RBBPROVISIONING-MIB

All MIBs › RBBPROVISIONING-MIB

Organization: IETF ADSL MIB Working Group

Last Updated: 1999-09-27

Category: DSL and Broadband Access

Description: Manages broadband remote access provisioning parameters for ADSL subscriber lines.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is RBBPROVISIONING-MIB?

RBBPROVISIONING-MIB is a vendor-neutral, standards-oriented MIB for provisioning broadband customer premises equipment (CPE), built primarily around xDSL services (including ATM-transported DSL) though not limited to that technology. It exposes configuration/provisioning data -- the parameters needed to set up and activate a subscriber's broadband line and CPE -- rather than live traffic counters or hardware sensor readings. Its monitoring role is chiefly around service/configuration status: confirming a subscriber line's provisioning parameters have been correctly applied and the CPE has picked them up, which is a software/configuration-state check rather than hardware health monitoring. It is closely tied to xDSL standards work and complements DSL physical-layer MIBs (e.g., HDSL2-SHDSL-MIB, ADSL-LINE-MIB) which report the actual line performance and sync status. It is deployed by broadband access providers provisioning DSL modems/routers at the customer premises, often alongside a broadband remote access server (BRAS) or DSLAM. Engineers implementing or auditing this functionality typically reference the RBBPROVISIONING-MIB RFC/standard documentation for the authoritative specification.

IPNetwork Monitor allows you to monitor SNMP objects defined in RBBPROVISIONING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB, not tied to a specific manufacturer
xDSL customer premises equipment (CPE)/modem-router

Monitoring Examples

sample_objects is empty for this module, so no concrete object/table names can be confirmed. Based on the module description, an operator would use this MIB to push and verify xDSL/ATM provisioning parameters to CPE, then check that the provisioning state reflects "active" or "complete" to confirm a subscriber line came up correctly after a service order. Without object names available, this remains a general scenario rather than an object-level example.

What Can Be Monitored

broadband line provisioning parameters
CPE provisioning/activation status

Imported Objects

From ATM-TC-MIB

AtmAddr
AtmConnCastType
AtmConnKind
AtmServiceCategory
AtmTrafficDescrParamIndex
AtmVcIdentifier
AtmVpIdentifier

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
enterprises
mib-2

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
rbbProvMIB	1.3.6.1.4.1.4839.32			This is the MIB Module for provisioning of broadband customer premises equipment, specifically xDSL-related services. While not precluding other broadband technology, the MIB has been constructed around existing xDSL facilities, including ATM transports.
rbbProvMIBObjects	1.3.6.1.4.1.4839.32.1
rbbServicesGroup	1.3.6.1.4.1.4839.32.1.1
srvServicesTable	1.3.6.1.4.1.4839.32.1.1.1		not-accessible	This table contains a sequence of rows where each row describes a particular service that is available to a broadband customer. The service availability expressed in this table is assumed to be valid only for customers served by this management infrastructure, and may differ on a regional basis, even within the same overall access network.
srvServiceEntry	1.3.6.1.4.1.4839.32.1.1.1.1		not-accessible	This object defines the individual rows in the SRV services table (srvServicesTable)
RBB srvServiceIdentifier	1.3.6.1.4.1.4839.32.1.1.1.1.1	RBBServiceID	read-create	A unique object identifier (OID) value uniquely representing a particular service.
RBB srvServiceName	1.3.6.1.4.1.4839.32.1.1.1.1.2	RBBServiceName	read-create	A human-readable name string that identifies a service to an end-user
RBB srvServiceProvider	1.3.6.1.4.1.4839.32.1.1.1.1.3	RBBServiceProvider	read-create	A human-readable name string that identifies the public or private sponsoring entity for a particular service.
RBB srvServiceStatus	1.3.6.1.4.1.4839.32.1.1.1.1.4	RBBServiceStatus	read-create	An INTEGER enumeration describing the current availability status of a particular service. NOTE: This status implies different semantics than that used by srvServiceSubrStatus
ATM srvServiceConnType	1.3.6.1.4.1.4839.32.1.1.1.1.5	AtmConnKind	read-create	An enumerated value describing the type of endpoint address used to refer to a particular service, as well as whether the CPE should be an initiator or target during the connection.
INT srvServiceQOSType	1.3.6.1.4.1.4839.32.1.1.1.1.6	INTEGER	read-create	The quality-of-service to be associated with a connection to a particular service.
INT srvServiceSpeedReq	1.3.6.1.4.1.4839.32.1.1.1.1.7	INTEGER	read-create	The bandwidth or speed (in bits-per-second) necessary to realize a particular service
INT srvServiceLatencyReq	1.3.6.1.4.1.4839.32.1.1.1.1.8	INTEGER	read-create	An enumerated value that describes whether or not a particular service has special latency requirements associated to effectively realize the service.
RBB srvServiceURL	1.3.6.1.4.1.4839.32.1.1.1.1.9	RBBURLType	read-create	A URL string associated with a particular service. A service may be provisioned with an associated URL that can be used either as a provisioning link or as a potentially advertising source for the service.
STR srvServiceDescr	1.3.6.1.4.1.4839.32.1.1.1.1.10	DisplayString	read-create	A human-readable string used to provide a brief description for a particular service.
RBB srvAdminContact	1.3.6.1.4.1.4839.32.1.1.1.1.11	RBBMailAddr	read-create	A string representing the email address of an administrator contact for the particular service. This could either be a contact used to request new service or options associated with the service, OR, could be used as a support contact address for an existing subscription.
ROW srvRowInfo	1.3.6.1.4.1.4839.32.1.1.1.1.12	RowStatus	read-create	Maintains row status information for this table
rbbSubGroup	1.3.6.1.4.1.4839.32.1.2
rbbSubTable	1.3.6.1.4.1.4839.32.1.2.1		not-accessible	This table contains a sequence of rows where each row describes a particular service subscription between an end-user CPE and a particular service.
rbbSubEntry	1.3.6.1.4.1.4839.32.1.2.1.1		not-accessible	This object defines the individual rows in the subscription table (rbbSubTable)
OID rbbSubVendor	1.3.6.1.4.1.4839.32.1.2.1.1.1	OBJECT IDENTIFIER	read-create	The Vendor part of the index that uniquely identifies this CPE
RBB rbbSubModel	1.3.6.1.4.1.4839.32.1.2.1.1.3	RBBVendorModel	read-create	The Model part of the index that uniquely identifies a CPE
STR rbbSubSerialNumber	1.3.6.1.4.1.4839.32.1.2.1.1.4	DisplayString	read-create	The serial number part of the index that uniquely identifies a CPE
RBB rbbSubServiceIdentifier	1.3.6.1.4.1.4839.32.1.2.1.1.5	RBBServiceID	read-create	An Index value referring to an entry in the rbbServicesTable. This is the service-side in the customer/service subscription association.
OID rbbSubVPI	1.3.6.1.4.1.4839.32.1.2.1.1.6	AtmVpIdentifier	read-create	The virtual path identifier to be used in the establishment of a PVC to a particular service, if the service is PVC- based.
OID rbbSubVCI	1.3.6.1.4.1.4839.32.1.2.1.1.7	AtmVcIdentifier	read-create	The virtual circuit identifier to be used in the establishment of a PVC to a particular service, if the service is PVC-based.
ATM rbbSubAddr	1.3.6.1.4.1.4839.32.1.2.1.1.8	AtmAddr	read-create	The end-system address to be used in the establishment of an SVC to a particular service, if the service is SVC-based.
RBB rbbSubStatus	1.3.6.1.4.1.4839.32.1.2.1.1.9	RBBServiceStatus	read-create	The current status of this subscription, currently defined as up, down, or suspended.
ROW rbbSubRowInfo	1.3.6.1.4.1.4839.32.1.2.1.1.10	RowStatus	read-create
rbbCPEGroup	1.3.6.1.4.1.4839.32.1.3
rbbCPETable	1.3.6.1.4.1.4839.32.1.3.1		not-accessible	This table contains a sequence of rows where each row describes a particular CPE that has identified itself to the management framework.
rbbCPEEntry	1.3.6.1.4.1.4839.32.1.3.1.1		not-accessible	This object defines the individual rows in the CPE table (rbbCPETable)
RBB rbbCPEAuthValue	1.3.6.1.4.1.4839.32.1.3.1.1.1	RBBCPEAuthType	read-create	A unique identifier that uniquely identifies a particular customer or end-user
OID rbbCPEVendorOID	1.3.6.1.4.1.4839.32.1.3.1.1.2	OBJECT IDENTIFIER	read-create	A unique object identifier that identifies a particular CPE vendor
RBB rbbCPEVendorModel	1.3.6.1.4.1.4839.32.1.3.1.1.3	RBBVendorModel	read-create
INT rbbCPEStatus	1.3.6.1.4.1.4839.32.1.3.1.1.4	INTEGER	read-create	An integer enumeration that identifies the current status of the CPE device
INT rbbCPESubCount	1.3.6.1.4.1.4839.32.1.3.1.1.5	INTEGER	read-create	An integer value representing the number of service subscriptions that exist in the subscription table for this customer
INT rbbCPESubAggrSpeed	1.3.6.1.4.1.4839.32.1.3.1.1.6	INTEGER	read-create	The total aggregate bandwidth required by all active subscriptions for this CPE customer.
RBB rbbCPECustContact	1.3.6.1.4.1.4839.32.1.3.1.1.7	RBBMailAddr	read-create	The email address for the individual at the customer premises that is responsible for the broadband service.
RBB rbbCPESerialNumber	1.3.6.1.4.1.4839.32.1.3.1.1.8	RBBCPESerialNumber	read-create	The unique hardware address or serial number associated with the CPE
INT rbbCPETrapEnable	1.3.6.1.4.1.4839.32.1.3.1.1.9	INTEGER	read-create	A boolean value representing whether or not service-related traps are enabled or disabled for this CPE device.
RBB rbbCPECurrentImage	1.3.6.1.4.1.4839.32.1.3.1.1.10	RBBURLType	read-create	A URL string pointing to the current image that is installed in this particular CPE/customer site
IP rbbCPEIpAddress	1.3.6.1.4.1.4839.32.1.3.1.1.11	IpAddress	read-create
ROW rbbCPERowInfo	1.3.6.1.4.1.4839.32.1.3.1.1.12	RowStatus	read-create
rbbVendorGroup	1.3.6.1.4.1.4839.32.1.4
rbbVendorTable	1.3.6.1.4.1.4839.32.1.4.1		not-accessible	Vendor table describing types of CPE supported, and associated CPE management details.
rbbVendorEntry	1.3.6.1.4.1.4839.32.1.4.1.1		not-accessible	Each row describes a particular vendor model of CPE
OID rbbVendorOID	1.3.6.1.4.1.4839.32.1.4.1.1.1	OBJECT IDENTIFIER	read-create	A unique object identifier value associated with a particular vendor of CPE
RBB rbbVendorModel	1.3.6.1.4.1.4839.32.1.4.1.1.2	RBBVendorModel	read-create	A human-readable string representing the model number for a particular vendor's CPE device
RBB rbbVendorImageURL	1.3.6.1.4.1.4839.32.1.4.1.1.3	RBBURLType	read-create	A URL string representing the most current version of firmware available for this CPE model
ROW rbbVendorRowInfo	1.3.6.1.4.1.4839.32.1.4.1.1.4	RowStatus	read-create
C32 rbbSrvGrpSerialNumber	1.3.6.1.4.1.4839.32.1.5	Counter32	read-only
C32 rbbSubGrpSerialNumber	1.3.6.1.4.1.4839.32.1.6	Counter32	read-only
C32 rbbCPEGrpSerialNumber	1.3.6.1.4.1.4839.32.1.7	Counter32	read-only
C32 rbbVendorGrpSerialNumber	1.3.6.1.4.1.4839.32.1.8	Counter32	read-only
rbbNotifyGroup	1.3.6.1.4.1.4839.32.1.12
NTF rbbSubNotify	1.3.6.1.4.1.4839.32.1.12.1			This notification indicates that a new subscription has been added to, or when a subscription has been deleted from the rbbSubTable in the rbbSubGroup. The notification includes which specific index was added so that the manager does not have to implement a search for changes.
NTF rbbPowerUpNotify	1.3.6.1.4.1.4839.32.1.12.2

RFC description

Broadband CPE (customer premises equipment) provisioning for xDSL services and ATM transport configurations.

Start monitoring vendor-neutral, standards-based MIB, xDSL customer-premises equipment/modem-router provisioning with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download RBBPROVISIONING-MIB

What Is RBBPROVISIONING-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description