TPLINK-PIM-MIB

All MIBs › TPLINK-PIM-MIB

Organization: TPLINK

Last Updated: 2012-12-13

Category: IP Routing and Multicast, Multicast Management

Description: Manages TP-Link switch Protocol Independent Multicast routing mode and interface configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TPLINK-PIM-MIB?

TPLINK-PIM-MIB is a TP-Link private MIB for configuring Protocol Independent Multicast (PIM) routing on their Layer 3 switches, controlling how multicast traffic is routed between subnets using either PIM sparse mode or dense mode. It exposes global and per-interface configuration for enabling PIM and selecting its operating mode. Its monitoring value is configuration/routing-protocol status - confirming PIM is enabled on the correct interfaces and operating in the intended mode - rather than hardware telemetry. It is a vendor implementation of the IETF PIM standard and typically interoperates with IGMP snooping (TPLINK-IGMPSNOOPING-MIB) for end-to-end multicast delivery. The TPLINK-PIM-MIB MIB is deployed on TP-Link Layer 3 managed switches/routers in networks distributing multicast traffic (e.g., IPTV, video conferencing) across multiple subnets.

IPNetwork Monitor allows you to monitor SNMP objects defined in TPLINK-PIM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

TP-Link Layer 3 managed switch/router

Monitoring Examples

Specific table/object names were not present in the provided sample, so a concrete polling example is not grounded in real identifiers; based on the module description, an administrator would check per-interface PIM enable status and configured mode (sparse/dense) to confirm multicast routing is active where expected, investigating a delivery failure by verifying PIM is actually enabled on the transit interfaces involved.

What Can Be Monitored

PIM enable/disable state per interface
PIM operating mode (sparse/dense)

Imported Objects

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From TPLINK-MIB

tplinkMgmt

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
tplinkPimMIB	1.3.6.1.4.1.11863.6.77			Private MIB for PIM configuration.
tplinkPimMIBObjects	1.3.6.1.4.1.11863.6.77.1
tpPim	1.3.6.1.4.1.11863.6.77.1.1
I32 tpSGExpiryTimer	1.3.6.1.4.1.11863.6.77.1.1.1	Integer32	read-write	Specify the expiry timer for the entry.
INT tpPimdataThresholdRate	1.3.6.1.4.1.11863.6.77.1.1.2	INTEGER	read-write	Select rate which the last-hop router will switch to a source-specific shortest path tree. Specify infinity if you want all sources for the specified group to use the shared tree, never switching to the source tree.The default is 0 kbps.
tpPimInterfaceTable	1.3.6.1.4.1.11863.6.77.1.1.3		not-accessible	The (conceptual) table listing the router's PIM interfaces. IGMP and PIM are enabled on all interfaces listed in this table.
tpPimInterfaceEntry	1.3.6.1.4.1.11863.6.77.1.1.3.1		not-accessible	An entry (conceptual row) in the pimInterfaceTable.
OCT tpPimInterface	1.3.6.1.4.1.11863.6.77.1.1.3.1.1	OCTET STRING	read-only	Display the interface which you can configure.
I32 tpPimInterfaceIndex	1.3.6.1.4.1.11863.6.77.1.1.3.1.2	Integer32	read-only	The Index value of this PIM interface.
INT tpPimInterfaceType	1.3.6.1.4.1.11863.6.77.1.1.3.1.3	INTEGER	read-only	The configured type of this interface.
IP tpPimInterfaceAddress	1.3.6.1.4.1.11863.6.77.1.1.3.1.4	IpAddress	read-only	The IP address of the PIM interface.
IP tpPimInterfaceNetMask	1.3.6.1.4.1.11863.6.77.1.1.3.1.5	IpAddress	read-only	The network mask for the IP address of the PIM interface.
INT tpPimInterfaceMode	1.3.6.1.4.1.11863.6.77.1.1.3.1.6	INTEGER	read-write	The configured mode of this PIM interface.
INT tpPimInterfaceDRPriority	1.3.6.1.4.1.11863.6.77.1.1.3.1.7	INTEGER	read-write	The Designated Router Priority value inserted into the DR Priority option on this interface.Numerically higher values for this object indicate higher priorities.
IP tpPimInterfaceDRAddress	1.3.6.1.4.1.11863.6.77.1.1.3.1.8	IpAddress	read-only	The Designated Router on this PIM interface. For point- to-point interfaces, this object has the value 0.0.0.0.
I32 tpPimInterfaceHelloInterval	1.3.6.1.4.1.11863.6.77.1.1.3.1.9	Integer32	read-write	The frequency at which PIM Hello messages are transmitted on this interface.
INT tpPimInterfaceBsrBorder	1.3.6.1.4.1.11863.6.77.1.1.3.1.10	INTEGER	read-write	The frequency at which PIM Hello messages are transmitted on this interface.
I32 tpPimInterfaceJoinPruneInterval	1.3.6.1.4.1.11863.6.77.1.1.3.1.11	Integer32	read-write	The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. This object corresponds to the 't_periodic' timer value defined in the PIM-SM specification [I-D.ietf-pim-sm-v2-new]. A value of 0 represents an 'infinite' interval, and indicates that periodic PIM Join/Prune messages should not be sent on this interface.
tpPimNeighborTable	1.3.6.1.4.1.11863.6.77.1.1.4		not-accessible	The (conceptual) table listing the router's PIM neighbors.
tpPimNeighborEntry	1.3.6.1.4.1.11863.6.77.1.1.4.1		not-accessible	An entry (conceptual row) in the pimNeighborTable.
OCT tpPimNeighborInterface	1.3.6.1.4.1.11863.6.77.1.1.4.1.1	OCTET STRING	read-only	The interface used to reach this PIM neighbor.
I32 tpPimNeighborInterfaceIndex	1.3.6.1.4.1.11863.6.77.1.1.4.1.2	Integer32	read-only	The value of ifIndex for the interface used to reach this PIM neighbor.
IP tpPimNeighborAddress	1.3.6.1.4.1.11863.6.77.1.1.4.1.3	IpAddress	read-only	The IP address of the PIM neighbor for which this entry contains information.
TIK tpPimNeighborUpTime	1.3.6.1.4.1.11863.6.77.1.1.4.1.4	TimeTicks	read-only	The time since this PIM neighbor (last) became a neighbor of the local router.
TIK tpPimNeighborExpiryTime	1.3.6.1.4.1.11863.6.77.1.1.4.1.5	TimeTicks	read-only	The minimum time remaining before this PIM neighbor will be aged out.
INT tpPimNeighborMode	1.3.6.1.4.1.11863.6.77.1.1.4.1.6	INTEGER	read-only	The active PIM mode of this neighbor. This object is deprecated for PIMv2 routers since all neighbors on the interface must be either dense or sparse as determined by the protocol running on the interface.
tpPimCandidateBSRSet	1.3.6.1.4.1.11863.6.77.1.1.5
OCT tpPimCBSRInterface	1.3.6.1.4.1.11863.6.77.1.1.5.1	OCTET STRING	read-only	Specify the interface of the BSR.
I32 tpPimCBSRInterfaceIndex	1.3.6.1.4.1.11863.6.77.1.1.5.2	Integer32	read-write	Specify the interface index of the BSR.
I32 tpPimCBSRHashMaskLength	1.3.6.1.4.1.11863.6.77.1.1.5.3	Integer32	read-write	Specify the hash mask length of the BSR. The default value is 30.
I32 tpPimCBSRPriority	1.3.6.1.4.1.11863.6.77.1.1.5.4	Integer32	read-write	Specify the priority of the BSR. The default value is 64.
tpPimStaticRpSet	1.3.6.1.4.1.11863.6.77.1.1.6
IP tpPimStaticRpAddress	1.3.6.1.4.1.11863.6.77.1.1.6.1	IpAddress	read-write	Specify the static RP address.
INT tpPimStaticRpOverride	1.3.6.1.4.1.11863.6.77.1.1.6.2	INTEGER	read-write	Select to enable or disable override mode. If the override mode is enabled, the static RP will take effect no matter the candidate RP is configured or not. Otherwise the static RP will be invalid when the candidate RP is configured.
tpPimCandidateRPSetTable	1.3.6.1.4.1.11863.6.77.1.1.7		not-accessible	The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages.
tpPimCandidateRPSetEntry	1.3.6.1.4.1.11863.6.77.1.1.7.1		not-accessible	An entry (conceptual row) in the pimRPSetTable.
OCT tpPimCRPSetInterface	1.3.6.1.4.1.11863.6.77.1.1.7.1.1	OCTET STRING	read-only	The c rp interface.
I32 tpPimCRPSetInterfaceIndex	1.3.6.1.4.1.11863.6.77.1.1.7.1.2	Integer32	read-write	The ifIndex value of this c rp interface.
INT tpPimCRPSetInterfaceType	1.3.6.1.4.1.11863.6.77.1.1.7.1.3	INTEGER	read-only	The interface type.
I32 tpPimCRPSetPriority	1.3.6.1.4.1.11863.6.77.1.1.7.1.4	Integer32	read-write	Specify the priority of the candidate RP. The default value is 192.
I32 tpPimCRPSetInterVal	1.3.6.1.4.1.11863.6.77.1.1.7.1.5	Integer32	read-write	Specify the interval of advertisement message of the candidate RP in seconds. The default value is 60.
TIK tpPimCRPSetNextAdvertisementTime	1.3.6.1.4.1.11863.6.77.1.1.7.1.6	TimeTicks	read-only	Show the remain time of next RP advertisement packet send.
INT tpPimCRPSetInterfaceStatus	1.3.6.1.4.1.11863.6.77.1.1.7.1.7	INTEGER	read-write	The interface type.
tpPimRPMappingTable	1.3.6.1.4.1.11863.6.77.1.1.8		not-accessible	Show the RP mapping information.
tpPimRPMappingEntry	1.3.6.1.4.1.11863.6.77.1.1.8.1		not-accessible	An entry (conceptual row) in the tpPimRPMappingTable. There is one entry per RP address for each IP multicast group.
IP tpPimRPGroupAddress	1.3.6.1.4.1.11863.6.77.1.1.8.1.1	IpAddress	read-only	The IP multicast group address for which this entry contains information about an RP.
IP tpPimRPAddress	1.3.6.1.4.1.11863.6.77.1.1.8.1.2	IpAddress	read-only	The IP multicast group address for which this entry contains PIM version 1 information about an RP.
IP tpPimRPInfoSource	1.3.6.1.4.1.11863.6.77.1.1.8.1.3	IpAddress	read-only	The state of the RP.
INT tpPimRPPriority	1.3.6.1.4.1.11863.6.77.1.1.8.1.4	INTEGER	read-only	Show the priority of the RP.
TIK tpPimRPHoldTime	1.3.6.1.4.1.11863.6.77.1.1.8.1.5	TimeTicks	read-only	Show the holdtime of the RP.
TIK tpPimRPExpire	1.3.6.1.4.1.11863.6.77.1.1.8.1.6	TimeTicks	read-only	Show the expiry time of the RP. If RP is static, the expiry time will be Never.
tplinkPimNotifications	1.3.6.1.4.1.11863.6.77.2

RFC description

Configures Protocol Independent Multicast settings on TP-Link network devices. Controls multicast tree thresholds, interface modes, and RP selection.

Start monitoring TP-Link Layer 3 managed switch/router (PIM sparse/dense mode config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TPLINK-PIM-MIB

What Is TPLINK-PIM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description