PDN-TRAPMGR-MIB

All MIBs › PDN-TRAPMGR-MIB

Category: Network Management

Description: Manages SNMP trap destination configuration, throttle rates, and trap enable/disable settings on Paradyne xDSL access devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PDN-TRAPMGR-MIB?

PDN-TRAPMGR-MIB is a Paradyne enterprise MIB for xDSL access devices (such as GranDSLAM/Hotwire-style DSL access multiplexers), managing SNMP trap destination configuration. It defines a trap manager table listing destination IP addresses, subnet masks, and circuit/sub-circuit identifiers, along with counts of registered trap receivers. It is not itself a hardware sensor MIB, but it underlies fault/status monitoring infrastructure: the current-versus-maximum trap manager count reflects the device's notification capacity, and correct destination configuration determines whether hardware/software fault traps (link down, power issues, etc.) actually reach an NMS. It works alongside the standard SNMPv1/v2 trap mechanism and other Paradyne enterprise MIBs that generate the traps it routes. It would be deployed on Paradyne/Zhone xDSL access equipment in telco central offices or points of presence, where the PDN-TRAPMGR-MIB MIB governs whether fault traps actually reach the NMS.

IPNetwork Monitor allows you to monitor SNMP objects defined in PDN-TRAPMGR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Paradyne xDSL access device
DSL access multiplexer (DSLAM)

Monitoring Examples

An admin polls devTrapMgrTable and pdnDevTrapMgrTable entries such as devTrapMgrIpAddress, pdnDevTrapMgrDestAddress, and pdnDevTrapMgrSubnetMask to verify which NMS stations are registered as trap destinations. Comparing devTrapMgrCurrentNumber against devTrapMgrMaxNumber shows whether the trap manager table is near capacity, which would cause new trap destinations to fail to register. This lets an operator confirm fault notifications are reaching all intended monitoring stations.

What Can Be Monitored

configured trap destination addresses
trap destination subnet masks
circuit/sub-circuit identifiers
current vs. max trap manager entries

Imported Objects

From PDN-HEADER-MIB

pdn-traps

From PDN-TC

SwitchState

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

From SNMPv2-TC

DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT devTrapMgrMaxNumber	1.3.6.1.4.1.1795.2.24.2.9.1	INTEGER	read-only	Maximum number of managers allowed in the devTrapMgrTable. This may vary per device.
INT devTrapMgrCurrentNumber	1.3.6.1.4.1.1795.2.24.2.9.2	INTEGER	read-only	Current number of managers in devTrapMgrTable.
devTrapMgrTable	1.3.6.1.4.1.1795.2.24.2.9.3		not-accessible	The trap manager table.
devTrapMgrEntry	1.3.6.1.4.1.1795.2.24.2.9.3.1		not-accessible	An entry in the trap manager table.
IP devTrapMgrIpAddress	1.3.6.1.4.1.1795.2.24.2.9.3.1.1	IpAddress	read-write	Unique IP address identifying a Trap Manager. An existing Trap Manager may be deleted by setting the devTrapMgrIpAddress object to 0.0.0.0 or by setting the devTrapMgrIpAddress object to a new address. A new Trap Manager may be added by setting the devTrapMgrIpAddress object of 0.0.0.0 to the new address as long as there is still room for another Trap Manager.
INT devTrapMgrDestination	1.3.6.1.4.1.1795.2.24.2.9.3.1.2	INTEGER	read-write	The ifIndex to be used with the associated IpAddress when sending traps.
INT devTrapMgrCircuit	1.3.6.1.4.1.1795.2.24.2.9.3.1.3	INTEGER	read-write	The circuit used for management when multiple circuits are allowed over the specified interface (ifIndex). If the interface allows only one circuit, devTrapMgrCircuit is set to 0.
INT devTrapMgrSubCircuit	1.3.6.1.4.1.1795.2.24.2.9.3.1.4	INTEGER	read-write	The subcircuit used for management when devTrapMgrCircuit can be further subdivided.
pdnDevTrapMgrTable	1.3.6.1.4.1.1795.2.24.2.9.4		not-accessible	The paradyne's device trap manager table.
pdnDevTrapMgrEntry	1.3.6.1.4.1.1795.2.24.2.9.4.1		not-accessible	An entry of a trap manager configuration.
IP pdnDevTrapMgrDestAddress	1.3.6.1.4.1.1795.2.24.2.9.4.1.1	IpAddress	read-only	The IP Address of the destination to which a trap must be sent.
IP pdnDevTrapMgrSubnetMask	1.3.6.1.4.1.1795.2.24.2.9.4.1.2	IpAddress	read-only	This object is used to specify the subnet mask
INT pdnDevTrapMgrDestPort	1.3.6.1.4.1.1795.2.24.2.9.4.1.3	INTEGER	read-write	The Port destination used to send the trap.
STR pdnDevTrapMgrCommunityName	1.3.6.1.4.1.1795.2.24.2.9.4.1.4	DisplayString	read-write	This object corresponds to the name of the SNMP Community that will be used when sending the trap out to this manager destination.
INT pdnDevTrapMgrEnable	1.3.6.1.4.1.1795.2.24.2.9.4.1.5	INTEGER	read-write	This object corresponds to turning traps on/off for a particular destination. enable (1) - traps will be sent to the specified destination. disable (2)- traps will not be sent to the specified destination.
ROW pdnDevTrapMgrRowStatus	1.3.6.1.4.1.1795.2.24.2.9.4.1.6	RowStatus	read-write	This object is used to add/delete rows to/from the table.
SWI pdnDevConfigTrapsEnable	1.3.6.1.4.1.1795.2.24.2.9.5	SwitchState	read-write	This objects allows NMS to turn off/on the generation of Traps in the device.

RFC description

Provides trap manager table editing capabilities for Paradyne devices to manage SNMP trap destinations.

Start monitoring Paradyne xDSL access device, DSL access multiplexer (trap destination configuration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PDN-TRAPMGR-MIB

What Is PDN-TRAPMGR-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description