RETIX-METROLAN-MIB

All MIBs › RETIX-METROLAN-MIB

Category: Legacy / Bridge Equipment

Description: Manages Retix MetroLAN Ethernet bridge configuration and forwarding table operations.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RETIX-METROLAN-MIB?

RETIX-METROLAN-MIB is a legacy enterprise MIB from Retix, an early-1990s networking equipment vendor, covering their MetroLAN family of Ethernet bridges. It defines configuration objects for bridge operation and the forwarding/filtering database used to switch Ethernet frames between ports. Its monitoring role centers on the operational status of the bridging function -- port up/down state, forwarding table entries/learning activity, and bridge-level configuration -- rather than deep hardware environmental sensors, reflecting the more limited management model of early Ethernet bridge products. As an Ethernet bridge MIB from that era it would typically be used alongside, or as a private-enterprise supplement to, the IETF Bridge MIB (RFC 1493 / dot1dBridge) rather than replacing it. It would have been deployed on Retix MetroLAN Ethernet bridges used in early enterprise LAN interconnection and metro-area bridging deployments. Engineers can download the RETIX-METROLAN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in RETIX-METROLAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Retix MetroLAN Ethernet bridges (legacy, discontinued vendor)

Monitoring Examples

No sample_objects or module_desc text were provided for this module in the available source, so specific object or table names cannot be responsibly cited; based on the short description, a network administrator would be expected to poll bridge forwarding-table and port-status objects to confirm learned MAC addresses and port states, but exact identifiers are not confirmed from available data.

What Can Be Monitored

bridge port status
forwarding/filtering database entries
bridge configuration parameters

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
DisplayString
Gauge
IpAddress
NetworkAddress
TimeTicks
enterprises

From RFC1213-MIB

mib-2

OIDs

OID symbolic	OID numeric	Type	Access	Description
atmBandwithGroup	1.3.6.1.2.1.37.1
INT atmBWG	1.3.6.1.2.1.37.2.5	INTEGER	read-write	Bandwidth group number. That paticular bandwidthgroup must be configured with a positive bandwidth
INT atmBWGBandwidth	1.3.6.1.2.1.37.1.1	INTEGER	read-write	The bandwidth amount (in Kbps) assigned to a specific bandwidth group. Total bandwidth for all eight groups can not exceed the maximum, which is 36880.
INT atmBWGConfig	1.3.6.1.2.1.37.1.2	INTEGER	write-only	this carry out the actual SET of the bandwidth group. a SYSTEM RESET will be executed for the changes in bandwidth group to take effect.
INT atmEncaps	1.3.6.1.2.1.37.2.6	INTEGER	read-write	Encapsulation
atmLogicalPort	1.3.6.1.2.1.37.2
INT atmPortConfig	1.3.6.1.2.1.37.2.7	INTEGER	read-write	this carry out the actual SET of the logical port. 0 deletes the existing port, 1 creates a new logical port
INT atmRX_VCI	1.3.6.1.2.1.37.2.1	INTEGER	read-write	Receive VCI #. can be set as the same as atmTX-VCI
INT atmRX_VPI	1.3.6.1.2.1.37.2.2	INTEGER	read-write	Receive VPI #. can be set as the same as atmTX-VPI
INT atmTX_VCI	1.3.6.1.2.1.37.2.3	INTEGER	read-write	Transmit VCI #. choose a unique number for each ATM logical port.
INT atmTX_VPI	1.3.6.1.2.1.37.2.4	INTEGER	read-write	Transmit VPI #.
INT ds3AISDetect	1.3.6.1.2.1.37.3.18	INTEGER	read-only	AISDetect stat
INT ds3AISDetectCntr	1.3.6.1.2.1.37.3.3	INTEGER	read-only	AISDetectCntr stat
INT ds3ATMOCD	1.3.6.1.2.1.37.3.10	INTEGER	read-only	ATMOCD stat
INT ds3BipolarSerialIO	1.3.6.1.2.1.37.3.21	INTEGER	read-write	Bipolar serial IO
INT ds3BPVErrCntr	1.3.6.1.2.1.37.3.9	INTEGER	read-only	BPVErrCntr stat
INT ds3ClearErrorCntr	1.3.6.1.2.1.37.3.19	INTEGER	write-only	SET this object will clear the Error Counters.
INT ds3CPErrCntr	1.3.6.1.2.1.37.3.7	INTEGER	read-only	CPErrCntr stat
INT ds3FEACGenNDetect	1.3.6.1.2.1.37.3.26	INTEGER	read-write	FEAC generation/detection
INT ds3FEBEGeneration	1.3.6.1.2.1.37.3.24	INTEGER	read-write	FEBE error generation
INT ds3FEBlockErrCntr	1.3.6.1.2.1.37.3.8	INTEGER	read-only	FEBlockErrCntr stat
INT ds3FErrCntr	1.3.6.1.2.1.37.3.5	INTEGER	read-only	FErrCntr stat
INT ds3FIFOOverflow	1.3.6.1.2.1.37.3.11	INTEGER	read-only	FIFOOverflow stat
ds3FrameDevice	1.3.6.1.2.1.37.3
INT ds3FrameLoss	1.3.6.1.2.1.37.3.15	INTEGER	read-only	FrameLoss stat
INT ds3GFCInsertion	1.3.6.1.2.1.37.3.20	INTEGER	read-write	Insertion of GFC bits
INT ds3LoopBack	1.3.6.1.2.1.37.3.25	INTEGER	read-write	LoopBack Mode
INT ds3NoDS3FrameCntr	1.3.6.1.2.1.37.3.2	INTEGER	read-only	NoDS3FrameCntr stat
INT ds3NoSignalCntr	1.3.6.1.2.1.37.3.1	INTEGER	read-only	NoSignalCntr stat
INT ds3PayloadScrambling	1.3.6.1.2.1.37.3.22	INTEGER	read-write	Payload scrambling
INT ds3PErrCntr	1.3.6.1.2.1.37.3.6	INTEGER	read-only	PErrCntr stat
INT ds3PLCPOverheadProc	1.3.6.1.2.1.37.3.23	INTEGER	read-write	PLCP overhead processing
INT ds3RAI	1.3.6.1.2.1.37.3.12	INTEGER	read-only	RAI stat
INT ds3RAICntr	1.3.6.1.2.1.37.3.13	INTEGER	read-only	RAICntr stat
INT ds3RcvEQ	1.3.6.1.2.1.37.3.27	INTEGER	read-write	Use internal receive equalizer
INT ds3SignalLoss	1.3.6.1.2.1.37.3.14	INTEGER	read-only	SignalLoss stat
INT ds3SyncLoss	1.3.6.1.2.1.37.3.16	INTEGER	read-only	SyncLoss stat
INT ds3XmitLevel	1.3.6.1.2.1.37.3.28	INTEGER	read-write	transmit level: use normal (low) or long (high) cables
INT ds3YellowAlarm	1.3.6.1.2.1.37.3.17	INTEGER	read-only	YellowAlarm stat
INT ds3YellowAlarmCntr	1.3.6.1.2.1.37.3.4	INTEGER	read-only	YellowAlarmCntr stat
metroLanDS3ATM	1.3.6.1.2.1.37
metroLanSS	1.3.6.1.4.1.72.20
portVLANEntry	1.3.6.1.4.1.72.20.4.2.1		not-accessible	a VLAN entry containing portID, VLANID, ...
portVLANTable	1.3.6.1.4.1.72.20.4.2		not-accessible	Table of port based VLAN configurations. Entries (rows) are added to the table by issuing a SET command with the EnableAdd value for the portVLANEntryEdit object. The new row is created using the instantiations.
retix	1.3.6.1.4.1.72
INT slipEnable	1.3.6.1.4.1.72.20.5.1	INTEGER	read-write	enable/disable SLIP
IP slipHostIP	1.3.6.1.4.1.72.20.5.2	IpAddress	read-write	SLIP Remote IP Addr
INT ssBaseBootFWVer	1.3.6.1.4.1.72.20.2.1	INTEGER	read-only	Version number of current boot firmware
INT ssBaseModule	1.3.6.1.4.1.72.20.1.1	INTEGER	read-only	Identifies the type of main board card type
INT ssBaseSoftVer	1.3.6.1.4.1.72.20.2.2	INTEGER	read-only	Version number of current software
ssBaseUnit	1.3.6.1.4.1.72.20.2
INT ssErrorLog	1.3.6.1.4.1.72.20.2.3	INTEGER	read-write	A stored value indicating that the unit has experienced a fault. Log information is formatted as a four digit hex number. Set to zero to clear the logged fault. Record this value and call Retix technical support.
INT ssIO1Module	1.3.6.1.4.1.72.20.1.2	INTEGER	read-only	I/O 1 card type
INT ssIO2Module	1.3.6.1.4.1.72.20.1.3	INTEGER	read-only	I/O 2 card type
ssSlip	1.3.6.1.4.1.72.20.5
ssStakBus	1.3.6.1.4.1.72.20.3
INT ssStkBusIOPort	1.3.6.1.4.1.72.20.3.1	INTEGER	read-only	which I/O port is StakBus installed. (only 1 stakbus per system is allowed)
INT ssStkBusNodeAddr	1.3.6.1.4.1.72.20.3.3	INTEGER	read-only	Module ID for StakBus card
INT ssStkBusRingOp	1.3.6.1.4.1.72.20.3.4	INTEGER	read-only	StakBus Ring OperationalStatus
INT ssStkBusSpeed	1.3.6.1.4.1.72.20.3.2	INTEGER	read-only	StakBus speed. 175000000, or 0 if no StakBus card installed
ssUnitProfile	1.3.6.1.4.1.72.20.1
ssVirtualLan	1.3.6.1.4.1.72.20.4
INT ssVLANEnDisable	1.3.6.1.4.1.72.20.4.1	INTEGER	read-write	Globally enable/disable VLAN for the system
INT ssVLANEntryEdit	1.3.6.1.4.1.72.20.4.2.1.3	INTEGER	read-write	When set to enableAdd(1) the instantiations will be used to create a new table entry (row). Existing entries can be disabled(2) or deleted (3).
INT ssVLANEntryPortID	1.3.6.1.4.1.72.20.4.2.1.1	INTEGER	read-write	Port ID
INT ssVLANEntryVLANID	1.3.6.1.4.1.72.20.4.2.1.2	INTEGER	read-write	Vlan ID

RFC description

Manages ATM bandwidth groups, DS3/ATM boards, virtual LANs, and SLIP configuration on MetroLAN switches.

Start monitoring Retix MetroLAN Ethernet bridges, legacy discontinued vendor (bridge/forwarding-database status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RETIX-METROLAN-MIB

What Is RETIX-METROLAN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

RFC description