A3COM-PRIVATE-MIB

All MIBs › A3COM-PRIVATE-MIB

Organization: 3COM Networks, Inc

Last Updated: 2004-10-12

Category: Device Management, Vendor: 3Com

Description: Defines the 3Com enterprise private MIB root OID structure and common object definitions shared across the 3Com product MIB suite.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-PRIVATE-MIB?

This is the 3Com enterprise private MIB defining the root OID structure and common object definitions shared across 3Com's broader product MIB suite, including switch and access-point product lines. It exposes a mix of hardware identification data (hardware/boot-ROM/opcode firmware version, serial number), serial console line configuration (baud rate, parity, stop bits), switch port tables, and 802.11 wireless authentication/filtering settings for 3Com access points. Its monitoring value is notable for hardware and software status: swHardwareVer, swBootRomVer, swOpCodeVer, and swSerialNumber let an operator confirm exactly which hardware revision and firmware build a device is running, essential for tracking fleet-wide firmware compliance. As a common/shared root MIB it underpins many other 3Com product-specific MIBs that import its base object identifiers. It's deployed across the general 3Com switch and wireless access point product line. Engineers can download the A3COM-PRIVATE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-PRIVATE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

3Com switches
3Com wireless access points

Monitoring Examples

An admin auditing firmware compliance across a fleet of 3Com switches/APs would poll swHardwareVer, swBootRomVer, and swOpCodeVer to confirm all units run the approved firmware, and swSerialNumber to inventory hardware. On wireless access points, walking dot11AuthenticationEntry and dot11Filter reveals the configured Wi-Fi authentication and MAC-filtering policy, while lineTable/lineEntry (lineSpeed, lineParity, lineDataBits) exposes console/serial port settings for confirming out-of-band management access.

What Can Be Monitored

hardware version
boot ROM version
firmware/opcode version
serial number
console/serial line settings
802.11 authentication and filter configuration

Imported Objects

From RFC1155-SMI

Counter
IpAddress
enterprises
mgmt

From RFC1213-MIB

ifIndex

From SNMPv2-SMI

Counter32
Integer32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
a3Com	1.3.6.1.4.1.43
MAC apNotificationDot11AuthenticatorMacAddr	1.3.6.1.4.1.43.35.8.100.1.6	MacAddress	not-accessible	This attribute holds the MAC address of the authenticator for the AP.
IP apNotificationDot11IpAddress	1.3.6.1.4.1.43.35.8.100.1.5	IpAddress	not-accessible	This value indicates the IP address of the Access Point
MAC apNotificationDot11MacAddr	1.3.6.1.4.1.43.35.8.100.1.1	MacAddress	not-accessible	Mac Address of the affected interface, returned with traps only.
INT apNotificationDot11ReasonCode	1.3.6.1.4.1.43.35.8.100.1.4	INTEGER	not-accessible	This attribute defines the reason for the failure of an operation. Value = 1: Invalid mode/state Value = 2: Station not authenticated. Value = 3: Internal error Value = 4: Out of sequence frame Value = 5: Un-supportd algorithm Value = 6: Invalid frame length Value = 7: WEP is required on the AP Value = 8: WEP not allowed Value = 9: Challenge text mismatch
INT apNotificationDot11RequestType	1.3.6.1.4.1.43.35.8.100.1.3	INTEGER	not-accessible	This attribute defines the request type sent by the station. Value = 1: Unknown request type Value = 2: Association Request Value = 3: Re-association Request Value = 4: Authentication
MAC apNotificationDot11Station	1.3.6.1.4.1.43.35.8.100.1.2	MacAddress	not-accessible	This attribute holds the MAC address of the wireless station
apNotificationObjects	1.3.6.1.4.1.43.35.8.100.1
apNotificationTrapObjects	1.3.6.1.4.1.43.35.8.100.2
apNotificationTrapTree	1.3.6.1.4.1.43.35.8.100
STR destFile	1.3.6.1.4.1.43.35.8.4.4	DisplayString	read-write	The destination file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
INT dot118021xBroadcastKeyRefreshRate	1.3.6.1.4.1.43.35.8.7.5.2	INTEGER	read-write	The number (in minutes) between changing the broadcast key for 802.1x and WPA clients
INT dot118021xReauthenticationTimeout	1.3.6.1.4.1.43.35.8.7.5.4	INTEGER	read-write	The number (in minutes) between forcing 802.1x clients to reauthenticate
INT dot118021xSessionKeyRefreshRate	1.3.6.1.4.1.43.35.8.7.5.3	INTEGER	read-write	The number (in minutes) between changing session keys for 802.1x and WPA clients
INT dot118021xState	1.3.6.1.4.1.43.35.8.7.5.1	INTEGER	read-write	This attribute indicates that the Enterprise the state of the 802.1x authentication algorithm.
I32 dot118021xSuppIndex	1.3.6.1.4.1.43.35.8.7.8.1.1	Integer32	not-accessible	Index of the interface for which this supplicant is running. Currently only the ethernet interface.
STR dot118021xSuppPasswd	1.3.6.1.4.1.43.35.8.7.8.1.4	DisplayString	read-write	This value indicates the password for supplicant. If value is configured, will display ****. Else will display EMPTY.
INT dot118021xSuppState	1.3.6.1.4.1.43.35.8.7.8.1.2	INTEGER	read-write	This object is used to enable or disable the 802.1x supplicant.
STR dot118021xSuppUser	1.3.6.1.4.1.43.35.8.7.8.1.3	DisplayString	read-write	This value indicates the username for supplicant. If value is configured, will display ****. Else will display EMPTY.
INT dot11AuthenticationAcctPort	1.3.6.1.4.1.43.35.8.7.6.1.7	INTEGER	read-write	The port number for radius server accounting.
dot11AuthenticationEntry	1.3.6.1.4.1.43.35.8.7.5
INT dot11AuthenticationInterimUpdate	1.3.6.1.4.1.43.35.8.7.6.1.8	INTEGER	read-write	This value indicates the Timeout value(sec) used by the radius server interim update.
STR dot11AuthenticationKey	1.3.6.1.4.1.43.35.8.7.6.1.4	DisplayString	read-write	This value indicates the shared key used by the authentication server.
INT dot11AuthenticationPort	1.3.6.1.4.1.43.35.8.7.6.1.3	INTEGER	read-write	This value indicates the UDP Port used by the authentication server.
INT dot11AuthenticationRetransmit	1.3.6.1.4.1.43.35.8.7.6.1.5	INTEGER	read-write	This value indicates the retransmit timer length used by the authentication server.
IP dot11AuthenticationServer	1.3.6.1.4.1.43.35.8.7.6.1.2	IpAddress	read-write	This value indicates the IP address of the authentication server.
dot11AuthenticationServerEntry	1.3.6.1.4.1.43.35.8.7.6.1		not-accessible	An entry in the table, containing information about configuration of one authentication server of the AP.
I32 dot11AuthenticationServerIndex	1.3.6.1.4.1.43.35.8.7.6.1.1	Integer32	not-accessible	Index of the Authentication Server
dot11AuthenticationServerTable	1.3.6.1.4.1.43.35.8.7.6		not-accessible	Table of descriptive and status information about configuration of each authentication server.
dot11AuthenticationSupplicantEntry	1.3.6.1.4.1.43.35.8.7.8.1		not-accessible	An entry in the table, containing information about configuration of one supplicant.
dot11AuthenticationSupplicantTable	1.3.6.1.4.1.43.35.8.7.8		not-accessible	Table of descriptive and status information about configuration of supplicant
INT dot11AuthenticationTimeout	1.3.6.1.4.1.43.35.8.7.6.1.6	INTEGER	read-write	This value indicates the Timeout value(sec) used by the authentication server.
dot11Filter	1.3.6.1.4.1.43.35.8.7.7
MAC dot11FilterAddress	1.3.6.1.4.1.43.35.8.7.7.2.1.1	MacAddress	not-accessible	This value indicates the MAC address of the filter entry.
INT dot11FilterDefault	1.3.6.1.4.1.43.35.8.7.7.1	INTEGER	read-write	This value indicates the default access for local mac filters.
dot11FilterEntry	1.3.6.1.4.1.43.35.8.7.7.2.1		not-accessible	An entry in the table, containing information about configuration in one radio of the AP.
INT dot11FilterStatus	1.3.6.1.4.1.43.35.8.7.7.2.1.2	INTEGER	read-write	This value indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to the network from the client.
dot11FilterTable	1.3.6.1.4.1.43.35.8.7.7.2		not-accessible	Table of status information about each configured MAC Address Filtering Entry.
NTF dot11InterfaceAGFail	1.3.6.1.4.1.43.35.8.100.2.8			The InterfaceAGFail notification shall be sent out when 802.11a/802.11g wireless interface has failed.
INT dot11MACAuthenticationType	1.3.6.1.4.1.43.35.8.7.5.5	INTEGER	read-write	This value indicates the type of mac authentication in use.
NTF dot11StationAssociation	1.3.6.1.4.1.43.35.8.100.2.4			The associate notification shall be sent when a station successfully associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
NTF dot11StationAuthentication	1.3.6.1.4.1.43.35.8.100.2.6			The authentication notification shall be sent when a station successfully authenticates with the Access Point. The value of the notification shall include the MAC address of the station that has authenticated.
NTF dot11StationReAssociation	1.3.6.1.4.1.43.35.8.100.2.5			The re-associate notification shall be sent when a station successfully re-associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
NTF dot11StationRequestFail	1.3.6.1.4.1.43.35.8.100.2.7			The station request fail shall be sent out when a station fails to associate / re-associate / authenticate with the Access Point. The notification shall include the MAC address of the station and the reason code for the failure.
NTF dot1xAuthFail	1.3.6.1.4.1.43.35.8.100.2.13			The 802.1x authentication failure notification shall be sent when a station fails to authenticate with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
NTF dot1xAuthNotInitiated	1.3.6.1.4.1.43.35.8.100.2.11			The 802.1x authentication not initiated notification shall be sent when a station did not initiate 802.1x authentication with the RADIUS server. The value of the notification shall include the MAC address of the station that did not initiate 802.1x authentication.
NTF dot1xAuthSuccess	1.3.6.1.4.1.43.35.8.100.2.12			The 802.1x authentication success notification shall be sent when a station successfully authenticates with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
NTF dot1xMacAddrAuthFail	1.3.6.1.4.1.43.35.8.100.2.10			The 802.1x MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
NTF dot1xMacAddrAuthSuccess	1.3.6.1.4.1.43.35.8.100.2.9			The 802.1x MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
enterpriseApAdmin	1.3.6.1.4.1.43.35.8.8
STR enterpriseApAdminPassword	1.3.6.1.4.1.43.35.8.8.2	DisplayString	read-write	This value indicates the password for management login. Accept empty string to remove the password.
STR enterpriseApAdminUser	1.3.6.1.4.1.43.35.8.8.1	DisplayString	read-write	This value indicates the username for management login.
enterpriseAPdot11	1.3.6.1.4.1.43.35.8.7
enterpriseApFileTransferMgt	1.3.6.1.4.1.43.35.8.4
enterpriseApIpMgt	1.3.6.1.4.1.43.35.8.6
enterpriseApLineMgnt	1.3.6.1.4.1.43.35.8.2
enterpriseApPortMgnt	1.3.6.1.4.1.43.35.8.3
enterpriseApProxyArp	1.3.6.1.4.1.43.35.8.12
enterpriseApRadio	1.3.6.1.4.1.43.35.8.10
INT enterpriseApRadioAntennaMode	1.3.6.1.4.1.43.35.8.10.1.1.7	INTEGER	read-write	This value indicates the antenna mode in use for the G-radio. The values are interpreted as follows: both(1) means use both built-in antennas, left(2) means use left side. right(3) means use right side. invalid(4) means not support. This setting is only valid for the 802.11g interface.
INT enterpriseApRadioAutoChannel	1.3.6.1.4.1.43.35.8.10.1.1.2	INTEGER	read-write	This value indicates whether auto channel selection is enabled or not for this radio interface
INT enterpriseApRadioDataRate	1.3.6.1.4.1.43.35.8.10.1.1.5	INTEGER	read-write	This value indicates the data rate for this radio interface. Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54. Radio interface G operates all listed data rates. The auto setting will attempt to set the best data rate for the interface
enterpriseApRadioEntry	1.3.6.1.4.1.43.35.8.10.1.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
INT enterpriseApRadioGMode	1.3.6.1.4.1.43.35.8.10.1.1.6	INTEGER	read-write	This value indicates the radio mode for the 802.11g radio. This setting is only valid for the 802.11g interface.
I32 enterpriseApRadioIndex	1.3.6.1.4.1.43.35.8.10.1.1.1	Integer32	not-accessible	Radio Index for configuration.
enterpriseApRadioTable	1.3.6.1.4.1.43.35.8.10.1		not-accessible	Table of descriptive and status information about configuration of each radio.
INT enterpriseApRadioTransmitPower	1.3.6.1.4.1.43.35.8.10.1.1.3	INTEGER	read-write	This value indicates the transmit power for this radio interface.
INT enterpriseApRadioTurboMode	1.3.6.1.4.1.43.35.8.10.1.1.4	INTEGER	read-write	This value indicates whether turbo mode is enabled for this radio interface.
enterpriseApResetMgt	1.3.6.1.4.1.43.35.8.5
enterpriseApRogueAp	1.3.6.1.4.1.43.35.8.13
enterpriseApSecurity	1.3.6.1.4.1.43.35.8.9
INT enterpriseApSecurityAuthType	1.3.6.1.4.1.43.35.8.9.1.1.2	INTEGER	read-write	This value indicates the type of authentication in use for this radio interface.
enterpriseApSecurityEntry	1.3.6.1.4.1.43.35.8.9.1.1		not-accessible	An entry in the table, containing information about configuration of one radio of the AP.
I32 enterpriseApSecurityIndex	1.3.6.1.4.1.43.35.8.9.1.1.1	Integer32	not-accessible	Radio Index for security settings.
INT enterpriseApSecuritySharedKeyLen	1.3.6.1.4.1.43.35.8.9.1.1.3	INTEGER	read-only	This value indicates the shared key length for this radio interface.
enterpriseApSecurityTable	1.3.6.1.4.1.43.35.8.9.1		not-accessible	Table of descriptive and status information about configuration of each radio in terms of security settings.
T/F enterpriseApSecurityWEPEnabled	1.3.6.1.4.1.43.35.8.9.1.1.10	TruthValue	read-write	This value indicates whether WEP is enabled.
INT enterpriseApSecurityWEPKeyType	1.3.6.1.4.1.43.35.8.9.1.1.9	INTEGER	read-write	This value indicates the type of WEP Key in use for this radio interface.
INT enterpriseApSecurityWPACipher	1.3.6.1.4.1.43.35.8.9.1.1.6	INTEGER	read-write	This value indicates the type of WPA Cipher in use for this radio interface.
INT enterpriseApSecurityWPAKeyType	1.3.6.1.4.1.43.35.8.9.1.1.5	INTEGER	read-write	This value indicates the type of WPA Key Management in use for this radio interface.
INT enterpriseApSecurityWPAMode	1.3.6.1.4.1.43.35.8.9.1.1.4	INTEGER	read-write	This value indicates the state of WPA for this radio interface.
STR enterpriseApSecurityWPAPSK	1.3.6.1.4.1.43.35.8.9.1.1.8	DisplayString	read-write	This value indicates WPA Pre Shared Key in use for this radio interface.
INT enterpriseApSecurityWPAPSKType	1.3.6.1.4.1.43.35.8.9.1.1.7	INTEGER	read-write	This value indicates the type of WPA Pre Shared Key in use for this radio interface.
enterpriseApSys	1.3.6.1.4.1.43.35.8.1
INT enterpriseApVapRadioClosedSystem	1.3.6.1.4.1.43.35.8.10.2.1.3	INTEGER	read-write	This value indicates whether closed system is enabled for this radio interface.
STR enterpriseApVapRadioDescription	1.3.6.1.4.1.43.35.8.10.2.1.6	DisplayString	read-write	This value indicates the description for this radio interface.
enterpriseApVapRadioEntry	1.3.6.1.4.1.43.35.8.10.2.1		not-accessible	An entry in the table, containing information about configuration of one Vap radio of the AP.
I32 enterpriseApVapRadioIndex	1.3.6.1.4.1.43.35.8.10.2.1.1	Integer32	not-accessible	Radio Index for configuration.
INT enterpriseApVapRadioMaxAssoc	1.3.6.1.4.1.43.35.8.10.2.1.4	INTEGER	read-write	This value indicates the max number of clients allowed on this radio interface.
INT enterpriseApVapRadioState	1.3.6.1.4.1.43.35.8.10.2.1.2	INTEGER	read-write	This value indicates the state of the radio interface.
enterpriseApVapRadioTable	1.3.6.1.4.1.43.35.8.10.2		not-accessible	Table of descriptive and status information about configuration of each Vap radio.
INT enterpriseApVapRadioTransmitKey	1.3.6.1.4.1.43.35.8.10.2.1.5	INTEGER	read-write	This value indicates default transmit key in use for this radio interface.
enterpriseApWebRedirection	1.3.6.1.4.1.43.35.8.11
IP fileServer	1.3.6.1.4.1.43.35.8.4.5	IpAddress	read-write	The IP address of the TFTP server for transfer when a download is next requested via this MIB. This value is set to `0.0.0.0' when no IP address has been specified.
INT fileType	1.3.6.1.4.1.43.35.8.4.2	INTEGER	read-write	Type of file to transfer.
NTF iappContextDataSent	1.3.6.1.4.1.43.35.8.100.2.19			The IAPP Context Data Sent notification shall be sent out whenever the context data for a station has been sent to the new AP with which the station has associated. The notification shall include the MAC address of the station and the IP address of the new AP.
NTF iappStationRoamedFrom	1.3.6.1.4.1.43.35.8.100.2.17			The IAPP Station Roamed-From Notification shall be sent out whenever a station roams from another Access Point (AP) to this AP. The notification shall include the MAC address of the station and the IP address of the old AP.
NTF iappStationRoamedTo	1.3.6.1.4.1.43.35.8.100.2.18			The IAPP Station Roamed-To Notification shall be sent out whenever a station roams to another Access Point (AP) from this AP. The notification shall include the MAC address of the station and the IP address of the new AP.
I32 lineDataBits	1.3.6.1.4.1.43.35.8.2.1.1.2	Integer32	read-only	This is defined as number of data bits for the RS232 interface.
lineEntry	1.3.6.1.4.1.43.35.8.2.1.1		not-accessible	An entry in the table, containing information about configuration in one RS232 line of the Access Point.
I32 lineIndex	1.3.6.1.4.1.43.35.8.2.1.1.1	Integer32	not-accessible	This is defined as RS-232 index.
INT lineParity	1.3.6.1.4.1.43.35.8.2.1.1.3	INTEGER	read-only	This is defined as parity of the RS232 interface.
I32 lineSpeed	1.3.6.1.4.1.43.35.8.2.1.1.4	Integer32	read-only	This is defined as the speed of the RS-232 interface.
I32 lineStopBits	1.3.6.1.4.1.43.35.8.2.1.1.5	Integer32	read-only	This is defined as the number of stop bits for the RS-232 interface.
lineTable	1.3.6.1.4.1.43.35.8.2.1		not-accessible	Table of descriptive and status information about configuration of each RS-232 line in this system
NTF localMacAddrAuthFail	1.3.6.1.4.1.43.35.8.100.2.15			The Local MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
NTF localMacAddrAuthSuccess	1.3.6.1.4.1.43.35.8.100.2.14			The Local MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
IP netConfigDefaultGateway	1.3.6.1.4.1.43.35.8.6.3	IpAddress	read-write	The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
INT netConfigDHCPState	1.3.6.1.4.1.43.35.8.6.8	INTEGER	read-write	Whether DHCP is enabled.
INT netConfigHttpPort	1.3.6.1.4.1.43.35.8.6.5	INTEGER	read-write	The port number for HTTP. Default value is 80.
INT netConfigHttpsPort	1.3.6.1.4.1.43.35.8.6.7	INTEGER	read-write	The port number for Secure HTTP. Default value is 443.
INT netConfigHttpsState	1.3.6.1.4.1.43.35.8.6.6	INTEGER	read-write	Whether Secure HTTP is enabled.
INT netConfigHttpState	1.3.6.1.4.1.43.35.8.6.4	INTEGER	read-write	Whether HTTP is enabled.
IP netConfigIPAddress	1.3.6.1.4.1.43.35.8.6.1	IpAddress	read-write	The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
IP netConfigSubnetMask	1.3.6.1.4.1.43.35.8.6.2	IpAddress	read-write	The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
STR password	1.3.6.1.4.1.43.35.8.4.7	DisplayString	read-write	The password specified for an FTP Transfer.
INT portAutonegotiation	1.3.6.1.4.1.43.35.8.3.1.1.7	INTEGER	read-only	Whether autonegotiation is enabled.
INT portCapabilities	1.3.6.1.4.1.43.35.8.3.1.1.6	INTEGER	read-only	Port capabilities.
portEntry	1.3.6.1.4.1.43.35.8.3.1.1		not-accessible	An entry in the table, containing information about configuration in one switch port of the switch.
INT portFlowCtrlCfg	1.3.6.1.4.1.43.35.8.3.1.1.5	INTEGER	read-only	(1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (3) Flow control mechanism is backPressure. when the port is in fullDuplex mode.This flow control mechanism will not function. (4) Flow control mechanism is IEEE 802.3x flow control. when the port is in halfDuplex mode.This flow control mechanism will not function. hundredBaseTX and thousandBaseSX port can be set as: enabled(1), disabled(2), backPressure(3), dot3xFlowControl(4). hundredBaseFX port can be set as: enabled(1), disabled(2), backPressure(3). The actual flow control mechanism is used given by portFlowCtrlStatus.
INT portFlowCtrlStatus	1.3.6.1.4.1.43.35.8.3.1.1.9	INTEGER	read-only	(2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
I32 portIndex	1.3.6.1.4.1.43.35.8.3.1.1.1	Integer32	not-accessible	This is defined as ifIndex in the IF-MIB.
STR portName	1.3.6.1.4.1.43.35.8.3.1.1.2	DisplayString	read-only	Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).
INT portSpeedDpxCfg	1.3.6.1.4.1.43.35.8.3.1.1.4	INTEGER	read-only	Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode hundredBaseTX port can be set as halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as halfDuplex100(4) fullDuplex100(5) thousandBaseSX port can be set as halfDuplex1000(6) fullDuplex1000(7) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.
INT portSpeedDpxStatus	1.3.6.1.4.1.43.35.8.3.1.1.8	INTEGER	read-only	The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this value is error(1).
portTable	1.3.6.1.4.1.43.35.8.3.1		not-accessible	Table of descriptive and status information about configuration of each switch port (including expansion slot) in this system. This table also contains information about each trunk (similar to Cisco's EtherChannel).
INT portType	1.3.6.1.4.1.43.35.8.3.1.1.3	INTEGER	read-only	Indicates the port type.
NTF pppLogonFail	1.3.6.1.4.1.43.35.8.100.2.16			The PPP Logon failure notification shall be sent out when the AP fails to login successfully to the PPP peer using the supplied username and password.
INT proxyArpEnabled	1.3.6.1.4.1.43.35.8.12.1	INTEGER	read-write	Whether ProxyArp is enabled.
radioWdsEntry	1.3.6.1.4.1.43.35.8.10.3.1		not-accessible	An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable). The table does not contain the radio index as a member of the table.
radioWdsPeerEntry	1.3.6.1.4.1.43.35.8.10.4.1		not-accessible	An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable) and the peer index (Up to 6). The table does not contain the radio index as a member of the table.
radioWdsPeerTable	1.3.6.1.4.1.43.35.8.10.4		not-accessible	Table of configuration information for Wds Peers for each Radio interface.
radioWdsTable	1.3.6.1.4.1.43.35.8.10.3		not-accessible	Table of configuration information for Wds for each Radio interface.
INT restartControl	1.3.6.1.4.1.43.35.8.5.2	INTEGER	read-write	Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
STR restartOpCodeFile	1.3.6.1.4.1.43.35.8.5.1	DisplayString	read-write	Name of op-code file for start-up.
rivet	1.3.6.1.4.1.43.35.8			The management information definitions for the 3COM AP-PRIVATE-MIB.
STR rogueApBssid	1.3.6.1.4.1.43.35.8.13.1.1.2	DisplayString	read-only	The AP BSSID
I32 rogueApChannelNumber	1.3.6.1.4.1.43.35.8.13.1.1.5	Integer32	read-only	Channel where Ap detected.
rogueApDetectionTable	1.3.6.1.4.1.43.35.8.13.1		not-accessible	Table of each AP that has been detected.
INT rogueApDuration	1.3.6.1.4.1.43.35.8.10.1.1.10	INTEGER	read-write	How long to scan each channel (in milliseconds). A longer duration will yield more complete results. A shorter duration will allow clients a better chance of remaining connected. Default value is 350(milliseconds).
rogueApEntry	1.3.6.1.4.1.43.35.8.13.1.1		not-accessible	An entry in the table, containing information about any AP detected.
INT rogueApIndex	1.3.6.1.4.1.43.35.8.13.1.1.1	INTEGER	not-accessible	Monotonically increasing index.
INT rogueApInterval	1.3.6.1.4.1.43.35.8.10.1.1.9	INTEGER	read-write	How often to scan for Rogue Aps. The interval in minutes, with default of 720(minutes).
I32 rogueApPortNumber	1.3.6.1.4.1.43.35.8.13.1.1.4	Integer32	read-only	Interface index for the radio.
I32 rogueApRSSIValue	1.3.6.1.4.1.43.35.8.13.1.1.6	Integer32	read-only	RSSI for AP detected.
INT rogueApScanNow	1.3.6.1.4.1.43.35.8.10.1.1.11	INTEGER	read-write	When writing the value to enable, the AP will trigger the Rouge AP scan function. The value will always return disable(2).
STR rogueApSsid	1.3.6.1.4.1.43.35.8.13.1.1.3	DisplayString	read-only	The AP SSID
INT rogueApState	1.3.6.1.4.1.43.35.8.10.1.1.8	INTEGER	read-write	This value is used to enable/disable Rogue Ap Detection for this radio interface.
NTF sntpServerFail	1.3.6.1.4.1.43.35.8.100.2.20			The sntpServerFail notification shall be sent when the AP fails to get time from the configured SNTP server.
STR srcFile	1.3.6.1.4.1.43.35.8.4.3	DisplayString	read-write	The source file name for TFTP transfer when a transfer is next requested via this MIB. This value is set to the zero length string when no file name has been specified.
INT status	1.3.6.1.4.1.43.35.8.4.8	INTEGER	read-only	The status of the transfer.
STR swBootRomVer	1.3.6.1.4.1.43.35.8.1.2	DisplayString	read-only	Boot ROM code version of the main board.
STR swHardwareVer	1.3.6.1.4.1.43.35.8.1.1	DisplayString	read-only	Hardware version of the main board.
STR swOpCodeVer	1.3.6.1.4.1.43.35.8.1.3	DisplayString	read-only	Operation code version of the main board.
STR swSerialNumber	1.3.6.1.4.1.43.35.8.1.4	DisplayString	read-only	Serial Number of the Access Point.
NTF sysRadiusServerChanged	1.3.6.1.4.1.43.35.8.100.2.3			The RADIUS server changed notification shall be sent when the RADIUS server has changed from Primary / Secondary to Secondary / Primary.
NTF sysSystemDown	1.3.6.1.4.1.43.35.8.100.2.2			The system down notification shall be sent before the AP is about to reboot.
NTF sysSystemUp	1.3.6.1.4.1.43.35.8.100.2.1			The system up notification shall be sent when the AP is fully up and running.
INT transferStart	1.3.6.1.4.1.43.35.8.4.9	INTEGER	read-write	To start a transfer.
INT transferType	1.3.6.1.4.1.43.35.8.4.1	INTEGER	read-write	Type of file to transfer.
STR userName	1.3.6.1.4.1.43.35.8.4.6	DisplayString	read-write	The username specified for an FTP Transfer.
INT wdsApRole	1.3.6.1.4.1.43.35.8.10.3.1.1	INTEGER	read-write	This value indicates the role of the Ap for this radio: normal operation(1), bridge master(2) which accepts only repeaters to associate with, repeater Ap(3) that accepts wireless station and other repeaters if it is root-connected: bridge-connected or root connected, and bridge(4) which bridges ethernet traffic to WDS parent bridge but does not relay wireless traffic.
STR wdsPeerBssid	1.3.6.1.4.1.43.35.8.10.4.1.2	DisplayString	read-write	The BSSID for this peer.
I32 wdsPeerIndex	1.3.6.1.4.1.43.35.8.10.4.1.1	Integer32	not-accessible	Peer Index for the radio interface.
INT webRedirectionEnabled	1.3.6.1.4.1.43.35.8.11.1	INTEGER	read-write	Whether Web Redirection is enabled.
wlan_mib	1.3.6.1.4.1.43.35

RFC description

3Com access point wireless LAN management with configuration, security, and radio controls.

Start monitoring Legacy 3Com switches and wireless APs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-PRIVATE-MIB

What Is A3COM-PRIVATE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description