PRVT-CES-MIB

All MIBs › PRVT-CES-MIB

Organization: BATM Advanced Communication

Last Updated: 2009-05-18

Category: Circuit Emulation

Description: Manages BATM Advanced Communication Circuit Emulation Service (CES) configuration, jitter buffer, and pseudowire TDM circuit status.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PRVT-CES-MIB?

PRVT-CES-MIB is a BATM Advanced Communications enterprise MIB for Circuit Emulation Service (CES), managing TDM pseudowire circuits carried over a packet network, extending configuration for DS1 modules beyond what the standard DS1-MIB covers. It exposes per-port configuration (E1 impedance, T1 gain limit, line type, long cable length compensation), operational and administrative controls (port shutdown, service clock source), and status/statistics objects including port operational status and clearable port statistics counters. This is a hardware/service status monitoring MIB for TDM circuit emulation - prvtCESPortOperStatus reveals whether a DS1/E1 port carrying emulated TDM traffic is up or down, prvtCESServiceClock shows the clock recovery source (critical for jitter-free TDM playback), and prvtCESUnappTable tracks unassigned/unapplied circuit configuration, together giving visibility into pseudowire circuit health. It explicitly extends and complements the standard DS1-MIB, indicating a direct dependency on that IETF standard for base DS1 interface objects. It's deployed in telecom access/aggregation networks where BATM equipment provides TDM circuit emulation over Ethernet/MPLS packet infrastructure. Engineers can download the PRVT-CES-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in PRVT-CES-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

BATM Advanced Communications circuit emulation (CES) equipment

Monitoring Examples

An admin polls prvtCESDsx1ExtTable/prvtCESDsx1ExtEntry to check prvtCESPortOperStatus for a T1 circuit, and if it is down, checks prvtCESPortLineType and prvtCEST1LongCableLength for a line-configuration mismatch versus the actual cable run. prvtCESServiceClock is checked to confirm the port is using the correct clock source (e.g., recovered vs. internal), since a mismatched clock source causes slips/jitter in the emulated TDM stream. prvtCESClearPortStatistics is invoked after fixing an issue to reset counters for a clean baseline going forward.

What Can Be Monitored

port operational status
service clock source
line type/impedance configuration
port statistics counters

Imported Objects

From DS1-MIB

dsx1ConfigEntry

OBJECT-TYPE

From PRVT-SWITCH-MIB

switch

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION
TimeStamp

OIDs

OID symbolic	OID numeric	Type	Access	Description
prvtCESMib	1.3.6.1.4.1.738.1.5.111			This module includes configuration parameters for DS1 modules not included in DS1-MIB.
prvtCESNotifications	1.3.6.1.4.1.738.1.5.111.0
NTF prvtCESDsx1Alarm	1.3.6.1.4.1.738.1.5.111.0.1			This notification is sent when the value of a TDM port error condition statistic has exceeded the configured threshold.
NTF prvtCESModuleAvailable	1.3.6.1.4.1.738.1.5.111.0.2			prvtCESModuleAvailable trap
NTF prvtCESModuleUnAvailableDueExtract	1.3.6.1.4.1.738.1.5.111.0.3			prvtCESModuleUnAvailableDueExtract trap.
NTF prvtCESModuleUnAvailableDueReload	1.3.6.1.4.1.738.1.5.111.0.4			prvtCESModuleUnAvailableDueReload trap
prvtCESObjects	1.3.6.1.4.1.738.1.5.111.1
prvtCESDsx1ExtTable	1.3.6.1.4.1.738.1.5.111.1.1		not-accessible	This table contains object for configuring DS1 interfaces, not supported in dsx1ConfigTable.
prvtCESDsx1ExtEntry	1.3.6.1.4.1.738.1.5.111.1.1.1		not-accessible	prvtCESDsx1ExtEntry
E1I prvtCESE1Impedance	1.3.6.1.4.1.738.1.5.111.1.1.1.1	E1Impedance	read-write	This object configures temination impedance for TDM ports if the line type is E1.
T1G prvtCEST1GainLimit	1.3.6.1.4.1.738.1.5.111.1.1.1.2	T1GainLimit	read-write	This object configures Tx or Rx gain limit for TDM ports if the line type is T1.
INT prvtCESPortShutdown	1.3.6.1.4.1.738.1.5.111.1.1.1.3	INTEGER	read-write	Shutdown TDM port.
INT prvtCESPortLineType	1.3.6.1.4.1.738.1.5.111.1.1.1.4	INTEGER	read-write	Additional line types. For reference see object dsx1LineType
T1L prvtCEST1LongCableLength	1.3.6.1.4.1.738.1.5.111.1.1.1.5	T1LongCableLength	read-write	Long cable length options for T1 mode.
INT prvtCESPortOperStatus	1.3.6.1.4.1.738.1.5.111.1.1.1.6	INTEGER	read-only	TDM link state.
INT prvtCESClearPortStatistics	1.3.6.1.4.1.738.1.5.111.1.1.1.7	INTEGER	read-write	Clear port statistics.
SER prvtCESServiceClock	1.3.6.1.4.1.738.1.5.111.1.1.1.8	ServiceClock	read-write	Service Clock available only for DS1 interface.
prvtCESModuleConfTable	1.3.6.1.4.1.738.1.5.111.1.2		not-accessible	This table contains object for configuring options that are applied to the entire module.
prvtCESModuleConfEntry	1.3.6.1.4.1.738.1.5.111.1.2.1		not-accessible	prvtCESModuleConfEntry
I32 prvtCESModuleIndex	1.3.6.1.4.1.738.1.5.111.1.2.1.1	Integer32	accessible-for-notify	Index of each CES module installed.
CES prvtCESModuleLineType	1.3.6.1.4.1.738.1.5.111.1.2.1.2	CESLineType	read-write	Line mode for the module.
INT prvtCESModuleTxClock	1.3.6.1.4.1.738.1.5.111.1.2.1.3	INTEGER	read-write	Configures Transmit Source Clock for the module.
INT prvtCESModuleTxBackupClock	1.3.6.1.4.1.738.1.5.111.1.2.1.4	INTEGER	read-write	Configures Backup Clock for the module.
CON prvtCESModuleConfig	1.3.6.1.4.1.738.1.5.111.1.2.1.5	ConfigAction	read-write	When this object is set to applyConfiguration(2), the module is restarted and the changes in dsx1ConfigTable or prvtCESConfTable are applied. The object must be set to rejectConfiguration(3) to remove unapplied changes. If the object is set to restart(4), the module is restarted with applying the changes. This object always returns a value of noop(1) when get.
IP prvtCESModuleIPAddress	1.3.6.1.4.1.738.1.5.111.1.2.1.6	IpAddress	read-write	The CES Module IP address after configuration is applied.
IP prvtCESModuleIPAddressMask	1.3.6.1.4.1.738.1.5.111.1.2.1.7	IpAddress	read-write	The CES Module IP address mask after configuration is applied.
IP prvtCESModuleGateway	1.3.6.1.4.1.738.1.5.111.1.2.1.8	IpAddress	read-write	CES Module Gateway after configuration is applied.
TIM prvtCESModuleUpTime	1.3.6.1.4.1.738.1.5.111.1.2.1.9	TimeStamp	read-only	CES Up Time
OCT prvtCESModuleMACAddress	1.3.6.1.4.1.738.1.5.111.1.2.1.10	OCTET STRING	read-only	CES MAC Address
OCT prvtCESModuleHardwareRevision	1.3.6.1.4.1.738.1.5.111.1.2.1.11	OCTET STRING	read-only	CES Hardware revision
OCT prvtCESModuleFirmwareVersion	1.3.6.1.4.1.738.1.5.111.1.2.1.12	OCTET STRING	read-only	CES Firmware revision
INT prvtCESModuleClearCircuitStatistics	1.3.6.1.4.1.738.1.5.111.1.2.1.13	INTEGER	read-write	Clear circuits statistics.
INT prvtCESModuleLbit	1.3.6.1.4.1.738.1.5.111.1.2.1.14	INTEGER	read-write	Enable/disable L bit set upon AIS defect detection, in structure agnostic mode.
INT prvtCESModulePolicyLops	1.3.6.1.4.1.738.1.5.111.1.2.1.15	INTEGER	read-write	Controls policy lops. Object does not require module to be restarted.
INT prvtCESModulePolicyLbit	1.3.6.1.4.1.738.1.5.111.1.2.1.16	INTEGER	read-write	Controls policy lbit. Object does not require module to be restarted.
INT prvtCESModulePolicyRbit	1.3.6.1.4.1.738.1.5.111.1.2.1.17	INTEGER	read-write	Controls policy rbit. Object does not require module to be restarted.
INT prvtCESModulePolicyRd	1.3.6.1.4.1.738.1.5.111.1.2.1.18	INTEGER	read-write	Controls policy rd. Object does not require module to be restarted.
U32 prvtCESModulePolicyIdlePattern	1.3.6.1.4.1.738.1.5.111.1.2.1.19	Unsigned32	read-write	Controls policy idle pattern. Object does not require module to be restarted.
U32 prvtCESModulePolicyIdleSignalling	1.3.6.1.4.1.738.1.5.111.1.2.1.20	Unsigned32	read-write	Controls policy idle signalling. Object does not require module to be restarted.
I32 prvtCESModulePolicyLopsEnter	1.3.6.1.4.1.738.1.5.111.1.2.1.21	Integer32	read-write	Controls the number of consecutive missed packets required to enter LOPS state. Object does not require module to be restarted.
I32 prvtCESModulePolicyLopsExit	1.3.6.1.4.1.738.1.5.111.1.2.1.22	Integer32	read-write	Controls the number of consecutive missed packets required to exit LOPS state. Object does not require module to be restarted.
INT prvtCESModulePolicyuUnstrLbit	1.3.6.1.4.1.738.1.5.111.1.2.1.23	INTEGER	read-write	If a packet is received with L bit set, and the payload is present (not suppressed), one of the following is sent to the TDM line, according to a globally configurable unstructured L-flag policy: The AIS pattern all-one The received payload as-is none
INT prvtCESModulePolicyuStrReplace	1.3.6.1.4.1.738.1.5.111.1.2.1.24	INTEGER	read-write	If a missing packet is detected, one of the following is sent to the TDM line, according to a globally configurable structured missing packet replacement policy: The AIS pattern all-one on the relevant timeslots The configured IDLE pattern
INT prvtCESModulePolicyuUnstrReplace	1.3.6.1.4.1.738.1.5.111.1.2.1.25	INTEGER	read-write	If a missing packet is detected, one of the following is sent to the TDM line, according to a globally configurable unstructured missing packet replacement policy: The AIS pattern all-one The configured IDLE pattern
INT prvtCESModulePolicyuUnstrLops	1.3.6.1.4.1.738.1.5.111.1.2.1.26	INTEGER	read-write	If a CES circuit enters the LOPS state, one of the following is sent to the TDM line, according to a globally configurable unstructured missing packet replacement policy: The AIS pattern all-one The contents of the jitter buffer - none
SER prvtCESModuleServiceClock	1.3.6.1.4.1.738.1.5.111.1.2.1.27	ServiceClock	read-write	Clock mode for CES module
I32 prvtCESModulePolicyuUnstrReplacePattern	1.3.6.1.4.1.738.1.5.111.1.2.1.28	Integer32	read-write	Unstructured packet replace policy pattern number
prvtCESUnappTable	1.3.6.1.4.1.738.1.5.111.1.3		not-accessible	This table displays CES module configuration which will take effect after prvtCESModuleConf is set to applyConfiguration(2).
prvtCESUnappEntry	1.3.6.1.4.1.738.1.5.111.1.3.1		not-accessible	prvtCESUnappEntry
INT prvtCESUnappLineType	1.3.6.1.4.1.738.1.5.111.1.3.1.1	INTEGER	read-only	The value of dsx1LineType before configuration is applied.
INT prvtCESUnappLineCoding	1.3.6.1.4.1.738.1.5.111.1.3.1.2	INTEGER	read-only	The value of dsx1LineCoding before configuration is applied.
INT prvtCESUnappLoopbackConfig	1.3.6.1.4.1.738.1.5.111.1.3.1.3	INTEGER	read-only	The value of dsx1LoopbackConfig before configuration is applied.
INT prvtCESUnappSignalMode	1.3.6.1.4.1.738.1.5.111.1.3.1.4	INTEGER	read-only	The value of dsx1SignalMode before configuration is applied.
INT prvtCESUnappTransmitClockSource	1.3.6.1.4.1.738.1.5.111.1.3.1.5	INTEGER	read-only	The value of dsx1TransmitClockSource before configuration is applied.
INT prvtCESUnappTransmitClockBackup	1.3.6.1.4.1.738.1.5.111.1.3.1.6	INTEGER	read-only	The value of dsx1TransmitClockBackup before configuration is applied.
I32 prvtCESUnappLineLength	1.3.6.1.4.1.738.1.5.111.1.3.1.7	Integer32	read-only	The value of dsx1LineLength before configuration is applied.
INT prvtCESUnappLineMode	1.3.6.1.4.1.738.1.5.111.1.3.1.8	INTEGER	read-only	The value of dsx1LineMode before configuration is applied.
INT prvtCESUnappLineBuildOut	1.3.6.1.4.1.738.1.5.111.1.3.1.9	INTEGER	read-only	The value of dsx1LineBuildOut before configuration is applied.
E1I prvtCESUnappE1Impedance	1.3.6.1.4.1.738.1.5.111.1.3.1.10	E1Impedance	read-only	The value of prvtCESE1Impedance before configuration is applied.
T1G prvtCESUnappT1GainLimit	1.3.6.1.4.1.738.1.5.111.1.3.1.11	T1GainLimit	read-only	The value of prvtCEST1GainLimit before configuration is applied.
IP prvtCESUnappIPAddress	1.3.6.1.4.1.738.1.5.111.1.3.1.12	IpAddress	read-only	The CES Module IP address before configuration is applied.
IP prvtCESUnappIPAddressMask	1.3.6.1.4.1.738.1.5.111.1.3.1.13	IpAddress	read-only	The CES Module IP address mask before configuration is applied.
IP prvtCESUnappGateway	1.3.6.1.4.1.738.1.5.111.1.3.1.14	IpAddress	read-only	The CES Module Gateway before configuration is applied.
prvtCESDsx1AlarmTable	1.3.6.1.4.1.738.1.5.111.1.4		not-accessible	This table contains object for configuring and displaying TDM ports TCA thresholds.
prvtCESDsx1AlarmEntry	1.3.6.1.4.1.738.1.5.111.1.4.1		not-accessible	prvtCESDsx1AlarmEntry
I32 prvtCESDsx1AlarmPort	1.3.6.1.4.1.738.1.5.111.1.4.1.1	Integer32	not-accessible	The DS1 port for which this alarm is configured.
G32 prvtCESDsx1AlarmIndex	1.3.6.1.4.1.738.1.5.111.1.4.1.2	Gauge32	not-accessible	An integer uniquely identifying an alarm entry.
OID prvtCESDsx1AlarmVariable	1.3.6.1.4.1.738.1.5.111.1.4.1.3	OBJECT IDENTIFIER	read-only	The OID of the variable whose value is being monitored. Depending on the time interval, the error condition and the ifIndex of the TDM interface, this points to an object from an entry in dsx1CurrentTable or dsx1TotalTable.
I32 prvtCESDsx1AlarmThreshold	1.3.6.1.4.1.738.1.5.111.1.4.1.4	Integer32	read-write	The alarm condition threshold for this alarm entry. The alarm is triggered if the value of the object pointed by prvtCESDsx1AlarmVariable remains above this threshold for more than 3 seconds.
I32 prvtCESDsx1AlarmValue	1.3.6.1.4.1.738.1.5.111.1.4.1.5	Integer32	accessible-for-notify	The value of the object pointed to by prvtCESDsx1AlarmVariable, present for notification purposes.
INT prvtCESAlarmMonitor	1.3.6.1.4.1.738.1.5.111.1.5	INTEGER	read-write	CES alarm monitor
prvtCESCICTable	1.3.6.1.4.1.738.1.5.111.1.6		not-accessible	This table contains objects for configuring Clock Input Controller.
prvtCESCICEntry	1.3.6.1.4.1.738.1.5.111.1.6.1		not-accessible	prvtCESCICEntry
I32 prvtCESCICModuleId	1.3.6.1.4.1.738.1.5.111.1.6.1.1	Integer32	not-accessible	Slot of CES module installed.
G32 prvtCESCICNumber	1.3.6.1.4.1.738.1.5.111.1.6.1.2	Gauge32	not-accessible	An integer uniquely identifying a Clock Input Controller.
I32 prvtCESCICClockNumber	1.3.6.1.4.1.738.1.5.111.1.6.1.3	Integer32	read-only	This variable indicates the index of the clock the clock input controller belongs to
INT prvtCESCICMode	1.3.6.1.4.1.738.1.5.111.1.6.1.4	INTEGER	read-only	The mode of the clock input controller. Not all clock input controllers support all modes. The clock input controller status is 'locked' only if the clock input controller is in 'normal' mode.
I32 prvtCESCICTdmPort	1.3.6.1.4.1.738.1.5.111.1.6.1.5	Integer32	read-write	If the clock input controller recovers a clock from a port , this variable indicates the TDM Port. Otherwise, it must be set to zero.
I32 prvtCESCICCircuit	1.3.6.1.4.1.738.1.5.111.1.6.1.6	Integer32	read-write	If the clock input controller recovers a clock from a circuit, this variable indicates the circuit ID. Otherwise, it must be set to zero.
INT prvtCESCICStatus	1.3.6.1.4.1.738.1.5.111.1.6.1.7	INTEGER	read-only	The status of the input reference.Reference is ok when the status is 'locked'. Otherwise, the status is 'notLocked'. Alternatively, if an error was detected at the input, the status indicates this error.
INT prvtCESCICState	1.3.6.1.4.1.738.1.5.111.1.6.1.8	INTEGER	read-only	The state is set to 'active' if the input controller was selected by the clock to drive the clock output. At least one input out of the clock-input-controllers attached to a clock must be in an 'active' state at any given time
prvtCESCICMappTable	1.3.6.1.4.1.738.1.5.111.1.7		not-accessible	This table contains clock configuration and status monitoring information.
prvtCESCICMappEntry	1.3.6.1.4.1.738.1.5.111.1.7.1		not-accessible	prvtCESCICMappEntry
I32 prvtCESCICMappModuleId	1.3.6.1.4.1.738.1.5.111.1.7.1.1	Integer32	read-only	Slot of CES module installed.
G32 prvtCESCICMappClockNumber	1.3.6.1.4.1.738.1.5.111.1.7.1.2	Gauge32	read-only	Index for the conceptual row identifying a clock within this mapping table
G32 prvtCESCICMappCICNumber	1.3.6.1.4.1.738.1.5.111.1.7.1.3	Gauge32	read-only	Index for the conceptual row identifying a clock input within this mapping table
INT prvtCESCICMappState	1.3.6.1.4.1.738.1.5.111.1.7.1.4	INTEGER	read-only	The state is set to 'active' if the input controller was selected by the clock to drive the clock output. At least one input out of the clock-input-controllers attached to a clock must be in an 'active' state at any given time This value of this variable is equal to the prvtCESCICState variable in the CIC table
prvtCESApsTable	1.3.6.1.4.1.738.1.5.111.1.8		not-accessible	This table contains objects needed APS configuration
prvtCESApsEntry	1.3.6.1.4.1.738.1.5.111.1.8.1		not-accessible	prvtCESApsEntry
I32 prvtCESApsModuleId	1.3.6.1.4.1.738.1.5.111.1.8.1.1	Integer32	not-accessible	An integer uniquely identifying slot of the CES module installed
INT prvtCESApsEnable	1.3.6.1.4.1.738.1.5.111.1.8.1.2	INTEGER	read-write	Enable/Disable Automatic Protection Switching
I32 prvtCESApsActiveLine	1.3.6.1.4.1.738.1.5.111.1.8.1.3	Integer32	read-write	APS active line
I32 prvtSdBerThreshold	1.3.6.1.4.1.738.1.5.111.1.8.1.4	Integer32	read-write	The Signal Degrade Bit Error Rate. The negated value of this number is used as the exponent of 10 for computing the threshold value for the Bit Error Rate (BER). For example, a value of 5 indicates a BER threshold of 10^-5.
I32 prvtSfBerThreshold	1.3.6.1.4.1.738.1.5.111.1.8.1.5	Integer32	read-write	The Signal Failure Bit Error Rate. The negated value of this number is used as the exponent of 10 for computing the threshold value for the Bit Error Rate (BER). For example, a value of 5 indicates a BER threshold of 10^-5.
prvtCESUpdateFirmwareTable	1.3.6.1.4.1.738.1.5.111.1.9		not-accessible	This table contains object needed in update firmware of CES module
prvtCESUpdateFirmwareEntry	1.3.6.1.4.1.738.1.5.111.1.9.1		not-accessible	prvtCESUpdateFirmwareEntry
I32 prvtCESModuleId	1.3.6.1.4.1.738.1.5.111.1.9.1.1	Integer32	not-accessible	An integer uniquely identifying slot of the CES module installed
OCT prvtCESFirmwareImageName	1.3.6.1.4.1.738.1.5.111.1.9.1.2	OCTET STRING	read-write	Name of the firmware image file
INT prvtCESUpdateAction	1.3.6.1.4.1.738.1.5.111.1.9.1.3	INTEGER	read-write	Update CES firmware
INT prvtCESUpdateStatus	1.3.6.1.4.1.738.1.5.111.1.9.1.4	INTEGER	read-only	The status of the last update procedure, if any. This object will have a value of updateStatusUnknown(2) if no update process has been performed.
IP prvtCESTFTPServer	1.3.6.1.4.1.738.1.5.111.1.9.1.5	IpAddress	read-write	IP Address of Tftp Server
prvtCESConformance	1.3.6.1.4.1.738.1.5.111.2
prvtCESDsx1Compliances	1.3.6.1.4.1.738.1.5.111.2.1
prvtCESDsx1Compliance	1.3.6.1.4.1.738.1.5.111.2.1.1			The compliance statement for management of TDM ports.
prvtCESDsx1Groups	1.3.6.1.4.1.738.1.5.111.2.2
prvtCESDsx1NotificationsGroup	1.3.6.1.4.1.738.1.5.111.2.2.1			The group of supported notifications.
prvtCESDsx1ROGroup	1.3.6.1.4.1.738.1.5.111.2.2.2			The group of objects with MAX-ACCESS read-write supported with read-only access for the first release.

RFC description

Provides DS1/circuit emulation configuration parameters for BATM/Telco Systems Ethernet switches, including OC3 alarm and APS management.

Start monitoring BATM Advanced Communications circuit emulation (CES) equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PRVT-CES-MIB

What Is PRVT-CES-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description