SW-COMMON-MIB

All MIBs › SW-COMMON-MIB

Category: Switch Management - D-Link

Description: Defines common switch management objects and shared base structures for D-Link switch platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SW-COMMON-MIB?

This is a D-Link enterprise MIB providing common/shared object definitions, textual conventions, and base structures used across D-Link's family of managed switch MIB modules. It does not itself expose device counters or status; instead it centralizes shared type definitions and index conventions that other D-Link switch-specific MIBs, such as per-model port, VLAN, or QoS MIBs, import to stay consistent. Because it is a foundational/common module, it carries no direct monitorable hardware or software status objects like uptime, temperature, or CPU load; those are exposed in the switch-specific MIBs built on top of it. Nearly all other D-Link switch product MIB modules depend on this common module for shared definitions. It is deployed alongside D-Link managed Ethernet switch product MIB packages, loaded as a prerequisite whenever a D-Link switch-specific MIB is compiled or used for SNMP monitoring. Engineers can download the SW-COMMON-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SW-COMMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link ES2000 'Golf' series managed switch (Marconi enterprise OID branding)

Monitoring Examples

No sample objects were provided for this module, consistent with it being a common/base MIB with no data objects of its own; the concrete monitorable counters live in the D-Link switch-model-specific MIBs that import definitions from this module, so no monitoring scenario can be given honestly here.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

enterprises

OIDs

OID symbolic	OID numeric	Type	Access	Description
marconi	1.3.6.1.4.1.326
systems	1.3.6.1.4.1.326.2
external	1.3.6.1.4.1.326.2.20
dlink	1.3.6.1.4.1.326.2.20.1
dlinkcommon	1.3.6.1.4.1.326.2.20.1.1
golf	1.3.6.1.4.1.326.2.20.1.2
golfproducts	1.3.6.1.4.1.326.2.20.1.2.1
es2000	1.3.6.1.4.1.326.2.20.1.2.1.3
golfcommon	1.3.6.1.4.1.326.2.20.1.2.2
marconi_mgmt	1.3.6.1.4.1.326.2.20.1.2.2.2
es2000Mgmt	1.3.6.1.4.1.326.2.20.1.2.2.2.28
swL2Mgmt	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2
swL2DevMgmt	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1
swL2DevCtrl	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1
INT swL2DevCtrlStpState	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.1	INTEGER	read-write	This object can be enabled or disabled spanning tree algorithm during runtime of the system.
INT swL2DevCtrlPartitionModeState	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.2	INTEGER	read-write	This object used to enable or disable port auto partition. When the object apply for all ports of the device.
INT swL2DevCtrlTableLockState	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.3	INTEGER	read-write	This object indicates whether the address table is locked. In other words, the address table doesn't learn any more new address. The aging timer is suspended when the address table is locked. As long as the table is locked, all of the frames are dropped if the destination can not be found in the address.
INT swL2DevCtrlHOLState	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.4	INTEGER	read-write	The object provides a way to prevent HOL (Head Of Line) blocking between ports. HOL protection may prevent forwarding a packet to a blocking port. The idea relies on the assumption that it is better to discard packets destined to blocking ports, then to let them consume more and more buffers in the input-port's Rx-counters because eventually these input ports may become totally blocked. The meanings of the values are: other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - HOL function disable for device. enabled(3) - HOL function enable for device.
INT swL2DevCtrlAddrLookupModesAndHitRate	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.5	INTEGER	read-write	According to the differnet address looke mode setting, to enlarge the address table size is possible in device. But there is side effect as the higher level you have, the lower thorughput device has. That means Level 0 get the smallest table size, but get better performace. We recommand the user use the Level 1 as defualt setting.
INT swL2DevCtrlBuzzerState	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.6	INTEGER	read-write	Controls buzzer state to be disabled or enabled.
INT swL2DevCtrlBuzzerTest	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.7	INTEGER	write-only	Tests buzzer to bibi. First of all, any unsigned integer can be used to set.
swL2DevAlarm	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2
INT swL2DevAlarmPartition	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.1	INTEGER	read-write	Depending on this object, the device send a trap or not when any one of the device's ports was partitioned.
INT swL2DevAlarmNewRoot	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.2	INTEGER	read-write	When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
INT swL2DevAlarmTopChange	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.3	INTEGER	read-write	This object determines to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
INT swL2DevAlarmLinkChange	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.4	INTEGER	read-write	This object determines to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
swL2DevAlarmPowerTable	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5		not-accessible	A table that controls error state to bibi about power module.
swL2DevAlarmPowerEntry	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1		not-accessible	A list of controlling informations for power module.
INT swL2DevAlarmPowerIndex	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.1	INTEGER	read-only	ID of the power module.
INT swL2DevAlarmPowerTemperature	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.2	INTEGER	read-write	Controls temperature error state in power module.
INT swL2DevAlarmPowerVolt	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.3	INTEGER	read-write	Controls volt error state in power module.
INT swL2DevAlarmPowerCurrent	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.4	INTEGER	read-write	Controls current error state in power module.
INT swL2DevAlarmPowerFan	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.5	INTEGER	read-write	Controls fan error state in power module.
swL2DevAlarmSystemFanTable	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6		not-accessible	A table that controls error state to bibi about system fans.
swL2DevAlarmSystemFanEntry	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6.1		not-accessible	A list of controlling informations for system fans.
INT swL2DevAlarmSystemFanIndex	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6.1.1	INTEGER	read-only	ID of the system fans.
INT swL2DevAlarmSystemFanState	1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6.1.2	INTEGER	read-write	Controls system fan error state.

RFC description

Vendor-private MIB for Brocade switch common management and Fibre Channel port configuration.

Start monitoring D-Link ES2000 'Golf' series switch (Marconi-branded OEM, shared object definitions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SW-COMMON-MIB

What Is SW-COMMON-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description