TPLINK-RIP-MIB

All MIBs › TPLINK-RIP-MIB

Organization: TPLINK

Last Updated: 2012-12-13

Category: IP Routing and Multicast

Description: Manages TP-Link switch RIP routing protocol version, timers, interface enablement, and redistribution.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TPLINK-RIP-MIB?

TPLINK-RIP-MIB is a TP-Link vendor-specific MIB for configuring the RIP (Routing Information Protocol) dynamic-routing feature on Layer-3-capable managed switches, covering protocol version, timer settings, per-interface enablement, and route redistribution. As a routing-protocol configuration MIB, its main monitoring value is confirming RIP is enabled on the correct interfaces with consistent timers, since a timer mismatch or unexpectedly disabled interface would explain missing or flapping routes. It implements the IETF RIP/RIPv2 standard (RFC 2453), complementing the standard RIP2-MIB in environments that lack it. It's deployed on TP-Link Layer-3 switches used as simple dynamic-routing gateways in small-to-medium enterprise networks. Engineers can download the TPLINK-RIP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TPLINK-RIP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

TP-Link Layer-3 managed switches/routers

Monitoring Examples

An administrator checks the per-interface RIP enable object and the configured RIP version (v1/v2) to confirm a routed VLAN interface is participating in RIP as expected, and reviews the update/invalid/garbage-collection timer objects to verify they match the rest of the RIP domain. A route-redistribution object left enabled unintentionally could explain static or connected routes unexpectedly appearing in neighboring routers' RIP tables.

What Can Be Monitored

RIP version configuration
per-interface RIP enable state
update/invalid/garbage-collection timers
route redistribution settings

Imported Objects

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From TPLINK-MIB

tplinkMgmt

OBJECT-IDENTITY

From TPLINK-TC-MIB

TPRowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
tplinkRipMIB	1.3.6.1.4.1.11863.6.40			Private MIB for RIP configuration.
tplinkRipMIBObjects	1.3.6.1.4.1.11863.6.40.1
tpRipBasicConfig	1.3.6.1.4.1.11863.6.40.1.1
INT tpRipProtocolCtrl	1.3.6.1.4.1.11863.6.40.1.1.1	INTEGER	read-write	Enable or disable the RIP function on the switch.
INT tpRipProtocolVersion	1.3.6.1.4.1.11863.6.40.1.1.2	INTEGER	read-write	Choose the global RIP version.
INT tpRipDistance	1.3.6.1.4.1.11863.6.40.1.1.3	INTEGER	read-write	Set the RIP router distance.
INT tpRipAutoSumm	1.3.6.1.4.1.11863.6.40.1.1.4	INTEGER	read-write	If you select enable groups of adjacent routes will be summarized into single entries.
INT tpRipDefaultMetric	1.3.6.1.4.1.11863.6.40.1.1.5	INTEGER	read-write	Set the default metric for redistributed routes.
INT tpRipRedistriStatic	1.3.6.1.4.1.11863.6.40.1.1.6	INTEGER	read-write	Choose to distribute Static router entries to RIP,the default is disable.
INT tpRipRedistriOspf	1.3.6.1.4.1.11863.6.40.1.1.7	INTEGER	read-write	Choose to distribute OSPF router entries to RIP,the default is disable..
INT tpRipRedistStaticMetric	1.3.6.1.4.1.11863.6.40.1.1.8	INTEGER	read-write	Set the metric for redistributed static routes.
INT tpRipRedistOspfMetric	1.3.6.1.4.1.11863.6.40.1.1.9	INTEGER	read-write	Set the metric for redistributed OSPF routes.
INT tpRipUpdateTimer	1.3.6.1.4.1.11863.6.40.1.1.10	INTEGER	read-write	The timer interval to generate a complete response to every neighboring gateway.
INT tpRipTimeOutTimer	1.3.6.1.4.1.11863.6.40.1.1.11	INTEGER	read-write	Upon expiration of the timeout, the route is no longer valid and setted to unreachable.
INT tpRipGarbageTimer	1.3.6.1.4.1.11863.6.40.1.1.12	INTEGER	read-write	Upon expiration of the garbage-collection timer, the route is finally removed from the tables.
tpRipNetworkConfig	1.3.6.1.4.1.11863.6.40.1.2
tpRipNetworkTable	1.3.6.1.4.1.11863.6.40.1.2.1		not-accessible	The list of rip network.
tpRipNetworkEntry	1.3.6.1.4.1.11863.6.40.1.2.1.1		not-accessible	RIP network entries.
IP tpRipNetworkAddress	1.3.6.1.4.1.11863.6.40.1.2.1.1.1	IpAddress	read-create	RIP network IP address.
TPR tpRipNetworkStatus	1.3.6.1.4.1.11863.6.40.1.2.1.1.2	TPRowStatus	read-create	The following values are states: these values may be used as follow: active(1),if the entry is being used. notInService(2),destory the entry. notReady(3),destory the entry. createAndGo(4),not being used createAndWait(5),creat a new entry destroy(6),destory the entry.
tpRipInterfaceConfig	1.3.6.1.4.1.11863.6.40.1.3
tpRipInterfaceTable	1.3.6.1.4.1.11863.6.40.1.3.1		not-accessible	The list of rip interfaces.
tpRipInterfaceEntry	1.3.6.1.4.1.11863.6.40.1.3.1.1		not-accessible	Config the RIP parameters of the interface.
OCT tpRipInterfaceID	1.3.6.1.4.1.11863.6.40.1.3.1.1.1	OCTET STRING	read-only	The interface IP address and subnet mask.
OCT tpRipInterfaceStatus	1.3.6.1.4.1.11863.6.40.1.3.1.1.2	OCTET STRING	read-only	The interface RIP status(up or down).
INT tpRipInterfaceSendVersion	1.3.6.1.4.1.11863.6.40.1.3.1.1.3	INTEGER	read-write	Select the version of RIP control packets sended from the interface.
INT tpRipInterfaceRecvVersion	1.3.6.1.4.1.11863.6.40.1.3.1.1.4	INTEGER	read-write	Select the version of RIP control packets received from the interface.
INT tpRipInterfaceRIPv2Broad	1.3.6.1.4.1.11863.6.40.1.3.1.1.5	INTEGER	read-write	Send RIP version 2 formatted packets via broadcast.
INT tpRipInterfaceAuthMode	1.3.6.1.4.1.11863.6.40.1.3.1.1.6	INTEGER	read-write	Select an authentication type.
INT tpRipInterfaceKeyID	1.3.6.1.4.1.11863.6.40.1.3.1.1.7	INTEGER	read-write	Enter the RIP Authentication Key ID for the specified interface.
OCT tpRipInterfaceKey	1.3.6.1.4.1.11863.6.40.1.3.1.1.8	OCTET STRING	read-write	Enter the RIP Authentication Key for the specified interface.
INT tpRipInterfaceSplitHorizon	1.3.6.1.4.1.11863.6.40.1.3.1.1.9	INTEGER	read-write	Enable or disable the split horizon.
INT tpRipInterfacePoisonReverse	1.3.6.1.4.1.11863.6.40.1.3.1.1.10	INTEGER	read-write	Enable or disable the poison reverse.
tpRipRouteItems	1.3.6.1.4.1.11863.6.40.1.4
tpRipRouteTable	1.3.6.1.4.1.11863.6.40.1.4.1		not-accessible	Display the route entries generated by RIP protocol.
tpRipRouteEntry	1.3.6.1.4.1.11863.6.40.1.4.1.1		not-accessible	RIP route entries.
OCT tpRipIpAddressMask	1.3.6.1.4.1.11863.6.40.1.4.1.1.1	OCTET STRING	read-only	The destination IP address and subnet mask.
IP tpRipGateway	1.3.6.1.4.1.11863.6.40.1.4.1.1.2	IpAddress	read-only	The gateway interface to send the data packet.
INT tpRipMetric	1.3.6.1.4.1.11863.6.40.1.4.1.1.3	INTEGER	read-only	The metric to reach the destination IP address.
OCT tpRipInterfaceName	1.3.6.1.4.1.11863.6.40.1.4.1.1.4	OCTET STRING	read-only	The gateway interface name.
INT tpRipTimers	1.3.6.1.4.1.11863.6.40.1.4.1.1.5	INTEGER	read-only	The time of the route entry.
tplinkRipNotifications	1.3.6.1.4.1.11863.6.40.2

RFC description

Configures RIP routing protocol version, distance, metrics, and network redistribution.

Start monitoring TP-Link managed switches/routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TPLINK-RIP-MIB

What Is TPLINK-RIP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description