ARUBAWIRED-RPVST-MIB

All MIBs › ARUBAWIRED-RPVST-MIB

Organization: HPE/Aruba Networking Division

Last Updated: 2020-11-25

Category: VLAN and Bridging, Vendor: Aruba

Description: Monitors Rapid Per-VLAN Spanning Tree protocol state and topology on Aruba CX switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ARUBAWIRED-RPVST-MIB?

ARUBAWIRED-RPVST-MIB is an HPE/Aruba Networking enterprise MIB (under the wndFeatures OID arc) that models Rapid Per-VLAN Spanning Tree (RPVST, a rapid spanning tree instance run independently per VLAN, interoperable with legacy Cisco PVST+) on Aruba CX-family wired switches. It exposes global RPVST behavior scalars such as arubaWiredRpvstPathCostMode (802.1d/802.1t/proprietary cost calculation), arubaWiredRpvstExtendedSystemID, arubaWiredRpvstBpduGuardTimeout, and arubaWiredRpvstMstpInterconnectVlan (the VLAN used to bridge an RPVST domain into an MSTP domain), alongside a per-VLAN arubaWiredRpvstVlanTable carrying arubaWiredRpvstVlanHelloTime/ForwardDelay/MaxAge/Priority, arubaWiredRpvstVlanRoot, arubaWiredRpvstVlanRpvstAdminStatus, and reset-counter controls. Because RPVST determines the active forwarding topology per VLAN, this data is central to detecting topology instability — administrators watch for unexpected root-bridge changes, per-VLAN inconsistency reasons, or repeated counter resets indicating flapping links or misconfigured point-to-point/edge-port settings. It depends on Q-BRIDGE-MIB for VlanIndex typing and IF-MIB for interface indexing, and it is deployed on Aruba (HPE) CX-series wired switches running RPVST in campus or data-center access-layer topologies; network teams can pull the ARUBAWIRED-RPVST-MIB MIB from HPE to build monitoring against this object set.

IPNetwork Monitor allows you to monitor SNMP objects defined in ARUBAWIRED-RPVST-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aruba (HPE) CX-series wired switches

Monitoring Examples

An operator polls arubaWiredRpvstVlanTable for a given VLAN to check arubaWiredRpvstVlanRoot and arubaWiredRpvstVlanRootPathCost, confirming the expected switch holds the root role; an unexpected change in arubaWiredRpvstVlanRoot combined with an active port/VLAN inconsistency reason on a trunk port would indicate a PVID mismatch or a rogue bridge contending for root on that VLAN.

What Can Be Monitored

per-VLAN root bridge/root path cost
per-VLAN hello/forward-delay/max-age timers
RPVST admin status per VLAN
BPDU guard timeout state
port/VLAN inconsistency reasons
RPVST-to-MSTP interconnect VLAN configuration

Imported Objects

From ARUBAWIRED-NETWORKING-OID

wndFeatures

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From Q-BRIDGE-MIB

VlanIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using arubaWiredRpvstVlanRootChangeCounter OID:

Select an Aruba (HPE) ArubaOS-CX wired switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type arubaWiredRpvstVlanRootChangeCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of times the root has changed for this VLAN. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
arubaWiredRpvstMIB	1.3.6.1.4.1.47196.4.1.1.3.5			This MIB module for Rapid Per VLAN Spanning Tree(RPVST).
arubaWiredRpvstNotifications	1.3.6.1.4.1.47196.4.1.1.3.5.0
NTF arubaWiredRpvstErrantBpduReceived	1.3.6.1.4.1.47196.4.1.1.3.5.0.1			This Trap is generated when an unexpected (errant) BPDU has been received on a port.
NTF arubaWiredRpvstNewRoot	1.3.6.1.4.1.47196.4.1.1.3.5.0.2			Trap generated when sending agent has become the new root of spanning Tree for the specified VLAN; the notification is sent by a bridge soon after its election as the new root.
NTF arubaWiredRpvstRootGuardInconsistency	1.3.6.1.4.1.47196.4.1.1.3.5.0.3			Trap generated when a Root Guard feature enabled port receives superior BPDUs on its interface for a given instance.
NTF arubaWiredRpvstLoopGuardInconsistency	1.3.6.1.4.1.47196.4.1.1.3.5.0.4			Trap generated when a Loop Guard feature enabled port receives superior BPDUs on its interface for a given instance.
NTF arubaWiredRpvstTopologyChange	1.3.6.1.4.1.47196.4.1.1.3.5.0.5			Trap is generated when a Topology Change is detected in the specified VLAN.
arubaWiredRpvstObjects	1.3.6.1.4.1.47196.4.1.1.3.5.1
arubaWiredRpvstGeneralGroup	1.3.6.1.4.1.47196.4.1.1.3.5.1.1
T/F arubaWiredRpvstResetCounters	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.1	TruthValue	read-write	Setting this object to true(1) will reset all the RPVST counters. Setting this to false(2) is no operation.
T/F arubaWiredRpvstExtendedSystemID	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.2	TruthValue	read-write	Creates a unique bridge identifier for each VLAN by adding the VLAN ID (vid) value to the priority field of the bridge identifier in every RPVST BPDU. Indicates whether Extended System ID feature is enabled or not.
T/F arubaWiredRpvstIgnorePVIDInconsistency	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.3	TruthValue	read-write	Setting this object to True(1) will enable RPVST to run on mismatched PVID links.Once set it will apply to all RPVST instances
INT arubaWiredRpvstPathCostMode	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.4	INTEGER	read-write	arubaWiredRpvstPathCostMode controls which pathcost mode to use. A device can function in one of the 3 modes defined below. pathCost8021d - The device calculates the default path cost for ports based on IEEE 802.1d. pathCost8021t - The device calculates the default path cost for ports based on IEEE 802.1t. proprietary -The device calculates the default path cost for ports based on the proprietary standard. Link Speed Vs Pathcost Table ---------------------------------------------------------- \|Link speed\| Pathcost in \| Pathcost in \| Pathcost in \| \| \| IEEE802.1d \| IEEE 802.1t \| private standard\| ---------------------------------------------------------- \| 10 Mbps \| 100 \| 2,000,000 \| 100 \| ---------------------------------------------------------- \| 100 Mbps \| 10 \| 200,000 \| 19 \| ---------------------------------------------------------- \| 1000 Mbps\| 4 \| 20,000 \| 4 \| ---------------------------------------------------------- \| 10 Gbps \| 1 \| 2,000 \| 2 \| ----------------------------------------------------------
I32 arubaWiredRpvstBpduGuardTimeout	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.5	Integer32	read-write	Time in seconds until when a port configured for BPDU-guard will be disabled, upon receiving an STP BPDU. If BpduGuardtimeout is not set, port will be in the disabled state forever.
I32 arubaWiredRpvstMstpInterconnectVlan	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.6	Integer32	read-write	VLAN used to interconnect an RPVST domain to an MSTP domain. This is only applicable if spanning tree is enabled on this device and the mode is set to RPVST.
I32 arubaWiredRpvstCurrentVportCount	1.3.6.1.4.1.47196.4.1.1.3.5.1.1.7	Integer32	read-write	Specifies the current number of RPVST VPORTs configured in the system.
arubaWiredRpvstVlanTable	1.3.6.1.4.1.47196.4.1.1.3.5.1.2		not-accessible	Information describing the RPVST configuration and statistics of the VLANs.
arubaWiredRpvstVlanEntry	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1		not-accessible	Information describing the RPVST configuration and statistics of each of the VLANs.
VLA arubaWiredRpvstVlanId	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.1	VlanIndex	not-accessible	A VLAN ID to uniquely identify the entries.
I32 arubaWiredRpvstVlanHelloTime	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.2	Integer32	read-write	The amount of time between the transmission of configuration BPDUs by this node on any port in this VLAN when it is root of the spanning tree, or trying to become so for this VLAN.
I32 arubaWiredRpvstVlanForwardDelay	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.3	Integer32	read-write	The amount of time between transitioning from listening to learning and learning to forwarding by this node on any port when it is acting as a root for this VLAN.
I32 arubaWiredRpvstVlanMaxAge	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.4	Integer32	read-write	The maximum age of RPVST information learned from the network on any port before it is discarded.
I32 arubaWiredRpvstVlanPriority	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.5	Integer32	read-write	The value of the write-able portion of the Bridge ID (i.e., the first two octets of the (8 octet long) Bridge ID). The other (last) 6 octets of the Bridge ID are given by the value dot1dBridgeBaseAddress.
INT arubaWiredRpvstVlanRoot	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.6	INTEGER	read-write	To explicitly configure this switch to be primary/secondary root for this VLAN.
INT arubaWiredRpvstVlanRpvstAdminStatus	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.7	INTEGER	read-write	To enable/disable RPVST on the VLAN.
T/F arubaWiredRpvstVlanResetCounters	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.8	TruthValue	read-write	Setting this object to true(1) will reset the RPVST counters for this VLAN.
I32 arubaWiredRpvstVlanOperHelloTime	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.9	Integer32	read-only	The amount of time between the transmission of BPDUs by this node on any port in this VLAN when it is root of the spanning tree, or trying to become so for this VLAN. This is the actual value that this bridge is using.
I32 arubaWiredRpvstVlanRootPriority	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.10	Integer32	read-only	The priority of root bridge in this VLAN.
NUM arubaWiredRpvstVlanRootPort	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.11	InterfaceIndex	read-only	The root port for this VLAN.
I32 arubaWiredRpvstVlanRootPathCost	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.12	Integer32	read-only	The path cost to the Root from this bridge in this VLAN.
MAC arubaWiredRpvstVlanRootMacAddress	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.13	MacAddress	read-only	MAC address of the Root in this VLAN.
C32 arubaWiredRpvstVlanRootChangeCounterEx	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.14	Counter32	read-only	The number of times the root has changed for this VLAN.
TIK arubaWiredRpvstVlanTimeSinceLastTopoChange	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.15	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity for this VLAN.
C32 arubaWiredRpvstVlanTopoChangeCount	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.16	Counter32	read-only	The total number of topology changes detected by this bridge in this VLAN since the management entity was last reset or initialized.
T/F arubaWiredRpvstVlanSendTopoChangeCtrl	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.17	TruthValue	read-write	Setting this object to true(1) will enable sending of SNMP notifications for all topology change events on this VLAN.
T/F arubaWiredRpvstVlanLogPortStateTransitions	1.3.6.1.4.1.47196.4.1.1.3.5.1.2.1.18	TruthValue	read-write	Setting this object to true(1) will enable event logging of PVST port state transitions for this VLAN.
arubaWiredRpvstPortTable	1.3.6.1.4.1.47196.4.1.1.3.5.1.3		not-accessible	Information describing the RPVST specific configuration and statistics of the ports.
arubaWiredRpvstPortEntry	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1		not-accessible	Information describing the RPVST specific configuration and statistics of the ports.
NUM arubaWiredRpvstPortIndex	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.1	InterfaceIndex	not-accessible	The port ifIndex
T/F arubaWiredRpvstPortAdminEdge	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.2	TruthValue	read-write	The administrative value of the Edge Port parameter. A value of true(1) indicates that this port should be assumed as an edge-port, and a value of false(2) indicates that this port should be assumed as a non-edge-port. Note that even when this object's value is true(1), the arubaWiredRpvstOperEdgePort can be false(2) if a BPDU has been received.
NUM arubaWiredRpvstPortAdminPointToPoint	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.3	PointToPoint	read-write	Refer the PointToPoint textual-convention.
T/F arubaWiredRpvstPortAutoEdge	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.4	TruthValue	read-write	It is used by the Bridge detection state machine for the automatic identification of edge ports.
T/F arubaWiredRpvstPortBpduFiltering	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.5	TruthValue	read-write	This value indicates whether or not BPDUs need to be filtered on this port and BPDU filter option forces a port to always stay in the forwarding state and be excluded from standard STP operation. If the value is true(1) the received BPDUs will be dropped and no BPDUs will be transmitted on the port. If the value is false (2) the BPDUs will be processed as usual.
T/F arubaWiredRpvstPortRestrictedTcn	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.6	TruthValue	read-write	This value indicates whether or not to propagate topology changes to other ports. true(1) causes the port not to propagate topology changes to other ports.
T/F arubaWiredRpvstPortRootGuard	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.7	TruthValue	read-write	Setting this object to true(1) forces port to not to be selected as root port even if this port has the least path cost to the root.
T/F arubaWiredRpvstPortLoopGuard	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.8	TruthValue	read-write	Setting this object to true(1) causes the non-designated port to go into the STP loop inconsistent state instead of the forwarding state. In the loop-inconsistent state, the port prevents data traffic through the link, therefore avoiding the loop creation. When BPDUs again are received on the inconsistent port, it resumes normal STP operation automatically.
T/F arubaWiredRpvstPortBpduProtection	1.3.6.1.4.1.47196.4.1.1.3.5.1.3.1.9	TruthValue	read-write	Setting this true (1) indicates that no BPDUs are expected to be received on this port. At the reception of BPDUs the BPDU protection mechanism will disable this port and port will transition into BPDU Error state.
arubaWiredRpvstPortVlanTable	1.3.6.1.4.1.47196.4.1.1.3.5.1.4		not-accessible	Information describing the RPVST configuration and statistics of the ports in the given VLAN.
arubaWiredRpvstPortVlanEntry	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1		not-accessible	Information describing the RPVST configuration and statistics of the ports in the given VLAN.
VLA arubaWiredRpvstPortVlanId	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.1	VlanIndex	not-accessible	A VLAN ID to uniquely identify the entries.
NUM arubaWiredRpvstPortVlanIndex	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.2	InterfaceIndex	not-accessible	The port ifIndex
I32 arubaWiredRpvstPortVlanPathCost	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.3	Integer32	read-write	The contribution of this port to the path cost of paths towards the root which include this port. auto(0)
I32 arubaWiredRpvstPortVlanPriority	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.4	Integer32	read-write	The value of the port priority field that is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
T/F arubaWiredRpvstPortVlanResetCounters	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.5	TruthValue	read-write	Setting this object to true(1) will reset the RPVST counters for this port-vlan pair. Get on this object will always return false(2)
INT arubaWiredRpvstPortVlanRole	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.6	INTEGER	read-only	Role played by the port in a given VLAN.
INT arubaWiredRpvstPortVlanState	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.7	INTEGER	read-only	The port's current state. This state controls what action a port takes on reception of a frame.
MAC arubaWiredRpvstPortVlanDesigBridge	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.8	MacAddress	read-only	The Bridge Identifier of the bridge that this port considers to be the Designated Bridge for this port's segment.
T/F arubaWiredRpvstPortVlanOperPointToPoint	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.9	TruthValue	read-only	true : This value indicates that the MAC is connected to a point-to-point LAN segment; i.e., there is at most one other system attached to the LAN segment. false: This value indicates that the MAC is connected to a non-point-to-point LAN segment; i.e., there can be more than one other system attached to the LAN segment.
T/F arubaWiredRpvstPortVlanOperEdge	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.10	TruthValue	read-only	The operational status of the edge port parameter. A value of true(1) indicates that this port should be assumed as an edge-port, and a value of false(2) indicates that this port should be assumed as a non-edge-port.
INT arubaWiredRpvstPortVlanInconsistencyReason	1.3.6.1.4.1.47196.4.1.1.3.5.1.4.1.11	INTEGER	read-only	The reason for which port is blocked by spanning tree protection function.
arubaWiredRpvstNotificationTable	1.3.6.1.4.1.47196.4.1.1.3.5.1.5		not-accessible	Information describing the Rpvst configuration and statistics of the Ports and Vlans.
arubaWiredRpvstNotificationEntry	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1		not-accessible	Information describing the Rpvst events for trap generation.
STR arubaWiredRpvstPortName	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.1	DisplayString	accessible-for-notify	Port name
I32 arubaWiredRpvstVlanIndex	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.2	Integer32	accessible-for-notify	VLAN ID
I32 arubaWiredRpvstPortVlanErrantBpduRxCount	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.3	Integer32	accessible-for-notify	The number of BPDUs received on a BPDU-filtering or BPDU-protected enabled port.
MAC arubaWiredRpvstErrantBpduSrcMac	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.4	MacAddress	accessible-for-notify	The source MAC address of the port sending Errant BPDU.
STR arubaWiredRpvstSuperiorBpduSrcPort	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.5	DisplayString	accessible-for-notify	The name of the port sending superior BPDU
MAC arubaWiredRpvstSuperiorBpduSrcMac	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.6	MacAddress	accessible-for-notify	The MacAddress of the port sending superior BPDU
INT arubaWiredRpvstErrantBpduDetector	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.7	INTEGER	accessible-for-notify	The identifier of the feature generating Errant BPDU trap.
STR arubaWiredRpvstDesignatedPort	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.8	DisplayString	accessible-for-notify	Designated Port of the Bridge.
STR arubaWiredRpvstOldPortRole	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.9	DisplayString	accessible-for-notify	Old Port state
STR arubaWiredRpvstNewPortRole	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.10	DisplayString	accessible-for-notify	new port state
DAT arubaWiredRpvstTopoChangeTime	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.11	DateAndTime	accessible-for-notify	Topology change time
STR arubaWiredRpvstPreviousRootBridgeID	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.12	DisplayString	accessible-for-notify	Bridge ID of the previous Root. Bridge Id consists of priority and MAC address.
STR arubaWiredRpvstNewRootBridgeID	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.13	DisplayString	accessible-for-notify	Bridge ID of the new Root. Bridge Id consists of priority and MAC address.
DAT arubaWiredRpvstRootBridgeChangeTimeStamp	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.14	DateAndTime	accessible-for-notify	Time when the root changed
I32 arubaWiredRpvstId	1.3.6.1.4.1.47196.4.1.1.3.5.1.5.1.15	Integer32	not-accessible	VLAN ID
arubaWiredRpvstConformance	1.3.6.1.4.1.47196.4.1.1.3.5.2
arubaWiredRpvstGroups	1.3.6.1.4.1.47196.4.1.1.3.5.2.1
arubaWiredRpvstGroup	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.1			These objects are used for managing/monitoring RPVST global parameters.
arubaWiredRpvstVlanGroup	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.2			These objects are used for managing/monitoring RPVST VLAN parameters.
arubaWiredRpvstPortVlanGroup	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.3			These objects are used for managing/monitoring RPVST port parameters for the VLANs.
arubaWiredRpvstPortGroup	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.4			These objects are used for managing/monitoring RPVST port parameters
arubaWiredRpvstPvst1	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.5			Group of object added part of pvst1.
arubaWiredRpvstNotificationObjectGrp	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.6			Group of objects required for notifications.
arubaWiredRpvstNotificationGroup	1.3.6.1.4.1.47196.4.1.1.3.5.2.1.7			Group of notifications.
arubaWiredRpvstCompliances	1.3.6.1.4.1.47196.4.1.1.3.5.2.2
arubaWiredRpvstCompliance1	1.3.6.1.4.1.47196.4.1.1.3.5.2.2.1			The compliance statement
arubaWiredRpvstCompliance2	1.3.6.1.4.1.47196.4.1.1.3.5.2.2.2			The compliance statement
arubaWiredRpvstNotificationCompliance	1.3.6.1.4.1.47196.4.1.1.3.5.2.2.3			The compliance statement for Rpvst extension notifications.

RFC description

Implements Rapid Per VLAN Spanning Tree (RPVST) protocol for VLAN-specific spanning tree management on HPE/Aruba switches.

Start monitoring Aruba (HPE) ArubaOS-CX wired switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ARUBAWIRED-RPVST-MIB