PRVT-CFM-MIB

All MIBs › PRVT-CFM-MIB

Organization: BATM Advanced Communication

Last Updated: 2014-04-17

Category: Carrier Ethernet

Description: Manages BATM Advanced Communication IEEE 802.1ag Connectivity Fault Management (CFM) MEP/MIP configuration and OAM results.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PRVT-CFM-MIB?

PRVT-CFM-MIB is a BATM Advanced Communication proprietary extension MIB implementing IEEE 802.1ag Connectivity Fault Management (CFM), a Carrier Ethernet OAM technology area used to detect link and service faults in Ethernet networks. It exposes configuration and operational data for CFM Maintenance End Points (MEPs) and Maintenance Intermediate Points (MIPs), including the maintenance domain/association stack, direction, and associated interface and MAC address. Its monitoring value is software/protocol-state health rather than physical hardware -- it lets an operator confirm CFM sessions are correctly stacked on the right interface and service, and detect faults or misconfigurations in the fault-management overlay itself (e.g. a stack shutdown via prvtCfmShutdown). As a vendor extension of the IEEE 802.1ag standard, it depends directly on that standard's CFM data model and is meant to be used alongside the standard CFM MIB. It is deployed on BATM carrier Ethernet switches/aggregation nodes used by service providers for Ethernet OAM and SLA fault detection, and operators typically consult a PRVT-CFM-MIB MIB Browser view to map out these stack and MEP objects before writing polling scripts.

IPNetwork Monitor allows you to monitor SNMP objects defined in PRVT-CFM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BATM Advanced Communication carrier Ethernet switches/aggregation nodes

Monitoring Examples

An operator would poll prvtCfmStackTable entries (prvtCfmStackInterfaceIndex, prvtCfmStackMdLevel, prvtCfmStackDirection, prvtCfmStackMaName, prvtCfmStackMepId, prvtCfmStackMacAddress) to verify a MEP is correctly stacked at the expected maintenance domain level on a given interface. Checking prvtCfmUpdateInterval alongside prvtCfmShutdown would reveal whether CFM monitoring on a stack has been disabled, which would explain a loss of fault visibility on that service. Notifications from prvtCfmMIBNotifications would be watched for CFM-detected connectivity faults between MEPs.

What Can Be Monitored

CFM MEP/MIP stack configuration
maintenance domain level and direction
MEP MAC address
CFM monitoring shutdown state
connectivity fault notifications

Imported Objects

From IF-MIB

InterfaceIndex

From PRVT-SWITCH-MIB

switch

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TAddress
TDomain
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using prvtCfmMepCcmSequenceErrors OID:

Select a BATM carrier Ethernet switches/aggregation node as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type prvtCfmMepCcmSequenceErrors into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of out-of-sequence CCMs received from all remote MEPs. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
prvtCfmMIB	1.3.6.1.4.1.738.1.5.131			Prvt extension of Connectivity Fault Management module for managing IEEE 802.1ag
prvtCfmMIBNotifications	1.3.6.1.4.1.738.1.5.131.0
NTF prvtCfm1wJitterThreshold	1.3.6.1.4.1.738.1.5.131.0.1			This trap should be sent whenever the one way jitter on a CFM test will surpass one of the 2 defined thresholds.
NTF prvtCfmJitterThreshold	1.3.6.1.4.1.738.1.5.131.0.2			This trap should be sent whenever the two way jitter on a CFM test will surpass one of the 2 defined thresholds.
NTF prvtCfmFrameLossThreshold	1.3.6.1.4.1.738.1.5.131.0.3			This trap should be sent whenever the frame loss on a CFM test will surpass one of the 2 defined thresholds.
NTF prvtCfmLatencyThreshold	1.3.6.1.4.1.738.1.5.131.0.4			This trap should be sent whenever the latency on a CFM test will surpass one of the 2 defined thresholds.
NTF prvtCfmUnexpectedPriority	1.3.6.1.4.1.738.1.5.131.0.5			References to in the [G.8021/Y.1341] : Unexpected Priority defect (dUNPr) The Unexpected Priority defect is calculated at the ETH layer. It detects the configuration of different Priorities for CCM at different MEPs belonging to the same MEG.
NTF prvtCfmFaultAlarm	1.3.6.1.4.1.738.1.5.131.0.6			A MEP has a persistent defect condition. A notification (fault alarm) is sent to the management entity with the OID of the MEP that has detected the fault. Whenever a MEP has a persistent defect, it may or may not generate a Fault Alarm to warn the system administrator of the problem, as controlled by the MEP Fault Notification Generator State Machine and associated Managed Objects. Only the highest-priority defect, as shown in Table 20-1, is reported in the Fault Alarm. If a defect with a higher priority is raised after a Fault Alarm has been issued, another Fault Alarm is issued. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the MEP reporting the defect by the indices in the OID of the prvtCfmMepHighestPrDefect variable in the notification: prvtCfmMdName - Also the index of the MEP's Maintenance Domain table entry (prvtCfmMdTable). prvtCfmMaName - Also an index (with the MD table index) of the MEP's Maintenance Association table entry (prvtCfmMaTable), prvtCfmMepIdentifier - MEP Identifier and final index into the MEP table (prvtCfmMepTable).
NTF prvtCfmAisLckRecieved	1.3.6.1.4.1.738.1.5.131.0.7			A MEP may generate a AIS/LCK notification each time its AIS/LCK condition is activated.
NTF prvtCfmAisLckCleared	1.3.6.1.4.1.738.1.5.131.0.8			The notification is sent each time AIS/LCK condition is cleared.
NTF prvtCfmFaultAlarmCleared	1.3.6.1.4.1.738.1.5.131.0.9			A MEP's persistent defect condition has cleared. A notification is sent to the management entity with the OID of the MEP that has cleared the fault. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the MEP by the indices in the OID of the prvtCfmMepIdentifier variable in the notification: prvtCfmMdName - Also the index of the MEP's Maintenance Domain table entry (prvtCfmMdTable). prvtCfmMaName - Also an index (with the MD table index) of the MEP's Maintenance Association table entry (prvtCfmMaTable), prvtCfmMepIdentifier - MEP Identifier and final index into the MEP table (prvtCfmMepTable).
prvtCfmMIBObjects	1.3.6.1.4.1.738.1.5.131.1
U32 prvtCfmUpdateInterval	1.3.6.1.4.1.738.1.5.131.1.1	Unsigned32	read-write	Time between monitoring parameters update (in seconds). A value of 0 suspends the monitoring task and a value different from 0 resumes it. Default is 20 seconds.
T/F prvtCfmShutdown	1.3.6.1.4.1.738.1.5.131.1.2	TruthValue	read-write	Set to 'true' to disable CFM, or to 'false', to enable.
prvtCfmStack	1.3.6.1.4.1.738.1.5.131.1.3
prvtCfmStackTable	1.3.6.1.4.1.738.1.5.131.1.3.1		not-accessible	There is one CFM Stack table per bridge. It permits the retrieval of information about the Maintenance Points configured on any given interface.
prvtCfmStackEntry	1.3.6.1.4.1.738.1.5.131.1.3.1.1		not-accessible	The Stack table entry
NUM prvtCfmStackInterfaceIndex	1.3.6.1.4.1.738.1.5.131.1.3.1.1.1	InterfaceIndex	not-accessible	This object represents the Bridge Port or aggregated port on which MEPs or MHFs might be configured. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable, and rearrange the prvtCfmStackTable, so that it indexes the entry in the interface table with the same value of ifAlias that it indexed before the system restart. If no such entry exists, then the system SHALL delete all entries in the prvtCfmStackTable with the interface index.
U32 prvtCfmStackServiceIdOrNone	1.3.6.1.4.1.738.1.5.131.1.3.1.1.2	Unsigned32	not-accessible	VLAN ID to which the MP is attached, or 0, if none.
PRV prvtCfmStackMdLevel	1.3.6.1.4.1.738.1.5.131.1.3.1.1.3	PrvtCfmMDLevelTC	not-accessible	MD Level of the Maintenance Point.
PRV prvtCfmStackDirection	1.3.6.1.4.1.738.1.5.131.1.3.1.1.4	PrvtCfmMpDirection	not-accessible	Direction in which the MP faces on the Bridge Port
NUM prvtCfmStackMdName	1.3.6.1.4.1.738.1.5.131.1.3.1.1.5	PrvtCfmMaintDomainNameOrNone	read-only	The index of the Maintenance Domain in the prvtCfmMdTable to which the MP is associated, or zero-length, if none.
NUM prvtCfmStackMaName	1.3.6.1.4.1.738.1.5.131.1.3.1.1.6	PrvtCfmMaintAssocNameOrNone	read-only	The index of the MA in the prvtCfmMaTable to which the MP is associated, or zero-length, if none.
U32 prvtCfmStackMepId	1.3.6.1.4.1.738.1.5.131.1.3.1.1.7	Unsigned32	read-only	If an MEP is configured, the MEPID, else 0
MAC prvtCfmStackMacAddress	1.3.6.1.4.1.738.1.5.131.1.3.1.1.8	MacAddress	read-only	MAC address of the MP.
prvtCfmMd	1.3.6.1.4.1.738.1.5.131.1.4
prvtCfmMdTable	1.3.6.1.4.1.738.1.5.131.1.4.2		not-accessible	The Maintenance Domain table. Each row in the table represents a different Maintenance Domain. A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.
prvtCfmMdEntry	1.3.6.1.4.1.738.1.5.131.1.4.2.1		not-accessible	The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage.
NUM prvtCfmMdName	1.3.6.1.4.1.738.1.5.131.1.4.2.1.1	PrvtCfmMaintDomainName	not-accessible	The Maintenance Domain name. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain. Clause 3.24 defines a Maintenance Domain name as the identifier, unique over the domain for which CFM is to protect against accidental concatenation of Service Instances, of a particular Maintenance Domain.
ROW prvtCfmMdRowStatus	1.3.6.1.4.1.738.1.5.131.1.4.2.1.2	RowStatus	read-create	The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
PRV prvtCfmMdLevel	1.3.6.1.4.1.738.1.5.131.1.4.2.1.4	PrvtCfmMDLevelTC	read-create	The Maintenance Domain Level.
NUM prvtCfmMdFormat	1.3.6.1.4.1.738.1.5.131.1.4.2.1.5	PrvtCfmMaintDomainNameType	read-create	The type (and thereby format) of the Maintenance Domain Name.
PRV prvtCfmMdMhfCreation	1.3.6.1.4.1.738.1.5.131.1.4.2.1.6	PrvtCfmMhfCreationDef	read-create	Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value defMHFdefer is not allowed.
PRV prvtCfmMdMhfIdPermission	1.3.6.1.4.1.738.1.5.131.1.4.2.1.7	PrvtCfmIdPermissionDef	read-create	Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value sendIdDefer is not allowed.
prvtCfmMa	1.3.6.1.4.1.738.1.5.131.1.5
prvtCfmMaTable	1.3.6.1.4.1.738.1.5.131.1.5.1		not-accessible	The Maintenance Association table. Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance. The writable objects in this table need to be persistent upon reboot or restart of a device. Table includes extra variables needed for Y.1731 support and service awareness
prvtCfmMaEntry	1.3.6.1.4.1.738.1.5.131.1.5.1.1		not-accessible	prvtCfmMaEntry
NUM prvtCfmMaName	1.3.6.1.4.1.738.1.5.131.1.5.1.1.1	PrvtCfmMaintAssocName	not-accessible	The Short Maintenance Association name. This name must be unique within a maintenance domain.
ROW prvtCfmMaRowStatus	1.3.6.1.4.1.738.1.5.131.1.5.1.1.2	RowStatus	read-create	The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
U32 prvtCfmMaServiceId	1.3.6.1.4.1.738.1.5.131.1.5.1.1.4	Unsigned32	read-create	The primary service ID attached to this MA
I32 prvtCfmMaVlanId	1.3.6.1.4.1.738.1.5.131.1.5.1.1.5	Integer32	read-create	The primary vlan ID attached to this MA
PRV prvtCfmMaMhfCreation	1.3.6.1.4.1.738.1.5.131.1.5.1.1.6	PrvtCfmMhfCreation	read-create	Indicates if the Management entity can create MHFs (MIP Half Function) for this MA.
PRV prvtCfmMaPermission	1.3.6.1.4.1.738.1.5.131.1.5.1.1.7	PrvtCfmIdPermission	read-create	Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this MA.
NUM prvtCfmMaFormat	1.3.6.1.4.1.738.1.5.131.1.5.1.1.8	PrvtCfmMaintAssocNameType	read-create	The type (and thereby format) of the Maintenance Association Name.
NUM prvtCfmMaCcmInterval	1.3.6.1.4.1.738.1.5.131.1.5.1.1.9	PrvtCfmCcmInterval	read-create	Interval between CCM transmissions to be used by all MEPs in the MA.
T/F prvtCfmMaAisLckReceive	1.3.6.1.4.1.738.1.5.131.1.5.1.1.10	TruthValue	read-create	Turn the AIS & LCK features on/off.
U32 prvtCfmMaAisLckLevel	1.3.6.1.4.1.738.1.5.131.1.5.1.1.11	Unsigned32	read-create	The MD level at which AIS & LCK frames will be sent.
INT prvtCfmMaAisLckInterval	1.3.6.1.4.1.738.1.5.131.1.5.1.1.12	INTEGER	read-create	The time interval at which AIS and LCK frames will be sent
U32 prvtCfmMaAisLckPriority	1.3.6.1.4.1.738.1.5.131.1.5.1.1.13	Unsigned32	read-create	COS parameter for the outgoing AIS & LCK frames.
U32 prvtCfmMaClearConnectivity	1.3.6.1.4.1.738.1.5.131.1.5.1.1.15	Unsigned32	read-create	The ID of the MEP to be cleared from the MEP table, or 0 for all
prvtCfmMep	1.3.6.1.4.1.738.1.5.131.1.6
prvtCfmMepTable	1.3.6.1.4.1.738.1.5.131.1.6.1		not-accessible	The Maintenance Association End Point (MEP) table. Each row in the table represents a different MEP. A MEP is an actively managed CFM entity, associated with a specific DSAP of a Service Instance, which can generate and receive CFM PDUs and track any responses. It is an end point of a single Maintenance Association, and is an endpoint of a separate Maintenance Entity for each of the other MEPs in the same Maintenance Association (802.1ag clause 3.18). This table uses three indices. The first two indices are the indices of the Maintenance Domain and MA tables, the reason being that a MEP is always related to an MA and Maintenance Domain. The MEP table also stores all the managed objects for sending LBM and LTM. LBM Managed objects LBM Managed objects in the MEP table enables the management entity to initiate transmission of Loopback messages. It will signal the MEP that it should transmit some number of Loopback messages and detect the detection (or lack thereof) of the corresponding Loopback messages. Steps to use entries in this table: 1) Set prvtCfmMepTransmitLbmStatus to true 2) Set the target by: a) target mep - configue prvtCfmMepTransmitLbmDestIsMepId on true and then configure prvtCfmMepTransmitLbmDestMepId with the remote mep id b) target mac - configue prvtCfmMepTransmitLbmDestIsMepId on false and then configure prvtCfmMepTransmitLbmDestMacAddress with the remote device mac address 3) Setup the different data to be sent (number of messages, optional TLVs,...). 4) Record the current values of prvtCfmMepLbrIn, prvtCfmMepLbrInOutOfOrder, and prvtCfmMepLbrBadMsdu. 6) Change prvtCfmMepTransmitLbmStatus value to false to initiate transmission of Loopback messages. 7) Check the value of prvtCfmMepTransmitLbmResultOK to find out if the operation was successfully initiated or not. 8) If prvtCfmMepTransmitLbmInfinite is set to false you can monitor the value of prvtCfmMepTransmitLbmRemainingMessages. When it reaches 0, the last LBM has been transmitted and the operation is finished. Wait an additional 5 seconds to ensure that all LBRs have been returned. 9) If prvtCfmMepTransmitLbmInfinite is set to true you must stop the operation yourself by setting prvtCfmMepTransmitLbmStatus to true. 10) Compare prvtCfmMepLbrIn, prvtCfmMepLbrInOutOfOrder, and prvtCfmMepLbrBadMsdu to their old values from step 4, above, to get the results of the test. LTM Managed objects The LTM Managed objects in the MEP table are used in a manner similar to that described for LBM transmission, above. Upon successfully initiating the transmission, the variables pvrtCfmMepTransmitLtmSeqNumber and prvtCfmMepTransmitLtmEgressIdentifier return the information required to recover the results of the LTM from the prvtCfmLtrTable.
prvtCfmMepEntry	1.3.6.1.4.1.738.1.5.131.1.6.1.1		not-accessible	prvtCfmMepEntry
PRV prvtCfmMepIdentifier	1.3.6.1.4.1.738.1.5.131.1.6.1.1.1	PrvtCfmMepId	read-only	Integer that is unique among all the MEPs in the same MA. Other definition is: a small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.19). MEP Identifier is also known as the MEPID.
ROW prvtCfmMepRowStatus	1.3.6.1.4.1.738.1.5.131.1.6.1.1.2	RowStatus	read-create	The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
NUM prvtCfmMepInterfaceIndex	1.3.6.1.4.1.738.1.5.131.1.6.1.1.3	InterfaceIndex	read-create	This object is the interface index (from ifTable) of either a bridge port, or an aggregated IEEE 802.1 link, to which the MEP is attached.
PRV prvtCfmMepDirection	1.3.6.1.4.1.738.1.5.131.1.6.1.1.4	PrvtCfmMpDirection	read-create	The direction in which the MEP faces on the Bridge port.
T/F prvtCfmMepShutdown	1.3.6.1.4.1.738.1.5.131.1.6.1.1.5	TruthValue	read-create	Administrative state of the MEP The value 'true' will shutdown/disable the MEP. The value 'false' will enable the MEP.
PRV prvtCfmMepFngState	1.3.6.1.4.1.738.1.5.131.1.6.1.1.6	PrvtCfmFngState	read-only	Current state of the MEP Fault Notification Generator State Machine.
T/F prvtCfmMepCciEnabled	1.3.6.1.4.1.738.1.5.131.1.6.1.1.7	TruthValue	read-create	If set to true, the MEP will generate CCM messages.
U32 prvtCfmMepCcmLtmPriority	1.3.6.1.4.1.738.1.5.131.1.6.1.1.8	Unsigned32	read-create	The priority value for CCMs and LTMs transmitted by the MEP. Default Value is the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default value for this variable from the priority regeneration table by extracting the highest priority value in this table on this MEPs bridge port. (1 is lowest, then 2, then 0, then 3-7).
MAC prvtCfmMepMacAddress	1.3.6.1.4.1.738.1.5.131.1.6.1.1.9	MacAddress	read-only	MAC address of the MEP.
PRV prvtCfmMepLowPrDef	1.3.6.1.4.1.738.1.5.131.1.6.1.1.10	PrvtCfmLowestAlarmPri	read-create	An integer value specifying the lowest priority defect that is allowed to generate fault alarm.
PRV prvtCfmMepHighestPrDefect	1.3.6.1.4.1.738.1.5.131.1.6.1.1.11	PrvtCfmHighestDefectPri	read-only	The highest priority defect that has been present since the MEPs Fault Notification Generator State Machine was last in the FNG_RESET state.
BIT prvtCfmMepDefects	1.3.6.1.4.1.738.1.5.131.1.6.1.1.12	Bits	read-only	A vector of Boolean error conditions from Table 20-1, any of which may be true.
OCT prvtCfmMepErrorCcmLastFailure	1.3.6.1.4.1.738.1.5.131.1.6.1.1.13	OCTET STRING	read-only	The last-received CCM that triggered an DefErrorCCM fault.
OCT prvtCfmMepXconCcmLastFailure	1.3.6.1.4.1.738.1.5.131.1.6.1.1.14	OCTET STRING	read-only	The last-received CCM that triggered a DefXconCCM fault.
C32 prvtCfmMepCcmSequenceErrorsEx	1.3.6.1.4.1.738.1.5.131.1.6.1.1.15	Counter32	read-only	The total number of out-of-sequence CCMs received from all remote MEPs.
C32 prvtCfmMepCciSentCcms	1.3.6.1.4.1.738.1.5.131.1.6.1.1.16	Counter32	read-only	Total number of Continuity Check messages transmitted.
U32 prvtCfmMepNextLbmTransId	1.3.6.1.4.1.738.1.5.131.1.6.1.1.17	Unsigned32	read-only	Next sequence number/transaction identifier to be sent in a Loopback message. This sequence number can be zero because it wraps around.
C32 prvtCfmMepLbrIn	1.3.6.1.4.1.738.1.5.131.1.6.1.1.18	Counter32	read-only	Total number of valid, in-order Loopback Replies received.
C32 prvtCfmMepLbrInOutOfOrder	1.3.6.1.4.1.738.1.5.131.1.6.1.1.19	Counter32	read-only	The total number of valid, out-of-order Loopback Replies received.
C32 prvtCfmMepLbrBadMsdu	1.3.6.1.4.1.738.1.5.131.1.6.1.1.20	Counter32	read-only	The total number of LBRs received whose mac_service_data_unit did not match (except for the OpCode) that of the corresponding LBM (20.2.3).
U32 prvtCfmMepLtmNextSeqNumber	1.3.6.1.4.1.738.1.5.131.1.6.1.1.21	Unsigned32	read-only	Next transaction identifier/sequence number to be sent in a Linktrace message. This sequence number can be zero because it wraps around.
C32 prvtCfmMepUnexpLtrIn	1.3.6.1.4.1.738.1.5.131.1.6.1.1.22	Counter32	read-only	The total number of unexpected LTRs received (20.39.1).
C32 prvtCfmMepLbrOut	1.3.6.1.4.1.738.1.5.131.1.6.1.1.23	Counter32	read-only	Total number of Loopback Replies transmitted.
T/F prvtCfmMepTransmitLbmStatus	1.3.6.1.4.1.738.1.5.131.1.6.1.1.24	TruthValue	read-create	A Boolean flag set to true by the bridge port to indicate that another LBM may be transmitted. Reset to false by the MEP Loopback Initiator State Machine.
MAC prvtCfmMepTransmitLbmDestMacAddress	1.3.6.1.4.1.738.1.5.131.1.6.1.1.25	MacAddress	read-create	The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column prvtCfmMepTransmitLbmDestIsMepId is 'false'.
PRV prvtCfmMepTransmitLbmDestMepId	1.3.6.1.4.1.738.1.5.131.1.6.1.1.26	PrvtCfmMepIdOrZero	read-create	The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the column prvtCfmMepTransmitLbmDestIsMepId is 'true'.
T/F prvtCfmMepTransmitLbmDestIsMepId	1.3.6.1.4.1.738.1.5.131.1.6.1.1.27	TruthValue	read-create	True indicates that MEPID of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission.
I32 prvtCfmMepTransmitLbmMessages	1.3.6.1.4.1.738.1.5.131.1.6.1.1.28	Integer32	read-create	The number of Loopback messages to be transmitted.
OCT prvtCfmMepTransmitLbmDataTlv	1.3.6.1.4.1.738.1.5.131.1.6.1.1.29	OCTET STRING	read-create	An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent.
I32 prvtCfmMepTransmitLbmVlanPriority	1.3.6.1.4.1.738.1.5.131.1.6.1.1.30	Integer32	read-create	Priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. The default value is CCM priority.
T/F prvtCfmMepTransmitLbmVlanDropEnable	1.3.6.1.4.1.738.1.5.131.1.6.1.1.31	TruthValue	read-create	Drop Enable bit value to be used in the VLAN tag, if present in the transmitted frame. For more information about VLAN Drop Enable, please check IEEE 802.1ad.
T/F prvtCfmMepTransmitLbmResultOK	1.3.6.1.4.1.738.1.5.131.1.6.1.1.32	TruthValue	read-only	Indicates the result of the operation: - true The Loopback Message(s) will be (or has been) sent. - false The Loopback Message(s) will not be sent.
U32 prvtCfmMepTransmitLbmSeqNumber	1.3.6.1.4.1.738.1.5.131.1.6.1.1.33	Unsigned32	read-only	The Loopback Transaction Identifier (prvtCfmMepNextLbmTransId) of the first LBM (to be) sent. The value returned is undefined if prvtCfmMepTransmitLbmResultOK is false.
T/F prvtCfmMepTransmitLtmStatus	1.3.6.1.4.1.738.1.5.131.1.6.1.1.34	TruthValue	read-create	A Boolean flag set to true by the bridge port to indicate that another LTM may be transmitted. In order to start linktrace following step should be executed: 1.Verify CFM connectivity 2.Set prvtCfmMepTransmitLtmTargetIsMepId to TRUE (if using target Mep) 3.Set prvtCfmMepTransmitLtmTargetMepId with the remote Mep Id 4.Set prvtCfmMepTransmitLtmTimeout (timeout for LTM packets) 5.Set prvtCfmMepTransmitLtmStatus to TRUE
BIT prvtCfmMepTransmitLtmFlags	1.3.6.1.4.1.738.1.5.131.1.6.1.1.35	Bits	read-create	The flags field for LTMs transmitted by the MEP.
MAC prvtCfmMepTransmitLtmTargetMacAddress	1.3.6.1.4.1.738.1.5.131.1.6.1.1.36	MacAddress	read-create	The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column prvtCfmMepTransmitLtmTargetIsMepId is 'false'.
PRV prvtCfmMepTransmitLtmTargetMepId	1.3.6.1.4.1.738.1.5.131.1.6.1.1.37	PrvtCfmMepIdOrZero	read-create	An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association This address will be used if the value of the column prvtCfmMepTransmitLtmTargetIsMepId is 'true'.
T/F prvtCfmMepTransmitLtmTargetIsMepId	1.3.6.1.4.1.738.1.5.131.1.6.1.1.38	TruthValue	read-create	True indicates that MEPID of the target MEP is used for Linktrace transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission.
U32 prvtCfmMepTransmitLtmTtl	1.3.6.1.4.1.738.1.5.131.1.6.1.1.39	Unsigned32	read-create	The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 by each Linktrace Responder that handles the LTM. The value returned in the LTR is one less than that received in the LTM. If the LTM TTL is 0 or 1, the LTM is not forwarded to the next hop, and if 0, no LTR is generated.
T/F prvtCfmMepTransmitLtmResult	1.3.6.1.4.1.738.1.5.131.1.6.1.1.40	TruthValue	read-only	Indicates the result of the operation: - true The Linktrace Message will be (or has been) sent. - false The Linktrace Message will not be sent
U32 prvtCfmMepTransmitLtmSeqNumber	1.3.6.1.4.1.738.1.5.131.1.6.1.1.41	Unsigned32	read-only	The LTM Transaction Identifier (prvtCfmMepLtmNextSeqNumber) of the LTM sent. The value returned is undefined if prvtCfmMepTransmitLtmResult is false.
OCT prvtCfmMepTransmitLtmEgressIdentifier	1.3.6.1.4.1.738.1.5.131.1.6.1.1.42	OCTET STRING	read-create	Identifies the MEP Linktrace Initiator that is originating, or the Linktrace Responder that is forwarding, this LTM. The low-order six octets contain a 48-bit IEEE MAC address unique to the system in which the MEP Linktrace Initiator or Linktrace Responder resides. The high-order two octets contain a value sufficient to uniquely identify the MEP Linktrace Initiator or Linktrace Responder within that system. For most Bridges, the address of any MAC attached to the Bridge will suffice for the low-order six octets, and 0 for the high-order octets. In some situations, e.g. if multiple virtual Bridges utilizing emulated LANs are implemented in a single physical system, the high-order two octets can be used to differentiate among the transmitting entities. The value returned is undefined if prvtCfmMepTransmitLtmResult is false.
T/F prvtCfmMepAlarmSupressed	1.3.6.1.4.1.738.1.5.131.1.6.1.1.43	TruthValue	read-only	A boolean showing if an AIS or LCK packet was received from a lower level
T/F prvtCfmMepAisCondition	1.3.6.1.4.1.738.1.5.131.1.6.1.1.44	TruthValue	read-only	AIS condition Is true by detection of signal fail condition at a Server layer or reception of AIS at a server (sub-) layer MEP [AIS condition/Rec. ITU-T Y.1731] Respectively AIS condition Exit criteria: 'During an interval equal to 3.5 times the AIS transmission period indicated in the AIS frames received earlier, the MEP does not receive AIS frames or, when ETH-CC is used, upon clearing of LOC defect at MEP' /Appendix I/Rec. ITU-T Y.1731 If prvtCfmMaAisLckLevel is configured the MEP should send AIS packets
T/F prvtCfmMepLckCondition	1.3.6.1.4.1.738.1.5.131.1.6.1.1.45	TruthValue	read-only	A boolean showing if the MEP should lock the service towards the client and send LCK packets
INT prvtCfmMepAisLifetime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.46	INTEGER	read-only	The lifetime of the last received AIS packet
INT prvtCfmMepLckLifetime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.47	INTEGER	read-only	The lifetime of the last received LCK packet
T/F prvtCfmMepTransmitMcastLbm	1.3.6.1.4.1.738.1.5.131.1.6.1.1.48	TruthValue	read-create	A boolean to control sending Y.1731 multicast loopback.
T/F prvtCfmMepTransmitLbmInfinite	1.3.6.1.4.1.738.1.5.131.1.6.1.1.49	TruthValue	read-create	A boolean to control sending LBMs continuously until the operation is explicitly stopped by setting this back to false
U32 prvtCfmMepTransmitLbmDelay	1.3.6.1.4.1.738.1.5.131.1.6.1.1.50	Unsigned32	read-create	An amount of time to wait between sent LBMs (in seconds).
U32 prvtCfmMepTransmitLbmTimeout	1.3.6.1.4.1.738.1.5.131.1.6.1.1.51	Unsigned32	read-create	An amount of time to wait after the last sent LBM if no LBR is received (in seconds).
U32 prvtCfmMepTransmitLtmTimeout	1.3.6.1.4.1.738.1.5.131.1.6.1.1.52	Unsigned32	read-create	An amount of time to wait after the last sent LTM if no LTR is received (in seconds).
U32 prvtCfmMepTransmitLbmSentPkts	1.3.6.1.4.1.738.1.5.131.1.6.1.1.53	Unsigned32	read-only	Number of successfully sent packets in the current LBM session.
U32 prvtCfmMepTransmitLbmSuccessRate	1.3.6.1.4.1.738.1.5.131.1.6.1.1.54	Unsigned32	read-only	Success rate of the current LBM session (in percentage*100).
U32 prvtCfmMepTransmitLbmMinTime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.55	Unsigned32	read-only	Minimum LBR response time (in msec).
U32 prvtCfmMepTransmitLbmAvgTime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.56	Unsigned32	read-only	Average LBR response time (in msec).
U32 prvtCfmMepTransmitLbmMaxTime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.57	Unsigned32	read-only	Maximum LBR response time (in msec).
U32 prvtCfmMepFngAlarmTime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.58	Unsigned32	read-create	The time that defects must be present before a Fault Alarm is issued (fngAlarmTime. 20.33.3) (default 2.5s).
U32 prvtCfmMepFngResetTime	1.3.6.1.4.1.738.1.5.131.1.6.1.1.59	Unsigned32	read-create	The time that defects must be absent before re-enabling a Fault Alarm (fngResetTime, 20.33.4) (default 10s).
I32 prvtCfmMepTransmitLbmRemainingMessages	1.3.6.1.4.1.738.1.5.131.1.6.1.1.60	Integer32	read-only	The number of LBMs (Loopback messages) to be transmitted
T/F prvtCfmMepTransmitLbmCurrentStatus	1.3.6.1.4.1.738.1.5.131.1.6.1.1.61	TruthValue	read-only	A Boolean flag set to true by the bridge port to indicate that another LBM may be transmitted. Reset to false by the MEP Loopback Initiator State Machine.
prvtCfmMepDbTable	1.3.6.1.4.1.738.1.5.131.1.6.2		not-accessible	The MEP Database. A database, maintained by every MEP, that maintains received information about other MEPs in the Maintenance Domain. The SMI does not allow to state in a MIB that an object in a table is an array. The solution is to take the index (or indices) of the first table and add one or more indices.
prvtCfmMepDbEntry	1.3.6.1.4.1.738.1.5.131.1.6.2.1		not-accessible	The MEP Database table entry.
U32 prvtCfmMepDbRMepIdentifier	1.3.6.1.4.1.738.1.5.131.1.6.2.1.1	Unsigned32	not-accessible	Maintenance association End Point Identifier of a remote MEP whose information from the MEP Database is to be returned.
PRV prvtCfmMepDbRMepState	1.3.6.1.4.1.738.1.5.131.1.6.2.1.2	PrvtCfmRemoteMepState	read-only	The operational state of the remote MEP IFF State machines.
TIM prvtCfmMepDbRMepFailedOkTime	1.3.6.1.4.1.738.1.5.131.1.6.2.1.3	TimeStamp	read-only	The time (SysUpTime) at which the IFF Remote MEP state machine last entered either the RMEP_FAILED or RMEP_OK state.
MAC prvtCfmMepDbMacAddress	1.3.6.1.4.1.738.1.5.131.1.6.2.1.4	MacAddress	read-only	The MAC address of the remote MEP.
T/F prvtCfmMepDbRdi	1.3.6.1.4.1.738.1.5.131.1.6.2.1.5	TruthValue	read-only	State of the RDI bit in the last received CCM (true for RDI=1), or false if none has been received.
PRV prvtCfmMepDbPortStatusTlv	1.3.6.1.4.1.738.1.5.131.1.6.2.1.6	PrvtCfmPortStatus	read-only	An enumerated value of the Port status TLV received in the last CCM from the remote MEP or the default value psNoPortStateTLV indicating either no CCM has been received, or that nor port status TLV was received in the last CCM.
NUM prvtCfmMepDbInterfaceStatusTlv	1.3.6.1.4.1.738.1.5.131.1.6.2.1.7	PrvtCfmInterfaceStatus	read-only	An enumerated value of the Interface status TLV received in the last CCM from the remote MEP or the default value isNoInterfaceStatus TLV indicating either no CCM has been received, or that no interface status TLV was received in the last CCM.
LLD prvtCfmMepDbChassisIdSubtype	1.3.6.1.4.1.738.1.5.131.1.6.2.1.8	LldpChassisIdSubtype	read-only	This object specifies the format of the Chassis ID received in the last CCM.
LLD prvtCfmMepDbChassisId	1.3.6.1.4.1.738.1.5.131.1.6.2.1.9	LldpChassisId	read-only	The Chassis ID. The format of this object is determined by the value of the prvtCfmLtrChassisIdSubtype object.
TDO prvtCfmMepDbManAddressDomain	1.3.6.1.4.1.738.1.5.131.1.6.2.1.10	TDomain	read-only	The TDomain that identifies the type and format of the related prvtCfmMepDbManAddress object, used to access the SNMP agent of the system transmitting the CCM. Received in the CCM Sender ID TLV from that system. Typical values will be one of (not all inclusive) list: snmpUDPDomain (from SNMPv2-TM, RFC3417) snmpIeee802Domain (from SNMP-IEEE802-TM-MIB, RFC4789) The value 'zeroDotZero' (from RFC2578) indicates 'no LTR Sender ID TLV received', in which case the related object prvtCfmMepDbManAddress must have a zero-length OCTET STRING as a value.
ADR prvtCfmMepDbManAddress	1.3.6.1.4.1.738.1.5.131.1.6.2.1.11	TAddress	read-only	The TAddress that can be used to access the SNMP agent of the system transmitting the CCM, received in the CCM Sender ID TLV from that system. If the related object prvtCfmMepDbManAddressDomain contains the value 'zeroDotZero', this object prvtCfmMepDbManAddress must have a zero-length OCTET STRING as a value.
prvtCfmLtrTable	1.3.6.1.4.1.738.1.5.131.1.6.3		not-accessible	This table extends the MEP table and contains a list of Linktrace replies received by a specific MEP in response to a linktrace message. SNMP SMI does not allow to state in a MIB that an object in a table is an array. The solution is to take the index (or indices) of the first table and add one or more indices.
prvtCfmLtrEntry	1.3.6.1.4.1.738.1.5.131.1.6.3.1		not-accessible	The Linktrace Reply table entry.
U32 prvtCfmLtrSeqNumber	1.3.6.1.4.1.738.1.5.131.1.6.3.1.1	Unsigned32	not-accessible	Transaction identifier/Sequence number returned by a previous transmit linktrace message command, indicating which LTM's response is going to be returned.
U32 prvtCfmLtrReceiveOrder	1.3.6.1.4.1.738.1.5.131.1.6.3.1.2	Unsigned32	not-accessible	An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. prvtCfmLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.
U32 prvtCfmLtrTtl	1.3.6.1.4.1.738.1.5.131.1.6.3.1.3	Unsigned32	read-only	TTL field value for a returned LTR.
T/F prvtCfmLtrForwarded	1.3.6.1.4.1.738.1.5.131.1.6.3.1.4	TruthValue	read-only	Indicates if a LTM was forwarded by the responding MP, as returned in the 'FwdYes' flag of the flags field.
T/F prvtCfmLtrTerminalMep	1.3.6.1.4.1.738.1.5.131.1.6.3.1.5	TruthValue	read-only	A boolean value stating whether the forwarded LTM reached a MEP enclosing its MA, as returned in the Terminal MEP flag of the Flags field.
OCT prvtCfmLtrLastEgressIdentifier	1.3.6.1.4.1.738.1.5.131.1.6.3.1.6	OCTET STRING	read-only	An octet field holding the Last Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Last Egress Identifier identifies the MEP Linktrace Initiator that originated, or the Linktrace Responder that forwarded, the LTM to which this LTR is the response. This is the same value as the Egress Identifier TLV of that LTM.
OCT prvtCfmLtrNextEgressIdentifier	1.3.6.1.4.1.738.1.5.131.1.6.3.1.7	OCTET STRING	read-only	An octet field holding the Next Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Next Egress Identifier Identifies the Linktrace Responder that transmitted this LTR, and can forward the LTM to the next hop. This is the same value as the Egress Identifier TLV of the forwarded LTM, if any. If the FwdYes bit of the Flags field is false, the contents of this field are undefined, i.e. any value can be transmitted, and the field is ignored by the receiver.
PRV prvtCfmLtrRelay	1.3.6.1.4.1.738.1.5.131.1.6.3.1.8	PrvtCfmRelayActionFieldValue	read-only	Value returned in the Relay Action field.
LLD prvtCfmLtrChassisIdSubtype	1.3.6.1.4.1.738.1.5.131.1.6.3.1.9	LldpChassisIdSubtype	read-only	This object specifies the format of the Chassis ID returned in the Sender ID TLV of the LTR, if any. This value is meaningless if the prvtCfmLtrChassisId has a length of 0.
LLD prvtCfmLtrChassisId	1.3.6.1.4.1.738.1.5.131.1.6.3.1.10	LldpChassisId	read-only	The Chassis ID returned in the Sender ID TLV of the LTR, if any. The format of this object is determined by the value of the prvtCfmLtrChassisIdSubtype object.
TDO prvtCfmLtrManAddressDomain	1.3.6.1.4.1.738.1.5.131.1.6.3.1.11	TDomain	read-only	The TDomain that identifies the type and format of the related prvtCfmLtrManAddress object, used to access the SNMP agent of the system transmitting the LTR. Received in the LTR Sender ID TLV from that system. Typical values will be one of (not all inclusive) list: snmpUDPDomain (from SNMPv2-TM, RFC3417) snmpIeee802Domain (from SNMP-IEEE802-TM-MIB, RFC4789) The value 'zeroDotZero' (from RFC2578) indicates 'no LTR Sender ID TLV received', in which case the related object prvtCfmLtrManAddress must have a zero-length OCTET STRING as a value.
ADR prvtCfmLtrManAddress	1.3.6.1.4.1.738.1.5.131.1.6.3.1.12	TAddress	read-only	The TAddress that can be used to access the SNMP agent of the system transmitting the CCM, received in the CCM Sender ID TLV from that system. If the related object prvtCfmLtrManAddressDomain contains the value 'zeroDotZero', this object prvtCfmLtrManAddress must have a zero-length OCTET STRING as a value.
PRV prvtCfmLtrIngress	1.3.6.1.4.1.738.1.5.131.1.6.3.1.13	PrvtCfmIngressActionFieldValue	read-only	The value returned in the Ingress Action Field of the LTM.
MAC prvtCfmLtrIngressMac	1.3.6.1.4.1.738.1.5.131.1.6.3.1.14	MacAddress	read-only	MAC address returned in the ingress MAC address field.
LLD prvtCfmLtrIngressPortIdSubtype	1.3.6.1.4.1.738.1.5.131.1.6.3.1.15	LldpPortIdSubtype	read-only	Format of the Ingress Port ID.
LLD prvtCfmLtrIngressPortId	1.3.6.1.4.1.738.1.5.131.1.6.3.1.16	LldpPortId	read-only	Ingress Port ID. The format of this object is determined by the value of the prvtCfmLtrIngressPortIdSubtype object.
PRV prvtCfmLtrEgress	1.3.6.1.4.1.738.1.5.131.1.6.3.1.17	PrvtCfmEgressActionFieldValue	read-only	The value returned in the Egress Action Field of the LTM.
MAC prvtCfmLtrEgressMac	1.3.6.1.4.1.738.1.5.131.1.6.3.1.18	MacAddress	read-only	MAC address returned in the egress MAC address field.
LLD prvtCfmLtrEgressPortIdSubtype	1.3.6.1.4.1.738.1.5.131.1.6.3.1.19	LldpPortIdSubtype	read-only	Format of the egress Port ID.
LLD prvtCfmLtrEgressPortId	1.3.6.1.4.1.738.1.5.131.1.6.3.1.20	LldpPortId	read-only	Egress Port ID. The format of this object is determined by the value of the prvtCfmLtrEgressPortIdSubtype object.
OCT prvtCfmLtrOrganizationSpecificTlv	1.3.6.1.4.1.738.1.5.131.1.6.3.1.21	OCTET STRING	read-only	All Organization specific TLVs returned in the LTR, if any. Includes all octets including and following the TLV Length field of each TLV, concatenated together.
U32 prvtCfmLtrTime	1.3.6.1.4.1.738.1.5.131.1.6.3.1.22	Unsigned32	read-only	Remote MPs response time in milliseconds.
MAC prvtCfmLtrSourceMac	1.3.6.1.4.1.738.1.5.131.1.6.3.1.23	MacAddress	read-only	MAC address that originated the LTR.
prvtCfmLbrTable	1.3.6.1.4.1.738.1.5.131.1.6.4		not-accessible	Table contains loopback results following the last loopback operation.
prvtCfmLbrEntry	1.3.6.1.4.1.738.1.5.131.1.6.4.1		not-accessible	prvtCfmLbrEntry
U32 prvtCfmLbrSeqNumber	1.3.6.1.4.1.738.1.5.131.1.6.4.1.1	Unsigned32	not-accessible	Transaction identifier/Sequence number of the received LBR.
U32 prvtCfmLbrReceiveOrder	1.3.6.1.4.1.738.1.5.131.1.6.4.1.2	Unsigned32	not-accessible	An index to distinguish among multiple LBRs with the same LBR Transaction Identifier field value. This situation can appear in the case of multicast loopback.
U32 prvtCfmLbrTime	1.3.6.1.4.1.738.1.5.131.1.6.4.1.3	Unsigned32	read-only	Remote MEPs response time in milliseconds.
MAC prvtCfmLbrMacAddress	1.3.6.1.4.1.738.1.5.131.1.6.4.1.4	MacAddress	read-only	Remote MEPs mac address. For unicast loopback this is the same as prvtCfmMepTransmitLbmDestMacAddress, but for multicast loopback there will be different entries.
T/F prvtCfmLbrBadMsdu	1.3.6.1.4.1.738.1.5.131.1.6.4.1.5	TruthValue	read-only	Result of the Data TLV verification.
prvtCfmProfile	1.3.6.1.4.1.738.1.5.131.1.7
NUM prvtCfmProfileTableNextIndex	1.3.6.1.4.1.738.1.5.131.1.7.1	PrvtCfmIndexIntegerNextFree	read-only	This object contains an unused value for prvtCfmProfileIndex in the prvtCfmProfileTable or a zero to indicate that none exist.
prvtCfmProfileTable	1.3.6.1.4.1.738.1.5.131.1.7.2		not-accessible	Table contains loopback results from all remote MEPs in the MA.
prvtCfmProfileEntry	1.3.6.1.4.1.738.1.5.131.1.7.2.1		not-accessible	Entry in profile table
U32 prvtCfmProfileIndex	1.3.6.1.4.1.738.1.5.131.1.7.2.1.1	Unsigned32	not-accessible	Table index.
ROW prvtCfmProfileRowStatus	1.3.6.1.4.1.738.1.5.131.1.7.2.1.2	RowStatus	read-create	The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
OCT prvtCfmProfileDescr	1.3.6.1.4.1.738.1.5.131.1.7.2.1.3	OCTET STRING	read-create	A description for this profile. This field must be unique among all profiles.
U32 prvtCfmProfilePriority	1.3.6.1.4.1.738.1.5.131.1.7.2.1.4	Unsigned32	read-create	802.1p class-of-service setting.
U32 prvtCfmProfileRate	1.3.6.1.4.1.738.1.5.131.1.7.2.1.5	Unsigned32	read-create	Number of Request packets to send each time.
U32 prvtCfmProfileSize	1.3.6.1.4.1.738.1.5.131.1.7.2.1.6	Unsigned32	read-create	Size of data TLV included in probe packets (in octets).
U32 prvtCfmProfileBucketSize	1.3.6.1.4.1.738.1.5.131.1.7.2.1.7	Unsigned32	read-create	Number of the results to save for results calculation.
U32 prvtCfmProfile1wJitterError	1.3.6.1.4.1.738.1.5.131.1.7.2.1.8	Unsigned32	read-create	Specifies one-way jitter error values to monitor in milliseconds.
U32 prvtCfmProfile1wJitterWarning	1.3.6.1.4.1.738.1.5.131.1.7.2.1.9	Unsigned32	read-create	Specifies one-way jitter warning values to monitor in milliseconds.
U32 prvtCfmProfileJitterError	1.3.6.1.4.1.738.1.5.131.1.7.2.1.10	Unsigned32	read-create	Specifies round-trip jitter error values to monitor in milliseconds.
U32 prvtCfmProfileJitterErrorPeriod	1.3.6.1.4.1.738.1.5.131.1.7.2.1.11	Unsigned32	read-create	Specifies the duration jitter occurs in seconds.
U32 prvtCfmProfileJitterWarning	1.3.6.1.4.1.738.1.5.131.1.7.2.1.12	Unsigned32	read-create	Specifies round-trip jitter warning values to monitor in milliseconds. If set value is greater than the jitter-error it means that the warning is disabled.
U32 prvtCfmProfileJitterWarningPeriod	1.3.6.1.4.1.738.1.5.131.1.7.2.1.13	Unsigned32	read-create	Specifies the duration jitter occurs in seconds.
U32 prvtCfmProfileFrameLossError	1.3.6.1.4.1.738.1.5.131.1.7.2.1.14	Unsigned32	read-create	Specifies round-trip frame-loss error values to monitor. The default is frame-loss of 10% is reported.
U32 prvtCfmProfileFrameLossWarning	1.3.6.1.4.1.738.1.5.131.1.7.2.1.15	Unsigned32	read-create	Specifies round-trip frame-loss warning values to monitor. The default is frame-loss of 8% is reported. If set value is greater than the frame-loss-error it means that the warning is disable.
U32 prvtCfmProfileLatencyError	1.3.6.1.4.1.738.1.5.131.1.7.2.1.16	Unsigned32	read-create	Specifies round-trip latency error values to monitor in milliseconds.
U32 prvtCfmProfileLatencyErrorPeriod	1.3.6.1.4.1.738.1.5.131.1.7.2.1.17	Unsigned32	read-create	Specifies the duration latency increase occurs in seconds.
U32 prvtCfmProfileLatencyWarning	1.3.6.1.4.1.738.1.5.131.1.7.2.1.18	Unsigned32	read-create	Specifies round-trip latency error values to monitor in milliseconds. If set value is greater than the latency-error it means that the warning is disabled.
U32 prvtCfmProfileLatencyWarningPeriod	1.3.6.1.4.1.738.1.5.131.1.7.2.1.19	Unsigned32	read-create	Specifies the duration latency increase occurs.
T/F prvtCfmProfileOneWayJitterEnabled	1.3.6.1.4.1.738.1.5.131.1.7.2.1.20	TruthValue	read-create	Specify if one-way jitter is monitored.
T/F prvtCfmProfileTwoWayJitterEnabled	1.3.6.1.4.1.738.1.5.131.1.7.2.1.21	TruthValue	read-create	Specify if two-way jitter is monitored.
T/F prvtCfmProfileFramelossEnabled	1.3.6.1.4.1.738.1.5.131.1.7.2.1.22	TruthValue	read-create	Specify if frame-loss is monitored.
T/F prvtCfmProfileLatencyEnabled	1.3.6.1.4.1.738.1.5.131.1.7.2.1.23	TruthValue	read-create	Specify if two-way latency is monitored.
prvtCfmProcess	1.3.6.1.4.1.738.1.5.131.1.8
prvtCfmProcessTable	1.3.6.1.4.1.738.1.5.131.1.8.1		not-accessible	Private extension of prvtCfmMaTable. Controls the two-way monitoring process for MEP's in the MA.
prvtCfmProcessEntry	1.3.6.1.4.1.738.1.5.131.1.8.1.1		not-accessible	prvtCfmProcessEntry
U32 prvtCfmProcessIndex	1.3.6.1.4.1.738.1.5.131.1.8.1.1.1	Unsigned32	not-accessible	Table index.
ROW prvtCfmProcessRowStatus	1.3.6.1.4.1.738.1.5.131.1.8.1.1.2	RowStatus	read-create	The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.
U32 prvtCfmProcessProfileIndex	1.3.6.1.4.1.738.1.5.131.1.8.1.1.3	Unsigned32	read-create	Index of the monitoring profile to be used.
OCT prvtCfmProcessName	1.3.6.1.4.1.738.1.5.131.1.8.1.1.4	OCTET STRING	read-only	The name of the process. Should be unique per domain/MA
T/F prvtCfmProcessShutdown	1.3.6.1.4.1.738.1.5.131.1.8.1.1.5	TruthValue	read-create	The value 'true' will disable two-way monitoring process for MEP's in the MA.
U32 prvtCfmProcessRepeatInterval	1.3.6.1.4.1.738.1.5.131.1.8.1.1.6	Unsigned32	read-create	Repeating frequency of the monitoring process.
INT prvtCfmProcessPacketType	1.3.6.1.4.1.738.1.5.131.1.8.1.1.7	INTEGER	read-create	Use CFM Loopback or Y.1731 LMMs and DMMs packets.
U32 prvtCfmProcessUnreturnedPkts	1.3.6.1.4.1.738.1.5.131.1.8.1.1.8	Unsigned32	read-only	Number of requests for which a reply hasn't been received. These packets will be counted as lost when they enter timeout.
prvtCfmProcessResultTable	1.3.6.1.4.1.738.1.5.131.1.8.2		not-accessible	Table contains process results.
prvtCfmProcessResultEntry	1.3.6.1.4.1.738.1.5.131.1.8.2.1		not-accessible	prvtCfmProcessResultEntry
U32 prvtCfmProcessResultOneWayJitter	1.3.6.1.4.1.738.1.5.131.1.8.2.1.1	Unsigned32	read-only	One way jitter calculated for a specific remote MEP in milliseconds
U32 prvtCfmProcessResultTwoWayJitter	1.3.6.1.4.1.738.1.5.131.1.8.2.1.2	Unsigned32	read-only	Two way jitter calculated for a specific remote MEP in milliseconds
U32 prvtCfmProcessResultLatency	1.3.6.1.4.1.738.1.5.131.1.8.2.1.3	Unsigned32	read-only	Two way latency calculated for a specific remote MEP in milliseconds
U32 prvtCfmProcessResultFrameloss	1.3.6.1.4.1.738.1.5.131.1.8.2.1.4	Unsigned32	read-only	Two way frameloss calculated for a specific remote MEP in units of hundredths of percent. Note: When prvtCfmProcessResultFrameloss has value of 10000, all the values of prvtCfmProcessResultOneWayJitter, prvtCfmProcessResultTwoWayJitter and prvtCfmProcessResultLatency are irrelevant.
prvtCfmMaAisLckVlan	1.3.6.1.4.1.738.1.5.131.1.9
prvtCfmMaAisLckVlanTable	1.3.6.1.4.1.738.1.5.131.1.9.1		not-accessible	Table includes extra variables needed for AIS/LCK configurable vlans
prvtCfmMaAisLckVlanEntry	1.3.6.1.4.1.738.1.5.131.1.9.1.1		not-accessible	Table includes extra variables needed for AIS/LCK configurable vlans
I32 prvtCfmMaAisLckVlanId	1.3.6.1.4.1.738.1.5.131.1.9.1.1.1	Integer32	not-accessible	Vlan ID (towards customer level) that the generated AIS/LCK packets should use.
ROW prvtCfmMaAisLckVlanRowStatus	1.3.6.1.4.1.738.1.5.131.1.9.1.1.2	RowStatus	read-create	The status of the row.

RFC description

Extends Connectivity Fault Management (CFM) for IEEE 802.1ag on BATM T-Metro switches with proprietary management objects.

Start monitoring BATM carrier Ethernet switches/aggregation nodes with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PRVT-CFM-MIB