APPN-MIB

All MIBs › APPN-MIB

Organization: IETF SNA NAU MIB WG / AIW APPN MIBs SIG

Last Updated: 1998-07-15

Category: Routing Protocols, SNA and Legacy Protocols

Description: Defines managed objects for monitoring and controlling network devices with SNA Advanced Peer-to-Peer Networking (APPN) capabilities, including topology, sessions, and routing.

IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring APPN-MIB with a free 30-day trial of IPNetwork Monitor.

What Is APPN-MIB?

APPN-MIB is a standards-based IETF module (RFC 2455-family) for managing network devices that implement IBM's SNA Advanced Peer-to-Peer Networking (APPN) architecture, used in legacy mainframe and midrange SNA networking environments. It exposes node identity and topology data, session pacing and routing configuration, and performance counters for high-performance routing (HPR) route setups and rejections. Notably it includes appnNodeUpTime for device uptime tracking and counters such as appnNodeHprIntRteSetups/Rejects that reveal whether APPN route establishment is succeeding or failing, making it useful for monitoring both the operational health and configuration state of APPN-capable network nodes. As a vendor-neutral IETF MIB it is designed to be used alongside standard SNMP frameworks and does not depend on a specific vendor's proprietary extensions, though it is most relevant to devices that also implement SNA/APPN stacks. It is deployed in legacy enterprise networks still running IBM SNA/APPN traffic, typically on routers or gateways bridging SNA and IP environments. Engineers implementing or auditing this functionality typically reference the APPN-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in APPN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB, not tied to a specific manufacturer
SNA/APPN-capable router or network node

Monitoring Examples

An operator would poll appnNodeUpTime and appnNodeCpName/appnNodeId to confirm node identity and stability, then check appnNodeHprIntRteSetups against appnNodeHprIntRteRejects (and the org-route equivalents) to see whether HPR route establishment attempts are succeeding. Objects like appnNodeMaxSessPerRtpConn and appnNodeAdaptiveBindPacing reveal session capacity and flow-control tuning under appnNn/appnNnTopo. A rising ratio of appnNodeHprIntRteRejects relative to setups would indicate topology or resource problems preventing APPN sessions from establishing.

What Can Be Monitored

node uptime
APPN node identity/type
HPR route setup successes and rejections
session pacing/capacity configuration
network topology (node/topology database)

Imported Objects

From IANAifType-MIB

IANAifType

From SNA-NAU-MIB

snanauMIB

MODULE-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowPointer
TEXTUAL-CONVENTION
TimeStamp
TruthValue
VariablePointer

OIDs

OID symbolic	OID numeric	Type	Access	Description
NUM affectedObject	1.3.6.1.2.1.34.4.2.3	VariablePointer	accessible-for-notify	The MIB object associated with the Alert condition, if there is an object associated with it. If no associated object can be identified, the value 0.0 is passed in the trap.
OCT alertIdNumber	1.3.6.1.2.1.34.4.2.2	OCTET STRING	accessible-for-notify	A 32-bit SNA Management Services (SNA/MS) Alert ID Number, as specified in SNA/MS Formats.
NTF alertTrap	1.3.6.1.2.1.34.4.2.1			This trap carries a 32-bit SNA Management Services (SNA/MS) Alert ID Number, as specified in SNA/MS Formats.
appnBrNnConfGroup	1.3.6.1.2.1.34.4.3.2.20			A collection of objects providing instrumentation for branch network nodes. Some of these objects also appear in the instrumentation for an end node. Note: A branch network node always returns endNode(2) as the value of the appnNodeType object from the appnGeneralConfGroup2 conformance group.
appnCompliance	1.3.6.1.2.1.34.4.3.1.1			The compliance statement for the SNMPv2 entities that implement the APPN MIB. This is the compliance statement for the RFC 2155-level version of the APPN MIB. It was deprecated as new objects were added to the MIB for MLTG, branch network node, and other extensions to the APPN architecture.
appnCompliance2	1.3.6.1.2.1.34.4.3.1.3			The compliance statement for the SNMPv2 entities that implement the APPN MIB. In the descriptions for the conditionally mandatory groups that follow, the branch network node is treated as a third node type, parallel to network node and end node. This is not how branch network nodes are treated in the base APPN architecture, but it increases clarity here to do it.
appnCompliances	1.3.6.1.2.1.34.4.3.1
appnConformance	1.3.6.1.2.1.34.4.3
appnCos	1.3.6.1.2.1.34.4.1.5
appnCosConfGroup	1.3.6.1.2.1.34.4.3.2.12			The appnCosConfGroup is mandatory only for APPN network nodes and end nodes.
SNA appnCosModeCosName	1.3.6.1.2.1.34.4.1.5.1.1.2	SnaClassOfServiceName	read-only	Administratively assigned name for this class of service.
appnCosModeEntry	1.3.6.1.2.1.34.4.1.5.1.1		not-accessible	This table is indexed by the mode name.
SNA appnCosModeName	1.3.6.1.2.1.34.4.1.5.1.1.1	SnaModeName	not-accessible	Administratively assigned name for this mode.
appnCosModeTable	1.3.6.1.2.1.34.4.1.5.1		not-accessible	Table representing all of the defined mode names for this node. The table contains the matching COS name for each mode name.
SNA appnCosName	1.3.6.1.2.1.34.4.1.5.2.1.1	SnaClassOfServiceName	not-accessible	Administratively assigned name for this class of service.
appnCosNameEntry	1.3.6.1.2.1.34.4.1.5.2.1		not-accessible	The COS name is the index to this table.
appnCosNameTable	1.3.6.1.2.1.34.4.1.5.2		not-accessible	Table mapping all of the defined class-of-service names for this node to their network transmission priorities.
appnCosNodeRowEntry	1.3.6.1.2.1.34.4.1.5.3.1		not-accessible	A node entry for a given class of service.
INT appnCosNodeRowIndex	1.3.6.1.2.1.34.4.1.5.3.1.2	INTEGER	not-accessible	Subindex under appnCosNodeRowName, corresponding to a row in the node table for the class of service identified in appnCosNodeRowName. For each class of service, this subindex orders rows in the appnCosNodeRowTable in the same order as that used for route calculation in the APPN node.
INT appnCosNodeRowMaxCongestAllow	1.3.6.1.2.1.34.4.1.5.3.1.7	INTEGER	read-only	Indicates whether low congestion will be tolerated. This object and appnCosNodeRowMinCongestAllow together delineate a range of acceptable congestion states for a node. For the ordered pair (minimum congestion allowed, maximum congestion allowed), the values are interpreted as follows: - (0,0): only low congestion is acceptable - (0,1): either low or high congestion is acceptable - (1,1): only high congestion is acceptable. Note that the combination (1,0) is not defined, since it would identify a range whose lower bound was high congestion and whose upper bound was low congestion.
INT appnCosNodeRowMinCongestAllow	1.3.6.1.2.1.34.4.1.5.3.1.6	INTEGER	read-only	Indicates whether low congestion will be tolerated. This object and appnCosNodeRowMaxCongestAllow together delineate a range of acceptable congestion states for a node. For the ordered pair (minimum congestion allowed, maximum congestion allowed), the values are interpreted as follows: - (0,0): only low congestion is acceptable - (0,1): either low or high congestion is acceptable - (1,1): only high congestion is acceptable. Note that the combination (1,0) is not defined, since it would identify a range whose lower bound was high congestion and whose upper bound was low congestion.
SNA appnCosNodeRowName	1.3.6.1.2.1.34.4.1.5.3.1.1	SnaClassOfServiceName	not-accessible	Administratively assigned name for this class of service.
INT appnCosNodeRowResistMax	1.3.6.1.2.1.34.4.1.5.3.1.5	INTEGER	read-only	Maximum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing.
INT appnCosNodeRowResistMin	1.3.6.1.2.1.34.4.1.5.3.1.4	INTEGER	read-only	Minimum route addition resistance value for this node. Range of values is 0-255. The lower the value, the more desirable the node is for intermediate routing.
appnCosNodeRowTable	1.3.6.1.2.1.34.4.1.5.3		not-accessible	This table contains all node-row information for all classes of service defined in this node.
STR appnCosNodeRowWgt	1.3.6.1.2.1.34.4.1.5.3.1.3	DisplayString	read-only	Weight to be associated with the nodes that fit the criteria specified by this node row. This value can either be a character representation of an integer, or a formula for calculating the weight.
INT appnCosTgRowByteCostMax	1.3.6.1.2.1.34.4.1.5.4.1.9	INTEGER	read-only	Maximum acceptable cost per byte transmitted for this class of service. Cost per byte transmitted: a value representing the relative cost of transmitting a byte over this TG. Range is from 0, which means no cost, to 255.
INT appnCosTgRowByteCostMin	1.3.6.1.2.1.34.4.1.5.4.1.8	INTEGER	read-only	Minimum acceptable cost per byte transmitted for this class of service. Cost per byte transmitted: a value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255.
INT appnCosTgRowConnCostMax	1.3.6.1.2.1.34.4.1.5.4.1.7	INTEGER	read-only	Maximum acceptable cost per connect time for this class of service. Cost per connect time: a value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255.
INT appnCosTgRowConnCostMin	1.3.6.1.2.1.34.4.1.5.4.1.6	INTEGER	read-only	Minimum acceptable cost per connect time for this class of service. Cost per connect time: a value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255.
APP appnCosTgRowDelayMax	1.3.6.1.2.1.34.4.1.5.4.1.13	AppnTgDelay	read-only	Maximum acceptable propagation delay for this class of service.
APP appnCosTgRowDelayMin	1.3.6.1.2.1.34.4.1.5.4.1.12	AppnTgDelay	read-only	Minimum acceptable propagation delay for this class of service.
APP appnCosTgRowEffCapMax	1.3.6.1.2.1.34.4.1.5.4.1.5	AppnTgEffectiveCapacity	read-only	Maximum acceptable capacity for this class of service.
APP appnCosTgRowEffCapMin	1.3.6.1.2.1.34.4.1.5.4.1.4	AppnTgEffectiveCapacity	read-only	Minimum acceptable capacity for this class of service.
appnCosTgRowEntry	1.3.6.1.2.1.34.4.1.5.4.1		not-accessible	A TG entry for a given class of service.
INT appnCosTgRowIndex	1.3.6.1.2.1.34.4.1.5.4.1.2	INTEGER	not-accessible	Subindex under appnCosTgRowName, corresponding to a row in the TG table for the class of service identified in appnCosTgRowName. For each class of service, this subindex orders rows in the appnCosTgRowTable in the same order as that used for route calculation in the APPN node.
SNA appnCosTgRowName	1.3.6.1.2.1.34.4.1.5.4.1.1	SnaClassOfServiceName	not-accessible	Administratively assigned name for this class of service.
APP appnCosTgRowSecurityMax	1.3.6.1.2.1.34.4.1.5.4.1.11	AppnTgSecurity	read-only	Maximum acceptable security for this class of service.
APP appnCosTgRowSecurityMin	1.3.6.1.2.1.34.4.1.5.4.1.10	AppnTgSecurity	read-only	Minimum acceptable security for this class of service.
appnCosTgRowTable	1.3.6.1.2.1.34.4.1.5.4		not-accessible	Table containing all the TG-row information for all classes of service defined in this node.
INT appnCosTgRowUsr1Max	1.3.6.1.2.1.34.4.1.5.4.1.15	INTEGER	read-only	Maximum acceptable value for this user-defined characteristic.
INT appnCosTgRowUsr1Min	1.3.6.1.2.1.34.4.1.5.4.1.14	INTEGER	read-only	Minimum acceptable value for this user-defined characteristic.
INT appnCosTgRowUsr2Max	1.3.6.1.2.1.34.4.1.5.4.1.17	INTEGER	read-only	Maximum acceptable value for this user-defined characteristic.
INT appnCosTgRowUsr2Min	1.3.6.1.2.1.34.4.1.5.4.1.16	INTEGER	read-only	Minimum acceptable value for this user-defined characteristic.
INT appnCosTgRowUsr3Max	1.3.6.1.2.1.34.4.1.5.4.1.19	INTEGER	read-only	Maximum acceptable value for this user-defined characteristic.
INT appnCosTgRowUsr3Min	1.3.6.1.2.1.34.4.1.5.4.1.18	INTEGER	read-only	Minimum acceptable value for this user-defined characteristic.
STR appnCosTgRowWgt	1.3.6.1.2.1.34.4.1.5.4.1.3	DisplayString	read-only	Weight to be associated with the TGs that fit the criteria specified by this TG row. This value can either be a character representation of an integer, or a formula for calculating the weight.
INT appnCosTransPriority	1.3.6.1.2.1.34.4.1.5.2.1.2	INTEGER	read-only	Transmission priority for this class of service: low(1) - (X'01'): low priority medium(2) - (X'02'): medium priority high(3) - (X'03'): high priority network(4) - (X'04'): network priority
appnDir	1.3.6.1.2.1.34.4.1.4
STR appnDirApparentLuOwnerName	1.3.6.1.2.1.34.4.1.4.2.1.6	DisplayString	read-only	Fully qualified CP name of the node at which the LU appears to be located. This object and the appnDirLuOwnerName object are related as follows: Implementations that support this object save in their directory database information about an LU's owning control point that was communicated in two control vectors: - an Associated Resource Entry (X'3C') CV with resource type X'00F4' (ENCP) - a Real Owning Control Point (X'4A') CV. The X'4A' CV is created by a branch network node to preserve the name of the real owning control point for an LU below the branch network node, before it overwrites this name with its own name in the X'3C' CV. The X'4A' CV is not present for LUs that are not below branch network nodes. If the information a node has about an LU's owning CP came only in a X'3C' CV, then the name from the X'3C' is returned in the appnDirLuOwnerName object, and a null string is returned in this object. If the information a node has about an LU's owning CP came in both X'3C' and X'4A' CVs, then the name from the X'4A' is returned in the appnDirLuOwnerName object, and the name from the X'3C' (which will be the branch network node's name) is returned in this object.
G32 appnDirCurCaches	1.3.6.1.2.1.34.4.1.4.1.2	Gauge32	read-only	Current number of cache entries.
G32 appnDirCurHomeEntries	1.3.6.1.2.1.34.4.1.4.1.3	Gauge32	read-only	Current number of home entries.
appnDirEntry	1.3.6.1.2.1.34.4.1.4.2.1		not-accessible	This table is indexed by the LU name.
NUM appnDirInBcastLocates	1.3.6.1.2.1.34.4.1.4.1.6	AppnNodeCounter	read-only	Number of broadcast Locates received since the node was last reinitialized.
NUM appnDirInLocates	1.3.6.1.2.1.34.4.1.4.1.5	AppnNodeCounter	read-only	Number of directed Locates received since the node was last reinitialized.
G32 appnDirLocateOutstands	1.3.6.1.2.1.34.4.1.4.1.11	Gauge32	read-only	Current number of outstanding Locates, both directed and broadcast. This value varies. A value of zero indicates that no Locates are unanswered.
INT appnDirLuLocation	1.3.6.1.2.1.34.4.1.4.2.1.4	INTEGER	read-only	Specifies the location of the LU with respect to the local node.
STR appnDirLuName	1.3.6.1.2.1.34.4.1.4.2.1.1	DisplayString	not-accessible	Fully qualified network LU name in the domain of the serving network node. Entries take one of three forms: - Explicit entries do not contain the character ''. - Partial wildcard entries have the form 'ccc', where 'ccc' represents one to sixteen characters in a legal SNA LuName. - A full wildcard entry consists of the single character '*'
NUM appnDirLuOwnerName	1.3.6.1.2.1.34.4.1.4.2.1.3	SnaControlPointName	read-only	Fully qualified CP name of the node at which the LU is located. This name is the same as the serving NN name when the LU is located at a network node. It is also the same as the fully qualified LU name when this is the control point LU for this node.
U32 appnDirMaxCaches	1.3.6.1.2.1.34.4.1.4.1.1	Unsigned32	read-only	Maximum number of cache entries allowed. This is an administratively assigned value.
NUM appnDirNnServerName	1.3.6.1.2.1.34.4.1.4.2.1.2	SnaControlPointName	read-only	Fully qualified control point (CP) name of the network node server. For unassociated end node entries, a zero-length string is returned.
NUM appnDirNotFoundBcastLocates	1.3.6.1.2.1.34.4.1.4.1.10	AppnNodeCounter	read-only	Number of broadcast Locates returned with a 'not found' since the node was last reinitialized.
NUM appnDirNotFoundLocates	1.3.6.1.2.1.34.4.1.4.1.9	AppnNodeCounter	read-only	Number of directed Locates returned with a 'not found' since the node was last reinitialized.
NUM appnDirOutBcastLocates	1.3.6.1.2.1.34.4.1.4.1.8	AppnNodeCounter	read-only	Number of broadcast Locates sent since the node was last reinitialized.
NUM appnDirOutLocates	1.3.6.1.2.1.34.4.1.4.1.7	AppnNodeCounter	read-only	Number of directed Locates sent since the node was last reinitialized.
appnDirPerf	1.3.6.1.2.1.34.4.1.4.1
G32 appnDirRegEntries	1.3.6.1.2.1.34.4.1.4.1.4	Gauge32	read-only	Current number of registered entries.
appnDirTable	1.3.6.1.2.1.34.4.1.4.2		not-accessible	Table containing information about all known LUs.
appnDirTableConfGroup	1.3.6.1.2.1.34.4.3.2.5			A collection of objects providing the instrumentation of the APPN directory database. This RFC 2155-level group was deprecated when the appnDirApparentLuOwnerName object was added.
appnDirTableConfGroup2	1.3.6.1.2.1.34.4.3.2.29			A collection of objects providing the instrumentation of the APPN directory database.
INT appnDirType	1.3.6.1.2.1.34.4.1.4.2.1.5	INTEGER	read-only	Directory types are: 1 - Home The LU is in the domain of the local node, and the LU information has been configured at the local node. 2 - Cache The LU has previously been located by a broadcast search, and the location information has been saved. 3 - Registered The LU is at an end node that is in the domain of the local network node. Registered entries are registered by the served end node.
appnEnUniqueCaps	1.3.6.1.2.1.34.4.1.1.3
appnEnUniqueConfGroup	1.3.6.1.2.1.34.4.3.2.7			A collection of objects providing instrumentation for APPN end nodes. Some of these objects also appear in the instrumentation for a branch network node.
appnGeneralConfGroup	1.3.6.1.2.1.34.4.3.2.1			A collection of objects providing the instrumentation of APPN general information and capabilities. This RFC 2155-level group was deprecated when the appnNodeMibVersion object was removed and the appnNodeLsCounterType and appnNodeBrNn objects were added.
appnGeneralConfGroup2	1.3.6.1.2.1.34.4.3.2.26			A collection of objects providing the instrumentation of APPN general information and capabilities.
appnGeneralInfoAndCaps	1.3.6.1.2.1.34.4.1.1.1
appnGroups	1.3.6.1.2.1.34.4.3.2
appnHprBaseConfGroup	1.3.6.1.2.1.34.4.3.2.14			The appnHprBaseConfGroup is mandatory only for nodes that implement the HPR base (APPN option set 1400).
appnHprBfConfGroup	1.3.6.1.2.1.34.4.3.2.17			The appnHprBfConfGroup is mandatory only for nodes that implement the APPN/HPR boundary function.
appnHprCtrlFlowsRtpConfGroup	1.3.6.1.2.1.34.4.3.2.16			The appnHprCtrlFlowsRtpConfGroup is mandatory only for nodes that implement the HPR Control Flows over RTP tower (APPN option set 1402).
appnHprRtpConfGroup	1.3.6.1.2.1.34.4.3.2.15			The appnHprRtpConfGroup is mandatory only for nodes that implement the HPR RTP tower (APPN option set 1401).
appnIntSessConfGroup	1.3.6.1.2.1.34.4.3.2.13			The appnIntSessConfGroup is mandatory only for network nodes.
SNA appnIsInCosName	1.3.6.1.2.1.34.4.1.6.2.1.7	SnaClassOfServiceName	read-only	The Class of Service (COS) name used for this session.
TIK appnIsInCtrUpTime	1.3.6.1.2.1.34.4.1.6.2.1.11	TimeTicks	read-only	Length of time the session counters have been active, measured in hundredths of a second.
appnIsInEntry	1.3.6.1.2.1.34.4.1.6.2.1		not-accessible	Entry of Intermediate Session Information Table.
NUM appnIsInFqCpName	1.3.6.1.2.1.34.4.1.6.2.1.1	SnaControlPointName	not-accessible	The network-qualified control point name of the node at which the session and PCID originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. For resources served by a dependent LU requester (DLUR), it is the name of the owning system services control point (SSCP).
appnIsInGlobal	1.3.6.1.2.1.34.4.1.6.1
G32 appnIsInGlobeActSess	1.3.6.1.2.1.34.4.1.6.1.6	Gauge32	read-only	The number of currently active intermediate sessions.
INT appnIsInGlobeCtrAdminStatus	1.3.6.1.2.1.34.4.1.6.1.1	INTEGER	read-write	Object by which a Management Station can deactivate or activate capture of intermediate-session counts and names, by setting the value to notActive(1) or active(2), respectively. The value ready(3) is returned on GET operations until a SET has been processed; after that the value received on the most recent SET is returned. The counts referred to here are the eight objects in the AppnIsInTable, from appnIsInP2SFmdPius through appnIsInS2PNonFmdBytes. The names are the four objects in this table, from appnIsInPriLuName through appnIsInCosName. Setting this object to the following values has the following effects: notActive(1) stop collecting count data. If a count is queried, it returns the value 0. Collection of names may, but need not be, disabled. active(2) start collecting count data. If it is supported, collection of names is enabled.
INT appnIsInGlobeCtrOperStatus	1.3.6.1.2.1.34.4.1.6.1.2	INTEGER	read-only	Indicates whether or not the intermediate session counts are active. The counts referred to here are the eight objects in the AppnIsInTable, from appnIsInP2SFmdPius through appnIsInS2PNonFmdBytes. These eight counts are of type Unsigned32 rather than Counter32 because when this object enters the notActive state, either because a Management Station has set appnInInGlobeCtrAdminStatus to notActive or because of a locally-initiated transition, the counts are all reset to 0. The values for this object are: notActive(1): collection of counts is not active; if it is queried, a count returns the value 0. active(2): collection of counts is active.
TIK appnIsInGlobeCtrStatusTime	1.3.6.1.2.1.34.4.1.6.1.3	TimeTicks	read-only	The time since the appnIsInGlobeCtrOperStatus object last changed, measured in hundredths of a second. This time can be used to identify when this change occurred in relation to other events in the agent, such as the last time the APPN node was reinitialized.
G32 appnIsInGlobeHprBfActSess	1.3.6.1.2.1.34.4.1.6.1.7	Gauge32	read-only	The number of currently active HPR intermediate sessions.
INT appnIsInGlobeRscv	1.3.6.1.2.1.34.4.1.6.1.4	INTEGER	read-write	Indicates the current route selection control vector (RSCV) collection option in effect, and allows a Management Station to change the option. The values for this object are: notActive(1): collection of route selection control vectors is not active. active(2): collection of route selection control vectors is active.
TIK appnIsInGlobeRscvTime	1.3.6.1.2.1.34.4.1.6.1.5	TimeTicks	read-only	The time since the appnIsInGlobeRscv object last changed, measured in hundredths of a second. This time can be used to identify when this change occurred in relation to other events in the agent, such as the last time the APPN node was reinitialized.
SNA appnIsInModeName	1.3.6.1.2.1.34.4.1.6.2.1.6	SnaModeName	read-only	The mode name used for this session.
U32 appnIsInP2SFmdBytes	1.3.6.1.2.1.34.4.1.6.2.1.16	Unsigned32	read-only	Number of FMD bytes sent from the Primary LU to the Secondary LU since the counts were last activated.
U32 appnIsInP2SFmdPius	1.3.6.1.2.1.34.4.1.6.2.1.12	Unsigned32	read-only	Number of function management data (FMD) path information units (PIUs) sent from the Primary LU to the Secondary LU since the counts were last activated.
U32 appnIsInP2SNonFmdBytes	1.3.6.1.2.1.34.4.1.6.2.1.18	Unsigned32	read-only	Number of non-FMD bytes sent from the Primary LU to the Secondary LU since the counts were last activated.
U32 appnIsInP2SNonFmdPius	1.3.6.1.2.1.34.4.1.6.2.1.14	Unsigned32	read-only	Number of non-FMD PIUs sent from the Primary LU to the Secondary LU since the counts were last activated.
OCT appnIsInPcid	1.3.6.1.2.1.34.4.1.6.2.1.2	OCTET STRING	not-accessible	The procedure correlation identifier (PCID) of a session. It is an 8-byte value assigned by the primary LU.
STR appnIsInPriLuName	1.3.6.1.2.1.34.4.1.6.2.1.4	DisplayString	read-only	The primary LU name of the session. A zero-length string indicates that this name is not available.
NUM appnIsInPsAdjCpName	1.3.6.1.2.1.34.4.1.6.2.1.20	SnaControlPointName	read-only	The primary stage adjacent CP name of this session. If the session stage traverses an RTP connection, the CP name of the remote RTP endpoint is returned.
INT appnIsInPsAdjTgNum	1.3.6.1.2.1.34.4.1.6.2.1.21	INTEGER	read-only	The primary stage adjacent transmission group (TG) number associated with this session. If the session stage traverses an RTP connection, the value 256 is returned. Values between 257 and 300 are available for other possible TG 'stand-ins' that may be added to APPN in the future.
G32 appnIsInPsRecvNxWndwSize	1.3.6.1.2.1.34.4.1.6.2.1.28	Gauge32	read-only	The primary stage size of the next window which will be used to receive data.
INT appnIsInPsRecvPacingType	1.3.6.1.2.1.34.4.1.6.2.1.26	INTEGER	read-only	The primary stage type of pacing being used for receiving data.
G32 appnIsInPsRecvRpc	1.3.6.1.2.1.34.4.1.6.2.1.27	Gauge32	read-only	The primary stage receive residual pace count. This represents the primary stage number of message units (MUs) that can still be received in the current session window.
INT appnIsInPsSendMaxBtuSize	1.3.6.1.2.1.34.4.1.6.2.1.22	INTEGER	read-only	The primary stage maximum basic transmission unit (BTU) size for sending data.
G32 appnIsInPsSendNxWndwSize	1.3.6.1.2.1.34.4.1.6.2.1.25	Gauge32	read-only	The primary stage size of the next window which will be used to send data.
INT appnIsInPsSendPacingType	1.3.6.1.2.1.34.4.1.6.2.1.23	INTEGER	read-only	The primary stage type of pacing being used for sending data.
G32 appnIsInPsSendRpc	1.3.6.1.2.1.34.4.1.6.2.1.24	Gauge32	read-only	The primary stage send residual pace count. This represents the primary stage number of message units (MUs) that can still be sent in the current session window.
OCT appnIsInRouteInfo	1.3.6.1.2.1.34.4.1.6.2.1.38	OCTET STRING	read-only	The route selection control vector (RSCV X'2B') used for this session. It is present for APPN nodes; but is not present for LEN nodes. The format of this vector is described in SNA Formats. If no RSCV is available, a zero-length string is returned.
OCT appnIsInRtpNceId	1.3.6.1.2.1.34.4.1.6.2.1.39	OCTET STRING	read-only	The HPR local Network Connection Endpoint of the session.
OCT appnIsInRtpTcid	1.3.6.1.2.1.34.4.1.6.2.1.40	OCTET STRING	read-only	The RTP connection local TCID of the session.
U32 appnIsInS2PFmdBytes	1.3.6.1.2.1.34.4.1.6.2.1.17	Unsigned32	read-only	Number of FMD bytes sent from the Secondary LU to the Primary LU since the counts were last activated.
U32 appnIsInS2PFmdPius	1.3.6.1.2.1.34.4.1.6.2.1.13	Unsigned32	read-only	Number of FMD PIUs sent from the Secondary LU to the Primary LU since the counts were last activated.
U32 appnIsInS2PNonFmdBytes	1.3.6.1.2.1.34.4.1.6.2.1.19	Unsigned32	read-only	Number of non-FMD bytes sent from the Secondary LU to the Primary LU since the counts were last activated.
U32 appnIsInS2PNonFmdPius	1.3.6.1.2.1.34.4.1.6.2.1.15	Unsigned32	read-only	Number of non-FMD PIUs sent from the Secondary LU to the Primary LU since the counts were last activated.
STR appnIsInSecLuName	1.3.6.1.2.1.34.4.1.6.2.1.5	DisplayString	read-only	The secondary LU name of the session. A zero-length string indicates that this name is not available.
INT appnIsInSessState	1.3.6.1.2.1.34.4.1.6.2.1.3	INTEGER	read-write	Indicates the state of the session: inactive(1) - session is inactive pendactive(2) - session is pending active active(3) - session is active pendinact(4) - session is pending inactive Active sessions can be deactivated by setting this object to inactive(1).
INT appnIsInSessType	1.3.6.1.2.1.34.4.1.6.2.1.9	INTEGER	read-only	The type of intermediate session. Defined values are unknown The session type is not known. lu62 A session between LUs of type 6.2 (as indicated by the LU type in Bind) lu0thru3 A session between LUs of type 0, 1, 2, or 3 (as indicated by the LU type in Bind) lu62dlur A session between LUs of type 6.2 (as indicated by the LU type in Bind). One of the LUs is a dependent LU supported by the dependent LU requester (DLUR) function at this node. lu0thru3dlur A session between LUs of type 0, 1, 2, or 3 (as indicated by the LU type in Bind) One of the LUs is a dependent LU supported by the dependent LU requester (DLUR) function at this node.
TIK appnIsInSessUpTime	1.3.6.1.2.1.34.4.1.6.2.1.10	TimeTicks	read-only	Length of time the session has been active, measured in hundredths of a second.
NUM appnIsInSsAdjCpName	1.3.6.1.2.1.34.4.1.6.2.1.29	SnaControlPointName	read-only	The secondary stage adjacent CP name of this session. If the session stage traverses an RTP connection, the CP name of the remote RTP endpoint is returned.
INT appnIsInSsAdjTgNum	1.3.6.1.2.1.34.4.1.6.2.1.30	INTEGER	read-only	The secondary stage adjacent transmission group (TG) number associated with this session. If the session stage traverses an RTP connection, the value 256 is returned. Values between 257 and 300 are available for other possible TG 'stand-ins' that may be added to APPN in the future.
G32 appnIsInSsRecvNxWndwSize	1.3.6.1.2.1.34.4.1.6.2.1.37	Gauge32	read-only	The secondary stage size of the next window which will be used to receive data.
INT appnIsInSsRecvPacingType	1.3.6.1.2.1.34.4.1.6.2.1.35	INTEGER	read-only	The secondary stage type of pacing being used for receiving data.
G32 appnIsInSsRecvRpc	1.3.6.1.2.1.34.4.1.6.2.1.36	Gauge32	read-only	The secondary stage receive residual pace count. This represents the secondary stage number of message units (MUs) that can still be received in the current session window.
INT appnIsInSsSendMaxBtuSize	1.3.6.1.2.1.34.4.1.6.2.1.31	INTEGER	read-only	The secondary stage maximum basic transmission unit (BTU) size for sending data.
G32 appnIsInSsSendNxWndwSize	1.3.6.1.2.1.34.4.1.6.2.1.34	Gauge32	read-only	The secondary stage size of the next window which will be used to send data.
INT appnIsInSsSendPacingType	1.3.6.1.2.1.34.4.1.6.2.1.32	INTEGER	read-only	The secondary stage type of pacing being used for sending data.
G32 appnIsInSsSendRpc	1.3.6.1.2.1.34.4.1.6.2.1.33	Gauge32	read-only	The secondary stage send residual pace count. This represents the secondary stage number of message units (MUs) that can still be sent in the current session window.
appnIsInTable	1.3.6.1.2.1.34.4.1.6.2		not-accessible	Intermediate Session Information Table
INT appnIsInTransPriority	1.3.6.1.2.1.34.4.1.6.2.1.8	INTEGER	read-only	Transmission priority for this class of service. Values are: low(1) - (X'01'): low priority medium(2) - (X'02'): medium priority high(3) - (X'03'): high priority network(4) - (X'04'): network priority
appnIsRtpEntry	1.3.6.1.2.1.34.4.1.6.3.1		not-accessible	Entry of Intermediate Session RTP Table.
OCT appnIsRtpNceId	1.3.6.1.2.1.34.4.1.6.3.1.1	OCTET STRING	not-accessible	The local Network Connection Endpoint of the RTP connection.
G32 appnIsRtpSessions	1.3.6.1.2.1.34.4.1.6.3.1.3	Gauge32	read-only	The number of intermediate sessions using this RTP connection.
appnIsRtpTable	1.3.6.1.2.1.34.4.1.6.3		not-accessible	A table indicating how many ISR sessions are transported by each RTP connection.
OCT appnIsRtpTcid	1.3.6.1.2.1.34.4.1.6.3.1.2	OCTET STRING	not-accessible	The local TCID of the RTP connection.
appnLinkConfGroup	1.3.6.1.2.1.34.4.3.2.3			A collection of objects providing the instrumentation of APPN link information. This RFC 2155-level group was deprecated when the appnLsMltgMember object was added.
appnLinkConfGroup2	1.3.6.1.2.1.34.4.3.2.27			A collection of objects providing the instrumentation of APPN link information.
appnLinkStationInformation	1.3.6.1.2.1.34.4.1.1.5
appnLocalDirPerfConfGroup	1.3.6.1.2.1.34.4.3.2.11			The appnLocalDirPerfConfGroup is mandatory only for APPN network nodes and end nodes.
INT appnLocalEnTgByteCost	1.3.6.1.2.1.34.4.1.3.2.1.11	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0, which means no cost, to 255.
INT appnLocalEnTgConnCost	1.3.6.1.2.1.34.4.1.3.2.1.10	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
INT appnLocalEnTgCpCpSession	1.3.6.1.2.1.34.4.1.3.2.1.8	INTEGER	read-only	Indicates whether CP-CP sessions are supported on this TG, and whether the TG owner's contention-winner session is active on this TG. Some nodes in the network are not able to differentiate support and status of CP-CP sessions, and thus may report the 'supportedUnknownStatus' value.
APP appnLocalEnTgDelay	1.3.6.1.2.1.34.4.1.3.2.1.13	AppnTgDelay	read-only	Administratively assigned delay associated with this TG.
NUM appnLocalEnTgDest	1.3.6.1.2.1.34.4.1.3.2.1.2	SnaControlPointName	not-accessible	Administratively assigned name of the destination node for this TG. This is the fully qualified name of a network node, end node, LEN node, or virtual routing node.
T/F appnLocalEnTgDestVirtual	1.3.6.1.2.1.34.4.1.3.2.1.5	TruthValue	read-only	Indicates whether the destination node is a virtual routing node.
APP appnLocalEnTgDlcData	1.3.6.1.2.1.34.4.1.3.2.1.6	AppnTgDlcData	read-only	DLC-specific data related to a link connection network.
APP appnLocalEnTgEffCap	1.3.6.1.2.1.34.4.1.3.2.1.9	AppnTgEffectiveCapacity	read-only	Effective capacity for this TG.
appnLocalEnTgEntry	1.3.6.1.2.1.34.4.1.3.2.1		not-accessible	This table requires multiple indexes to uniquely identify each TG. They are originating CPname, destination CPname, and the TG number.
APP appnLocalEnTgEntryTimeLeft	1.3.6.1.2.1.34.4.1.3.2.1.4	AppnTopologyEntryTimeLeft	read-only	Number of days before deletion of this end node TG entry.
T/F appnLocalEnTgMltgLinkType	1.3.6.1.2.1.34.4.1.3.2.1.17	TruthValue	read-only	This object indicates whether the transmission group is a multi-link TG. A TG that has been brought up as a multi-link TG is reported as one, even if it currently has only one link active.
INT appnLocalEnTgNum	1.3.6.1.2.1.34.4.1.3.2.1.3	INTEGER	not-accessible	Number associated with this transmission group.
T/F appnLocalEnTgOperational	1.3.6.1.2.1.34.4.1.3.2.1.7	TruthValue	read-only	Indicates whether the transmission group is operational.
NUM appnLocalEnTgOrigin	1.3.6.1.2.1.34.4.1.3.2.1.1	SnaControlPointName	not-accessible	Administratively assigned name of the origin node for this TG. This is a fully qualified network name.
APP appnLocalEnTgSecurity	1.3.6.1.2.1.34.4.1.3.2.1.12	AppnTgSecurity	read-only	Administratively assigned security level of this TG.
appnLocalEnTgTable	1.3.6.1.2.1.34.4.1.3.2		not-accessible	Table describing all of the TGs owned by the end nodes known to this node via TG registration. This node does not represent its own view of the TG on behalf of the partner node in this table. The TG destination can be a virtual routing node, network node, or end node.
INT appnLocalEnTgUsr1	1.3.6.1.2.1.34.4.1.3.2.1.14	INTEGER	read-only	First user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG.
INT appnLocalEnTgUsr2	1.3.6.1.2.1.34.4.1.3.2.1.15	INTEGER	read-only	Second user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG.
INT appnLocalEnTgUsr3	1.3.6.1.2.1.34.4.1.3.2.1.16	INTEGER	read-only	Third user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG.
appnLocalEnTopoConfGroup	1.3.6.1.2.1.34.4.3.2.10			The appnLocalEnTopoConfGroup is mandatory only for network nodes. This RFC 2155-level group was deprecated when the appnLocalEnTgMltgLinkType object was added.
appnLocalEnTopoConfGroup2	1.3.6.1.2.1.34.4.3.2.31			A collection of objects providing the instrumentation of the information that a network node possesses about the end nodes directly attached to it.
INT appnLocalTgBranchLinkType	1.3.6.1.2.1.34.4.1.3.1.1.20	INTEGER	read-only	Branch link type of this TG: other(1) = the agent has determined the TG's branch link type to be a value other than branch uplink or branch downlink. This is the value used for a connection network TG owned by a branch network node. uplink(2) = the TG is a branch uplink. downlink(3) = the TG is a branch downlink to an end node. downlinkToBranchNetworkNode(4) = the TG is a branch downlink to a cascaded branch network node. none(5) = the TG is not a branch TG. unknown(255) = the agent cannot determine the branch link type of the TG.
INT appnLocalTgByteCost	1.3.6.1.2.1.34.4.1.3.1.1.11	INTEGER	read-only	Relative cost of transmitting a byte over this link. Range is from 0 (lowest cost) to 255.
appnLocalTgConfGroup	1.3.6.1.2.1.34.4.3.2.4			A collection of objects providing the instrumentation of APPN local TG information. This RFC 2155-level group was deprecated when the appnLocalTgMltgLinkType object was added.
appnLocalTgConfGroup2	1.3.6.1.2.1.34.4.3.2.28			A collection of objects providing the instrumentation of APPN local TG information.
INT appnLocalTgConnCost	1.3.6.1.2.1.34.4.1.3.1.1.10	INTEGER	read-only	Cost per connect time: a value representing the relative cost per unit of time to use the TG. Range is from 0, which means no cost, to 255.
INT appnLocalTgCpCpSession	1.3.6.1.2.1.34.4.1.3.1.1.8	INTEGER	read-only	Indicates whether CP-CP sessions are supported on this TG, and whether the TG owner's contention-winner session is active on this TG. Some nodes in the network are not able to differentiate support and status of CP-CP sessions, and thus may report the 'supportedUnknownStatus' value.
APP appnLocalTgDelay	1.3.6.1.2.1.34.4.1.3.1.1.13	AppnTgDelay	read-only	Administratively assigned delay associated with this TG.
NUM appnLocalTgDest	1.3.6.1.2.1.34.4.1.3.1.1.1	SnaControlPointName	not-accessible	Administratively assigned name of the destination node for this TG. This is the fully qualified name of a network node, end node, LEN node, or virtual routing node.
T/F appnLocalTgDestVirtual	1.3.6.1.2.1.34.4.1.3.1.1.3	TruthValue	read-only	Indicates whether the destination node for this TG is a virtual routing node.
APP appnLocalTgDlcData	1.3.6.1.2.1.34.4.1.3.1.1.4	AppnTgDlcData	read-only	DLC-specific data related to a link connection network.
APP appnLocalTgEffCap	1.3.6.1.2.1.34.4.1.3.1.1.9	AppnTgEffectiveCapacity	read-only	Effective capacity for this TG.
appnLocalTgEntry	1.3.6.1.2.1.34.4.1.3.1.1		not-accessible	This table is indexed by the destination CpName and the TG number.
INT appnLocalTgHprSup	1.3.6.1.2.1.34.4.1.3.1.1.17	INTEGER	read-only	Indicates the level of high performance routing (HPR) support over this TG : noHprSupport(1) - no HPR support hprBaseOnly(2) - HPR base (option set 1400) supported rtpTower(3) - HPR base and RTP tower (option set 1401) supported controlFlowsOverRtpTower(4) - HPR base, RTP tower, and control flows over RTP (option set 1402) supported
T/F appnLocalTgIntersubnet	1.3.6.1.2.1.34.4.1.3.1.1.18	TruthValue	read-only	Indicates whether the transmission group is an intersubnet TG, which defines a border between subnetworks.
T/F appnLocalTgMltgLinkType	1.3.6.1.2.1.34.4.1.3.1.1.19	TruthValue	read-only	This object indicates whether the transmission group is a multi-link TG. A TG that has been brought up as a multi-link TG is reported as one, even if it currently has only one link active.
INT appnLocalTgNum	1.3.6.1.2.1.34.4.1.3.1.1.2	INTEGER	not-accessible	Number associated with this transmission group.
T/F appnLocalTgOperational	1.3.6.1.2.1.34.4.1.3.1.1.7	TruthValue	read-only	Indicates whether the transmission group is operational.
STR appnLocalTgPortName	1.3.6.1.2.1.34.4.1.3.1.1.5	DisplayString	read-only	Administratively assigned name for the local port associated with this TG. A zero-length string indicates that this value is unknown.
T/F appnLocalTgQuiescing	1.3.6.1.2.1.34.4.1.3.1.1.6	TruthValue	read-only	Indicates whether the transmission group is quiescing.
APP appnLocalTgSecurity	1.3.6.1.2.1.34.4.1.3.1.1.12	AppnTgSecurity	read-only	Administratively assigned security level of this TG.
appnLocalTgTable	1.3.6.1.2.1.34.4.1.3.1		not-accessible	TG Table describes all of the TGs owned by this node. The TG destination can be a virtual node, network node, LEN node, or end node.
INT appnLocalTgUsr1	1.3.6.1.2.1.34.4.1.3.1.1.14	INTEGER	read-only	First user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG.
INT appnLocalTgUsr2	1.3.6.1.2.1.34.4.1.3.1.1.15	INTEGER	read-only	Second user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG.
INT appnLocalTgUsr3	1.3.6.1.2.1.34.4.1.3.1.1.16	INTEGER	read-only	Third user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG.
appnLocalTopology	1.3.6.1.2.1.34.4.1.3
U32 appnLsActiveTime	1.3.6.1.2.1.34.4.1.1.5.1.1.32	Unsigned32	read-only	The cumulative amount of time since the node was last reinitialized, measured in hundredths of a second, that this link station has been in the active state. A zero value indicates that the link station has never been active since the node was last reinitialized.
T/F appnLsActOnDemand	1.3.6.1.2.1.34.4.1.1.5.1.1.11	TruthValue	read-only	Indicates whether the link station is activatable on demand. Such a link station is reported in the topology as active regardless of its actual state, so that it can be considered in route calculations. If the link station is inactive and is chosen for a route, it will be activated at that time.
OCT appnLsAdjCpName	1.3.6.1.2.1.34.4.1.1.5.1.1.7	OCTET STRING	read-only	Fully qualified name of the adjacent node for this link station. An adjacent node is identified using the format specified in the SnaControlPointName textual convention. The value of this object is determined as follows: 1. If the adjacent node's name was received on XID, it is returned. 2. If the adjacent node's name was not received on XID, but a locally-defined value is available, it is returned. 3. Otherwise a string of length 0 is returned, indicating that no name is known for the adjacent node.
INT appnLsAdjNodeType	1.3.6.1.2.1.34.4.1.1.5.1.1.8	INTEGER	read-only	Node type of the adjacent node on this link: networkNode(1) - APPN network node endNode(2) - APPN end node t21len(4) - LEN end node unknown(255) - the agent does not know the node type of the adjacent node
NUM appnLsBadXids	1.3.6.1.2.1.34.4.1.1.5.1.1.30	AppnLinkStationCounter	read-only	The total number of unsuccessful XID exchanges that have occurred on this link station since the time it was started.
OCT appnLsBfNceId	1.3.6.1.2.1.34.4.1.1.5.1.1.40	OCTET STRING	read-only	The network connection endpoint identifier (NCE ID) for the APPN/HPR boundary function if this node supports the HPR transport tower, a zero-length string if the value is unknown or not meaningful for this node.
INT appnLsCommand	1.3.6.1.2.1.34.4.1.1.5.1.1.2	INTEGER	read-write	Object by which a Management Station can activate, deactivate, or recycle (i.e., cause to be deactivated and then immediately reactivated) a link station, by setting the value to activate(1), deactivate(2), or recycle(3), respectively. The value ready(4) is returned on GET operations until a SET has been processed; after that the value received on the most recent SET is returned.
TIM appnLsCounterDisconTime	1.3.6.1.2.1.34.4.1.1.5.1.1.44	TimeStamp	read-only	The value of the sysUpTime object the last time the link station was started.
OCT appnLsCpCpNceId	1.3.6.1.2.1.34.4.1.1.5.1.1.38	OCTET STRING	read-only	The network connection endpoint identifier (NCE ID) for CP-CP sessions if this node supports the HPR transport tower, a zero-length string if the value is unknown or not meaningful for this node.
T/F appnLsCpCpSessionSupport	1.3.6.1.2.1.34.4.1.1.5.1.1.14	TruthValue	read-only	Indicates whether CP-CP sessions are supported by this link station. For a dynamic link, this object represents the default ('Admin') value.
G32 appnLsCurrentDelay	1.3.6.1.2.1.34.4.1.1.5.1.1.25	Gauge32	read-only	The time that it took for the last test signal to be sent and returned from this link station to the adjacent link station. This time is represented in milliseconds.
TIK appnLsCurrentStateTime	1.3.6.1.2.1.34.4.1.1.5.1.1.33	TimeTicks	read-only	The amount of time, measured in hundredths of a second, that the link station has been in its current state.
IAN appnLsDlcType	1.3.6.1.2.1.34.4.1.1.5.1.1.5	IANAifType	read-only	The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
T/F appnLsDynamic	1.3.6.1.2.1.34.4.1.1.5.1.1.6	TruthValue	read-only	Identifies whether this is a dynamic link station. Dynamic link stations are created when links that have not been locally defined are established by adjacent nodes.
NUM appnLsEchoRsps	1.3.6.1.2.1.34.4.1.1.5.1.1.24	AppnLinkStationCounter	read-only	Number of echo responses returned from adjacent link station. A response should be returned for each test frame sent by this node. Test frames are sent to adjacent nodes periodically to verify connectivity and to measure the actual round trip time, that is, the time interval from when the test frame is sent until when the response is received.
appnLsEntry	1.3.6.1.2.1.34.4.1.1.5.1.1		not-accessible	This table is indexed by the link station name.
T/F appnLsErrRecoSup	1.3.6.1.2.1.34.4.1.1.5.1.1.35	TruthValue	read-only	Indicates whether the link station is supporting HPR link-level error recovery.
OCT appnLsForAnrLabel	1.3.6.1.2.1.34.4.1.1.5.1.1.36	OCTET STRING	read-only	The forward Automatic Network Routing (ANR) label for this link station. If the link does not support HPR or the value is unknown, a zero-length string is returned.
NUM appnLsGoodXids	1.3.6.1.2.1.34.4.1.1.5.1.1.29	AppnLinkStationCounter	read-only	The total number of successful XID exchanges that have occurred on this link station since the time it was started.
INT appnLsHprSup	1.3.6.1.2.1.34.4.1.1.5.1.1.34	INTEGER	read-only	Indicates the level of high performance routing (HPR) support over this link: noHprSupport(1) - no HPR support hprBaseOnly(2) - HPR base (option set 1400) supported rtpTower(3) - HPR base and RTP tower (option set 1401) supported controlFlowsOverRtpTower(4) - HPR base, RTP tower, and control flows over RTP (option set 1402) supported If the link is not active, the defined value is returned.
NUM appnLsInMsgBytes	1.3.6.1.2.1.34.4.1.1.5.1.1.17	AppnLinkStationCounter	read-only	Number of message (I-frame) bytes received. All of the bytes in the SNA basic transmission unit (BTU), including the transmission header (TH), are counted.
NUM appnLsInMsgFrames	1.3.6.1.2.1.34.4.1.1.5.1.1.19	AppnLinkStationCounter	read-only	Number of message (I-frame) frames received.
NUM appnLsInXidBytes	1.3.6.1.2.1.34.4.1.1.5.1.1.16	AppnLinkStationCounter	read-only	Number of XID bytes received. All of the bytes in the SNA basic transmission unit (BTU), i.e., all of the bytes in the DLC XID Information Field, are counted.
NUM appnLsInXidFrames	1.3.6.1.2.1.34.4.1.1.5.1.1.18	AppnLinkStationCounter	read-only	Number of XID frames received.
T/F appnLsLimResource	1.3.6.1.2.1.34.4.1.1.5.1.1.10	TruthValue	read-only	Indicates whether the link station is a limited resource. A link station that is a limited resource is deactivated when it is no longer in use.
ADR appnLsLocalAddr	1.3.6.1.2.1.34.4.1.1.5.1.1.41	DisplayableDlcAddress	read-only	Local address of this link station.
G32 appnLsMaxDelay	1.3.6.1.2.1.34.4.1.1.5.1.1.26	Gauge32	read-only	The longest time it took for a test signal to be sent and returned from this link station to the adjacent link station. This time is represented in milliseconds . The value 0 is returned if no test signal has been sent and returned.
DAT appnLsMaxDelayTime	1.3.6.1.2.1.34.4.1.1.5.1.1.28	DateAndTime	read-only	The time when the longest delay occurred. This time can be used to identify when this high water mark occurred in relation to other events in the APPN node, for example, the time at which an APPC session was either terminated or failed to be established. This latter time is available in the appcHistSessTime object in the APPC MIB. The value 00000000 is returned if no test signal has been sent and returned.
INT appnLsMaxSendBtuSize	1.3.6.1.2.1.34.4.1.1.5.1.1.15	INTEGER	read-only	Numeric value between 99 and 32767 inclusive indicating the maximum number of bytes in a Basic Transmission Unit (BTU) sent on this link. When the link state (returned by the appnLsOperState object) is inactive or pending active, the value configured at this node is returned. When the link state is active, the value that was negotiated for it is returned. This negotiated value is the smaller of the value configured at this node and the partner's maximum receive BTU length, received in XID.
T/F appnLsMigration	1.3.6.1.2.1.34.4.1.1.5.1.1.12	TruthValue	read-only	Indicates whether this link station will be used for connections to down-level or migration partners. In general, migration nodes do not append their CP names on XID3. Such nodes: (1) will not support parallel TGs, (2) should be sent an ACTIVATE PHYSICAL UNIT (ACTPU), provided that the partner supports ACTPUs, and (3) should not be sent segmented BINDs. However, if this node receives an XID3 with an appended CP name, then the partner node will not be treated as a migration node. In the case of DYNAMIC TGs this object should be set to 'no'.
G32 appnLsMinDelay	1.3.6.1.2.1.34.4.1.1.5.1.1.27	Gauge32	read-only	The shortest time it took for a test signal to be sent and returned from this link station to the adjacent link station. This time is represented in milliseconds. The value 0 is returned if no test signal has been sent and returned.
T/F appnLsMltgMember	1.3.6.1.2.1.34.4.1.1.5.1.1.45	TruthValue	read-only	Indicates whether the link is a member of a multi-link TG. If the link's TG has been brought up as a multi-link TG, then the link is reported as a member of a multi-link TG, even if it is currently the only active link in the TG.
STR appnLsName	1.3.6.1.2.1.34.4.1.1.5.1.1.1	DisplayString	not-accessible	Administratively assigned name for the link station. The name can be from one to ten characters.
INT appnLsOperState	1.3.6.1.2.1.34.4.1.1.5.1.1.3	INTEGER	read-only	State of this link station. The comments map these more granular states to the 'traditional' four states for SNA resources. Values (2) through (5) represent the normal progression of states when a link station is being activated. Value (6) represents some other state of a link station in the process of being activated. Values (8) through (10) represent different ways a link station can be deactivated. Value (11) represents some other state of a link station in the process of being deactivated.
NUM appnLsOutMsgBytes	1.3.6.1.2.1.34.4.1.1.5.1.1.21	AppnLinkStationCounter	read-only	Number of message (I-frame) bytes sent. All of the bytes in the SNA basic transmission unit (BTU), including the transmission header (TH), are counted.
NUM appnLsOutMsgFrames	1.3.6.1.2.1.34.4.1.1.5.1.1.23	AppnLinkStationCounter	read-only	Number of message (I-frame) frames sent.
NUM appnLsOutXidBytes	1.3.6.1.2.1.34.4.1.1.5.1.1.20	AppnLinkStationCounter	read-only	Number of XID bytes sent. All of the bytes in the SNA basic transmission unit (BTU), i.e., all of the bytes in the DLC XID Information Field, are counted.
NUM appnLsOutXidFrames	1.3.6.1.2.1.34.4.1.1.5.1.1.22	AppnLinkStationCounter	read-only	Number of XID frames sent.
SNA appnLsPartnerNodeId	1.3.6.1.2.1.34.4.1.1.5.1.1.13	SnaNodeIdentification	read-only	The partner's Node Identification, from bytes 2-5 of the XID received from the partner. If this value is not available, then the characters '00000000' are returned.
STR appnLsPortName	1.3.6.1.2.1.34.4.1.1.5.1.1.4	DisplayString	read-only	Administratively assigned name for the port associated with this link station. The name can be from one to ten characters.
ADR appnLsRemoteAddr	1.3.6.1.2.1.34.4.1.1.5.1.1.42	DisplayableDlcAddress	read-only	Address of the remote link station on this link.
STR appnLsRemoteLsName	1.3.6.1.2.1.34.4.1.1.5.1.1.43	DisplayString	read-only	Remote link station discovered from the XID exchange. The name can be from one to ten characters. A zero-length string indicates that the value is not known.
OCT appnLsRevAnrLabel	1.3.6.1.2.1.34.4.1.1.5.1.1.37	OCTET STRING	read-only	The reverse Automatic Network Routing (ANR) label for this link station. If the link does not support HPR or the value is unknown, a zero-length string is returned.
OCT appnLsRouteNceId	1.3.6.1.2.1.34.4.1.1.5.1.1.39	OCTET STRING	read-only	The network connection endpoint identifier (NCE ID) for Route Setup if this node supports the HPR transport tower, a zero- length string if the value is unknown or not meaningful for this node.
NUM appnLsSpecific	1.3.6.1.2.1.34.4.1.1.5.1.1.31	RowPointer	read-only	Identifies the object, e.g., one in a DLC-specific MIB, that can provide additional information related to this link station. If the agent is unable to identify such an object, the value 0.0 is returned.
STR appnLsStatusCpName	1.3.6.1.2.1.34.4.1.1.5.2.1.4	DisplayString	read-only	Fully qualified name of the adjacent node for this link station. An adjacent node is identified using the format specified in the SnaControlPointName textual convention. The value of this object is determined as follows: 1. If the adjacent node's name was received on XID, it is returned. 2. If the adjacent node's name was not received on XID, but a locally-defined value is available, it is returned. 3. Otherwise a string of length 0 is returned, indicating that no name is known for the adjacent node.
IAN appnLsStatusDlcType	1.3.6.1.2.1.34.4.1.1.5.2.1.14	IANAifType	read-only	The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
SNA appnLsStatusEndSense	1.3.6.1.2.1.34.4.1.1.5.2.1.9	SnaSenseData	read-only	The sense data associated with the termination of the link connection to adjacent node. This is the sense data that came from the DLC layer.
appnLsStatusEntry	1.3.6.1.2.1.34.4.1.1.5.2.1		not-accessible	This table is indexed by the LsStatusIndex, which is an integer that is continuously updated until it eventually wraps.
SNA appnLsStatusGeneralSense	1.3.6.1.2.1.34.4.1.1.5.2.1.7	SnaSenseData	read-only	The error sense data associated with the start sequence of activation of a link up to the beginning of the XID sequence. This is the sense data that came from Configuration Services whenever the link did not activate or when it went inactive.
INT appnLsStatusIndex	1.3.6.1.2.1.34.4.1.1.5.2.1.1	INTEGER	not-accessible	Table index. The value of the index begins at zero and is incremented up to a maximum value of 2**31-1 (2,147,483,647) before wrapping.
ADR appnLsStatusLocalAddr	1.3.6.1.2.1.34.4.1.1.5.2.1.15	DisplayableDlcAddress	read-only	Local address of this link station.
STR appnLsStatusLsName	1.3.6.1.2.1.34.4.1.1.5.2.1.3	DisplayString	read-only	Administratively assigned name for the link station experiencing the condition.
SNA appnLsStatusPartnerId	1.3.6.1.2.1.34.4.1.1.5.2.1.5	SnaNodeIdentification	read-only	The partner's Node Identification, from bytes 2-5 of the XID received from the partner. If this value is not available, then the characters '00000000' are returned.
ADR appnLsStatusRemoteAddr	1.3.6.1.2.1.34.4.1.1.5.2.1.16	DisplayableDlcAddress	read-only	Address of the remote link station on this link.
T/F appnLsStatusRetry	1.3.6.1.2.1.34.4.1.1.5.2.1.8	TruthValue	read-only	Indicates whether the node will retry the start request to activate the link.
appnLsStatusTable	1.3.6.1.2.1.34.4.1.1.5.2		not-accessible	This table contains information related to exceptional and potentially exceptional conditions that occurred during the activation, XID exchange, and termination of a connection. No entries are created when these activities proceed normally. It is an implementation option when entries are removed from this table.
INT appnLsStatusTgNum	1.3.6.1.2.1.34.4.1.1.5.2.1.6	INTEGER	read-only	Number associated with the TG to this link station, with a range from 0 to 256. A value of 256 indicates that the TG number was unknown at the time of the failure.
DAT appnLsStatusTime	1.3.6.1.2.1.34.4.1.1.5.2.1.2	DateAndTime	read-only	Time when the exception condition occurred. This time can be used to identify when this event occurred in relation to other events in the APPN node, for example, the time at which an APPC session was either terminated or failed to be established. This latter time is available in the appcHistSessTime object in the APPC MIB.
INT appnLsStatusXidBitInError	1.3.6.1.2.1.34.4.1.1.5.2.1.13	INTEGER	read-only	This object identifies the actual bit in error (0 through 7) within the errored byte of the XID. The value 8 indicates that this object has no meaning. For values in the range 0-7, this object corresponds to byte 4 of the XID Negotiation (X'22') control vector.
INT appnLsStatusXidByteInError	1.3.6.1.2.1.34.4.1.1.5.2.1.12	INTEGER	read-only	This object identifies the actual byte in the XID that caused the error. The value 65536 indicates that the object has no meaning. For values in the range 0-65535, this object corresponds to bytes 2-3 of the XID Negotiation (X'22') control vector.
SNA appnLsStatusXidLocalSense	1.3.6.1.2.1.34.4.1.1.5.2.1.10	SnaSenseData	read-only	The sense data associated with the rejection of the XID. This is the sense data that came from the local node (this node) when it built the XID Negotiation Error control vector (cv22) to send to the remote node.
SNA appnLsStatusXidRemoteSense	1.3.6.1.2.1.34.4.1.1.5.2.1.11	SnaSenseData	read-only	The sense data the adjacent node returned to this node indicating the reason the XID was rejected. This is the sense data that came from the remote node in the XID Negotiation Error control vector (cv22) it sent to the local node (this node).
appnLsTable	1.3.6.1.2.1.34.4.1.1.5.1		not-accessible	This table contains detailed information about the link station configuration and its current status.
INT appnLsTgNum	1.3.6.1.2.1.34.4.1.1.5.1.1.9	INTEGER	read-only	Number associated with the TG to this link station, with a range from 0 to 256. A value of 256 indicates that the TG number has not been negotiated and is unknown at this time.
appnMIB	1.3.6.1.2.1.34.4			This is the MIB module for objects used to manage network devices with APPN capabilities.
appnNn	1.3.6.1.2.1.34.4.1.2
T/F appnNnNodeFRBranchAwareness	1.3.6.1.2.1.34.4.1.2.2.3.1.18	TruthValue	read-only	Indicates whether this node supports branch awareness. This object corresponds to cv4580, byte 8, bit 4.
T/F appnNnNodeFRCentralDirectory	1.3.6.1.2.1.34.4.1.2.2.3.1.11	TruthValue	read-only	Indicates whether the node supports central directory services. This object corresponds to cv4580, byte 8, bit 1.
T/F appnNnNodeFRCongested	1.3.6.1.2.1.34.4.1.2.2.3.1.7	TruthValue	read-only	Indicates whether this node is congested. This node is not be included in route selection by other nodes when this congestion exists. This object corresponds to cv4580, byte 7, bit 0.
APP appnNnNodeFREntryTimeLeft	1.3.6.1.2.1.34.4.1.2.2.3.1.3	AppnTopologyEntryTimeLeft	read-only	Number of days before deletion of this network node entry.
T/F appnNnNodeFRExteBorderSup	1.3.6.1.2.1.34.4.1.2.2.3.1.17	TruthValue	read-only	Indicates whether this node has extended border node support. This object corresponds to cv4580, byte 9, bit 2.
U32 appnNnNodeFRFrsn	1.3.6.1.2.1.34.4.1.2.2.3.1.1	Unsigned32	not-accessible	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last relative time this resource was updated at the agent node.
T/F appnNnNodeFRGarbageCollect	1.3.6.1.2.1.34.4.1.2.2.3.1.13	TruthValue	read-only	Indicates whether the node has been marked for garbage collection (deletion from the topology database) upon the next garbage collection cycle. This object corresponds to cv4580, byte 7, bit 3.
T/F appnNnNodeFRGateway	1.3.6.1.2.1.34.4.1.2.2.3.1.10	TruthValue	read-only	Indicates whether the node provide gateway services. This object corresponds to cv4580, byte 8, bit 0.
INT appnNnNodeFRHprSupport	1.3.6.1.2.1.34.4.1.2.2.3.1.14	INTEGER	read-only	Indicates the node's level of support for high-performance routing (HPR): noHprSupport(1) - no HPR support hprBaseOnly(2) - HPR base (option set 1400) supported rtpTower(3) - HPR base and RTP tower (option set 1401) supported controlFlowsOverRtpTower(4) - HPR base, RTP tower, and control flows over RTP (option set 1402) supported This object corresponds to cv4580, byte 9, bits 3-4.
T/F appnNnNodeFRInterchangeSup	1.3.6.1.2.1.34.4.1.2.2.3.1.16	TruthValue	read-only	Indicates whether this node has interchange node support. This object corresponds to cv4580, byte 9, bit 1.
T/F appnNnNodeFRIsr	1.3.6.1.2.1.34.4.1.2.2.3.1.12	TruthValue	read-only	Indicates whether the node supports intermediate session routing (ISR). This object corresponds to cv4580, byte 8, bit 2.
T/F appnNnNodeFRIsrDepleted	1.3.6.1.2.1.34.4.1.2.2.3.1.8	TruthValue	read-only	Indicates whether intermediate session routing resources are depleted. This node is not included in intermediate route selection by other nodes when resources are depleted. This object corresponds to cv4580, byte 7, bit 1.
NUM appnNnNodeFRName	1.3.6.1.2.1.34.4.1.2.2.3.1.2	SnaControlPointName	not-accessible	Administratively assigned network name that is locally defined at each network node.
T/F appnNnNodeFRPeriBorderSup	1.3.6.1.2.1.34.4.1.2.2.3.1.15	TruthValue	read-only	Indicates whether this node has peripheral border node support. This object corresponds to cv4580, byte 9, bit 0.
T/F appnNnNodeFRQuiescing	1.3.6.1.2.1.34.4.1.2.2.3.1.9	TruthValue	read-only	Indicates whether the node is quiescing. This node is not included in route selection by other nodes when the node is quiescing. This object corresponds to cv4580, byte 7, bit 5.
INT appnNnNodeFRRouteAddResist	1.3.6.1.2.1.34.4.1.2.2.3.1.6	INTEGER	read-only	Route addition resistance. This administratively assigned value indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing. This object corresponds to cv4580, byte 6.
U32 appnNnNodeFRRsn	1.3.6.1.2.1.34.4.1.2.2.3.1.5	Unsigned32	read-only	Resource sequence number, which is assigned and controlled by the network node that owns this resource. An odd number indicates that information about the resource is inconsistent. This object corresponds to the numeric value in cv4580, bytes 2-5.
INT appnNnNodeFRType	1.3.6.1.2.1.34.4.1.2.2.3.1.4	INTEGER	read-only	Type of APPN node.
T/F appnNnTgFRBranchTg	1.3.6.1.2.1.34.4.1.2.2.4.1.27	TruthValue	read-only	Indicates whether the transmission group is a branch TG (equivalently, whether the destination of the transmission group is a branch network node). This object corresponds to cv4680, byte m+1, bit 1.
INT appnNnTgFRByteCost	1.3.6.1.2.1.34.4.1.2.2.4.1.14	INTEGER	read-only	Cost per byte transmitted. This is an administratively assigned value representing the relative cost of transmitting a byte over this TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This object corresponds to cv47, byte 14.
INT appnNnTgFRConnCost	1.3.6.1.2.1.34.4.1.2.2.4.1.13	INTEGER	read-only	Cost per connect time. This is an administratively assigned value representing the relative cost per unit of time to use this TG. Range is from 0, which means no cost, to 255, which indicates maximum cost. This object corresponds to cv47, byte 13.
INT appnNnTgFRCpCpSession	1.3.6.1.2.1.34.4.1.2.2.4.1.11	INTEGER	read-only	Indicates whether CP-CP sessions are supported on this TG, and whether the TG owner's contention-winner session is active on this TG. Some nodes in the network are not able to differentiate support and status of CP-CP sessions, and thus may report the 'supportedUnknownStatus' value. This object corresponds to cv47, byte 6, bits 3-4.
APP appnNnTgFRDelay	1.3.6.1.2.1.34.4.1.2.2.4.1.16	AppnTgDelay	read-only	Administratively assigned delay associated with this TG. This object corresponds to cv47, byte 17.
NUM appnNnTgFRDest	1.3.6.1.2.1.34.4.1.2.2.4.1.3	SnaControlPointName	not-accessible	Administratively assigned fully qualified network name for the destination node for this TG.
T/F appnNnTgFRDestHprTrans	1.3.6.1.2.1.34.4.1.2.2.4.1.23	TruthValue	read-only	Indicates whether the destination node supports high performance routing (HPR) transport tower. This object corresponds to cv4680, byte m+1, bit 7.
T/F appnNnTgFRDestVirtual	1.3.6.1.2.1.34.4.1.2.2.4.1.6	TruthValue	read-only	Indicates whether the destination node is a virtual routing node.
APP appnNnTgFRDlcData	1.3.6.1.2.1.34.4.1.2.2.4.1.7	AppnTgDlcData	read-only	DLC-specific data related to a link connection network.
APP appnNnTgFREffCap	1.3.6.1.2.1.34.4.1.2.2.4.1.12	AppnTgEffectiveCapacity	read-only	Effective capacity for this TG.
APP appnNnTgFREntryTimeLeft	1.3.6.1.2.1.34.4.1.2.2.4.1.5	AppnTopologyEntryTimeLeft	read-only	Number of days before deletion of this network node TG entry if it is not operational or has an odd (inconsistent) RSN.
U32 appnNnTgFRFrsn	1.3.6.1.2.1.34.4.1.2.2.4.1.1	Unsigned32	not-accessible	Flow reduction sequence numbers (FRSNs) are associated with Topology Database Updates (TDUs) and are unique only within each APPN network node. A TDU can be associated with multiple APPN resources. This FRSN indicates the last time this resource was updated at this node.
T/F appnNnTgFRGarbageCollect	1.3.6.1.2.1.34.4.1.2.2.4.1.20	TruthValue	read-only	Indicates whether the TG has been marked for garbage collection (deletion from the topology database) upon the next garbage collection cycle. This object corresponds to cv47, byte 6, bit 1.
T/F appnNnTgFRHprSup	1.3.6.1.2.1.34.4.1.2.2.4.1.22	TruthValue	read-only	Indicates whether high performance routing (HPR) is supported over this TG. This object corresponds to cv4680, byte m+1, bit 2.
T/F appnNnTgFRIntersubnet	1.3.6.1.2.1.34.4.1.2.2.4.1.25	TruthValue	read-only	Indicates whether the transmission group is an intersubnet TG, which defines a border between subnetworks. This object corresponds to cv4680, byte m+1, bit 5.
T/F appnNnTgFRMltgLinkType	1.3.6.1.2.1.34.4.1.2.2.4.1.26	TruthValue	read-only	This object indicates whether the transmission group is a multi-link TG. A TG that has been brought up as a multi-link TG is reported as one, even if it currently has only one link active. This object corresponds to cv47, byte 6, bit 5.
INT appnNnTgFRNum	1.3.6.1.2.1.34.4.1.2.2.4.1.4	INTEGER	not-accessible	Number associated with this transmission group. Range is 0-255.
T/F appnNnTgFROperational	1.3.6.1.2.1.34.4.1.2.2.4.1.9	TruthValue	read-only	Indicates whether the transmission group is operational. This object corresponds to cv47, byte 6, bit 0.
NUM appnNnTgFROwner	1.3.6.1.2.1.34.4.1.2.2.4.1.2	SnaControlPointName	not-accessible	Administratively assigned name for the originating node for this TG. This is the same name specified in the node table.
T/F appnNnTgFRQuiescing	1.3.6.1.2.1.34.4.1.2.2.4.1.10	TruthValue	read-only	Indicates whether the transmission group is quiescing. If the TG owner is either an extended border node or a branch-aware network node (indicated, respectively, by the appnNnNodeFRExteBorderSup and appnNnNodeFRBranchAwareness objects in the corresponding appnNnTopologyFREntry), then this indicator is artificially set to TRUE in the APPN topology database, to remove the TG from other nodes' route calculations. A management application can determine whether the TG is actually quiescing by examining its appnLocalTgQuiescing object at the TG owner. This object corresponds to cv47, byte 6, bit 2.
U32 appnNnTgFRRsn	1.3.6.1.2.1.34.4.1.2.2.4.1.8	Unsigned32	read-only	Current owning node's resource sequence number for this resource. An odd number indicates that information about the resource is inconsistent. This object corresponds to the numeric value in cv47, bytes 2-5
APP appnNnTgFRSecurity	1.3.6.1.2.1.34.4.1.2.2.4.1.15	AppnTgSecurity	read-only	Administratively assigned security level of this TG. This object corresponds to cv47, byte 16.
U32 appnNnTgFRSubareaNum	1.3.6.1.2.1.34.4.1.2.2.4.1.21	Unsigned32	read-only	The subarea number associated with this TG. This object corresponds to cv4680, bytes m+2 through m+5.
INT appnNnTgFRTypeIndicator	1.3.6.1.2.1.34.4.1.2.2.4.1.24	INTEGER	read-only	Indicates the type of the TG. This object corresponds to cv4680, byte m+1, bits 3-4.
INT appnNnTgFRUsr1	1.3.6.1.2.1.34.4.1.2.2.4.1.17	INTEGER	read-only	First user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG. This object corresponds to cv47, byte 19.
INT appnNnTgFRUsr2	1.3.6.1.2.1.34.4.1.2.2.4.1.18	INTEGER	read-only	Second user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG. This object corresponds to cv47, byte 20.
INT appnNnTgFRUsr3	1.3.6.1.2.1.34.4.1.2.2.4.1.19	INTEGER	read-only	Third user-defined TG characteristic for this TG. This is an administratively assigned value associated with the TG. This object corresponds to cv47, byte 21.
appnNnTgTopologyFREntry	1.3.6.1.2.1.34.4.1.2.2.4.1		not-accessible	This table is indexed by four columns: FRSN, TG owner fully qualified node name, TG destination fully qualified node name, and TG number.
appnNnTgTopologyFRTable	1.3.6.1.2.1.34.4.1.2.2.4		not-accessible	Portion of the APPN topology database that describes all of the APPN transmissions groups between nodes in the database.
appnNnTopo	1.3.6.1.2.1.34.4.1.2.1
appnNnTopoConfGroup	1.3.6.1.2.1.34.4.3.2.9			The appnNnTopoConfGroup is mandatory only for network nodes. This RFC 2155-level group was deprecated when the appnNnNodeFRBranchAwareness, appnNnTgFRMltgLinkType, and appnNnFRBranchTg objects were added.
appnNnTopoConfGroup2	1.3.6.1.2.1.34.4.3.2.30			The appnNnTopoConfGroup is mandatory only for network nodes.
G32 appnNnTopoCurNumNodes	1.3.6.1.2.1.34.4.1.2.1.2	Gauge32	read-only	Current number of node entries in this node's topology database. It is an implementation choice whether to count only network-node entries, or to count all node entries, but an implementation must make the same choice here that it makes for the appnNnTopoMaxNodes object. If this value exceeds the maximum number of nodes allowed (appnNnTopoMaxNodes, if that field in not 0), APPN Alert CPDB002 is issued.
appnNnTopology	1.3.6.1.2.1.34.4.1.2.2
appnNnTopologyFREntry	1.3.6.1.2.1.34.4.1.2.2.3.1		not-accessible	The FRSN and the fully qualified node name are used to index this table.
appnNnTopologyFRTable	1.3.6.1.2.1.34.4.1.2.2.3		not-accessible	Portion of the APPN topology database that describes all of the APPN network nodes and virtual routing nodes known to this node.
G32 appnNnTopoMaxNodes	1.3.6.1.2.1.34.4.1.2.1.1	Gauge32	read-only	Maximum number of node entries allowed in the APPN topology database. It is an implementation choice whether to count only network-node entries, or to count all node entries. If the number of node entries exceeds this value, APPN will issue an Alert and the node can no longer participate as a network node. The value 0 indicates that the local node has no defined limit, and the number of node entries is bounded only by memory.
NUM appnNnTopoNodePurges	1.3.6.1.2.1.34.4.1.2.1.3	AppnNodeCounter	read-only	Total number of topology node records purged from this node's topology database since the node was last reinitialized.
NUM appnNnTopoTgPurges	1.3.6.1.2.1.34.4.1.2.1.4	AppnNodeCounter	read-only	Total number of topology TG records purged from this node's topology database since the node was last reinitialized.
NUM appnNnTopoTotalTduWars	1.3.6.1.2.1.34.4.1.2.1.5	AppnNodeCounter	read-only	Number of TDU wars detected by this node since its last initialization.
appnNnUniqueConfGroup	1.3.6.1.2.1.34.4.3.2.6			A collection of objects providing instrumentation unique to APPN network nodes.
appnNnUniqueInfoAndCaps	1.3.6.1.2.1.34.4.1.1.2
appnNode	1.3.6.1.2.1.34.4.1.1
T/F appnNodeAdaptiveBindPacing	1.3.6.1.2.1.34.4.1.1.1.7	TruthValue	read-only	Indicates whether this node supports adaptive bind pacing for dependent LUs.
T/F appnNodeBrNn	1.3.6.1.2.1.34.4.1.1.1.18	TruthValue	read-only	Indicates whether this node is currently configured as a branch network node. Note: throughout the remainder of this MIB module, branch network node is treated as a third node type, parallel to network node and end node. This is not how branch network nodes are treated in the base APPN architecture, but it increases clarity to do it here.
TIM appnNodeCounterDisconTime	1.3.6.1.2.1.34.4.1.1.1.16	TimeStamp	read-only	The value of the sysUpTime object the last time the APPN node was reinitialized.
NUM appnNodeCpName	1.3.6.1.2.1.34.4.1.1.1.1	SnaControlPointName	read-only	Administratively assigned network name for this node.
T/F appnNodeEnLuSearch	1.3.6.1.2.1.34.4.1.1.3.3	TruthValue	read-only	Indicates whether the node is to be searched for LUs as part of a network broadcast search. A branch network node shall also implement this object.
T/F appnNodeEnModeCosMap	1.3.6.1.2.1.34.4.1.1.3.1	TruthValue	read-only	Indicates whether this end node supports mode name to COS name mapping.
OCT appnNodeEnNnServer	1.3.6.1.2.1.34.4.1.1.3.2	OCTET STRING	read-only	The fully qualified name of the current NN server for this end node. An NN server is identified using the format specified in the SnaControlPointName textual convention. The value is a zero-length string when there is no active NN server. A branch network node shall also implement this object.
NUM appnNodeHprEndRteRejects	1.3.6.1.2.1.34.4.1.1.1.15	AppnNodeCounter	read-only	The number of HPR route setups rejected by this node for routes ending in it since the node was last reinitialized.
NUM appnNodeHprEndRteSetups	1.3.6.1.2.1.34.4.1.1.1.14	AppnNodeCounter	read-only	The total number of HPR route setups received for routes ending in this node since the node was last reinitialized.
NUM appnNodeHprIntRteRejects	1.3.6.1.2.1.34.4.1.1.1.11	AppnNodeCounter	read-only	The number of HPR route setups rejected by this node for routes passing through it since the node was last reinitialized.
NUM appnNodeHprIntRteSetups	1.3.6.1.2.1.34.4.1.1.1.10	AppnNodeCounter	read-only	The total number of HPR route setups received for routes passing through this node since the node was last reinitialized.
NUM appnNodeHprOrgRteRejects	1.3.6.1.2.1.34.4.1.1.1.13	AppnNodeCounter	read-only	The number of HPR route setups rejected by other nodes for routes originating in this node since the node was last reinitialized.
NUM appnNodeHprOrgRteSetups	1.3.6.1.2.1.34.4.1.1.1.12	AppnNodeCounter	read-only	The total number of HPR route setups sent for routes originating in this node since the node was last reinitialized.
INT appnNodeHprSupport	1.3.6.1.2.1.34.4.1.1.1.8	INTEGER	read-only	Indicates this node's level of support for high-performance routing (HPR): noHprSupport(1) - no HPR support hprBaseOnly(2) - HPR base (option set 1400) supported rtpTower(3) - HPR base and RTP tower (option set 1401) supported controlFlowsOverRtpTower(4) - HPR base, RTP tower, and control flows over RTP (option set 1402) supported This object corresponds to cv4580, byte 9, bits 3-4.
SNA appnNodeId	1.3.6.1.2.1.34.4.1.1.1.3	SnaNodeIdentification	read-only	This node's Node Identification, which it sends in bytes 2-5 of XID.
INT appnNodeLsCounterType	1.3.6.1.2.1.34.4.1.1.1.17	INTEGER	read-only	Indicates which ANR traffic, if any, the node includes in the counts returned by the APPN link station counters appnLsInXidBytes, appnLsInMsgBytes, appnLsInXidFrames, appnLsInMsgFrames, appnLsOutXidBytes, appnLsOutMsgBytes, appnLsOutXidFrames, and appnLsOutMsgFrames. These counters are always incremented for ISR traffic. The following values are defined: other(1) - the node does something different from all the options listed below noAnr(2) - the node does not include any ANR traffic in these counts anrForLocalNces(3) - the node includes in these counts ANR traffic for RTP connections that terminate in this node, but not ANR traffic for RTP connections that pass through this node without terminating in it allAnr(4) - the node includes all ANR traffic in these counts.
G32 appnNodeMaxSessPerRtpConn	1.3.6.1.2.1.34.4.1.1.1.9	Gauge32	read-only	This object represents a configuration parameter indicating the maximum number of sessions that the APPN node is to put on any HPR connection. The value is zero if not applicable.
STR appnNodeMibVersion	1.3.6.1.2.1.34.4.1.1.1.2	DisplayString	read-only	The value of LAST-UPDATED from this module's MODULE-IDENTITY macro. This object gives a Management Station an easy way of determining the level of the MIB supported by an agent. Since this object incorporates the Year 2000-unfriendly 2-digit year specified in SMI for the LAST-UPDATED field, and since it was not found to be particularly useful, it has been deprecated. No replacement object has been defined.
T/F appnNodeNnCentralDirectory	1.3.6.1.2.1.34.4.1.1.2.1	TruthValue	read-only	Indicates whether this node supports central directory services. This object corresponds to cv4580, byte 8, bit 1.
T/F appnNodeNnCongested	1.3.6.1.2.1.34.4.1.1.2.11	TruthValue	read-only	Indicates whether this node is congested. Other network nodes stop routing traffic to this node while this flag is on. This object corresponds to cv4580, byte 7, bit 0.
T/F appnNodeNnExteBorderSup	1.3.6.1.2.1.34.4.1.1.2.8	TruthValue	read-only	Indicates whether this node has extended border node support. This object corresponds to cv4580, byte 9, bit 2.
U32 appnNodeNnFrsn	1.3.6.1.2.1.34.4.1.1.2.5	Unsigned32	read-only	The last flow-reduction sequence number (FRSN) sent by this node in a topology update to an adjacent network node.
T/F appnNodeNnGateway	1.3.6.1.2.1.34.4.1.1.2.14	TruthValue	read-only	Indicates whether the node has gateway services support. This object corresponds to cv4580, byte 8, bit 0.
T/F appnNodeNnInterchangeSup	1.3.6.1.2.1.34.4.1.1.2.7	TruthValue	read-only	Indicates whether this node has interchange node support. This object corresponds to cv4580, byte 9, bit 1.
T/F appnNodeNnIsr	1.3.6.1.2.1.34.4.1.1.2.4	TruthValue	read-only	Indicates whether the node supports intermediate session routing. This object corresponds to cv4580, byte 8, bit 2.
T/F appnNodeNnIsrDepleted	1.3.6.1.2.1.34.4.1.1.2.12	TruthValue	read-only	Indicate whether intermediated session routing resources are depleted. Other network nodes stop routing traffic through this node while this flag is on. This object corresponds to cv4580, byte 7, bit 1.
T/F appnNodeNnPeriBorderSup	1.3.6.1.2.1.34.4.1.1.2.6	TruthValue	read-only	Indicates whether this node has peripheral border node support. This object corresponds to cv4580, byte 9, bit 0.
T/F appnNodeNnQuiescing	1.3.6.1.2.1.34.4.1.1.2.13	TruthValue	read-only	Indicates whether the node is quiescing. This object corresponds to cv4580, byte 7, bit 5.
INT appnNodeNnRouteAddResist	1.3.6.1.2.1.34.4.1.1.2.3	INTEGER	read-only	Route addition resistance. This administratively assigned value indicates the relative desirability of using this node for intermediate session traffic. The value, which can be any integer 0-255, is used in route computation. The lower the value, the more desirable the node is for intermediate routing. This object corresponds to cv4580, byte 6.
U32 appnNodeNnRsn	1.3.6.1.2.1.34.4.1.1.2.10	Unsigned32	read-only	Resource sequence number for this node, which it assigns and controls. This object corresponds to the numeric value in cv4580, bytes 2-5.
INT appnNodeNnSafeStoreFreq	1.3.6.1.2.1.34.4.1.1.2.9	INTEGER	read-write	The topology safe store frequency. If this number is not zero, then the topology database is saved each time the total number of topology database updates (TDUs) received by this node increases by this number. A value of zero indicates that the topology database is not being saved.
INT appnNodeNnTreeCache	1.3.6.1.2.1.34.4.1.1.2.2	INTEGER	read-only	Indicates this node's level of support for caching of route trees. Three levels are specified: noCache(1) - caching of route trees is not supported cacheNoIncrUpdate(2) - caching of route trees is supported, but without incremental updates cacheWithIncrUpdate(3) - caching of route trees with incremental updates is supported
T/F appnNodeParallelTg	1.3.6.1.2.1.34.4.1.1.1.6	TruthValue	read-only	Indicates whether this node supports parallel TGs.
INT appnNodeType	1.3.6.1.2.1.34.4.1.1.1.4	INTEGER	read-only	Type of APPN node: networkNode(1) - APPN network node endNode(2) - APPN end node t21len(4) - LEN end node Note: A branch network node SHALL return endNode(2) as the value of this object. A management application can distinguish between a branch network node and an actual end node by retrieving the appnNodeBrNn object.
TIK appnNodeUpTime	1.3.6.1.2.1.34.4.1.1.1.5	TimeTicks	read-only	Amount of time (in hundredths of a second) since the APPN node was last reinitialized.
appnObjects	1.3.6.1.2.1.34.4.1
INT appnPortCommand	1.3.6.1.2.1.34.4.1.1.4.1.1.2	INTEGER	read-write	Object by which a Management Station can activate, deactivate, or recycle (i.e., cause to be deactivated and then immediately activated) a port, by setting the value to activate(1), deactivate(2), or recycle(3), respectively. The value ready(4) is returned on GET operations until a SET has been processed; after that the value received on the most recent SET is returned.
appnPortConfGroup	1.3.6.1.2.1.34.4.3.2.2			A collection of objects providing the instrumentation of APPN port information.
TIM appnPortCounterDisconTime	1.3.6.1.2.1.34.4.1.1.4.1.1.18	TimeStamp	read-only	The value of the sysUpTime object the last time the port was started.
NUM appnPortDefLsBadXids	1.3.6.1.2.1.34.4.1.1.4.1.1.13	AppnPortCounter	read-only	The total number of unsuccessful XID exchanges that have occurred on all defined link stations on this port since the last time this port was started.
NUM appnPortDefLsGoodXids	1.3.6.1.2.1.34.4.1.1.4.1.1.12	AppnPortCounter	read-only	The total number of successful XID exchanges that have occurred on all defined link stations on this port since the last time this port was started.
ADR appnPortDlcLocalAddr	1.3.6.1.2.1.34.4.1.1.4.1.1.17	DisplayableDlcAddress	read-only	Local DLC address of this port.
IAN appnPortDlcType	1.3.6.1.2.1.34.4.1.1.4.1.1.4	IANAifType	read-only	The type of DLC interface, distinguished according to the protocol immediately 'below' this layer.
T/F appnPortDynamicLinkSupport	1.3.6.1.2.1.34.4.1.1.4.1.1.9	TruthValue	read-only	Indicates whether this node allows call-in on this port from nodes not defined locally.
NUM appnPortDynLsBadXids	1.3.6.1.2.1.34.4.1.1.4.1.1.15	AppnPortCounter	read-only	The total number of unsuccessful XID exchanges that have occurred on all dynamic link stations on this port since the last time this port was started.
NUM appnPortDynLsGoodXids	1.3.6.1.2.1.34.4.1.1.4.1.1.14	AppnPortCounter	read-only	The total number of successful XID exchanges that have occurred on all dynamic link stations on this port since the last time this port was started.
appnPortEntry	1.3.6.1.2.1.34.4.1.1.4.1.1		not-accessible	The port name is used as the index to this table.
appnPortInformation	1.3.6.1.2.1.34.4.1.1.4
INT appnPortLsRole	1.3.6.1.2.1.34.4.1.1.4.1.1.7	INTEGER	read-only	Initial role for link stations activated through this port. The values map to the following settings in the initial XID, where 'ABM' indicates asynchronous balanced mode and 'NRM' indicated normal response mode: primary(1): ABM support = 0 ( = NRM) role = 01 ( = primary) secondary(2): ABM support = 0 ( = NRM) role = 00 ( = secondary) negotiable(3): ABM support = 0 ( = NRM) role = 11 ( = negotiable) abm(4): ABM support = 1 ( = ABM) role = 11 ( = negotiable)
G32 appnPortMaxIframeWindow	1.3.6.1.2.1.34.4.1.1.4.1.1.11	Gauge32	read-only	Maximum number of I-frames that can be received by the XID sender before an acknowledgement is received.
INT appnPortMaxRcvBtuSize	1.3.6.1.2.1.34.4.1.1.4.1.1.10	INTEGER	read-only	Maximum Basic Transmission Unit (BTU) size that a link station on this port can receive. This object corresponds to bytes 21-22 of XID3.
STR appnPortName	1.3.6.1.2.1.34.4.1.1.4.1.1.1	DisplayString	not-accessible	Administratively assigned name for this APPN port.
T/F appnPortNegotLs	1.3.6.1.2.1.34.4.1.1.4.1.1.8	TruthValue	read-only	Indicates whether the node supports negotiable link stations for this port.
INT appnPortOperState	1.3.6.1.2.1.34.4.1.1.4.1.1.3	INTEGER	read-only	Indicates the current state of this port: inactive(1) - port is inactive pendactive(2) - port is pending active active(3) - port is active pendinact(4) - port is pending inactive
INT appnPortPortType	1.3.6.1.2.1.34.4.1.1.4.1.1.5	INTEGER	read-only	Identifies the type of line used by this port: leased(1) - leased line switched(2) - switched line sharedAccessFacilities(3) - shared access facility, such as a LAN.
T/F appnPortSIMRIM	1.3.6.1.2.1.34.4.1.1.4.1.1.6	TruthValue	read-only	Indicates whether Set Initialization Mode (SIM) and Receive Initialization Mode (RIM) are supported for this port.
NUM appnPortSpecific	1.3.6.1.2.1.34.4.1.1.4.1.1.16	RowPointer	read-only	Identifies the object, e.g., one in a DLC-specific MIB, that can provide additional information related to this port. If the agent is unable to identify such an object, the value 0.0 is returned.
appnPortTable	1.3.6.1.2.1.34.4.1.1.4.1		not-accessible	The Port table describes the configuration and current status of the ports used by APPN. When it is known to the APPN component, an OBJECT IDENTIFIER pointing to additional information related to the port is included. This may, but need not, be a RowPointer to an ifTable entry for a DLC interface immediately 'below' the port.
appnSessIntermediate	1.3.6.1.2.1.34.4.1.6
appnTrapConfGroup	1.3.6.1.2.1.34.4.3.2.18			The appnTrapConfGroup is optional for all APPN nodes. Nodes implementing this group shall also implement the appnTrapNotifGroup.
appnTrapNotifGroup	1.3.6.1.2.1.34.4.3.2.19			The appnTrapNotifGroup is optional for all APPN nodes. Nodes implementing this group shall also implement the appnTrapConfGroup.
appnTraps	1.3.6.1.2.1.34.4.2
appnVrnConfGroup	1.3.6.1.2.1.34.4.3.2.8			An object providing the instrumentation for virtual routing node support in an APPN node.
appnVrnEntry	1.3.6.1.2.1.34.4.1.1.6.1.1		not-accessible	This table is indexed by the virtual routing node name, TG number, and port name. There will be a matching entry in the appnLocalTgTable to represent status and characteristics of the TG representing each virtual routing node definition.
appnVrnInfo	1.3.6.1.2.1.34.4.1.1.6
NUM appnVrnName	1.3.6.1.2.1.34.4.1.1.6.1.1.1	SnaControlPointName	not-accessible	Administratively assigned name of the virtual routing node. This is a fully qualified name, and matches the appnLocalTgDest name in the appnLocalTgTable.
STR appnVrnPortName	1.3.6.1.2.1.34.4.1.1.6.1.1.3	DisplayString	read-only	The name of the port this virtual routing node definition is defined to.
appnVrnTable	1.3.6.1.2.1.34.4.1.1.6.1		not-accessible	This table relates a virtual routing node to an APPN port.
INT appnVrnTgNum	1.3.6.1.2.1.34.4.1.1.6.1.1.2	INTEGER	not-accessible	Number associated with the transmission group representing this virtual routing node definition.

RFC description

Manages Advanced Peer-to-Peer Networking capabilities for SNA devices, branch networks, and multi-link transmission groups.

Start monitoring SNA/APPN-capable router or network node with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download APPN-MIB

What Is APPN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description