ASCEND-MIBFILTR-MIB

All MIBs › ASCEND-MIBFILTR-MIB

Category: VPN and Security, Vendor: Ascend/Lucent

Description: Manages packet filter rule sets and access control lists on Ascend WAN access equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ASCEND-MIBFILTR-MIB?

This proprietary Ascend Communications MIB manages packet filter rule sets and access control lists on Ascend WAN access equipment. It exposes configuration data describing filter rule sets and, where available, counters reflecting filter rule matches. Its monitoring value is confirming the software-enforced security/traffic policy is active as intended — an operator checks that the correct filter rules are applied to an interface and reviews match counters to verify traffic is being permitted or blocked as configured, useful for diagnosing why legitimate traffic is being dropped or unwanted traffic is getting through. It is a vendor-proprietary MIB with no direct IETF standard equivalent, specific to Ascend's WAN access filtering implementation. It was deployed on legacy Ascend/Lucent WAN access routers and concentrators enforcing basic packet filtering/ACL policy. Engineers can download the ASCEND-MIBFILTR-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ASCEND-MIBFILTR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

legacy Ascend WAN access router/concentrator

Monitoring Examples

No specific object or table names were included in the sampled instrumentation for this module, so a concrete polling example can't be tied to real OIDs; in general, an operator would check the configured filter rule sets applied to a WAN interface and any available match counters to confirm traffic is being filtered as intended, investigating unexpectedly blocked or permitted traffic as a sign of a misapplied filter rule.

What Can Be Monitored

packet filter rule set configuration
ACL assignment per interface
filter rule match counts

Imported Objects

From ASCEND-MIB

configuration

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT filterProfile_Action_o	1.3.6.1.4.1.529.23.77.1.1.2	INTEGER	read-write
STR filterProfile_FilterName	1.3.6.1.4.1.529.23.77.1.1.1	DisplayString	read-only	The name of this filter. All filters are referenced by name so a name must be assigned to active filters.
STR filterProfile_InputFilters_FilterName	1.3.6.1.4.1.529.23.77.3.1.1	DisplayString	read-only
INT filterProfile_InputFilters_Forward	1.3.6.1.4.1.529.23.77.3.1.4	INTEGER	read-write	When TRUE a packet matching this filter will be forwarded or restart the idle timer. When FALSE a packet matching this filter will be dropped or not restart the idle timer.
INT filterProfile_InputFilters_GenFilter_CompNeq	1.3.6.1.4.1.529.23.77.3.1.9	INTEGER	read-write	Defines type of comparison( Equals(FALSE) or Notequals(TRUE). Default is Equals.
INT filterProfile_InputFilters_GenFilter_Len	1.3.6.1.4.1.529.23.77.3.1.7	INTEGER	read-write	Number of octets to test. Max value is 8 octets.
STR filterProfile_InputFilters_GenFilter_Mask	1.3.6.1.4.1.529.23.77.3.1.10	DisplayString	read-write	A mask to be applied to the data at offset. Only the first len octets will be applied.
INT filterProfile_InputFilters_GenFilter_More	1.3.6.1.4.1.529.23.77.3.1.8	INTEGER	read-write	Include next entry in as part of filter.
INT filterProfile_InputFilters_GenFilter_Offset	1.3.6.1.4.1.529.23.77.3.1.6	INTEGER	read-write	Offset from start of frame of data to test.
STR filterProfile_InputFilters_GenFilter_Value	1.3.6.1.4.1.529.23.77.3.1.11	DisplayString	read-write	The value to compare with the masked data. Only the first len octets will be compared.
INT filterProfile_InputFilters_Index_o	1.3.6.1.4.1.529.23.77.3.1.2	INTEGER	read-only
IP filterProfile_InputFilters_IpFilter_DestAddress	1.3.6.1.4.1.529.23.77.3.1.16	IpAddress	read-write	A value to compare with the masked destination addresses.
IP filterProfile_InputFilters_IpFilter_DestAddressMask	1.3.6.1.4.1.529.23.77.3.1.15	IpAddress	read-write	A mask to apply to a destination address before comparison.
INT filterProfile_InputFilters_IpFilter_DestPort	1.3.6.1.4.1.529.23.77.3.1.20	INTEGER	read-write	A value to compare with the destination port. The comparison is defined by the destTest field.
INT filterProfile_InputFilters_IpFilter_oDstPortCmp	1.3.6.1.4.1.529.23.77.3.1.19	INTEGER	read-write	The type of comparison for the destination port field. May be set to no comparison.
INT filterProfile_InputFilters_IpFilter_oSrcPortCmp	1.3.6.1.4.1.529.23.77.3.1.17	INTEGER	read-write	The type of comparison for the source port field. May be set to no comparison.
INT filterProfile_InputFilters_IpFilter_Protocol	1.3.6.1.4.1.529.23.77.3.1.12	INTEGER	read-write	The protocol number of the protocol to filter for. If set to zero this entry will match any IP protocol.
IP filterProfile_InputFilters_IpFilter_SourceAddress	1.3.6.1.4.1.529.23.77.3.1.14	IpAddress	read-write	A value to compare with the masked source addresses.
IP filterProfile_InputFilters_IpFilter_SourceAddressMask	1.3.6.1.4.1.529.23.77.3.1.13	IpAddress	read-write	A mask to apply to a source address before comparison.
INT filterProfile_InputFilters_IpFilter_SourcePort	1.3.6.1.4.1.529.23.77.3.1.18	INTEGER	read-write	A value to compare with the source port. The comparison is defined by the sourceTest field.
INT filterProfile_InputFilters_IpFilter_TcpEstab	1.3.6.1.4.1.529.23.77.3.1.21	INTEGER	read-write	Indicates whether to look at tcp packets in an established connection.
STR filterProfile_InputFilters_IpxFilter_DestNetAddress	1.3.6.1.4.1.529.23.77.3.1.29	DisplayString	read-write	A value to compare with destination network addresses.
STR filterProfile_InputFilters_IpxFilter_DestNodeAddress	1.3.6.1.4.1.529.23.77.3.1.31	DisplayString	read-write	A value to compare with destination node addresses.
INT filterProfile_InputFilters_IpxFilter_DestSocket	1.3.6.1.4.1.529.23.77.3.1.34	INTEGER	read-write	A value to compare with the destination socket. The comparison is defined by the destTest field.
INT filterProfile_InputFilters_IpxFilter_DstSocketCmp	1.3.6.1.4.1.529.23.77.3.1.35	INTEGER	read-write	The type of comparison for the destination socket field. May be set to no comparison.
STR filterProfile_InputFilters_IpxFilter_SrcNetAddress	1.3.6.1.4.1.529.23.77.3.1.28	DisplayString	read-write	A value to compare with source network addresses.
STR filterProfile_InputFilters_IpxFilter_SrcNodeAddress	1.3.6.1.4.1.529.23.77.3.1.30	DisplayString	read-write	A value to compare with source node addresses.
STR filterProfile_InputFilters_IpxFilter_SrcSocket	1.3.6.1.4.1.529.23.77.3.1.32	DisplayString	read-write	The type of comparison for the source socket field. May be set to no comparison.
INT filterProfile_InputFilters_IpxFilter_SrcSocketCmp	1.3.6.1.4.1.529.23.77.3.1.33	INTEGER	read-write	The type of comparison for the source socket field. May be set to no comparison.
INT filterProfile_InputFilters_oType	1.3.6.1.4.1.529.23.77.3.1.5	INTEGER	read-write	The type of filter contained in this entry. Used to select which of the following fields should be used.
INT filterProfile_InputFilters_RouteFilter_Action	1.3.6.1.4.1.529.23.77.3.1.27	INTEGER	read-write	The type of action taken when match occurs.
INT filterProfile_InputFilters_RouteFilter_AddMetric	1.3.6.1.4.1.529.23.77.3.1.26	INTEGER	read-write	A value to be added to metric of the route, this is valid only when action is add.
IP filterProfile_InputFilters_RouteFilter_RouteAddress	1.3.6.1.4.1.529.23.77.3.1.25	IpAddress	read-write	A value to compare with the masked destination addresses.
IP filterProfile_InputFilters_RouteFilter_RouteMask	1.3.6.1.4.1.529.23.77.3.1.24	IpAddress	read-write	A mask to apply to a destination address before comparison.
IP filterProfile_InputFilters_RouteFilter_SourceAddress	1.3.6.1.4.1.529.23.77.3.1.23	IpAddress	read-write	A value to compare with the masked source addresses.
IP filterProfile_InputFilters_RouteFilter_SourceAddressMask	1.3.6.1.4.1.529.23.77.3.1.22	IpAddress	read-write	A mask to apply to a source address before comparison.
IP filterProfile_InputFilters_TosFilter_DestAddress	1.3.6.1.4.1.529.23.77.3.1.40	IpAddress	read-write	A value to compare with the masked destination addresses.
IP filterProfile_InputFilters_TosFilter_DestAddressMask	1.3.6.1.4.1.529.23.77.3.1.39	IpAddress	read-write	A mask to apply to a destination address before comparison.
INT filterProfile_InputFilters_TosFilter_DestPort	1.3.6.1.4.1.529.23.77.3.1.44	INTEGER	read-write	A value to compare with the destination port. The comparison is defined by the destTest field.
STR filterProfile_InputFilters_TosFilter_Dscp	1.3.6.1.4.1.529.23.77.3.1.48	DisplayString	read-write	DSCP tag to be used in marking of the packets (if marking-type = dscp).
INT filterProfile_InputFilters_TosFilter_MarkingType	1.3.6.1.4.1.529.23.77.3.1.47	INTEGER	read-write	Select type of packet marking.
INT filterProfile_InputFilters_TosFilter_oDstPortCmp	1.3.6.1.4.1.529.23.77.3.1.43	INTEGER	read-write	The type of comparison for the destination port field. May be set to no comparison.
INT filterProfile_InputFilters_TosFilter_oSrcPortCmp	1.3.6.1.4.1.529.23.77.3.1.41	INTEGER	read-write	The type of comparison for the source port field. May be set to no comparison.
INT filterProfile_InputFilters_TosFilter_Precedence	1.3.6.1.4.1.529.23.77.3.1.45	INTEGER	read-write	Tag the precedence bits (priority bits) in the TOS octet of IP datagram header with this value when match occurs.
INT filterProfile_InputFilters_TosFilter_Protocol	1.3.6.1.4.1.529.23.77.3.1.36	INTEGER	read-write	The protocol number of the protocol you like to support type-of-service. If set to zero this entry will match any IP protocol.
IP filterProfile_InputFilters_TosFilter_SourceAddress	1.3.6.1.4.1.529.23.77.3.1.38	IpAddress	read-write	A value to compare with the masked source addresses.
IP filterProfile_InputFilters_TosFilter_SourceAddressMask	1.3.6.1.4.1.529.23.77.3.1.37	IpAddress	read-write	A mask to apply to a source address before comparison.
INT filterProfile_InputFilters_TosFilter_SourcePort	1.3.6.1.4.1.529.23.77.3.1.42	INTEGER	read-write	A value to compare with the source port. The comparison is defined by the sourceTest field.
INT filterProfile_InputFilters_TosFilter_TypeOfService	1.3.6.1.4.1.529.23.77.3.1.46	INTEGER	read-write	Tag the type of service field in the TOS octet of IP datagram header with this value when match occurs.
INT filterProfile_InputFilters_ValidEntry	1.3.6.1.4.1.529.23.77.3.1.3	INTEGER	read-write	When TRUE, this filter entry has been defined and properly initialized. When FALSE, this entry should be skipped when filtering.
STR filterProfile_OutputFilters_FilterName	1.3.6.1.4.1.529.23.77.2.1.1	DisplayString	read-only
INT filterProfile_OutputFilters_Forward	1.3.6.1.4.1.529.23.77.2.1.4	INTEGER	read-write	When TRUE a packet matching this filter will be forwarded or restart the idle timer. When FALSE a packet matching this filter will be dropped or not restart the idle timer.
INT filterProfile_OutputFilters_GenFilter_CompNeq	1.3.6.1.4.1.529.23.77.2.1.9	INTEGER	read-write	Defines type of comparison( Equals(FALSE) or Notequals(TRUE). Default is Equals.
INT filterProfile_OutputFilters_GenFilter_Len	1.3.6.1.4.1.529.23.77.2.1.7	INTEGER	read-write	Number of octets to test. Max value is 8 octets.
STR filterProfile_OutputFilters_GenFilter_Mask	1.3.6.1.4.1.529.23.77.2.1.10	DisplayString	read-write	A mask to be applied to the data at offset. Only the first len octets will be applied.
INT filterProfile_OutputFilters_GenFilter_More	1.3.6.1.4.1.529.23.77.2.1.8	INTEGER	read-write	Include next entry in as part of filter.
INT filterProfile_OutputFilters_GenFilter_Offset	1.3.6.1.4.1.529.23.77.2.1.6	INTEGER	read-write	Offset from start of frame of data to test.
STR filterProfile_OutputFilters_GenFilter_Value	1.3.6.1.4.1.529.23.77.2.1.11	DisplayString	read-write	The value to compare with the masked data. Only the first len octets will be compared.
INT filterProfile_OutputFilters_Index_o	1.3.6.1.4.1.529.23.77.2.1.2	INTEGER	read-only
IP filterProfile_OutputFilters_IpFilter_DestAddress	1.3.6.1.4.1.529.23.77.2.1.16	IpAddress	read-write	A value to compare with the masked destination addresses.
IP filterProfile_OutputFilters_IpFilter_DestAddressMask	1.3.6.1.4.1.529.23.77.2.1.15	IpAddress	read-write	A mask to apply to a destination address before comparison.
INT filterProfile_OutputFilters_IpFilter_DestPort	1.3.6.1.4.1.529.23.77.2.1.20	INTEGER	read-write	A value to compare with the destination port. The comparison is defined by the destTest field.
INT filterProfile_OutputFilters_IpFilter_oDstPortCmp	1.3.6.1.4.1.529.23.77.2.1.19	INTEGER	read-write	The type of comparison for the destination port field. May be set to no comparison.
INT filterProfile_OutputFilters_IpFilter_oSrcPortCmp	1.3.6.1.4.1.529.23.77.2.1.17	INTEGER	read-write	The type of comparison for the source port field. May be set to no comparison.
INT filterProfile_OutputFilters_IpFilter_Protocol	1.3.6.1.4.1.529.23.77.2.1.12	INTEGER	read-write	The protocol number of the protocol to filter for. If set to zero this entry will match any IP protocol.
IP filterProfile_OutputFilters_IpFilter_SourceAddress	1.3.6.1.4.1.529.23.77.2.1.14	IpAddress	read-write	A value to compare with the masked source addresses.
IP filterProfile_OutputFilters_IpFilter_SourceAddressMask	1.3.6.1.4.1.529.23.77.2.1.13	IpAddress	read-write	A mask to apply to a source address before comparison.
INT filterProfile_OutputFilters_IpFilter_SourcePort	1.3.6.1.4.1.529.23.77.2.1.18	INTEGER	read-write	A value to compare with the source port. The comparison is defined by the sourceTest field.
INT filterProfile_OutputFilters_IpFilter_TcpEstab	1.3.6.1.4.1.529.23.77.2.1.21	INTEGER	read-write	Indicates whether to look at tcp packets in an established connection.
STR filterProfile_OutputFilters_IpxFilter_DestNetAddress	1.3.6.1.4.1.529.23.77.2.1.29	DisplayString	read-write	A value to compare with destination network addresses.
STR filterProfile_OutputFilters_IpxFilter_DestNodeAddress	1.3.6.1.4.1.529.23.77.2.1.31	DisplayString	read-write	A value to compare with destination node addresses.
INT filterProfile_OutputFilters_IpxFilter_DestSocket	1.3.6.1.4.1.529.23.77.2.1.34	INTEGER	read-write	A value to compare with the destination socket. The comparison is defined by the destTest field.
INT filterProfile_OutputFilters_IpxFilter_DstSocketCmp	1.3.6.1.4.1.529.23.77.2.1.35	INTEGER	read-write	The type of comparison for the destination socket field. May be set to no comparison.
STR filterProfile_OutputFilters_IpxFilter_SrcNetAddress	1.3.6.1.4.1.529.23.77.2.1.28	DisplayString	read-write	A value to compare with source network addresses.
STR filterProfile_OutputFilters_IpxFilter_SrcNodeAddress	1.3.6.1.4.1.529.23.77.2.1.30	DisplayString	read-write	A value to compare with source node addresses.
STR filterProfile_OutputFilters_IpxFilter_SrcSocket	1.3.6.1.4.1.529.23.77.2.1.32	DisplayString	read-write	The type of comparison for the source socket field. May be set to no comparison.
INT filterProfile_OutputFilters_IpxFilter_SrcSocketCmp	1.3.6.1.4.1.529.23.77.2.1.33	INTEGER	read-write	The type of comparison for the source socket field. May be set to no comparison.
INT filterProfile_OutputFilters_oType	1.3.6.1.4.1.529.23.77.2.1.5	INTEGER	read-write	The type of filter contained in this entry. Used to select which of the following fields should be used.
INT filterProfile_OutputFilters_RouteFilter_Action	1.3.6.1.4.1.529.23.77.2.1.27	INTEGER	read-write	The type of action taken when match occurs.
INT filterProfile_OutputFilters_RouteFilter_AddMetric	1.3.6.1.4.1.529.23.77.2.1.26	INTEGER	read-write	A value to be added to metric of the route, this is valid only when action is add.
IP filterProfile_OutputFilters_RouteFilter_RouteAddress	1.3.6.1.4.1.529.23.77.2.1.25	IpAddress	read-write	A value to compare with the masked destination addresses.
IP filterProfile_OutputFilters_RouteFilter_RouteMask	1.3.6.1.4.1.529.23.77.2.1.24	IpAddress	read-write	A mask to apply to a destination address before comparison.
IP filterProfile_OutputFilters_RouteFilter_SourceAddress	1.3.6.1.4.1.529.23.77.2.1.23	IpAddress	read-write	A value to compare with the masked source addresses.
IP filterProfile_OutputFilters_RouteFilter_SourceAddressMask	1.3.6.1.4.1.529.23.77.2.1.22	IpAddress	read-write	A mask to apply to a source address before comparison.
IP filterProfile_OutputFilters_TosFilter_DestAddress	1.3.6.1.4.1.529.23.77.2.1.40	IpAddress	read-write	A value to compare with the masked destination addresses.
IP filterProfile_OutputFilters_TosFilter_DestAddressMask	1.3.6.1.4.1.529.23.77.2.1.39	IpAddress	read-write	A mask to apply to a destination address before comparison.
INT filterProfile_OutputFilters_TosFilter_DestPort	1.3.6.1.4.1.529.23.77.2.1.44	INTEGER	read-write	A value to compare with the destination port. The comparison is defined by the destTest field.
STR filterProfile_OutputFilters_TosFilter_Dscp	1.3.6.1.4.1.529.23.77.2.1.48	DisplayString	read-write	DSCP tag to be used in marking of the packets (if marking-type = dscp).
INT filterProfile_OutputFilters_TosFilter_MarkingType	1.3.6.1.4.1.529.23.77.2.1.47	INTEGER	read-write	Select type of packet marking.
INT filterProfile_OutputFilters_TosFilter_oDstPortCmp	1.3.6.1.4.1.529.23.77.2.1.43	INTEGER	read-write	The type of comparison for the destination port field. May be set to no comparison.
INT filterProfile_OutputFilters_TosFilter_oSrcPortCmp	1.3.6.1.4.1.529.23.77.2.1.41	INTEGER	read-write	The type of comparison for the source port field. May be set to no comparison.
INT filterProfile_OutputFilters_TosFilter_Precedence	1.3.6.1.4.1.529.23.77.2.1.45	INTEGER	read-write	Tag the precedence bits (priority bits) in the TOS octet of IP datagram header with this value when match occurs.
INT filterProfile_OutputFilters_TosFilter_Protocol	1.3.6.1.4.1.529.23.77.2.1.36	INTEGER	read-write	The protocol number of the protocol you like to support type-of-service. If set to zero this entry will match any IP protocol.
IP filterProfile_OutputFilters_TosFilter_SourceAddress	1.3.6.1.4.1.529.23.77.2.1.38	IpAddress	read-write	A value to compare with the masked source addresses.
IP filterProfile_OutputFilters_TosFilter_SourceAddressMask	1.3.6.1.4.1.529.23.77.2.1.37	IpAddress	read-write	A mask to apply to a source address before comparison.
INT filterProfile_OutputFilters_TosFilter_SourcePort	1.3.6.1.4.1.529.23.77.2.1.42	INTEGER	read-write	A value to compare with the source port. The comparison is defined by the sourceTest field.
INT filterProfile_OutputFilters_TosFilter_TypeOfService	1.3.6.1.4.1.529.23.77.2.1.46	INTEGER	read-write	Tag the type of service field in the TOS octet of IP datagram header with this value when match occurs.
INT filterProfile_OutputFilters_ValidEntry	1.3.6.1.4.1.529.23.77.2.1.3	INTEGER	read-write	When TRUE, this filter entry has been defined and properly initialized. When FALSE, this entry should be skipped when filtering.
mibfilterProfile	1.3.6.1.4.1.529.23.77
mibfilterProfile_InputFiltersEntry	1.3.6.1.4.1.529.23.77.3.1		not-accessible	A mibfilterProfile__input_filters entry containing objects that maps to the parameters of mibfilterProfile__input_filters profile.
mibfilterProfile_InputFiltersTable	1.3.6.1.4.1.529.23.77.3		not-accessible	A list of mibfilterProfile__input_filters profile entries.
mibfilterProfile_OutputFiltersEntry	1.3.6.1.4.1.529.23.77.2.1		not-accessible	A mibfilterProfile__output_filters entry containing objects that maps to the parameters of mibfilterProfile__output_filters profile.
mibfilterProfile_OutputFiltersTable	1.3.6.1.4.1.529.23.77.2		not-accessible	A list of mibfilterProfile__output_filters profile entries.
mibfilterProfileEntry	1.3.6.1.4.1.529.23.77.1.1		not-accessible	A mibfilterProfile entry containing objects that maps to the parameters of mibfilterProfile profile.
mibfilterProfileTable	1.3.6.1.4.1.529.23.77.1		not-accessible	A list of mibfilterProfile profile entries.

RFC description

Manages filter profiles on Ascend communications equipment with named filters and action configurations.

Start monitoring Ascend Communications (Lucent) MAX/Pipeline/TNT WAN access equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ASCEND-MIBFILTR-MIB

What Is ASCEND-MIBFILTR-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description