ARTEM-COMPOINT-WLAN-MIB

All MIBs › ARTEM-COMPOINT-WLAN-MIB

Organization: Funkwerk Enterprise Communications.

Last Updated: 2005-04-21

Category: Wireless and WLAN

Description: artem ComPoint 802.11 WLAN radio, SSID, and association statistics management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ARTEM-COMPOINT-WLAN-MIB?

ARTEM-COMPOINT-WLAN-MIB is a vendor-specific MIB from Funkwerk Enterprise Communications for the artem ComPoint family of 802.11 wireless access points. It supplies additional attributes not covered by standard wireless MIBs, covering WLAN-specific functionality such as radio configuration, SSID settings, and client association statistics. Its monitoring relevance is in wireless service health: it would let an administrator track radio operational state, per-SSID client counts, and association/disassociation activity to spot coverage problems, overloaded radios, or clients failing to connect. No sample objects were present in the source excerpt, so specific table or object names cannot be confirmed here. It is used alongside standard IEEE802dot11-MIB objects in enterprise deployments of artem/Funkwerk access points, with an ARTEM-COMPOINT-WLAN-MIB download typically needed to load its object definitions into a MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ARTEM-COMPOINT-WLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

artem ComPoint 802.11 WLAN access point

Monitoring Examples

The module description indicates additional WLAN functionality attributes for artem ComPoint access points, but no sample_objects were supplied in the source data, so no specific object or table names can be cited here. A realistic scenario would involve polling per-radio and per-SSID statistics to detect an unusually low or zero associated-client count, suggesting a radio or SSID outage. Without confirmed object names, a precise monitoring walkthrough cannot be responsibly constructed from this input.

What Can Be Monitored

radio operational status
SSID configuration
client association statistics
association/disassociation events

Imported Objects

From RFC1213-MIB

ifIndex

From SNMPv2-CONF

NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using artemLinkTestFramesTransmitted OID:

Select a Funkwerk (artem) ComPoint 802.11 WLAN access point (legacy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type artemLinkTestFramesTransmitted into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. This attribute shows the number of link test frames transmitted. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
artem	1.3.6.1.4.1.4280			Funkwerk Enterprise Communications MIB file that provides additional attributes not covered by standard MIBs for WLAN functionality in artem products.
artemAP	1.3.6.1.4.1.4280.5.2
artemAPGroup	1.3.6.1.4.1.4280.5.2.10			Extended AP parameters not covered in standard 802.11 MIB.
INT artemAPIfIndex	1.3.6.1.4.1.4280.5.2.1.1.3	INTEGER	read-only	ifIndex that is associated to the combination of artemRadioIndex and artemAPServiceSetIndex.
artemAPNotification	1.3.6.1.4.1.4280.5.2.9
T/F artemAPServiceSetAdminStatus	1.3.6.1.4.1.4280.5.2.1.1.4	TruthValue	read-create	This attribute defines if the associated AP service is currently active.
INT artemAPServiceSetIndex	1.3.6.1.4.1.4280.5.2.1.1.1	INTEGER	not-accessible	This is the unique index number for a service set of the given radio.
artemAPServiceSetsEntry	1.3.6.1.4.1.4280.5.2.1.1		not-accessible	An entry in artemAPServiceSetsTable.
ROW artemAPServiceSetsRowStatus	1.3.6.1.4.1.4280.5.2.1.1.2	RowStatus	read-create	Auxiliary variable for creation of new object instances and/or the deletion of existing object instances.
artemAPServiceSetsTable	1.3.6.1.4.1.4280.5.2.1		not-accessible	Attributes for artem AP service sets.
artemBridge	1.3.6.1.4.1.4280.5.1
artemBridgeAutoConfigEntry	1.3.6.1.4.1.4280.5.1.5.1		not-accessible	An entry in artemBridgeAutoConfigTable.
artemBridgeAutoConfigTable	1.3.6.1.4.1.4280.5.1.5		not-accessible	Attributes for artem bridge link auto-configuration.
INT artemBridgeConfigScanTimeout	1.3.6.1.4.1.4280.5.1.1	INTEGER	read-write	This attribute defines the maximum time a bridge auto-configuration scan may take. After this timeout has expired, any auto-configuration scan will be aborted, regardless of current state.
INT artemBridgeConfigSetupTimeout	1.3.6.1.4.1.4280.5.1.2	INTEGER	read-write	This attribute defines the maximum time a bridge auto-configuration setup may take. After this timeout has expired, any auto-configuration setup will be aborted, regardless of current state. In this case, artemBridgePeerConfigSetupResult will be set to 'timeout'.
artemBridgeGroup	1.3.6.1.4.1.4280.5.1.9			artem bridge-specific attributes.
T/F artemBridgeLinkAdminStatus	1.3.6.1.4.1.4280.5.1.3.1.4	TruthValue	read-create	This attribute defines if the associated bridge link is currently active.
OCT artemBridgeLinkAliasName	1.3.6.1.4.1.4280.5.1.3.1.5	OCTET STRING	read-create	This attribute can be used to set a textual alias name for this bridge link. Default is 'wl?_br?', where first '?' is radio number and second '?' is link number on this radio.
NTF artemBridgeLinkConfigScan	1.3.6.1.4.1.4280.5.1.8.2			This notification is thrown whenever the bridge link auto-configuration scanning state changes.
INT artemBridgeLinkConfigScanState	1.3.6.1.4.1.4280.5.1.5.1.2	INTEGER	read-write	This attribute defines the current auto-configuration state. idle(0) - In this state, writing any value starts an auto-configuration scan for bridge link peers. State will change to scanning(1) while the scan is in progress. When the scan is finished, the results are available in the artemBidgePeersTable. scanning(1) - An auto-configuration scan for bridge link peers is currently in progress. When scanning has finished, the state will automatically change to idle(0). busy(2) - An auto-configuration setup is currently in progress on this radio module. Writing this attribute in any state other than idle(0) will return an error.
INT artemBridgeLinkCurrentSpeed	1.3.6.1.4.1.4280.5.1.3.1.6	INTEGER	read-only	This attribute returns the current transmission speed for this link, or 0 if no connection can be established.
INT artemBridgeLinkIfIndex	1.3.6.1.4.1.4280.5.1.3.1.3	INTEGER	read-only	ifIndex that is associated to the combination of artemRadioIndex and artemBridgeLinkIndex.
INT artemBridgeLinkIndex	1.3.6.1.4.1.4280.5.1.3.1.1	INTEGER	not-accessible	This is the unique index number for a bridge link of the given radio.
NTF artemBridgeLinkLock	1.3.6.1.4.1.4280.5.1.8.4			This notification is triggered whenever the lock state of the bridge link changes.
T/F artemBridgeLinkLockState	1.3.6.1.4.1.4280.5.1.5.1.1	TruthValue	read-write	This attribute defines if the bridge is locked. Lock state is common for all bridge links using the same radio. If the bridge is locked, it cannot be discovered by auto-configuration scan, and remote changing of any parameters is blocked.
artemBridgeLinkNotificationGroup	1.3.6.1.4.1.4280.5.1.13			artem notifications for bridge links
NTF artemBridgeLinkOperState	1.3.6.1.4.1.4280.5.1.8.1			This notification is triggered whenever the connection state of the bridge link changes, i.e. link connection is lost, or link connection is restored.
T/F artemBridgeLinkOperStatus	1.3.6.1.4.1.4280.5.1.3.1.8	TruthValue	read-only	This attribute shows if the bridge link connection is currently operative.
MAC artemBridgeLinkPartnerRadioMacAddress	1.3.6.1.4.1.4280.5.1.3.1.7	MacAddress	read-create	This attribute contains the MAC address of the remote radio module. It can be set directly, or via the auto-configuration mechanism.
ROW artemBridgeLinkRowStatus	1.3.6.1.4.1.4280.5.1.3.1.2	RowStatus	read-create	Auxiliary variable for creation of new object instances and/or the deletion of existing object instances.
artemBridgeLinksEntry	1.3.6.1.4.1.4280.5.1.3.1		not-accessible	An entry in artemBridgeLinksTable.
artemBridgeLinksTable	1.3.6.1.4.1.4280.5.1.3		not-accessible	Attributes for artem bridge links.
artemBridgeLinkTestGroup	1.3.6.1.4.1.4280.5.1.12			Attributes for bridge link test.
artemBridgeNotification	1.3.6.1.4.1.4280.5.1.8
MAC artemBridgePeerCompointMacAddress	1.3.6.1.4.1.4280.5.1.6.1.7	MacAddress	read-only	This attribute displays the MAC address of the peer ComPoint. This is not the WLAN radio's MAC address, but rather the MAC address of the first ethernet port.
OCT artemBridgePeerCompointName	1.3.6.1.4.1.4280.5.1.6.1.3	OCTET STRING	read-only	This attribute displays the given node name of the peer ComPoint.
NTF artemBridgePeerConfigSetup	1.3.6.1.4.1.4280.5.1.8.3			This notification is thrown whenever the bridge link auto-configuration setup state changes.
INT artemBridgePeerConfigSetupResult	1.3.6.1.4.1.4280.5.1.6.1.10	INTEGER	read-only	This attribute holds the result after a bridge link auto-config setup. It is reset whenever a new auto-config setup is triggered.
INT artemBridgePeerConfigSetupState	1.3.6.1.4.1.4280.5.1.6.1.9	INTEGER	read-write	This attribute defines the current auto-configuration setup state of the bridge link. idle(0) - No auto-configuration is currently in progress. In this state, writing to this attribute starts auto-configuration of a bridge link to the partner defined by the table row. The state automatically changes to setup(1) for this peer, and to busy(3) for all other peers. setup(1) - Auto-configuration of this bridge link to connect to this peer is currently in progress. As soon as auto-config setup is finished, the state changes back to idle(0). You can check whether auto-config setup succeeded by reading artemBridgePeerConfigSetupResult. busy(2) - Either the bridge link is currently scanning for peers, or auto-configuration setup with another peer is currently in progress for this bridge link. Writing this attribute in any state other than idle(0) returns an error.
INT artemBridgePeerIndex	1.3.6.1.4.1.4280.5.1.6.1.1	INTEGER	not-accessible	The auxiliary variable used to identify instances of the columnar objects in the artemBridgePeersTable.
T/F artemBridgePeerLinkAdminStatus	1.3.6.1.4.1.4280.5.1.6.1.5	TruthValue	read-only	This attribute shows is the peer's bridge link is currently enabled.
OCT artemBridgePeerLinkAliasName	1.3.6.1.4.1.4280.5.1.6.1.2	OCTET STRING	read-only	This attribute shows the user-defined alias name for the peer's bridge link.
T/F artemBridgePeerLockState	1.3.6.1.4.1.4280.5.1.6.1.6	TruthValue	read-only	This attribute defines if the peer's bridge is locked. Lock state is common for all bridge links using the same radio. If the bridge is locked, it cannot be discovered by auto-configuration scan, and changing of any parameters is blocked.
MAC artemBridgePeerRadioMacAddress	1.3.6.1.4.1.4280.5.1.6.1.8	MacAddress	read-only	This attribute displays the peer's WLAN radio's MAC address.
ART artemBridgePeerRSSI	1.3.6.1.4.1.4280.5.1.6.1.4	ArtemRSSI	read-only	This attribute shows the receive signal strength for the signal received from the peer in dBm.
artemBridgePeersEntry	1.3.6.1.4.1.4280.5.1.6.1		not-accessible	An entry in artemBridgePeersTable.
artemBridgePeersGroup	1.3.6.1.4.1.4280.5.1.11			Attributes of the results of bridge link auto-configuration scans.
artemBridgePeersTable	1.3.6.1.4.1.4280.5.1.6		not-accessible	This table contains the results of bridge link auto-configuration scans. Each line represents a possible link partner.
INT artemBridgePrivacyAutoKey	1.3.6.1.4.1.4280.5.1.4.1.2	INTEGER	read-write	Writing this attribute triggers automatic bridge privacy setup. Depending on artemBridgePrivacyMode, a pseudo-random WEP key or passphrase is generated, and privacy is activated. If non-empty keys have previously been set, writing this attribute returns an error.
artemBridgePrivacyEntry	1.3.6.1.4.1.4280.5.1.4.1		not-accessible	An entry in artemBridgePrivacyTable.
artemBridgePrivacyGroup	1.3.6.1.4.1.4280.5.1.10			artem bridge-specific privacy attributes.
INT artemBridgePrivacyMode	1.3.6.1.4.1.4280.5.1.4.1.1	INTEGER	read-write	This attribute selects privacy mode to use for all bridge links on this radio. Privacy is immediately enabled anything different from 'none' is selected and an appropriate key has been set.
artemBridgePrivacyTable	1.3.6.1.4.1.4280.5.1.4		not-accessible	Table of privacy settings, with special privacy modes for bridge links.
artemInterfaceRadioEntry	1.3.6.1.4.1.4280.5.4.1		not-accessible	An entry in artemInterfaceRadioTable.
artemInterfaceRadioTable	1.3.6.1.4.1.4280.5.4		not-accessible	Table of connection between interfaces (ifIndex) and radio indices (artemWLANRadioIndex).
artemLinkTestEntry	1.3.6.1.4.1.4280.5.1.7.1		not-accessible	An entry in artemLinkTestEntry.
C32 artemLinkTestFramesLost	1.3.6.1.4.1.4280.5.1.7.1.9	Counter32	read-only	This attribute shows the number of link test frames for which no reply has been received and therefore are considered lost.
C32 artemLinkTestFramesReceived	1.3.6.1.4.1.4280.5.1.7.1.8	Counter32	read-only	This attribute shows the number of link test frames successfully received.
C32 artemLinkTestFramesTransmittedEx	1.3.6.1.4.1.4280.5.1.7.1.7	Counter32	read-only	This attribute shows the number of link test frames transmitted.
ART artemLinkTestNoiseLocal	1.3.6.1.4.1.4280.5.1.7.1.3	ArtemRSSI	read-only	This attribute shows the measured noise level in dBm.
ART artemLinkTestNoiseRemote	1.3.6.1.4.1.4280.5.1.7.1.4	ArtemRSSI	read-only	This attribute shows the noise level in dBm, as measured by remote bridge link partner.
C32 artemLinkTestRxFrames1	1.3.6.1.4.1.4280.5.1.7.1.21	Counter32	read-only	This attribute shows the number of link test frames that were received at 1 Mbps.
C32 artemLinkTestRxFrames11	1.3.6.1.4.1.4280.5.1.7.1.16	Counter32	read-only	This attribute shows the number of link test frames that were received at 11 Mbps.
C32 artemLinkTestRxFrames12	1.3.6.1.4.1.4280.5.1.7.1.15	Counter32	read-only	This attribute shows the number of link test frames that were received at 12 Mbps.
C32 artemLinkTestRxFrames18	1.3.6.1.4.1.4280.5.1.7.1.14	Counter32	read-only	This attribute shows the number of link test frames that were received at 18 Mbps.
C32 artemLinkTestRxFrames2	1.3.6.1.4.1.4280.5.1.7.1.20	Counter32	read-only	This attribute shows the number of link test frames that were received at 2 Mbps.
C32 artemLinkTestRxFrames24	1.3.6.1.4.1.4280.5.1.7.1.13	Counter32	read-only	This attribute shows the number of link test frames that were received at 24 Mbps.
C32 artemLinkTestRxFrames36	1.3.6.1.4.1.4280.5.1.7.1.12	Counter32	read-only	This attribute shows the number of link test frames that were received at 36 Mbps.
C32 artemLinkTestRxFrames48	1.3.6.1.4.1.4280.5.1.7.1.11	Counter32	read-only	This attribute shows the number of link test frames that were received at 48 Mbps.
C32 artemLinkTestRxFrames5	1.3.6.1.4.1.4280.5.1.7.1.19	Counter32	read-only	This attribute shows the number of link test frames that were received at 5.5 Mbps.
C32 artemLinkTestRxFrames54	1.3.6.1.4.1.4280.5.1.7.1.10	Counter32	read-only	This attribute shows the number of link test frames that were received at 54 Mbps.
C32 artemLinkTestRxFrames6	1.3.6.1.4.1.4280.5.1.7.1.18	Counter32	read-only	This attribute shows the number of link test frames that were received at 6 Mbps.
C32 artemLinkTestRxFrames9	1.3.6.1.4.1.4280.5.1.7.1.17	Counter32	read-only	This attribute shows the number of link test frames that were received at 9 Mbps.
ART artemLinkTestSignalLocal	1.3.6.1.4.1.4280.5.1.7.1.1	ArtemRSSI	read-only	This attribute shows the received signal strength in dBm.
ART artemLinkTestSignalRemote	1.3.6.1.4.1.4280.5.1.7.1.2	ArtemRSSI	read-only	This attribute shows the received signal in dBm, as measured by remote bridge link partner. Reading this attribute triggers transmission of a new link request frame.
INT artemLinkTestSNRLocal	1.3.6.1.4.1.4280.5.1.7.1.5	INTEGER	read-only	This attribute shows the calculated Signal to Noise ratio in dB.
INT artemLinkTestSNRRemote	1.3.6.1.4.1.4280.5.1.7.1.6	INTEGER	read-only	This attribute shows the calculated Signal to Noise ratio in dB, as measured by remote bridge link partner.
artemLinkTestTable	1.3.6.1.4.1.4280.5.1.7		not-accessible	This table contains the link test results for every bridge link. Reading the artemLinkTestSignalRemote attribute triggers transmission of a new link request frame.
INT artemRadioAckWindow	1.3.6.1.4.1.4280.5.3.1.7	INTEGER	read-write	Additional 802.11 ACK timeout in microseconds. This must be set to non-zero value for radio distances larger than about 700m. Recommended setting is about 10 microseconds per kilometer.
INT artemRadioAntennaDiversity	1.3.6.1.4.1.4280.5.3.1.5	INTEGER	read-write	This attribute selects the mode of antenna diversity. none(0) - No diversity, the main antenna is always used for transmission and receival. receive(1) - The main antenna is always used for transmission. Both main and aux antennas are used for receival, depending on signal levels. transmit(2) - The main antenna is always used for receival. Both main and aux antennas are used for transmission. both(3) - Both main and aux antennas are used for transmission and receival, depending on signal levels.
INT artemRadioChannel	1.3.6.1.4.1.4280.5.3.1.2	INTEGER	read-write	Selecting a radio channel by writing this attribute implicitly defines the radio band to use. Channels 1..14 implies 2.4 GHz Channels 30.. implies 5 GHz Selecting any channel outside the ranges above selects 2.4 GHz with DFS. Is the selected channel part of a DFS-only subband or is it outside of any allowed subband, then DFS will be activated. Reading this attribute always returns the actually working channel, even with DFS. A returned value of 0 means no channel has (yet) been selected, perhaps due to 5 GHz band scanning.
INT artemRadioIndex	1.3.6.1.4.1.4280.5.3.1.1	INTEGER	not-accessible	The auxiliary variable used to identify instances of the columnar objects in the artemRadioParametersTable.
T/F artemRadioNitroMode	1.3.6.1.4.1.4280.5.3.1.6	TruthValue	read-write	This attribute enables Conexant proprietary (but 100% 802.11g standard interoperable) frame bursting for increased data throughput, especially with mixed operation of 802.11b and 802.11g stations.
INT artemRadioOperatingMode	1.3.6.1.4.1.4280.5.3.1.9	INTEGER	read-write	This attribute selects the operation mode for this radio. accessPoint(1) - select access point mode. bridge(2) - select bridge mode, up to 6 bridge links may be generated. doubleBridge(3) - selects double bridge mode. Only available with 802.11b products.
artemRadioParametersEntry	1.3.6.1.4.1.4280.5.3.1		not-accessible	An entry in artemRadioParametersTable.
artemRadioParametersTable	1.3.6.1.4.1.4280.5.3		not-accessible	Table of WLAN radio parameters not covered in standard 802.11 MIB.
INT artemRadioSpeedMode	1.3.6.1.4.1.4280.5.3.1.3	INTEGER	read-write	This attribute selects the data rate to be used for transmissions. Selecting autoFallback activates automatic adaption of the data rate to the transmission conditions.
INT artemRadioTxPower	1.3.6.1.4.1.4280.5.3.1.4	INTEGER	read-write	Transmit power in dBm.
INT artemRadioWwrMode	1.3.6.1.4.1.4280.5.3.1.8	INTEGER	read-write	This attribute enables/disables 802.11d and 802.11h support. none(0) - 802.11d disabled, 802.11h disabled. wwr11d(1) - 802.11d enabled, 802.11h disabled. wwr11d11hFlexible(2) - 802.11d enabled, 802.11h enabled; access point allows non-spectrum-management capable clients to join. wwr11dhStrict(3) - 802.11d enabled, 802.11h enabled; access point requires clients to be spectrum-management capable.
artemWLAN	1.3.6.1.4.1.4280.5			Definitions and attributes that apply to a radio module. The radio module may host one or more interfaces (AP service sets or bridge links).
artemWLANGroup	1.3.6.1.4.1.4280.5.9			Extended WLAN radio parameters not covered in standard 802.11 MIB.
artemWLANNotification	1.3.6.1.4.1.4280.5.8
INT artemWLANRadioIndex	1.3.6.1.4.1.4280.5.4.1.1	INTEGER	read-only	The auxiliary variable used to identify instances of the columnar objects in the artemRadioParametersTable.

RFC description

WLAN management for Artem products providing additional attributes for radio module interfaces.

Start monitoring Funkwerk (artem) ComPoint 802.11 WLAN access points (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ARTEM-COMPOINT-WLAN-MIB