SUN-SNMP

All MIBs › SUN-SNMP

Description: SUN-SNMP module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SUN-SNMP?

SUN-SNMP is a Sun Microsystems foundational module, most likely defining shared textual conventions, imports, or enterprise OID anchors used by other Sun-specific MIBs rather than exposing its own runtime data. No short description, module description, or sample objects were provided, so its exact scope cannot be confirmed beyond this structural role. As such it has essentially no direct hardware/software status data of its own to monitor; its value is indirect, underpinning other Sun MIBs that build on its definitions. It is foundational to the broader family of legacy Sun/Solaris enterprise MIBs. It would be encountered on Sun/Solaris systems alongside other Sun-branded MIB modules that import from it. Engineers can download the SUN-SNMP file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SUN-SNMP. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral base definitions module
Sun/Solaris SNMP agent host

Monitoring Examples

This module appears to be a definitions/imports module rather than one exposing runtime data objects, and no sample objects were supplied to confirm otherwise, so no concrete monitoring scenario can be honestly described. Its practical role, if confirmed, would be limited to supplying shared type/OID definitions consumed by other Sun MIBs rather than being polled directly.

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks
enterprises
mgmt

From SNMPv2-TC

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
mib_2	1.3.6.1.2.1
system	1.3.6.1.2.1.1
STR sysDescr	1.3.6.1.2.1.1.1	DisplayString	read-only	A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
OID sysObjectID	1.3.6.1.2.1.1.2	OBJECT IDENTIFIER	read-only	The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.
TIK sysUpTime	1.3.6.1.2.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the network management portion of the system was last re-initialized.
STR sysContact	1.3.6.1.2.1.1.4	DisplayString	read-write	The textual identification of the contact person for this managed node, together with information on how to contact this person.
STR sysName	1.3.6.1.2.1.1.5	DisplayString	read-only	An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
STR sysLocation	1.3.6.1.2.1.1.6	DisplayString	read-write	The physical location of this node (e.g., `telephone closet, 3rd floor').
INT sysServices	1.3.6.1.2.1.1.7	INTEGER	read-only	A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted.
interfaces	1.3.6.1.2.1.2
INT ifNumber	1.3.6.1.2.1.2.1	INTEGER	read-only	The number of network interfaces (regardless of their current state) present on this system.
ifTable	1.3.6.1.2.1.2.2		not-accessible	A list of interface entries. The number of entries is given by the value of ifNumber.
ifEntry	1.3.6.1.2.1.2.2.1		not-accessible	An interface entry containing objects at the subnetwork layer and below for a particular interface.
INT ifIndex	1.3.6.1.2.1.2.2.1.1	INTEGER	read-only	A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
STR ifDescr	1.3.6.1.2.1.2.2.1.2	DisplayString	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface.
INT ifType	1.3.6.1.2.1.2.2.1.3	INTEGER	read-only	The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack.
INT ifMtu	1.3.6.1.2.1.2.2.1.4	INTEGER	read-only	The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
GAU ifSpeed	1.3.6.1.2.1.2.2.1.5	Gauge	read-only	An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.
PHY ifPhysAddress	1.3.6.1.2.1.2.2.1.6	PhysAddress	read-only	The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.
INT ifAdminStatus	1.3.6.1.2.1.2.2.1.7	INTEGER	read-write	The desired state of the interface. The testing(3) state indicates that no operational packets can be passed.
INT ifOperStatus	1.3.6.1.2.1.2.2.1.8	INTEGER	read-only	The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed.
TIK ifLastChange	1.3.6.1.2.1.2.2.1.9	TimeTicks	read-only	The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
CTR ifInOctets	1.3.6.1.2.1.2.2.1.10	Counter	read-only	The total number of octets received on the interface, including framing characters.
CTR ifInUcastPkts	1.3.6.1.2.1.2.2.1.11	Counter	read-only	The number of subnetwork-unicast packets delivered to a higher-layer protocol.
CTR ifInNUcastPkts	1.3.6.1.2.1.2.2.1.12	Counter	read-only	The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
CTR ifInDiscards	1.3.6.1.2.1.2.2.1.13	Counter	read-only	The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
CTR ifInErrors	1.3.6.1.2.1.2.2.1.14	Counter	read-only	The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
CTR ifInUnknownProtos	1.3.6.1.2.1.2.2.1.15	Counter	read-only	The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
CTR ifOutOctets	1.3.6.1.2.1.2.2.1.16	Counter	read-only	The total number of octets transmitted out of the interface, including framing characters.
CTR ifOutUcastPkts	1.3.6.1.2.1.2.2.1.17	Counter	read-only	The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
CTR ifOutNUcastPkts	1.3.6.1.2.1.2.2.1.18	Counter	read-only	The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
CTR ifOutDiscards	1.3.6.1.2.1.2.2.1.19	Counter	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
CTR ifOutErrors	1.3.6.1.2.1.2.2.1.20	Counter	read-only	The number of outbound packets that could not be transmitted because of errors.
GAU ifOutQLen	1.3.6.1.2.1.2.2.1.21	Gauge	read-only	The length of the output packet queue (in packets).
OID ifSpecific	1.3.6.1.2.1.2.2.1.22	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
at	1.3.6.1.2.1.3
atTable	1.3.6.1.2.1.3.1		not-accessible	The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries.
atEntry	1.3.6.1.2.1.3.1.1		not-accessible	Each entry contains one NetworkAddress to `physical' address equivalence.
INT atIfIndex	1.3.6.1.2.1.3.1.1.1	INTEGER	read-only	The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
PHY atPhysAddress	1.3.6.1.2.1.3.1.1.2	PhysAddress	read-write	The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object.
IP atNetAddress	1.3.6.1.2.1.3.1.1.3	IpAddress	read-only	The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
ip	1.3.6.1.2.1.4
INT ipForwarding	1.3.6.1.2.1.4.1	INTEGER	read-write	The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.
INT ipDefaultTTL	1.3.6.1.2.1.4.2	INTEGER	read-only	The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.
CTR ipInReceives	1.3.6.1.2.1.4.3	Counter	read-only	The total number of input datagrams received from interfaces, including those received in error.
CTR ipInHdrErrors	1.3.6.1.2.1.4.4	Counter	read-only	The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.
CTR ipInAddrErrors	1.3.6.1.2.1.4.5	Counter	read-only	The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
CTR ipForwDatagrams	1.3.6.1.2.1.4.6	Counter	read-only	The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
CTR ipInUnknownProtos	1.3.6.1.2.1.4.7	Counter	read-only	The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
CTR ipInDiscards	1.3.6.1.2.1.4.8	Counter	read-only	The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
CTR ipInDelivers	1.3.6.1.2.1.4.9	Counter	read-only	The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
CTR ipOutRequests	1.3.6.1.2.1.4.10	Counter	read-only	The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.
CTR ipOutDiscards	1.3.6.1.2.1.4.11	Counter	read-only	The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
CTR ipOutNoRoutes	1.3.6.1.2.1.4.12	Counter	read-only	The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
INT ipReasmTimeout	1.3.6.1.2.1.4.13	INTEGER	read-only	The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity.
CTR ipReasmReqds	1.3.6.1.2.1.4.14	Counter	read-only	The number of IP fragments received which needed to be reassembled at this entity.
CTR ipReasmOKs	1.3.6.1.2.1.4.15	Counter	read-only	The number of IP datagrams successfully re- assembled.
CTR ipReasmFails	1.3.6.1.2.1.4.16	Counter	read-only	The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.
CTR ipFragOKs	1.3.6.1.2.1.4.17	Counter	read-only	The number of IP datagrams that have been successfully fragmented at this entity.
CTR ipFragFails	1.3.6.1.2.1.4.18	Counter	read-only	The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set.
CTR ipFragCreates	1.3.6.1.2.1.4.19	Counter	read-only	The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.
ipAddrTable	1.3.6.1.2.1.4.20		not-accessible	The table of addressing information relevant to this entity's IP addresses.
ipAddrEntry	1.3.6.1.2.1.4.20.1		not-accessible	The addressing information for one of this entity's IP addresses.
IP ipAdEntAddr	1.3.6.1.2.1.4.20.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
INT ipAdEntIfIndex	1.3.6.1.2.1.4.20.1.2	INTEGER	read-only	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP ipAdEntNetMask	1.3.6.1.2.1.4.20.1.3	IpAddress	read-only	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
INT ipAdEntBcastAddr	1.3.6.1.2.1.4.20.1.4	INTEGER	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
INT ipAdEntReasmMaxSize	1.3.6.1.2.1.4.20.1.5	INTEGER	read-only	The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
ipRouteTable	1.3.6.1.2.1.4.21		not-accessible	This entity's IP Routing table.
ipRouteEntry	1.3.6.1.2.1.4.21.1		not-accessible	A route to a particular destination.
IP ipRouteDest	1.3.6.1.2.1.4.21.1.1	IpAddress	read-write	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
INT ipRouteIfIndex	1.3.6.1.2.1.4.21.1.2	INTEGER	read-write	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT ipRouteMetric1	1.3.6.1.2.1.4.21.1.3	INTEGER	read-write	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric2	1.3.6.1.2.1.4.21.1.4	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric3	1.3.6.1.2.1.4.21.1.5	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric4	1.3.6.1.2.1.4.21.1.6	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
IP ipRouteNextHop	1.3.6.1.2.1.4.21.1.7	IpAddress	read-write	The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
INT ipRouteType	1.3.6.1.2.1.4.21.1.8	INTEGER	read-write	The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
INT ipRouteProto	1.3.6.1.2.1.4.21.1.9	INTEGER	read-only	The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
INT ipRouteAge	1.3.6.1.2.1.4.21.1.10	INTEGER	read-write	The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
IP ipRouteMask	1.3.6.1.2.1.4.21.1.11	IpAddress	read-write	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
INT ipRouteMetric5	1.3.6.1.2.1.4.21.1.12	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
OID ipRouteInfo	1.3.6.1.2.1.4.21.1.13	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
ipNetToMediaTable	1.3.6.1.2.1.4.22		not-accessible	The IP Address Translation table used for mapping from IP addresses to physical addresses.
ipNetToMediaEntry	1.3.6.1.2.1.4.22.1		not-accessible	Each entry contains one IpAddress to `physical' address equivalence.
INT ipNetToMediaIfIndex	1.3.6.1.2.1.4.22.1.1	INTEGER	read-only	The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
PHY ipNetToMediaPhysAddress	1.3.6.1.2.1.4.22.1.2	PhysAddress	read-write	The media-dependent `physical' address.
IP ipNetToMediaNetAddress	1.3.6.1.2.1.4.22.1.3	IpAddress	read-only	The IpAddress corresponding to the media- dependent `physical' address.
INT ipNetToMediaType	1.3.6.1.2.1.4.22.1.4	INTEGER	read-write	The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object.
CTR ipRoutingDiscards	1.3.6.1.2.1.4.23	Counter	read-only	The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries.
icmp	1.3.6.1.2.1.5
CTR icmpInMsgs	1.3.6.1.2.1.5.1	Counter	read-only	The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors.
CTR icmpInErrors	1.3.6.1.2.1.5.2	Counter	read-only	The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).
CTR icmpInDestUnreachs	1.3.6.1.2.1.5.3	Counter	read-only	The number of ICMP Destination Unreachable messages received.
CTR icmpInTimeExcds	1.3.6.1.2.1.5.4	Counter	read-only	The number of ICMP Time Exceeded messages received.
CTR icmpInParmProbs	1.3.6.1.2.1.5.5	Counter	read-only	The number of ICMP Parameter Problem messages received.
CTR icmpInSrcQuenchs	1.3.6.1.2.1.5.6	Counter	read-only	The number of ICMP Source Quench messages received.
CTR icmpInRedirects	1.3.6.1.2.1.5.7	Counter	read-only	The number of ICMP Redirect messages received.
CTR icmpInEchos	1.3.6.1.2.1.5.8	Counter	read-only	The number of ICMP Echo (request) messages received.
CTR icmpInEchoReps	1.3.6.1.2.1.5.9	Counter	read-only	The number of ICMP Echo Reply messages received.
CTR icmpInTimestamps	1.3.6.1.2.1.5.10	Counter	read-only	The number of ICMP Timestamp (request) messages received.
CTR icmpInTimestampReps	1.3.6.1.2.1.5.11	Counter	read-only	The number of ICMP Timestamp Reply messages received.
CTR icmpInAddrMasks	1.3.6.1.2.1.5.12	Counter	read-only	The number of ICMP Address Mask Request messages received.
CTR icmpInAddrMaskReps	1.3.6.1.2.1.5.13	Counter	read-only	The number of ICMP Address Mask Reply messages received.
CTR icmpOutMsgs	1.3.6.1.2.1.5.14	Counter	read-only	The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.
CTR icmpOutErrors	1.3.6.1.2.1.5.15	Counter	read-only	The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.
CTR icmpOutDestUnreachs	1.3.6.1.2.1.5.16	Counter	read-only	The number of ICMP Destination Unreachable messages sent.
CTR icmpOutTimeExcds	1.3.6.1.2.1.5.17	Counter	read-only	The number of ICMP Time Exceeded messages sent.
CTR icmpOutParmProbs	1.3.6.1.2.1.5.18	Counter	read-only	The number of ICMP Parameter Problem messages sent.
CTR icmpOutSrcQuenchs	1.3.6.1.2.1.5.19	Counter	read-only	The number of ICMP Source Quench messages sent.
CTR icmpOutRedirects	1.3.6.1.2.1.5.20	Counter	read-only	The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.
CTR icmpOutEchos	1.3.6.1.2.1.5.21	Counter	read-only	The number of ICMP Echo (request) messages sent.
CTR icmpOutEchoReps	1.3.6.1.2.1.5.22	Counter	read-only	The number of ICMP Echo Reply messages sent.
CTR icmpOutTimestamps	1.3.6.1.2.1.5.23	Counter	read-only	The number of ICMP Timestamp (request) messages sent.
CTR icmpOutTimestampReps	1.3.6.1.2.1.5.24	Counter	read-only	The number of ICMP Timestamp Reply messages sent.
CTR icmpOutAddrMasks	1.3.6.1.2.1.5.25	Counter	read-only	The number of ICMP Address Mask Request messages sent.
CTR icmpOutAddrMaskReps	1.3.6.1.2.1.5.26	Counter	read-only	The number of ICMP Address Mask Reply messages sent.
tcp	1.3.6.1.2.1.6
INT tcpRtoAlgorithm	1.3.6.1.2.1.6.1	INTEGER	read-only	The algorithm used to determine the timeout value used for retransmitting unacknowledged octets.
INT tcpRtoMin	1.3.6.1.2.1.6.2	INTEGER	read-only	The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793.
INT tcpRtoMax	1.3.6.1.2.1.6.3	INTEGER	read-only	The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793.
INT tcpMaxConn	1.3.6.1.2.1.6.4	INTEGER	read-only	The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1.
CTR tcpActiveOpens	1.3.6.1.2.1.6.5	Counter	read-only	The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.
CTR tcpPassiveOpens	1.3.6.1.2.1.6.6	Counter	read-only	The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.
CTR tcpAttemptFails	1.3.6.1.2.1.6.7	Counter	read-only	The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.
CTR tcpEstabResets	1.3.6.1.2.1.6.8	Counter	read-only	The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.
GAU tcpCurrEstab	1.3.6.1.2.1.6.9	Gauge	read-only	The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT.
CTR tcpInSegs	1.3.6.1.2.1.6.10	Counter	read-only	The total number of segments received, including those received in error. This count includes segments received on currently established connections.
CTR tcpOutSegs	1.3.6.1.2.1.6.11	Counter	read-only	The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets.
CTR tcpRetransSegs	1.3.6.1.2.1.6.12	Counter	read-only	The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets.
tcpConnTable	1.3.6.1.2.1.6.13		not-accessible	A table containing TCP connection-specific information.
tcpConnEntry	1.3.6.1.2.1.6.13.1		not-accessible	Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.
INT tcpConnState	1.3.6.1.2.1.6.13.1.1	INTEGER	read-write	The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably).
IP tcpConnLocalAddress	1.3.6.1.2.1.6.13.1.2	IpAddress	read-only	The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.
INT tcpConnLocalPort	1.3.6.1.2.1.6.13.1.3	INTEGER	read-only	The local port number for this TCP connection.
IP tcpConnRemAddress	1.3.6.1.2.1.6.13.1.4	IpAddress	read-only	The remote IP address for this TCP connection.
INT tcpConnRemPort	1.3.6.1.2.1.6.13.1.5	INTEGER	read-only	The remote port number for this TCP connection.
CTR tcpInErrs	1.3.6.1.2.1.6.14	Counter	read-only	The total number of segments received in error (e.g., bad TCP checksums).
CTR tcpOutRsts	1.3.6.1.2.1.6.15	Counter	read-only	The number of TCP segments sent containing the RST flag.
udp	1.3.6.1.2.1.7
CTR udpInDatagrams	1.3.6.1.2.1.7.1	Counter	read-only	The total number of UDP datagrams delivered to UDP users.
CTR udpNoPorts	1.3.6.1.2.1.7.2	Counter	read-only	The total number of received UDP datagrams for which there was no application at the destination port.
CTR udpInErrors	1.3.6.1.2.1.7.3	Counter	read-only	The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
CTR udpOutDatagrams	1.3.6.1.2.1.7.4	Counter	read-only	The total number of UDP datagrams sent from this entity.
udpTable	1.3.6.1.2.1.7.5		not-accessible	A table containing UDP listener information.
udpEntry	1.3.6.1.2.1.7.5.1		not-accessible	Information about a particular current UDP listener.
IP udpLocalAddress	1.3.6.1.2.1.7.5.1.1	IpAddress	read-only	The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used.
INT udpLocalPort	1.3.6.1.2.1.7.5.1.2	INTEGER	read-only	The local port number for this UDP listener.
transmission	1.3.6.1.2.1.10
snmp	1.3.6.1.2.1.11
CTR snmpInPkts	1.3.6.1.2.1.11.1	Counter	read-only	The total number of Messages delivered to the SNMP entity from the transport service.
CTR snmpOutPkts	1.3.6.1.2.1.11.2	Counter	read-only	The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service.
CTR snmpInBadVersions	1.3.6.1.2.1.11.3	Counter	read-only	The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version.
CTR snmpInBadCommunityNames	1.3.6.1.2.1.11.4	Counter	read-only	The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity.
CTR snmpInBadCommunityUses	1.3.6.1.2.1.11.5	Counter	read-only	The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message.
CTR snmpInASNParseErrs	1.3.6.1.2.1.11.6	Counter	read-only	The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages.
CTR snmpInTooBigs	1.3.6.1.2.1.11.8	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'.
CTR snmpInNoSuchNames	1.3.6.1.2.1.11.9	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'.
CTR snmpInBadValues	1.3.6.1.2.1.11.10	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'.
CTR snmpInReadOnlys	1.3.6.1.2.1.11.11	Counter	read-only	The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP.
CTR snmpInGenErrs	1.3.6.1.2.1.11.12	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'.
CTR snmpInTotalReqVars	1.3.6.1.2.1.11.13	Counter	read-only	The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs.
CTR snmpInTotalSetVars	1.3.6.1.2.1.11.14	Counter	read-only	The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs.
CTR snmpInGetRequests	1.3.6.1.2.1.11.15	Counter	read-only	The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInGetNexts	1.3.6.1.2.1.11.16	Counter	read-only	The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInSetRequests	1.3.6.1.2.1.11.17	Counter	read-only	The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInGetResponses	1.3.6.1.2.1.11.18	Counter	read-only	The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInTraps	1.3.6.1.2.1.11.19	Counter	read-only	The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpOutTooBigs	1.3.6.1.2.1.11.20	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.'
CTR snmpOutNoSuchNames	1.3.6.1.2.1.11.21	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'.
CTR snmpOutBadValues	1.3.6.1.2.1.11.22	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'.
CTR snmpOutGenErrs	1.3.6.1.2.1.11.24	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'.
CTR snmpOutGetRequests	1.3.6.1.2.1.11.25	Counter	read-only	The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutGetNexts	1.3.6.1.2.1.11.26	Counter	read-only	The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutSetRequests	1.3.6.1.2.1.11.27	Counter	read-only	The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutGetResponses	1.3.6.1.2.1.11.28	Counter	read-only	The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutTraps	1.3.6.1.2.1.11.29	Counter	read-only	The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity.
INT snmpEnableAuthenTraps	1.3.6.1.2.1.11.30	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system.
sun	1.3.6.1.4.1.42
products	1.3.6.1.4.1.42.2
sunMib	1.3.6.1.4.1.42.3
sunSystem	1.3.6.1.4.1.42.3.1
STR agentDescr	1.3.6.1.4.1.42.3.1.1	DisplayString	read-only	The SNMP agent's description of itself.
OCT hostID	1.3.6.1.4.1.42.3.1.2	OCTET STRING	read-only	The unique Sun hardware identifier. The value returned is four byte binary string.
STR motd	1.3.6.1.4.1.42.3.1.3	DisplayString	read-only	The first line of /etc/motd.
CTR unixTime	1.3.6.1.4.1.42.3.1.4	Counter	read-only	The Unix system time. Measured in seconds since January 1, 1970 GMT.
sunInterfaces	1.3.6.1.4.1.42.3.2
sunAt	1.3.6.1.4.1.42.3.3
sunIp	1.3.6.1.4.1.42.3.4
sunIcmp	1.3.6.1.4.1.42.3.5
sunTcp	1.3.6.1.4.1.42.3.6
sunUdp	1.3.6.1.4.1.42.3.7
sunSnmp	1.3.6.1.4.1.42.3.11
sunProcesses	1.3.6.1.4.1.42.3.12
sunProcessTable	1.3.6.1.4.1.42.3.12.1		read-only
psEntry	1.3.6.1.4.1.42.3.12.1.1		read-only
INT psProcessID	1.3.6.1.4.1.42.3.12.1.1.1	INTEGER	read-only	The process identifier for this process.
INT psParentProcessID	1.3.6.1.4.1.42.3.12.1.1.2	INTEGER	read-only	The process identifier of this process's parent.
INT psProcessSize	1.3.6.1.4.1.42.3.12.1.1.3	INTEGER	read-only	The combined size of the data and stack segments (in kilobytes.)
INT psProcessCpuTime	1.3.6.1.4.1.42.3.12.1.1.4	INTEGER	read-only	The CPU time (including both user and system time) consumed so far.
STR psProcessState	1.3.6.1.4.1.42.3.12.1.1.5	DisplayString	read-only	The run-state of the process. R - Runnable T - Stopped P - In page wait D - Non-interruptable wait S - Sleeping (less than 20 seconds) I - Idle (more than 20 seconds) Z - Zombie
STR psProcessWaitChannel	1.3.6.1.4.1.42.3.12.1.1.6	DisplayString	read-only	Reason process is waiting.
STR psProcessTTY	1.3.6.1.4.1.42.3.12.1.1.7	DisplayString	read-only	Terminal, if any, controlling this process.
STR psProcessUserName	1.3.6.1.4.1.42.3.12.1.1.8	DisplayString	read-only	Name of the user associated with this process.
INT psProcessUserID	1.3.6.1.4.1.42.3.12.1.1.9	INTEGER	read-only	Numeric form of the name of the user associated with this process.
STR psProcessName	1.3.6.1.4.1.42.3.12.1.1.10	DisplayString	read-only	Command name used to invoke this process.
INT psProcessStatus	1.3.6.1.4.1.42.3.12.1.1.11	INTEGER	read-write	Setting this variable will cause a signal of the set value to be sent to the process.
sunHostPerf	1.3.6.1.4.1.42.3.13
CTR rsUserProcessTime	1.3.6.1.4.1.42.3.13.1	Counter	read-only	total number of timeticks used by user processes since the system was last booted.
CTR rsNiceModeTime	1.3.6.1.4.1.42.3.13.2	Counter	read-only	total number of timeticks used by nice mode since the system was last booted.
CTR rsSystemProcessTime	1.3.6.1.4.1.42.3.13.3	Counter	read-only	total number of timeticks used by system processes since the system was last booted.
CTR rsIdleModeTime	1.3.6.1.4.1.42.3.13.4	Counter	read-only	total number of timeticks used in idle mode since the system was last booted.
CTR rsDiskXfer1	1.3.6.1.4.1.42.3.13.5	Counter	read-only
CTR rsDiskXfer2	1.3.6.1.4.1.42.3.13.6	Counter	read-only
CTR rsDiskXfer3	1.3.6.1.4.1.42.3.13.7	Counter	read-only
CTR rsDiskXfer4	1.3.6.1.4.1.42.3.13.8	Counter	read-only
CTR rsVPagesIn	1.3.6.1.4.1.42.3.13.9	Counter	read-only	Number of pages read in from disk.
CTR rsVPagesOut	1.3.6.1.4.1.42.3.13.10	Counter	read-only	Number of pages written to disk.
CTR rsVSwapIn	1.3.6.1.4.1.42.3.13.11	Counter	read-only	Number of pages swapped in.
CTR rsVSwapOut	1.3.6.1.4.1.42.3.13.12	Counter	read-only	Number of pages swapped out.
CTR rsVIntr	1.3.6.1.4.1.42.3.13.13	Counter	read-only	Number of device interrupts.
CTR rsIfInPackets	1.3.6.1.4.1.42.3.13.14	Counter	read-only	Number of input packets.
CTR rsIfOutPackets	1.3.6.1.4.1.42.3.13.15	Counter	read-only	Number of output packets.
CTR rsIfInErrors	1.3.6.1.4.1.42.3.13.16	Counter	read-only	Number of input errors.
CTR rsIfOutErrors	1.3.6.1.4.1.42.3.13.17	Counter	read-only	Number of output errors.
CTR rsIfCollisions	1.3.6.1.4.1.42.3.13.18	Counter	read-only	Number of output collisions.

RFC description

Sun Microsystems MIB module providing SNMP management capabilities for Sun server and platform devices, including extensions to the ENTITY-MIB for hardware inventory.

Start monitoring vendor-neutral base definitions module, Sun/Solaris SNMP agent host (shared textual conventions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SUN-SNMP

What Is SUN-SNMP?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description