SWITCHING-SYSTEMS-MIB

All MIBs › SWITCHING-SYSTEMS-MIB

Category: Switch Management - General

Description: Defines management objects for switching system components, hardware, and operational state.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SWITCHING-SYSTEMS-MIB?

SWITCHING-SYSTEMS-MIB is a Synernetics module defining management objects for switching-system components, covering system identity, hardware characteristics, and operational state of the switch chassis. It exposes system ID/type/name, manufacturer, hardware revision, memory sizing (RAM, flash, NV memory), software revision, build time, and SNMP protocol revision/mode. Its monitoring emphasis is squarely on hardware and software status: confirming the installed hardware revision and available memory/flash capacity, and tracking the running software revision and build time to detect an unexpected or outdated firmware version on the switching system. It functions as a foundational system-identity MIB that other Synernetics product-specific MIBs likely build upon. It is deployed on Synernetics switching systems (legacy enterprise LAN switch/hub products). Engineers can download the SWITCHING-SYSTEMS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SWITCHING-SYSTEMS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Synernetics managed switching system

Monitoring Examples

An admin polls swSysSystemHardwareRevision and swSysSystemSoftwareRevision together to confirm a switch is running the expected firmware for its hardware revision, and checks swSysSystemMemorySize and swSysSystemFlashMemorySize against expected specs. An unexpected swSysSystemBuildTime or software revision mismatch across a fleet of otherwise-identical swSysSystemType devices would reveal a unit that was not upgraded during a fleet-wide firmware rollout.

What Can Be Monitored

system ID/type/name
hardware revision
memory/flash/NV memory size
software revision and build time
SNMP revision/mode

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
enterprises

From RFC1213-MIB

DisplayString

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
synernetics	1.3.6.1.4.1.114
switchingSystems	1.3.6.1.4.1.114.1
corebuilderProductsI	1.3.6.1.4.1.114.1.3
switchingSystemsMib	1.3.6.1.4.1.114.1.4
NTF swSysSystemOverTemperatureEvent	1.3.6.1.4.1.114.1.4.0.1			The trap that is generated when the system temperature exceeds a certain threshold.
NTF swSysPowerSupplyFailureEvent	1.3.6.1.4.1.114.1.4.0.2			The trap that is generated when a power supply unit fails.
NTF swSysChassisSlotOverTemperatureEvent	1.3.6.1.4.1.114.1.4.0.3			The trap that is generated when the temperature of a board in a particular slot exceeds a certain threshold.
NTF swSysChassisSlotInsertEvent	1.3.6.1.4.1.114.1.4.0.4			The trap that is generated when a board is inserted into a particular slot.
NTF swSysChassisSlotExtractEvent	1.3.6.1.4.1.114.1.4.0.5			The trap that is generated when a board is extracted from a particular slot.
NTF swSysBridgeAddressThresholdEvent	1.3.6.1.4.1.114.1.4.0.6			The trap that is generated when the number of addresses stored in the bridge reaches swSysBridgeAddressThreshold.
NTF swSysSystemFanFailureEvent	1.3.6.1.4.1.114.1.4.0.7			The trap that is generated when one of the system fans fails.
NTF swModuleCardSysOverTemperatureEvent	1.3.6.1.4.1.114.1.4.0.8			The trap that is generated when the temperature of the system exceeds a certain threshold. This trap is generated from agents that support the swSysModuleCardInfoTable.
NTF swModuleCardInsertEvent	1.3.6.1.4.1.114.1.4.0.9			The trap that is generated when a board is inserted into a particular modular slot. This trap is generated from agents that support the swSysModuleCardInfoTable.
NTF swModuleCardExtractEvent	1.3.6.1.4.1.114.1.4.0.10			The trap that is generated when a board is extracted from a particular modular slot. This trap is generated from agents that support the swSysModuleCardInfoTable.
swSysSystem	1.3.6.1.4.1.114.1.4.1
INT swSysSystemId	1.3.6.1.4.1.114.1.4.1.1	INTEGER	read-only	The unique identifier assigned to this system during manufacturing.
INT swSysSystemType	1.3.6.1.4.1.114.1.4.1.2	INTEGER	read-only	The type of system.
STR swSysSystemName	1.3.6.1.4.1.114.1.4.1.3	DisplayString	read-write	The text string describing this system.
STR swSysSystemManufacturer	1.3.6.1.4.1.114.1.4.1.4	DisplayString	read-only	The text string describing the manufacturer of this system.
OCT swSysSystemHardwareRevision	1.3.6.1.4.1.114.1.4.1.5	OCTET STRING	read-only	The revision level of the system, contained in two octets. The first octet indicates the artwork revision, and the second octet indicates the rework level.
INT swSysSystemMemorySize	1.3.6.1.4.1.114.1.4.1.6	INTEGER	read-only	The amount of memory (RAM), in bytes, present on the system processor board.
INT swSysSystemFlashMemorySize	1.3.6.1.4.1.114.1.4.1.7	INTEGER	read-only	The amount of flash memory, in bytes, present on the system processor board.
INT swSysSystemNvMemorySize	1.3.6.1.4.1.114.1.4.1.8	INTEGER	read-only	The amount of non-volatile memory, in bytes, present on the system processor board.
OCT swSysSystemSoftwareRevision	1.3.6.1.4.1.114.1.4.1.9	OCTET STRING	read-only	The revision number of the Switching Systems software. Each byte indicates the following: byte 0: major release number. byte 1: minor release number. byte 2: update number. byte 3: bits 7-6: release type. bits 5-0: supplemental identifier.
STR swSysSystemBuildTime	1.3.6.1.4.1.114.1.4.1.10	DisplayString	read-only	The build time of the system software.
INT swSysSystemSnmpRevision	1.3.6.1.4.1.114.1.4.1.11	INTEGER	read-only	The revision number of the SNMP agent implementation.
INT swSysSystemRequestedSnmpMode	1.3.6.1.4.1.114.1.4.1.12	INTEGER	read-write	This object describes the requested SNMP mode for the system. The value of this object indicates the mode that will become effective following a reboot of the system. Note that only a subset of the above values may be valid for some systems.
INT swSysSystemCurrentSnmpMode	1.3.6.1.4.1.114.1.4.1.13	INTEGER	read-only	This object describes the currently active SNMP mode for the system. Note that only a subset of the above values may be valid for some systems.
INT swSysSystemAction	1.3.6.1.4.1.114.1.4.1.14	INTEGER	read-write	This object, when read, always returns the value other(1). Setting this object to the value reset(2) causes a reset of the system. Setting this object to the value nvReset(3) causes the system's non-volatile configuration to be reset to the default values. The value other(1) is not a vaild value for set operations.
INT swSysSystemOvertemperature	1.3.6.1.4.1.114.1.4.1.15	INTEGER	read-only	This object indicates the current overtemperature status for the system. If the system does not support overtemperature detection, this object returns notSupported.
INT swSysSystemFanFailure	1.3.6.1.4.1.114.1.4.1.16	INTEGER	read-only	This object indicates the current fan status for the system. If the system does not support fan failure detection, this object returns notSupported.
INT swSysSystemProtocolMask	1.3.6.1.4.1.114.1.4.1.17	INTEGER	read-only	This object is a bit mask that indicates which protocols exist in the software image currently loaded in memory. The value of this OBJECT is a sum. It initially takes on the value 0, then for each protocol bit as defined below, 2 raised to the value of the (bit position - 1) is added to the sum. The following bits are defined: IP_ROUTING 0x00000001 IPX_ROUTING 0x00000002 DDP_ROUTING 0x00000004 A value of 0x00000000 indicates the standard switching software.
INT swSysSystemConsoleAccess	1.3.6.1.4.1.114.1.4.1.18	INTEGER	read-write	This object determines whether another device can remotely access the system console via Telnet, Rlogin, or modem port. An existing remote session will not be terminated when this value is modified.
STR swSysSystemConsoleReadPwd	1.3.6.1.4.1.114.1.4.1.19	DisplayString	read-write	This object is the console read-access password.
STR swSysSystemConsoleWritePwd	1.3.6.1.4.1.114.1.4.1.20	DisplayString	read-write	This object is the console write-access password. The read-write community string is required for access to this object.
STR swSysSystemConsoleAdminPwd	1.3.6.1.4.1.114.1.4.1.21	DisplayString	read-write	This object is the console admin-access password. The read-write community string is required for access to this object.
STR swSysSystemDateTime	1.3.6.1.4.1.114.1.4.1.22	DisplayString	read-write	The current date and time as reflected by the system clock in the format mm/dd/yy hh:mm:ss xM.
INT swSysSystemDSTime	1.3.6.1.4.1.114.1.4.1.23	INTEGER	read-write	This parameter specifies the displacement, in minutes, from non-daylight savings time. The swSysDSTime object, along with the swSysTimeZone object, allows the system to support Universal time for network communications spanning different time zones.
INT swSysSystemTimeZone	1.3.6.1.4.1.114.1.4.1.24	INTEGER	read-write	This parameter specifies, in minutes, displacement of the system west of Greenwich. A negative number for this parameter indicates how many minutes displacement east of Greenwich the site is located. A positive number indicates the number of minutes west of Greenwich.
INT swSysSystemCurrentFddiStationMode	1.3.6.1.4.1.114.1.4.1.25	INTEGER	read-only	This object describes the current FDDI station mode for systems that support multi-station mode.
INT swSysSystemRequestedFddiStationMode	1.3.6.1.4.1.114.1.4.1.26	INTEGER	read-write	This object describes the requested FDDI station mode for systems that support multi-station mode. The requested mode will become current during the next system reboot.
swSysSystemLog	1.3.6.1.4.1.114.1.4.1.27
INT swSysSystemLogEntryCurrentCount	1.3.6.1.4.1.114.1.4.1.27.1	INTEGER	read-only	The number of entries currently recorded in the system log.
INT swSysSystemLogMaxSize	1.3.6.1.4.1.114.1.4.1.27.2	INTEGER	read-only	The maximum number of events that can be recorded in the system log.
INT swSysSystemLogSeverityThreshold	1.3.6.1.4.1.114.1.4.1.27.3	INTEGER	read-write	This object determines the miminum serverety level of events recorded in the system log. For example, if the swSysSysteLogSeverityThreshold is set to errors(3) than only events which have serverity levels of error(3) or higher will be recorded.
swSysSystemLogTable	1.3.6.1.4.1.114.1.4.1.27.4		not-accessible	This table provides information on recorded system events.
swSysSystemLogEntry	1.3.6.1.4.1.114.1.4.1.27.4.1		not-accessible	A system log entry.
INT swSysSystemLogIndex	1.3.6.1.4.1.114.1.4.1.27.4.1.1	INTEGER	read-only	The index of the log entry relative to this entry.
INT swSysSystemLogSeverityLevel	1.3.6.1.4.1.114.1.4.1.27.4.1.2	INTEGER	read-only	Indicates the severity level of the log entry.
STR swSysSystemLogDateTime	1.3.6.1.4.1.114.1.4.1.27.4.1.3	DisplayString	read-only	Indicates the date and time of the log event and is formatted as follows: MM:DD:YY HH:MM:SS.
INT swSysSystemLogFacility	1.3.6.1.4.1.114.1.4.1.27.4.1.4	INTEGER	read-only	The facility which entered the event in the log. fcmlmm(6) represents those events which may be common to the Lanplex Management Module (LMM) and the FDDI Concentrator Module (FCM). lmmfddi(6) represents those events specific to the FDDI portion of the LMM and lmmboard represents general events logged by the LMM.
STR swSysSystemLogMessage	1.3.6.1.4.1.114.1.4.1.27.4.1.5	DisplayString	read-only	The recorded log message.
MAC swSysSystemBaseMACAddress	1.3.6.1.4.1.114.1.4.1.28	MacAddress	read-only	The base MAC address for the system.
INT swSysSystemMACAddressCount	1.3.6.1.4.1.114.1.4.1.29	INTEGER	read-only	The number of MAC addresses allocated to this system.
STR swSysSystemChassisSerialNumber	1.3.6.1.4.1.114.1.4.1.30	DisplayString	read-only	The serial number of the chassis.
INT swSysSystemFPMemorySize	1.3.6.1.4.1.114.1.4.1.31	INTEGER	read-only	The amount of frame processor memory (RAM), in bytes.
INT swSysSystemBufferSize	1.3.6.1.4.1.114.1.4.1.32	INTEGER	read-only	The amount of buffer memory, in bytes.
swSysSlot	1.3.6.1.4.1.114.1.4.2
INT swSysSlotCount	1.3.6.1.4.1.114.1.4.2.1	INTEGER	read-only	The count of slots in the chassis.
swSysSlotTable	1.3.6.1.4.1.114.1.4.2.2		not-accessible	A list of slot entries. A single entry exists in this list for each slot in the chassis.
swSysSlotEntry	1.3.6.1.4.1.114.1.4.2.2.1		not-accessible	A slot entry contains information about a particular slot.
INT swSysSlotIndex	1.3.6.1.4.1.114.1.4.2.2.1.1	INTEGER	read-only	The index of the slot identified by this entry.
INT swSysSlotBoardType	1.3.6.1.4.1.114.1.4.2.2.1.2	INTEGER	read-only	The type of board residing in the slot identified by this entry.
OCT swSysSlotBoardRevision	1.3.6.1.4.1.114.1.4.2.2.1.3	OCTET STRING	read-only	The revision number of the board in the slot identified by this entry. If the slot is empty, or the revision is unknown this object returns a zero length string.
INT swSysSlotBoardStatus	1.3.6.1.4.1.114.1.4.2.2.1.4	INTEGER	read-only	The status of the board in the slot identified by this entry.
STR swSysSlotBoardName	1.3.6.1.4.1.114.1.4.2.2.1.5	DisplayString	read-only	The text string describing the board in the slot identified by this entry.
STR swSysSlotBoardNameAbbrev	1.3.6.1.4.1.114.1.4.2.2.1.6	DisplayString	read-only	The abbreviation used to describe the board in the slot identified by this entry.
INT swSysSlotEthernetPortCount	1.3.6.1.4.1.114.1.4.2.2.1.7	INTEGER	read-only	The count of ethernet ports in the slot identified by this entry.
INT swSysSlotFddiMacCount	1.3.6.1.4.1.114.1.4.2.2.1.8	INTEGER	read-only	The count of FDDI MACs in the slot identified by this entry.
INT swSysSlotFddiPortCount	1.3.6.1.4.1.114.1.4.2.2.1.9	INTEGER	read-only	The count of FDDI ports in the slot identified by this entry.
INT swSysSlotOvertemperature	1.3.6.1.4.1.114.1.4.2.2.1.10	INTEGER	read-only	This object indicates the current overtemperature status for the slot. If the slot does not support overtemperature detection, this object returns notSupported.
INT swSysSlotTokenRingPortCount	1.3.6.1.4.1.114.1.4.2.2.1.11	INTEGER	read-only	The count of TokenRing ports in the slot identified by this entry.
STR swSysSlotBoardRevStr	1.3.6.1.4.1.114.1.4.2.2.1.12	DisplayString	read-only	This revision number of the board in the slot identified by this entry. If the slot is empty, or the revision is unknown this object returns a zero length string. The format of the string is XX.YY, where the XX is the major revision (artwork), the YY is the minor revision (rework)
INT swSysSlotConverterBad	1.3.6.1.4.1.114.1.4.2.2.1.13	INTEGER	read-only	This object indicates the current status +12V->+5V converter for the slot. If the slot does not support +12V->+5V converter detection, this object returns notSupported.
swSysControlPanel	1.3.6.1.4.1.114.1.4.3
OCT swSysControlPanelHardwareRevision	1.3.6.1.4.1.114.1.4.3.1	OCTET STRING	read-only	An 8-bit value specifying the revision level of the control panel hardware.
OCT swSysControlPanelSoftwareRevision	1.3.6.1.4.1.114.1.4.3.2	OCTET STRING	read-only	An 8-bit value specifying the revision level of the control panel software.
INT swSysControlPanelLines	1.3.6.1.4.1.114.1.4.3.3	INTEGER	read-only	The number of lines in the control panel display.
INT swSysControlPanelColumns	1.3.6.1.4.1.114.1.4.3.4	INTEGER	read-only	The number of columns in the control panel display.
OCT swSysControlPanelText	1.3.6.1.4.1.114.1.4.3.5	OCTET STRING	read-only	The currently displayed text in the control panel display.
INT swSysControlPanelAccess	1.3.6.1.4.1.114.1.4.3.6	INTEGER	read-write	This object determines whether modifications to system configuration are allowed via the Control Panel
swSysPowerSupply	1.3.6.1.4.1.114.1.4.4
INT swSysPowerSupplyCount	1.3.6.1.4.1.114.1.4.4.1	INTEGER	read-only	The count of power supplies in the system.
swSysPowerSupplyStatusTable	1.3.6.1.4.1.114.1.4.4.2		not-accessible	A list of power supply status entries.
swSysPowerSupplyStatusEntry	1.3.6.1.4.1.114.1.4.4.2.1		not-accessible	A power supply status entry contains information about a particular power supply.
INT swSysPowerSupplyStatusIndex	1.3.6.1.4.1.114.1.4.4.2.1.1	INTEGER	read-only	The unique index of the power supply identified by this entry.
INT swSysPowerSupplyStatus	1.3.6.1.4.1.114.1.4.4.2.1.2	INTEGER	read-only	This object represents the power supply status. The value is a sum. It initially takes on the value 0, then for each type which is active, 2 raised to a power is added to the sum. The powers are according to the following table. For the 6000 Backbone Aggregator an over temp for power supply 1 and power supply 2 will be reported as a power supply 1 Over Temperature Failure, and a fan failure will be reported as a power supply 2 Over Temperature Failure. Failure Type Power AC Failure 0 Plus 5 Failure 1 Plus 12 Failure 2 Over Temperature Failure 3 Power Supply Inserted 4 Power Supply Extracted 5
INT swSysPowerSupplyStatusSupported	1.3.6.1.4.1.114.1.4.4.2.1.3	INTEGER	read-only	This object represents the various power supply status types which are supported. The value is a sum. It initially takes on the value 0, then for each type which is supported, 2 raised to a power is added to the sum. The powers are according to the following table: Failure Type Power AC Failure 0 Plus 5 Failure 1 Plus 12 Failure 2 Over Temperature Failure 3 Power Supply Inserted 4 Power Supply Extracted 5 This object used in conjunction with the swSysPowerSupplyStatus object for a given power supply provide a complete picture of the status of the power supply.
swSysSnmp	1.3.6.1.4.1.114.1.4.5
INT swSysSnmpAgentId	1.3.6.1.4.1.114.1.4.5.1	INTEGER	read-only	The unique id for this SNMP agent within the system.
OCT swSysSnmpInternalAgentTrapMask	1.3.6.1.4.1.114.1.4.5.2	OCTET STRING	read-write	This value is a bit string that indicates which traps are enabled for transmit to other agents in the system. The octet string value is treated as a 64-bit integer value. The value is a sum. It initially takes on the value 0, then for each trap which is enabled, 2 raised to the value of (swSysAgentTrapDescriptionIndex - 1) for that trap is added to the sum.
INT swSysSnmpInternalAgentTrapDestinationMask	1.3.6.1.4.1.114.1.4.5.3	INTEGER	read-write	A value which indicates to which other agents in the system traps should be sent. The value is a sum. It initially takes on the value 0, then for each agent which is to receive traps, 2 raised to the value of (swSysSnmpAgentId - 1) for that agent is added to the sum. Note that only traps which are enabled according to the value of the swSysSnmpInternalAgentTrapMask object will be forwarded, and that each trap which is forwarded will be transmitted to each agent identified by this mask.
INT swSysSnmpProxyInternalRequests	1.3.6.1.4.1.114.1.4.5.4	INTEGER	read-write	This object determines if this agent will proxy requests to other agents in the system. If the value of this object is true(1), this agent will proxy requests to other agents in the chassis.
INT swSysSnmpInternalProxyRequestMaxAge	1.3.6.1.4.1.114.1.4.5.5	INTEGER	read-write	The maximum time, in seconds, an internal proxy request will remain queued waiting for a response before being discarded. Note that when the value of swSysSnmpProxyInternalRequests is false(2), the value of this object is ignored.
INT swSysSnmpProxyInternalTraps	1.3.6.1.4.1.114.1.4.5.6	INTEGER	read-write	This object determines if this agent will generate proxy traps for those traps received from other agents in the system. If the value of this object is true(1), this agent will generate proxy traps for those received from other agents in the chassis. Note that agents will not proxy traps to other agents within the system to prevent looping of traps.
swSysSnmpInternalProxyTable	1.3.6.1.4.1.114.1.4.5.7		not-accessible	A list of SNMP internal agent proxy entries. An entry in this table exists for each agent in the system that can be reached by this agent via the internal proxy mechanism.
swSysSnmpInternalProxyEntry	1.3.6.1.4.1.114.1.4.5.7.1		not-accessible	An entry identifies the communities available for communicating with another agent in the system via the internal proxy mechanism.
INT swSysSnmpInternalProxyAgentId	1.3.6.1.4.1.114.1.4.5.7.1.1	INTEGER	read-only	The id of the agent identified by this entry.
INT swSysSnmpInternalProxyAccessClass	1.3.6.1.4.1.114.1.4.5.7.1.2	INTEGER	read-only	The access to MIB objects supported by the agent identified by this entry provided by this agent, when using the community string identified by the corresponding value of swSysSnmpInternalProxyCommunity.
OCT swSysSnmpInternalProxyCommunity	1.3.6.1.4.1.114.1.4.5.7.1.3	OCTET STRING	read-only	A community which allows access to MIB objects supported by the agent identified by this entry.
swSysAgent	1.3.6.1.4.1.114.1.4.6
INT swSysAgentRequestMaxAge	1.3.6.1.4.1.114.1.4.6.1	INTEGER	read-write	The maximum time, in seconds, a local SNMP request will remain queued waiting for a response before being discarded.
INT swSysAgentProxyRemoteSmtRequests	1.3.6.1.4.1.114.1.4.6.2	INTEGER	read-write	This object determines if this agent will proxy SMT requests to other FDDI stations. If the value of this object is true(1), this agent will proxy SMT requests to other stations. Note that only a subset of the above values may be valid for some systems.
INT swSysAgentRemoteSmtProxyRequestMaxAge	1.3.6.1.4.1.114.1.4.6.3	INTEGER	read-write	The maximum time, in seconds, an SMT proxy request will remain queued waiting for a response before being discarded. Note that when the value of swSysAgentProxyRemoteSmtRequests is false(2), the value of this object is ignored.
INT swSysAgentProxyRemoteSmtEvents	1.3.6.1.4.1.114.1.4.6.4	INTEGER	read-write	This object determines if this agent will generate traps for SMT events occuring at other stations. If the value of this object is true(1), this agent will generate traps for all SMT events, those which occur locally, and those which occur at other stations. If the value of this object is false(2), this agent will only generate traps for events which occur locally. Note that only a subset of the above values may be valid for some systems.
swSysAgentTrapDescriptionTable	1.3.6.1.4.1.114.1.4.6.5		not-accessible	This table contains a listing of trap descriptions for each trap supported by this agent. This provides a relationship between a trap index, and the trap enterprise oid and trap number for a given trap. In all cases except for the MIB-2 generic traps, the enterprise under which a trap is defined is the same as that appearing in the ENTERPRISE portion of the trap.
swSysAgentTrapDescriptionTableEntry	1.3.6.1.4.1.114.1.4.6.5.1		not-accessible	Information relating a trap index to a specific trap enterprise oid and trap number.
INT swSysAgentTrapDescriptionIndex	1.3.6.1.4.1.114.1.4.6.5.1.1	INTEGER	read-only	A unique index corresponding to the trap described by this entry. This value of this object corresponding to a particular trap will remain constant accross system resets.
OID swSysAgentTrapEnterprise	1.3.6.1.4.1.114.1.4.6.5.1.2	OBJECT IDENTIFIER	read-only	The enterpise under which the trap identified by this entry is defined.
INT swSysAgentTrapNumber	1.3.6.1.4.1.114.1.4.6.5.1.3	INTEGER	read-only	The number of the trap identified by this entry, within the enterprise where it is defined.
swSysAgentTrapDestinationTable	1.3.6.1.4.1.114.1.4.6.6		not-accessible	This table contains information specifying which traps will be transmitted to a given destination address. The table is indexed by the destination address type and destination address. Each entry in the table with a status of valid identifies a set of traps which, when generated, will be transmitted to the corresponding destination address listed in that entry.
swSysAgentTrapDestinationTableEntry	1.3.6.1.4.1.114.1.4.6.6.1		not-accessible	Information relating a set of traps and a destination address to which each trap in ths set will be transmitted when it is generated. To create a new entry, set a non-existent instance of swSysAgentTrapDestinationTrapMask to a valid value. To remove an entry, set the instance of swSysAgentTrapDestinationEntryStatus for the entry to invalid(2).
INT swSysAgentTrapDestinationAddressType	1.3.6.1.4.1.114.1.4.6.6.1.1	INTEGER	read-only	The type of address identified by this entry.
OCT swSysAgentTrapDestinationAddress	1.3.6.1.4.1.114.1.4.6.6.1.2	OCTET STRING	read-only	The address, of the type specified by the corresponding value of swSysAgentTrapDestinationAddressType, to which the set of traps identified by this entry are to be transmitted.
OCT swSysAgentTrapDestinationTrapMask	1.3.6.1.4.1.114.1.4.6.6.1.3	OCTET STRING	read-write	This value is a bit string that indicates which traps are enabled for the address identified by this entry. The octet string value is treated as a 64-bit value. The value is a sum. It initially takes on the value 0, then for each trap which is enabled, 2 raised to the value of (swSysAgentTrapDescriptionIndex - 1) for that trap is added to the sum. A new entry in the table is created by setting the value of this object for a new destination address type and destination address. Note that an octet string of all zeros is not a valid value for this object.
INT swSysAgentTrapDestinationEntryStatus	1.3.6.1.4.1.114.1.4.6.6.1.4	INTEGER	read-write	The status of the trap destination table entry. Setting this object to invalid(1) has the effect of removing the corresponding entry from the table.
STR swSysAgentReadCommunity	1.3.6.1.4.1.114.1.4.6.7	DisplayString	read-write	This object is the read community string when access is made via SNMP, see RFC1157.
STR swSysAgentReadWriteCommunity	1.3.6.1.4.1.114.1.4.6.8	DisplayString	read-write	This object is the read-write community string when access is made via SNMP, see RFC1157. The read-write community string is required to access this object.
swSysInterface	1.3.6.1.4.1.114.1.4.7
swSysInterfaceLocationTable	1.3.6.1.4.1.114.1.4.7.1		not-accessible	A list of interface location entries. A single entry exists in this list for each interface managed by this agent.
swSysInterfaceLocationEntry	1.3.6.1.4.1.114.1.4.7.1.1		not-accessible	An interface location entry describes the location of a particular interface managed by this agent.
INT swSysInterfaceLocationIfIndex	1.3.6.1.4.1.114.1.4.7.1.1.1	INTEGER	read-only	The value of the MIB-II ifIndex corresponding to the interface identified by this entry.
INT swSysInterfaceLocationInterfaceType	1.3.6.1.4.1.114.1.4.7.1.1.2	INTEGER	read-only	The type of the physical implementation of the interface identified by this entry.
INT swSysInterfaceLocationType	1.3.6.1.4.1.114.1.4.7.1.1.3	INTEGER	read-only	The type of location where the interface identified by this entry is physically located.
INT swSysInterfaceLocationTypeIndex	1.3.6.1.4.1.114.1.4.7.1.1.4	INTEGER	read-only	The index of the location identified by the corresponding instance of swSysInterfaceLocationType where the interface identified by this entry is physically located.
INT swSysInterfaceLocationLocalIndex	1.3.6.1.4.1.114.1.4.7.1.1.5	INTEGER	read-only	The local index of the interface identified by this entry relative to its type specified by the corresponding value of swSysInterfaceLocationInterfaceType, and the location specified by the corresponding values of swSysInterfaceLocationType and swSysInterfaceLocationTypeIndex.
INT swSysInterfaceLocationSystemModuleIndex	1.3.6.1.4.1.114.1.4.7.1.1.6	INTEGER	read-only	The system module index of the interface idnetified by this entry. Ths index can be used to acquire the module information from the s2SysModuleCardGroup and the swSysDiagnosticsGroup groups.
swSysEthernetPort	1.3.6.1.4.1.114.1.4.8
INT swSysEthernetPortCount	1.3.6.1.4.1.114.1.4.8.1	INTEGER	read-only	The count of ethernet ports managed by this agent.
swSysEthernetPortTable	1.3.6.1.4.1.114.1.4.8.2		not-accessible	A list of ethernet port entries. A single entry exists in this list for each ethernet port managed by this agent.
swSysEthernetPortEntry	1.3.6.1.4.1.114.1.4.8.2.1		not-accessible	An ethernet port entry contains information about a particular ethernet port managed by this agent.
INT swSysEthernetPortIndex	1.3.6.1.4.1.114.1.4.8.2.1.1	INTEGER	read-only	The index of the ethernet port identified by this entry, relative to this agent.
INT swSysEthernetPortIfIndex	1.3.6.1.4.1.114.1.4.8.2.1.2	INTEGER	read-only	The value of the MIB-II ifIndex corresponding to the ethernet port identified by this entry.
STR swSysEthernetPortLabel	1.3.6.1.4.1.114.1.4.8.2.1.3	DisplayString	read-write	An ASCII text string describing the ethernet port identified by this entry.
INT swSysEthernetPortLinkStatus	1.3.6.1.4.1.114.1.4.8.2.1.4	INTEGER	read-only	The current value of the link status for the ethernet port identified by this entry.
INT swSysEthernetPortType	1.3.6.1.4.1.114.1.4.8.2.1.5	INTEGER	read-only	Specific port type description for the ethernet port identified by this entry.
swSysEthernetPortRateTable	1.3.6.1.4.1.114.1.4.8.3		not-accessible	A list of ethernet port rate entries. A single entry exists in this list for each ethernet port, managed by this agent, which supports rate information.
swSysEthernetPortRateEntry	1.3.6.1.4.1.114.1.4.8.3.1		not-accessible	An ethernet port rate entry contains rate statistics for a particular ethernet port managed by this agent. Rate statistics are calculated based on a one second sampling interval.
INT swSysEthernetPortRateIndex	1.3.6.1.4.1.114.1.4.8.3.1.1	INTEGER	read-only	The index of the ethernet port identified by this entry, relative to this agent.
INT swSysEthernetPortRateByteReceiveRate	1.3.6.1.4.1.114.1.4.8.3.1.2	INTEGER	read-only	The average number of bytes received per second by the ethernet port identified by this entry during the most recent sampling period.
INT swSysEthernetPortRatePeakByteReceiveRate	1.3.6.1.4.1.114.1.4.8.3.1.3	INTEGER	read-only	The peak value of swSysEthernetPortRateByteReceiveRate since the system was last initialized for the ethernet port identified by this entry.
INT swSysEthernetPortRateFrameReceiveRate	1.3.6.1.4.1.114.1.4.8.3.1.4	INTEGER	read-only	The average number of frames received per second by the ethernet port identified by this entry during the most recent sampling period.
INT swSysEthernetPortRatePeakFrameReceiveRate	1.3.6.1.4.1.114.1.4.8.3.1.5	INTEGER	read-only	The peak value of swSysEthernetPortRateFrameReceiveRate since the system was last initialized for the ethernet port identified by this entry.
INT swSysEthernetPortRateByteTransmitRate	1.3.6.1.4.1.114.1.4.8.3.1.6	INTEGER	read-only	The average number of bytes transmitted per second by the ethernet port identified by this entry during the most recent sampling period.
INT swSysEthernetPortRatePeakByteTransmitRate	1.3.6.1.4.1.114.1.4.8.3.1.7	INTEGER	read-only	The peak value of swSysEthernetPortRateByteTransmitRate since the system was last initialized for the ethernet port identified by this entry.
INT swSysEthernetPortRateFrameTransmitRate	1.3.6.1.4.1.114.1.4.8.3.1.8	INTEGER	read-only	The average number of frames transmitted per second by the ethernet port identified by this entry during the most recent sampling period.
INT swSysEthernetPortRatePeakFrameTransmitRate	1.3.6.1.4.1.114.1.4.8.3.1.9	INTEGER	read-only	The peak value of swSysEthernetPortRateFrameTransmitRate since the system was last initialized for the ethernet port identified by this entry.
swSysSmt	1.3.6.1.4.1.114.1.4.9
INT swSysSmtCount	1.3.6.1.4.1.114.1.4.9.1	INTEGER	read-only	The count of SMTs managed by this agent.
swSysSmtFddiMacBeaconTable	1.3.6.1.4.1.114.1.4.9.4		not-accessible	A list of FDDI MAC beacon entries. A single entry exists in this list for each FDDI MAC, managed by this agent, which supports MAC beacon history.
swSysSmtFddiMacBeaconEntry	1.3.6.1.4.1.114.1.4.9.4.1		not-accessible	An FDDI MAC beacon entry contains information about a particular FDDI MAC's beacon history.
INT swSysSmtFddiMacBeaconSmtIndex	1.3.6.1.4.1.114.1.4.9.4.1.1	INTEGER	read-only	The index of the SMT instance identified by this entry, relative to this agent.
INT swSysSmtFddiMacBeaconIndex	1.3.6.1.4.1.114.1.4.9.4.1.2	INTEGER	read-only	The index of the FDDI MAC identified by this entry, within the SMT identified by this entry.
OCT swSysSmtFddiMacBeaconHistory	1.3.6.1.4.1.114.1.4.9.4.1.3	OCTET STRING	read-only	This object gives a history of the most recent beacon information received on the FDDI MAC identified by this entry. It can contain up to a maximum of eight records. Each record is of the form: source MAC: 6 bytes beacon data length: 2 bytes. beacon data: 0-16 bytes.
swSysSmtFddiMacRateTable	1.3.6.1.4.1.114.1.4.9.5		not-accessible	A list of FDDI MAC rate entries. A single entry exists in this list for each FDDI MAC, managed by this agent, which supports rate statistics.
swSysSmtFddiMacRateEntry	1.3.6.1.4.1.114.1.4.9.5.1		not-accessible	An FDDI MAC rate entry contains rate statistics for a particular FDDI MAC managed by this agent. Rate statistics are calculated based on a one second sampling interval.
INT swSysSmtFddiMacRateSmtIndex	1.3.6.1.4.1.114.1.4.9.5.1.1	INTEGER	read-only	The index of the SMT instance identified by this entry, relative to this agent.
INT swSysSmtFddiMacRateIndex	1.3.6.1.4.1.114.1.4.9.5.1.2	INTEGER	read-only	The index of the FDDI MAC identified by this entry, within the SMT identified by this entry.
INT swSysSmtFddiMacRateByteReceiveRate	1.3.6.1.4.1.114.1.4.9.5.1.3	INTEGER	read-only	The average number of bytes received per second by the FDDI MAC identified by this entry during the most recent sampling period.
INT swSysSmtFddiMacRatePeakByteReceiveRate	1.3.6.1.4.1.114.1.4.9.5.1.4	INTEGER	read-only	The peak value of swSysSmtFddiMacByteReceiveRate since the system was last initialized for the FDDI MAC identified by this entry.
INT swSysSmtFddiMacRateFrameReceiveRate	1.3.6.1.4.1.114.1.4.9.5.1.5	INTEGER	read-only	The average number of frames received per second by the FDDI MAC identified by this entry during the most recent sampling period.
INT swSysSmtFddiMacRatePeakFrameReceiveRate	1.3.6.1.4.1.114.1.4.9.5.1.6	INTEGER	read-only	The peak value of swSysSmtFddiMacRateFrameReceiveRate since the system was last initialized for the FDDI MAC identified by this entry.
INT swSysSmtFddiMacRateByteTransmitRate	1.3.6.1.4.1.114.1.4.9.5.1.7	INTEGER	read-only	The average number of bytes transmitted per second by the FDDI MAC identified by this entry during the most recent sampling period.
INT swSysSmtFddiMacRatePeakByteTransmitRate	1.3.6.1.4.1.114.1.4.9.5.1.8	INTEGER	read-only	The peak value of swSysSmtFddiMacByteTransmitRate since the system was last initialized for the FDDI MAC identified by this entry.
INT swSysSmtFddiMacRateFrameTransmitRate	1.3.6.1.4.1.114.1.4.9.5.1.9	INTEGER	read-only	The average number of frames transmitted per second by the FDDI MAC identified by this entry during the most recent sampling period.
INT swSysSmtFddiMacRatePeakFrameTransmitRate	1.3.6.1.4.1.114.1.4.9.5.1.10	INTEGER	read-only	The peak value of swSysSmtFddiMacFrameTransmitRate since the system was last initialized for the FDDI MAC identified by this entry.
swSysSmtFddiPortTable	1.3.6.1.4.1.114.1.4.9.6		not-accessible	A list of FDDI port entries. A single entry exists in this list for each FDDI port managed by this agent.
swSysSmtFddiPortEntry	1.3.6.1.4.1.114.1.4.9.6.1		not-accessible	An FDDI port entry contains information about a particular FDDI port managed by this agent.
INT swSysSmtFddiPortSmtIndex	1.3.6.1.4.1.114.1.4.9.6.1.1	INTEGER	read-only	The index of the SMT instance identified by this entry, relative to this agent.
INT swSysSmtFddiPortIndex	1.3.6.1.4.1.114.1.4.9.6.1.2	INTEGER	read-only	The index of the FDDI port identified by this entry, within the SMT identified by this entry.
INT swSysSmtFddiPortLocationType	1.3.6.1.4.1.114.1.4.9.6.1.3	INTEGER	read-only	The type of location where the FDDI port identified by this entry is physically located.
INT swSysSmtFddiPortLocationTypeIndex	1.3.6.1.4.1.114.1.4.9.6.1.4	INTEGER	read-only	The index of the location identified by the corresponding instance of swSysSmtFddiPortLocationType where the FDDI port identified by this entry is physically located.
INT swSysSmtFddiPortLocationLocalIndex	1.3.6.1.4.1.114.1.4.9.6.1.5	INTEGER	read-only	The local index of the FDDI port identified by this entry relative to the location specified by the corresponding values of swSysSmtFddiPortLocationType and swSysSmtFddiPortLocationTypeIndex.
STR swSysSmtFddiPortLabel	1.3.6.1.4.1.114.1.4.9.6.1.6	DisplayString	read-write	An ASCII text string describing the FDDI port identified by this entry.
swSysSmtFddiMacLocationTable	1.3.6.1.4.1.114.1.4.9.7		not-accessible	An FDDI MAC Location table contains information to assign an FDDI MAC to a different Location. The system must be rebooted after all changes to this table are completed in order that the changes take effect.
swSysSmtFddiMacLocationEntry	1.3.6.1.4.1.114.1.4.9.7.1		not-accessible	An FDDI MAC entry contains information to assign an FDDI MAC to a different Location.
INT swSysSmtFddiMacLocationSmtIndex	1.3.6.1.4.1.114.1.4.9.7.1.1	INTEGER	read-only	The index of the SMT instance identified by this entry, relative to the agent.
INT swSysSmtFddiMacLocationIndex	1.3.6.1.4.1.114.1.4.9.7.1.2	INTEGER	read-only	The index of the FDDI MAC instance identified by this entry, relative to the SMT identified by this entry.
INT swSysSmtFddiMacCurrentLocation	1.3.6.1.4.1.114.1.4.9.7.1.3	INTEGER	read-only	Indicates whether the MAC identified by this entry is assigned to a backplane FDDI station (internal) or an FDDI station configured on a module (external.)
INT swSysSmtFddiMacRequestedLocation	1.3.6.1.4.1.114.1.4.9.7.1.4	INTEGER	read-write	The Location which the MAC identified by this entry is to be assigned to during the next reboot.
INT swSysSmtFddiMacAvailableLocation	1.3.6.1.4.1.114.1.4.9.7.1.5	INTEGER	read-only	Indicates the Location(s) available for this MAC. A mac Location which can be modified to either the interanl backplane or an external FDDI port is indicated by internalOrExternal(3).
swSysSmtFddiMacStationTable	1.3.6.1.4.1.114.1.4.9.8		not-accessible	An FDDI station MAC table contains information to assign an FDDI MAC to an FDDI Station. The system must be rebooted after all changes to this table are completed in order that the changes take effect.
swSysSmtFddiMacStationEntry	1.3.6.1.4.1.114.1.4.9.8.1		not-accessible	An FDDI MAC entry contains information to assign an FDDI MAC to an FDDI Station.
INT swSysSmtFddiMacStationSmtIndex	1.3.6.1.4.1.114.1.4.9.8.1.1	INTEGER	read-only	The index of the SMT instance identified by this entry, relative to this agent.
INT swSysSmtFddiMacStationIndex	1.3.6.1.4.1.114.1.4.9.8.1.2	INTEGER	read-only	The index of the MAC instance identified by this entry, relative to the SMT identified by this entry.
INT swSysSmtFddiMacCurrentStation	1.3.6.1.4.1.114.1.4.9.8.1.3	INTEGER	read-only	Indicates which FDDI station that the FDDI MAC identified by this entry is assigned to. A value of 0 indicates that the mac is assigned to an external station. Otherwise the value represents the internal backplane station number.
INT swSysSmtFddiMacRequestedStation	1.3.6.1.4.1.114.1.4.9.8.1.4	INTEGER	read-write	Indicates which FDDI station the FDDI MAC identified by this entry will be set to during the next system reboot. A value of 0 indicates an external station. Otherwise the value represents the internal backplane station number.
INT swSysSmtFddiMacAvailableStations	1.3.6.1.4.1.114.1.4.9.8.1.5	INTEGER	read-only	This value is a sum. Setting of the first bit (LSB) indicates that the MAC can be assigned to an external station. Available backplane stations are indicated by adding 2^StationNumber to the sum. Where StationNumber represents a backplane station number.
swSysSmtFddiPortStationTable	1.3.6.1.4.1.114.1.4.9.9		not-accessible	An FDDI station Port table contains information to assign an FDDI Port to an FDDI Station. The system must be rebooted after all changes to this table are completed in order that the changes take effect.
swSysSmtFddiPortStationEntry	1.3.6.1.4.1.114.1.4.9.9.1		not-accessible	An FDDI Port entry contains information to assign an FDDI Port to an FDDI Station.
INT swSysSmtFddiPortStationSmtIndex	1.3.6.1.4.1.114.1.4.9.9.1.1	INTEGER	read-only	The index of the SMT instance identified by this entry, relative to this agent.
INT swSysSmtFddiPortStationIndex	1.3.6.1.4.1.114.1.4.9.9.1.2	INTEGER	read-only	The index of the Port instance identified by this entry, relative to the SMT indentified by this entry.
INT swSysSmtFddiPortCurrentStation	1.3.6.1.4.1.114.1.4.9.9.1.3	INTEGER	read-only	Indicates which FDDI station the FDDI Port identified by this entry is assigned to. A value of 0 indicates that the Port is assigned to an external station. Otherwise the value represents the internal backplane station number.
INT swSysSmtFddiPortRequestedStation	1.3.6.1.4.1.114.1.4.9.9.1.4	INTEGER	read-write	Indicates which FDDI station the FDDI port identified by this entry will be set to during the next system reboot. A value of 0 indicates an external station. Otherwise the value represents the internal backplane station number.
INT swSysSmtFddiPortAvailableStations	1.3.6.1.4.1.114.1.4.9.9.1.5	INTEGER	read-only	This value is a sum. Setting of the first bit indicates that the port can be assigned to an external station. Available backplane stations are indicated by adding 2^StationNumber to the sum. Where StationNumber represents a backplane station number.
swSysBridge	1.3.6.1.4.1.114.1.4.10
INT swSysBridgeCount	1.3.6.1.4.1.114.1.4.10.1	INTEGER	read-only	The count of bridges managed by this agent.
swSysBridgeTable	1.3.6.1.4.1.114.1.4.10.2		not-accessible	A list of bridge entries. A single entry exists in this list for each bridge managed by this agent.
swSysBridgeEntry	1.3.6.1.4.1.114.1.4.10.2.1		not-accessible	A bridge entry contains information about a particular bridge managed by this agent.
INT swSysBridgeIndex	1.3.6.1.4.1.114.1.4.10.2.1.1	INTEGER	read-only	The index of the bridge identified by this entry, relative to this agent.
INT swSysBridgePortCount	1.3.6.1.4.1.114.1.4.10.2.1.2	INTEGER	read-only	The number of bridge ports that the bridge identified by this entry controls.
INT swSysBridgeAddressTableSize	1.3.6.1.4.1.114.1.4.10.2.1.3	INTEGER	read-only	The size of the address table for the bridge identified by this entry.
INT swSysBridgeAddressTableCount	1.3.6.1.4.1.114.1.4.10.2.1.4	INTEGER	read-only	The current count of addresses in the address table for the bridge identified by this entry.
INT swSysBridgeAddressTablePeakCount	1.3.6.1.4.1.114.1.4.10.2.1.5	INTEGER	read-only	The peak count of addresses in the address table for the bridge identified by this entry, since the system was last initialized.
INT swSysBridgeAddressThreshold	1.3.6.1.4.1.114.1.4.10.2.1.6	INTEGER	read-write	A reporting threshold for the total number of addresses known for the bridge identified by this entry. When this threshold is reached, the event swSysBridgeAddressThresholdEvent is generated. The range of valid values for setting this object is between 1 and the corresponding value reported by swSysBridgeAddressTableSize + 1 (Note that this range applies to values issued in set requests. The current value may be outside this range, for example if the corresponding value of swSysBridgeMode is changed). Setting this object to one greater than the address table size disables the generation of swSysBridgeAddressThresholdEvents since the limit will never be reached.
INT swSysBridgeMode	1.3.6.1.4.1.114.1.4.10.2.1.7	INTEGER	read-write	The operational mode of the bridge identified by this entry. Note that bridges which report notSupported(3) will not support sets of this object, and that the value notSupported(3) is not a valid value for a set operation.
INT swSysBridgeBackbonePort	1.3.6.1.4.1.114.1.4.10.2.1.8	INTEGER	read-write	The number of the port selected as the backbone segment port when the corresponding value of swSysBridgeMode is is expressMode(1). The value of this object can range from 1 to the corresponding value of swSysBridgePortCount, however, some bridges may support only a subset of ports as backbone ports. If the corresponding value of swSysBridgeMode is not expressMode(1), the value of this object is ignored.
INT swSysBridgeIpFragmentationEnabled	1.3.6.1.4.1.114.1.4.10.2.1.9	INTEGER	read-write	A flag indicating whether or not IP fragmentation is enabled on this bridge. Note that bridges which report notSupported(3) will not support sets of this object, and that the value notSupported(3) is not a valid value for a set operation.
INT swSysBridgeTrFddiTranslationMode	1.3.6.1.4.1.114.1.4.10.2.1.10	INTEGER	read-write	The mode used to describe whether the embedded MAC addresses are byte-conjugated in order to convert them from Token Ring format to native FDDI format (and vice versa), or whether they are left alone (used for traffic flowing across a FDDI backbone to/from Token Ring end stations).
INT swSysBridgeIpxSnapTranslationEnable	1.3.6.1.4.1.114.1.4.10.2.1.13	INTEGER	read-write	This object indicates if the IPX 802.3-FDDI SNAP Translation bridge feature is enabled or disabled. If enabled this value will equal true(1). Note, this object may not be supported on all bridges.
INT swSysBridgeLowLatencyEnable	1.3.6.1.4.1.114.1.4.10.2.1.14	INTEGER	read-write	This object indicates if the bridge low latency feature is enabled or disabled. If enabled this value will equal true(1). Note, this object may not be supported on all bridges.
INT swSysBridgeVlanMode	1.3.6.1.4.1.114.1.4.10.2.1.15	INTEGER	read-write	This object indicates the VLAN types that this bridge will support. Open mode means that each VLAN within this bridge will be of the Open type; all VLANs within this bridge will share the same address table. Closed mode means that each VLAN within this bridge will be of the Closed type; each VLAN within this bridge will have its own address table. Mixed mode means that each VLAN within this bridge with be of either the Open or Closed type; all Open VLANs will share the same address table and each Closed VLAN will have its own address table.
swSysBridgePortTable	1.3.6.1.4.1.114.1.4.10.3		not-accessible	A list of bridge port entries. A single entry exists in this list for each bridge port managed by this agent.
swSysBridgePortEntry	1.3.6.1.4.1.114.1.4.10.3.1		not-accessible	A bridge port entry contains information about a particular bridge port managed by this agent.
INT swSysBridgePortBridgeIndex	1.3.6.1.4.1.114.1.4.10.3.1.1	INTEGER	read-only	The index of the bridge identified by this entry, relative to this agent.
INT swSysBridgePortIndex	1.3.6.1.4.1.114.1.4.10.3.1.2	INTEGER	read-only	The index of the bridge port identified by this entry, within the bridge identified by this entry.
INT swSysBridgePortIfIndex	1.3.6.1.4.1.114.1.4.10.3.1.3	INTEGER	read-only	The value of the MIB-II ifIndex corresponding to the bridge port identified by this entry.
INT swSysBridgePortReceiveMulticastLimit	1.3.6.1.4.1.114.1.4.10.3.1.4	INTEGER	read-write	The maximum number of multicast frames per second that can be received in the sample interval. The sample interval is one second. The default value for this object is zero which implies an infinite rate.
INT swSysBridgePortAddressAction	1.3.6.1.4.1.114.1.4.10.3.1.5	INTEGER	read-write	This object, when read, always returns the value other(1). The behavior of setting this object to each of the acceptable values is as follows: freezeAddress: causes all the learned dynamic addresses to be converted into static addresses. flushAddress: causes all the addresses to be flushed from the address list for the bridge port identified by this entry. flushDynamicAddress: causes all dynamic addresses to be flushed from the address list for the bridge port identified by this entry.
CTR swSysBridgePortSpanningTreeFrameReceivedCounts	1.3.6.1.4.1.114.1.4.10.3.1.6	Counter	read-only	The number of spanning tree frames received by the bridge port identified by this entry.
CTR swSysBridgePortReceiveBlockedDiscards	1.3.6.1.4.1.114.1.4.10.3.1.7	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because the receiving bridge port was not in the 'forwarding' state.
CTR swSysBridgePortReceiveMulticastLimitExceededs	1.3.6.1.4.1.114.1.4.10.3.1.8	Counter	read-only	The number of times the value of swSysBridgePortReceiveMulticastLimit was exceeded for the port identified by this entry.
CTR swSysBridgePortReceiveMulticastLimitExceededDiscards	1.3.6.1.4.1.114.1.4.10.3.1.9	Counter	read-only	The number of multicast/broadcast frames discarded by the bridge port identified by this entry because the corresponding value of swSysBridgePortReceiveMulticastLimit was exceeded.
CTR swSysBridgePortReceiveSecurityDiscards	1.3.6.1.4.1.114.1.4.10.3.1.10	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because they contained source addresses which were statically configured on another bridge port. A statically configured address (station), which is not allowed to move, appears to have moved.
CTR swSysBridgePortReceiveUnknownDiscards	1.3.6.1.4.1.114.1.4.10.3.1.11	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because the destination address was unknown. Note that this counter is only valid for backbone ports, and only when the bridge is operating in express mode.
CTR swSysBridgePortReceiveOtherDiscards	1.3.6.1.4.1.114.1.4.10.3.1.12	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because they contained either invalid (group) source addresses or source addresses belonging to this bridge (indicative of network loops).
CTR swSysBridgePortReceiveErrorDiscards	1.3.6.1.4.1.114.1.4.10.3.1.13	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because of internal bridge system errors (e.g., hardware and software address table discrepencies).
CTR swSysBridgePortSameSegmentDiscards	1.3.6.1.4.1.114.1.4.10.3.1.14	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because the destination address is known on the same network segment as the source address, i.e., the frame does not need to be bridged.
CTR swSysBridgePortTransmitBlockedDiscards	1.3.6.1.4.1.114.1.4.10.3.1.15	Counter	read-only	The number of frames discarded by the bridge port identified by this entry because the transmitting bridge port was not in the 'forwarding' state.
CTR swSysBridgePortReceiveAllPathFilteredFrames	1.3.6.1.4.1.114.1.4.10.3.1.16	Counter	read-only	The number of frames discarded by the bridge port identified by this entry due to user defined receive all path filters.
CTR swSysBridgePortReceiveMulticastPathFilteredFrames	1.3.6.1.4.1.114.1.4.10.3.1.17	Counter	read-only	The number of frames discarded by the bridge port identified by this entry due to user defined receive multicast path filters.
CTR swSysBridgePortTransmitAllPathFilteredFrames	1.3.6.1.4.1.114.1.4.10.3.1.18	Counter	read-only	The number of frames discarded by the bridge port identified by this entry due to user defined transmit all path filters.
CTR swSysBridgePortTransmitMulticastPathFilteredFrames	1.3.6.1.4.1.114.1.4.10.3.1.19	Counter	read-only	The number of frames discarded by the bridge port identified by this entry due to user defined transmit multicast path filters.
CTR swSysBridgePortForwardedUnicastFrames	1.3.6.1.4.1.114.1.4.10.3.1.20	Counter	read-only	The number of unicast frames which this port forwarded to a single destination port.
CTR swSysBridgePortForwardedUnicastOctets	1.3.6.1.4.1.114.1.4.10.3.1.21	Counter	read-only	The number of octets contained in unicast frames which this port forwarded to a single destination port.
CTR swSysBridgePortForwardedMulticastFrames	1.3.6.1.4.1.114.1.4.10.3.1.22	Counter	read-only	The number of multicast frames which this port forwarded.
CTR swSysBridgePortForwardedMulticastOctets	1.3.6.1.4.1.114.1.4.10.3.1.23	Counter	read-only	The number of octets contained in multicast frames which this port forwarded.
CTR swSysBridgePortFloodedUnicastFrames	1.3.6.1.4.1.114.1.4.10.3.1.24	Counter	read-only	The number of unicast frames which this port flooded to all other ports in the bridge.
CTR swSysBridgePortFloodedUnicastOctets	1.3.6.1.4.1.114.1.4.10.3.1.25	Counter	read-only	The number of octets contained in unicast frames which this port flooded to all other ports in the bridge.
INT swSysBridgePortStpMode	1.3.6.1.4.1.114.1.4.10.3.1.26	INTEGER	read-write	The mode of the bridge port.
INT swSysBridgePortReceiveMulticastLimitFrameType	1.3.6.1.4.1.114.1.4.10.3.1.27	INTEGER	read-write	This object identifies the frames type(s) that are to be counted when determining if the receive multicast limit has been exceeded for this bridge port. Devices attached to networks with predominantly high multicast traffic (e.g. video) should set this value to broadcastOnly(2) to detect broadcast storms.
swSysBridgePortAddressTable	1.3.6.1.4.1.114.1.4.10.5		not-accessible	A list of bridge port address information. A single entry exists in this list for each learned address, accross all bridge ports and all bridges managed by this agent.
swSysBridgePortAddressEntry	1.3.6.1.4.1.114.1.4.10.5.1		not-accessible	An bridge port address entry contains information about a particular bridge port address. To create a new entry, set an instance of swSysBridgePortAddressRemoteAddress with the address index portion of the instance set to 0, to a valid value. To remove an entry, set the instance of the swSysBridgePortAddressType for the entry to invalid(2).
INT swSysBridgePortAddressBridgeIndex	1.3.6.1.4.1.114.1.4.10.5.1.1	INTEGER	read-only	The index of the bridge identified by this entry, relative to this agent.
INT swSysBridgePortAddressPortIndex	1.3.6.1.4.1.114.1.4.10.5.1.2	INTEGER	read-only	The index of the bridge port identified by this entry, within the bridge identified by this entry.
INT swSysBridgePortAddressIndex	1.3.6.1.4.1.114.1.4.10.5.1.3	INTEGER	read-only	The index of this address entry within the bridge address table for the bridge identified by this entry. This index ranges from 1 to the corresponding value of swSysBridgeAddressTableSize.
OCT swSysBridgePortAddressRemoteAddress	1.3.6.1.4.1.114.1.4.10.5.1.4	OCTET STRING	read-write	The remote MAC address detected on the bridge port identified by to this entry. Setting this object results in an attempt to create a new entry in the table. Since the value of swSysBridgePortAddressIndex is determined automatically internal to the bridge, a set is only successful if the index value specified for swSysBridgePortAddressIndex is zero. A get-next using the values of swSysBridgePortAddressTypeIndex and swSysBridgePortAddressPortIndex can be used to determine the address index assigned to the newly added address entry.
INT swSysBridgePortAddressType	1.3.6.1.4.1.114.1.4.10.5.1.5	INTEGER	read-write	This object, when read, always returns the value valid(1). Setting this object to invalid(2) will remove the corresponding address entry from the table.
INT swSysBridgePortAddressIsStatic	1.3.6.1.4.1.114.1.4.10.5.1.6	INTEGER	read-write	A value indicating whether this MAC address was statically configured or was dynamically learned. Note that isStatic(1) it the only valid for set operations.
INT swSysBridgePortAddressStaticPort	1.3.6.1.4.1.114.1.4.10.5.1.7	INTEGER	read-only	If the corresponding value of the object swSysBridgePortAddressIsStatic is isStatic(1), this object indicates the local bridge port index (as reported by swSysBridgePortLocalIndex) for which this address MAC was statically configured. If the object swSysBridgePortAddressIsStatic has the value isDynamic(2), the value of this object is 0.
INT swSysBridgePortAddressAge	1.3.6.1.4.1.114.1.4.10.5.1.8	INTEGER	read-only	This object indicates the time, in seconds, elapsed since a packet containing this address as a source was last seen on the bridge port identified by this entry.
OCT swSysBridgeSTPGroupAddress	1.3.6.1.4.1.114.1.4.10.6	OCTET STRING	read-write	Spanning tree bridge group address. The address cannot be changed if the spanning tree is enabled (swSysBridgeStpEnabled). This object can now be found under the swSysBridgeTable as swSysBridgeSTPGroupAddress.
INT swSysBridgeSTPEnable	1.3.6.1.4.1.114.1.4.10.7	INTEGER	read-write	This object indicates if spanning tree bridge feature is enabled or disabled. If enabled this value will equal true(1). This object can now be found under the swSysBridgeTable as swSysBridgeSTPEnable.
swSysIpRouter	1.3.6.1.4.1.114.1.4.11
swSysNetworkMonitor	1.3.6.1.4.1.114.1.4.12
swSysNetworkAnalyzerTable	1.3.6.1.4.1.114.1.4.12.1		not-accessible	A list of analyzer entries. A single entry exists in this list for each bridge port configured for an analyzer.
swSysNetworkAnalyzerTableEntry	1.3.6.1.4.1.114.1.4.12.1.1		not-accessible	An analyzer table entry contains information relating an analyzer port address to the bridge and port index for that analyzer. The effect of creating an entry for a particular port is to configure that port for monitoring. A port which is configured for monitoring is no longer available for switching. To create an entry, set the value of the swSysNetworkAnalyzerStatus object for a non-existent instance to valid(1). The value of the swSysNetworkAnalyzerPhysicalAddress object for the new entry is filled in as a result of the creation. The effect of removing an entry for a particular port is to disable the port for monitoring. The port is then available for switching. To remove an entry, set the value of the corresponding instance of the swSysNetworkAnalyzerStatus object to invalid(2).
INT swSysNetworkAnalyzerBridgeIndex	1.3.6.1.4.1.114.1.4.12.1.1.1	INTEGER	read-only	The index of the bridge relative to this agent where the analyzer identified by this entry is configured.
INT swSysNetworkAnalyzerBridgePortIndex	1.3.6.1.4.1.114.1.4.12.1.1.2	INTEGER	read-only	The index of the port relative to the bridge identified by this entry where the analyzer identified by this entry is configured.
OCT swSysNetworkAnalyzerPhysicalAddress	1.3.6.1.4.1.114.1.4.12.1.1.3	OCTET STRING	read-only	The physical address of the bridge port identified by the corresponding values of swSysNetworkAnalyzerBridgeIndex and swSysNetworkAnayzerBridgePortIndex.
INT swSysNetworkAnalyzerStatus	1.3.6.1.4.1.114.1.4.12.1.1.4	INTEGER	read-write	The status of the entry. Setting the value of a non-existent instance of this object to valid(1) attempts to add the corresponding entry to the table. The effect of adding an entry to the table is to configure the port for monitoring and to disable it for switching. Setting an existing instance of this object to invalid(2) attempts to remove the corresponding entry from the table. The effect of removing an entry from the table is to disable the port for monitoring and to make available for switching.
swSysNetworkPortMonitorTable	1.3.6.1.4.1.114.1.4.12.2		not-accessible	A list of monitor port entries. A single entry exists in this for each bridge port being monitored.
swSysNetworkPortMonitorTableEntry	1.3.6.1.4.1.114.1.4.12.2.1		not-accessible	A port monitor table entry contains information relating a bridge port being monitored with the address of the analyzer which is being used to monitor the port. The effect of creating an entry for a particular port is to enable monitoring of that port by the analyzer specified. To create an entry, set the value of the swSysNetworkPortMonitorAnalyzerAddress object to the address of the network analyzer port. This value should be the same as the value of the swSysNetworkAnalyzerPhysicalAddress object for the analyzer. The effect of removing an entry for a particular port is to disable monitoring of that port. To remove an entry, set the value of the corresponding instance of the swSysNetworkPortMonitorStatus object to invalid(2).
INT swSysNetworkPortMonitorBridgeIndex	1.3.6.1.4.1.114.1.4.12.2.1.1	INTEGER	read-only	The index of the bridge relative to this agent where the monitored port identified by this entry is located.
INT swSysNetworkPortMonitorBridgePortIndex	1.3.6.1.4.1.114.1.4.12.2.1.2	INTEGER	read-only	The index of the port which is being monitored relative to the bridge identified by this entry.
OCT swSysNetworkPortMonitorAnalyzerAddress	1.3.6.1.4.1.114.1.4.12.2.1.3	OCTET STRING	read-write	The physical address of the port where the analyzer, which is monitoring the port identified by this entry, is located. Setting the value of a non-existent instance of this object attempts to add an entry to the table. The effect of adding an entry to the table is to enable monitoring of the port by the analyzer specified. Setting the value of an existing instance of this object will switch the monitored port to the new analyzer address.
INT swSysNetworkPortMonitorStatus	1.3.6.1.4.1.114.1.4.12.2.1.4	INTEGER	read-write	The status of the entry. Setting an existing instance of this object to invalid(2) attempts to remove the corresponding entry from the table. The effect of removing an entry from the table is to disable monitoring of the port.
swSysTokenRingPort	1.3.6.1.4.1.114.1.4.13
INT swSysTokenRingPortCount	1.3.6.1.4.1.114.1.4.13.1	INTEGER	read-only	The count of token ring ports managed by this agent.
swSysTokenRingPortTable	1.3.6.1.4.1.114.1.4.13.2		not-accessible	A list of token ring port entries. A single entry exists in this list for each token ring port managed by this agent.
swSysTokenRingPortEntry	1.3.6.1.4.1.114.1.4.13.2.1		not-accessible	A token ring port entry contains information about a particular token ring port managed by this agent.
INT swSysTokenRingPortIndex	1.3.6.1.4.1.114.1.4.13.2.1.1	INTEGER	read-only	The index of the token ring port identified by this entry, relative to this agent.
INT swSysTokenRingPortIfIndex	1.3.6.1.4.1.114.1.4.13.2.1.2	INTEGER	read-only	The value of the MIB-II ifIndex corresponding to the token ring port identified by this entry.
STR swSysTokenRingPortLabel	1.3.6.1.4.1.114.1.4.13.2.1.3	DisplayString	read-write	An ASCII text string describing the token ring port identified by this entry.
INT swSysTokenRingPortInsertStatus	1.3.6.1.4.1.114.1.4.13.2.1.4	INTEGER	read-only	The current value of the link status for the token ring port identified by this entry.
INT swSysTokenRingPortType	1.3.6.1.4.1.114.1.4.13.2.1.5	INTEGER	read-only	Specific port type description for the token ring port identified by this entry.
INT swSysTokenRingPortMode	1.3.6.1.4.1.114.1.4.13.2.1.6	INTEGER	read-write	The current mode of the port. The default mode (station) is used to connect a hub to the port. Lobe mode is used to direct connect a Token Ring station into the port. This selection can only be made on ports 1 and 2 of the module.
INT swSysTokenRingPortSpeed	1.3.6.1.4.1.114.1.4.13.2.1.7	INTEGER	read-write	The current speed of the port. The default speed is sixteenMegabit.
CTR swSysTokenRingPortLineErrors	1.3.6.1.4.1.114.1.4.13.2.1.8	Counter	read-only	This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame.
CTR swSysTokenRingPortBurstErrors	1.3.6.1.4.1.114.1.4.13.2.1.9	Counter	read-only	This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error).
CTR swSysTokenRingPortACErrors	1.3.6.1.4.1.114.1.4.13.2.1.10	Counter	read-only	This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly.
CTR swSysTokenRingPortAbortTransErrors	1.3.6.1.4.1.114.1.4.13.2.1.11	Counter	read-only	This counter is incremented when a station transmits an abort delimiter while transmitting.
CTR swSysTokenRingPortInternalErrors	1.3.6.1.4.1.114.1.4.13.2.1.12	Counter	read-only	This counter is incremented when a station recognizes an internal error.
CTR swSysTokenRingPortLostFrameErrors	1.3.6.1.4.1.114.1.4.13.2.1.13	Counter	read-only	This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip mode does not receive the trailer of the frame before the TRR timer goes off.
CTR swSysTokenRingPortReceiveCongestionErrors	1.3.6.1.4.1.114.1.4.13.2.1.14	Counter	read-only	This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested.
CTR swSysTokenRingPortFrameCopiedErrors	1.3.6.1.4.1.114.1.4.13.2.1.15	Counter	read-only	This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a possible line hit or duplicate address.
CTR swSysTokenRingPortTokenErrors	1.3.6.1.4.1.114.1.4.13.2.1.16	Counter	read-only	This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted.
CTR swSysTokenRingPortSoftErrors	1.3.6.1.4.1.114.1.4.13.2.1.17	Counter	read-only	The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Soft Errors are those which are recoverable by the MAC layer protocols.
CTR swSysTokenRingPortHardErrors	1.3.6.1.4.1.114.1.4.13.2.1.18	Counter	read-only	The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or receiving beacon MAC frames.
CTR swSysTokenRingPortTransmitBeacons	1.3.6.1.4.1.114.1.4.13.2.1.19	Counter	read-only	The number of times this interface has transmitted a beacon frame.
CTR swSysTokenRingPortLobeWires	1.3.6.1.4.1.114.1.4.13.2.1.20	Counter	read-only	The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed when this condition occurs.
CTR swSysTokenRingPortRemoves	1.3.6.1.4.1.114.1.4.13.2.1.21	Counter	read-only	The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state.
CTR swSysTokenRingPortSingles	1.3.6.1.4.1.114.1.4.13.2.1.22	Counter	read-only	The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if there is a hardware problem.
CTR swSysTokenRingPortFreqErrors	1.3.6.1.4.1.114.1.4.13.2.1.23	Counter	read-only	The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency.
INT swSysTokenRingPortRingStatus	1.3.6.1.4.1.114.1.4.13.2.1.24	INTEGER	read-only	The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station has successfully been added to the ring. Before an open is completed, this object has the value for the 'no status' condition. This object is useful for debugging problems when the station can not even enter the ring. The object's value is a sum of values, one for each currently applicable condition. The following values are defined for various conditions: 0 = No Problems detected 32 = Ring Recovery 64 = Single Station 256 = Remove Received 512 = reserved 1024 = Auto-Removal Error 2048 = Lobe Wire Fault 4096 = Transmit Beacon 8192 = Soft Error 16384 = Hard Error 32768 = Signal Loss 131072 = no status, open not completed.
swSysFtGroup	1.3.6.1.4.1.114.1.4.14
swSysFtTable	1.3.6.1.4.1.114.1.4.14.1		not-accessible	A list of entries which describe file transfers.
swSysFtTableEntry	1.3.6.1.4.1.114.1.4.14.1.1		not-accessible	A description of a particular file transfer entry.
INT swSysFtIndex	1.3.6.1.4.1.114.1.4.14.1.1.1	INTEGER	read-only	A unique index used to identifying this entry.
INT swSysFtDirection	1.3.6.1.4.1.114.1.4.14.1.1.2	INTEGER	read-write	Specifies the direction of the file transfer.
SWS swSysFtLocalStorageType	1.3.6.1.4.1.114.1.4.14.1.1.3	SwSysStorageType	read-write	The type of storage on the local system to be used as the source/destination for the file transfer.
SWS swSysFtLocalResourceType	1.3.6.1.4.1.114.1.4.14.1.1.4	SwSysResourceType	read-write	The type of resource on the local system to be used as the source/destination for the file transfer.
SWS swSysFtLocalResourceMask	1.3.6.1.4.1.114.1.4.14.1.1.5	SwSysResourceBitMask	read-write	The indices of the resources on the local system to be used as the source/destination for the file transfer. The type of resource to which these indices apply is specified by the corresponding value of swSysFtLocalResourceType. If resourceBridge is used, swSysFtLocalResourceMask indicates the bridge slot number the filter code will be downloaded. For instance, swSysFtLocalResourceMask value of 0x03 indicates bridge slot number 1 and 2.
OID swSysFtLocalResourceAttribute	1.3.6.1.4.1.114.1.4.14.1.1.6	OBJECT IDENTIFIER	read-write	An identifier which specifies the particular resource attribute on the local system which is the source/destination of the file transfer. The resource(s) to which this attribute applies is specified by the corresponding values of swSysFtLocalResourceType and swSysFtLocalResourceMask.
ADR swSysFtRemoteAddressType	1.3.6.1.4.1.114.1.4.14.1.1.7	SwSysAddressType	read-write	The type of address which is specified by the corresponding value of swSysFtRemoteAddress.
OCT swSysFtRemoteAddress	1.3.6.1.4.1.114.1.4.14.1.1.8	OCTET STRING	read-write	The address of the source/destination file on the remote system.
STR swSysFtRemoteFileName	1.3.6.1.4.1.114.1.4.14.1.1.9	DisplayString	read-write	The full path name of the source/destination file on the remote system.
STR swSysFtRemoteUserName	1.3.6.1.4.1.114.1.4.14.1.1.10	DisplayString	read-write	The user name to be used when requesting the file transfer to/from the remote system.
OCT swSysFtRemoteUserPassword	1.3.6.1.4.1.114.1.4.14.1.1.11	OCTET STRING	read-write	The password to be used when requesting the file transfer to/from the remote system. When read, this object returns a zero length string. Note that, for security reasons, some ftp servers may insist on a non-zero length user password.
INT swSysFtForceTransfer	1.3.6.1.4.1.114.1.4.14.1.1.12	INTEGER	read-write	Setting this object to true makes the agent ignore non-fatal (i.e. version/id mismatch) errors encountered during a file transfer request.
CTR swSysFtBytesTransferred	1.3.6.1.4.1.114.1.4.14.1.1.13	Counter	read-only	The number of bytes successfully transferred.
INT swSysFtStatus	1.3.6.1.4.1.114.1.4.14.1.1.14	INTEGER	read-only	The status of the file transfer.
OID swSysFtDetailedStatus	1.3.6.1.4.1.114.1.4.14.1.1.15	OBJECT IDENTIFIER	read-only	Detailed status for the transfer for the particular local resource attribute specified by the corresponding values of swSysFtLocalStorageType, swSysFtLocalResourceType, swSysFtLocalResourceMask, and swSysFtLocalResourceAttribute. Note that this object is only valid in the case where swSysFtStatus indicates an error.
STR swSysFtDetailedStatusString	1.3.6.1.4.1.114.1.4.14.1.1.16	DisplayString	read-only	Detailed status description for the requested transfer.
STR swSysFtOwnerString	1.3.6.1.4.1.114.1.4.14.1.1.17	DisplayString	read-write	A string describing the creator/owner of this entry.
ROW swSysFtRowStatus	1.3.6.1.4.1.114.1.4.14.1.1.18	RowStatus	read-write	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) is not allowed. Setting this object to createAndWait(5) causes an entry to be created with swSysFtRowStatus value of notReady(3). Setting this object to active(1) causes the transfer to start for the given row. Objects within the row cannot be modified once a row has been set to active(1), Setting this object to destroy(6) causes the corresponding row to be deleted. Note that a request to set a row to notInService(2) or destroy(6) will fail if the current rowStatus value is active(1) (i.e. a file transfer is currently in progress). This is necessary since aborting a file transfer may leave the system in an inconsistent state. Note that, currently, only a single instance of a row can be created in this table.
swSysFtResourceAttributes	1.3.6.1.4.1.114.1.4.14.2
swSysFtSystemAttributes	1.3.6.1.4.1.114.1.4.14.2.1
swSysFtSystemOperationalCode	1.3.6.1.4.1.114.1.4.14.2.1.1
swSysFtSystemConfiguration	1.3.6.1.4.1.114.1.4.14.2.1.2
swSysFtSystemBridgeFilterCode	1.3.6.1.4.1.114.1.4.14.2.1.3
swSysFtDetailedResourceStatus	1.3.6.1.4.1.114.1.4.14.3
swSysFtSystemDetailedStatus	1.3.6.1.4.1.114.1.4.14.3.1
swSysFtSysStatusNotApplicable	1.3.6.1.4.1.114.1.4.14.3.1.1
swSysFtSysStatusNoImageLabel	1.3.6.1.4.1.114.1.4.14.3.1.2
swSysFtSysStatusConfigIdMismatch	1.3.6.1.4.1.114.1.4.14.3.1.3
swSysFtSysStatusChecksumError	1.3.6.1.4.1.114.1.4.14.3.1.4
swSysFtSysStatusNvRamError	1.3.6.1.4.1.114.1.4.14.3.1.5
swSysFtSysStatusFlashError	1.3.6.1.4.1.114.1.4.14.3.1.6
swSysFtSysStatusNoRoom	1.3.6.1.4.1.114.1.4.14.3.1.7
swSysFtSysBridgeFilterNotApplicable	1.3.6.1.4.1.114.1.4.14.3.1.8
swSysFtSysBridgeFilterSyntaxError	1.3.6.1.4.1.114.1.4.14.3.1.9
swSysFtSysBridgeFilterdownloadError	1.3.6.1.4.1.114.1.4.14.3.1.10
swSysFtSysBridgeFilterNoRoom	1.3.6.1.4.1.114.1.4.14.3.1.11
swSysIpGroup	1.3.6.1.4.1.114.1.4.15
swSysIpBaseGroup	1.3.6.1.4.1.114.1.4.15.1
swSysIpInterfaceGroup	1.3.6.1.4.1.114.1.4.15.2
INT swSysIpInterfaceCount	1.3.6.1.4.1.114.1.4.15.2.1	INTEGER	read-only	A count of the total number of IP interfaces configured.
swSysIpInterfaceTable	1.3.6.1.4.1.114.1.4.15.2.2		not-accessible	A list of configured IP interfaces.
swSysIpInterfaceEntry	1.3.6.1.4.1.114.1.4.15.2.2.1		not-accessible	An individual IP interface.
INT swSysIpInterfaceIpStackIndex	1.3.6.1.4.1.114.1.4.15.2.2.1.1	INTEGER	read-only	The index of the IP stack identified by this entry relative to this agent.
IP swSysIpInterfaceAddr	1.3.6.1.4.1.114.1.4.15.2.2.1.2	IpAddress	read-only	The IP address of this entry within the IP stack identified within this entry.
IP swSysIpInterfaceNetMask	1.3.6.1.4.1.114.1.4.15.2.2.1.3	IpAddress	read-only	The subnet mask associated with this IP interface. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
INT swSysIpInterfaceIndex	1.3.6.1.4.1.114.1.4.15.2.2.1.4	INTEGER	read-write	The index value which uniquely identifies the interface to which this entry is applicable. lspIPInterfaceIndex maps to the same interface as identified by ifIndex in the ifTable. Currently, this object can not be modified after creation.
INT swSysIpInterfaceBcastAddr	1.3.6.1.4.1.114.1.4.15.2.2.1.5	INTEGER	read-write	This object represents the value of the least significant bit of this entry's direct broadcast address. For example, a value of one signifies that the host portion of the broadcast address is set to all ones.
INT swSysIpInterfaceCost	1.3.6.1.4.1.114.1.4.15.2.2.1.6	INTEGER	read-write	The route cost metric used for this entry.
ROW swSysIpInterfaceStatus	1.3.6.1.4.1.114.1.4.15.2.2.1.7	RowStatus	read-write	The status column for this IP interface. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the object in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available the agent will reject the request. Other objects in this row entry can be individually modified while the row status is active(1). Setting this object to destroy(6) will remove this entry.
swSysIpxGroup	1.3.6.1.4.1.114.1.4.16
swSysIpxBaseGroup	1.3.6.1.4.1.114.1.4.16.1
swSysIpxInterfaceGroup	1.3.6.1.4.1.114.1.4.16.2
INT swSysIpxInterfaceCount	1.3.6.1.4.1.114.1.4.16.2.1	INTEGER	read-only	A count of the total number of IPX interfaces configured.
swSysIpxInterfaceTable	1.3.6.1.4.1.114.1.4.16.2.2		not-accessible	A list of configured IPX interfaces.
swSysIpxInterfaceEntry	1.3.6.1.4.1.114.1.4.16.2.2.1		not-accessible	An individual IPX interface.
INT swSysIpxInterfaceIpxStackIndex	1.3.6.1.4.1.114.1.4.16.2.2.1.1	INTEGER	read-only	The index of the IPX stack identified by this entry relative to this agent.
IPX swSysIpxInterfaceNetNumber	1.3.6.1.4.1.114.1.4.16.2.2.1.2	IpxNetworkNumber	read-only	The IPX Network Number of this entry.
INT swSysIpxInterfaceIfIndex	1.3.6.1.4.1.114.1.4.16.2.2.1.3	INTEGER	read-write	The ifIndex of the virtual interface that this IPX interface is is configured over. The swSysIpxInterfaceIfIndex identifies a virtual interface, for example a VLAN, that this local address is associated with for purposes of routing or network management.
INT swSysIpxInterfaceCost	1.3.6.1.4.1.114.1.4.16.2.2.1.4	INTEGER	read-write	The cost associated with the IPX address of this entry.
INT swSysIpxInterfaceFrameType	1.3.6.1.4.1.114.1.4.16.2.2.1.5	INTEGER	read-write	The frame format used for routing frames on this IPX interface. The framing formats are for ethernet ports. There are two frame formats for FDDI ports: 802.2 and FDDI SNAP. The correct FDDI format is automatically chosen if this interface is associated with a VLAN interface that contains both ethernet and FDDI ports. If the VLAN interface is an FDDI port, than the only values that can be written to this object are: frame-802-2(2) and frame-SNAP(4).
ROW swSysIpxInterfaceStatus	1.3.6.1.4.1.114.1.4.16.2.2.1.6	RowStatus	read-write	The status column for this IPX interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object ot createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the object in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available the agent will reject the request. Other objects in this row entry can be individually modified while the row status is active(1). Setting this object to destroy(6) will remove this entry.
swSysAppleTalkGroup	1.3.6.1.4.1.114.1.4.17
swSysAppleTalkBaseGroup	1.3.6.1.4.1.114.1.4.17.1
swSysAppleTalkInterfaceGroup	1.3.6.1.4.1.114.1.4.17.2
INT swSysAtInterfaceCount	1.3.6.1.4.1.114.1.4.17.2.1	INTEGER	read-only	A count of the total number of AppleTalk interfaces configured.
swSysAtInterfaceTable	1.3.6.1.4.1.114.1.4.17.2.2		not-accessible	A list of AppleTalk ports for this entity.
swSysAtInterfaceEntry	1.3.6.1.4.1.114.1.4.17.2.2.1		not-accessible	An individual appletalk interface entry. Appletalk entries with row status of active(1) cannot be modified but must set to destroy(6) and recreated.
INT swSysAtInterfaceAtStackIndex	1.3.6.1.4.1.114.1.4.17.2.2.1.1	INTEGER	read-write	The index of the Appletalk stack identified by this entry relative to this agent. Setting of this object is required for all interface creations.
ADR swSysAtInterfaceNetAddress	1.3.6.1.4.1.114.1.4.17.2.2.1.2	DdpNodeAddress	read-only	The AppleTalk network address configured for this port.
INT swSysAtInterfaceType	1.3.6.1.4.1.114.1.4.17.2.2.1.3	INTEGER	read-write	The type of interface that is configured for this port. Setting of this object is required for all interface creations.
ATN swSysAtInterfaceNetStart	1.3.6.1.4.1.114.1.4.17.2.2.1.4	ATNetworkNumber	read-write	The first AppleTalk network address in the range configured for this port. If this port is not a native AppleTalk port, this object shall have the value of two octets of zero. Setting of this object is mandatory only for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceNetEnd	1.3.6.1.4.1.114.1.4.17.2.2.1.5	ATNetworkNumber	read-write	The last AppleTalk network address in the range configured for this port. If the network to which this AppleTalk port is connected is a non-extended network, or if it is not a native AppleTalk port, the value for swSysAtInterfaceNetEnd shall be two octets of zero. Setting of this object is mandatory only for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZoneDefault	1.3.6.1.4.1.114.1.4.17.2.2.1.6	ATName	read-write	The name of the default zone for this port. If this port only has one zone, that zone is represented here. Setting of this object is mandatory for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone1	1.3.6.1.4.1.114.1.4.17.2.2.1.7	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone2	1.3.6.1.4.1.114.1.4.17.2.2.1.8	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone3	1.3.6.1.4.1.114.1.4.17.2.2.1.9	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone4	1.3.6.1.4.1.114.1.4.17.2.2.1.10	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone5	1.3.6.1.4.1.114.1.4.17.2.2.1.11	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone6	1.3.6.1.4.1.114.1.4.17.2.2.1.12	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone7	1.3.6.1.4.1.114.1.4.17.2.2.1.13	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone8	1.3.6.1.4.1.114.1.4.17.2.2.1.14	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone9	1.3.6.1.4.1.114.1.4.17.2.2.1.15	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone10	1.3.6.1.4.1.114.1.4.17.2.2.1.16	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone11	1.3.6.1.4.1.114.1.4.17.2.2.1.17	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone12	1.3.6.1.4.1.114.1.4.17.2.2.1.18	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone13	1.3.6.1.4.1.114.1.4.17.2.2.1.19	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone14	1.3.6.1.4.1.114.1.4.17.2.2.1.20	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
ATN swSysAtInterfaceZone15	1.3.6.1.4.1.114.1.4.17.2.2.1.21	ATName	read-write	Zone name in this entry's zone list. This object may only only be set for interfaces with swSysAtInterfaceType equal to seedInterface(1).
INT swSysAtInterfaceIfIndex	1.3.6.1.4.1.114.1.4.17.2.2.1.22	INTEGER	read-write	The interface associated with this AppleTalk port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the ifTable. Setting of this object is required for all interface creations.
INT swSysAtInterfaceState	1.3.6.1.4.1.114.1.4.17.2.2.1.23	INTEGER	read-only	The current state of the appletalk interface.
ROW swSysAtInterfaceStatus	1.3.6.1.4.1.114.1.4.17.2.2.1.24	RowStatus	read-write	The status column for this IP interface. This object can be set to: createAndGo(4) createAndWait(5) destroy(6) The following value may be read: active(1) notInService(2) Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the object in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available the agent will reject the request. Setting this object to createAndWait(5) causes the agent to create an entry which has the value notInService(2). Only three notInService(2) entries are permitted at any one time. Setting a row with status notInService(2) to active(1) will cause this entry to change to active(1) if the appropriate columns have been set. Setting this object to destroy(6) will remove this entry.
swSysModuleCardGroup	1.3.6.1.4.1.114.1.4.18
INT swSysModuleCardCount	1.3.6.1.4.1.114.1.4.18.1	INTEGER	read-only	The current count of module components present in the system.
swSysModuleCardInfoTable	1.3.6.1.4.1.114.1.4.18.2		not-accessible	A list of module card information entries. A single entry exists in this list for each modular component in the system.
swSysModuleCardInfoEntry	1.3.6.1.4.1.114.1.4.18.2.1		not-accessible	A module card info entry contains information about a particular modular component within the system.
INT swSysModuleCardInfoIndex	1.3.6.1.4.1.114.1.4.18.2.1.1	INTEGER	read-only	The index of the modular component identified by this entry.
INT swSysModuleCardInfoFamily	1.3.6.1.4.1.114.1.4.18.2.1.2	INTEGER	read-only	The family code for this module.
INT swSysModuleCardInfoGenericType	1.3.6.1.4.1.114.1.4.18.2.1.3	INTEGER	read-only	The generic type code for this module.
INT swSysModuleCardInfoSpecificType	1.3.6.1.4.1.114.1.4.18.2.1.4	INTEGER	read-only	The specific type code for this module.
STR swSysModuleCardInfoPartNumber	1.3.6.1.4.1.114.1.4.18.2.1.5	DisplayString	read-only	The specific part number for this module.
STR swSysModuleCardInfoManufacturingDate	1.3.6.1.4.1.114.1.4.18.2.1.6	DisplayString	read-only	The date that this module was manufactured in the format mm/dd/yyyy.
STR swSysModuleCardInfoModuleSerialNumber	1.3.6.1.4.1.114.1.4.18.2.1.7	DisplayString	read-only	3Com serial number.
STR swSysModuleCardInfoTLASerialNumber	1.3.6.1.4.1.114.1.4.18.2.1.8	DisplayString	read-only	TOP level assembly serial number for boards with non-removable daughter cards. Null string for all other board types.
STR swSysModuleCardInfo3CNumber	1.3.6.1.4.1.114.1.4.18.2.1.9	DisplayString	read-only	On a backplane or non-removable module this is the 3C number of the chassis. On a removable module this is the 3C number of the module.
INT swSysModuleCardInfoICTTestStatus	1.3.6.1.4.1.114.1.4.18.2.1.10	INTEGER	read-only	1 equals test passed, or greater than 1 identifies the test number failure (0 or FF indicates field yet not written).
STR swSysModuleCardInfoICTTestRevision	1.3.6.1.4.1.114.1.4.18.2.1.11	DisplayString	read-only	Manufacturing ATE test revision number (XX.XX).
INT swSysModuleCardInfoSystemTestStatus	1.3.6.1.4.1.114.1.4.18.2.1.12	INTEGER	read-only	1 equals test passed, or greater than 1 identifies the test number failure (0 or FF indicates field yet not written).
INT swSysModuleCardInfoFunctionalTestStatus	1.3.6.1.4.1.114.1.4.18.2.1.13	INTEGER	read-only	1 equals test passed, or greater than 1 identifies the test number failure (0 or FF indicates field yet not written).
STR swSysModuleCardInfoFunctionalTestRevision	1.3.6.1.4.1.114.1.4.18.2.1.14	DisplayString	read-only	Manufacturing functional test revision number (XX.XX).
STR swSysModuleCardInfoBoardRevision	1.3.6.1.4.1.114.1.4.18.2.1.15	DisplayString	read-only	Board revision code.
INT swSysModuleCardInfoRuntimeHours	1.3.6.1.4.1.114.1.4.18.2.1.16	INTEGER	read-only	A total count of the number of hours this module has been in operation.
swSysDiagnosticsGroup	1.3.6.1.4.1.114.1.4.19
swSysDiagnosticsInfoTable	1.3.6.1.4.1.114.1.4.19.1		not-accessible	A list of module card information entries. A single entry exists in this list for each modular component in the system.
swSysDiagnosticsInfoEntry	1.3.6.1.4.1.114.1.4.19.1.1		not-accessible	A diagnostics info entry contains information about a particular diagnostics event on a modular component within the system.
INT swSysDiagnosticsInfoIndex	1.3.6.1.4.1.114.1.4.19.1.1.1	INTEGER	read-only	The index of the diagnostics modular component identified by this entry.
STR swSysDiagnosticsInfoPOVDiagnosticsRevision	1.3.6.1.4.1.114.1.4.19.1.1.2	DisplayString	read-only	The revision of the POV (power on verification) diagnostics software at the most recent failure.
STR swSysDiagnosticsInfoExtendedDiagnosticsRevision	1.3.6.1.4.1.114.1.4.19.1.1.3	DisplayString	read-only	The revision of the extended diagnostics software at the most recent failure.
STR swSysDiagnosticsInfoDiagnosticFailureCode	1.3.6.1.4.1.114.1.4.19.1.1.4	DisplayString	read-only	The code written by the diagnostics at the most recent failure. This identifies both the test number and failure code in the following format: -. If there is no failure then 000-000 is displayed.
STR swSysDiagnosticsInfoDiagnosticFailureDateTime	1.3.6.1.4.1.114.1.4.19.1.1.5	DisplayString	read-only	The date and time of the most recent diagnostic failure for the module.
INT swSysDiagnosticsInfoDiagnosticFailureSlotNumber	1.3.6.1.4.1.114.1.4.19.1.1.6	INTEGER	read-only	The slot number (network adapter cards only) of the most recent diagnostic failure for the module.
INT swSysDiagnosticsInfoDiagnosticFailureCounter	1.3.6.1.4.1.114.1.4.19.1.1.7	INTEGER	read-only	The total number of diagnostic failures logged against this module.
INT swSysDiagnosticsInfoDiagnosticFieldDOACounter	1.3.6.1.4.1.114.1.4.19.1.1.8	INTEGER	read-only	The total number of failures occurring at this module during the first 48 hours of operation.
corebuilderSystemsMib	1.3.6.1.4.1.114.1.5
superstackSystemsMib	1.3.6.1.4.1.114.1.6
switchingSystemsFddiMib	1.3.6.1.4.1.114.1.10
switchingSystemsProducts	1.3.6.1.4.1.114.2
corebuilderProductsII	1.3.6.1.4.1.114.2.1
superstackProducts	1.3.6.1.4.1.114.2.2

RFC description

3Com Switching Systems MIB managing bridge VLAN modes, system types, and resource configuration.

Start monitoring Synernetics managed switching system, legacy (hardware/software identity status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SWITCHING-SYSTEMS-MIB

What Is SWITCHING-SYSTEMS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description