface_GroupBAnswerSignal	1.3.6.1.4.1.529.23.126.2.1.39	INTEGER	read-write	The group B signal to send prior to answering a call.
INT t1NetworkProfileV1_LineInterface_GroupBBusySignal	1.3.6.1.4.1.529.23.126.2.1.40	INTEGER	read-write	The group B signal to send to reject a call.
INT t1NetworkProfileV1_LineInterface_GroupBCollectSignal	1.3.6.1.4.1.529.23.126.2.1.42	INTEGER	read-write	The group B signal to send to answer/reject a collect call.
INT t1NetworkProfileV1_LineInterface_GroupBNoChargeSignal	1.3.6.1.4.1.529.23.126.2.1.74	INTEGER	read-write	The group B signal to send if subscriber line is idle / no charge
INT t1NetworkProfileV1_LineInterface_GroupBNoMatchSignal	1.3.6.1.4.1.529.23.126.2.1.41	INTEGER	read-write	The group B signal to send to reject a call with invalid call number.
INT t1NetworkProfileV1_LineInterface_GroupIiSignal	1.3.6.1.4.1.529.23.126.2.1.43	INTEGER	read-write	The group II signal to send after sending all address digits.
STR t1NetworkProfileV1_LineInterface_HuntGrpPhoneNumber1	1.3.6.1.4.1.529.23.126.2.1.51	DisplayString	read-write	The hunt group phone number associated with this line. Manually entered field which is read-write accessible via SNMP.
STR t1NetworkProfileV1_LineInterface_HuntGrpPhoneNumber2	1.3.6.1.4.1.529.23.126.2.1.52	DisplayString	read-write	The hunt group phone number associated with this line. Manually entered field which is read-write accessible via SNMP.
STR t1NetworkProfileV1_LineInterface_HuntGrpPhoneNumber3	1.3.6.1.4.1.529.23.126.2.1.53	DisplayString	read-write	The hunt group phone number associated with this line. Manually entered field which is read-write accessible via SNMP.
INT t1NetworkProfileV1_LineInterface_IdleMode	1.3.6.1.4.1.529.23.126.2.1.24	INTEGER	read-write	D-channel mark or flag idle. Currently unused (flag idle is always selected.
INT t1NetworkProfileV1_LineInterface_IncomingCallHandling	1.3.6.1.4.1.529.23.126.2.1.16	INTEGER	read-write	This parameter is used to determine the type of processing required for incoming calls from this line.
INT t1NetworkProfileV1_LineInterface_Index_o	1.3.6.1.4.1.529.23.126.2.1.2	INTEGER	read-only
INT t1NetworkProfileV1_LineInterface_InputSampleCount	1.3.6.1.4.1.529.23.126.2.1.44	INTEGER	read-write	The number of Goertzel input samples (each Goertzel sample is of length N=205) to compute in order to decode DTMF tones, the more samples, the more acccurate the detection result
INT t1NetworkProfileV1_LineInterface_IsdnEmulationSide	1.3.6.1.4.1.529.23.126.2.1.10	INTEGER	read-write	Side the line will emulate: TE (user), or NT (network).
INT t1NetworkProfileV1_LineInterface_LastDs0	1.3.6.1.4.1.529.23.126.2.1.65	INTEGER	read-write	When using fractional T1/E1 the last DS0 used. Default is 24
INT t1NetworkProfileV1_LineInterface_Layer2End	1.3.6.1.4.1.529.23.126.2.1.34	INTEGER	read-write	This parameter is used to determine the address to send when two PBXs are connected back-to-back; one side must act as an ET, and the other side acts as a PBX. If a-side, layer 2 acts as ET.
INT t1NetworkProfileV1_LineInterface_Layer3End	1.3.6.1.4.1.529.23.126.2.1.33	INTEGER	read-write	If x-side, layer 3 favors outgoing call when a call collision occurs.
INT t1NetworkProfileV1_LineInterface_LineProvision	1.3.6.1.4.1.529.23.126.2.1.69	INTEGER	read-write	Line Provision.
INT t1NetworkProfileV1_LineInterface_LineSignaling	1.3.6.1.4.1.529.23.126.2.1.47	INTEGER	read-write	The line signaling of E1 line.
INT t1NetworkProfileV1_LineInterface_LoopAvoidance	1.3.6.1.4.1.529.23.126.2.1.36	INTEGER	read-write	Loop Avoidance; the number of transit PBXs through which a call may be routed (1 to 26 default 7).
INT t1NetworkProfileV1_LineInterface_MaintenanceState	1.3.6.1.4.1.529.23.126.2.1.37	INTEGER	read-write	TRUE if the line is in user-requested maintenance mode, otherwise FALSE.
INT t1NetworkProfileV1_LineInterface_NailedGroup	1.3.6.1.4.1.529.23.126.2.1.66	INTEGER	read-write	A number that identifies the set of lines that makes up a nailed group. 0 means this line is not part of a nailed group.
STR t1NetworkProfileV1_LineInterface_Name	1.3.6.1.4.1.529.23.126.2.1.1	DisplayString	read-only
INT t1NetworkProfileV1_LineInterface_NetworkSpecificFacilities	1.3.6.1.4.1.529.23.126.2.1.79	INTEGER	read-write	Network Specific Facilities (NSF) value to store in the NSF IE of the outgoing Q.931 Setup message. This sets the full 8 bits of the IE.
INT t1NetworkProfileV1_LineInterface_NfasGroupId	1.3.6.1.4.1.529.23.126.2.1.14	INTEGER	read-write	For NFAS lines: the nfas group id. Not used with robbed bit signaling.
INT t1NetworkProfileV1_LineInterface_NfasId	1.3.6.1.4.1.529.23.126.2.1.15	INTEGER	read-write	For NFAS lines: the interface id. For SS7 lines when Q.931+ control protocol is used: interface id. Not used with robbed bit signaling.
INT t1NetworkProfileV1_LineInterface_NlValue	1.3.6.1.4.1.529.23.126.2.1.35	INTEGER	read-write	Number of re-transmissions; default to 64.
INT t1NetworkProfileV1_LineInterface_NumberComplete	1.3.6.1.4.1.529.23.126.2.1.38	INTEGER	read-write	The criteria for having received enough digits on an incoming R2 call. Can either be 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 13, 14, or 15 digits received, or the end-of-pulsing signal received, or time-out.
INT t1NetworkProfileV1_LineInterface_oCSUBuildOut	1.3.6.1.4.1.529.23.126.2.1.28	INTEGER	read-write	Line buildout value for CSU lines.
INT t1NetworkProfileV1_LineInterface_oDSXLineLength	1.3.6.1.4.1.529.23.126.2.1.27	INTEGER	read-write	The length of the physical T1 line (for DSX lines).
INT t1NetworkProfileV1_LineInterface_oFDL	1.3.6.1.4.1.529.23.126.2.1.25	INTEGER	read-write	Who's FDL are we using. Used only if frame-type is ESF - Ignored otherwise.
INT t1NetworkProfileV1_LineInterface_oPBXType	1.3.6.1.4.1.529.23.126.2.1.22	INTEGER	read-write	The PBX Class as defined in the enumeration above.
INT t1NetworkProfileV1_LineInterface_OverlapReceiving	1.3.6.1.4.1.529.23.126.2.1.29	INTEGER	read-write	TRUE if overlap receiving procedure may be used to handle incoming call, FALSE if not
STR t1NetworkProfileV1_LineInterface_PbxAnswerNumber	1.3.6.1.4.1.529.23.126.2.1.20	DisplayString	read-write	The answer number that is the equivalent of a port answer-number used for the network to pbx routing.
INT t1NetworkProfileV1_LineInterface_PriNumberingPlanId	1.3.6.1.4.1.529.23.126.2.1.55	INTEGER	read-write	PRI Called Party element's Numbering-Plan-ID value for outgoing T1-to-PRI calls.
STR t1NetworkProfileV1_LineInterface_PriPrefixNumber	1.3.6.1.4.1.529.23.126.2.1.30	DisplayString	read-write	The unique prefix of the PRI called party number. It is used to determine whether SETUP message contains any trailing digits when overlap receiving procedure is used to handle the incoming call. Defaults to '' to not count the trailing digits.
INT t1NetworkProfileV1_LineInterface_PriTypeOfNumber	1.3.6.1.4.1.529.23.126.2.1.54	INTEGER	read-write	PRI Called Party element's Type-Of-Number value for outgoing T1-to-PRI calls.
INT t1NetworkProfileV1_LineInterface_R1AnirDelay	1.3.6.1.4.1.529.23.126.2.1.61	INTEGER	read-write	Delay in milliseconds between receiving ST and sending ANIR signal.
INT t1NetworkProfileV1_LineInterface_R1AnirTimer	1.3.6.1.4.1.529.23.126.2.1.62	INTEGER	read-write	Time in milliseconds of ANIR signal.
INT t1NetworkProfileV1_LineInterface_R1FirstDigitTimer	1.3.6.1.4.1.529.23.126.2.1.60	INTEGER	read-write	The timer between sending KPA and receiving first Digit in R1 signaling in milliseconds.
INT t1NetworkProfileV1_LineInterface_R1Modified	1.3.6.1.4.1.529.23.126.2.1.63	INTEGER	read-write	Use R1 modified signaling. Default is FALSE.
INT t1NetworkProfileV1_LineInterface_R1UseAnir	1.3.6.1.4.1.529.23.126.2.1.59	INTEGER	read-write	TRUE if the line is to use R1 signaling ANIR (CLID), otherwise FALSE.
INT t1NetworkProfileV1_LineInterface_RobbedBitMode	1.3.6.1.4.1.529.23.126.2.1.11	INTEGER	read-write	Wink start, idle start, incoming wink.
INT t1NetworkProfileV1_LineInterface_SendDiscVal	1.3.6.1.4.1.529.23.126.2.1.50	INTEGER	read-write	Number of seconds before sending ISDN disconnect to switch. 0 means disable.
INT t1NetworkProfileV1_LineInterface_SignalingMode	1.3.6.1.4.1.529.23.126.2.1.9	INTEGER	read-write	Inband, ISDN, ISDN_NFAS, PBX or SS7 signaling.
INT t1NetworkProfileV1_LineInterface_Ss7Continuity_IncomingProcedure	1.3.6.1.4.1.529.23.126.2.1.67	INTEGER	read-write	Procedure used for incoming continuity check on this line.
INT t1NetworkProfileV1_LineInterface_Ss7Continuity_OutgoingProcedure	1.3.6.1.4.1.529.23.126.2.1.68	INTEGER	read-write	Procedure used for outgoing continuity check on this line.
INT t1NetworkProfileV1_LineInterface_StatusChangeTrapEnable	1.3.6.1.4.1.529.23.126.2.1.75	INTEGER	read-write	When set to yes, a line status change trap is sent. NOTE: when the line status change results from a higher level line status change, i.e., ds3, then no trap for the ds1 are sent. The default setting is No.
INT t1NetworkProfileV1_LineInterface_SuperFrameSrcLineNumber	1.3.6.1.4.1.529.23.126.2.1.56	INTEGER	read-write	The line from which the the Super-Frame sync pulse is taken. Needed by the 'Dropped&Inserted' line so that it can become synchronized to the source line.
INT t1NetworkProfileV1_LineInterface_SwitchType	1.3.6.1.4.1.529.23.126.2.1.13	INTEGER	read-write	The network switch type, needed for ISDN/NFAS signaling.
INT t1NetworkProfileV1_LineInterface_SwitchVersion	1.3.6.1.4.1.529.23.126.2.1.73	INTEGER	read-write	Switch Version.
INT t1NetworkProfileV1_LineInterface_T1InterDigitTimeout	1.3.6.1.4.1.529.23.126.2.1.58	INTEGER	read-write	Inter-Digit Timeout (in milliseconds) for inband T1 and E1 R2 lines.
INT t1NetworkProfileV1_LineInterface_T302Timer	1.3.6.1.4.1.529.23.126.2.1.32	INTEGER	read-write	Number of milliseconds to wait for additional called number information elements for an incoming call using overlap receiving procedure. Defaults to 10000.
INT t1NetworkProfileV1_LineInterface_Timer1CollectCall	1.3.6.1.4.1.529.23.126.2.1.48	INTEGER	read-write	Adjustable between 0 ~ 2000ms
INT t1NetworkProfileV1_LineInterface_Timer2CollectCall	1.3.6.1.4.1.529.23.126.2.1.49	INTEGER	read-write	Adjustable between 10 ~ 2000ms
INT t1NetworkProfileV1_LineInterface_TOnlineType	1.3.6.1.4.1.529.23.126.2.1.4	INTEGER	read-write	The tonline type of an e1 line.
INT t1NetworkProfileV1_LineInterface_TrailingDigits	1.3.6.1.4.1.529.23.126.2.1.31	INTEGER	read-write	Number of trailing digits expected from the called party number information elements of INFORMATION messages when overlap receiving procedure is used to handle the incoming call. SETUP message may contain some trailing digits in the called party number information element. Defaults to 2.
INT t1NetworkProfileV1_LineInterface_UpTransDelay	1.3.6.1.4.1.529.23.126.2.1.77	INTEGER	read-write	To control the delay in line state transition from down to up when carrier is detected. Each unit of this value is equal to .1 seconds of Delay in DOWN to UP transition.
STR t1NetworkProfileV1_Name	1.3.6.1.4.1.529.23.126.1.1.2	DisplayString	read-only	Name of DS1 line.
INT t1NetworkProfileV1_PhysicalAddress_ItemNumber	1.3.6.1.4.1.529.23.126.1.1.5	INTEGER	read-write	A number that specifies an addressable entity within the context of shelf and slot.
INT t1NetworkProfileV1_PhysicalAddress_Shelf	1.3.6.1.4.1.529.23.126.1.1.3	INTEGER	read-write	The number of the shelf that the addressed physical device resides on.
INT t1NetworkProfileV1_PhysicalAddress_Slot	1.3.6.1.4.1.529.23.126.1.1.4	INTEGER	read-write	The number of the slot that the addressed physical device resides on.
INT t1NetworkProfileV1_PrimaryChannelUsage	1.3.6.1.4.1.529.23.126.1.1.7	INTEGER	read-write	This is the use of the first T1 interface.
INT t1NetworkProfileV1_ProfileNumber	1.3.6.1.4.1.529.23.126.1.1.1	INTEGER	read-write	For potential backwards compatibility. The current design consists of one line profile numbered 0.
INT t1NetworkProfileV1_SecondaryChannelUsage	1.3.6.1.4.1.529.23.126.1.1.8	INTEGER	read-write	The Multiband uses the first T1 interface as the primary interface and treats the secondary interface special. This is the use of the second interface.
INT t1NetworkProfileV1_TertiaryChannelUsage	1.3.6.1.4.1.529.23.126.1.1.9	INTEGER	read-write	This is the use of the 3rd T1 interface.

RFC description

Vendor-private Ascend MIB for T1 network interface management; defines objects for T1 link monitoring, statistics, and configuration on Ascend access devices.

Start monitoring Ascend Communications (Lucent) MAX/Pipeline/TNT WAN access equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ASCEND-MIBT1NET-MIB

What Is ASCEND-MIBT1NET-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description