SIAE-CARRIER-AGGRL1-MIB

All MIBs › SIAE-CARRIER-AGGRL1-MIB

Organization: SIAE MICROELETTRONICA spa

Last Updated: 2016-08-23

Category: Microwave Radio - SIAE MICROELETTRONICA

Description: Manages SIAE MICROELETTRONICA carrier-level aggregation layer-1 configuration and throughput.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SIAE-CARRIER-AGGRL1-MIB?

SIAE-CARRIER-AGGRL1-MIB is a vendor MIB from SIAE MICROELETTRONICA for managing carrier-level Layer-1 aggregation on its microwave radio transmission equipment, part of the telecom microwave backhaul technology area, allowing multiple radio carriers to be combined into a single aggregated hybrid link. Although no object list was extracted, hybrid Layer-1 aggregation MIBs of this kind typically expose per-carrier configuration, aggregation group membership, and throughput/capacity statistics for the combined link. This data would be used to monitor hardware status of the radio carriers participating in an aggregation group and the resulting throughput, helping an operator detect a degraded or failed carrier reducing overall aggregate capacity, though specific object names cannot be confirmed here. It is a self-contained SIAE enterprise MIB, likely paired with other SIAE radio hardware and software MIBs for the same microwave platform. It is deployed by telecom operators running SIAE microwave radio backhaul links requiring higher aggregate capacity through carrier bonding, with the SIAE-CARRIER-AGGRL1-MIB MIB providing the corresponding management interface.

IPNetwork Monitor allows you to monitor SNMP objects defined in SIAE-CARRIER-AGGRL1-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

SIAE MICROELETTRONICA microwave radio

Monitoring Examples

No sample objects were available for this module, so a concrete polling scenario using real object names cannot be given; based on the module's stated purpose, an admin would typically expect a per-carrier aggregation membership table and an aggregate throughput/capacity object, but the specific object names cannot be confirmed from the available data.

What Can Be Monitored

carrier aggregation throughput (unconfirmed - no objects available)

Imported Objects

From IF-MIB

InterfaceIndexOrZero

From SIAE-TREE-MIB

siaeMib

OBJECT-IDENTITY

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
carrierAggr	1.3.6.1.4.1.3373.1103.104			Carrier hybrid aggregation management for SIAE equipments.
INT carrierAggrMibVersion	1.3.6.1.4.1.3373.1103.104.1	INTEGER	read-only	Numerical version of this module. The string version of this MIB have the following format: XX.YY.ZZ so, for example, the value 1 should be interpreted as 00.00.01 and the value 10001 should be interpreted as 01.00.01.
carrierAggrSensorTable	1.3.6.1.4.1.3373.1103.104.2		not-accessible	Table with Radio(s) interface(s) that can be associated to an entry of carrierAggrActuatorTable.
carrierAggrSensorEntry	1.3.6.1.4.1.3373.1103.104.2.1		not-accessible	A row in the carrierAggrSensorTable.
INT carrierAggrSensorIndex	1.3.6.1.4.1.3373.1103.104.2.1.1	INTEGER	read-only	This object identifies the index of carrierAggrSensorTable.
ROW carrierAggrSensorRowstatus	1.3.6.1.4.1.3373.1103.104.2.1.2	RowStatus	read-create	The status of this sensor entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value: SensorIfIndex must be set to a valid ifIndex number. Otherwise, the error inconsistentValue is returned on the attempt to set active this row. When this object is set to notInService changes may be made to carrierAggrSensorIfIndex. Other objects can be changed when carrierAggrSensorRowStatus is set to active. A sensor can not be deleted if there is any Actuator (see table carrierAggrActuatorTable) associated with it.
INT carrierAggrSensorAdminStatus	1.3.6.1.4.1.3373.1103.104.2.1.3	INTEGER	read-create	Administative status of the sensor. The value down(1) turns off all actuators associated with this sensor.
NUM carrierAggrSensorIfIndex	1.3.6.1.4.1.3373.1103.104.2.1.4	InterfaceIndexOrZero	read-create	This object accepts a greater than zero value to identify an interface in ifTable. Some parameters of the radio associated to this interface is monitored and a notification is sent to all connected actuators.
BIT carrierAggrSensorHitlessCapability	1.3.6.1.4.1.3373.1103.104.2.1.5	Bits	read-only	This capability is related to HITLESS Behaviour carrierAggrSensorHitlessBehaviour.
INT carrierAggrSensorHitlessBehaviour	1.3.6.1.4.1.3373.1103.104.2.1.6	INTEGER	read-create	The hitless behaviour. When enabled, data related to the current ACM zone is notified to an external N.E. aggregator, so it can dynamically exclude/include the data-flow without loss of frames. It can be enabled only if carrierAggrSensorHitlessCapability is available
INT carrierAggrSensorHitlessMode	1.3.6.1.4.1.3373.1103.104.2.1.7	INTEGER	read-create	The policy to select the hitless profile (i.e. the lowest one under which a N.E. aggregator excludes the carrier from an existing aggregation). auto(1): Tx Lower Profile + 1 is selected; manual(2): the value set in carrierAggrSensorHitlessProfile is selected.
INT carrierAggrSensorHitlessProfile	1.3.6.1.4.1.3373.1103.104.2.1.8	INTEGER	read-create	The hitless profile in case of carrierHyAggrHitlessBehaviour set as enabled and carrierHyAggrHitlessMode set as manual.
INT carrierAggrSensorHitlessStatus	1.3.6.1.4.1.3373.1103.104.2.1.9	INTEGER	read-only	The working zone of the radio link.
carrierAggrActuatorTable	1.3.6.1.4.1.3373.1103.104.3		not-accessible	Table with Lan(s) interface that can be associated to an entry of carrierAggrSensorTable.
carrierAggrActuatorEntry	1.3.6.1.4.1.3373.1103.104.3.1		not-accessible	A row in the carrierAggrActuatorTable.
INT carrierAggrActuatorIndex	1.3.6.1.4.1.3373.1103.104.3.1.1	INTEGER	read-only	This object identifies the carrier aggr Actuator inside the Network Element.
ROW carrierAggrActuatorRowStatus	1.3.6.1.4.1.3373.1103.104.3.1.2	RowStatus	read-create	The status of this entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value: carrierAggrActuatorIfIndex must be set to a valid ifIndex number and carrierAggrActuatorSensorIndex must be set to a valid sensor, Otherwise, the error inconsistentValue is returned on the attempt to set active this row. When set to notInService changes may be made to carrierAggrActuatorIfIndex and carrierAggrActuatorSensorIndex. Other objects can be changed when carrierAggrActuatorRowStatus is set to active.
INT carrierAggrActuatorAdminStatus	1.3.6.1.4.1.3373.1103.104.3.1.3	INTEGER	read-create	Administative status of the actuator. The value down(1) turns it off. Other actuators associated with the same sensor remain active.
NUM carrierAggrActuatorIfIndex	1.3.6.1.4.1.3373.1103.104.3.1.4	InterfaceIndexOrZero	read-create	This object accepts a greater than zero value to identify an interface in ifTable. The notify received from the connected sensor is forwarded to the remote aggregator to signal some anomalies on this aggregated flow.
I32 carrierAggrActuatorSensorIndex	1.3.6.1.4.1.3373.1103.104.3.1.5	Integer32	read-create	This object connects this actuator to a sensor.
IP carrierAggrActuatorConcIpAddr	1.3.6.1.4.1.3373.1103.104.3.1.6	IpAddress	read-only	This object is used to contain the Ip address of the equipment connected with this Lan (the concatenator unit)

RFC description

SIAE carrier hybrid aggregation management for radio and LAN interface link aggregation.

Start monitoring SIAE MICROELETTRONICA microwave radio (carrier-level Layer-1 hybrid aggregation status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SIAE-CARRIER-AGGRL1-MIB

What Is SIAE-CARRIER-AGGRL1-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description