All MIBs › ALCATEL-IND1-OSPF-MIB
Organization: Alcatel-Lucent
Last Updated: 2007-04-03
Category: Routing Protocols, Vendor: Alcatel-Lucent
Description: Alcatel OmniSwitch OSPFv2 routing protocol MIB for managing OSPF areas, interfaces, neighbors, and LSA parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ALCATEL-IND1-OSPF-MIB?
ALCATEL-IND1-OSPF-MIB is an Alcatel-Lucent OmniSwitch proprietary MIB for configuring OSPFv2 routing, and in this sample the exposed objects are specifically the OSPF debug-logging controls -- switches that turn on/off detailed diagnostic tracing for OSPF errors, warnings, state transitions, packet receive/send, flooding, SPF calculation, the link-state database, routing database, interface aging, and virtual links. Rather than exposing traffic counters, this portion of the MIB is a software-diagnostics control surface, letting operators enable targeted debug logging to troubleshoot OSPF adjacency or convergence problems as they happen. Its monitoring value is therefore indirect: it doesn't report link/CPU/memory health itself, but toggling alaOspfDebugState or alaOspfDebugSPF lets an engineer capture live OSPF protocol behavior when neighbors flap or routes fail to converge. The full OSPF MIB, of which this is the global-configuration portion, is built as an Alcatel extension layered over the standard OSPF routing model (RFC 1850 OSPF-MIB), with these objects supplementing rather than replacing the standard MIB's operational objects. It is typically used by network engineers on Alcatel/Alcatel-Lucent OmniSwitch routers/switches to debug OSPF neighbor and convergence issues in a live production network. Engineers can download the ALCATEL-IND1-OSPF-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-OSPF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Alcatel/Alcatel-Lucent OmniSwitch router/switch
Monitoring Examples
A network engineer suspecting flapping OSPF adjacencies sets alaOspfDebugState and alaOspfDebugRecv/alaOspfDebugSend to enable detailed state-transition and packet-level tracing, then reviews the resulting debug output for an unstable virtual link surfaced via alaOspfDebugVlink. Turning on alaOspfDebugSPF and alaOspfDebugLsdb would similarly help diagnose repeated SPF recalculations caused by an unstable link-state database entry.
What Can Be Monitored
- OSPF debug logging level
- OSPF error/warning logging
- OSPF state transition tracing
- OSPF packet send/receive tracing
- SPF/LSDB/RDB debug tracing
- virtual link debug tracing
This MIB depends on
Related MIBs
Imported Objects
From ALCATEL-IND1-BASE
| routingIND1Ospf | OBJECT-IDENTITY |
From OSPF-MIB
| ospfAreaAggregateEntry | |
| ospfAreaEntry | OBJECT-TYPE |
| ospfAreaId | OBJECT-TYPE |
| ospfExtLsdbEntry | |
| ospfIfEntry | |
| ospfNbrEntry | |
| ospfVirtIfEntry | |
| ospfVirtNbrEntry |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using alaOspfTotalSpfRuns OID:
Select an Alcatel-Lucent Enterprise OmniSwitch switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type alaOspfTotalSpfRuns into the Find box to locate it in the OID tree, then select it and click OK. It reports the total number of SPF runs performed on this router. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| I32 alaOspfAddressLessIf | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.37.1.2 | Integer32 | read-only | For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address. |
| C32 alaOspfArea2WayNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.10 | Counter32 | read-only | Number of ospf 2-WAY state neighbors in this area |
| C32 alaOspfAreaActiveVlinks | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.3 | Counter32 | read-only | Number of active virtual links in this area |
| alaOspfAreaAggregateAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.38.1 | not-accessible | Additions to the area aggregate table | |
| alaOspfAreaAggregateAugGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.10 | Additions to the area aggregate table. | ||
| alaOspfAreaAggregateAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.38 | not-accessible | Extensions to ospfAreaAggregateTable | |
| INT alaOspfAreaAggregateMetric | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.38.1.1 | INTEGER | read-write | If set, this value is used as the metric for the area aggregate route, overriding the calculated metric |
| OCT alaOspfAreaAttachedIntfs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.9 | OCTET STRING | read-only | List of interfaces attached to this area |
| alaOspfAreaAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1 | not-accessible | Area table additions | |
| alaOspfAreaAugGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.11 | Area table additions. | ||
| alaOspfAreaAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35 | not-accessible | Extensions to ospfAreaTable | |
| C32 alaOspfAreaExchNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.6 | Counter32 | read-only | Number of ospf EXCHANGE state neighbors in this area |
| C32 alaOspfAreaFullNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.7 | Counter32 | read-only | Number of ospf FULL state neighbors in this area |
| C32 alaOspfAreaIncrSpfRuns | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.4 | Counter32 | read-only | The number of times that incremental SPF has been run for this area to calculate inter-area routes |
| C32 alaOspfAreaInitNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.5 | Counter32 | read-only | Number of ospf INIT state neighbors in this area |
| alaOspfAreaInterfaceEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.37.1 | not-accessible | Lests all interfaces attached to a specific area | |
| alaOspfAreaInterfaceGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.7 | all interfaces attached to a specific area. | ||
| alaOspfAreaInterfaceTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.37 | not-accessible | This table holds the mapping between area ID and the interfaces attached to it | |
| C32 alaOspfAreaLastSpfRun | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.2 | Counter32 | read-only | Time in secs since last SPF ran for this area |
| IP alaOspfAreaNssaElectedTranslatorRouterId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.15 | IpAddress | read-only | The elected/current NSSA translator router id elected by this NSSA border router. For non-NSSA border router, this object is not defined. |
| INT alaOspfAreaNssaImportSetPbit | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.13 | INTEGER | read-only | Specifies whether or not an NSSA AS boundary router sets the P-bit when external routes are imported into the NSSA as Type-7 LSAs. For non-NSSA boundary routers, this value is not defined and will be none. |
| INT alaOspfAreaNssaTranslatorRole | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.11 | INTEGER | read-only | Specifies whether or not an NSSA border router will unconditionally translate Type-7 LSAs into Type-5 LSAs. When set to always, an NSSA border router always translates Type-7 LSAs into Type-5 LSAs regardless of the translator state of other NSSA border routers. When set to candidate, an NSSA border router participates in the translator election process. For non-NSSA border routers, this value is none. |
| INT alaOspfAreaNssaTranslatorStabilityInterval | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.12 | INTEGER | read-only | Defines the length of time (in seconds) an elected Type-7 translator will continue to perform its translator duties once it has determined that its translator status has been deposed by another NSSA border router translator. For non-NSSA border routers, this value is not defined and will be 0. |
| INT alaOspfAreaNssaTranslatorState | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.14 | INTEGER | read-only | The state of the NSSA Translator, for NSSA border routers. For non-NSSA border routers, the state is none. |
| C32 alaOspfAreaNumIntfs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.8 | Counter32 | read-only | Number of interfaces in this area |
| INT alaOspfAreaOperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.35.1.1 | INTEGER | read-only | Operational status of the area |
| INT alaOspfAsBdrRtr | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.9 | INTEGER | read-write | Enable or disable the switch being configured as an ASBR (Autonomous System Border Router. NOT SUPPORTED - Use IETF_OSPF.mib variable ospfASBdrRtrStatus. |
| TIK alaOspfBdrRouterAge | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.7 | TimeTicks | read-only | The number of seconds since this route was last updated or otherwise determined to be correct. |
| IP alaOspfBdrRouterAreaId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.1 | IpAddress | read-only | The area to which the border router belongs to. |
| alaOspfBdrRouterEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1 | not-accessible | OSPF routing table which contains the routes to border (ABR and ASBR) routers. | |
| alaOspfBdrRouterGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.5 | Collection of objects for management of routes to Border Routers. | ||
| IP alaOspfBdrRouterId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.2 | IpAddress | read-only | The router idenitifer of this border router. |
| INT alaOspfBdrRouterIfIndex | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.5 | INTEGER | read-only | The ifIndex value which identifies the local interface through which the next hop of this route should be reached. |
| INT alaOspfBdrRouterMetric | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.8 | INTEGER | read-only | The cost to reach the border router. |
| IP alaOspfBdrRouterNextHop | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.4 | IpAddress | read-only | The address of the next hop to reach this border router. |
| ROW alaOspfBdrRouterStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.9 | RowStatus | read-only | The row status variable, used according to row installation and removal conventions. |
| alaOspfBdrRouterTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13 | not-accessible | OSPF routing table which contains the routes to border (ABR and ASBR) routers. | |
| INT alaOspfBdrRouterTos | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.3 | INTEGER | read-only | Type Of Service (TOS) for this route. |
| INT alaOspfBdrRouterType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.13.1.6 | INTEGER | read-only | The type of border router. |
| INT alaOspfBfdAllInterfaceStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.43 | INTEGER | read-write | Enables or disables bfd for all OSPF interfaces |
| INT alaOspfBfdStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.42 | INTEGER | read-write | Enables or disables bfd for OSPF protocol |
| INT alaOspfDebugAge | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.11 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugAge MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugAll | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.25 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugAll MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugArea | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.18 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugArea MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugAuth | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.17 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugAuth MIB Object of alaDrcTmOspfDebug Configuration |
| alaOspfDebugConfig | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2 | |||
| INT alaOspfDebugDbexch | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.15 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugDbexch MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugError | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.2 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugError MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugFlood | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.7 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugFlood MIB Object of alaDrcTmOspfDebug Configuration |
| alaOspfDebugGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.3 | Collection of objects for management of Debugging configuration. | ||
| INT alaOspfDebugHello | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.16 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugHello MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugHelper | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.27 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugHelper MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugInfo | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.21 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugInfo MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugIntf | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.19 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugIntf MIB Object of alaDrcTmOspfDebug Configuration |
| I32 alaOspfDebugLevel | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.1 | Integer32 | read-write | This Object is deprecated in favour of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugLsdb | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.9 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugLsdb MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugMip | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.20 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugMip MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugRdb | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.10 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugRdb MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugRecv | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.5 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugRecv MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugRedist | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.13 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugRedist MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugRestart | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.26 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugRestart MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugSend | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.6 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugSend MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugSetup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.22 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugSetup MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugSPF | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.8 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugSPF MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugState | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.4 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugState MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugSummary | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.14 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugSummary MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugTime | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.23 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugTime MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugTm | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.24 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugTm MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugVlink | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.12 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugVlink MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDebugWarning | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.2.3 | INTEGER | read-write | This Object is deprecated in favour of alaDrcTmOspfDebugWarning MIB Object of alaDrcTmOspfDebug Configuration |
| INT alaOspfDefaultOriginate | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.39 | INTEGER | read-write | Indicates whether this ASBR router originates the default route into the OSPF normal area(s). If set to 'only', the default route is advertised into the OSPF normal area, provided the ASBR has a route to 0.0.0.0/0 in its routing table. Alternatively, if set to 'always', a default route is advertised into the OSPF domain regardless of whether the ASBR has a route to 0.0.0.0/0. A value of 'none' has the effect of not originating the default route. |
| INT alaOspfDefaultOriginateMetric | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.41 | INTEGER | read-write | Default metric to be used for the default route. |
| INT alaOspfDefaultOriginateMetricType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.40 | INTEGER | read-write | Type of metric to be used with the default route. |
| alaOspfExtLsdbAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1 | not-accessible | External Link state database additions | |
| alaOspfExtLsdbAugGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.12 | External Link state database additions. | ||
| alaOspfExtLsdbAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36 | not-accessible | Extensions to ospfExtLsdbTable | |
| IP alaOspfExtLsdbFwdAddr | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.3 | IpAddress | read-only | The address to which data traffic for the advertised destination is to be forwarded. If the Forwarding address is set to 0.0.0.0, data traffic is to be forwarded to the LSA's originator. |
| I32 alaOspfExtLsdbLength | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.6 | Integer32 | read-only | The length of the AS External Link-State Advertisement. |
| IP alaOspfExtLsdbMask | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.7 | IpAddress | read-only | The IP address mask for the advertised destination. |
| I32 alaOspfExtLsdbMetric | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.5 | Integer32 | read-only | The OSPF External TOS 0 Metric. |
| INT alaOspfExtLsdbMetricType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.4 | INTEGER | read-only | The type of external metric. |
| INT alaOspfExtLsdbProto | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.1 | INTEGER | read-only | Protocol through which this external LSA was learnt |
| C32 alaOspfExtLsdbRouteTag | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.36.1.2 | Counter32 | read-only | A 32-bit value attached to each external route. |
| alaOspfGeneralGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.9 | Collection of objects for management of Interface MD5 configuration. | ||
| alaOspfGeneralTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3 | |||
| C32 alaOspfIf2WayNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.13 | Counter32 | read-only | Number of ospf 2-WAY state neighbors on this interface |
| alaOspfIfAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1 | not-accessible | An entry of alaOspfIfAugTable | |
| alaOspfIfAugGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.13 | |||
| alaOspfIfAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17 | not-accessible | Expansion for ospfIfTable | |
| IP alaOspfIfBdrRouterid | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.5 | IpAddress | read-only | Router Id of Backup Designated router for this interface |
| INT alaOspfIfBfdDrsOnly | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.15 | INTEGER | read-create | Enables/Disables Drs Only option for a BFD interface |
| INT alaOspfIfBfdStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.14 | INTEGER | read-create | Enables/Disables OSPF for a BFD interface |
| IP alaOspfIfDrRouterid | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.4 | IpAddress | read-only | Router Id of Designated router for this interface |
| ALA alaOspfIfEncryptKey | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.1 | AlaAuthenticationEncryptKey | read-create | The authentication encryption key that is used to decypher OSPF passwords. |
| C32 alaOspfIfExchNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.8 | Counter32 | read-only | Number of ospf EXCHANGE state neighbors on this interface |
| C32 alaOspfIfFullNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.9 | Counter32 | read-only | Number of ospf FULL state neighbors on this interface |
| C32 alaOspfIfInitNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.7 | Counter32 | read-only | Number of ospf INIT state neighbors on this interface |
| STR alaOspfIfIntfName | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.12 | DisplayString | read-only | The user defined name used to identify the IP interface |
| IP alaOspfIfIpAddress | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.37.1.1 | IpAddress | read-only | The IP address of this OSPF interface. |
| IP alaOspfIfIpMask | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.2 | IpAddress | read-only | The IP mask of this OSPF interface. |
| INT alaOspfIfLinkType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.10 | INTEGER | read-only | Type of physical medium used for transmission of OSPF packets |
| ALA alaOspfIfMd5EncryptKey | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.9 | AlaAuthenticationEncryptKey | read-write | The MD5 message digest Encrypted key. |
| alaOspfIfMd5Entry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1 | not-accessible | The OSPF Interface MD5 Entry describes the MD5 key management for OSPF interfaces. | |
| alaOspfIfMd5Group | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.8 | Collection of objects for management of Interface MD5 configuration. | ||
| IP alaOspfIfMd5IpAddress | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.1 | IpAddress | read-only | The IP address of this OSPF MD5 key interface. |
| OCT alaOspfIfMd5Key | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.3 | OCTET STRING | read-write | The MD5 message digest key. |
| INT alaOspfIfMd5KeyId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.2 | INTEGER | read-only | A key identifier which identifies the algorithm and MD5 secret key associated with this interface. |
| TIK alaOspfIfMd5KeyStartAccept | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.4 | TimeTicks | read-write | The time that OSPF router will start accepting packets that have been created with this key. |
| TIK alaOspfIfMd5KeyStartGenerate | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.6 | TimeTicks | read-write | The time that OSPF router will start using this key for packet generation. |
| TIK alaOspfIfMd5KeyStopAccept | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.5 | TimeTicks | read-write | The time that OSPF router will stop accepting packets that have been created with this key. |
| TIK alaOspfIfMd5KeyStopGenerate | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.7 | TimeTicks | read-write | The time that OSPF router will stop using this key for packet generation. |
| ROW alaOspfIfMd5RowStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16.1.8 | RowStatus | read-write | Row status of this entry. |
| alaOspfIfMd5Table | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.16 | not-accessible | The OSPF Interface MD5 Table describes the MD5 key management for OSPF interfaces. | |
| C32 alaOspfIfMTU | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.6 | Counter32 | read-only | Max Transfer size of OSPF packets on this interface |
| INT alaOspfIfOperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.11 | INTEGER | read-only | Operational status of this interface |
| I32 alaOspfIfVlanId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.17.1.3 | Integer32 | read-only | Vlan Identifier associated with this interface |
| alaOspfMiscellaneousGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.1 | Collection of Miscellaneous objects for management of OSPF. | ||
| INT alaOspfMTUCheck | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.8 | INTEGER | read-write | Enable or disable the check for MTU size in database description packets. Disabled by default |
| IP alaOspfNbrAreaId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.4 | IpAddress | read-only | The area to which this neighbor belongs |
| alaOspfNbrAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1 | not-accessible | Additions to neighbor table | |
| alaOspfNbrAugEntryGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.14 | |||
| alaOspfNbrAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31 | not-accessible | Extensions to the ospfNbrTable | |
| IP alaOspfNbrBdrAddress | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.6 | IpAddress | read-only | Backup Designated router of this neighbor |
| IP alaOspfNbrDrAddress | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.5 | IpAddress | read-only | Designated router of this neighbor |
| C32 alaOspfNbrLastHello | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.10 | Counter32 | read-only | No of seconds elapsed since the last hello was received from this neighbor |
| C32 alaOspfNbrMd5SeqNo | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.9 | Counter32 | read-only | Sequence number used in Md5 authentication |
| INT alaOspfNbrMode | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.8 | INTEGER | read-only | Current neighbor mode. This is applicable only during adjacency formation |
| C32 alaOspfNbrPendingLSack | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.12 | Counter32 | read-only | Number of outstanding link state acknowledgements to be sent to this neighbor |
| C32 alaOspfNbrPendingLSreq | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.11 | Counter32 | read-only | Number of outstanding link state requests to be sent to this neighbor |
| C32 alaOspfNbrPendingLSupd | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.13 | Counter32 | read-only | Number of outstanding link state update packets to be sent to this neighbor |
| U32 alaOspfNbrRestartHelperAge | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.2 | Unsigned32 | read-only | Remaining time in current OSPF hitless restart interval, if the router is acting as a restart helper for the neighbor. |
| INT alaOspfNbrRestartHelperExitReason | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.3 | INTEGER | read-only | Describes the outcome of the last attempt at acting as a hitless restart helper for the neighbor. |
| INT alaOspfNbrRestartHelperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.1 | INTEGER | read-only | Indicates whether the router is acting as a hitless restart helper for the neighbor. |
| INT alaOspfNbrType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.31.1.7 | INTEGER | read-only | Neighbors learned via the OSPF Hello protocol are dynamic. Configured neighbors are static |
| T/F alaOspfOpaqueLsaSupport | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.23 | TruthValue | read-only | The router's support for Opaque LSA types. |
| INT alaOspfRedistAdminStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.1 | INTEGER | read-write | Enable or disable redistribution of routes into OSPF. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| alaOspfRedistProtoEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1 | not-accessible | A range of routes from a protocol to be redistributed using OSPF. This entry has been deprecated. Use the alaRouteMapRedistProtoEntry of AlcatelIND1RouteMap.mib. | |
| alaOspfRedistProtoGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.2 | Collection of objects for management of Route Redistribution Protocol. These objects have been deprecated, and the group is no longer mandatory. | ||
| INT alaOspfRedistProtoId | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1.1 | INTEGER | read-only | The routing mechanism via which the routes, to be redistributed using OSPF, are learned. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| INT alaOspfRedistProtoMetric | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1.4 | INTEGER | read-write | Default metric to be used for redistributing routes using type1 metric type. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| INT alaOspfRedistProtoMetricType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1.3 | INTEGER | read-write | Type of metric to be used for redistribution. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| C32 alaOspfRedistProtoRouteTag | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1.6 | Counter32 | read-only | Associated route tag. This object has been deprecated. |
| ROW alaOspfRedistProtoStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1.5 | RowStatus | read-write | Row status of this entry. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| INT alaOspfRedistProtoSubnets | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10.1.2 | INTEGER | read-write | Enable/disable the reditribution of subnet routes. Default value is enable. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| alaOspfRedistProtoTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.10 | not-accessible | Protocol based configuration for route redistribution using OSPF. This table has been deprecated. Use the alaRouteMapRedistProtoTable of AlcatelIND1RouteMap.mib. | |
| INT alaOspfRedistRouteControl | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.5 | INTEGER | read-write | Specifies how routes matching this entry are to be redistributed into OSPF. The different mechanisms possible are to redistribute all the subnet routes, redistribute an aggregated route if there are one or more actual routes which match this entry or redistribute only an exactly matching route. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| IP alaOspfRedistRouteDest | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.2 | IpAddress | read-only | The destination IP address of this route. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| INT alaOspfRedistRouteEffect | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.7 | INTEGER | read-write | Specifies whether the redistribution of routes in this range is allowed or denied. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| alaOspfRedistRouteEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1 | not-accessible | A configuration table which controls the routes to be redistributed by OSPF from other routing protocols. This entry has been deprecated. Use the alaRouteMapRedistProtoEntry of AlcatelIND1RouteMap.mib. | |
| alaOspfRedistRouteGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.6 | Collection of objects for management of Route Redistribution configuration. These objects have been deprecated, and the group is no longer mandatory. | ||
| IP alaOspfRedistRouteMask | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.3 | IpAddress | read-only | The network mask for this route. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| INT alaOspfRedistRouteMetric | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.4 | INTEGER | read-write | The metric to be used for the redistributed route. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| INT alaOspfRedistRouteProto | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.1 | INTEGER | read-write | Protocol from which this route is to be imported into OSPF. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| ROW alaOspfRedistRouteStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.8 | RowStatus | read-write | The row status variable, used according to row installation and removal conventions. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| alaOspfRedistRouteTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14 | not-accessible | A configuration table which controls the routes to be redistributed by OSPF from other routing protocols. This table has been deprecated. Use the alaRouteMapRedistProtoTable of AlcatelIND1RouteMap.mib. | |
| INT alaOspfRedistRouteTag | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.2 | INTEGER | read-write | A 32-bit value tagged to each OSPF internal route that is redistributed in to other routing protocol domains. The lower 16-bits typically indicate the autonomous system number. |
| INT alaOspfRedistRouteTagMatch | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.14.1.6 | INTEGER | read-write | Redistribute the route only when the route tag matches with this value. It defaults to 0 which matches all route tags. This object has been deprecated. Use the alaRouteMapRedistProtoEntry objects of AlcatelIND1RouteMap.mib. |
| U32 alaOspfReferenceBandwidth | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.25 | Unsigned32 | read-only | Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS) |
| U32 alaOspfRestartAge | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.29 | Unsigned32 | read-only | Remaining time in current OSPF hitless restart interval. |
| INT alaOspfRestartExitReason | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.30 | INTEGER | read-only | Describes the outcome of the last attempt at a hitless restart. If the value is 'none', no restart has yet been attempted. If the value is 'inProgress', a restart attempt is currently underway. |
| INT alaOspfRestartHelperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.21 | INTEGER | read-only | Indicates whether this OSPF router is operating as a Helper to a restarting router. |
| INT alaOspfRestartHelperStrictLSAChecking | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.20 | INTEGER | read-write | Indicates whether or not a changed LSA will result in termination of graceful restart by a helping router. |
| INT alaOspfRestartHelperSupport | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.19 | INTEGER | read-write | The router's support for acting as an OSPF hitless restart helper. |
| INT alaOspfRestartInitiate | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.33 | INTEGER | read-write | Initiates a planned graceful restart, if set to plannedRestart. |
| I32 alaOspfRestartInterval | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.27 | Integer32 | read-write | Configured OSPF hitless restart timeout interval. |
| INT alaOspfRestartStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.28 | INTEGER | read-only | Current status of OSPF hitless restart. The status of hitless restart is unplannedRestart after a CMM takeover. Before CMM takeover, the status is plannedRestart. |
| INT alaOspfRestartSupport | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.26 | INTEGER | read-write | The router's support for OSPF hitless restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts. |
| T/F alaOspfRFC1583Compatibility | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.22 | TruthValue | read-only | Indicates metrics used to choose among multiple AS- external-LSAs. When RFC1583Compatibility is set to enabled, only cost will be used when choosing among multiple AS-external-LSAs advertising the same destination. When RFC1583Compatibility is set to disabled, preference will be driven first by type of path using cost only to break ties. |
| TIK alaOspfRouteAge | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.7 | TimeTicks | read-only | The number of seconds since this route was last updated or otherwise determined to be correct. |
| IP alaOspfRouteDest | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.1 | IpAddress | read-only | The destination IP address of this route. |
| alaOspfRouteEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1 | not-accessible | OSPF routing table which contains the network routes. | |
| alaOspfRouteGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.4 | Collection of objects for management of Network Route configuration. | ||
| INT alaOspfRouteIfIndex | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.5 | INTEGER | read-only | The ifIndex value which identifies the local interface through which the next hop of this route should be reached. |
| IP alaOspfRouteMask | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.2 | IpAddress | read-only | The network mask for this route. |
| INT alaOspfRouteMetric1 | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.9 | INTEGER | read-only | The primary routing metric for this route. |
| INT alaOspfRouteMetric2 | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.10 | INTEGER | read-only | An alternate routing metric for this route. It's 0 for internal routes. For an external route, it's the metric to reach the ASBR that announced the external route. |
| IP alaOspfRouteNextHop | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.4 | IpAddress | read-only | The address of the next hop to reach this route. |
| C32 alaOspfRouteNumber | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.7 | Counter32 | read-only | The number of network routes in OSPF routing table. |
| ROW alaOspfRouteStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.11 | RowStatus | read-only | The row status variable, used according to row installation and removal conventions. |
| alaOspfRouteTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12 | not-accessible | OSPF routing table which contains the network routes. | |
| INT alaOspfRouteTag | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.8 | INTEGER | read-only | The associated route tag for external roues. It's 0 for routes internal to the autonomous system. |
| INT alaOspfRouteTos | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.3 | INTEGER | read-only | Type Of Service (TOS) for this route. |
| INT alaOspfRouteType | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.12.1.6 | INTEGER | read-only | The type of route. |
| INT alaOspfTimerSpfDelay | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.3 | INTEGER | read-write | Number of seconds to delay the SPF calculation after receiving a topology change. This value should not be greater than SPF hold time. |
| INT alaOspfTimerSpfHold | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.4 | INTEGER | read-write | Minimum time, in seconds, between two consecutive SPF calculations. This value should not be less than SPF delay time. |
| C32 alaOspfTotal2wayNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.10 | Counter32 | read-only | Number of 2-way state neighbors on this router |
| C32 alaOspfTotalActiveAreas | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.7 | Counter32 | read-only | Total Number of active areas configured on this router |
| C32 alaOspfTotalAreas | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.6 | Counter32 | read-only | Total Number of areas configured on this router |
| C32 alaOspfTotalExchNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.4 | Counter32 | read-only | Number of EXCHANGE state neighbors on this router |
| C32 alaOspfTotalFullNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.5 | Counter32 | read-only | Number of FULL state neighbors on this router |
| C32 alaOspfTotalIncrSpfRuns | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.2 | Counter32 | read-only | Total number of Incremental SPF runs performed on this router |
| C32 alaOspfTotalInitNbrs | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.3 | Counter32 | read-only | Number of INIT state neighbors on this router |
| C32 alaOspfTotalNSSA | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.9 | Counter32 | read-only | Total Number of NSSA areas on this router |
| C32 alaOspfTotalSpfRunsEx | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.1 | Counter32 | read-only | Total number of SPF runs performed on this router |
| C32 alaOspfTotalTransitAreas | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.3.8 | Counter32 | read-only | Number of transit areas on this router |
| T/F alaOspfTrafficEngineeringSupport | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.24 | TruthValue | read-only | The router's support for OSPF traffic engineering. |
| alaOspfVirtIfAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.18.1 | not-accessible | An entry of alaOspfVirtIfAugTable | |
| alaOspfVirtIfAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.18 | not-accessible | Expansion for ospfVirtIfTable | |
| ALA alaOspfVirtIfEncryptKey | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.18.1.1 | AlaAuthenticationEncryptKey | read-create | The authentication encryption key that is used to decypher OSPF passwords. |
| INT alaOspfVirtIfOperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.18.1.2 | INTEGER | read-only | Operational status of the virtual link |
| alaOspfVirtNbrAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1 | not-accessible | Information regarding a single virtual neighbor. | |
| alaOspfVirtNbrAugGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.16 | |||
| alaOspfVirtNbrAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32 | not-accessible | Extensions to ospfVirtNbrTable | |
| IP alaOspfVirtNbrBdrAddr | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.5 | IpAddress | read-only | Backup Designated router of this virtual neighbor |
| IP alaOspfVirtNbrDrAddr | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.4 | IpAddress | read-only | Designated router of this virtual neighbor |
| C32 alaOspfVirtNbrLastHello | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.8 | Counter32 | read-only | No of seconds elapsed since the last hello was received from this neighbor |
| C32 alaOspfVirtNbrMd5SeqNo | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.7 | Counter32 | read-only | Sequence number used in Md5 authentication |
| INT alaOspfVirtNbrMode | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.6 | INTEGER | read-only | Current neighbor mode. This is applicable only during adjacency formation |
| C32 alaOspfVirtNbrPendingLSack | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.10 | Counter32 | read-only | Number of outstanding link state acknowledgements to be sent to this neighbor |
| C32 alaOspfVirtNbrPendingLSreq | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.9 | Counter32 | read-only | Number of outstanding link state requests to be sent to this neighbor |
| C32 alaOspfVirtNbrPendingLSupd | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.11 | Counter32 | read-only | Number of outstanding link state update packets to be sent to this neighbor |
| U32 alaOspfVirtNbrRestartHelperAge | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.2 | Unsigned32 | read-only | Remaining time in current OSPF hitless restart interval, if the router is acting as a restart helper for the neighbor. |
| INT alaOspfVirtNbrRestartHelperExitReason | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.3 | INTEGER | read-only | Describes the outcome of the last attempt at acting as a hitless restart helper for the neighbor. |
| INT alaOspfVirtNbrRestartHelperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1.32.1.1 | INTEGER | read-only | Indicates whether the router is acting as a hitless restart helper for the neighbor. |
| alaProtocolOspf | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1.1 | |||
| alaProtocolOspfGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1.15 | |||
| alcatelIND1OSPFMIB | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1 | This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): For the Birds Of Prey Product Line Configuration Of Global OSPF Configuration Parameters. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2007 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE | ||
| alcatelIND1OSPFMIBCompliance | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.2.1 | Compliance statement for Open Shortest Path First (OSPF) Subsystem. | ||
| alcatelIND1OSPFMIBCompliances | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.2 | Branch For Open Shortest Path First (OSPF) Subsystem Compliance Statements. | ||
| alcatelIND1OSPFMIBConformance | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2 | Branch For Open Shortest Path First (OSPF) Subsystem Conformance Information. | ||
| alcatelIND1OSPFMIBGroups | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.2.1 | Branch For Open Shortest Path First (OSPF) Subsystem Units Of Conformance. | ||
| alcatelIND1OSPFMIBObjects | 1.3.6.1.4.1.6486.801.1.2.1.10.4.1.1 | Branch For Open Shortest Path First (OSPF) Subsystem Managed Objects. |
RFC description
Configuration of global OSPF parameters for Birds Of Prey routing.
Start monitoring Alcatel-Lucent Enterprise OmniSwitch switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.