A3COM-HUAWEI-DOT11-RRM-MIB

All MIBs › A3COM-HUAWEI-DOT11-RRM-MIB

Organization: Hangzhou H3C Technologies Co., Ltd.

Last Updated: 2010-09-25

Category: Vendor: H3C/HH3C, Wireless and WLAN

Description: Manages 802.11 Radio Resource Management including channel, power, and load-balancing policies on H3C APs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is A3COM-HUAWEI-DOT11-RRM-MIB?

A3COM-HUAWEI-DOT11-RRM-MIB is an H3C WLAN MIB implementing 802.11 Radio Resource Management (RRM), which automates channel selection, transmit power, and interference avoidance across access points. It exposes configuration objects for protocol modes (like 11n MCS rates and 11g protection), power constraints, spectrum management, and scan behavior, alongside interference-threshold settings for APs and stations. Its monitoring emphasis is radio-frequency health and performance: administrators track interference thresholds and scan results to detect RF congestion or misconfigured channels affecting wireless service quality, functioning as a software/radio-status view rather than physical hardware sensors. It is a self-contained WLAN feature MIB with no strong indication of dependency on other standard MIBs beyond the general 802.11 WLAN MIB family it belongs to. It is deployed on H3C wireless access controllers and APs in environments needing automated RF tuning across many radios, forming the basis of A3COM-HUAWEI-DOT11-RRM-MIB SNMP monitoring for wireless network administrators.

IPNetwork Monitor allows you to monitor SNMP objects defined in A3COM-HUAWEI-DOT11-RRM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C wireless access controllers and access points

Monitoring Examples

An operator would poll h3cDot11APInterfNumThreshhd and h3cDot11StaInterfNumThreshhd to see the configured interference thresholds, then check the h3cDot11RRMRadioCfgTable for per-radio settings like h3cDot11RRM11nMadtMaxMcs and h3cDot11RRM11aPwrConstrt. Frequent triggering relative to h3cDot11RRMScanChl and h3cDot11RRMScanRptIntvel scan results would indicate an AP is experiencing high co-channel interference and may need a channel change. h3cDot11RRMAutoChlAvoid11h shows whether automatic channel avoidance (DFS/radar avoidance) is enabled for regulatory compliance.

What Can Be Monitored

AP/station interference thresholds
per-radio MCS and power configuration
RF scan channel and interval settings
automatic channel avoidance status
11g protection mode

Imported Objects

From A3COM-HUAWEI-DOT11-REF-MIB

H3cDot11ChannelScopeType
H3cDot11ObjectIDType
H3cDot11RadioElementIndex
H3cDot11RadioScopeType
H3cDot11RadioType
H3cDot11SSIDStringType
h3cDot11	MODULE-IDENTITY
h3cDot11APElementIndex	OBJECT-TYPE

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
I32 h3cDot11APInterfNumThreshhd	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.9	Integer32	read-write	Represents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node is zero, AP interference trap will be sent immediately.
h3cDot11MonitorDetectedDevEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1		not-accessible	Each entry contains information of detected devices.
h3cDot11MonitorDetectedDevTable	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1		not-accessible	This table shows the devices of AP detected
h3cDot11MonitorDetectedGroup	1.3.6.1.4.1.43.45.1.10.2.75.8.4
I32 h3cDot11MonitorDevBeaconIntvl	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.9	Integer32	read-only	Represents the beacon interval for the detected device(not include the device which type is client).
MAC h3cDot11MonitorDevBSSID	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.5	MacAddress	read-only	Represents the basic service set identifier of the detected device.
H3C h3cDot11MonitorDevChannel	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.6	H3cDot11ChannelScopeType	read-only	Represents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels.
T/F h3cDot11MonitorDevClear	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.12	TruthValue	read-write	This object is used to clear the information of the device detected in the WLAN. It will return false for get operation.
DAT h3cDot11MonitorDevFstDctTime	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.10	DateAndTime	read-only	Represents the time at which the device was first detected.
DAT h3cDot11MonitorDevLstDctTime	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.11	DateAndTime	read-only	Represents the time at which the device was detected last time.
MAC h3cDot11MonitorDevMAC	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.1	MacAddress	not-accessible	Represents MAC address of the device detected.
I32 h3cDot11MonitorDevMaxRSSI	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.8	Integer32	read-only	Represents the maximum detected RSSI of the device in a scan report cycle.
I32 h3cDot11MonitorDevSNR	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.13	Integer32	read-only	Represents the SNR of the device in a scan report cycle.
OCT h3cDot11MonitorDevSSID	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.4	OCTET STRING	read-only	Represents the service set identifier for the ESS of the device which type is ap or adhoc.
INT h3cDot11MonitorDevType	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.2	INTEGER	read-only	Represents type of the device detected.
OCT h3cDot11MonitorDevVendor	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.3	OCTET STRING	read-only	Represents vendor of the detected device.
H3C h3cDot11MonitorRadioId	1.3.6.1.4.1.43.45.1.10.2.75.8.4.1.1.7	H3cDot11RadioScopeType	read-only	Represents the radio ID of the AP that detected the device.
I32 h3cDot11NewPower	1.3.6.1.4.1.43.45.1.10.2.75.8.3.3.1	Integer32	accessible-for-notify	Power of the radio after the change of power.
I32 h3cDot11OldPower	1.3.6.1.4.1.43.45.1.10.2.75.8.3.3.2	Integer32	accessible-for-notify	Power of the radio before the change of power.
h3cDot11RRM	1.3.6.1.4.1.43.45.1.10.2.75.8			This MIB file is to provide the object definition of WLAN radio resource management (RRM).
I32 h3cDot11RRM11aPwrConstrt	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.4	Integer32	read-write	Configure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of power constraint is 0 to MAX-POWER-1 (where the MAX-POWER is defined by the regulatory domain).
T/F h3cDot11RRM11aSpectrumManag	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.5	TruthValue	read-write	Enable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and power constraints applicable to all devices in the BSS based on regulatory domain specification.
T/F h3cDot11RRM11gProtect	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.3	TruthValue	read-write	Enable/Disable dot11g protection.
I32 h3cDot11RRM11nMadtMaxMcs	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.1	Integer32	read-write	Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.
I32 h3cDot11RRM11nSuptMaxMcs	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.2	Integer32	read-write	Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.
I32 h3cDot11RRMAdjChlIntfTrapThhd	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5.1.5	Integer32	read-write	Represents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
h3cDot11RRMAPCfg2Entry	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5.1		not-accessible	Each entry contains information of RRM parameters for AP.
h3cDot11RRMAPCfg2Table	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5		not-accessible	This table defines the RRM parameters for AP.
h3cDot11RRMAPCfgEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.1.3.1		not-accessible	Each entry contains information of RRM parameters for AP.
h3cDot11RRMAPCfgTable	1.3.6.1.4.1.43.45.1.10.2.75.8.1.3		not-accessible	This table defines the RRM parameters for AP.
I32 h3cDot11RRMAPIntfThreshold	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5.1.2	Integer32	read-write	Represents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.
H3C h3cDot11RRMAPSerialID	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5.1.1	H3cDot11ObjectIDType	not-accessible	Serial ID of the AP.
INT h3cDot11RRMAPWorkMode	1.3.6.1.4.1.43.45.1.10.2.75.8.1.3.1.1	INTEGER	read-write	AP work mode.
T/F h3cDot11RRMAutoChlAvoid11h	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.6	TruthValue	read-write	Configure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel selection and one of them is selected.
I32 h3cDot11RRMCfgAdjacencyFctr	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.13	Integer32	read-write	Configure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor.
INT h3cDot11RRMCfgChlMode	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.3	INTEGER	read-write	Configure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.
T/F h3cDot11RRMCfgChlState	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.2	TruthValue	read-write	Enable/Disable dynamic channel selection.
I32 h3cDot11RRMCfgIntrfThres	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.9	Integer32	read-write	Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.
I32 h3cDot11RRMCfgIntrvl	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.8	Integer32	read-write	Configure the calibration interval.
I32 h3cDot11RRMCfgNoiseThres	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.10	Integer32	read-write	Configure the noise threshold.
I32 h3cDot11RRMCfgPERThres	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.11	Integer32	read-write	Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.
INT h3cDot11RRMCfgPwrMode	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.6	INTEGER	read-write	Configure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.
T/F h3cDot11RRMCfgPwrState	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.5	TruthValue	read-write	Enable/Disable dynamic power selection for the band.
I32 h3cDot11RRMCfgToleranceFctr	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.12	Integer32	read-write	Configure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user.
U32 h3cDot11RRMChlProntoRadioElmt	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.4	Unsigned32	read-write	Specify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.
h3cDot11RRMChlQltyNotifications	1.3.6.1.4.1.43.45.1.10.2.75.8.3.1
h3cDot11RRMChlQltyNtfPrefix	1.3.6.1.4.1.43.45.1.10.2.75.8.3.1.0
I32 h3cDot11RRMChlRptChlNum	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.2	Integer32	accessible-for-notify	Channel number.
INT h3cDot11RRMChlRptChlQlty	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.4	INTEGER	read-only	Channel quality.
INT h3cDot11RRMChlRptChlType	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.3	INTEGER	read-only	Channel type.
h3cDot11RRMChlRptEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1		not-accessible	Each entry contains information of RRM channel information of the radio on the AP.
I32 h3cDot11RRMChlRptIntrf	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.8	Integer32	read-only	Interference observed on the channel in percentage.
I32 h3cDot11RRMChlRptLoad	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.6	Integer32	read-only	Load observed on the channel in percentage.
I32 h3cDot11RRMChlRptNbrCnt	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.5	Integer32	read-only	Number of neighbors found on the channel.
I32 h3cDot11RRMChlRptNoise	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.11	Integer32	read-only	Noise observed on the channel.
I32 h3cDot11RRMChlRptPER	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.9	Integer32	read-only	Packet error rate observed on the channel in percentage.
INT h3cDot11RRMChlRptRadarIndtcr	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.12	INTEGER	read-write	Radar detection status.
I32 h3cDot11RRMChlRptRetryRate	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.10	Integer32	read-only	Percentage of retransmission happened on the channel.
h3cDot11RRMChlRptTable	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1		not-accessible	This table shows the RRM channel information of each radio on all APs.
I32 h3cDot11RRMChlRptUtlz	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.7	Integer32	read-only	Utilization of the channel in percentage.
I32 h3cDot11RRMCoChlIntfTrapThhd	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5.1.4	Integer32	read-write	Represents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
h3cDot11RRMConfigGroup	1.3.6.1.4.1.43.45.1.10.2.75.8.1
h3cDot11RRMDetectGroup	1.3.6.1.4.1.43.45.1.10.2.75.8.2
h3cDot11RRMGlobalCfgPara	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1
DAT h3cDot11RRMHistoryChgDateTime	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.12	DateAndTime	read-only	The time when the channel or power change occurred.
BIT h3cDot11RRMHistoryChgReason	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.11	Bits	read-only	Reason for the change of channel or power. The various bit positions are: \|0 \|Others \| \|1 \|Coverage \| \|2 \|Radar \| \|3 \|Retransmission \| \|4 \|Packets discarded \| \|5 \|Interference \| 0 is returned when the history record type is after.
H3C h3cDot11RRMHistoryChl	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.3	H3cDot11ChannelScopeType	read-only	Channel on which the radio operates before/after the change of channel or power.
h3cDot11RRMHistoryEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1		not-accessible	Each entry shows the details of channel and power changes.
I32 h3cDot11RRMHistoryId	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.1	Integer32	not-accessible	History number of the change.
I32 h3cDot11RRMHistoryIntrf	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.7	Integer32	read-only	Interference observed on the radio in percentage before/after the change of channel or power.
I32 h3cDot11RRMHistoryLoad	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.5	Integer32	read-only	Load observed on the radio in percentage before/after the change of channel or power.
I32 h3cDot11RRMHistoryNoise	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.8	Integer32	read-only	Noise observed on the radio before/after the change of channel or power.
I32 h3cDot11RRMHistoryPER	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.9	Integer32	read-only	Packet error rate observed on the radio in percentage before/after the change of channel or power.
I32 h3cDot11RRMHistoryPwr	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.4	Integer32	read-only	Power of the radio before/after the change of channel or power.
INT h3cDot11RRMHistoryRecIndctr	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.2	INTEGER	not-accessible	History record type of the change.
I32 h3cDot11RRMHistoryRetryRate	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.10	Integer32	read-only	Percentage of retransmission happened on the radio before/after the change of channel or power.
h3cDot11RRMHistoryTable	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3		not-accessible	This table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the channel, power, interference parameters.
I32 h3cDot11RRMHistoryUtlz	1.3.6.1.4.1.43.45.1.10.2.75.8.2.3.1.6	Integer32	read-only	Utilization of the radio in percentage before/after the change of channel or power.
NTF h3cDot11RRMIntrfLimit	1.3.6.1.4.1.43.45.1.10.2.75.8.3.1.0.1			This notification will be sent when interference on the radio exceeds the limit.
MAC h3cDot11RrmNbrBSSID	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1.1	MacAddress	not-accessible	MAC address of the AP.
H3C h3cDot11RrmNbrChl	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1.2	H3cDot11ChannelScopeType	read-only	Channel number on which the neighbor was found.
h3cDot11RRMNbrInfoEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1		not-accessible	Each entry contains information of RRM neighbor information of the radio on an AP.
h3cDot11RRMNbrInfoTable	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2		not-accessible	This table shows the RRM neighbor information of each radio on all APs.
I32 h3cDot11RRMNbrIntrf	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1.3	Integer32	read-only	Interference observed on the channel in percentage by neighbor.
I32 h3cDot11RrmNbrRSSI	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1.4	Integer32	read-only	Signal strength of the AP in dBm.
STR h3cDot11RrmNbrSSID	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1.6	H3cDot11SSIDStringType	read-only	SSID of the Neighbor.
INT h3cDot11RrmNbrType	1.3.6.1.4.1.43.45.1.10.2.75.8.2.2.1.5	INTEGER	read-only	Type of the AP, managed or unmanaged.
NTF h3cDot11RRMNoiseLimit	1.3.6.1.4.1.43.45.1.10.2.75.8.3.1.0.3			This notification will be sent when noise on the radio exceeds the limit.
h3cDot11RRMNotificationsVar	1.3.6.1.4.1.43.45.1.10.2.75.8.3.3
h3cDot11RRMNotifyGroup	1.3.6.1.4.1.43.45.1.10.2.75.8.3
NTF h3cDot11RRMPERLimit	1.3.6.1.4.1.43.45.1.10.2.75.8.3.1.0.2			This notification will be sent when packet error rate on the radio exceeds the limit.
NTF h3cDot11RRMPowerChange	1.3.6.1.4.1.43.45.1.10.2.75.8.3.2.0.1			This notification will be sent when power changed on the radio automatically.
U32 h3cDot11RRMPwrProntoRadioElmt	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.7	Unsigned32	read-write	Specify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.
h3cDot11RRMRadioCfgEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1		not-accessible	Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
h3cDot11RRMRadioCfgTable	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2		not-accessible	Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
H3C h3cDot11RRMRadioIndex	1.3.6.1.4.1.43.45.1.10.2.75.8.2.1.1.1	H3cDot11RadioElementIndex	accessible-for-notify	Represents index of the radio.
H3C h3cDot11RRMRadioType	1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.1	H3cDot11RadioType	not-accessible	802.11 radio type.
h3cDot11RRMResChgNotifications	1.3.6.1.4.1.43.45.1.10.2.75.8.3.2
h3cDot11RRMResChgNtfPrefix	1.3.6.1.4.1.43.45.1.10.2.75.8.3.2.0
INT h3cDot11RRMScanChl	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.7	INTEGER	read-write	Set the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the radio band are scanned.
I32 h3cDot11RRMScanRptIntvel	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.8	Integer32	read-write	Set the scan report interval.
OCT h3cDot11RRMSDRadioGroupDesc	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4.1.2	OCTET STRING	read-create	Represents the description of RRM self-decisive radio group.
h3cDot11RRMSDRadioGroupEntry	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4.1		not-accessible	Each entry contains information of one RRM self-decisive radio group.
U32 h3cDot11RRMSDRadioGroupId	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4.1.1	Unsigned32	not-accessible	Represents RRM self-decisive radio group ID.
h3cDot11RRMSDRadioGroupTable	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4		not-accessible	This table defines RRM self-decisive radio group.
ROW h3cDot11RRMSDRdGroupRowStatus	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4.1.5	RowStatus	read-create	The row status of this table entry.
U32 h3cDot11RRMSDRdGrpChlHolddownTm	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4.1.3	Unsigned32	read-create	Represents the channel holddown time of RRM self-decisive radio group.
U32 h3cDot11RRMSDRdGrpPwrHolddownTm	1.3.6.1.4.1.43.45.1.10.2.75.8.1.4.1.4	Unsigned32	read-create	Represents the power holddown time of RRM self-decisive radio group.
I32 h3cDot11RRMStaIntfThreshold	1.3.6.1.4.1.43.45.1.10.2.75.8.1.5.1.3	Integer32	read-write	Represents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.
I32 h3cDot11StaInterfNumThreshhd	1.3.6.1.4.1.43.45.1.10.2.75.8.1.1.10	Integer32	read-write	Represents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this node is zero, STA interference trap will be sent immediately.

RFC description

Defines WLAN radio resource management (RRM) including interference detection, AP configuration, and channel management.

Start monitoring H3C wireless controllers and APs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download A3COM-HUAWEI-DOT11-RRM-MIB

What Is A3COM-HUAWEI-DOT11-RRM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description