SONUS-SS7-SERVICES-MIB

All MIBs › SONUS-SS7-SERVICES-MIB

Organization: Sonus Networks, Inc.

Last Updated: 2001-07-31

Category: Sonus Networks VoIP Softswitch, VoIP and Telephony

Description: Manages Sonus Networks softswitch SS7 signaling services including MTP linksets, routes, and point codes.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SONUS-SS7-SERVICES-MIB?

SONUS-SS7-SERVICES-MIB is a vendor MIB from Sonus Networks for configuring and monitoring SS7 (Signaling System 7) signaling gateway services on their softswitch platforms, covering SS7 gateway instances and node-level configuration used for PSTN interconnection. It exposes gateway configuration and state objects including operational state, socket/connection type, active and primary host associations, host IP addressing, and out-of-service delay timers governing failover behavior between redundant signaling hosts. This is primarily a software/service-status monitoring MIB: administrators use it to confirm SS7 gateway instances are in the correct operational state and that primary/backup host redundancy is functioning, which is critical for call-signaling availability rather than physical hardware sensors. It depends on the SONUS-SMI enterprise root and typically operates alongside SONUS-TCAP-CLIENT-SERVICES-MIB (for transaction-layer SS7 services) and SONUS-NODE-RESOURCES-MIB for overall node health. Typical deployment context is carrier telecom networks where Sonus signaling gateways bridge SS7-based PSTN switches with IP-based softswitch call control. Engineers can download the SONUS-SS7-SERVICES-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SONUS-SS7-SERVICES-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Sonus Networks (Ribbon Communications) SS7 signaling gateway/softswitch

Monitoring Examples

An admin would poll sonusSs7GatewayTable/sonusSs7GatewayEntry to check sonusSs7GatewayState and confirm which host is currently sonusSs7GatewayActiveHost, comparing it against the configured sonusSs7GatewayPriHostName/sonusSs7GatewayPriHostIpaddr. If the active host has failed over to a secondary unexpectedly, this would be visible as a mismatch between the active and primary host fields, prompting investigation into the primary's health. The sonusSs7GatewayPriHostOosDelayTimer setting would be checked to confirm failover timing is tuned appropriately to avoid signaling flaps during transient primary-host issues.

What Can Be Monitored

SS7 gateway operational state
active vs. primary signaling host
host IP addressing and socket type
out-of-service failover delay timing

Imported Objects

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION

From SONUS-COMMON-MIB

sonusEventClass	OBJECT-TYPE
sonusEventDescription	OBJECT-TYPE
sonusEventLevel	OBJECT-TYPE

From SONUS-SMI

sonusServicesMIBs

OBJECT-IDENTITY

From SONUS-TC

PointCode
SonusName
SonusPointCode
SonusPointCodeFormat

How to Use in IPNetwork Monitor

Example using sonusSs7NodeCurrentState OID:

Select a Sonus Networks (Ribbon Communications) signaling gateway/softswitch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type sonusSs7NodeCurrentState into the Find box to locate it in the OID tree, then select it and click OK. The current state of this SS7 node connection. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the value is 'failed' or 'congested', since 'offline'/'disabled' can be intentional and 'active'/'initializing' are both normal operating states. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
sonusSs7ServicesMIB	1.3.6.1.4.1.2879.2.5.3			The MIB Module for SS7 Gateway and SS7 Node Configuration.
sonusSs7ServicesMIBObjects	1.3.6.1.4.1.2879.2.5.3.1
sonusSs7Gateway	1.3.6.1.4.1.2879.2.5.3.1.1
I32 sonusSs7GatewayNextIndex	1.3.6.1.4.1.2879.2.5.3.1.1.1	Integer32	read-only	The next valid index to use when creating an entry in the sonusSs7GatewayTable.
sonusSs7GatewayTable	1.3.6.1.4.1.2879.2.5.3.1.1.2		not-accessible	This table specifies the SS7 Gateway list for the GSX9000 node.
sonusSs7GatewayEntry	1.3.6.1.4.1.2879.2.5.3.1.1.2.1		not-accessible
I32 sonusSs7GatewayIndex	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.1	Integer32	read-only	Identifies the target SS7 Gateway entry.
INT sonusSs7GatewayState	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.2	INTEGER	read-write	The administrative state of this SS7 Gateway entry.
SON sonusSs7GatewayName	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.3	SonusName	read-write	The name of this SS7 Gateway instance.
INT sonusSs7GatewaySocketType	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.4	INTEGER	read-write	Indicates the type of socket interface used by the GSX9000 node for connections to the SS7 Gateway platform.
INT sonusSs7GatewayActiveHost	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.5	INTEGER	read-only	This status value has been replaced by sonusSs7GatewayNextHost and sonusSs7GatewaySelectHost.
STR sonusSs7GatewayPriHostName	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.6	DisplayString	read-write	The host name of the primary link to the SS7 Gateway platform.
IP sonusSs7GatewayPriHostIpaddr	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.7	IpAddress	read-write	Specifies the IP Address of the primary link to the SS7 Gateway platform.
INT sonusSs7GatewayPriHostMode	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.8	INTEGER	read-write	Specifies the service mode of the primary link to the SS7 Gateway platform.
I32 sonusSs7GatewayPriHostOosDelayTimer	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.9	Integer32	read-write	This element is used to delay the action of taking the primary host link out of service for a specified number of minutes.
STR sonusSs7GatewaySecHostName	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.10	DisplayString	read-write	The host name of the secondary link to the SS7 Gateway platform.
IP sonusSs7GatewaySecHostIpaddr	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.11	IpAddress	read-write	Specifies the IP Address of the secondary link to the SS7 Gateway platform.
INT sonusSs7GatewaySecHostMode	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.12	INTEGER	read-write	Specifies the service mode of the secondary link to the SS7 Gateway platform.
I32 sonusSs7GatewaySecHostOosDelayTimer	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.13	Integer32	read-write	This element is used to delay the action of taking the secondary host link out of service for a specified number of minutes.
ROW sonusSs7GatewayRowStatus	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.14	RowStatus	read-write
IP sonusSs7GatewayPriAltHostIpaddr	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.15	IpAddress	read-write	Specifies the alternate IP Address of the primary link to the SS7 Gateway platform.
IP sonusSs7GatewaySecAltHostIpaddr	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.16	IpAddress	read-write	Specifies the alternate IP Address of the secondary link to the SS7 Gateway platform.
INT sonusSs7GatewayGwType	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.17	INTEGER	read-write	Gateway type is identified by the gateway protocol it uses
I32 sonusSs7GatewayServerTcpPort	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.18	Integer32	read-write	TCP port for the server of TALI connection
I32 sonusSs7GatewayClientTcpPort	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.19	Integer32	read-write	TCP port for the client of TALI connection
INT sonusSs7GatewayPriTaliTrafficControl	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.20	INTEGER	read-write	Control the ss7 traffic on the primary TALI connection
INT sonusSs7GatewayPriAltTaliTrafficControl	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.21	INTEGER	read-write	Control the ss7 traffic on the primary TALI connection
INT sonusSs7GatewaySecTaliTrafficControl	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.22	INTEGER	read-write	Control the ss7 traffic on the secondary TALI connection
INT sonusSs7GatewaySecAltTaliTrafficControl	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.23	INTEGER	read-write	Control the ss7 traffic on the secondary TALI connection
I32 sonusSs7GatewayTimerTaliT1	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.24	Integer32	read-write	Send a TALI-TEST upon the expiry of T1 in millisecond.
I32 sonusSs7GatewayTimerTaliT2	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.25	Integer32	read-write	Guard timer in millisecond for the return of TALI-ALLO or TALI-PROH in response to a TALI-TEST sent earlier.
I32 sonusSs7GatewayTimerTaliT3	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.26	Integer32	read-write	T3 in millisecond reprsents how long the near end can continue to process received messages after sending TALI-PROH.
I32 sonusSs7GatewayTimerTaliT4	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.27	Integer32	read-write	Send a TALI-MONI upon the expiry of T4 in millisecond.
INT sonusSs7GatewayTaliSs7Type	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.28	INTEGER	read-write	SS7 protocol types used over TALI
I32 sonusSs7GatewaySlsBits	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.29	Integer32	read-write	The number of SLS bits to use
INT sonusSs7GatewayTaliIsupNormalization	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.30	INTEGER	read-write	ISUP message format over TALI -- normalized or raw
INT sonusSs7GatewayTaliPstnPresentation	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.31	INTEGER	read-write	ISUP types over TALI
STR sonusSs7GatewayTaliGroupCode	1.3.6.1.4.1.2879.2.5.3.1.1.2.1.32	DisplayString	read-write	Group Code in ASCII
sonusSs7GatewayStatusTable	1.3.6.1.4.1.2879.2.5.3.1.1.3		not-accessible	Status Table of the SS7 Gateway for the GSX9000 node.
sonusSs7GatewayStatusEntry	1.3.6.1.4.1.2879.2.5.3.1.1.3.1		not-accessible	List of SS7 Gateway status elements.
I32 sonusSs7GatewayStatusIndex	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.1	Integer32	read-only	Identifies the SS7 Gateway status entry.
SON sonusSs7GatewayNextHost	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.2	SonusSs7GatewayLinkSelection	read-only	Indicates which host link connection to the SS7 Gateway is next to be selected. If there is none, then this element is set to none.
SON sonusSs7GatewaySelectHost	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.3	SonusSs7GatewayLinkSelection	read-only	Indicates which host link connection to the SS7 Gateway is selected to be tried. If there is none, then this element is set to none.
INT sonusSs7GatewayPriTaliConnState	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.4	INTEGER	read-only	TALI state of the primary connection for this SS7 gateway.
INT sonusSs7GatewaySecTaliConnState	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.5	INTEGER	read-only	TALI state of the secondary connection for this SS7 gateway.
INT sonusSs7GatewayPriAltTaliConnState	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.6	INTEGER	read-only	TALI state of the primary alt connection for this SS7 gateway.
INT sonusSs7GatewaySecAltTaliConnState	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.7	INTEGER	read-only	TALI state of the secondary alt connection for this SS7 gateway.
STR sonusSs7GatewayPriNearEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.8	DisplayString	read-only	TALI protocol version at the near end of the pri conncection
STR sonusSs7GatewayPriFarEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.9	DisplayString	read-only	TALI protocol version at the far end of the pri connection
STR sonusSs7GatewayPriAltNearEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.10	DisplayString	read-only	TALI protocol version at the near end of the pri-alt conn.
STR sonusSs7GatewayPriAltFarEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.11	DisplayString	read-only	TALI protocol version at the far end of the pri-alt connection
STR sonusSs7GatewaySecNearEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.12	DisplayString	read-only	TALI protocol version at the near end of the sec conncection
STR sonusSs7GatewaySecFarEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.13	DisplayString	read-only	TALI protocol version at the far end of the sec connection
STR sonusSs7GatewaySecAltNearEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.14	DisplayString	read-only	TALI protocol version at the near end of the sec-alt conn.
STR sonusSs7GatewaySecAltFarEndTaliVersion	1.3.6.1.4.1.2879.2.5.3.1.1.3.1.15	DisplayString	read-only	TALI protocol version at the far end of the sec-alt connection
sonusSs7GatewayPSStatusTable	1.3.6.1.4.1.2879.2.5.3.1.1.4		not-accessible	Status Table of the SS7 Gateway of a PRIMARY or SECONDARY for the GSX9000 node.
sonusSs7GatewayPSStatusEntry	1.3.6.1.4.1.2879.2.5.3.1.1.4.1		not-accessible	List of SS7 Gateway status elements.
I32 sonusSs7GatewayPSStatusIndex	1.3.6.1.4.1.2879.2.5.3.1.1.4.1.1	Integer32	read-only	Identifies the SS7 Gateway status entry.
INT sonusSs7GatewayPSStatusPSIndex	1.3.6.1.4.1.2879.2.5.3.1.1.4.1.2	INTEGER	read-only	Identifies the SS7 Gateway link status entry.
I32 sonusSs7GatewayPSStatusPrimaryCE	1.3.6.1.4.1.2879.2.5.3.1.1.4.1.3	Integer32	read-only	Identifies the link Primary CE value.
I32 sonusSs7GatewayPSStatusActiveLink	1.3.6.1.4.1.2879.2.5.3.1.1.4.1.4	Integer32	read-only	Identifies the link active entry.
sonusSs7GatewayLinkStatusTable	1.3.6.1.4.1.2879.2.5.3.1.1.5		not-accessible	Link Status Table of a SS7 Gateway for the GSX9000 node.
sonusSs7GatewayLinkStatusEntry	1.3.6.1.4.1.2879.2.5.3.1.1.5.1		not-accessible	List of SS7 Gateway Link Status elements.
I32 sonusSs7GatewayStatusLinkIndex	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.1	Integer32	read-only	Identifies the SS7 Gateway status link entry gateway index.
INT sonusSs7GatewayStatusLinkPSIndex	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.2	INTEGER	read-only	Identifies the SS7 Gateway status link entry primary or secondary index.
I32 sonusSs7GatewayStatusLinkHostIndex	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.3	Integer32	read-only	Identifies the SS7 Gateway host status link entry index.
STR sonusSs7GatewayStatusHostName	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.4	DisplayString	read-only	The host name of the Link link to the SS7 Gateway platform.
IP sonusSs7GatewayStatusHostIpaddr	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.5	IpAddress	read-only	Specifies the IP Address of the link to the SS7 Gateway platform.
INT sonusSs7GatewayStatusHostState	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.6	INTEGER	read-only	The state of host link to the SS7 Gateway platform.
I32 sonusSs7GatewayStatusHostCE	1.3.6.1.4.1.2879.2.5.3.1.1.5.1.7	Integer32	read-only	The CE of host link to the SS7 Gateway platform.
sonusSs7NodeStatusTable	1.3.6.1.4.1.2879.2.5.3.1.1.6		not-accessible	Status Table of the SS7 Node for the GSX9000 node.
sonusSs7NodeStatusEntry	1.3.6.1.4.1.2879.2.5.3.1.1.6.1		not-accessible	List of SS7 Node status elements.
I32 sonusSs7NodeStatusIndex	1.3.6.1.4.1.2879.2.5.3.1.1.6.1.1	Integer32	read-only	Identifies the SS7 Node status entry.
INT sonusSs7NodeStatIsup	1.3.6.1.4.1.2879.2.5.3.1.1.6.1.2	INTEGER	read-only	Specifies the operating status of the ISUP service within this SS7 Node.
INT sonusSs7NodeStatMtp	1.3.6.1.4.1.2879.2.5.3.1.1.6.1.3	INTEGER	read-only	Specifies the current MTP status for this SS7 Node.
sonusSs7Node	1.3.6.1.4.1.2879.2.5.3.1.2
I32 sonusSs7NodeNextIndex	1.3.6.1.4.1.2879.2.5.3.1.2.1	Integer32	read-only	The next valid index to use when creating an entry in the sonusSs7NodeTable.
sonusSs7NodeTable	1.3.6.1.4.1.2879.2.5.3.1.2.2		not-accessible	This table specifies the SS7 Node list for the GSX9000 node.
sonusSs7NodeEntry	1.3.6.1.4.1.2879.2.5.3.1.2.2.1		not-accessible
I32 sonusSs7NodeIndex	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.1	Integer32	read-only	Identifies the target SS7 Node entry.
INT sonusSs7NodeState	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.2	INTEGER	read-write	The administrative state of this SS7 Node entry.
SON sonusSs7NodeName	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.3	SonusName	read-write	The name of this SS7 Node instance.
NUM sonusSs7NodePointCode	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.4	PointCode	read-write	The SS7 point code assigned to this SS7 Node entry.
INT sonusSs7NodeServices	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.5	INTEGER	read-write	The type of SS7 services (ISUP, TCAP, or both) supported by this SS7 Node entry. As of GSX release 3.02.00, isupOnly is now the only vaild option for this entry.
INT sonusSs7NodeProtocol	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.6	INTEGER	read-write	The SS7 protocol type supported by this SS7 Node entry.
I32 sonusSs7NodeTcapSsn	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.7	Integer32	read-write	If Tcap is supported by this SS7 Node, specifies the Sub System Number for this node entry. This object is obsoleted as of GSX release 3.02.00.
INT sonusSs7NodeIsupStatus	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.8	INTEGER	read-only	This status value has been replaced by sonusSs7NodeStatIsup
INT sonusSs7NodeTcapStatus	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.9	INTEGER	read-only	Specifies the operating status of the TCAP service within this SS7 Node. This object is obsoleted as of GSX release 3.02.00.
INT sonusSs7NodeMtpStatus	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.10	INTEGER	read-only	This status value has been replaced by sonusSs7NodeStatMtp
STR sonusSs7NodeGatewayAssignment	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.11	DisplayString	read-write	The name of the SS7 Gateway to which this SS7 Node is assigned.
I32 sonusSs7NodeNativePointCode	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.12	Integer32	read-only	The native point code of the SS7 node. e.g. For ITU the point code is in 3 bit 8 bit 3 bit format adding up to 14 bits whereas ANSI uses a 8bit 8bit 8bit format adding up to 24 bits.
INT sonusSs7NodeMode	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.13	INTEGER	read-write	Specifies the service mode for this SS7 Node.
INT sonusSs7NodeConnCntrl	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.14	INTEGER	read-write	Specifies when the Node will establish an ISUP connection with the SS7 Gateway. This parameter is used to minimize unnecessary connections to the SS7 Gateway for ISUP services, allowing the GSX to only establish the ISUP connections that are required by ISUP circuits on a particular shelf. When set to always, the ISUP service connection will be established when the node is enabled. When set to asNeeded, the ISUP service connection will be established only if there are ISUP circuits assigned to this node. This parameter only applies to ISUP service registration.
ROW sonusSs7NodeRowStatus	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.15	RowStatus	read-write
NUM sonusSs7NodeStdPointCode	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.16	SonusPointCode	read-write	Octet string of the point code. This gives the actual representation the user entered.
I32 sonusSs7NodePointCodeSize	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.17	Integer32	read-write	Indicates the total number of bits in the point code.
NUM sonusSs7NodePointCodeFormatType	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.18	SonusPointCodeFormat	read-write	The Point Code format type being defined.
INT sonusSs7NodeServerProtocol	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.19	INTEGER	read-write	The interface used between the SS7 gateway and the SS7 client on the GSX9000
I32 sonusSs7NodeHandShakeInterval	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.20	Integer32	read-write	HandShake interval between the client and the server in seconds.
I32 sonusSs7NodeTimerT1	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.21	Integer32	read-write	The Timer T1 could be changed from its default using this entry. The valid ranges are 4 - 15 seconds for ANSI and 15 - 60 Seconds for ITU.
I32 sonusSs7NodeTimerT2	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.22	Integer32	read-write	The Timer T2 could be changed from its default using this entry. The valid value for ITU is 3 Minutes. This timer has no relevence in the ANSI network.
I32 sonusSs7NodeTimerT3	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.23	Integer32	read-write	The T3 timer is started on receipt of an Overload message in the ITU network. This has no relevence in the ANSI network. The valid ITU recommended value is 120 Seconds
I32 sonusSs7NodeTimerT4	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.24	Integer32	read-write	The Timer T4 could be changed from its default using this entry.
I32 sonusSs7NodeTimerT5	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.25	Integer32	read-write	The T5 Timer is started when the release message is sent. The valid values as per the specifications are 60 seconds for the ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7NodeTimerT6	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.26	Integer32	read-write	The timer T6 is started when the suspend message is received. The valid range for this timer is 1 to 120 seconds.
I32 sonusSs7NodeTimerT7	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.27	Integer32	read-write	The Timer T7 could be changed from its default using this entry.
I32 sonusSs7NodeTimerT8	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.28	Integer32	read-write	The T8 timer is timer to be started with continuity check has been indicated in the IAM. The valid range is 10 to 15 seconds.
I32 sonusSs7NodeTimerT9	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.29	Integer32	read-write	The Timer T9 started when outgoing international exchange recieves an ACM. The valid range is 120 to 240 seconds.
I32 sonusSs7NodeTimerT10	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.30	Integer32	read-write	The Timer T10 is started when the last digit is recived in interworking situations. This timer has no relevence to ANSI.
I32 sonusSs7NodeTimerT11	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.31	Integer32	read-write	The Timer T11 is started when the latest address message is received in interworking situations. The valid range is 15 to 20 seconds.
I32 sonusSs7NodeTimerT12	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.32	Integer32	read-write	The Timer T12 is started when a blocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7NodeTimerT13	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.33	Integer32	read-write	The Timer T13 is started when the initial blocking messge is sent. The valid value for ANSI is 60 seconds and for ITU is between 300 and 900 seconds.
I32 sonusSs7NodeTimerT14	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.34	Integer32	read-write	The Timer T14 is started when an unblocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU
I32 sonusSs7NodeTimerT15	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.35	Integer32	read-write	The Timer T15 is started when the initial unblocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7NodeTimerT16	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.36	Integer32	read-write	The Timer T16 is started when the reset circuit is started which was not due to expiry of T5. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7NodeTimerT17	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.37	Integer32	read-write	The Timer T17 is started when initial reset message is sent. The valid values are 60 seconds for ANSI and 300 to 900 for ITU.
I32 sonusSs7NodeTimerT18	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.38	Integer32	read-write	The Timer T18 is started when circuit group blocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7NodeTimerT19	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.39	Integer32	read-write	The Timer T19 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7NodeTimerT20	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.40	Integer32	read-write	The Timer T20 is started when group unblocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7NodeTimerT21	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.41	Integer32	read-write	The Timer T21 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7NodeTimerT22	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.42	Integer32	read-write	The Timer T22 is started when circuit group reset message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7NodeTimerT23	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.43	Integer32	read-write	The Timer T23 is started when initial group reset message is sent. The valid values are 60 seconds for the ANSI and 300 to 900 seconds for the ITU.
I32 sonusSs7NodeTimerT24	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.44	Integer32	read-write	The Timer T24 is started when check tone is sent. The value is less than 2 seconds.
I32 sonusSs7NodeTimerT25	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.45	Integer32	read-write	The Timer T25 is started when initial continuity check failure is detected. The range is 1 to 10 seconds.
I32 sonusSs7NodeTimerT26	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.46	Integer32	read-write	The Timer T26 is started when a second or subsequent continuity failure is detected. The valid value are 60 to 180 seconds.
I32 sonusSs7NodeTimerT27	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.47	Integer32	read-write	The Timer T27 is started when a continuity fail message is recieved. The valid values are more than 180 seconds for ANSI and 240 seconds for ITU.
I32 sonusSs7NodeTimerT28	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.48	Integer32	read-write	The Timer T28 is started when Circuit Query Message is sent. The valid value is 10 seconds.
I32 sonusSs7NodeTimerT29	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.49	Integer32	read-write	The Timer T29 is started when Congestion indication is received when T29 is not running. The valid range is 300 to 600 milli second. This timer has no relevence for ANSI.
I32 sonusSs7NodeTimerT30	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.50	Integer32	read-write	The Timer T30 is stared when congestion indication is recieved when T29 is not running. The valid range is 5 to 10 seconds for the ITU. This timer has no relevence under ANSI.
I32 sonusSs7NodeTimerT31	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.51	Integer32	read-write	The Timer T31 is started on release of ISUP signalling connection based on CO SCCP. The value should be set to greater than 360 seconds
I32 sonusSs7NodeTimerT32	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.52	Integer32	read-write	The Timer T32 is started when the first end-to-end message is recived. Under ANSI this timer is started after the response to such a message is sent. The valid values are 3 to 5 seconds.
I32 sonusSs7NodeTimerT33	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.53	Integer32	read-write	The Timer T33 is started when Information Request Message is sent. The valid range is 12 to 15 seconds.
I32 sonusSs7NodeTimerT34	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.54	Integer32	read-write	The Timer T34 is started when Loop Back Acknowledgement is sent under ANSI. The Timer T34 is started when segmentation is received for IAM, ACM, CPG, ANM or CON under ITU. The valid range for ANSI is 10 to 15 seconds. The valid range for ITU is 2 to 4 seconds.
I32 sonusSs7NodeTimerT35	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.55	Integer32	read-write	The Timer T35 is started when the last digit recieved is not an ST digit or the fixed number of digits have been recieved. This procedure is only valid for overlap hence ITU. This timer has no relevence in ANSI.
I32 sonusSs7NodeTimerT36	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.56	Integer32	read-write	The Timer T36 is started when IAM is recived with a segmentation indication for ANSI. This timer is started when transit or incoming international exchange recieves Continuity check request message. The valid range for ANSI is 2 to 4 seconds and 10 to 15 seconds for ITU.
I32 sonusSs7NodeTimerT37	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.57	Integer32	read-write	The Timer T37 is started when User Part Availability test is started under ANSI. This timer is started when a request for and Echo control device is sent to another exchange under ITU. The valid value for ANSI is 30 seconds and for ITU is 2 to 4 seconds.
I32 sonusSs7NodeTimerT38	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.58	Integer32	read-write	The Timer T38 is started when a suspend message is sent to the preceding switch. This timer is only relevent under ITU.
I32 sonusSs7NodeTimerT39	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.59	Integer32	read-write	The Timer T39 is started when MCID request is sent. It is only relevent in the ITU.
I32 sonusSs7NodeTimerT40	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.60	Integer32	read-write	The Timer T40 could be changed from its default using this entry.
I32 sonusSs7NodeTimerTAcc	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.61	Integer32	read-write	Automatic Congestion Control Timer as per ANSI T1.113.4 - 1995. The value of the timer is 5 Seconds.
I32 sonusSs7NodeTimerTCcr	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.62	Integer32	read-write	Continuity Check Request Timer. The value As per ANSI T1.113.4 - 1995 is 2 Seconds.
I32 sonusSs7NodeTimerTCcrr	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.63	Integer32	read-write	Continuity Check Failed Recived. The value as per ANSI T1.113.4 - 1995 is 20 Seconds.
I32 sonusSs7NodeTimerTCgb	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.64	Integer32	read-write	Timer started on recipt of a Circuit Group Block Message. The value as per ANSI T1.113.4 - 1995 is 5 Seconds.
I32 sonusSs7NodeTimerTCra	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.65	Integer32	read-write	Timer started when Circuit Reservation Acknowledgment is sent. The time value as per ANSI T1.113.4 - 1995 is 20 seconds.
I32 sonusSs7NodeTimerTCrm	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.66	Integer32	read-write	This timer is started when the circuit reservation message is sent. The value as per ANSI T1.113.4 - 1995 is 3 - 4 Seconds. The default is set to 4 seconds.
I32 sonusSs7NodeTimerTCvt	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.67	Integer32	read-write	The Timer T CVT is started when the Circuit Validation Test message is sent. This message is only valid for ANSI.
I32 sonusSs7NodeTimerTExm	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.68	Integer32	read-write	The Timer Exm,d is started when IAM is sent to the succeeding network. This timer has no relevence in the ITU. This timer is in milliseconds
I32 sonusSs7NodeTimerTGrs	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.69	Integer32	read-write	This timer is started when a circuit group reset message is received. This timer is only relevent in the ANSI network.
I32 sonusSs7NodeTimerTHga	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.70	Integer32	read-write	This timer is started on recognition of carrier loss. It is only relevent in ANSI network. The valid range is 0 to 300 seconds.
I32 sonusSs7NodeTimerTScga	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.71	Integer32	read-write	This timer is started when initial demand continuity check fails in the SCGA group. The valid range for this timer is 0 to 120 seconds.
I32 sonusSs7NodeTimerTScgad	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.72	Integer32	read-write	This timer is started failure of demand continuity check in the SCGA group.
STR sonusSs7NodeApplProfileName	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.73	DisplayString	read-write	The SS7 Node Profile to be applied to the node. The values here are a snap shot only and might have changed since they were set.
INT sonusSs7NodeNetworkInd	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.74	INTEGER	read-write	The setting of the Network Indicator used for this SS7 Node entry.
I32 sonusSs7NodeSlsBits	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.75	Integer32	read-write	The number of SLS bits to use
I32 sonusSs7NodeTimerTA	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.76	Integer32	read-write	The Bellcore specific timer TA is the guard timer on outgoing SS7 circuit before idling. The value of this timer is 0 to 1000 milliseconds.
I32 sonusSs7NodeTimerTBlom	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.77	Integer32	read-write	The Bellcore specific timer TBlom is started when blocking a circuit due to a BLO, and after any call is released; used to notify maintenance.
I32 sonusSs7NodeTimerTCotd	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.78	Integer32	read-write	The Bellcore specific timer TCOTd is started when sending IAM requesting continuity check. The value of this timer is in milliseconds.
I32 sonusSs7NodeTimerTCotl	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.79	Integer32	read-write	The Bellcore specific timer TCOTl is started when receiving second COT coded failed, awaiting receipt of CCR.
I32 sonusSs7NodeTimerTSus	1.3.6.1.4.1.2879.2.5.3.1.2.2.1.80	Integer32	read-write	The Bellcore specific timer TSUS is started when a SUS message is sent by the terminating switch, awaiting called party off-hook or REL.
sonusSs7NodeProfile	1.3.6.1.4.1.2879.2.5.3.1.3
I32 sonusSs7NodeProfileNextIndex	1.3.6.1.4.1.2879.2.5.3.1.3.1	Integer32	read-only	The next valid index to use when creating an entry in the sonusSs7NodeProfileTable.
sonusSs7NodeProfileTable	1.3.6.1.4.1.2879.2.5.3.1.3.2		not-accessible	This table specifies the SS7 Node Profile list for the GSX9000 node.
sonusSs7NodeProfileEntry	1.3.6.1.4.1.2879.2.5.3.1.3.2.1		not-accessible
I32 sonusSs7NodeProfileIndex	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.1	Integer32	read-only	Identifies the SS7 Node Profile entry
SON sonusSs7NodeProfileName	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.2	SonusName	read-write	The name of the Node Profile
I32 sonusSs7PointCodeSize	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.3	Integer32	read-write	Indicates the total number of bits in the point code.
NUM sonusSs7PointCodeFormatType	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.4	SonusPointCodeFormat	read-write	The Point Code format type being defined.
INT sonusSs7ServerProtocol	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.5	INTEGER	read-write	The interface used between the SS7 gateway and the SS7 client on the GSX9000
I32 sonusSs7HandShakeInterval	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.6	Integer32	read-write	HandShake interval between the client and the server in seconds.
I32 sonusSs7TimerT1	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.7	Integer32	read-write	The Timer T1 could be changed from its default using this entry. The valid ranges are 4 - 15 seconds for ANSI and 15 - 60 Seconds for ITU.
I32 sonusSs7TimerT2	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.8	Integer32	read-write	The Timer T2 could be changed from its default using this entry. The valid value for ITU is 3 Minutes. This timer has no relevence in the ANSI network.
I32 sonusSs7TimerT3	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.9	Integer32	read-write	The T3 timer is started on receipt of an Overload message in the ITU network. This has no relevence in the ANSI network. The valid ITU recommended value is 120 Seconds
I32 sonusSs7TimerT4	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.10	Integer32	read-write	The Timer T4 could be changed from its default using this entry.
I32 sonusSs7TimerT5	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.11	Integer32	read-write	The T5 Timer is started when the release message is sent. The valid values as per the specifications are 60 seconds for the ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7TimerT6	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.12	Integer32	read-write	The timer T6 is started when the suspend message is received. The valid range for this timer is 10 to 32 seconds.
I32 sonusSs7TimerT7	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.13	Integer32	read-write	The Timer T7 could be changed from its default using this entry.
I32 sonusSs7TimerT8	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.14	Integer32	read-write	The T8 timer is timer to be started with continuity check has been indicated in the IAM. The valid range is 10 to 15 seconds.
I32 sonusSs7TimerT9	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.15	Integer32	read-write	The Timer T9 started when outgoing international exchange recieves an ACM. The valid range is 120 to 240 seconds.
I32 sonusSs7TimerT10	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.16	Integer32	read-write	The Timer T10 is started when the last digit is recived in interworking situations. This timer has no relevence to ANSI.
I32 sonusSs7TimerT11	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.17	Integer32	read-write	The Timer T11 is started when the latest address message is received in interworking situations. The valid range is 15 to 20 seconds.
I32 sonusSs7TimerT12	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.18	Integer32	read-write	The Timer T12 is started when a blocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7TimerT13	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.19	Integer32	read-write	The Timer T13 is started when the initial blocking messge is sent. The valid value for ANSI is 60 seconds and for ITU is between 300 and 900 seconds.
I32 sonusSs7TimerT14	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.20	Integer32	read-write	The Timer T14 is started when an unblocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU
I32 sonusSs7TimerT15	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.21	Integer32	read-write	The Timer T15 is started when the initial unblocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7TimerT16	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.22	Integer32	read-write	The Timer T16 is started when the reset circuit is started which was not due to expiry of T5. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7TimerT17	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.23	Integer32	read-write	The Timer T17 is started when initial reset message is sent. The valid values are 60 seconds for ANSI and 300 to 900 for ITU.
I32 sonusSs7TimerT18	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.24	Integer32	read-write	The Timer T18 is started when circuit group blocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7TimerT19	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.25	Integer32	read-write	The Timer T19 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7TimerT20	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.26	Integer32	read-write	The Timer T20 is started when group unblocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7TimerT21	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.27	Integer32	read-write	The Timer T21 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
I32 sonusSs7TimerT22	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.28	Integer32	read-write	The Timer T22 is started when circuit group reset message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
I32 sonusSs7TimerT23	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.29	Integer32	read-write	The Timer T23 is started when initial group reset message is sent. The valid values are 60 seconds for the ANSI and 300 to 900 seconds for the ITU.
I32 sonusSs7TimerT24	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.30	Integer32	read-write	The Timer T24 is started when check tone is sent. The value is less than 2 seconds.
I32 sonusSs7TimerT25	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.31	Integer32	read-write	The Timer T25 is started when initial continuity check failure is detected. The range is 1 to 10 seconds.
I32 sonusSs7TimerT26	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.32	Integer32	read-write	The Timer T26 is started when a second or subsequent continuity failure is detected. The valid value are 60 to 180 seconds.
I32 sonusSs7TimerT27	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.33	Integer32	read-write	The Timer T27 is started when a continuity fail message is recieved. The valid values are more than 180 seconds for ANSI and 240 seconds for ITU.
I32 sonusSs7TimerT28	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.34	Integer32	read-write	The Timer T28 is started when Circuit Query Message is sent. The valid value is 10 seconds.
I32 sonusSs7TimerT29	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.35	Integer32	read-write	The Timer T29 is started when Congestion indication is received when T29 is not running. The valid range is 300 to 600 milli second. This timer has no relevence for ANSI.
I32 sonusSs7TimerT30	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.36	Integer32	read-write	The Timer T30 is stared when congestion indication is recieved when T29 is not running. The valid range is 5 to 10 seconds for the ITU. This timer has no relevence under ANSI.
I32 sonusSs7TimerT31	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.37	Integer32	read-write	The Timer T31 is started on release of ISUP signalling connection based on CO SCCP. The value should be set to greater than 360 seconds
I32 sonusSs7TimerT32	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.38	Integer32	read-write	The Timer T32 is started when the first end-to-end message is recived. Under ANSI this timer is started after the response to such a message is sent. The valid values are 3 to 5 seconds.
I32 sonusSs7TimerT33	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.39	Integer32	read-write	The Timer T33 is started when Information Request Message is sent. The valid range is 12 to 15 seconds.
I32 sonusSs7TimerT34	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.40	Integer32	read-write	The Timer T34 is started when Loop Back Acknowledgement is sent under ANSI. The Timer T34 is started when segmentation is received for IAM, ACM, CPG, ANM or CON under ITU. The valid range for ANSI is 10 to 15 seconds. The valid range for ITU is 2 to 4 seconds.
I32 sonusSs7TimerT35	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.41	Integer32	read-write	The Timer T35 is started when the last digit recieved is not an ST digit or the fixed number of digits have been recieved. This procedure is only valid for overlap hence ITU. This timer has no relevence in ANSI.
I32 sonusSs7TimerT36	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.42	Integer32	read-write	The Timer T36 is started when IAM is recived with a segmentation indication for ANSI. This timer is started when transit or incoming international exchange recieves Continuity check request message. The valid range for ANSI is 2 to 4 seconds and 10 to 15 seconds for ITU.
I32 sonusSs7TimerT37	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.43	Integer32	read-write	The Timer T37 is started when User Part Availability test is started under ANSI. This timer is started when a request for and Echo control device is sent to another exchange under ITU. The valid value for ANSI is 30 seconds and for ITU is 2 to 4 seconds.
I32 sonusSs7TimerT38	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.44	Integer32	read-write	The Timer T38 is started when a suspend message is sent to the preceding switch. This timer is only relevent under ITU.
I32 sonusSs7TimerT39	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.45	Integer32	read-write	The Timer T39 is started when MCID request is sent. It is only relevent in the ITU.
I32 sonusSs7TimerT40	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.46	Integer32	read-write	The Timer T40 could be changed from its default using this entry.
I32 sonusSs7TimerTAcc	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.47	Integer32	read-write	Automatic Congestion Control Timer as per ANSI T1.113.4 - 1995. The value of the timer is 5 Seconds.
I32 sonusSs7TimerTCcr	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.48	Integer32	read-write	Continuity Check Request Timer. The value As per ANSI T1.113.4 - 1995 is 2 Seconds.
I32 sonusSs7TimerTCcrr	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.49	Integer32	read-write	Continuity Check Failed Recived. The value as per ANSI T1.113.4 - 1995 is 20 Seconds.
I32 sonusSs7TimerTCgb	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.50	Integer32	read-write	Timer started on recipt of a Circuit Group Block Message. The value as per ANSI T1.113.4 - 1995 is 5 Seconds.
I32 sonusSs7TimerTCra	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.51	Integer32	read-write	Timer started when Circuit Reservation Acknowledgment is sent. The time value as per ANSI T1.113.4 - 1995 is 20 seconds.
I32 sonusSs7TimerTCrm	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.52	Integer32	read-write	This timer is started when the circuit reservation message is sent. The value as per ANSI T1.113.4 - 1995 is 3 - 4 Seconds. The default is set to 4 seconds.
I32 sonusSs7TimerTCvt	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.53	Integer32	read-write	The Timer T CVT is started when the Circuit Validation Test message is sent. This message is only valid for ANSI.
I32 sonusSs7TimerTExm	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.54	Integer32	read-write	The Timer Exm,d is started when IAM is sent to the succeeding network. This timer has no relevence in the ITU. This timer is in milliseconds.
I32 sonusSs7TimerTGrs	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.55	Integer32	read-write	This timer is started when a circuit group reset message is received. This timer is only relevent in the ANSI network.
I32 sonusSs7TimerTHga	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.56	Integer32	read-write	This timer is started on recognition of carrier loss. It is only relevent in ANSI network. The valid range is 0 to 300 seconds.
I32 sonusSs7TimerTScga	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.57	Integer32	read-write	This timer is started when initial demand continuity check fails in the SCGA group. The valid range for this timer is 0 to 120 seconds.
I32 sonusSs7TimerTScgad	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.58	Integer32	read-write	This timer is started failure of demand continuity check in the SCGA group.
INT sonusSs7NodeProfileState	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.59	INTEGER	read-write	The administrative state of this object.
ROW sonusSs7NodeProfileRowStatus	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.60	RowStatus	read-write
INT sonusSs7NodeProfileNetworkInd	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.61	INTEGER	read-write	The setting of the Network Indicator used for this SS7 Node entry.
I32 sonusSs7SlsBits	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.62	Integer32	read-write	The number of SLS bits to use
I32 sonusSs7TimerTA	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.63	Integer32	read-write	The Bellcore specific timer TA is started when a RLC message is sent by the switch. The value of this timer is 0 to 1000 milliseconds.
I32 sonusSs7TimerTBlom	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.64	Integer32	read-write	The Bellcore specific timer TBlom is started when blocking a circuit due to a BLO, and after any call is released; used to notify maintenance.
I32 sonusSs7TimerTCotd	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.65	Integer32	read-write	The Bellcore specific timer TCOTd is started when sending IAM requesting continuity check. The value of this timer is in milliseconds.
I32 sonusSs7TimerTCotl	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.66	Integer32	read-write	The Bellcore specific timer TCOTl is started when receiving second COT coded failed, awaiting receipt of CCR.
I32 sonusSs7TimerTSus	1.3.6.1.4.1.2879.2.5.3.1.3.2.1.67	Integer32	read-write	The Bellcore specific timer TSUS is started when a SUS message is sent by the terminating switch, awaiting called party off-hook or REL.
sonusSs7ServicesMIBNotifications	1.3.6.1.4.1.2879.2.5.3.2
sonusSs7ServicesMIBNotificationsPrefix	1.3.6.1.4.1.2879.2.5.3.2.0
NTF sonusSs7NodeConnectionEstablishedNotification	1.3.6.1.4.1.2879.2.5.3.2.0.1			This trap indicates that a connection has been established to the specified SS7 gateway. Information provided by this trap includes the name of the connected SS7 node, the name of the SS7 gateway on which the node resides, and the type of SS7 service that has been established (ISUP or TCAP).
NTF sonusSs7NodeConnectionFailedNotification	1.3.6.1.4.1.2879.2.5.3.2.0.2			This trap indicates that an established connection to an SS7 gateway has failed. Information provided by this trap includes the name of the failed SS7 node, the name of the SS7 gateway on which the node resides, the type of SS7 service affected by this failure, and the reason why the connection has failed.
NTF sonusSs7NodeConnectionStateChangeNotification	1.3.6.1.4.1.2879.2.5.3.2.0.3			This trap indicates that an established connection to an SS7 gateway has changed state. Information provided by this trap includes the name of the affected SS7 node, the name of the SS7 gateway on which the node resides, the type of SS7 service affected by this failure, the new state of the node, and the reason for the state change.
NTF sonusSs7NodeMtpStateChangeNotification	1.3.6.1.4.1.2879.2.5.3.2.0.4			This trap indicates that a MTP state change event has been received from the SS7 gateway, affecting the specified destination (or remote) point code (DPC). Information provided by this trap includes the name of the affected SS7 node, the name of the SS7 gateway on which the node resides, the updated MTP state, and the DPC affected by this event.
sonusSs7ServicesMIBNotificationsObjects	1.3.6.1.4.1.2879.2.5.3.2.1
STR sonusSs7NodeServiceType	1.3.6.1.4.1.2879.2.5.3.2.1.1	DisplayString	read-only	The type of service supported by this SS7 node connection (ISUP or TCAP).
STR sonusSs7NodeStateChangeReason	1.3.6.1.4.1.2879.2.5.3.2.1.2	DisplayString	read-only	The reason why this SS7 node connection has changed state.
INT sonusSs7NodeCurrentStateEx	1.3.6.1.4.1.2879.2.5.3.2.1.3	INTEGER	read-only	The current state of this SS7 node connection.
NUM sonusSs7NodeAffectedPointCode	1.3.6.1.4.1.2879.2.5.3.2.1.4	PointCode	read-only	The SS7 point code affected by this MTP state change.

RFC description

Sonus SS7 gateway and node configuration MIB for managing Signaling System 7 network components and routing.

Start monitoring Sonus Networks (Ribbon Communications) signaling gateways/softswitches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SONUS-SS7-SERVICES-MIB