All MIBs › VALERE-DC-POWER-MIB
Organization: Valere Power Inc.
Last Updated: 2005-12-02
Category: Power and Environmental Monitoring
Description: Monitors Valere DC power system rectifiers, batteries, load current, and alarm conditions.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is VALERE-DC-POWER-MIB?
This is a vendor MIB from Valere Power for its DC power system product line, covering rectifiers, batteries, load current, and associated alarm conditions used in telecom power plants. It exposes rectifier and module inventory data, battery/load current readings, and a trap table used to notify an NMS of power alarm conditions. It is fundamentally a hardware health monitoring MIB - its purpose is to track rectifier operational status, power module inventory, and alarm/trap conditions that reveal a failing rectifier, low battery, or overload before it causes a site outage. It appears to be a self-contained enterprise MIB with no stated dependency on other standard MIBs beyond its own historical revisions, which added rectifier and module inventory tables over time. It is deployed in telecom central office and cell site environments where DC rectifier/battery plants power core network and radio equipment, and technicians can download the VALERE-DC-POWER-MIB file directly to load it into their SNMP management tools.
IPNetwork Monitor allows you to monitor SNMP objects defined in VALERE-DC-POWER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Valere DC power systems / rectifier cabinets
- telecom power plant equipment
Monitoring Examples
Based on the module's revision history, a realistic scenario would poll the rectifier inventory table to confirm every rectifier module in the plant is present and healthy, and watch the vpwrTrapTable (formerly vpwrTrapDestinationTable) for alarm traps signaling a rectifier failure, battery discharge, or overload condition before it escalates into a power outage affecting downstream network equipment.
What Can Be Monitored
- rectifier operational status
- battery/load current
- power alarm conditions
- rectifier inventory
- module inventory
This MIB depends on
Related MIBs
Imported Objects
From RFC1213-MIB
| sysUpTime |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE | |
| enterprises |
From SNMPv2-TC
| AutonomousType | |
| DisplayString | |
| TEXTUAL-CONVENTION | |
| TestAndIncr | |
| TimeInterval | |
| TimeStamp |
How to Use in IPNetwork Monitor
Example using vpwrModuleOperHours OID:
Select a Valere DC power systems / rectifier cabinets, telecom power plant equipment (rectifier/battery alarm status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vpwrModuleOperHours into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the cumulative Operating Hours. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT batteryTempCompensation | 1.3.6.1.4.1.13858.7.1.4 | INTEGER | read-write | This parameter enables/disables temperature compensation. |
| INT batteryTempCompHighSlope | 1.3.6.1.4.1.13858.7.1.7 | INTEGER | read-write | The rate at which float voltage is changed, within the specified limits, when temperature compensation is active. |
| INT batteryTempCompHighStartTemperature | 1.3.6.1.4.1.13858.7.1.5 | INTEGER | read-write | The temperature at which temperature compensation becomes active. |
| INT batteryTempCompHighStopVoltage | 1.3.6.1.4.1.13858.7.1.6 | INTEGER | read-write | When temperature compensation is active, batteryTempCompHighStopVoltage is the limit to which float voltage will be reduced. For example, to set this voltage to 51.75 volts enter a value of 5175. |
| INT batteryTempCompLowSlope | 1.3.6.1.4.1.13858.7.1.10 | INTEGER | read-write | The rate at which float voltage is changed, within the specified limits, when temperature compensation is active. |
| INT batteryTempCompLowStartTemperature | 1.3.6.1.4.1.13858.7.1.8 | INTEGER | read-write | The temperature at which temperature compensation becomes active. |
| INT batteryTempCompLowStopVoltage | 1.3.6.1.4.1.13858.7.1.9 | INTEGER | read-write | When temperature compensation is active, batteryTempCompLowStopVoltage is the limit to which float voltage will be reduced. For example, to set this voltage to 51.75 volts enter a value of 5175. |
| INT batteryTempCompRunawayState | 1.3.6.1.4.1.13858.7.1.14 | INTEGER | read-only | This parameter selects the temperature sensing point for temperature compensation (in)activation. |
| INT batteryTempCompRunawayStopVoltage | 1.3.6.1.4.1.13858.7.1.12 | INTEGER | read-write | When temperature compensation is enabled, float voltage will be reduced to batteryTempCompRunawayStopVoltage if temperature reaches batteryTempCompRunawayTemperature. |
| INT batteryTempCompRunawayTemperature | 1.3.6.1.4.1.13858.7.1.11 | INTEGER | read-write | The temperature at which system voltage will be set to batteryTempCompRunawayStopVoltage. |
| INT batteryTempCompSenseSource | 1.3.6.1.4.1.13858.7.1.13 | INTEGER | read-write | This parameter selects the temperature sensing point for temperature compensation (in)activation. |
| INT sysAlarmComFailState | 1.3.6.1.4.1.13858.8.6 | INTEGER | read-write | Enable/Disable generation of comm fail alarm. |
| sysAlarmConfigEntry | 1.3.6.1.4.1.13858.8.4.1 | not-accessible | An entry containing information applicable to a particular temperature probe. | |
| sysAlarmConfigTable | 1.3.6.1.4.1.13858.8.4 | not-accessible | This table describes battery temperature probes. | |
| STR sysAlarmCustomName | 1.3.6.1.4.1.13858.8.4.1.3 | DisplayString | read-write | A string identifying probe location. |
| STR sysAlarmDefaultName | 1.3.6.1.4.1.13858.8.4.1.2 | DisplayString | read-only | A string identifying probe location. |
| INT sysAlarmIndex | 1.3.6.1.4.1.13858.8.4.1.1 | INTEGER | read-only | Index into temperature table |
| INT sysAlarmIShareState | 1.3.6.1.4.1.13858.8.7 | INTEGER | read-write | Enable/Disable generation of current share alarm. |
| INT sysAlarmOperStatus | 1.3.6.1.4.1.13858.8.4.1.6 | INTEGER | read-only | Indicates current alarm status |
| INT sysAlarmRedundancyState | 1.3.6.1.4.1.13858.8.8 | INTEGER | read-write | Enable/Disable generation of redundancy alarm. |
| INT sysAlarmSeverity | 1.3.6.1.4.1.13858.8.4.1.4 | INTEGER | read-write | Alarm Severity as denoted by Major and Minor Alarm Mask |
| STR sysAlarmToRelayMapping | 1.3.6.1.4.1.13858.8.4.1.5 | DisplayString | read-write | No additional mapping = 0 Map to Relay A = 1 Map to Relay B = 2 Map to Relay C = 4 Map to Relay D = 8 Map to Relay E = 16 Map to Relay F = 32 Map to Relay A and B = (1 + 2) and so on The major/minor classification of alarms automatically associates it with Major/Minor relay. Assigning a null mapping here does not override sysRelayAlarmSeverity for the alarm. It should be used to define mapping to additional relays. |
| sysAuxAlarmConfigEntry | 1.3.6.1.4.1.13858.8.5.1 | not-accessible | An entry containing information applicable to a particular temperature probe. | |
| sysAuxAlarmConfigTable | 1.3.6.1.4.1.13858.8.5 | not-accessible | This table describes battery temperature probes. | |
| STR sysAuxAlarmCustomName | 1.3.6.1.4.1.13858.8.5.1.3 | DisplayString | read-write | A string identifying probe location. |
| STR sysAuxAlarmDefaultName | 1.3.6.1.4.1.13858.8.5.1.2 | DisplayString | read-only | A string identifying probe location. |
| INT sysAuxAlarmIndex | 1.3.6.1.4.1.13858.8.5.1.1 | INTEGER | read-only | Index into temperature table |
| INT sysAuxAlarmOperStatus | 1.3.6.1.4.1.13858.8.5.1.7 | INTEGER | read-only | Indicates current alarm status |
| INT sysAuxAlarmPolarity | 1.3.6.1.4.1.13858.8.5.1.6 | INTEGER | read-write | Current temperature as recorded by the probe. |
| INT sysAuxAlarmSeverity | 1.3.6.1.4.1.13858.8.5.1.4 | INTEGER | read-write | Aux Alarm Severity |
| STR sysAuxAlarmToRelayMapping | 1.3.6.1.4.1.13858.8.5.1.5 | DisplayString | read-write | No additional mapping = 0 Map to Relay A = 1 Map to Relay B = 2 Map to Relay C = 4 Map to Relay D = 8 Map to Relay E = 16 Map to Relay F = 32 Map to Relay A and B = (1 + 2) and so on The major/minor classification of alarms automatically associates it with Major/Minor relay. Assigning a null mapping here does not override sysRelayAlarmSeverity for the alarm. It should be used to define mapping to additional relays. |
| INT sysRelayAlarmSeverity | 1.3.6.1.4.1.13858.8.3.1.4 | INTEGER | read-write | Current temperature as recorded by the probe. |
| sysRelayConfigEntry | 1.3.6.1.4.1.13858.8.3.1 | not-accessible | An entry containing information applicable to a particular temperature probe. | |
| sysRelayConfigTable | 1.3.6.1.4.1.13858.8.3 | not-accessible | This table describes battery temperature probes. | |
| STR sysRelayCustomName | 1.3.6.1.4.1.13858.8.3.1.3 | DisplayString | read-write | A string identifying probe location. |
| STR sysRelayDefaultName | 1.3.6.1.4.1.13858.8.3.1.2 | DisplayString | read-only | A string identifying probe location. |
| INT sysRelayIndex | 1.3.6.1.4.1.13858.8.3.1.1 | INTEGER | read-only | Index into temperature table |
| thermalProbeEntry | 1.3.6.1.4.1.13858.7.1.15.1 | not-accessible | An entry containing information applicable to a particular temperature probe. | |
| INT thermalProbeState | 1.3.6.1.4.1.13858.7.1.15.1.1 | INTEGER | read-only | State of thermal probe. |
| thermalProbeTable | 1.3.6.1.4.1.13858.7.1.15 | not-accessible | This table describes battery temperature probes. | |
| OID vpwrAlarmDescr | 1.3.6.1.4.1.13858.8.2.1.2 | AutonomousType | read-only | A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition. |
| vpwrAlarmEntry | 1.3.6.1.4.1.13858.8.2.1 | not-accessible | An entry containing information applicable to a particular alarm. | |
| NUM vpwrAlarmIndex | 1.3.6.1.4.1.13858.8.2.1.1 | PositiveInteger | read-only | Identifies the alarm associated with the module. It is unique on per module type basis. For example, multiple rectifiers can have the same alarm and therefore same vpwrAlarmIndex active at any one time. |
| G32 vpwrAlarmsPresent | 1.3.6.1.4.1.13858.8.1 | Gauge32 | read-only | The present number of active alarm conditions. |
| vpwrAlarmTable | 1.3.6.1.4.1.13858.8.2 | not-accessible | A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The vpwrAlarmIndex, for each type of module starts at 1 and is limited by the total number of alarams that can be generated by the module. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), vpwrAlarmDescr, to allow a single table to reflect alarms for different type of modules. The number of rows in the table at any given time is reflected by the value of vpwrAlarmsPresent. | |
| TIM vpwrAlarmTime | 1.3.6.1.4.1.13858.8.2.1.3 | TimeStamp | read-only | The value of sysUpTime when the alarm condition was detected. |
| vpwrBatteryBoostGroup | 1.3.6.1.4.1.13858.7.3 | |||
| vpwrBatteryCurrentGroup | 1.3.6.1.4.1.13858.7.2 | |||
| INT vpwrBatteryCurrentLimitAdminState | 1.3.6.1.4.1.13858.7.2.1 | INTEGER | read-write | This parameter allows enabling or disabling battery current limit. |
| vpwrBatteryDischargeTestGroup | 1.3.6.1.4.1.13858.7.4 | |||
| INT vpwrBatteryTemp | 1.3.6.1.4.1.13858.7.1.1.1.3 | INTEGER | read-only | Current temperature as recorded by the probe. |
| vpwrBatteryTempEntry | 1.3.6.1.4.1.13858.7.1.1.1 | not-accessible | An entry containing information applicable to a particular temperature probe. | |
| vpwrBatteryTempGroup | 1.3.6.1.4.1.13858.7.1 | |||
| INT vpwrBatteryTempIndex | 1.3.6.1.4.1.13858.7.1.1.1.1 | INTEGER | read-only | Index into temperature table |
| INT vpwrBatteryTempLThreshold | 1.3.6.1.4.1.13858.7.1.2 | INTEGER | read-write | Temperature value at which a clear trap would be sent. All three battery temperature must be at or below this value to trigger this trap. |
| STR vpwrBatteryTempName | 1.3.6.1.4.1.13858.7.1.1.1.2 | DisplayString | read-write | A string identifying probe location. |
| vpwrBatteryTempTable | 1.3.6.1.4.1.13858.7.1.1 | not-accessible | This table describes battery temperature probes. | |
| INT vpwrBatteryTempUThreshold | 1.3.6.1.4.1.13858.7.1.3 | INTEGER | read-write | Temperature value at which a set trap would be sent. Any one of the three battery temperatures at or exceeding this limit would trigger the trap. |
| INT vpwrBattetyCurrentLimitValue | 1.3.6.1.4.1.13858.7.2.2 | INTEGER | read-write | |
| INT vpwrBattetyCurrentValue | 1.3.6.1.4.1.13858.7.2.3 | INTEGER | read-only | |
| INT vpwrBayctrlCapacity | 1.3.6.1.4.1.13858.2.5.1.1.5 | INTEGER | read-only | This is the overall Capacity of the bay and is for reference only. |
| INT vpwrBayctrlCurrent | 1.3.6.1.4.1.13858.2.5.1.1.3 | INTEGER | read-only | This is the total output Current of the bay |
| STR vpwrBayctrlFwVersion | 1.3.6.1.4.1.13858.6.3.1.3 | DisplayString | read-only | Firmware version of the bay controller. |
| vpwrBayctrlIdentEntry | 1.3.6.1.4.1.13858.2.5.1.1 | not-accessible | An entry containing information applicable to a particular bay controller making up the system. | |
| vpwrBayctrlIdentTable | 1.3.6.1.4.1.13858.2.5.1 | not-accessible | This table describes bay controllers that make up the system. | |
| NUM vpwrBayctrlIndex | 1.3.6.1.4.1.13858.2.5.1.1.1 | PositiveInteger | read-only | Identifies bay number that this module belongs to. The possible values are 0 through 15, starting from the top. |
| STR vpwrBayctrlModelNumber | 1.3.6.1.4.1.13858.6.3.1.2 | DisplayString | read-only | Model Number of the bay controller. |
| vpwrBayctrlModuleIdentEntry | 1.3.6.1.4.1.13858.6.3.1 | not-accessible | An entry containing information applicable to a particular bay controller. | |
| vpwrBayctrlModuleIdentTable | 1.3.6.1.4.1.13858.6.3 | not-accessible | This table describes bay controllers that make up the sysetm. | |
| OID vpwrBayctrlOID | 1.3.6.1.4.1.13858.2.5.1.1.2 | OBJECT IDENTIFIER | read-only | It indicates the type of the module by specifiying its OID |
| C32 vpwrBayctrlOperHours | 1.3.6.1.4.1.13858.6.3.1.5 | Counter32 | read-only | Cumulative Operating Hours. |
| INT vpwrBayctrlOperStatus | 1.3.6.1.4.1.13858.2.5.1.1.4 | INTEGER | read-only | This object indicates over all status of the bay |
| STR vpwrBayctrlSerialNumber | 1.3.6.1.4.1.13858.6.3.1.1 | DisplayString | read-only | Serial Number of the bay controller |
| STR vpwrBayctrlTestDate | 1.3.6.1.4.1.13858.6.3.1.4 | DisplayString | read-only | Date when the bayctrl was last tested. |
| NUM vpwrBayIndex | 1.3.6.1.4.1.13858.2.1.6.1.1 | PositiveInteger | read-only | Identifies Bay number that this module belongs to. The possible values are 1 through 16 limited by vpwrSystemShelfCapacity. |
| INT vpwrBDTAbortVoltage | 1.3.6.1.4.1.13858.7.4.4 | INTEGER | read-write | |
| INT vpwrBDTAdminState | 1.3.6.1.4.1.13858.7.4.1 | INTEGER | read-write | Enable /Disable Battery Discharge Test execution. |
| INT vpwrBDTAlarmCoefficient | 1.3.6.1.4.1.13858.7.4.5 | INTEGER | read-write | |
| INT vpwrBDTAlarmVoltage | 1.3.6.1.4.1.13858.7.4.3 | INTEGER | read-write | |
| INT vpwrBDTClearAlarm | 1.3.6.1.4.1.13858.7.4.7 | INTEGER | read-write | Clears any active bdt alarm. |
| INT vpwrBDTDuration | 1.3.6.1.4.1.13858.7.4.2 | INTEGER | read-write | |
| INT vpwrBDTOperState | 1.3.6.1.4.1.13858.7.4.6 | INTEGER | read-write | Start/Stop Battery Discharge Test execution. |
| INT vpwrBoostAdminState | 1.3.6.1.4.1.13858.7.3.1 | INTEGER | read-write | This parameter allows enabling or disabling boost. |
| INT vpwrBoostDuration | 1.3.6.1.4.1.13858.7.3.3 | INTEGER | read-write | |
| INT vpwrBoostOperState | 1.3.6.1.4.1.13858.7.3.4 | INTEGER | read-write | This parameter allows starting or stoping boost if it is enabled. |
| INT vpwrBoostVoltage | 1.3.6.1.4.1.13858.7.3.2 | INTEGER | read-write | |
| vpwrDcAcInverterAlarmGroup | 1.3.6.1.4.1.13858.14.2 | |||
| vpwrDcAcInverterConfigGroup | 1.3.6.1.4.1.13858.14.1 | |||
| vpwrDcAcInverterTestGroup | 1.3.6.1.4.1.13858.14.3 | |||
| vpwrDcDcConverterAlarmGroup | 1.3.6.1.4.1.13858.13.2 | |||
| vpwrDcDcConverterConfigGroup | 1.3.6.1.4.1.13858.13.1 | |||
| vpwrDcDcConverterTestGroup | 1.3.6.1.4.1.13858.13.3 | |||
| vpwrDcPowerAlarmGroup | 1.3.6.1.4.1.13858.8 | |||
| vpwrDcPowerBatteryGroup | 1.3.6.1.4.1.13858.7 | |||
| vpwrDcPowerBayController | 1.3.6.1.4.1.13858.15 | |||
| vpwrDcPowerDcAcInverter | 1.3.6.1.4.1.13858.14 | |||
| vpwrDcPowerDcDcConverter | 1.3.6.1.4.1.13858.13 | |||
| vpwrDcPowerDist | 1.3.6.1.4.1.13858.17 | |||
| vpwrDcPowerIoModule | 1.3.6.1.4.1.13858.16 | |||
| vpwrDcPowerLvd | 1.3.6.1.4.1.13858.4 | |||
| vpwrDcPowerMgt | 1.3.6.1.4.1.13858 | MIB Version 0.8 Need description here. History Add table to retrieve module inventory info MIB Version 0.7 Dec 1, 05 Fixed HP Openview error Fixed warnings generated by MG-SOFT Add table to retrieve rectifier inventory info MIB Version 0.6 Feb 10, 2004 Added additional traps. Defined Ringers and other modules. Feb 08, 2003 Changed vpwrTrapDestinationTable to vpwrTrapTable Corrected entry for vpwrTrapTable to be VpwrTrapTableEntry This fixes errors generated by MG-SOFT mib compiler. Oct 30, 2002 initial release - version 0.4 | ||
| vpwrDcPowerModuleIdent | 1.3.6.1.4.1.13858.6 | |||
| vpwrDcPowerProducts | 1.3.6.1.4.1.13858.1 | |||
| vpwrDcPowerRectifier | 1.3.6.1.4.1.13858.3 | |||
| vpwrDcPowerRinger | 1.3.6.1.4.1.13858.12 | |||
| vpwrDcPowerSnmpConfig | 1.3.6.1.4.1.13858.9 | |||
| vpwrDcPowerSystem | 1.3.6.1.4.1.13858.2 | |||
| vpwrDcPowerTest | 1.3.6.1.4.1.13858.5 | |||
| vpwrDcPowerTraps | 1.3.6.1.4.1.13858.10 | |||
| vpwrDcPowerTrapsMsgString | 1.3.6.1.4.1.13858.11 | |||
| vpwrDcPowerTrio | 1.3.6.1.4.1.13858.18 | |||
| STR vpwrIdentAgentSoftwareVersion | 1.3.6.1.4.1.13858.2.1.4 | DisplayString | read-only | The SNMP agent software version. This variable may or may not have the same value as vpwrIdentControllerFirmwareVersion. |
| STR vpwrIdentControllerVersion | 1.3.6.1.4.1.13858.2.1.3 | DisplayString | read-only | The hardware/firmware version(s). This variable may or may not have the same value as vpwrIdentAgentSoftwareVersion. |
| STR vpwrIdentManufacturer | 1.3.6.1.4.1.13858.2.1.1 | DisplayString | read-only | The name of the DC Power manufacturer. |
| STR vpwrIdentModel | 1.3.6.1.4.1.13858.2.1.2 | DisplayString | read-only | The DC Power Model designation. |
| STR vpwrIdentName | 1.3.6.1.4.1.13858.2.1.5 | DisplayString | read-write | A string identifying the system. This object should be set by the administrator. |
| vpwrIoModuleAlarmGroup | 1.3.6.1.4.1.13858.16.2 | |||
| vpwrIoModuleConfigGroup | 1.3.6.1.4.1.13858.16.1 | |||
| vpwrIoModuleTestGroup | 1.3.6.1.4.1.13858.16.3 | |||
| vpwrLvdAlarmCBOpen | 1.3.6.1.4.1.13858.4.2.2 | Circuit Breaker open | ||
| vpwrLvdAlarmContactorOpen | 1.3.6.1.4.1.13858.4.2.1 | Contactor open | ||
| vpwrLvdAlarmGroup | 1.3.6.1.4.1.13858.4.2 | |||
| vpwrLvdAlarmWarning | 1.3.6.1.4.1.13858.4.2.4 | Plant Voltage below warning threshold | ||
| vpwrLvdConfigGroup | 1.3.6.1.4.1.13858.4.1 | |||
| vpwrLvdContactorConfigEntry | 1.3.6.1.4.1.13858.4.1.5.1 | not-accessible | An entry containing information applicable to a particular module making up the system. | |
| vpwrLvdContactorConfigTable | 1.3.6.1.4.1.13858.4.1.5 | not-accessible | This table describes shelves and modules that make up the sysetm. | |
| NUM vpwrLvdContactorDisconnectSetpoint | 1.3.6.1.4.1.13858.4.1.5.1.3 | PositiveInteger | read-write | LVD disconnect voltage setpoint. |
| NUM vpwrLvdContactorIndex | 1.3.6.1.4.1.13858.4.1.5.1.1 | PositiveInteger | read-only | contactor index |
| NUM vpwrLvdContactorReconnectDelayTimer | 1.3.6.1.4.1.13858.4.1.5.1.5 | PositiveInteger | read-write | The delay time, in seconds, before LVD is reconnected |
| NUM vpwrLvdContactorReconnectSetpoint | 1.3.6.1.4.1.13858.4.1.5.1.4 | PositiveInteger | read-write | LVD Reconnect voltage setpoint. |
| INT vpwrLvdContactorState | 1.3.6.1.4.1.13858.4.1.5.1.6 | INTEGER | read-write | The delay time, in seconds, before LVD is reconnected |
| NUM vpwrLvdContactorWarningSetpoint | 1.3.6.1.4.1.13858.4.1.5.1.2 | PositiveInteger | read-write | LVD Warning voltage setpoint. |
| INT vpwrLvdDisconnectSetpoint | 1.3.6.1.4.1.13858.4.1.2 | INTEGER | read-write | LVD disconnect voltage setpoint. |
| INT vpwrLvdReconnectDelayTimer | 1.3.6.1.4.1.13858.4.1.4 | INTEGER | read-write | The delay time, in seconds, before LVD is reconnected |
| INT vpwrLvdReconnectSetpoint | 1.3.6.1.4.1.13858.4.1.3 | INTEGER | read-write | LVD Reconnect voltage setpoint. |
| vpwrLvdTestGroup | 1.3.6.1.4.1.13858.4.3 | |||
| INT vpwrLvdWarningSetpoint | 1.3.6.1.4.1.13858.4.1.1 | INTEGER | read-write | LVD Warning voltage setpoint. |
| INT vpwrModuleCapacity | 1.3.6.1.4.1.13858.2.1.6.1.6 | INTEGER | read-only | The meaning of this object depends upon the module type which is indicated by vpwrModuleOID as follows - Capacity for Rectifier module. - Not Applicable for LVD module |
| INT vpwrModuleCurrent | 1.3.6.1.4.1.13858.2.1.6.1.4 | INTEGER | read-only | The meaning of this object depends upon the module type which is indicated by vpwrModuleOID as follows - Current for Rectifier module. - Not Applicable for LVD module |
| STR vpwrModuleFwVersion | 1.3.6.1.4.1.13858.6.1.1.3 | DisplayString | read-only | Firmware version of the module. |
| vpwrModuleIdentEntry | 1.3.6.1.4.1.13858.6.1.1 | not-accessible | An entry containing information applicable to a particular Module. | |
| vpwrModuleIdentTable | 1.3.6.1.4.1.13858.6.1 | not-accessible | This table describes shelves and modules that make up the sysetm. | |
| NUM vpwrModuleIndex | 1.3.6.1.4.1.13858.2.1.6.1.2 | PositiveInteger | read-only | This object identifies the module by its position in the shelf. Module numbering is left to right starting with module 1. So, the module in the first slot has an index of 1, the next module is 2 and so on. |
| STR vpwrModuleModelNumber | 1.3.6.1.4.1.13858.6.1.1.2 | DisplayString | read-only | Model Number of the module. |
| OID vpwrModuleOID | 1.3.6.1.4.1.13858.2.1.6.1.3 | OBJECT IDENTIFIER | read-only | It indicates the type of the module by specifiying its OID |
| C32 vpwrModuleOperHoursEx | 1.3.6.1.4.1.13858.6.1.1.5 | Counter32 | read-only | Cumulative Operating Hours. |
| INT vpwrModuleOperStatus | 1.3.6.1.4.1.13858.2.1.6.1.5 | INTEGER | read-only | This object indicates current over all status of the module. |
| STR vpwrModuleSerialNumber | 1.3.6.1.4.1.13858.6.1.1.1 | DisplayString | read-only | Serial Number of the module |
| STR vpwrModuleTestDate | 1.3.6.1.4.1.13858.6.1.1.4 | DisplayString | read-only | Date when the module was last tested. |
| NUM vpwrPanelBayIndex | 1.3.6.1.4.1.13858.2.4.1.1.1 | PositiveInteger | read-only | Identifies bay number that this module belongs to. The possible values are 1 through 16, starting from the top. |
| vpwrPanelIdentEntry | 1.3.6.1.4.1.13858.2.4.1.1 | not-accessible | An entry containing information applicable to a particular panel making up the system. | |
| vpwrPanelIdentTable | 1.3.6.1.4.1.13858.2.4.1 | not-accessible | This table describes shelves and modules that make up the panels. | |
| INT vpwrPanelModuleCapacity | 1.3.6.1.4.1.13858.2.4.1.1.6 | INTEGER | read-only | This is the overall Capacity of the module and is for reference only. |
| INT vpwrPanelModuleCurrent | 1.3.6.1.4.1.13858.2.4.1.1.4 | INTEGER | read-only | This is the Current of the first shunt of the module. |
| STR vpwrPanelModuleFwVersion | 1.3.6.1.4.1.13858.6.2.1.3 | DisplayString | read-only | Firmware version of the module. |
| vpwrPanelModuleIdentEntry | 1.3.6.1.4.1.13858.6.2.1 | not-accessible | An entry containing information applicable to a particular alarm. | |
| vpwrPanelModuleIdentTable | 1.3.6.1.4.1.13858.6.2 | not-accessible | This table describes shelves and modules that make up the sysetm. | |
| NUM vpwrPanelModuleIndex | 1.3.6.1.4.1.13858.2.4.1.1.2 | PositiveInteger | read-only | This object identifies the module within the panel. The orentation of modules within the panel is mappable. |
| STR vpwrPanelModuleModelNumber | 1.3.6.1.4.1.13858.6.2.1.2 | DisplayString | read-only | Model Number of the module. |
| OID vpwrPanelModuleOID | 1.3.6.1.4.1.13858.2.4.1.1.3 | OBJECT IDENTIFIER | read-only | It indicates the type of the module by specifiying its OID |
| C32 vpwrPanelModuleOperHours | 1.3.6.1.4.1.13858.6.2.1.5 | Counter32 | read-only | Cumulative Operating Hours. |
| INT vpwrPanelModuleOperStatus | 1.3.6.1.4.1.13858.2.4.1.1.5 | INTEGER | read-only | This object indicates over all status of the module. |
| STR vpwrPanelModuleSerialNumber | 1.3.6.1.4.1.13858.6.2.1.1 | DisplayString | read-only | Serial Number of the module |
| STR vpwrPanelModuleTestDate | 1.3.6.1.4.1.13858.6.2.1.4 | DisplayString | read-only | Date when the module was last tested. |
| STR vpwrReadCommunityString | 1.3.6.1.4.1.13858.9.2 | DisplayString | read-write | This allows setting password to be able to do Get operations |
| vpwrRectAlarmACFail | 1.3.6.1.4.1.13858.3.2.3 | |||
| vpwrRectAlarmAmbTemp | 1.3.6.1.4.1.13858.3.2.6 | |||
| vpwrRectAlarmBoostComm | 1.3.6.1.4.1.13858.3.2.16 | |||
| vpwrRectAlarmBoostFail | 1.3.6.1.4.1.13858.3.2.2 | |||
| vpwrRectAlarmDCEnable | 1.3.6.1.4.1.13858.3.2.12 | |||
| vpwrRectAlarmDCFail | 1.3.6.1.4.1.13858.3.2.1 | |||
| vpwrRectAlarmFanFail | 1.3.6.1.4.1.13858.3.2.5 | |||
| vpwrRectAlarmHVSD | 1.3.6.1.4.1.13858.3.2.4 | |||
| vpwrRectAlarmIntTemp | 1.3.6.1.4.1.13858.3.2.7 | |||
| vpwrRectAlarmIShare | 1.3.6.1.4.1.13858.3.2.8 | |||
| vpwrRectAlarmLowVoltage | 1.3.6.1.4.1.13858.3.2.10 | |||
| vpwrRectAlarmModDisableShutdown | 1.3.6.1.4.1.13858.3.2.14 | |||
| vpwrRectAlarmRemoteShutdown | 1.3.6.1.4.1.13858.3.2.13 | |||
| vpwrRectAlarmReserved | 1.3.6.1.4.1.13858.3.2.11 | |||
| vpwrRectAlarmShortPinShutdown | 1.3.6.1.4.1.13858.3.2.15 | |||
| vpwrRectAlarmUV | 1.3.6.1.4.1.13858.3.2.9 | |||
| vpwrRectifierAlarmGroup | 1.3.6.1.4.1.13858.3.2 | |||
| vpwrRectifierConfigGroup | 1.3.6.1.4.1.13858.3.1 | |||
| INT vpwrRectifierCurrentLimit | 1.3.6.1.4.1.13858.3.1.4 | INTEGER | read-write | Rectifier current limit setpoint |
| INT vpwrRectifierCurrentLimitAdminState | 1.3.6.1.4.1.13858.3.1.3 | INTEGER | read-write | This parameter allows enabling or disabling boost. |
| INT vpwrRectifierFVSetpoint | 1.3.6.1.4.1.13858.3.1.1 | INTEGER | read-write | System Float Voltage setting |
| INT vpwrRectifierHVSDSetpoint | 1.3.6.1.4.1.13858.3.1.2 | INTEGER | read-write | System High Voltage Shutdown voltage setting |
| vpwrRectifierTestGroup | 1.3.6.1.4.1.13858.3.3 | |||
| vpwrRingerAlarmaAFailed | 1.3.6.1.4.1.13858.12.2.1 | Ringer A Failed | ||
| vpwrRingerAlarmaBFailed | 1.3.6.1.4.1.13858.12.2.4 | Ringer A Failed | ||
| vpwrRingerAlarmAOCurrent | 1.3.6.1.4.1.13858.12.2.3 | Ringer A Over-Current protection | ||
| vpwrRingerAlarmAOTemp | 1.3.6.1.4.1.13858.12.2.2 | Ringer A Heatsink Over-Temperature | ||
| vpwrRingerAlarmBOverCurrent | 1.3.6.1.4.1.13858.12.2.6 | Ringer A Over-Current protection | ||
| vpwrRingerAlarmBOverTemp | 1.3.6.1.4.1.13858.12.2.5 | Ringer A Heatsink Over-Temperature | ||
| vpwrRingerAlarmGroup | 1.3.6.1.4.1.13858.12.2 | |||
| vpwrRingerConfigGroup | 1.3.6.1.4.1.13858.12.1 | |||
| INT vpwrRingerIndex | 1.3.6.1.4.1.13858.12.1.1.1.1 | INTEGER | read-only | This parameter allows selecting ringer A or Ringer B as the active ringer. |
| G32 vpwrRingerNumberPresent | 1.3.6.1.4.1.13858.12.1.2 | Gauge32 | read-only | The present number of active alarm conditions. |
| INT vpwrRingerParameterAcVoltage | 1.3.6.1.4.1.13858.12.1.1.1.3 | INTEGER | read-write | |
| INT vpwrRingerParameterAdminState | 1.3.6.1.4.1.13858.12.1.1.1.2 | INTEGER | read-write | This parameter allows selecting ringer A or Ringer B as the active ringer. |
| INT vpwrRingerParameterDcVoltage | 1.3.6.1.4.1.13858.12.1.1.1.4 | INTEGER | read-write | |
| vpwrRingerParameterEntry | 1.3.6.1.4.1.13858.12.1.1.1 | not-accessible | An entry containing information applicable to a particular alarm. | |
| INT vpwrRingerParameterFrequency | 1.3.6.1.4.1.13858.12.1.1.1.5 | INTEGER | read-write | |
| vpwrRingerParameterTable | 1.3.6.1.4.1.13858.12.1.1 | not-accessible | A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The vpwrAlarmIndex, for each type of module starts at 1 and is limited by the total number of alarams that can be generated by the module. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), vpwrAlarmDescr, to allow a single table to reflect alarms for different type of modules. The number of rows in the table at any given time is reflected by the value of vpwrAlarmsPresent. | |
| vpwrRingerTestGroup | 1.3.6.1.4.1.13858.12.3 | |||
| vpwrSystemBayctrlIdentGroup | 1.3.6.1.4.1.13858.2.5 | |||
| INT vpwrSystemBDAlarmSetpoint | 1.3.6.1.4.1.13858.2.2.7 | INTEGER | read-write | System Battery Discharge voltage setting. |
| vpwrSystemConfigGroup | 1.3.6.1.4.1.13858.2.2 | |||
| INT vpwrSystemControllerState | 1.3.6.1.4.1.13858.2.3.4 | INTEGER | read-only | Current System state as shown on the enhanced display. |
| INT vpwrSystemCurrent | 1.3.6.1.4.1.13858.2.3.3 | INTEGER | read-only | The current system current. |
| INT vpwrSystemHVAlarmSetpoint | 1.3.6.1.4.1.13858.2.2.6 | INTEGER | read-write | System High voltage alarm voltage setting. |
| vpwrSystemIdentEntry | 1.3.6.1.4.1.13858.2.1.6.1 | not-accessible | An entry containing information applicable to a particular alarm. | |
| vpwrSystemIdentGroup | 1.3.6.1.4.1.13858.2.1 | |||
| vpwrSystemIdentTable | 1.3.6.1.4.1.13858.2.1.6 | not-accessible | This table describes shelves and modules that make up the sysetm. | |
| INT vpwrSystemInternalTemperature | 1.3.6.1.4.1.13858.2.3.5 | INTEGER | read-only | The current controller internal temperature. |
| INT vpwrSystemInternalTempLThreshold | 1.3.6.1.4.1.13858.2.2.8 | INTEGER | read-write | Temperature value at which temperature compensation inactive (clear) trap would be sent if temperature compensation was active when this value is reached. |
| INT vpwrSystemInternalTempUThreshold | 1.3.6.1.4.1.13858.2.2.9 | INTEGER | read-write | Temperature value at which temperature compensation active (set) trap would be sent. |
| vpwrSystemPanelIdentGroup | 1.3.6.1.4.1.13858.2.4 | |||
| vpwrSystemParameterGroup | 1.3.6.1.4.1.13858.2.3 | |||
| INT vpwrSystemShelfCapacity | 1.3.6.1.4.1.13858.2.3.1 | INTEGER | read-only | It describes the maximum number of shelves that can/are controlled by the controller. Each shelf is uniquely numbered in the range from 1 to vpwrShelfCapacity. |
| INT vpwrSystemTempCompensation | 1.3.6.1.4.1.13858.2.2.1 | INTEGER | read-write | This parameter enables/disables temperature compensation. |
| INT vpwrSystemTempCompensationSlope | 1.3.6.1.4.1.13858.2.2.4 | INTEGER | read-write | The rate at which float voltage is changed, within the specified limits, when temperature compensation is active. |
| INT vpwrSystemTempCompensationState | 1.3.6.1.4.1.13858.2.3.6 | INTEGER | read-only | Active or Inactive. Applicable only if temperature compensation is enabled. This means that the controller is temperature compensating the float voltage. |
| INT vpwrSystemTempCompStartTemperature | 1.3.6.1.4.1.13858.2.2.2 | INTEGER | read-write | The temperature at which temperature compensation becomes active. |
| INT vpwrSystemTempCompStopVoltage | 1.3.6.1.4.1.13858.2.2.3 | INTEGER | read-write | When temperature compensation is active, vpwrSystemTempCompStopVoltage is the limit to which float voltage will be reduced. For example, to set this voltage to 51.75 volts enter a value of 5175. |
| INT vpwrSystemThermalSenseType | 1.3.6.1.4.1.13858.2.2.5 | INTEGER | read-write | This parameter selects the temperature sensing point for temperature compensation (in)activation. |
| INT vpwrSystemType | 1.3.6.1.4.1.13858.2.3.7 | INTEGER | read-only | This parameter describes the type of the system being managed. This object is set by Valere Power Inc. |
| INT vpwrSystemVoltage | 1.3.6.1.4.1.13858.2.3.2 | INTEGER | read-only | The current system voltage. |
| NTF vpwrTrapACFAlarm | 1.3.6.1.4.1.13858.10.0.3 | AC Fail Alarm | ||
| NTF vpwrTrapAdminPwdChange | 1.3.6.1.4.1.13858.10.0.29 | Config change submitted with invalid access. | ||
| NTF vpwrTrapAuxAlarm | 1.3.6.1.4.1.13858.10.0.10 | Auxiliary System Alarm | ||
| NTF vpwrTrapBatteryDischargeTestAlarm | 1.3.6.1.4.1.13858.10.0.39 | System Voltage dropped to BDT Alarm Setpoint. | ||
| NTF vpwrTrapBatteryRechgIlimitFailAlarm | 1.3.6.1.4.1.13858.10.0.53 | Battery Recharge Current Limit Fail. | ||
| NTF vpwrTrapBatteryTempAlarmCleared | 1.3.6.1.4.1.13858.10.0.25 | All Battery Temperatures within limits. | ||
| NTF vpwrTrapBatteryTempAlarmSet | 1.3.6.1.4.1.13858.10.0.24 | At least one Battery Temperature exceeded upper threshold. | ||
| NTF vpwrTrapBDAlarm | 1.3.6.1.4.1.13858.10.0.6 | Battery on Discharge Alarm | ||
| NTF vpwrTrapCfgChange | 1.3.6.1.4.1.13858.10.0.31 | Config change submitted. | ||
| NTF vpwrTrapClearEventHistory | 1.3.6.1.4.1.13858.10.0.32 | Clear Event history buffer clear request. | ||
| STR vpwrTrapCommunityString | 1.3.6.1.4.1.13858.9.4 | DisplayString | read-write | This allows setting community string required for the trap to be accepted at the destination. |
| NTF vpwrTrapConfigErrorAlarm | 1.3.6.1.4.1.13858.10.0.50 | Configuration Error. | ||
| NTF vpwrTrapConverterAlarm | 1.3.6.1.4.1.13858.10.0.47 | Single Converter Fail Alarm. | ||
| NTF vpwrTrapConverterInputFailAlarm | 1.3.6.1.4.1.13858.10.0.52 | Converter Input Fail Alarm. | ||
| INT vpwrTrapCriticality | 1.3.6.1.4.1.13858.9.1.1.3 | INTEGER | read-write | Criticality of traps sent to this IP Address |
| NTF vpwrTrapDisplayFirmwareMismatchAlarm | 1.3.6.1.4.1.13858.10.0.51 | Display Firmware Mismatch. | ||
| NTF vpwrTrapDistAlarm | 1.3.6.1.4.1.13858.10.0.9 | Distribution Open Alarm | ||
| NTF vpwrTrapDistributionCommAlarm | 1.3.6.1.4.1.13858.10.0.46 | Distribution Communication Alarm. | ||
| vpwrTrapEntry | 1.3.6.1.4.1.13858.9.1.1 | not-accessible | An entry containing information applicable to a particular trap destination. | |
| IP vpwrTrapEventTimeStamp | 1.3.6.1.4.1.13858.11.3 | IpAddress | not-accessible | Place holder for time-stamp. |
| NTF vpwrTrapHVAlarm | 1.3.6.1.4.1.13858.10.0.4 | High Voltage Warning Alarm | ||
| NTF vpwrTrapHVSDAlarm | 1.3.6.1.4.1.13858.10.0.5 | High Voltage Shutdown Alarm | ||
| NTF vpwrTrapIllegalConfigSubmit | 1.3.6.1.4.1.13858.10.0.30 | Config change submitted with invalid access. | ||
| NTF vpwrTrapInternalTempAlarmCleared | 1.3.6.1.4.1.13858.10.0.23 | Internal Temperature within limits | ||
| NTF vpwrTrapInternalTempAlarmSet | 1.3.6.1.4.1.13858.10.0.22 | Internal Temperature upper threshold exceeded. | ||
| IP vpwrTrapIpAddress | 1.3.6.1.4.1.13858.9.1.1.2 | IpAddress | read-write | Trap destination IP Address |
| INT vpwrTrapIpIndex | 1.3.6.1.4.1.13858.9.1.1.1 | INTEGER | read-only | Trap Entry Index |
| NTF vpwrTrapIShareAlarm | 1.3.6.1.4.1.13858.10.0.12 | Rectifier Current Share Alarm | ||
| NTF vpwrTrapLoginFail | 1.3.6.1.4.1.13858.10.0.26 | Admin login failed due to wrong username/password. | ||
| NTF vpwrTrapLoginSuccess | 1.3.6.1.4.1.13858.10.0.27 | Admin login successful. | ||
| NTF vpwrTrapLogout | 1.3.6.1.4.1.13858.10.0.28 | Admin logout. | ||
| vpwrTrapLvdFuseOpen | 1.3.6.1.4.1.13858.4.2.3 | Fuse open | ||
| NTF vpwrTrapLVDOpenAlarm | 1.3.6.1.4.1.13858.10.0.8 | LVD Open Alarm | ||
| NTF vpwrTrapLVDWarningAlarm | 1.3.6.1.4.1.13858.10.0.7 | LVD Warning Alarm | ||
| NTF vpwrTrapModuleAlarm | 1.3.6.1.4.1.13858.10.0.36 | Module Alarm. | ||
| NTF vpwrTrapModuleCommAlarm | 1.3.6.1.4.1.13858.10.0.15 | Module Communication Alarm | ||
| NTF vpwrTrapModuleFailAlarm | 1.3.6.1.4.1.13858.10.0.13 | Single Rectifier Fail Alarm | ||
| NTF vpwrTrapModuleInserted | 1.3.6.1.4.1.13858.10.0.18 | A new module has been inserted into the system. | ||
| NTF vpwrTrapModuleRemoved | 1.3.6.1.4.1.13858.10.0.19 | A module has been removed from the system. | ||
| NTF vpwrTrapMultipleConvFailAlarm | 1.3.6.1.4.1.13858.10.0.48 | Multiple Converter Fail Alarm. | ||
| NTF vpwrTrapMultipleModuleFailAlarm | 1.3.6.1.4.1.13858.10.0.14 | Multiple Rectifier Fail Alarm | ||
| NTF vpwrTrapMultipleRingerAlarm | 1.3.6.1.4.1.13858.10.0.43 | Multiple Ringer Fail Alarm. | ||
| NTF vpwrTrapOIDChange | 1.3.6.1.4.1.13858.10.0.37 | Change in OID. | ||
| NTF vpwrTrapPowerMajorAlarm | 1.3.6.1.4.1.13858.10.0.1 | Major Alarm | ||
| NTF vpwrTrapPowerMinorAlarm | 1.3.6.1.4.1.13858.10.0.2 | Minor Alarm | ||
| NTF vpwrTrapRingerAAlarm | 1.3.6.1.4.1.13858.10.0.40 | Ringer A Fail Alarm. | ||
| NTF vpwrTrapRingerBAlarm | 1.3.6.1.4.1.13858.10.0.41 | Ringer B Fail Alarm. | ||
| NTF vpwrTrapRingerCommAlarm | 1.3.6.1.4.1.13858.10.0.45 | Ringer Communication Alarm. | ||
| NTF vpwrTrapSingleRingerAlarm | 1.3.6.1.4.1.13858.10.0.42 | Single Ringer Fail Alarm. | ||
| STR vpwrTrapsMsgString | 1.3.6.1.4.1.13858.11.1 | DisplayString | not-accessible | Place holder for trap notification message string |
| NTF vpwrTrapSwDownloadAndReboot | 1.3.6.1.4.1.13858.10.0.34 | System reboot due to software upgrade. | ||
| NTF vpwrTrapSwDownloadNoReboot | 1.3.6.1.4.1.13858.10.0.33 | System software upgrade without reboot. | ||
| NTF vpwrTrapSystemAlive | 1.3.6.1.4.1.13858.10.0.54 | Periodic Keepalive trap. | ||
| NTF vpwrTrapSystemClockChange | 1.3.6.1.4.1.13858.10.0.35 | System clock updated. | ||
| NTF vpwrTrapSystemOK | 1.3.6.1.4.1.13858.10.0.17 | SYSTEM OK - No Active Alarms | ||
| NTF vpwrTrapSystemOverTemperatureAlarm | 1.3.6.1.4.1.13858.10.0.16 | System Over Temperature Alarm | ||
| NTF vpwrTrapSystemRedundancyAlarm | 1.3.6.1.4.1.13858.10.0.11 | System Redundant Capacity Alarm | ||
| vpwrTrapTable | 1.3.6.1.4.1.13858.9.1 | not-accessible | A list of possible trap destinations depending upon the criticality of the trap. | |
| NTF vpwrTrapThermalCompActive | 1.3.6.1.4.1.13858.10.0.20 | Thermal compensation has become active. | ||
| NTF vpwrTrapThermalCompInactive | 1.3.6.1.4.1.13858.10.0.21 | Thermal compensation has been de-activated. | ||
| NTF vpwrTrapThermalProbeAlarm | 1.3.6.1.4.1.13858.10.0.44 | Thermal Probe Missing Alarm. | ||
| NTF vpwrTrapThermalRunaway | 1.3.6.1.4.1.13858.10.0.38 | Thermal Runaway Alarm. | ||
| NTF vpwrTrapUnmappedAddressAlarm | 1.3.6.1.4.1.13858.10.0.49 | Unmapped I2C Address. | ||
| IP vpwrTrapUserIpAddress | 1.3.6.1.4.1.13858.11.2 | IpAddress | not-accessible | Place holder for IP address of the user accessing the system |
| STR vpwrWriteCommunityString | 1.3.6.1.4.1.13858.9.3 | DisplayString | read-write | This allows setting password to be able to do Get and Set operations. The read-access is not allowed in the actual implementation. |
RFC description
Valere DC power management MIB for rectifiers, batteries, inverters, and power system monitoring in telecommunications infrastructure.
Start monitoring Valere DC power systems / rectifier cabinets, telecom power plant equipment (rectifier/battery alarm status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.