TELDAT-CFG-FastCFG-MIB

All MIBs › TELDAT-CFG-FastCFG-MIB

Category: Routing and Layer 3

Description: Manages Teldat router fast configuration parameters for rapid deployment and provisioning.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is TELDAT-CFG-FastCFG-MIB?

The TELDAT-CFG-FastCFG-MIB is a vendor-specific configuration module for Teldat routers, part of Teldat's broader enterprise SNMP MIB family for its CE/Dm-series routing and access platforms. It is oriented toward configuration data — a 'fast configuration' facility for rapidly provisioning router parameters — rather than performance counters or fault traps. While primarily a configuration-management MIB, reading back its objects lets an administrator confirm the software-level provisioning state actually applied to the device, serving as a check on configuration/software status rather than physical hardware health. No sample objects were available for this module, and its naming suggests reliance on Teldat's core router MIB tree (e.g. interface indices) for context rather than any IETF standard. It would typically be used during bulk or templated deployment of Teldat routers, where an operator pushes and then verifies fast-configuration settings via SNMP. Engineers can download the TELDAT-CFG-FastCFG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TELDAT-CFG-FastCFG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Teldat router/gateway

Monitoring Examples

No sample objects were provided for this module, so specific object names cannot be grounded here; based on its naming and description, it would contain configuration objects for rapidly provisioning router parameters (e.g. bulk parameter sets) rather than trap or performance data, used by an operator to push and then read back applied configuration values during router deployment.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString

From TELDAT-MIB

telproducts

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
teldatC3FastCfg	1.3.6.1.4.1.2007.4.54
udafocfg	1.3.6.1.4.1.2007.4.54.1
udafoTcpTable	1.3.6.1.4.1.2007.4.54.1.1		not-accessible	Profiles table for TCP connections.
udafoTcpEntry	1.3.6.1.4.1.2007.4.54.1.1.1		not-accessible	Each register is a profile with its parameters.
INT udafoTcpIndex	1.3.6.1.4.1.2007.4.54.1.1.1.1	INTEGER	read-only	Table index and number of TCP profile.
INT udafoTcpCommand	1.3.6.1.4.1.2007.4.54.1.1.1.2	INTEGER	read-write	Command field to add or delete TCP profiles. (1) ok, if last operation was correct. (just in get process.) (2) add, (just in set process.) (3) delete, (just in set process) (4) error, if last operation was incorrect. (just in get process.)
STR udafoTcpName	1.3.6.1.4.1.2007.4.54.1.1.1.3	DisplayString	read-write	TCP profile name.(Up to 15 characters.) Default value: NULL
STR udafoTcpNri	1.3.6.1.4.1.2007.4.54.1.1.1.4	DisplayString	read-write	Called Net Address. (Up to 15 digits. X character is also valid.) Default value: XXXXXXXXXXXXXXX
STR udafoTcpMainRemAdd	1.3.6.1.4.1.2007.4.54.1.1.1.5	DisplayString	read-write	Ip address of the first remote host. (Up to 25 characters.) Default value: 0.0.0.0
INT udafoTcpMainRemPort	1.3.6.1.4.1.2007.4.54.1.1.1.6	INTEGER	read-write	Port of the first remote host. Range:(0..65535). Default value: 20002
INT udafoTcpMainRemTmout	1.3.6.1.4.1.2007.4.54.1.1.1.7	INTEGER	read-write	Time out reply of the first remote host. Units: seconds. Range: (0..100). Default value: 5
STR udafoTcpSecRemAdd	1.3.6.1.4.1.2007.4.54.1.1.1.8	DisplayString	read-write	Ip address of the second remote host.(Up to 25 characters.) Default value: 0.0.0.0
INT udafoTcpSecRemPort	1.3.6.1.4.1.2007.4.54.1.1.1.9	INTEGER	read-write	Port of the second remote host. Range: (0..65535). Default value: 20002
INT udafoTcpSecRemTmout	1.3.6.1.4.1.2007.4.54.1.1.1.10	INTEGER	read-write	Time out reply of the second remote host. Units: seconds. Range: (0..100). Default value: 5
STR udafoTcpThirdRemAdd	1.3.6.1.4.1.2007.4.54.1.1.1.11	DisplayString	read-write	Ip address of the third remote host.(Up to 25 characters.) Default value: 0.0.0.0
INT udafoTcpThirdRemPort	1.3.6.1.4.1.2007.4.54.1.1.1.12	INTEGER	read-write	Port of the third remote host. Range: (0..65535). Default value: 20002
INT udafoTcpThirdRemTmout	1.3.6.1.4.1.2007.4.54.1.1.1.13	INTEGER	read-write	Time out reply of the third remote host. Units: seconds. Range: (0..100). Default value: 5
INT udafoTcpSendAck	1.3.6.1.4.1.2007.4.54.1.1.1.14	INTEGER	read-write	Enable Send ACK to HOST. Default value: 1 (NO)
udafoTrmtpTable	1.3.6.1.4.1.2007.4.54.1.2		not-accessible	Profiles table for TRMTP connections.
udafoTrmtpEntry	1.3.6.1.4.1.2007.4.54.1.2.1		not-accessible	Each register is a profile with its parameters.
INT udafoTrmtpIndex	1.3.6.1.4.1.2007.4.54.1.2.1.1	INTEGER	read-only	Table index and number of TRMTP profile.
INT udafoTrmtpCommmand	1.3.6.1.4.1.2007.4.54.1.2.1.2	INTEGER	read-write	Command field to add or delete TCP profiles. (1) ok, if last operation was correct. (just in get process.) (2) add, (just in set process.) (3) delete, (just in set process) (4) error, if last operation was incorrect. (just in get process.)
STR udafoTrmtpName	1.3.6.1.4.1.2007.4.54.1.2.1.3	DisplayString	read-write	TRMTP profile name. (Up to 15 characters.) Default value: NULL
STR udafoTrmtpNri	1.3.6.1.4.1.2007.4.54.1.2.1.4	DisplayString	read-write	Called Net Address. (Up to 15 digits. X character is also valid.) Default value: XXXXXXXXXXXXXXX
STR udafoTrmtpPrincIpAddr	1.3.6.1.4.1.2007.4.54.1.2.1.5	DisplayString	read-write	Ip address of the first remote host.(Up to 25 characters.) Default value: 0.0.0.0
INT udafoTrmtpPrincRemPort	1.3.6.1.4.1.2007.4.54.1.2.1.6	INTEGER	read-write	Port of the first remote host. Range: (0..65535) Default value: 20001
INT udafoTrmtpPrincN2	1.3.6.1.4.1.2007.4.54.1.2.1.7	INTEGER	read-write	Maximum number of retransmisions for the first remote host. Range: (0..65535) Default value: 3
INT udafoTrmtpPrincT1	1.3.6.1.4.1.2007.4.54.1.2.1.8	INTEGER	read-write	Acknowledge waiting time before retransmition for the first remote host. Units: seconds Range: (1..65535) Default value: 5
INT udafoTrmtpPrincT2	1.3.6.1.4.1.2007.4.54.1.2.1.9	INTEGER	read-write	Waiting time before getting out of an error state in the transmiter for the first remote host. Units: seconds Range (1..65535) Default value: 50
INT udafoTrmtpPrincT3	1.3.6.1.4.1.2007.4.54.1.2.1.10	INTEGER	read-write	Inactivity time before getting out of the DATA state in the transmiter for the first remote host. Units: seconds Range: (1..65535) Default value: 45
INT udafoTrmtpPrincT4	1.3.6.1.4.1.2007.4.54.1.2.1.11	INTEGER	read-write	Inactivity time (in seconds) before returning to OFF state in the receiver for the first remote host. Units: seconds Range: (1..65535) Default value: 100
STR udafoTrmtpSecIpAddr	1.3.6.1.4.1.2007.4.54.1.2.1.12	DisplayString	read-write	Ip address of the second remote host. Default value: 0.0.0.0
INT udafoTrmtpSecRemPort	1.3.6.1.4.1.2007.4.54.1.2.1.13	INTEGER	read-write	Port of the second remote host. Range: (0..65535) Default value: 20001
INT udafoTrmtpSecN2	1.3.6.1.4.1.2007.4.54.1.2.1.14	INTEGER	read-write	Maximum number of retransmisions for the second remote host. Range: (0..65535) Default value: 3
INT udafoTrmtpSecT1	1.3.6.1.4.1.2007.4.54.1.2.1.15	INTEGER	read-write	Acknowledge waiting time before retransmition for the second remote host. Units: seconds Range: (1..65535) Default value: 5
INT udafoTrmtpSecT2	1.3.6.1.4.1.2007.4.54.1.2.1.16	INTEGER	read-write	Waiting time before getting out of an error state in the transmiter for the second remote host. Units: seconds Range: (1..65535) Default value: 50
INT udafoTrmtpSecT3	1.3.6.1.4.1.2007.4.54.1.2.1.17	INTEGER	read-write	Inactivity time before getting out of the DATA state in the transmiter for the second remote host. Units: seconds Range: (0..65535) Default value: 45
INT udafoTrmtpSecT4	1.3.6.1.4.1.2007.4.54.1.2.1.18	INTEGER	read-write	Inactivity time before returning to OFF state in the receiver for the second remote host. Units: seconds Range: (1..65535) Default value: 100
STR udafoTrmtpThirdIpAddr	1.3.6.1.4.1.2007.4.54.1.2.1.19	DisplayString	read-write	Ip address of the third remote host. Default value: 0.0.0.0
INT udafoTrmtpThirdRemPort	1.3.6.1.4.1.2007.4.54.1.2.1.20	INTEGER	read-write	Port of the third remote host. Range: (0..65535) Default value: 20001
INT udafoTrmtpThirdN2	1.3.6.1.4.1.2007.4.54.1.2.1.21	INTEGER	read-write	Maximum number of retransmisions for the third remote host. Range: (0..65535) Default value: 3
INT udafoTrmtpThirdT1	1.3.6.1.4.1.2007.4.54.1.2.1.22	INTEGER	read-write	Ackknowledge waiting time before retransmition for the third remote host. Units: seconds Range: (1..65535) Default value: 5
INT udafoTrmtpThirdT2	1.3.6.1.4.1.2007.4.54.1.2.1.23	INTEGER	read-write	Waiting time before getting out of an error state in the transmiter for the third remote host. Units: seconds Range: (1..65535) Default value: 50
INT udafoTrmtpThirdT3	1.3.6.1.4.1.2007.4.54.1.2.1.24	INTEGER	read-write	Inactivity time before getting out of the DATA state in the transmiter for the third remote host. Units: seconds Range: (1..65535) Default value: 45
INT udafoTrmtpThirdT4	1.3.6.1.4.1.2007.4.54.1.2.1.25	INTEGER	read-write	Inactivity time before returning to OFF state in the receiver for the third remote host. Units: seconds Range: (1..65535) Default value: 100
udafoIfcTable	1.3.6.1.4.1.2007.4.54.1.3		not-accessible	Table of parameters for udafo interfaces.
udafoIfcEntry	1.3.6.1.4.1.2007.4.54.1.3.1		not-accessible	Each register contains the general parameters for each udafo interface. Maximum 4 interfaces.
INT udafoIfcIndex	1.3.6.1.4.1.2007.4.54.1.3.1.1	INTEGER	read-only	Table index and number of udafo interface.
INT udafoIfcSpeed	1.3.6.1.4.1.2007.4.54.1.3.1.2	INTEGER	read-write	Transmision speed. Units: bits per second. Range: (300..64000) Default value: 2400
INT udafoIfcProtocol	1.3.6.1.4.1.2007.4.54.1.3.1.3	INTEGER	read-write	Protocol for transmision. DOV(1), DAT(2), VISANET(3), TRANSPARENT(4), 7COMM(5), X28P(6).
INT udafoIfcTraMode	1.3.6.1.4.1.2007.4.54.1.3.1.4	INTEGER	read-write	Transmision mode: TCP(1), TRMTP(2), AUTO(3)
IP udafoIfcLocIpAddr	1.3.6.1.4.1.2007.4.54.1.3.1.5	IpAddress	read-write	Ip address of first remote host. Note: If trmtp mode is selected in this interface, ip address has no meaning,showing default value. In this situation the set command is disabled. Default value: 0.0.0.0
INT udafoIfcLocUdpPort	1.3.6.1.4.1.2007.4.54.1.3.1.6	INTEGER	read-write	Local Udp port. Note: If tcp mode is selected in this interface, Upd port has no meaning, showing default value. In this situation the set command is disabled. This parameter must be diferent for each interface. Range: (0..65535) Default value: 20001-20004 (2000X, where 'X' is interface number)
INT udafoIfcUnderlying	1.3.6.1.4.1.2007.4.54.1.3.1.7	INTEGER	read-write	The underlying of UDAFO can be WAN or UART Default value: UART
INT udafoIfcIdentifier	1.3.6.1.4.1.2007.4.54.1.3.1.8	INTEGER	read-write	The Terminal number. Default value: 1
INT udafoIfcSigIfcCtrl	1.3.6.1.4.1.2007.4.54.1.3.1.9	INTEGER	read-write	Enable serial line signal control (DTR). Default value: 1 (NO)
INT udafoIfcResponTime	1.3.6.1.4.1.2007.4.54.1.3.1.10	INTEGER	read-write	Response Time. When send a message, wait time for response from HOST or POS. (Some protocols used only) Range: (2..600) Default value: 20
udafoCnfgMisc	1.3.6.1.4.1.2007.4.54.1.4
INT udafoMiscDisServ	1.3.6.1.4.1.2007.4.54.1.4.1	INTEGER	read-write	Disable UDAFO service. Default value: 1 (NO DISABLED)
udafomon	1.3.6.1.4.1.2007.4.54.2
udafoTransaOkTable	1.3.6.1.4.1.2007.4.54.2.1		not-accessible	Table of the last successful transactions done with the datafono interface.
udafoTransaOkEntry	1.3.6.1.4.1.2007.4.54.2.1.1		not-accessible	Each register represents a transaction, giving its type, Ip address, Nri, net, date and time.
INT udafoTransaOkIndex	1.3.6.1.4.1.2007.4.54.2.1.1.1	INTEGER	read-only	Table index and number of transaction.
STR udafoTransaOkType	1.3.6.1.4.1.2007.4.54.2.1.1.2	DisplayString	read-only	Type of transaction. authorization or purchase (0) repayment (1) repetition (2) enquiry (3) close (4) account_entity selection (5) operation details (6) account enquiry (8) movement enquiry (9) memory inicialization/setup (M) Unknown (U)
IP udafoTransaOkIpAddr	1.3.6.1.4.1.2007.4.54.2.1.1.3	IpAddress	read-only	Host Ip address.
STR udafoTransaOkNri	1.3.6.1.4.1.2007.4.54.2.1.1.4	DisplayString	read-only	Called Net Address.
STR udafoTransaOkStartTime	1.3.6.1.4.1.2007.4.54.2.1.1.5	DisplayString	read-only	Start time of the operation.
STR udafoTransaOkEndTime	1.3.6.1.4.1.2007.4.54.2.1.1.6	DisplayString	read-only	End time of the operation.
STR udafoTransaOkDate	1.3.6.1.4.1.2007.4.54.2.1.1.7	DisplayString	read-only	Date of the transaction.
INT udafoTransaOkNet	1.3.6.1.4.1.2007.4.54.2.1.1.8	INTEGER	read-only	Number of net responsible for the transaction.
udafoTransaWrongTable	1.3.6.1.4.1.2007.4.54.2.2		not-accessible	Table of the last wrong transactions done with the datafono interface.
udafoTransaWrongEntry	1.3.6.1.4.1.2007.4.54.2.2.1		not-accessible	Each register represents a transaction, giving its type, Ip address, cause of failure, Nri, net, date and time.
INT udafoTransaWroIndex	1.3.6.1.4.1.2007.4.54.2.2.1.1	INTEGER	read-only	Table index and number of transaction.
STR udafoTransaWroType	1.3.6.1.4.1.2007.4.54.2.2.1.2	DisplayString	read-only	Type of transaction. authorization or purchase (0) repayment (1) repetition (2) enquiry (3) close (4) account_entity selection (5) operation details (6) account enquiry (8) movement enquiry (9) memory inicialization/setup (M) Unknown (U)
IP udafoTransaWroIpAddr	1.3.6.1.4.1.2007.4.54.2.2.1.3	IpAddress	read-only	Host Ip address.
STR udafoTransaWroNri	1.3.6.1.4.1.2007.4.54.2.2.1.4	DisplayString	read-only	Called Net Address.
INT udafoTransaWroCause	1.3.6.1.4.1.2007.4.54.2.2.1.5	INTEGER	read-only	Cause of failure in connection: 1.- The NRI send by datafono doesnt match with any configured profile. 2.- Disconnection received from DEP 3.- EOT received from TPV: invalid operation for the datafono. 4.- Unable to establish IP connection with host. 5.- End of TRMP connection. 6.- End of TCP connection by HOST.
STR udafoTransaWroStartTime	1.3.6.1.4.1.2007.4.54.2.2.1.6	DisplayString	read-only	Start time of operation.
STR udafoTransaWroEndTime	1.3.6.1.4.1.2007.4.54.2.2.1.7	DisplayString	read-only	End time of operation.
STR udafoTransaWroDate	1.3.6.1.4.1.2007.4.54.2.2.1.8	DisplayString	read-only	Date of the transaction.
INT udafoTransaWroNet	1.3.6.1.4.1.2007.4.54.2.2.1.9	INTEGER	read-only	Number of net responsible for the transaction.
udafoblockTable	1.3.6.1.4.1.2007.4.54.2.3		not-accessible	This table is a sequence of data blocks that contain the fornightly statistics.
udafoblockEntry	1.3.6.1.4.1.2007.4.54.2.3.1		not-accessible	Each entry is a data block. The size of each block is 1025 bytes, except for the last, that would be less.
INT udafoblkIndex	1.3.6.1.4.1.2007.4.54.2.3.1.1	INTEGER	read-only	This is the index of the table.
OCT udafoblkData	1.3.6.1.4.1.2007.4.54.2.3.1.2	OCTET STRING	read-only	Block data. For the last block, the size of the data block would be less than 1024.
INT udafoTransaOkDelete	1.3.6.1.4.1.2007.4.54.2.4	INTEGER	read-write	Command field to clear ALL statistics of this table. clear(1), (just in set process) ok(2), if last operation was correct (just in get process) error(3), if last operation was incorrect (just in get process) undefined(4), if no previous operation took place (just in get process)
INT udafoTransaWrongDelete	1.3.6.1.4.1.2007.4.54.2.5	INTEGER	read-write	Command field to clear ALL statistics of this table. clear(1), (just in set process) ok(2), if last operation was correct (just in get process) error(3), if last operation was incorrect (just in get process) undefined(4), if no previous operation took place (just in get process)

RFC description

Configures UDAFO (Universal Data & FAX Object) interfaces and TCP profiles for Teldat C3 routers including protocol selection.

Start monitoring Teldat router/gateway, CE/Dm-series (fast-configuration provisioning status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TELDAT-CFG-FastCFG-MIB

What Is TELDAT-CFG-FastCFG-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description