Nortel-MsCarrier-MscPassport-FrameRelayNniMIB

All MIBs › Nortel-MsCarrier-MscPassport-FrameRelayNniMIB

Category: Frame Relay, Nortel MsCarrier MscPassport

Description: Provides SNMP objects for Frame Relay NNI (Network-to-Network Interface) on Nortel MsCarrier MscPassport switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-MsCarrier-MscPassport-FrameRelayNniMIB?

This Nortel MsCarrier MscPassport MIB provides SNMP objects for Frame Relay Network-to-Network Interface (NNI) links, which interconnect Frame Relay switches/networks (as opposed to user-facing UNI links) on the Passport platform. It exposes provisioning tables including customer identifier (CID) data for tracking which customer/service a given NNI link serves, plus a state table for the operational status of NNI components. Monitoring centers on confirming NNI link components are provisioned and active, and on tracking their operational state as a proxy for inter-network link health, since the sampled objects do not include throughput or error counters. It relies on the Frame Relay Forum's NNI signaling specification and shares the common Passport row-status/component provisioning model with sibling Frame Relay MIBs in this family. It is used by carriers interconnecting Frame Relay networks or switches via NNI trunks on Nortel MsCarrier Passport equipment. Network engineers evaluating or troubleshooting this functionality can download the Nortel-MsCarrier-MscPassport-FrameRelayNniMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-MsCarrier-MscPassport-FrameRelayNniMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel MsCarrier MscPassport switch

Monitoring Examples

An operator would poll mscFrNniRowStatusTable/mscFrNniRowStatusEntry to verify an NNI link component is active, then check mscFrNniStateTable/mscFrNniStateEntry for its operational status and mscFrNniCidDataTable for the mscFrNniCustomerIdentifier tied to that link. If inter-carrier Frame Relay traffic stops flowing, the first checks are whether the NNI component's row status and operational state both indicate "up," and whether the customer identifier binding (mscFrNniDna) still matches provisioning records. No traffic counters are exposed, so this is primarily a provisioning/state health check.

What Can Be Monitored

NNI link row status
NNI operational state
customer identifier binding
NNI DNA/addressing data

Imported Objects

From Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
InterfaceIndex
RowPointer
RowStatus
StorageType
Unsigned32

From Nortel-MsCarrier-MscPassport-TextualConventionsMIB

AsciiString
DigitString
EnterpriseDateAndTime
FixedPoint3
Hex
HexString
Link
NonReplicated
PassportCounter64
Unsigned64

From Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB

mscComponents	OBJECT-IDENTITY
mscPassportMIBs	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
mscFrNni	1.3.6.1.4.1.562.36.2.1.70
mscFrNniRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.1		not-accessible	This entry controls the addition and deletion of mscFrNni components.
mscFrNniRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.1.1		not-accessible	A single entry in the table represents a single mscFrNni component.
ROW mscFrNniRowStatus	1.3.6.1.4.1.562.36.2.1.70.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNni components. These components can be added and deleted.
STR mscFrNniComponentName	1.3.6.1.4.1.562.36.2.1.70.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniStorageType	1.3.6.1.4.1.562.36.2.1.70.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNni tables.
I32 mscFrNniIndex	1.3.6.1.4.1.562.36.2.1.70.1.1.10	Integer32	not-accessible	This variable represents the index for the mscFrNni tables.
mscFrNniDna	1.3.6.1.4.1.562.36.2.1.70.2
mscFrNniDnaRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.2.1		not-accessible	This entry controls the addition and deletion of mscFrNniDna components.
mscFrNniDnaRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.2.1.1		not-accessible	A single entry in the table represents a single mscFrNniDna component.
ROW mscFrNniDnaRowStatus	1.3.6.1.4.1.562.36.2.1.70.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniDna components. These components cannot be added nor deleted.
STR mscFrNniDnaComponentName	1.3.6.1.4.1.562.36.2.1.70.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDnaStorageType	1.3.6.1.4.1.562.36.2.1.70.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDna tables.
NON mscFrNniDnaIndex	1.3.6.1.4.1.562.36.2.1.70.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDna tables.
mscFrNniDnaCug	1.3.6.1.4.1.562.36.2.1.70.2.2
mscFrNniDnaCugRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.2.2.1		not-accessible	This entry controls the addition and deletion of mscFrNniDnaCug components.
mscFrNniDnaCugRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.2.2.1.1		not-accessible	A single entry in the table represents a single mscFrNniDnaCug component.
ROW mscFrNniDnaCugRowStatus	1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniDnaCug components. These components can be added and deleted.
STR mscFrNniDnaCugComponentName	1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDnaCugStorageType	1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDnaCug tables.
I32 mscFrNniDnaCugIndex	1.3.6.1.4.1.562.36.2.1.70.2.2.1.1.10	Integer32	not-accessible	This variable represents the index for the mscFrNniDnaCug tables.
mscFrNniDnaCugCugOptionsTable	1.3.6.1.4.1.562.36.2.1.70.2.2.10		not-accessible	Attributes in this group define ClosedUserGroup options associated with interlockCode. DNA's with the same CUG (interlockCode) can make calls within this group. Various combinations which permit or prevent calls in the same CUG group are defined here.
mscFrNniDnaCugCugOptionsEntry	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1		not-accessible	An entry in the mscFrNniDnaCugCugOptionsTable.
INT mscFrNniDnaCugType	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.1	INTEGER	read-write	This attribute specifies the CUG type - the CUG is either a national CUG, or an international CUG. International closed user groups are usually established between DTEs for which there is an X.75 Gateway between; whereas national closed user groups are usually established between DTEs for which there is no X.75 Gateway between. (National CUGs cannot normally traverse an X.75 Gateway). If this attribute is set to national, then the CUG is a national CUG, in which case, the dnic should be left at its default value since it is not part of a national CUG. If this attribute is set to international, then the CUG is an international CUG, in which case, the dnic should be set appropriately as part of the CUG interlockCode.
STR mscFrNniDnaCugDnic	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.2	DigitString	read-write	This attribute specifies the dnic (Data Network ID Code) of the CUG by which packet networks are identified. This attribute is not applicable if the CUG is a national CUG, as specified by the CUG type attribute. There are usually 1 or 2 dnics assigned per country, for public networks. The U.S. is an exception where each BOC has a dnic. Also, a group of private networks can have its own dnic. dnic value is not an arbitrary number. It is assigned by international agreement and controlled by CCITT.
U32 mscFrNniDnaCugInterlockCode	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.3	Unsigned32	read-write	This attribute specifies the CUG identifier of a national or international CUG call. It is an arbitrary number and it also can be called CUG in some descriptions. Interfaces (DNA's) defined with this number can make calls to DNA's with the same interlockCode.
INT mscFrNniDnaCugPreferential	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.4	INTEGER	read-write	The attribute 'preferential', if set to yes indicates that this CUG is the SIMPLE CUG (as defined in ITU X.36 [10/96]), in which case it will be used during the call establishment phase if the DTE has not explicitly specified a CUG index in the call request packet. If set to no, then this CUG is not the SIMPLE CUG, but an instance of the SELECTABLE CUG. The attribute 'preferential' is set to no by CAS when a CUG instance is created. If only one CUG instance exists under a DNA, and if this CUG's attributes 'incCalls' and 'outCall' are both set to allowed, then this CUG instance can be changed to a SIMPLE CUG by setting the attribute 'preferential' to yes. If more than one CUG instances exist under a DNA, none of the CUGs can be set by the user as 'preferential'. Essentially, the attribute 'preferential' distinguishes a SIMPLE CUG from a SELECTABLE CUG. In the case of a FRUNI DNA with a single CUG instance, the CUG can be a SIMPLE CUG (preferential = yes) or the only instance of a SELECTABLE CUG (preferential = no).
INT mscFrNniDnaCugOutCalls	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.5	INTEGER	read-write	This attribute, if set to allowed indicates that outgoing calls (from the DTE into the network) can be made using this particular CUG. If set to a value of disallowed, then outgoing calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Outgoing Calls Barred' feature for CUGs in that outgoing calls are barred if this attribute is set to a value of disallowed.
INT mscFrNniDnaCugIncCalls	1.3.6.1.4.1.562.36.2.1.70.2.2.10.1.6	INTEGER	read-write	This attribute, if set to allowed indicates that incoming calls (from the network to the DTE) can be made using this particular CUG. If set to disallowed, then incoming calls cannot be made using this CUG - such calls will be cleared by the local DCE. This attribute corresponds to the CCITT 'Incoming Calls Barred' feature for CUGs in that incoming calls are barred if this attribute is set to a value of disallowed.
mscFrNniDnaHgM	1.3.6.1.4.1.562.36.2.1.70.2.3
mscFrNniDnaHgMRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.2.3.1		not-accessible	This entry controls the addition and deletion of mscFrNniDnaHgM components.
mscFrNniDnaHgMRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.2.3.1.1		not-accessible	A single entry in the table represents a single mscFrNniDnaHgM component.
ROW mscFrNniDnaHgMRowStatus	1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniDnaHgM components. These components can be added and deleted.
STR mscFrNniDnaHgMComponentName	1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDnaHgMStorageType	1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDnaHgM tables.
NON mscFrNniDnaHgMIndex	1.3.6.1.4.1.562.36.2.1.70.2.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDnaHgM tables.
mscFrNniDnaHgMHgAddr	1.3.6.1.4.1.562.36.2.1.70.2.3.2
mscFrNniDnaHgMHgAddrRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.2.3.2.1		not-accessible	This entry controls the addition and deletion of mscFrNniDnaHgMHgAddr components.
mscFrNniDnaHgMHgAddrRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1		not-accessible	A single entry in the table represents a single mscFrNniDnaHgMHgAddr component.
ROW mscFrNniDnaHgMHgAddrRowStatus	1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniDnaHgMHgAddr components. These components can be added and deleted.
STR mscFrNniDnaHgMHgAddrComponentName	1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDnaHgMHgAddrStorageType	1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDnaHgMHgAddr tables.
I32 mscFrNniDnaHgMHgAddrIndex	1.3.6.1.4.1.562.36.2.1.70.2.3.2.1.1.10	Integer32	not-accessible	This variable represents the index for the mscFrNniDnaHgMHgAddr tables.
mscFrNniDnaHgMHgAddrAddrTable	1.3.6.1.4.1.562.36.2.1.70.2.3.2.10		not-accessible	This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
mscFrNniDnaHgMHgAddrAddrEntry	1.3.6.1.4.1.562.36.2.1.70.2.3.2.10.1		not-accessible	An entry in the mscFrNniDnaHgMHgAddrAddrTable.
INT mscFrNniDnaHgMHgAddrNumberingPlanIndicator	1.3.6.1.4.1.562.36.2.1.70.2.3.2.10.1.1	INTEGER	read-write	This attribute indicates the Numbering Plan Indicator (NPI) of the DNA. The address may belong to X.121 or E.164 plans.
STR mscFrNniDnaHgMHgAddrDataNetworkAddress	1.3.6.1.4.1.562.36.2.1.70.2.3.2.10.1.2	DigitString	read-write	This attribute contains digits which form the unique identifier of the customer interface. It can be compared (approximation only) to a telephone number where the phone number identifies a unique telephone set. DNA digits are selected and assigned by network operators.
mscFrNniDnaHgMIfTable	1.3.6.1.4.1.562.36.2.1.70.2.3.10		not-accessible	This group contains the interface parameters between the HuntGroupMember and the hunt group server.
mscFrNniDnaHgMIfEntry	1.3.6.1.4.1.562.36.2.1.70.2.3.10.1		not-accessible	An entry in the mscFrNniDnaHgMIfTable.
U32 mscFrNniDnaHgMAvailabilityUpdateThreshold	1.3.6.1.4.1.562.36.2.1.70.2.3.10.1.1	Unsigned32	read-write	This attribute specifies how much availableAggregateCIR can change before an Availability Message Packet (AMP) is sent to the hunt group server informing it of the change. If the value specified is not a multiple of 2048, the value actually used as the threshold will be the next higher multiple of 2048.
mscFrNniDnaHgMOpTable	1.3.6.1.4.1.562.36.2.1.70.2.3.11		not-accessible	This group contains the operational attributes of the HuntGroupMember component.
mscFrNniDnaHgMOpEntry	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1		not-accessible	An entry in the mscFrNniDnaHgMOpTable.
U32 mscFrNniDnaHgMMaximumAvailableAggregateCir	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.1	Unsigned32	read-only	This attribute indicates the maximum available bandwidth for this hunt group member. This value represents the total sum of the sixteen egress bandwidth pools. It is the sum of the sixteen indices of the FrNni Ca egressBandwidthPool attribute multiplied by the link speed.
U32 mscFrNniDnaHgMAvailableAggregateCir	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.2	Unsigned32	read-only	This attribute indicates the current total available bandwidth reported to the hunt group server in the Availability Message Packet (AMP). This value represents the sum of the sixteen currently available egress bandwidth pools. It is the sum of the sixteen indices of the FrNni Ca egressPoolAvailableBandwidth attribute. It increments when a connection is released. It decrements when a connection is accepted. Both this attribute and the availableDlcis attribute must be non zero for this interface to receive calls on a hunt group.
INT mscFrNniDnaHgMAvailabilityDelta	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.3	INTEGER	read-only	This attribute indicates the net change in the available aggregate CIR since the last Availability Message Packet (AMP) was sent to the Hunt Group. Once the absolute value of this attribute reaches the availabilityUpdateThreshold an AMP is sent to the hunt group server(s) and the availabilityDelta is re-computed.
U32 mscFrNniDnaHgMAvailableDlcis	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.5	Unsigned32	read-only	This attribute indicates the number of DLCIs available for SVCs on the interface associated with this DNA. If this value reaches 0, an AMP with zero availability is sent to the hunt group server(s). Both this attribute and the availableAggregateCir attribute must be non zero for this DNA to receive calls on the hunt group.
UNS mscFrNniDnaHgMMaximumAvailableAggregateCir64	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.6	Unsigned64	read-only	This attribute indicates the maximum available bandwidth for this hunt group member. This value represents the total sum of the sixteen egress bandwidth pools. It is the sum of the sixteen indices of the FrNni Ca egressBandwidthPool attribute multiplied by the link speed.
UNS mscFrNniDnaHgMAvailableAggregateCir64	1.3.6.1.4.1.562.36.2.1.70.2.3.11.1.7	Unsigned64	read-only	This attribute indicates the current total available bandwidth reported to the hunt group server in the Availability Message Packet (AMP). This value represents the sum of the sixteen currently available egress bandwidth pools. It is the sum of the sixteen indices of the FrNni Ca egressPoolAvailableBandwidth attribute. It increments when a connection is released. It decrements when a connection is accepted. Both this attribute and the availableDlcis attribute must be non zero for this interface to receive calls on a hunt group.
mscFrNniDnaAddressTable	1.3.6.1.4.1.562.36.2.1.70.2.10		not-accessible	This group contains attributes common to all DNAs. Every DNA used in the network is defined with this group of 2 attributes.
mscFrNniDnaAddressEntry	1.3.6.1.4.1.562.36.2.1.70.2.10.1		not-accessible	An entry in the mscFrNniDnaAddressTable.
INT mscFrNniDnaNumberingPlanIndicator	1.3.6.1.4.1.562.36.2.1.70.2.10.1.1	INTEGER	read-write	This attribute indicates the Numbering Plan Indicator (NPI) of the DNA that is entered. Address may belong to X.121 or E.164 plans. X.121 is used in packet switched data networks.
STR mscFrNniDnaDataNetworkAddress	1.3.6.1.4.1.562.36.2.1.70.2.10.1.2	DigitString	read-write	This attribute indicates the customer's unique identifier. It is the equivalent of the telephone number in the telephone network.
mscFrNniDnaOutgoingOptionsTable	1.3.6.1.4.1.562.36.2.1.70.2.11		not-accessible	This group defines DNA call options for calls made from the interface. These options are not used for calls arriving to the interface represented by this DNA.
mscFrNniDnaOutgoingOptionsEntry	1.3.6.1.4.1.562.36.2.1.70.2.11.1		not-accessible	An entry in the mscFrNniDnaOutgoingOptionsTable.
INT mscFrNniDnaOutDefaultPriority	1.3.6.1.4.1.562.36.2.1.70.2.11.1.7	INTEGER	read-write	This attribute indicates the default priority of outgoing calls from the DTE to the network. It can be overridden by the discardPriority under DLCI Direct Call subcomponent. This option can be also included in X.25 signalling, in such case it will be overruled.
INT mscFrNniDnaOutDefaultPathSensitivity	1.3.6.1.4.1.562.36.2.1.70.2.11.1.11	INTEGER	read-write	This attribute specifies the default class of path sensitivity to network for all outgoing calls that use this DNA. The chosen default class of path sensitivity applies to all outgoing calls established using this DNA. This attribute, if set to throughput, indicates that the default class is throughput sensitive. If set to delay, then the default class is delay sensitive. The default of outDefaultPathSensitivity is throughput.
INT mscFrNniDnaOutPathSensitivityOverRide	1.3.6.1.4.1.562.36.2.1.70.2.11.1.12	INTEGER	read-write	If this attribute is set to yes in the call request, the called end will use the calling end provisioning data on path sensitivity to override its own provisioning data. The default of outPathSensitivityOverRide is yes.
INT mscFrNniDnaOutDefaultPathReliability	1.3.6.1.4.1.562.36.2.1.70.2.11.1.14	INTEGER	read-write	This attribute specifies the default class of routing for reliability routing for all outgoing calls (from the DTE to the network) using this particular DNA. The chosen default class of routing applies to all outgoing calls established using this DNA, and applies to the packets travelling in both directions on all outgoing calls (local to remote, and remote to local). For incoming calls, the default class of routing is chosen by the calling party (as opposed to DPN, where either end of the call can choose the default routing class). This attribute, if set to a value of normal, indicates that the default class of routing is normal reliability routing. If set to a value of high, then the default class of routing is high reliability routing. High reliability is the standard choice for most DPN and Passport services. It usually indicates that packets are overflowed or retransmitted at various routing levels. Typically high reliability results in duplication and disordering of packets in the network when errors are detected or during link congestion. However, the VC handles the duplication and disordering to ensure that packets are delivered to the DTE properly. For the Frame Relay service, duplication of packets is not desired, in which case, normal reliability may be chosen as the preferred class of routing.
INT mscFrNniDnaOutAccess	1.3.6.1.4.1.562.36.2.1.70.2.11.1.17	INTEGER	read-write	This attribute is an extension of the Closed User Group (CUG) facility, as follows: This attribute, if set to a value of allowed indicates that outgoing calls (from the DTE to the network) to the open (non-CUG) part of the network are permitted. It also permits outgoing calls to DTEs that have Incoming Access capabilities. If set to a value of disallowed, then such calls cannot be made using this DNA. Such calls will be cleared by the local DCE. This attribute corresponds to the ITU-T 'Closed User Group with Outgoing Access' feature for DNAs in that outgoing access is granted if this attribute is set to a value of allowed.
INT mscFrNniDnaDefaultTransferPriority	1.3.6.1.4.1.562.36.2.1.70.2.11.1.18	INTEGER	read-write	This attribute specifies the default transfer priority for all outgoing calls using this particular DNA. It can be overridden by the transferPriority provisioned in the Dlci DirectCall sub-component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n indicates the transfer priority index, contains a default setting for routing class of service (multimedia, delay or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required. The default defaultTransferPriority is 0.
INT mscFrNniDnaTransferPriorityOverRide	1.3.6.1.4.1.562.36.2.1.70.2.11.1.19	INTEGER	read-write	When this attribute is set to yes in the call request, the called end will use the calling end provisioning data on transfer priority to override its own provisioning data. If it is set no, the called end will use its own provisioning data on transfer priority. This attribute is not applicable for Frame Relay SVCs. For more information about transfer priority, please refer to the previous attribute defaultTransferPriority. The default of transferPriorityOverRide is yes.
mscFrNniDnaIncomingOptionsTable	1.3.6.1.4.1.562.36.2.1.70.2.12		not-accessible	This group defines options for incoming calls. These options are used for calls arriving to the interface represented by this DNA. For calls originated from the interface, IncomingOptions attributes are not used.
mscFrNniDnaIncomingOptionsEntry	1.3.6.1.4.1.562.36.2.1.70.2.12.1		not-accessible	An entry in the mscFrNniDnaIncomingOptionsTable.
INT mscFrNniDnaIncAccess	1.3.6.1.4.1.562.36.2.1.70.2.12.1.9	INTEGER	read-write	This attribute, if set to a value of allowed specifies that incoming calls (from the network to the DTE) from the open (non-CUG) part of the network are permitted. It also permits incoming calls from DTEs that have outgoing access capabilities. If set to a value of disallowed, such calls cannot be made to this DNA. They will be cleared by the local DCE. This attribute corresponds to the CCITT 'Closed User Group with Incoming Access' feature for DNAs in that incoming access is granted if this attribute is set to a value of allowed.
mscFrNniDnaCallOptionsTable	1.3.6.1.4.1.562.36.2.1.70.2.13		not-accessible	This group defines additional all options for not related to direction of the call.
mscFrNniDnaCallOptionsEntry	1.3.6.1.4.1.562.36.2.1.70.2.13.1		not-accessible	An entry in the mscFrNniDnaCallOptionsTable.
U32 mscFrNniDnaAccountClass	1.3.6.1.4.1.562.36.2.1.70.2.13.1.10	Unsigned32	read-write	This attribute specifies the accounting class which is reserved for network operations usage. Its value is returned in the accounting record in the local and remote service type attributes. Use of this attribute is decided by network operator. This attribute is returned by the local VC in the accounting record for all calls that are set up using this particular DNA.
OCT mscFrNniDnaAccountCollection	1.3.6.1.4.1.562.36.2.1.70.2.13.1.11	OCTET STRING	read-write	This attribute indicates that accounting records are to be collected by the network for the various reasons: billing, test, study, auditing. The last of the parameters, force, indicates that accounting records are to be collected irrespective of other collection reasons. The force option is available for X.75 Gateways only. If none of these reasons are set, then accounting will be suppressed. To set a specific accounting collection reason, the reason is entered and the corresponding bit in the structure is set to a value of 1. To turn off a specific accounting collection reason, the reason is entered preceded with the '~' character, and the corresponding bit in the structure is set to a value of 0. The bit placement for the accounting collection reasons is as follows: Bit 0 - Bill Bit 1 - Test Bit 2 - Study Bit 3 - Audit Bit 4 - Force Description of bits: bill(0) test(1) study(2) audit(3) force(4)
U32 mscFrNniDnaServiceExchange	1.3.6.1.4.1.562.36.2.1.70.2.13.1.12	Unsigned32	read-write	This attribute is an arbitrary number, Data Service Exchange, as entered by the network operator and reported in accounting record. It is converted into an internal 8-bit integer value for use in the accounting record as well as in various X.25 and X.75 Tariff utilities.
INT mscFrNniDnaEgressAccounting	1.3.6.1.4.1.562.36.2.1.70.2.13.1.13	INTEGER	read-write	This attribute specifies if egress accounting is enabled by the frame relay service. If egress accounting is disabled, only segment counts are collected by the VC. No frame relay counts appear in the accounting records for the frame relay service. If egress accounting is enabled, the accounting records for the frame relay service will contain frame relay specific counts.
INT mscFrNniDnaDataPath	1.3.6.1.4.1.562.36.2.1.70.2.13.1.21	INTEGER	read-write	This attribute specifies the data path to be used by Virtual Circuits on this interface. If the connection has a DirectCall component then the value can be overridden by the dataPath attribute of the DirectCall component. This value applies to the connection after data transfer state is reached. All the data and control trafic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - dynamic packet routing system is used dprsMcsOnly - dprs Multi-Service Cut-Through Switching path is used. dprsMcsFirst - dprs Multi-Service Cut-Through Switching path is used if it is available. If it is not avaliable dprsOnly is used.
mscFrNniFramer	1.3.6.1.4.1.562.36.2.1.70.3
mscFrNniFramerRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.3.1		not-accessible	This entry controls the addition and deletion of mscFrNniFramer components.
mscFrNniFramerRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.3.1.1		not-accessible	A single entry in the table represents a single mscFrNniFramer component.
ROW mscFrNniFramerRowStatus	1.3.6.1.4.1.562.36.2.1.70.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniFramer components. These components can be added and deleted.
STR mscFrNniFramerComponentName	1.3.6.1.4.1.562.36.2.1.70.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniFramerStorageType	1.3.6.1.4.1.562.36.2.1.70.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniFramer tables.
NON mscFrNniFramerIndex	1.3.6.1.4.1.562.36.2.1.70.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniFramer tables.
mscFrNniFramerProvTable	1.3.6.1.4.1.562.36.2.1.70.3.10		not-accessible	This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
mscFrNniFramerProvEntry	1.3.6.1.4.1.562.36.2.1.70.3.10.1		not-accessible	An entry in the mscFrNniFramerProvTable.
LIN mscFrNniFramerInterfaceName	1.3.6.1.4.1.562.36.2.1.70.3.10.1.1	Link	read-write	This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
mscFrNniFramerLinkTable	1.3.6.1.4.1.562.36.2.1.70.3.11		not-accessible	This group contains attributes defining the framing of data on the link interface.
mscFrNniFramerLinkEntry	1.3.6.1.4.1.562.36.2.1.70.3.11.1		not-accessible	An entry in the mscFrNniFramerLinkTable.
INT mscFrNniFramerDataInversion	1.3.6.1.4.1.562.36.2.1.70.3.11.1.2	INTEGER	read-write	This attribute determines whether data bits are to be inverted (1 to 0 and 0 to 1) before transmission of frames to the interface. If the value of this attribute is On, the incoming data bits will also be inverted when frames are received from the link before being processed. This option is typically used in hdlc framing mode when inversion is used to guarantee 1's density. Note that aborts (in hdlc and interrupting modes) are corrupted when data is inverted. This attribute may only take its default value for non-MSA cards.
INT mscFrNniFramerFrameCrcType	1.3.6.1.4.1.562.36.2.1.70.3.11.1.3	INTEGER	read-write	This attribute defines the type of CRC used. The CRC value calculated is appended to the end of the frames transmitted to the link. The CRC value is removed from the end of frames received from the link and checked for correctness. NoCrc means that CRC is not used. This attribute may take only its default value for non-MSA cards.
U32 mscFrNniFramerFlagsBetweenFrames	1.3.6.1.4.1.562.36.2.1.70.3.11.1.4	Unsigned32	read-write	This attribute defines the number of flags that are inserted between frames sent to the link interface.
mscFrNniFramerStateTable	1.3.6.1.4.1.562.36.2.1.70.3.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscFrNniFramerStateEntry	1.3.6.1.4.1.562.36.2.1.70.3.12.1		not-accessible	An entry in the mscFrNniFramerStateTable.
INT mscFrNniFramerAdminState	1.3.6.1.4.1.562.36.2.1.70.3.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscFrNniFramerOperationalState	1.3.6.1.4.1.562.36.2.1.70.3.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscFrNniFramerUsageState	1.3.6.1.4.1.562.36.2.1.70.3.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscFrNniFramerStatsTable	1.3.6.1.4.1.562.36.2.1.70.3.13		not-accessible	This group contains the operational statistics data for a Framer component.
mscFrNniFramerStatsEntry	1.3.6.1.4.1.562.36.2.1.70.3.13.1		not-accessible	An entry in the mscFrNniFramerStatsTable.
C32 mscFrNniFramerFrmToIf	1.3.6.1.4.1.562.36.2.1.70.3.13.1.1	Counter32	read-only	The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
C32 mscFrNniFramerFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.3.13.1.2	Counter32	read-only	The number of frames received from the link interface by Framer.
C32 mscFrNniFramerOctetFromIf	1.3.6.1.4.1.562.36.2.1.70.3.13.1.3	Counter32	read-only	The number of bytes received from the link interface by Framer.
C32 mscFrNniFramerAborts	1.3.6.1.4.1.562.36.2.1.70.3.13.1.4	Counter32	read-only	This attribute is the total number of aborts received.
C32 mscFrNniFramerCrcErrors	1.3.6.1.4.1.562.36.2.1.70.3.13.1.5	Counter32	read-only	This attribute is the total number of frames with CRC errors, occurring in the receive direction from the link.
C32 mscFrNniFramerLrcErrors	1.3.6.1.4.1.562.36.2.1.70.3.13.1.6	Counter32	read-only	This attribute is the total number of frames with LRC errors, occurring in the Tx link prior to transmission onto the link.
C32 mscFrNniFramerNonOctetErrors	1.3.6.1.4.1.562.36.2.1.70.3.13.1.7	Counter32	read-only	This attribute is the total number of frames that were non octet aligned.
C32 mscFrNniFramerOverruns	1.3.6.1.4.1.562.36.2.1.70.3.13.1.8	Counter32	read-only	This attribute is the total number of frames received from the link for which overruns occurred.
C32 mscFrNniFramerUnderruns	1.3.6.1.4.1.562.36.2.1.70.3.13.1.9	Counter32	read-only	This attribute is the total number of frames transmitted to the link for which underruns occurred.
C32 mscFrNniFramerLargeFrmErrors	1.3.6.1.4.1.562.36.2.1.70.3.13.1.10	Counter32	read-only	This attribute is the total number of frames received which were too large. The frame execeeded the maximumFrameLengthLimit provisioned attribute or it contained more than the 255 block hardware limit.
C32 mscFrNniFramerFrmModeErrors	1.3.6.1.4.1.562.36.2.1.70.3.13.1.11	Counter32	read-only	This attribute is the total number of frames detected with framing mode errors. A framingModeError is flagged when frames are inconsistent with the specified framingType, that is when interrupting frames are used while running in hdlc mode.
NUM mscFrNniFramerFrmToIf64	1.3.6.1.4.1.562.36.2.1.70.3.13.1.14	PassportCounter64	read-only	The number of frames transmitted to the link interface by Framer. Note: This does not include the number of frames transmitted directly to the hardware queue, thus bypassing the Framer component.
NUM mscFrNniFramerFrmFromIf64	1.3.6.1.4.1.562.36.2.1.70.3.13.1.15	PassportCounter64	read-only	The number of frames received from the link interface by Framer.
NUM mscFrNniFramerOctetFromIf64	1.3.6.1.4.1.562.36.2.1.70.3.13.1.16	PassportCounter64	read-only	The number of bytes received from the link interface by Framer.
mscFrNniFramerUtilTable	1.3.6.1.4.1.562.36.2.1.70.3.14		not-accessible	This group contains the link utilizaiton operational data for a Framer component.
mscFrNniFramerUtilEntry	1.3.6.1.4.1.562.36.2.1.70.3.14.1		not-accessible	An entry in the mscFrNniFramerUtilTable.
G32 mscFrNniFramerNormPrioLinkUtilToIf	1.3.6.1.4.1.562.36.2.1.70.3.14.1.1	Gauge32	read-only	This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) sent to the link as a percentage of the available bandwidth on the link. Note that this indluces traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
G32 mscFrNniFramerNormPrioLinkUtilFromIf	1.3.6.1.4.1.562.36.2.1.70.3.14.1.3	Gauge32	read-only	This attribute is the utilization of the normal and high priority data traffic (interruptable traffic) received from the link as a percentage of the available bandwidth on the link. Note that this includes traffic with Transfer Priorities (TP) of 0, 6 and 9 and/or Emission Priority of 2 and 3. The utilization is the average for the last minute.
mscFrNniLmi	1.3.6.1.4.1.562.36.2.1.70.4
mscFrNniLmiRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.4.1		not-accessible	This entry controls the addition and deletion of mscFrNniLmi components.
mscFrNniLmiRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.4.1.1		not-accessible	A single entry in the table represents a single mscFrNniLmi component.
ROW mscFrNniLmiRowStatus	1.3.6.1.4.1.562.36.2.1.70.4.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniLmi components. These components cannot be added nor deleted.
STR mscFrNniLmiComponentName	1.3.6.1.4.1.562.36.2.1.70.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniLmiStorageType	1.3.6.1.4.1.562.36.2.1.70.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniLmi tables.
NON mscFrNniLmiIndex	1.3.6.1.4.1.562.36.2.1.70.4.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniLmi tables.
mscFrNniLmiParmsTable	1.3.6.1.4.1.562.36.2.1.70.4.10		not-accessible	This group contains the provisionable attributes of the Local Management Interface component.
mscFrNniLmiParmsEntry	1.3.6.1.4.1.562.36.2.1.70.4.10.1		not-accessible	An entry in the mscFrNniLmiParmsTable.
INT mscFrNniLmiProcedures	1.3.6.1.4.1.562.36.2.1.70.4.10.1.1	INTEGER	read-write	This attribute selects the procedures to be used for the Local Management Interface. The following are the supported procedures: none: Local Management Interface procedures are not running on this interface. This accommodates Frame Relay user equipment which didn't implement any LMI procedures. In this case, the remaining attributes of this group are ignored. ansi: Local Management Interface procedures from the ANSI specification are supported. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are supported. DLCI 0 is used for the LMI protocol. Was previously ccitt. autoConfigure: The interface determines automatically which Local Management Interface procedures to use. The procedures currently being used can be seen in the operational attribute opProcedures.
INT mscFrNniLmiAsyncStatusReport	1.3.6.1.4.1.562.36.2.1.70.4.10.1.2	INTEGER	read-write	This attribute selects the use of asynchronous PVC status report procedures as specified in ANSI and CCITT specification.
U32 mscFrNniLmiErrorEventThreshold	1.3.6.1.4.1.562.36.2.1.70.4.10.1.3	Unsigned32	read-write	For the network-side-procedure, an event is defined as follows: (1) receipt of a STATUS ENQUIRY message, or (2) expiration of timer T392. An error event is (1) nonreceipt of STATUS ENQUIRY in T392 seconds; (2) invalid format of a LMI message; (3) invalid receive sequence number. For the user-side-procedure, an event is defined as a polling cycle or a status enquiry and status report exchange. An error event is (1) non-receipt of a STATUS within the polling cycle, or (2) invalid format of a LMI message, or (3) invalid sequence number This attribute specifies the number of error events which, if they occur within eventCount events, will cause a protocol error condition. The condition is cleared after eventCount sequential correct events occur. It must be less than or equal to eventCount (n393)
U32 mscFrNniLmiEventCount	1.3.6.1.4.1.562.36.2.1.70.4.10.1.4	Unsigned32	read-write	This attribute specifies the number of contiguous events within which no more than eventErrorThreshold error events are allowed. It must be greater than or equal to errorEventThreshold (n392).
U32 mscFrNniLmiCheckPointTimer	1.3.6.1.4.1.562.36.2.1.70.4.10.1.5	Unsigned32	read-write	This attribute selects the time (in seconds) within which a STATUS ENQUIRY message is expected. It must be greater than linkVerificationTimer (t391).
INT mscFrNniLmiIgnoreActiveBit	1.3.6.1.4.1.562.36.2.1.70.4.10.1.7	INTEGER	read-write	This attribute specifies whether the Frame Relay LMI Active Bit (A-bit) has a bearing on the transfer of user data across this Frame Relay interface for both directions of traffic flow. When this attribute is set to yes, the A-bit status of a user DLCI connection does not affect data transfer. When this attribute is set to no, data received from the local interface is discarded if an A-bit =0 condition exists towards the local user. Data being sent to the local interface is discarded if an A- bit = 0 condition exists towards the local user.
mscFrNniLmiNniParmsTable	1.3.6.1.4.1.562.36.2.1.70.4.11		not-accessible	This group contains the provisionable attributes of the Local Management Interface component which are unique to NNI.
mscFrNniLmiNniParmsEntry	1.3.6.1.4.1.562.36.2.1.70.4.11.1		not-accessible	An entry in the mscFrNniLmiNniParmsTable.
U32 mscFrNniLmiFullStatusPollingCycles	1.3.6.1.4.1.562.36.2.1.70.4.11.1.1	Unsigned32	read-write	This attribute specifies how frequently the Frame Relay NNI service should initiate a Status Enquiry for a full PVC status report. A polling cycle is a Status Enquiry and Status Report exchange.
U32 mscFrNniLmiLinkVerificationTimer	1.3.6.1.4.1.562.36.2.1.70.4.11.1.2	Unsigned32	read-write	This attribute specifies how frequently the Frame Relay NNI service should initiate a Status Enquiry for link integrity verification. It must be less than checkPointTimer (t392).
mscFrNniLmiStateTable	1.3.6.1.4.1.562.36.2.1.70.4.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscFrNniLmiStateEntry	1.3.6.1.4.1.562.36.2.1.70.4.12.1		not-accessible	An entry in the mscFrNniLmiStateTable.
INT mscFrNniLmiAdminState	1.3.6.1.4.1.562.36.2.1.70.4.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscFrNniLmiOperationalState	1.3.6.1.4.1.562.36.2.1.70.4.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscFrNniLmiUsageState	1.3.6.1.4.1.562.36.2.1.70.4.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscFrNniLmiPsiTable	1.3.6.1.4.1.562.36.2.1.70.4.13		not-accessible	This group provides the protocol status of the Local Management Interface.
mscFrNniLmiPsiEntry	1.3.6.1.4.1.562.36.2.1.70.4.13.1		not-accessible	An entry in the mscFrNniLmiPsiTable.
INT mscFrNniLmiProtocolStatus	1.3.6.1.4.1.562.36.2.1.70.4.13.1.1	INTEGER	read-only	This attribute indicates whether the LMI is in an error condition or whether the LMI procedures are behaving normally. When operating with no LMI protocol, this attribute is always set to normalCondition. When operating with LMI procedures, this attribute is set to errorCondition after n392 of the last n393 events are in error. The consequence of an errorCondition is that all DLCIs on this interface will become inactive in both directions. The errorCondition is lifted and a normalCondition is indicated when a sufficient number of events have occurred without error. In ANSI, this occurs when n393 consecutive good events take place. If the procedures attribute is set to autoConfigure, this attribute is se to configuring while adaptive LMI determines which LMI procedures are running on the link. A single LMI error event during auto configuration causes the attribute value to change to errorCondition. If during configuring no LMI message is received, an LMI errorCondition is raised after n392 x t392 seconds.
INT mscFrNniLmiOpProcedures	1.3.6.1.4.1.562.36.2.1.70.4.13.1.2	INTEGER	read-only	This attribute indicates the procedures being used for the Local Management Interface. This attribute should be ignored if protocolStatus is not normalCondition. The following procedures are supported: none: Local Management Interface procedures are not running on this interface. This accommodates Frame Relay user equipment that has not implemented any LMI procedures. ansi: Local Management Interface procedures from the ANSI specification are running. DLCI 0 is used for the LMI protocol. itu: Local Management Interface procedures from the ITU-T specification are running. DLCI 0 is used for the LMI protocol. Was previously ccitt. unknown: Local Management Interface procedures have yet to be determined by Adaptive LMI.
mscFrNniLmiStatsTable	1.3.6.1.4.1.562.36.2.1.70.4.14		not-accessible	This group contains the operational statistics for the Frame Relay NNI Local Management Interface.
mscFrNniLmiStatsEntry	1.3.6.1.4.1.562.36.2.1.70.4.14.1		not-accessible	An entry in the mscFrNniLmiStatsTable.
C32 mscFrNniLmiKeepAliveStatusToIf	1.3.6.1.4.1.562.36.2.1.70.4.14.1.1	Counter32	read-only	This attribute counts the number of Local Management Interface keep alive status messages sent to the external network in response to a status enquiry for keep alive status. When the maximum count is exceeded it wraps to zero.
C32 mscFrNniLmiFullStatusToIf	1.3.6.1.4.1.562.36.2.1.70.4.14.1.2	Counter32	read-only	This attribute counts the number of Local Management Interface full status messages sent to the external network in response to a status enquiry for keep alive or full status. When the maximum count is exceeded it wraps to zero.
C32 mscFrNniLmiKeepAliveStatusEnqFromIf	1.3.6.1.4.1.562.36.2.1.70.4.14.1.3	Counter32	read-only	This attribute counts the number of Local Management Interface valid keep alive status enquiry messages received from the external network. When the maximum count is exceeded it wraps to zero.
C32 mscFrNniLmiFullStatusEnqFromIf	1.3.6.1.4.1.562.36.2.1.70.4.14.1.4	Counter32	read-only	This attribute counts the number of Local Management Interface valid full status enquiry messages received from the external network. When the maximum count is exceeded it wraps to zero.
STR mscFrNniLmiNetworkSideEventHistory	1.3.6.1.4.1.562.36.2.1.70.4.14.1.5	AsciiString	read-only	This attribute displays the Local Management Interface network side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The leftmost event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status enquiry message. An error event is either a nT2/T392 timer expiry or receipt of a status enquiry with bad sequence numbers.
STR mscFrNniLmiUserSideEventHistory	1.3.6.1.4.1.562.36.2.1.70.4.14.1.6	AsciiString	read-only	This attribute displays the Local Management Interface user side procedure event history in order of occurrence. An event is represented by a single symbol. A '+' symbol indicates a good event. An 'X' symbol indicates a protocol error event. The leftmost event is the most recent to occur. The provisioned eventCount (nN3/ N393) dictates the maximum number of events displayed. A good event is triggered by receipt of a valid status message. An error event is either a nT1/T391 timer expiry or receipt of a status message with bad sequence numbers.
C32 mscFrNniLmiProtocolErrors	1.3.6.1.4.1.562.36.2.1.70.4.14.1.7	Counter32	read-only	This attribute counts the number of Local Management Interface protocol errors. It is the sum of the sequence (sequenceErrors and statusSequenceErrors) and timeout (pollingVerifTimeouts and noStatusReportCount) errors. When the maximum count is exceeded it wraps to zero.
C32 mscFrNniLmiUnexpectedIes	1.3.6.1.4.1.562.36.2.1.70.4.14.1.8	Counter32	read-only	This attribute counts the number of Local Management Interface frames received with an Information Element identifier that is unknown or unexpected. An unexpected Information Element is not a protocol error. When the maximum count is exceeded, this counter wraps to zero.
C32 mscFrNniLmiSequenceErrors	1.3.6.1.4.1.562.36.2.1.70.4.14.1.9	Counter32	read-only	This attribute counts the number of Local Management Interface Status Enquiry message sequence errors. A sequence error is receipt of a Status Enquiry message with a receive sequence number not equal to the last send sequence number. When the maximum count is exceeded the counter wraps to zero.
C32 mscFrNniLmiStatusSequenceErrors	1.3.6.1.4.1.562.36.2.1.70.4.14.1.10	Counter32	read-only	This attribute counts the number of Local Management Interface Status message sequence errors. A sequence error is receipt of a Status message with a receive sequence number not equal to the last send sequence number. When the maximum count is exceeded the counter wraps to zero.
C32 mscFrNniLmiUnexpectedReports	1.3.6.1.4.1.562.36.2.1.70.4.14.1.11	Counter32	read-only	This attribute counts the number of Local Management Interface frames received with an unknown or unexpected report type. An unexpected report type is not a protocol error. When the maximum count is exceeded the counter wraps to zero.
C32 mscFrNniLmiPollingVerifTimeouts	1.3.6.1.4.1.562.36.2.1.70.4.14.1.12	Counter32	read-only	This attribute counts the number of checkPointTImer (t392) timer expiries occurring on the Local Management Interface. When the maximum count is exceeded the counter wraps to zero.
C32 mscFrNniLmiNoStatusReportCount	1.3.6.1.4.1.562.36.2.1.70.4.14.1.13	Counter32	read-only	This attribute counts the number of times when no status report or an invalid status report comes from the external network. This attribute is incremented in two cases: i) after a status enquiry is sent out and T391 timer expires without having a status report received. ii) an invalid status report is received. When the maximum count is exceeded it wraps to zero.
mscFrNniDlci	1.3.6.1.4.1.562.36.2.1.70.5
mscFrNniDlciRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.5.1		not-accessible	This entry controls the addition and deletion of mscFrNniDlci components.
mscFrNniDlciRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.5.1.1		not-accessible	A single entry in the table represents a single mscFrNniDlci component.
ROW mscFrNniDlciRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniDlci components. These components can be added and deleted.
STR mscFrNniDlciComponentName	1.3.6.1.4.1.562.36.2.1.70.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDlciStorageType	1.3.6.1.4.1.562.36.2.1.70.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDlci tables.
I32 mscFrNniDlciIndex	1.3.6.1.4.1.562.36.2.1.70.5.1.1.10	Integer32	not-accessible	This variable represents the index for the mscFrNniDlci tables.
mscFrNniDlciDc	1.3.6.1.4.1.562.36.2.1.70.5.2
mscFrNniDlciDcRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.5.2.1		not-accessible	This entry controls the addition and deletion of mscFrNniDlciDc components.
mscFrNniDlciDcRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.5.2.1.1		not-accessible	A single entry in the table represents a single mscFrNniDlciDc component.
ROW mscFrNniDlciDcRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniDlciDc components. These components cannot be added nor deleted.
STR mscFrNniDlciDcComponentName	1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDlciDcStorageType	1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDlciDc tables.
NON mscFrNniDlciDcIndex	1.3.6.1.4.1.562.36.2.1.70.5.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDlciDc tables.
mscFrNniDlciDcOptionsTable	1.3.6.1.4.1.562.36.2.1.70.5.2.10		not-accessible	This group defines attributes associated with a direct call. It defines connection in terms of path and call option parameters. This connection can be permanent (PVC), switched (SVC), or switched permanent (SPVC). It can have four facilities: - CCITT Facilities - DTE Facilities - National Facilities - International Facilities The total number of bytes of facilities including the facility codes and all of the facility data from all of the four classes of facilities must not exceed 512 bytes.
mscFrNniDlciDcOptionsEntry	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1		not-accessible	An entry in the mscFrNniDlciDcOptionsTable.
INT mscFrNniDlciDcRemoteNpi	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.3	INTEGER	read-write	This attribute specifies the Numbering Plan Indicator (NPI) of the remoteDna.
STR mscFrNniDlciDcRemoteDna	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.4	DigitString	read-write	This attribute specifies the Data Network Address (DNA) of the service at the remote end of the DLCI. This is the called (destination) DCE address (DNA) of this PVC.
U32 mscFrNniDlciDcRemoteDlci	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.5	Unsigned32	read-write	This attribute specifies the remote DLCI of the PVC connection.
INT mscFrNniDlciDcType	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.6	INTEGER	read-write	This attribute specifies the type of VC call. If the value is set to permanentMaster, then a permanent connection will be established between two ends. The remote end must be defined as a permanentSlave, permanentBackupSlave, or permanentSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as permanentMaster always initiates the calls. It attempts to call once per minute. If the value is set to permanentSlave then a permanent connection will be established between two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote end is defined as anything else. The permanentSlave end attempts to call once per minute. If the value is set to permanentSlaveWithBackup then a permanent connection will be established between the two ends. The remote end must be defined as a permanentMaster. The connection cannot be established if the remote interface is defined as anything else. The permanentSlaveWithBackup attempts to call once per minute. When type is set to permanentSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection which can be redirected to the permanentBackupSlave. If the value is set to permanentBackupSlave then a permanent connection is established between the two ends only if the permanentMaster end is disconnected from the permanentSlaveWithBackup end and a backup call is established by the call redirection system. If the permanentSlaveWithBackup interface becomes available again, the permanentBackupSlave end is disconnected and the permanentSlaveWithBackup end is reconnected to the permanentMaster end. The permanentBackupSlave end does not try to establish a call. If the value is set to spvcMaster, then a permanent connection is established between two ends, with resiliency at the NNI), if the connection transits across two or more networks. The remote end, which may be in the same network, or an external network that is reachable via Frame Relay NNIs, must be defined as either a spvcSlave, spvcBackupSlave or spvcSlaveWithBackup. The connection cannot be established if the remote end is defined as anything else. The end defined as spvcMaster always initiates the call. It attempts to call once per minute. The call is attempted by the spvcMaster and accepted by the remote end only if all of the following conditions are satisfied, at both ends: 1. The physical layer must be operational. 2. The LMI procedures must be in normalCondition (that is, no service affecting condition). 3. If the LMI side attribute is provisioned to both, the A-bit received from the interface must be Active. If the LMI side attribute is not provisioned to both, this condition does not apply. After a call is cleared, the spvcMaster end attempts to retry the call according to the rule for the clear cause. If the call is cleared or rejected due to the failure of one of the three conditions indicated above, or due to unavailability of resources along any point in the connection path, the call will be retried after 60 seconds. For all other causes, such as loss of service at an NNI, the call will be retried immediately. If the value is set to spvcSlave then an SPVC connection is established between two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote end is defined as anything else. The spvcSlave end does not attempt to call. If the value is set to spvcSlaveWithBackup then a SPVC connection is established between the two ends. The remote end must be defined as an spvcMaster. The connection cannot be established if the remote interface end is defined as anything else. Unlike a permanentSlaveWithBackup end, the spvcSlaveWithBackup end does not attempt to call. If the value is set to spvcSlaveWithBackup, the connection is cleared if the interface becomes unavailable. This enables a retry of the connection by the spvcMaster end, which may be redirected to an end that is set to spvcBackupSlave. If the value is set to spvcBackupSlave then an SPVC connection is established between the two ends only if the spvcMaster end is disconnected from the spvcSlaveWithBackup end, and a backup call is redirected by the call redirection system. Unlike the PVC connection, if the spvcSlaveWithBackup interface becomes available again, the spvcBackupSlave end is not disconnected and the spvcSlaveWithBackup end is not reconnected to the spvcMaster end. Neither the spvcBackupSlave nor the spvcSlaveWithBackup ends try to establish an SPVC call.
INT mscFrNniDlciDcTransferPriority	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.9	INTEGER	read-write	This attribute specifies the transfer priority to the local network for the outgoing calls using this particular DLCI. It overrides the defaultTransferPriority provisioned in its associated Dna component. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 levels from 0 to 15. Each transfer priority n, where n is the transfer priority index, has a default setting for routing class of service (multimedia, delay, or throughput) and Frame Relay egress queue (depending on the number of supported egress queues on the remote end interface). These settings are specified by the routingClassOfService and emissionPriority attributes provisioned under the Mod Frs DprsNet Tpm/n component. Specifying useDnaDefTP means using the value given by defaultTransferPriority in the associated Dna for this DLCI.
INT mscFrNniDlciDcDiscardPriority	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.10	INTEGER	read-write	This attribute specifies the discard priority for outgoing call using this DLCI. The discard priority has three provisioning values: normal, high, and useDnaDefPriority. Under congestion conditions, traffic with normal priority is discarded before traffic with high priority. The Dna default value (provisioned by outDefaultPriority) is taken if this attribute is set to the value useDnaDefPriority.
INT mscFrNniDlciDcDeDiscardPriority	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.11	INTEGER	read-write	This attribute specifies whether the discardPriority applies to DE frames for this DLCI. When set to determinedByDiscardPriority, traffic with DE bit set will be discarded according to the setting of the discardPriority. When set to lowest, all traffic with DE bit set is treated the same and is sent to the subnet at the lowest discard priority.
INT mscFrNniDlciDcDataPath	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.12	INTEGER	read-write	This attribute specifies the data path to be used by Virtual Circuits on this interface. The value of the dataPath attribute in the Dna component is overridden by this attribute if the value is not useDnaValue. This value applies to the connection after data transfer state is reached. All the data and control traffic will be sent using this data path. If the provisioned dataPath is not available the connection is not established. The value of the dataPath is signalled by both ends of the connection. If this value is not the same at both ends dprsOnly is used for the duration of the connection. A virtual circuit connection is always established using dprsOnly even if this attribute is provisioned as some other value. dprsOnly - The dynamic packet routing system is used. dprsMcsOnly - The DPRS Multi-Service Cut-Through Switching path is used. dprsMcsFirst - The DPRS Multi-Service Cut-Through Switching path is used if it is available. If it is not available, dprsOnly is used. useDnaValue - The routing system used is based on the value provisioned in the Dna component.
U32 mscFrNniDlciDcCugIndex	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.13	Unsigned32	read-write	This attribute specifies the CUG index which is to be signalled in PVC and SPVC call requests to the remote end. The type of CUG signalling is defined in attribute cugType in this component.
INT mscFrNniDlciDcCugType	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.14	INTEGER	read-write	This attribute specifies the type of CUG signalling to be used in PVC and SPVC call requests. Index of CUG to be used is defined in attribute cugIndex in this component. Possible values are: cug - signal CUG cugOa - signal CUG with outgoing access doNotSignal - no CUG in call request
INT mscFrNniDlciDcMapIpCosToFrQos	1.3.6.1.4.1.562.36.2.1.70.5.2.10.1.15	INTEGER	read-write	This attribute specifies whether an IP TOS value is mapped to an FR QOS. The mapping used is provisioned in the Mod Frs IpCosToFrQos component. When this attribute is set to yes, at Frame Relay egress, the IP TOS byte in each frame is checked. The TOS value determines the egress emission queue and the discard priority for that frame. When this attribute is set to no, FR QOS is determined by the provisioned discard priority and transfer priority.
mscFrNniDlciDcNfaTable	1.3.6.1.4.1.562.36.2.1.70.5.2.202		not-accessible	This is the i'th National facility required for this direct call. Within the provisioning system, the user specifies the facility code along with the facility parameters. The facility is represented internally as a hexadecimal string following the X.25 ITU-T representation for facility data. Two explicit attributes discardPriority and pathSensitivity are created to replace H.01 and H.30 in the group VcsDirectCallOptionsProv of this file. The migrate escape here (DcComponent::migrateFaxEscape) propagates the old provisioning data under H.01 and H.30 into discardPriority and transferPriority. The rule of the above propagation are: 0 in H.01 is equivalent to discardPriority 0; 1 in H.01 is equivalent to discardPriority 1. And 0 in H.30 is equivalent to transferPriority throughput; 1 in H.30 is equivalent to pathSensitivity delay. Please refer to discardPriority and pathSensitivity for more information on how to use them.
mscFrNniDlciDcNfaEntry	1.3.6.1.4.1.562.36.2.1.70.5.2.202.1		not-accessible	An entry in the mscFrNniDlciDcNfaTable.
I32 mscFrNniDlciDcNfaIndex	1.3.6.1.4.1.562.36.2.1.70.5.2.202.1.1	Integer32	not-accessible	This variable represents the index for the mscFrNniDlciDcNfaTable.
STR mscFrNniDlciDcNfaValue	1.3.6.1.4.1.562.36.2.1.70.5.2.202.1.2	HexString	read-write	This variable represents an individual value for the mscFrNniDlciDcNfaTable.
ROW mscFrNniDlciDcNfaRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.2.202.1.3	RowStatus	write-only	This variable is used to control the addition and deletion of individual values of the mscFrNniDlciDcNfaTable.
mscFrNniDlciVc	1.3.6.1.4.1.562.36.2.1.70.5.3
mscFrNniDlciVcRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.5.3.1		not-accessible	This entry controls the addition and deletion of mscFrNniDlciVc components.
mscFrNniDlciVcRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.5.3.1.1		not-accessible	A single entry in the table represents a single mscFrNniDlciVc component.
ROW mscFrNniDlciVcRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniDlciVc components. These components cannot be added nor deleted.
STR mscFrNniDlciVcComponentName	1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDlciVcStorageType	1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDlciVc tables.
NON mscFrNniDlciVcIndex	1.3.6.1.4.1.562.36.2.1.70.5.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDlciVc tables.
mscFrNniDlciVcCadTable	1.3.6.1.4.1.562.36.2.1.70.5.3.10		not-accessible	This group represents operational call data related to Frame Relay Vc. It can be displayed only for Frame Relay Vc which is created by application.
mscFrNniDlciVcCadEntry	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1		not-accessible	An entry in the mscFrNniDlciVcCadTable.
INT mscFrNniDlciVcType	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.1	INTEGER	read-only	This attribute displays the type of call, pvc,svc,spvc or frf10spvc.
INT mscFrNniDlciVcState	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.2	INTEGER	read-only	This attribute displays the state of call control. P5 state is not supported but is listed for completness. Transitions from one state to another take very short time. state most often displayed is dataTransferP4.
INT mscFrNniDlciVcPreviousState	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.3	INTEGER	read-only	This attribute displays the previous state of call control. This is a valuable field to determine how the processing is progressing.
U32 mscFrNniDlciVcDiagnosticCode	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.4	Unsigned32	read-only	This attribute displays the internal substate of call control. It is used to further refine state of call processing.
U32 mscFrNniDlciVcPreviousDiagnosticCode	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.5	Unsigned32	read-only	This attribute displays the internal substate of call control. It is used to further refine state of call processing.
INT mscFrNniDlciVcCalledNpi	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.6	INTEGER	read-only	This attribute displays the Numbering Plan Indicator (NPI) of the called end.
STR mscFrNniDlciVcCalledDna	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.7	DigitString	read-only	This attribute displays the Data Network Address (Dna) of the called (destination) DTE to which this call is sent. This address if defined at recieving end will complete Vc connection.
U32 mscFrNniDlciVcCalledLcn	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.8	Unsigned32	read-only	This attribute displays the Logical Channel Number of the called end. It is valid only after both ends of Vc exchanged relevant information.
INT mscFrNniDlciVcCallingNpi	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.9	INTEGER	read-only	This attribute displays the Numbering Plan Indicator (NPI) of the calling end.
STR mscFrNniDlciVcCallingDna	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.10	DigitString	read-only	This attribute displays the Data Network Address (Dna) of the calling end.
U32 mscFrNniDlciVcCallingLcn	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.11	Unsigned32	read-only	This attribute displays the Logical Channel Number of the calling end.
INT mscFrNniDlciVcAccountingEnabled	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.12	INTEGER	read-only	This attribute indicates that this optional section of accounting record is suppressed or permitted. If accountingEnabled is yes, conditions for generation of accounting record were met. These conditions include billing options, vc recovery conditions and Module wide accounting data options.
INT mscFrNniDlciVcFastSelectCall	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.13	INTEGER	read-only	This attribute displays that this is a fast select call.
INT mscFrNniDlciVcPathReliability	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.19	INTEGER	read-only	This attribute displays the path reliability.
INT mscFrNniDlciVcAccountingEnd	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.20	INTEGER	read-only	This attribute indicates if this end should generate an accounting record. Normally, callingEnd is the end to generate an accounting record.
INT mscFrNniDlciVcPriority	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.21	INTEGER	read-only	This attribute displays whether the call is a normal or a high priority call.
U32 mscFrNniDlciVcSegmentSize	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.22	Unsigned32	read-only	This attribute displays the segment size (in bytes) used on the call. It is used to calculate the number of segments transmitted and received.
U32 mscFrNniDlciVcMaxSubnetPktSize	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.27	Unsigned32	read-only	This attribute indicates the maximum packet size allowed on the Vc.
INT mscFrNniDlciVcRcosToNetwork	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.28	INTEGER	read-only	This attribute indicates the routing metric routing class of service to the network.
INT mscFrNniDlciVcRcosFromNetwork	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.29	INTEGER	read-only	This attribute displays the routing metric Routing Class of Service from the Network.
INT mscFrNniDlciVcEmissionPriorityToNetwork	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.30	INTEGER	read-only	This attribute displays the network internal emission priotity to the network.
INT mscFrNniDlciVcEmissionPriorityFromNetwork	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.31	INTEGER	read-only	This attribute displays the network internal emission priotity from the network.
STR mscFrNniDlciVcDataPath	1.3.6.1.4.1.562.36.2.1.70.5.3.10.1.32	AsciiString	read-only	This attribute indicates the data path used by the connection. The data path is provisioned in Dna and DirectCall components. The displayed value of this attribute can be different from the provisioned value. If the connection is using dprsOnly data path, the string dprsOnly is displayed. (dynamic packet routing system) If the connection is using dprsMcsOnly data path, the string dprsMcsOnly is displayed. If the connection is using dprsMcsFirst data path, the string dprsMcsFirst is displayed.
mscFrNniDlciVcIntdTable	1.3.6.1.4.1.562.36.2.1.70.5.3.11		not-accessible	This group defines display of interval data collected by Vc. Data in this group is variable and may depend on time when this display command is issued.
mscFrNniDlciVcIntdEntry	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1		not-accessible	An entry in the mscFrNniDlciVcIntdTable.
HEX mscFrNniDlciVcCallReferenceNumber	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.1	Hex	read-only	This attribute is obsolete. It is replaced by the callReferenceNumber attribute to display the call reference number in decimal. The SNMP reference for the callReferenceNumber attribute is callReferenceNumberDecimal.
U32 mscFrNniDlciVcElapsedTimeTillNow	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.2	Unsigned32	read-only	This attribute displays the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since Vc started.
U32 mscFrNniDlciVcSegmentsRx	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.3	Unsigned32	read-only	This attribute displays the number of segments received at the time command was issued. This is the segment received count maintained by accounting at each end of the Vc. This counter is updated only when the packet cannot be successfully delivered out of the sink Vc and to the sink AP Conditions in which packets may be discarded by the sink Vc include: missing packets due to subnet discards, segmentation protocol violations due to subnet discard, duplicated and out-of-ranged packets and packets that arrive while Vc is in path recovery state.
U32 mscFrNniDlciVcSegmentsSent	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.4	Unsigned32	read-only	This attribute displays the number of segments sent at the time command was issued. This is the segment sent count maintained by accounting at the source Vc. Vc only counts packets that Vc thinks can be delivered successfully into the subnet. In reality, these packets may be dropped by trunking, for instance. This counter is not updated when splitting fails, when Vc is in a path recovery state, when packet forwarding fails to forward this packet and when subsequent packets have to be discarded as we want to minimize the chance of out-of-sequence and do not intentionally send out-of- sequenced packets into the subnet.
ENT mscFrNniDlciVcStartTime	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.5	EnterpriseDateAndTime	read-only	This attribute displays the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes.
U32 mscFrNniDlciVcCallReferenceNumberDecimal	1.3.6.1.4.1.562.36.2.1.70.5.3.11.1.7	Unsigned32	read-only	This attribute displays the call reference number which is a unique number generated by the switch.The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the call.
mscFrNniDlciVcFrdTable	1.3.6.1.4.1.562.36.2.1.70.5.3.12		not-accessible	This group defines Frame Relay attributes collected by Frame Relay Vc. The purpose of Vc attributes is to aid end users and verification people to understand the Vc internal behavior. This is particularly useful when the network has experienced abnormality and we want to isolate problems and pinpoint trouble spots. Attributes are collected on a per Vc basis. Until a need is identified, statistics are not collected at a processor level. Each attribute is stored in a 32 bit field and is initialized to zero when a Vc enters into the data transfer state. When a PVC is disconnected and then connected again, the attributes will be reset. Attributes cannot be reset through other methods. Frame Relay Vc uses a best effort data packet delivery protocol and a different packet segmentation and combination methods from the General Vc. The Frame Relay Vc uses the same call setup and control mechanism (e.g. the support of non-flow control data packets) as in a General Vc. Most General Vc statistics and internal variables are used in a Frame Relay Vc and are displayed by software developers
mscFrNniDlciVcFrdEntry	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1		not-accessible	An entry in the mscFrNniDlciVcFrdTable.
U32 mscFrNniDlciVcFrmCongestedToSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.2	Unsigned32	read-only	This attribute displays the number of frames from link discarded due to lack of resources. It keeps track of the number of frames from link that have to be discarded. The discard reasons include insufficient memory for splitting the frame into smaller subnet packet size.
U32 mscFrNniDlciVcCannotForwardToSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.3	Unsigned32	read-only	This attribute displays the number of discarded packets that can not be forwarded into the subnet because of subnet congestion. Number of frames from link discarded due to failure in forwarding a packet from Vc into the subnet.- This attribute is increased when packet forwarding fails to forward a packet into the subnet. If a frame is split into multiple subnet packets and a partial packet has to be discarded, all subsequent partial packets that have not yet been delivered to the subnet will be discarded as well.
U32 mscFrNniDlciVcNotDataXferToSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.4	Unsigned32	read-only	This attribute records the number of frames from link discarded when the Vc tries to recover from internal path failure.
U32 mscFrNniDlciVcOutOfRangeFrmFromSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.5	Unsigned32	read-only	This attribute displays the number of frames from subnet discarded due to out of sequence range for arriving too late.
U32 mscFrNniDlciVcCombErrorsFromSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.6	Unsigned32	read-only	This attribute records the number of subnet packets discarded at the sink Vc due to the Vc segmentation and combination protocol error. Usually, this occurs when the subnet discards packets and thus this statistics can be used to guest the number of subnet packets that are not delivered to the Vc. It cannot be used as an actual measure because some subnet packets may have been delivered to Vc but have to be discarded because these are partial packets to a frame in which some other partial packets have not been properly delivered to Vc
U32 mscFrNniDlciVcDuplicatesFromSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.7	Unsigned32	read-only	This attribute displays the number of subnet packets discarded due to duplication. Although packets are not retransmitted by the Frame Relay Vc, it is possible for the subnet to retransmit packets. When packets are out-of-sequenced and copies of the same packets arrive, then this attribute is increased.
U32 mscFrNniDlciVcNotDataXferFromSubnet	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.8	Unsigned32	read-only	This attribute displays the number of subnet packets discarded when data transfer is suspended in Vc recovery.
U32 mscFrNniDlciVcFrmLossTimeouts	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.9	Unsigned32	read-only	This attribute displays the number of lost frame timer expiries. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
U32 mscFrNniDlciVcOoSeqByteCntExceeded	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.10	Unsigned32	read-only	This attribute displays the number times that the out of sequence byte threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
U32 mscFrNniDlciVcPeakOoSeqPktCount	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.11	Unsigned32	read-only	This attribute displays the frame relay peak packet count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
U32 mscFrNniDlciVcPeakOoSeqFrmForwarded	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.12	Unsigned32	read-only	This attribute displays the frame relay peak size of the sequence packet queue. The subnet may deliver packets out-of- sequenced. These packets are then queued in an out-of-sequenced queue, waiting for a packet with the expected sequence number to come. When that packet arrives, this attribute records the maximum number of packets that were out-of-sequenced, but now have become in-sequenced. The statistics is used to measure expected queue size due to normal subnet packet disorder (not due to subnet packet discard). Current implementation also uses this statistics to set a maximum size for the out-of-sequenced queue.
U32 mscFrNniDlciVcSendSequenceNumber	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.13	Unsigned32	read-only	This attribute displays the Vc internal packet's send sequence number. Note that a 'packet' in this context, may be either a user data packet, or an OAM frame.
U32 mscFrNniDlciVcPktRetryTimeouts	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.15	Unsigned32	read-only	This attribute displays the number of packets which have retransmission time-outs. When this count is excessive, the network is very congested and packets have been discarded in the subnet.
U32 mscFrNniDlciVcPeakRetryQueueSize	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.16	Unsigned32	read-only	This attribute displays the peak size of retransmission queue. This attribute is used as an indicator of the acknowledgment behavior across the subnet. Records the largest body of unacknowledged packets.
U32 mscFrNniDlciVcSubnetRecoveries	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.17	Unsigned32	read-only	This attribute displays the number of successful Vc recovery attempts.
U32 mscFrNniDlciVcOoSeqPktCntExceeded	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.19	Unsigned32	read-only	This attribute displays the number times that the out of sequence packet threshold is exceeded. When the threshold is exceeded, this condition is treated as if the loss frame timer has expired and all frames queued at the sink Vc are delivered to the AP. We need to keep this count to examine if the threshold is engineered properly. This should be used in conjunction with the peak value of out-of- sequenced queue and the number of times the loss frame timer has expired. This count should be relatively small when compared with loss frame timer expiry count.
U32 mscFrNniDlciVcPeakOoSeqByteCount	1.3.6.1.4.1.562.36.2.1.70.5.3.12.1.20	Unsigned32	read-only	This attribute displays the frame relay peak byte count of the out of sequence queue. This attribute records the maximum queue length of the out-of-sequenced queue. The counter can be used to deduce the message buffer requirement on a Vc.
mscFrNniDlciVcDmepTable	1.3.6.1.4.1.562.36.2.1.70.5.3.417		not-accessible	This attribute displays the data path used by the connection. Data path is provisioned in Dna and DirectCall components. If the connection is using dprsOnly data path, this attribute is empty. If the connection is using dprsMcsOnly or dprsMcsFirst data path, this attribute displays component name of the dprsMcsEndPoint.
mscFrNniDlciVcDmepEntry	1.3.6.1.4.1.562.36.2.1.70.5.3.417.1		not-accessible	An entry in the mscFrNniDlciVcDmepTable.
NUM mscFrNniDlciVcDmepValue	1.3.6.1.4.1.562.36.2.1.70.5.3.417.1.1	RowPointer	read-only	This variable represents both the value and the index for the mscFrNniDlciVcDmepTable.
mscFrNniDlciSp	1.3.6.1.4.1.562.36.2.1.70.5.4
mscFrNniDlciSpRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.5.4.1		not-accessible	This entry controls the addition and deletion of mscFrNniDlciSp components.
mscFrNniDlciSpRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.5.4.1.1		not-accessible	A single entry in the table represents a single mscFrNniDlciSp component.
ROW mscFrNniDlciSpRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniDlciSp components. These components cannot be added nor deleted.
STR mscFrNniDlciSpComponentName	1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDlciSpStorageType	1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDlciSp tables.
NON mscFrNniDlciSpIndex	1.3.6.1.4.1.562.36.2.1.70.5.4.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDlciSp tables.
mscFrNniDlciSpParmsTable	1.3.6.1.4.1.562.36.2.1.70.5.4.11		not-accessible	This group contains the provisionable attributes for the Data Link Connection Identifier. These attributes reflect the service parameters specific to this instance of DLCI . The congestion control attributes in this group are defined in T1.606 Addendum 1.
mscFrNniDlciSpParmsEntry	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1		not-accessible	An entry in the mscFrNniDlciSpParmsTable.
U32 mscFrNniDlciSpMaximumFrameSize	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.1	Unsigned32	read-write	This attribute specifies the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
INT mscFrNniDlciSpRateEnforcement	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.2	INTEGER	read-write	This attribute specifies whether rate enforcement is in effect for this user Data Link Connection on this Frame Relay interface. Turning on rate enforcement means that CIR and DE=1 traffic will be measured and enforced. Turning off rate enforcement means that all frames from the user will be accepted and no modifications to the frame with respect to the DE bit will be made.
G32 mscFrNniDlciSpCommittedInformationRate	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.3	Gauge32	read-write	This attribute specifies the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, Bc must also be 0.
G32 mscFrNniDlciSpCommittedBurstSize	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.4	Gauge32	read-write	This attribute specifies the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute is ignored when rateEnforcement is off. If rateEnforcement is on and this attribute is 0, cir must also be 0.
G32 mscFrNniDlciSpExcessBurstSize	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.5	Gauge32	read-write	This attribute specifies the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. CIR, Bc, and Be cannot all be zero when rateEnforcement is on.
U32 mscFrNniDlciSpMeasurementInterval	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.6	Unsigned32	read-write	When cir and bc are zero and rateEnforcement is on, this attribute must be provisioned to specify the time interval (in milliseconds) over which rates and burst sizes are measured. When cir and bc are non-zero, the time interval is internally calculated and is not shown. In that situation, this field is ignored, and is not representative of the time interval. This attribute is ignored when rateEnforcement is off, or when cir and bc are non-zero. If rateEnforcement is on and both cir and bc are zero, this field must be non-zero.
INT mscFrNniDlciSpRateAdaptation	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.7	INTEGER	read-write	This attribute specifies whether rate adaptation is in effect for this user Data Link Connection on this Frame Relay interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This pro-active measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be set to on eirOnly or cirProportionate if rateEnforcement is turned on.
INT mscFrNniDlciSpAccounting	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.8	INTEGER	read-write	This attribute specifies whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
U32 mscFrNniDlciSpRaSensitivity	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.9	Unsigned32	read-write	This attribute specifies the sensitivity of the rate adaptation system. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favour the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is turned off.
INT mscFrNniDlciSpUpdateBCI	1.3.6.1.4.1.562.36.2.1.70.5.4.11.1.10	INTEGER	read-write	This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updatBCI is set to off, then incoming BECN bits will have no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remotedna and remotedlci attributes of the dc component of the dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote dlci is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If the rateAdaptation attribute of the remote dlci is provisioned to off, then the setting of updateBCI attribute here will have no effect..
mscFrNniDlciLb	1.3.6.1.4.1.562.36.2.1.70.5.5
mscFrNniDlciLbRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.5.5.1		not-accessible	This entry controls the addition and deletion of mscFrNniDlciLb components.
mscFrNniDlciLbRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.5.5.1.1		not-accessible	A single entry in the table represents a single mscFrNniDlciLb component.
ROW mscFrNniDlciLbRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniDlciLb components. These components cannot be added nor deleted.
STR mscFrNniDlciLbComponentName	1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDlciLbStorageType	1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDlciLb tables.
NON mscFrNniDlciLbIndex	1.3.6.1.4.1.562.36.2.1.70.5.5.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDlciLb tables.
mscFrNniDlciLbStatsTable	1.3.6.1.4.1.562.36.2.1.70.5.5.10		not-accessible	This group contains all the statistics for the data loopback tool.
mscFrNniDlciLbStatsEntry	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1		not-accessible	An entry in the mscFrNniDlciLbStatsTable.
U32 mscFrNniDlciLbLocalTotalFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.1	Unsigned32	read-only	This attribute records the number of frames looped back to the link since loopback was last started.
U32 mscFrNniDlciLbLocalTotalBytes	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.2	Unsigned32	read-only	This attribute records the number of bytes looped back to the link since loopback mode was started.
U32 mscFrNniDlciLbLocalFecnFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.3	Unsigned32	read-only	This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the link since the loopback mode was started.
U32 mscFrNniDlciLbLocalBecnFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.4	Unsigned32	read-only	This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the link since the loopback mode was started.
U32 mscFrNniDlciLbLocalDeFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.5	Unsigned32	read-only	This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
U32 mscFrNniDlciLbLocalDeBytes	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.6	Unsigned32	read-only	This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the link since the loopback mode was started.
U32 mscFrNniDlciLbRemoteTotalFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.7	Unsigned32	read-only	This attribute records the number of frames looped back to the subnet since loopback was last started.
U32 mscFrNniDlciLbRemoteTotalBytes	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.8	Unsigned32	read-only	This attribute records the number of bytes looped back to the subnet since loopback was last started.
U32 mscFrNniDlciLbRemoteFecnFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.9	Unsigned32	read-only	This attribute records the number of frames with the Forward Explicit Congestion Notification (FECN) bit set, looped back to the subnet since the loopback mode was started.
U32 mscFrNniDlciLbRemoteBecnFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.10	Unsigned32	read-only	This attribute records the number of frames with the Backward Explicit Congestion Notification (BECN) bit set, looped back to the subnet since the loopback mode was started.
U32 mscFrNniDlciLbRemoteDeFrm	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.13	Unsigned32	read-only	This attribute records the number of frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
U32 mscFrNniDlciLbRemoteDeBytes	1.3.6.1.4.1.562.36.2.1.70.5.5.10.1.14	Unsigned32	read-only	This attribute records the number of bytes in frames with the Discard Eligibility (DE) bit set, looped back to the subnet since the loopback mode was started.
mscFrNniDlciEgressSp	1.3.6.1.4.1.562.36.2.1.70.5.6
mscFrNniDlciEgressSpRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.5.6.1		not-accessible	This entry controls the addition and deletion of mscFrNniDlciEgressSp components.
mscFrNniDlciEgressSpRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.5.6.1.1		not-accessible	A single entry in the table represents a single mscFrNniDlciEgressSp component.
ROW mscFrNniDlciEgressSpRowStatus	1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniDlciEgressSp components. These components cannot be added nor deleted.
STR mscFrNniDlciEgressSpComponentName	1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniDlciEgressSpStorageType	1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniDlciEgressSp tables.
NON mscFrNniDlciEgressSpIndex	1.3.6.1.4.1.562.36.2.1.70.5.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniDlciEgressSp tables.
mscFrNniDlciEgressSpProvTable	1.3.6.1.4.1.562.36.2.1.70.5.6.10		not-accessible	This group contains the provisionable attributes for this component.
mscFrNniDlciEgressSpProvEntry	1.3.6.1.4.1.562.36.2.1.70.5.6.10.1		not-accessible	An entry in the mscFrNniDlciEgressSpProvTable.
U32 mscFrNniDlciEgressSpCommittedInformationRate	1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.1	Unsigned32	read-write	This attribute specifies the committed information rate (CIR) for the egress direction. It is used for Call Admission Control (CAC) at the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the committedInformationRate attribute under the ServiceParameters component. VALUES ( 50000001 = sameAsServiceParameters )
U32 mscFrNniDlciEgressSpCommittedBurstSize	1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.2	Unsigned32	read-write	This attribute specifies the committed burst size (Bc) for the egress direction. It is used for performing Call Admission Control (CAC) at the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the committedBurstSize attribute under the ServiceParameters component. VALUES ( 50000001 = sameAsServiceParameters )
U32 mscFrNniDlciEgressSpExcessBurstSize	1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.3	Unsigned32	read-write	This attribute specifies the excess burst size (Be) for the egress direction. It is used for Call Admission Control (CAC) function towards the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the excessBurstSize attribute under the ServiceParameters component. VALUES ( 50000001 = sameAsServiceParameters )
U32 mscFrNniDlciEgressSpMeasurementInterval	1.3.6.1.4.1.562.36.2.1.70.5.6.10.1.4	Unsigned32	read-write	This attribute specifies the time interval over which rates and burst sizes are measured in the egress direction. It is used for bandwidth reservation for Call Admission Control (CAC) towards the egress link. If the value is set to sameAsSp, the value of this attribute is the same as the measurementInterval attribute under the ServiceParameters component. VALUES ( 25501 = sameAsServiceParameters )
mscFrNniDlciStateTable	1.3.6.1.4.1.562.36.2.1.70.5.10		not-accessible	This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
mscFrNniDlciStateEntry	1.3.6.1.4.1.562.36.2.1.70.5.10.1		not-accessible	An entry in the mscFrNniDlciStateTable.
INT mscFrNniDlciAdminState	1.3.6.1.4.1.562.36.2.1.70.5.10.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
INT mscFrNniDlciOperationalState	1.3.6.1.4.1.562.36.2.1.70.5.10.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
INT mscFrNniDlciUsageState	1.3.6.1.4.1.562.36.2.1.70.5.10.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OCT mscFrNniDlciAvailabilityStatus	1.3.6.1.4.1.562.36.2.1.70.5.10.1.4	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OCT mscFrNniDlciProceduralStatus	1.3.6.1.4.1.562.36.2.1.70.5.10.1.5	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OCT mscFrNniDlciControlStatus	1.3.6.1.4.1.562.36.2.1.70.5.10.1.6	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OCT mscFrNniDlciAlarmStatus	1.3.6.1.4.1.562.36.2.1.70.5.10.1.7	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
INT mscFrNniDlciStandbyStatus	1.3.6.1.4.1.562.36.2.1.70.5.10.1.8	INTEGER	read-only	If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
INT mscFrNniDlciUnknownStatus	1.3.6.1.4.1.562.36.2.1.70.5.10.1.9	INTEGER	read-only	This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
mscFrNniDlciAbitTable	1.3.6.1.4.1.562.36.2.1.70.5.12		not-accessible	This group contains the A-Bit status information for this Data Link Connection Identifier.
mscFrNniDlciAbitEntry	1.3.6.1.4.1.562.36.2.1.70.5.12.1		not-accessible	An entry in the mscFrNniDlciAbitTable.
INT mscFrNniDlciABitStatusToIf	1.3.6.1.4.1.562.36.2.1.70.5.12.1.1	INTEGER	read-only	This attribute is the most recent A-bit status sent to the interface. The A-bit status is part of the LMI protocol, and indicates willingness to accept data from the local interface. inactive - the Frame Relay service discards all data offered from the local interface. active - the Frame Relay service tries to process all data offered from the local interface. notApplicable - the DLCI is switched, so this attribute is ignored.
INT mscFrNniDlciABitReasonToIf	1.3.6.1.4.1.562.36.2.1.70.5.12.1.2	INTEGER	read-only	This attribute provides the reason (if any) for an inactive status to be sent to the interface. This reason is notApplicable for an active status.
INT mscFrNniDlciABitStatusFromIf	1.3.6.1.4.1.562.36.2.1.70.5.12.1.3	INTEGER	read-only	This attribute is the most recent A-Bit status received from the interface. inactive - the Frame Relay service informs the remote DLCI not to send user data to this interface. active - the Frame Relay service informs the remote DLCI that it is okay to send user data to this interface. notApplicable - the DLCI is switched, so this attribute is ignored.
INT mscFrNniDlciABitReasonFromIf	1.3.6.1.4.1.562.36.2.1.70.5.12.1.4	INTEGER	read-only	This attribute provides the reason (if any) for an inactive status to be sent to the subnet. This reason is notApplicable for an active status.
INT mscFrNniDlciLoopbackState	1.3.6.1.4.1.562.36.2.1.70.5.12.1.5	INTEGER	read-only	This attribute has the value on when the DLCI is in loopback mode and off otherwise. The loopback command verbs start and stop are used to initiate and terminate the loopback mode for a DLCI. While loopbackState is on, the local LMI will report to the interface the A- bit status as active. Also an active A-bit signal will be reliably propagated across the subnet to the remote DLCI.
mscFrNniDlciSpOpTable	1.3.6.1.4.1.562.36.2.1.70.5.13		not-accessible	This group defines the service and traffic parameters specific to this instance of DLCI. In the case of permanent (PVC and P-SPVC) DLCIs, the values of attributes with the exception of the measurementInterval reflect the provisioning under the FrNni Dlci Sp component. In the case of switched (SVC and S-SPVC) DLCIs, the values of attributes reflect the service parameter negotiations between what is provisioned under the FrNni Sig component and the signaled parameters.
mscFrNniDlciSpOpEntry	1.3.6.1.4.1.562.36.2.1.70.5.13.1		not-accessible	An entry in the mscFrNniDlciSpOpTable.
U32 mscFrNniDlciMaximumFrameSize	1.3.6.1.4.1.562.36.2.1.70.5.13.1.1	Unsigned32	read-only	This attribute indicates the maximum number of octets which may be included in the information field. The frame relay header and CRC octets are not included in this definition. This attribute corresponds to the dN1 parameter described in the Vendor Forum Specification.
INT mscFrNniDlciRateEnforcement	1.3.6.1.4.1.562.36.2.1.70.5.13.1.2	INTEGER	read-only	This attribute is obsolete. It provided the information which is now represented by the provisionable attribute rateEnforcement under the ServiceParameters component.
U32 mscFrNniDlciCommittedInformationRate	1.3.6.1.4.1.562.36.2.1.70.5.13.1.3	Unsigned32	read-only	This attribute indicates the committed information rate (CIR) in bits per second (bit/s). When rateEnforcement is set to on, cir is the rate at which the network agrees to transfer information under normal conditions. This rate is measured over a measurement interval (t) that is determined internally based on CIR and the committed burst size (Bc). An exception to this occurs when CIR is provisioned to be zero, in which case the measurement interval (t) must be provisioned explicitly. This attribute should be ignored when rateEnforcement is off.
U32 mscFrNniDlciCommittedBurstSize	1.3.6.1.4.1.562.36.2.1.70.5.13.1.4	Unsigned32	read-only	This attribute indicates the committed burst size (Bc) in bits. bc is the amount of data that a network agrees to transfer under normal conditions over a measurement interval (t). Data marked DE=1 is not accounted for in Bc. This attribute should be ignored when rateEnforcement is off.
U32 mscFrNniDlciExcessBurstSize	1.3.6.1.4.1.562.36.2.1.70.5.13.1.5	Unsigned32	read-only	This attribute indicates the excess burst size (Be) in bits. Be is the amount of uncommitted data that the network will attempt to deliver over measurement interval T. Data marked DE=1 by the user or by the network is accounted for here. This attribute should be ignored when rateEnforcement is off.
U32 mscFrNniDlciMeasurementInterval	1.3.6.1.4.1.562.36.2.1.70.5.13.1.6	Unsigned32	read-only	This attribute indicates the time interval (in milliseconds) over which rates and burst sizes are measured. This attribute should be ignored when rateEnforcement is off.
INT mscFrNniDlciRateAdaptation	1.3.6.1.4.1.562.36.2.1.70.5.13.1.7	INTEGER	read-only	This attribute is obsolete. It provided the information which is now represented by the provisionable attribute rateAdaptation under the ServiceParameters component.
INT mscFrNniDlciAccounting	1.3.6.1.4.1.562.36.2.1.70.5.13.1.8	INTEGER	read-only	This attribute indicates whether accounting data collection and record generation is turned on at this DLCI. For accounting data collection and record generation to be turned on, the accountingOn bit and at least one of the accountCollection bits in the DataNetworkAddress component must be set to on.
INT mscFrNniDlciEmissionPriorityToIf	1.3.6.1.4.1.562.36.2.1.70.5.13.1.9	INTEGER	read-only	This attribute indicates the emission priority of frames sent to the interface. A larger value denotes a higher priority.
U32 mscFrNniDlciTransferPriToNwk	1.3.6.1.4.1.562.36.2.1.70.5.13.1.10	Unsigned32	read-only	This attribute indicates the priority at which data is transferred to the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay, or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
U32 mscFrNniDlciTransferPriFromNwk	1.3.6.1.4.1.562.36.2.1.70.5.13.1.11	Unsigned32	read-only	This attribute indicates the priority at which data is transferred from the network. The transfer priority is a preference configured for an application according to its delay-sensitivity requirement. Frames with higher transfer priority are served by the network before the frames with lower priority. The transfer priority standard is defined to have 16 indices from 0 to 15. Each transfer priority n, where n specifies the transfer priority index, contains a default setting for routing class of service (multimedia, delay, or throughput) and frame relay egress queue (depending on the number of supported egress queues on the remote end interface) specified by the routingClassOfService and emissionPriority attributes provisioned in the Mod Frs DprsNet Tpm/n component. The default mapping can be altered by a user if required.
mscFrNniDlciStatsTable	1.3.6.1.4.1.562.36.2.1.70.5.14		not-accessible	This group contains the operational statistics for the Frame Relay Data Link Connection Identifier.
mscFrNniDlciStatsEntry	1.3.6.1.4.1.562.36.2.1.70.5.14.1		not-accessible	An entry in the mscFrNniDlciStatsTable.
U32 mscFrNniDlciFrmToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.1	Unsigned32	read-only	This attribute counts the frames sent out the interface. When the maximum count is reached the count wraps to zero.
U32 mscFrNniDlciFecnFrmToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.2	Unsigned32	read-only	This attribute counts the frames sent to the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciBecnFrmToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.3	Unsigned32	read-only	This attribute counts the frames sent to the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciBciToSubnet	1.3.6.1.4.1.562.36.2.1.70.5.14.1.4	Unsigned32	read-only	This attribute counts the frames sent into the local network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDeFrmToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.5	Unsigned32	read-only	This attribute counts the frames sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDiscCongestedToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.6	Unsigned32	read-only	This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciDiscDeCongestedToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.7	Unsigned32	read-only	This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion in the direction toward the interface. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.8	Unsigned32	read-only	This attribute counts the frames received from the interface. It includes the frames that are discarded due to error or excess. When the maximum count is reached the count wraps to zero.
U32 mscFrNniDlciFecnFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.9	Unsigned32	read-only	This attribute counts the frames received from the interface with the Forward Explicit Congestion Notification (FECN) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciBecnFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.10	Unsigned32	read-only	This attribute counts the frames received from the interface with the Backward Explicit Congestion Notification (BECN) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciFciFromSubnet	1.3.6.1.4.1.562.36.2.1.70.5.14.1.11	Unsigned32	read-only	This attribute counts the frames received from the network with the Forward Congestion Indication (FCI) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciBciFromSubnet	1.3.6.1.4.1.562.36.2.1.70.5.14.1.12	Unsigned32	read-only	This attribute counts the frames received from the network with the Backward Congestion Indication (BCI) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDeFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.13	Unsigned32	read-only	This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciExcessFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.14	Unsigned32	read-only	This attribute counts the frames received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDiscExcessFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.15	Unsigned32	read-only	This attribute counts the frames which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDiscFrameAbit	1.3.6.1.4.1.562.36.2.1.70.5.14.1.16	Unsigned32	read-only	This attribute counts the number of frame discards at the Frame Relay Service, due to an inactive PVC status, in the direction toward the local network. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciDiscCongestedFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.17	Unsigned32	read-only	This attribute counts the number of frame discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciDiscDeCongestedFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.18	Unsigned32	read-only	This attribute counts the number of discarded frames, with the Discard Eligibility (DE) bit set, at the Frame Relay service, due to local congestion, in the direction toward the local network. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciErrorShortFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.19	Unsigned32	read-only	This attribute counts the frames received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciErrorLongFrmFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.20	Unsigned32	read-only	This attribute counts the frames received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Frames whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
U32 mscFrNniDlciBecnFrmSetByService	1.3.6.1.4.1.562.36.2.1.70.5.14.1.21	Unsigned32	read-only	This attribute counts the number of frames with BECN set by the Frame Relay service. It is incremented whenever the Frame Relay service sets BECN on a frame upon detecting local congestion. This count is incremented regardless of whether the frame already bears a set BECN bit since its use is to determine the place of congestion. When the count reaches maximum, it wraps to zero.
U32 mscFrNniDlciBytesToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.22	Unsigned32	read-only	This attribute counts the bytes sent out the interface. When the maximum count is reached the count wraps to zero.
U32 mscFrNniDlciDeBytesToIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.23	Unsigned32	read-only	This attribute counts the bytes sent to the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDiscCongestedToIfBytes	1.3.6.1.4.1.562.36.2.1.70.5.14.1.24	Unsigned32	read-only	This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the link. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciDiscDeCongestedToIfBytes	1.3.6.1.4.1.562.36.2.1.70.5.14.1.25	Unsigned32	read-only	This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the link. When the maximum count is reached the count wraps to zero.
U32 mscFrNniDlciBytesFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.26	Unsigned32	read-only	This attribute counts the bytes received from the interface. Bytes that are discarded due to error or excess are not counted. When the maximum count is reached the count wraps to zero.
U32 mscFrNniDlciDeBytesFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.27	Unsigned32	read-only	This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit set. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciExcessBytesFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.28	Unsigned32	read-only	This attribute counts the bytes received from the interface with the Discard Eligibility (DE) bit clear, but subsequently set by the network due to rate enforcement. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDiscExcessFromIfBytes	1.3.6.1.4.1.562.36.2.1.70.5.14.1.29	Unsigned32	read-only	This attribute counts the bytes which were discarded due to rate enforcement. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciDiscByteAbit	1.3.6.1.4.1.562.36.2.1.70.5.14.1.30	Unsigned32	read-only	This attribute counts the bytes which were discarded due to aBit turned off.
U32 mscFrNniDlciDiscCongestedFromIfBytes	1.3.6.1.4.1.562.36.2.1.70.5.14.1.31	Unsigned32	read-only	This attribute counts the number of byte discards at the Frame Relay service due to local congestion in the direction toward the network. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciDiscDeCongestedFromIfBytes	1.3.6.1.4.1.562.36.2.1.70.5.14.1.32	Unsigned32	read-only	This attribute counts the number of discard eligible (DE=1) byte discards at the Frame Relay service due to local congestion in the direction toward the network. When the maximum count is reached the count wraps to zero.
U32 mscFrNniDlciErrorShortBytesFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.33	Unsigned32	read-only	This attribute counts the bytes received with 0 octets in the information field. When the count reaches maximum it wraps to zero.
U32 mscFrNniDlciErrorLongBytesFromIf	1.3.6.1.4.1.562.36.2.1.70.5.14.1.34	Unsigned32	read-only	This attribute counts the bytes received with number of octets in the information field greater than the subscribed maximum. When the count reaches maximum it wraps to zero. Bytes whose lengths are greater than the hardware receive buffer are ignored by the hardware and are therefore not included in this count.
U32 mscFrNniDlciRateAdaptReduct	1.3.6.1.4.1.562.36.2.1.70.5.14.1.35	Unsigned32	read-only	This attribute counts the number of rate reductions due to rate adaptation. Rate adaptation causes the allowed rate to be reduced in steps. After each reduction, a period of time is awaited before further action is taken. At the end of this period, the allowed rate is further reduced if congestion is still prevalent. When this count reaches maximum, it wraps to zero.
U32 mscFrNniDlciRateAdaptReductPeriod	1.3.6.1.4.1.562.36.2.1.70.5.14.1.36	Unsigned32	read-only	This attribute provides a cumulative count of the amount of time that rate adaptation procedures have been in effect. When this count reaches maximum, it wraps to zero.
INT mscFrNniDlciTransferPriorityToNetwork	1.3.6.1.4.1.562.36.2.1.70.5.14.1.37	INTEGER	read-only	This attribute is obsolete. It is replaced by attribute transferPriorityToNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
INT mscFrNniDlciTransferPriorityFromNetwork	1.3.6.1.4.1.562.36.2.1.70.5.14.1.38	INTEGER	read-only	This attribute is obsolete. It is replaced by attribute transferPriorityFromNetwork under group FrsNniDataLinkConnectionIdentifierServiceParametersOp.
U32 mscFrNniDlciCirPresent	1.3.6.1.4.1.562.36.2.1.70.5.14.1.39	Unsigned32	read-only	This attribute provides the actual Committed Information Rate (CIR) enforced for this DLCI. This number is in units of 800 bits/ sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned CIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed CIR at the moment that this attribute is collected.
U32 mscFrNniDlciEirPresent	1.3.6.1.4.1.562.36.2.1.70.5.14.1.40	Unsigned32	read-only	This attribute provides the actual Excess Information Rate (EIR) enforced for this DLCI. This number is in units of 800 bits/sec, since that is the internal resolution of Passport rate enforcement. If rateEnforcement is off, then this number does not have meaning. Normally, this attribute matches the provisioned EIR for the DLCI. But when Rate Adaptation is active, then this number will vary to represent the actual Allowed EIR at the moment that this attribute is collected.
mscFrNniDlciIntTable	1.3.6.1.4.1.562.36.2.1.70.5.15		not-accessible	This group contains the operational statistics for the Frame Relay Data Link Connection Identifier interval data (accounting data).
mscFrNniDlciIntEntry	1.3.6.1.4.1.562.36.2.1.70.5.15.1		not-accessible	An entry in the mscFrNniDlciIntTable.
ENT mscFrNniDlciStartTime	1.3.6.1.4.1.562.36.2.1.70.5.15.1.1	EnterpriseDateAndTime	read-only	This attribute indicates the start time of this interval period. If Vc spans 12 hour time or time of day change startTime reflects new time as recorded at 12 hour periods or time of day changes. A new interval period is started each time an accounting record is generated.
UNS mscFrNniDlciTotalIngressBytes	1.3.6.1.4.1.562.36.2.1.70.5.15.1.2	Unsigned64	read-only	This attribute counts the total bytes received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
UNS mscFrNniDlciTotalEgressBytes	1.3.6.1.4.1.562.36.2.1.70.5.15.1.3	Unsigned64	read-only	This attribute counts the total bytes sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
UNS mscFrNniDlciEirIngressBytes	1.3.6.1.4.1.562.36.2.1.70.5.15.1.4	Unsigned64	read-only	This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
UNS mscFrNniDlciEirEgressBytes	1.3.6.1.4.1.562.36.2.1.70.5.15.1.5	Unsigned64	read-only	This attribute counts the total bytes with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
UNS mscFrNniDlciDiscardedBytes	1.3.6.1.4.1.562.36.2.1.70.5.15.1.6	Unsigned64	read-only	This attribute counts the total bytes in invalid frames received from the interface and discarded at the DLCI since the start of the interval period. This count is a sum of octets in frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
U32 mscFrNniDlciTotalIngressSegFrm	1.3.6.1.4.1.562.36.2.1.70.5.15.1.7	Unsigned32	read-only	If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames received from the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames received from the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
U32 mscFrNniDlciTotalEgressSegFrm	1.3.6.1.4.1.562.36.2.1.70.5.15.1.8	Unsigned32	read-only	If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the total number of segments in frames sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the total number of frames sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
U32 mscFrNniDlciEirIngressSegFrm	1.3.6.1.4.1.562.36.2.1.70.5.15.1.9	Unsigned32	read-only	If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the subnet since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated.
U32 mscFrNniDlciEirEgressSegFrm	1.3.6.1.4.1.562.36.2.1.70.5.15.1.10	Unsigned32	read-only	If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of frames with the Discard Eligibility (DE) bit set sent to the interface since the start of the interval period. The start of the interval period is captured in the startTime attribute. The count is reset to zero when an accounting record is generated
U32 mscFrNniDlciDiscardedSegFrm	1.3.6.1.4.1.562.36.2.1.70.5.15.1.11	Unsigned32	read-only	If the value of the unitsCounted attribute in moduleData component is segments, this attribute counts the number of segments in invalid frames received from the interface and discarded at the DLCI. If the value of the unitsCounted attribute in moduleData component is frames, this attribute counts the number of invalid frames received from the interface and discarded at the DLCI. Segments of frames are counted since the start of the interval period. The count is reset to zero when an accounting record is generated. The count is a sum of segments in frames or frames discarded due to the number of octets in the information field greater than the subscribed maximum or equal to 0, due to aBit turned off, or due to rate enforcement.
U32 mscFrNniDlciCirPresentObs	1.3.6.1.4.1.562.36.2.1.70.5.15.1.12	Unsigned32	read-only	This attribute has moved to the statistics subgroup. See cirPresent..
U32 mscFrNniDlciEirPresentObs	1.3.6.1.4.1.562.36.2.1.70.5.15.1.13	Unsigned32	read-only	This attribute has moved to the statistics group. See eirPresent.
INT mscFrNniDlciRateEnforcementPresent	1.3.6.1.4.1.562.36.2.1.70.5.15.1.14	INTEGER	read-only	This attribute is obsolete. See the provisionable rateEnforcement attribute.
INT mscFrNniDlciRateAdaptationPresent	1.3.6.1.4.1.562.36.2.1.70.5.15.1.15	INTEGER	read-only	This attribute is obsolete. See the provisionable rateAdaptation attribute.
INT mscFrNniDlciLocalRateAdaptOccurred	1.3.6.1.4.1.562.36.2.1.70.5.15.1.16	INTEGER	read-only	This attribute indicates whether rate adaptation has occurred on this user Data Link Connection on this Frame Relay interface. The value is set to no when an accounting record is generated.
HEX mscFrNniDlciCallReferenceNumber	1.3.6.1.4.1.562.36.2.1.70.5.15.1.17	Hex	read-only	This attribute is obsoleted and replaced by callRefNumber.
U32 mscFrNniDlciElapsedDifference	1.3.6.1.4.1.562.36.2.1.70.5.15.1.18	Unsigned32	read-only	This attribute indicates the elapsed time representing the period of this interval data. It is elapsed time in 0.1 second increments since the call started.
U32 mscFrNniDlciCallRefNumber	1.3.6.1.4.1.562.36.2.1.70.5.15.1.20	Unsigned32	read-only	This attribute indicates the call reference number which is a unique number generated by the switch. The same Call Reference Number is stored in the interval data (accounting record) at both ends of the call. It can be used as one of the attributes in matching duplicate records generated at each end of the connection.
mscFrNniDlciCalldTable	1.3.6.1.4.1.562.36.2.1.70.5.16		not-accessible	This group of attributes describes the characteristics of the call such as call type and call state.
mscFrNniDlciCalldEntry	1.3.6.1.4.1.562.36.2.1.70.5.16.1		not-accessible	An entry in the mscFrNniDlciCalldTable.
INT mscFrNniDlciCallType	1.3.6.1.4.1.562.36.2.1.70.5.16.1.1	INTEGER	read-only	This attribute indicates whether this DLCI is a permancent virtual circuit (PVC), a switched virtual circuit (SVC), or a switched permament virtual circuit (SPVC).
INT mscFrNniDlciCallState	1.3.6.1.4.1.562.36.2.1.70.5.16.1.2	INTEGER	read-only	This attribute indicates the FRF.10 state of a switched call. The value of this attribute for a permanent (PVC and P-SPVC) DLCI is always notApplicable. In the description that follows, 'calling STE' refers to the network who has initiated the SETUP request, and 'called STE' refers to the network that receives the request. State description: In the null state, the network has neither received nor sent call setup requests for this DLCI. In the callInitiated state, the called STE has received a SETUP message from the calling STE. In the callProceedingSent state, the called STE has sent a CALL PROCEEDING message to the calling STE in response to the SETUP message. In the callPresent state, the calling STE has sent a SETUP message to the called STE but has not received a response. In the callProceedingReceived state, the calling STE has received a CALL PROCEEDING message from the called STE in response to a SETUP message. In the active state, either the called STE has sent a CONNECT message to the calling STE, or the calling STE has received a CONNECT from the called STE. In the releaseRequest state, the STE has sent a RELEASE message to release the call and is waiting for a RELEASE COMPLETE message. In the releaseIndication state, the STE has received a RELEASE and sends a RELEASE COMPLETE message after releasing the relevant call resources. In the restartRequest state, the STE has sent a RESTART request to the other STE and is waiting for an acknowledgement. In the restart state, the STE has received a request for a restart from the other STE and this STE has not returned an acknowledgement.
U32 mscFrNniDlciCallReference	1.3.6.1.4.1.562.36.2.1.70.5.16.1.3	Unsigned32	read-only	This attribute indicates the FRF.10 call reference number associated with this DLCI. The value of this attribute for a provisioned (PVC or P-SPVC) DLCI is always 0.
mscFrNniVFramer	1.3.6.1.4.1.562.36.2.1.70.6
mscFrNniVFramerRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.6.1		not-accessible	This entry controls the addition and deletion of mscFrNniVFramer components.
mscFrNniVFramerRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.6.1.1		not-accessible	A single entry in the table represents a single mscFrNniVFramer component.
ROW mscFrNniVFramerRowStatus	1.3.6.1.4.1.562.36.2.1.70.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniVFramer components. These components can be added and deleted.
STR mscFrNniVFramerComponentName	1.3.6.1.4.1.562.36.2.1.70.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniVFramerStorageType	1.3.6.1.4.1.562.36.2.1.70.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniVFramer tables.
NON mscFrNniVFramerIndex	1.3.6.1.4.1.562.36.2.1.70.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniVFramer tables.
mscFrNniVFramerProvTable	1.3.6.1.4.1.562.36.2.1.70.6.10		not-accessible	This group contains provisionable attributes for the VirtualFramer component.
mscFrNniVFramerProvEntry	1.3.6.1.4.1.562.36.2.1.70.6.10.1		not-accessible	An entry in the mscFrNniVFramerProvTable.
LIN mscFrNniVFramerOtherVirtualFramer	1.3.6.1.4.1.562.36.2.1.70.6.10.1.1	Link	read-write	This attribute specifies the other VirtualFramer to which the service is linked, for example, FrUni/n VirtualFramer, FrDte/n VirtualFramer.
LIN mscFrNniVFramerLogicalProcessor	1.3.6.1.4.1.562.36.2.1.70.6.10.1.2	Link	read-write	This attribute specifies the logical processor on which the service component will reside.
mscFrNniVFramerStateTable	1.3.6.1.4.1.562.36.2.1.70.6.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscFrNniVFramerStateEntry	1.3.6.1.4.1.562.36.2.1.70.6.11.1		not-accessible	An entry in the mscFrNniVFramerStateTable.
INT mscFrNniVFramerAdminState	1.3.6.1.4.1.562.36.2.1.70.6.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscFrNniVFramerOperationalState	1.3.6.1.4.1.562.36.2.1.70.6.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscFrNniVFramerUsageState	1.3.6.1.4.1.562.36.2.1.70.6.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscFrNniVFramerStatsTable	1.3.6.1.4.1.562.36.2.1.70.6.12		not-accessible	This group contains the operational statistics data for a VirtualFramer component.
mscFrNniVFramerStatsEntry	1.3.6.1.4.1.562.36.2.1.70.6.12.1		not-accessible	An entry in the mscFrNniVFramerStatsTable.
NUM mscFrNniVFramerFrmToOtherVFramer	1.3.6.1.4.1.562.36.2.1.70.6.12.1.2	PassportCounter64	read-only	This attribute counts the frames transmitted to the otherVirtualFramer.
NUM mscFrNniVFramerFrmFromOtherVFramer	1.3.6.1.4.1.562.36.2.1.70.6.12.1.3	PassportCounter64	read-only	This attribute counts the frames received from the otherVirtualFramer.
NUM mscFrNniVFramerOctetFromOtherVFramer	1.3.6.1.4.1.562.36.2.1.70.6.12.1.5	PassportCounter64	read-only	This attribute counts the octets received from the otherVirtualFramer.
mscFrNniSig	1.3.6.1.4.1.562.36.2.1.70.8
mscFrNniSigRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.8.1		not-accessible	This entry controls the addition and deletion of mscFrNniSig components.
mscFrNniSigRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.8.1.1		not-accessible	A single entry in the table represents a single mscFrNniSig component.
ROW mscFrNniSigRowStatus	1.3.6.1.4.1.562.36.2.1.70.8.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniSig components. These components can be added and deleted.
STR mscFrNniSigComponentName	1.3.6.1.4.1.562.36.2.1.70.8.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniSigStorageType	1.3.6.1.4.1.562.36.2.1.70.8.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniSig tables.
NON mscFrNniSigIndex	1.3.6.1.4.1.562.36.2.1.70.8.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniSig tables.
mscFrNniSigProvTable	1.3.6.1.4.1.562.36.2.1.70.8.11		not-accessible	This group contains common provisionable attributes for signaling at the interface.
mscFrNniSigProvEntry	1.3.6.1.4.1.562.36.2.1.70.8.11.1		not-accessible	An entry in the mscFrNniSigProvTable.
INT mscFrNniSigDlciAllocation	1.3.6.1.4.1.562.36.2.1.70.8.11.1.3	INTEGER	read-write	This attribute specifies the order in which DLCIs are dynamically allocated for SVCs. The purpose of this attribute is to prevent DLCI collisions between SVCs initiated by two FrNni interfaces talking to each other. This is achieved by provisioning a different value for this attribute at each end of the NNI link. A value of fromLowEnd specifies that the DLCI number assignment for SVC connections is initiated from the lowest value of the range (that is, highestPvcDlci+1 up to 1007). A value of fromHighEnd specifies that the DLCI number assignment for SVC connections is initiated from the highest value of the range (that is, 1007 down to highestPvcDlci+1).
U32 mscFrNniSigHighestPermanentDlci	1.3.6.1.4.1.562.36.2.1.70.8.11.1.4	Unsigned32	read-write	This attribute specifies the highest DLCI value that can be provisioned for a permanent connection. It partitions the DLCI space into permanent and switched connections. Permanent DLCI numbers higher than this value cannot be provisioned. The value 0 is used to indicate that no permanent connections are allowed on this interface. The value 1007 indicates that no switched connections are allowed on this interface.
U32 mscFrNniSigHighestPvcDlci	1.3.6.1.4.1.562.36.2.1.70.8.11.1.5	Unsigned32	read-write	This attribute specifies the highest DLCI value that can be provisioned for a permanent connection. It partitions the DLCI space into permanent and switched connections. Permanent DLCI numbers higher than this value cannot be provisioned. The value 0 is used to indicate that no permanent connections are allowed on this interface. The value 1007 indicates that no switched connections are allowed on this interface.
mscFrNniSigServParmsTable	1.3.6.1.4.1.562.36.2.1.70.8.12		not-accessible	This group contains the provisionable service parameters.
mscFrNniSigServParmsEntry	1.3.6.1.4.1.562.36.2.1.70.8.12.1		not-accessible	An entry in the mscFrNniSigServParmsTable.
U32 mscFrNniSigMaximumFrameSize	1.3.6.1.4.1.562.36.2.1.70.8.12.1.1	Unsigned32	read-write	This attribute specifies the maximum number of octets that may be included in the information field of the user DLCI of any switched connections using this interface. Its value must not be smaller than the value of defaultMaximumFrameSize.
U32 mscFrNniSigDefaultMaximumFrameSize	1.3.6.1.4.1.562.36.2.1.70.8.12.1.2	Unsigned32	read-write	This attribute specifies the default maximum number of octets that may be included in the information field of the user DLCI assigned for any switched connections using this interface. This value is used during call parameter negotiation for switched calls on this interface when the maximum frame size is not specified in the user's SETUP message. The value of this attribute must not exceed the value of the maximumFrameSize attribute.
U32 mscFrNniSigDefaultCommittedInformationRate	1.3.6.1.4.1.562.36.2.1.70.8.12.1.3	Unsigned32	read-write	This attribute specifies the default user to network direction CIR. This value is used during call parameter negotiation for switched calls on this interface when the CIR is not specified in the user's SETUP message.
U32 mscFrNniSigDefaultCommittedBurstSize	1.3.6.1.4.1.562.36.2.1.70.8.12.1.4	Unsigned32	read-write	This attribute specifies the default user to network direction Bc. This value is used during call parameter negotiation for switched calls on this interface when the Bc is not specified in the user's SETUP message.
U32 mscFrNniSigDefaultExcessBurstSize	1.3.6.1.4.1.562.36.2.1.70.8.12.1.5	Unsigned32	read-write	This attribute specifies the default user to network direction Be. This value is used during call parameter negotiation for switched calls on this interface when the Be is not specified in the user's SETUP message.
INT mscFrNniSigRateEnforcement	1.3.6.1.4.1.562.36.2.1.70.8.12.1.6	INTEGER	read-write	This attribute specifies whether rate enforcement is in effect for SVCs on this interface.
INT mscFrNniSigRateAdaptation	1.3.6.1.4.1.562.36.2.1.70.8.12.1.7	INTEGER	read-write	This attribute specifies whether closed-loop rate adaptation is in effect for SVCs on this interface. Rate adaptation is a feature that, in periods of congestion, adapts the rate at which the user is allowed to send data into the network to that which the network is able to handle at that time. This proactive measure of handling congestion optimizes network resources by causing the ingress to discard frames that would otherwise be discarded in the network. If this attribute is set to on, then, at the onset of congestion, the excess information rate (EIR) is reduced to a very low rate. If congestion persists, then the allowed CIR is reduced geometrically by 25% of the current value at that time. The minimum to which CIR can be reduced is 1/16th (6.25%) of the provisioned value. As congestion alleviates, CIR is increased linearly by 6.25% of the provisioned value specified in committedInformationRate. If set to eirOnly, then rate adaptation will only apply to the excess information rate (EIR). At the onset of congestion, the allowed EIR is reduced by 25% of its provisioned value. If congestion persists, EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. If set to cirProportionate, then rate adaptation will also only apply to the excess information rate (EIR). At the onset of congestion the initial allowed EIR is set to a multiple of the provisioned CIR. If congestion persists, the allowed EIR is reduced geometrically by 25% of the current value at that time. As congestion alleviates, EIR is gradually increased linearly by 6.25% of the provisioned EIR. Note that the allowed EIR may be set higher than the provisioned EIR, since it is calculated initially using another parameter, the provisioned CIR. If the allowed EIR at the moment is higher than the provisioned EIR, then the provisioned EIR is used instead. This attribute can only be set to on or eirOnly if rateEnforcement is set to on.
U32 mscFrNniSigRaSensitivity	1.3.6.1.4.1.562.36.2.1.70.8.12.1.8	Unsigned32	read-write	This attribute specifies the sensitivity of the rate adaptation system for all switched connections on this interface. A higher number indicates a higher sensitivity and therefore a quicker reaction time to network conditions. A quicker reaction time allows the network to discard frames at the access and protect network resources, but can lead to false alarms and a greater fluctuation of the allowed rate. A higher setting therefore tends to favor the protection of the network over the allowed throughput of the user. A lower number indicates a lower sensitivity and therefore a slower reaction to network conditions. A slower reaction time results in a greater amount of user traffic allowed into the network, but can lead to a waste of network bandwidth since the traffic may be discarded at the congested resource. A lower setting therefore tends to favour the allowed throughput of the user over the protection of the network. This attribute is applicable for adapting EIR when rateAdaptation is eirOnly or cirProportionate, or CIR when rateAdaptation is on. This attribute is ignored if rateAdaptation is off.
INT mscFrNniSigUpdateBCI	1.3.6.1.4.1.562.36.2.1.70.8.12.1.9	INTEGER	read-write	This attribute specifies whether internal Backward Congestion Indication (BCI) bits will report congestion external to the Passport network, as communicated through incoming BECN bits. If updateBCI is set to on, then BCI bits for incoming frames will be set if the BECN on the frame is set. If updateBCI is set to off, then incoming BECN bits has no effect. Setting updateBCI on for a DLCI means that the remote end of the DLCI, which is specified by the remoteDna and remoteDlci attributes of the Dc component of the Dlci, may perform Rate Adaptation using the flow of incoming BECN bits, in addition to internal Passport congestion management systems. If the rateAdaptation attribute of the remote DLCI is provisioned as eirOnly, cirProportionate, or on, then congestion from another network connected to a Passport network may trigger dynamic congestion management. If there is no rate adaptation at the other end, then the setting of updateBCI attribute here will have no effect.
mscFrNniSigSysParmsTable	1.3.6.1.4.1.562.36.2.1.70.8.13		not-accessible	This group contains the provisionable FRF.10 system parameters.
mscFrNniSigSysParmsEntry	1.3.6.1.4.1.562.36.2.1.70.8.13.1		not-accessible	An entry in the mscFrNniSigSysParmsTable.
U32 mscFrNniSigCallSetupTimer	1.3.6.1.4.1.562.36.2.1.70.8.13.1.1	Unsigned32	read-write	This attribute specifies the time this interface waits for a response to the SETUP message sent to the adjacent network. Upon timer expiry, the SETUP message is retransmitted. The second expiry of this timer causes the call to be cleared.
U32 mscFrNniSigReleaseTimer	1.3.6.1.4.1.562.36.2.1.70.8.13.1.2	Unsigned32	read-write	This attribute specifies the time this interface waits for a response to the RELEASE message sent to the adjacent network. Upon timer expiry, the RELEASE message is retransmitted. The second expiry of the timer causes the call to be released.
U32 mscFrNniSigCallProceedingTimer	1.3.6.1.4.1.562.36.2.1.70.8.13.1.3	Unsigned32	read-write	This attribute specifies the time this interface waits for the CONNECT message from the adjacent network after the network has received the optional CALL PROCEEDING message from the adjacent network. Upon timer expiry, the call is cleared.
U32 mscFrNniSigRestartReqTimer	1.3.6.1.4.1.562.36.2.1.70.8.13.1.4	Unsigned32	read-write	This attribute specifies the time this interface waits for the RESTART ACKNOWLEDGE message from the adjacent network after sending a first RESTART message. Upon timer expiry, another RESTART message is sent. After the second expiry, the interface is treated as idle. If the restartReqTimer attribute is set to the default value, then the interface is treated as idle when it receives an indication that the link is up and does not send a RESTART message.
U32 mscFrNniSigRestartRcvTimer	1.3.6.1.4.1.562.36.2.1.70.8.13.1.5	Unsigned32	read-write	This attribute specifies the time this interface waits for the processing of a RESTART message received by the interface. Upon expiry of this timer, an alarm will be displayed to report the problem. The timer value must be less than the restartReqTimer provisioned value at the adjacent node.
U32 mscFrNniSigStatusEnqTimer	1.3.6.1.4.1.562.36.2.1.70.8.13.1.6	Unsigned32	read-write	This attribute specifies the time the network waits for the requested STATUS message from the adjacent network. Upon expiry of this timer, another STATUS ENQUIRY message will be sent.
INT mscFrNniSigNetworkType	1.3.6.1.4.1.562.36.2.1.70.8.13.1.7	INTEGER	read-write	This attribute specifies whether this Frame Relay service is running on a public or a private network. This value is used solely in populating applicable information elements within those signaling messages that require a public or private network indication.
mscFrNniSigLapfSysTable	1.3.6.1.4.1.562.36.2.1.70.8.14		not-accessible	This group contains the provisionable attributes for the SVC data link layer. The data link layer is governed primarily through ITU specification Q.922, and operates over DLCI 0.
mscFrNniSigLapfSysEntry	1.3.6.1.4.1.562.36.2.1.70.8.14.1		not-accessible	An entry in the mscFrNniSigLapfSysTable.
U32 mscFrNniSigWindowSize	1.3.6.1.4.1.562.36.2.1.70.8.14.1.2	Unsigned32	read-write	This attribute specifies the window size. This is the maximum number of unacknowledged sequenced frames that may be outstanding from or to this interface at any one time.
U32 mscFrNniSigRetransmitLimit	1.3.6.1.4.1.562.36.2.1.70.8.14.1.3	Unsigned32	read-write	This attribute specifies the number of times a frame can be retransmitted by the SVC data link layer before appropriate recovery action is taken.
U32 mscFrNniSigAckTimer	1.3.6.1.4.1.562.36.2.1.70.8.14.1.4	Unsigned32	read-write	This attribute specifies how long the layer 2 protocol waits for an acknowledgment to a sent frame. The value set for ackTimer must be less than the value set for idleProbeTimer.
U32 mscFrNniSigAckDelayTimer	1.3.6.1.4.1.562.36.2.1.70.8.14.1.5	Unsigned32	read-write	This attribute specifies how long the network waits before sending an acknowledgment for a received in-sequence I-frame. A value of 0 means that every frame is acknowledged and there will be no delay in acknowledgment. A non-zero value means that one acknowledgement is sent for a number of frames.
U32 mscFrNniSigIdleProbeTimer	1.3.6.1.4.1.562.36.2.1.70.8.14.1.6	Unsigned32	read-write	This attribute specifies how long the link is permitted to remain idle (that is, no frames are exchanged on the data link). Upon expiry of this timer, the network side's link layer polls its peer for status. The value set for idleProbeTimer must be greater than the value set for ackTimer.
mscFrNniSigCodesTable	1.3.6.1.4.1.562.36.2.1.70.8.15		not-accessible	This group contains the remote data network address, the last SVC clear cause and the last SVC diagnostic code coming from the subnet or the local VC.
mscFrNniSigCodesEntry	1.3.6.1.4.1.562.36.2.1.70.8.15.1		not-accessible	An entry in the mscFrNniSigCodesTable.
STR mscFrNniSigLastClearRemoteDataNetworkAddress	1.3.6.1.4.1.562.36.2.1.70.8.15.1.1	DigitString	read-only	This attribute indicates the Data Network Address (DNA) of the remote (the other end of the SVC connection) of the call which cleared last and whose clear and diagnostic codes were recorded.
U32 mscFrNniSigLastClearCause	1.3.6.1.4.1.562.36.2.1.70.8.15.1.2	Unsigned32	read-only	This attribute indicates the last SVC clear cause signalled at the end of the connection or failure to connect. It is updated only if the clear request comes from the subnet or the call is rejected locally by the VC. The same set of possible values provides the clear cause field in the accounting record.
U32 mscFrNniSigLastDiagnosticCode	1.3.6.1.4.1.562.36.2.1.70.8.15.1.3	Unsigned32	read-only	This attribute indicates the last SVC diagnostic code signalled at the end of the connection or failure to connect. It is updated if the clear request comes from the subnet or the call is rejected locally by the VC. The same set of possible values provides the diagnostic code field in the accounting record.
mscFrNniSigStateTable	1.3.6.1.4.1.562.36.2.1.70.8.16		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
mscFrNniSigStateEntry	1.3.6.1.4.1.562.36.2.1.70.8.16.1		not-accessible	An entry in the mscFrNniSigStateTable.
INT mscFrNniSigAdminState	1.3.6.1.4.1.562.36.2.1.70.8.16.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT mscFrNniSigOperationalState	1.3.6.1.4.1.562.36.2.1.70.8.16.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT mscFrNniSigUsageState	1.3.6.1.4.1.562.36.2.1.70.8.16.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
mscFrNniSigStatsTable	1.3.6.1.4.1.562.36.2.1.70.8.17		not-accessible	This group contains the statistics related to the SVC signaling layer at the interface level.
mscFrNniSigStatsEntry	1.3.6.1.4.1.562.36.2.1.70.8.17.1		not-accessible	An entry in the mscFrNniSigStatsTable.
G32 mscFrNniSigCurrentNumberOfSvcCalls	1.3.6.1.4.1.562.36.2.1.70.8.17.1.1	Gauge32	read-only	This attribute indicates the number of Frame Relay SVCs currently existing on this interface.
G32 mscFrNniSigInCalls	1.3.6.1.4.1.562.36.2.1.70.8.17.1.2	Gauge32	read-only	This attribute indicates the current number of incoming SVCs on this interface (that is, the number of SVCs for which this interface represents the destination end of the call).
C32 mscFrNniSigInCallsRefused	1.3.6.1.4.1.562.36.2.1.70.8.17.1.3	Counter32	read-only	This attribute counts the incoming SVC call requests that are rejected by either this interface or by the called user. When this count exceeds the maximum, it wraps to zero.
G32 mscFrNniSigOutCalls	1.3.6.1.4.1.562.36.2.1.70.8.17.1.4	Gauge32	read-only	This attribute indicates the current number of outgoing SVCs on this interface (that is, the number of SVCs for which this interface represents the source end of the call).
C32 mscFrNniSigOutCallsFailed	1.3.6.1.4.1.562.36.2.1.70.8.17.1.5	Counter32	read-only	This attribute counts the outgoing SVC call requests that are rejected by either this interface, or by the network side of the destination end, or by the called user. When this count exceeds the maximum, it wraps to zero.
C32 mscFrNniSigProtocolErrors	1.3.6.1.4.1.562.36.2.1.70.8.17.1.6	Counter32	read-only	This attribute counts the number of times a FRF.10 protocol error has occurred. Any one of the following events constitutes a protocol error: 1. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir, Bc and Be are all zero; 2. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, Cir is zero but Bc is non-zero, or Bc is zero but Cir is non-zero; 3. In the user-signaled Link Layer Core Parameters IE within the SETUP or CONNECT messages, the Minimum Acceptable CIR is greater than Cir; 4. At the destination end, any of the destination to source direction link layer core parameters has been increased in the CONNECT message from the called user; 5. At the destination end, the destination to source direction Cir in the CONNECT message is smaller than the corresponding minimum acceptable Cir signaled to the called user; 6. At the source end, any of the source to destination direction link layer core parameters in the CONNECT message from the destination end has been increased; 7. At the source end, the source to destination direction Cir, after negotiation, is smaller than the corresponding minimum acceptable Cir; 8. The network has received a STATUS message from the user with an incompatible FRF.10 state. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigQualityOfServiceNotAvailable	1.3.6.1.4.1.562.36.2.1.70.8.17.1.7	Counter32	read-only	This attribute counts the number of incoming and outgoing SVCs that are rejected because the quality of service requested cannot be met by the network. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigSetupTimeout	1.3.6.1.4.1.562.36.2.1.70.8.17.1.8	Counter32	read-only	This attribute counts the number of times the T303 setup timer has expired. When this count reaches maximum, it wraps to zero.
U32 mscFrNniSigLastCauseInStatusMsgReceived	1.3.6.1.4.1.562.36.2.1.70.8.17.1.9	Unsigned32	read-only	This attribute indicates the cause value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is 0 which means that no STATUS message has been received for an existing call yet.
INT mscFrNniSigLastStateInStatusMsgReceived	1.3.6.1.4.1.562.36.2.1.70.8.17.1.10	INTEGER	read-only	This attribute indicates the state value in the last received user's STATUS message to an existing call. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
U32 mscFrNniSigLastDlciReceivedStatus	1.3.6.1.4.1.562.36.2.1.70.8.17.1.11	Unsigned32	read-only	This attribute shows the value of the DLCI that has most recently received a STATUS message from the user. The initial value of this attribute is 0.
INT mscFrNniSigLastStateReceivedStatus	1.3.6.1.4.1.562.36.2.1.70.8.17.1.12	INTEGER	read-only	This attribute shows the network FRF.10 state of the DLCI that has most recently received a STATUS message from the user. The DLCI to which this STATUS message applies is specified in the lastDlciReceivedStatus attribute. The initial value of this attribute is notApplicable.
C32 mscFrNniSigDlciCollisions	1.3.6.1.4.1.562.36.2.1.70.8.17.1.15	Counter32	read-only	This attribute counts the number of call failures due to DLCI collisions.
mscFrNniSigLapfStatusTable	1.3.6.1.4.1.562.36.2.1.70.8.18		not-accessible	This group contains the Q.922 SVC data link layer status.
mscFrNniSigLapfStatusEntry	1.3.6.1.4.1.562.36.2.1.70.8.18.1		not-accessible	An entry in the mscFrNniSigLapfStatusTable.
INT mscFrNniSigCurrentState	1.3.6.1.4.1.562.36.2.1.70.8.18.1.1	INTEGER	read-only	This attribute shows the current state of the SVC data link layer interface.
INT mscFrNniSigLastStateChangeReason	1.3.6.1.4.1.562.36.2.1.70.8.18.1.2	INTEGER	read-only	This attribute shows the reason for the most recent state change. notStarted - this is the default state after SVC data link has just been created. abmeEntered - SVC data link has entered Asynchronous Balanced Mode after SABME or UA has been received. abmeReset - the data link has been reset. dmReceived - DM response received. dmSent - DM sent. discReceived - DISC response received. discSent - DISC sent. frmrReceived - FRMR received. n200RetranTimeOut - retransmitLimit has been exceeded. other - unspecified state change reasons. The most likely reason for this is the transition from state waitingAck to state informationTransfer.
STR mscFrNniSigFrmrReceive	1.3.6.1.4.1.562.36.2.1.70.8.18.1.3	HexString	read-only	This attribute shows the information field of the Frame Reject (FRMR) most recently received.
C32 mscFrNniSigCurrentQueueSize	1.3.6.1.4.1.562.36.2.1.70.8.18.1.4	Counter32	read-only	This attribute shows the current number of frames in the SVC data link layer transmit queue.
mscFrNniSigLapfStatsTable	1.3.6.1.4.1.562.36.2.1.70.8.19		not-accessible	This group contains the statistics for the SVC data link layer.
mscFrNniSigLapfStatsEntry	1.3.6.1.4.1.562.36.2.1.70.8.19.1		not-accessible	An entry in the mscFrNniSigLapfStatsTable.
C32 mscFrNniSigRemoteBusy	1.3.6.1.4.1.562.36.2.1.70.8.19.1.2	Counter32	read-only	This attribute counts the number of times transmission of an I-frame was unsuccessful due to a perceived remote busy condition (window closed or remote busy). When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigReceiveRejectFrame	1.3.6.1.4.1.562.36.2.1.70.8.19.1.3	Counter32	read-only	This attribute counts the number of REJ frames received by the interface. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigAckTimeout	1.3.6.1.4.1.562.36.2.1.70.8.19.1.4	Counter32	read-only	This attribute counts the number of times the ackTimer has expired. Frequent increments of this counter indicate a problem at the link or improper values have been chosen for ackTimer and ackDelayTimer between the local and remote sides. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigIFramesTransmitted	1.3.6.1.4.1.562.36.2.1.70.8.19.1.5	Counter32	read-only	This attribute counts the number of SVC I-frames transmitted to the interface on DLCI 0. An I-frame may be counted more than once if there are retransmissions at the SVC data link layer. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigIFramesTxDiscarded	1.3.6.1.4.1.562.36.2.1.70.8.19.1.6	Counter32	read-only	This attribute counts the number of SVC I-frames that are bound for the link but have been discarded. Discard reasons may be one of the following: 1. the frame length is beyond the allowed limit. 2. the SVC data link layer is in disconnected state. 3. the transmit queue has been purged because the queue length has reached the reset threshold. 4. the transmit queue or the queue waiting for acknowledgment has been purged because the link cannot be re-established. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigIFramesReceived	1.3.6.1.4.1.562.36.2.1.70.8.19.1.7	Counter32	read-only	This attribute counts the number of SVC I-frames received from the interface. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigIFramesRcvdDiscarded	1.3.6.1.4.1.562.36.2.1.70.8.19.1.8	Counter32	read-only	This attribute counts the number of SVC I-frames received but have been discarded. The discard reasons are: 1. incorrect frame size 2. frame is out of sequence 3. frame received while the network side of the SVC data link layer is not in the informationTransfer or waitingAck state. When this count reaches maximum, it wraps to zero.
C32 mscFrNniSigStateChange	1.3.6.1.4.1.562.36.2.1.70.8.19.1.8650	Counter32	read-only	This attribute counts the number of times the SVC data link layer interface has changed state. While the data link layer is in informationTransfer state, this counter will increment on each expiry of idleProbeTimer as its state goes from informationTransfer to waitingAck and back. When this count exceeds the maximum, it wraps to zero.
mscFrNniSigSvcaccTable	1.3.6.1.4.1.562.36.2.1.70.8.20		not-accessible	This group contains the provisionable attribute which controls accounting for this interface.
mscFrNniSigSvcaccEntry	1.3.6.1.4.1.562.36.2.1.70.8.20.1		not-accessible	An entry in the mscFrNniSigSvcaccTable.
INT mscFrNniSigDefaultAccounting	1.3.6.1.4.1.562.36.2.1.70.8.20.1.1	INTEGER	read-write	This attribute specifies whether accounting data collection and record generation is turned on for switched connections at this interface. For accounting data collection and record generation to occur, this attribute must be on and at least one of the accountCollection reasons in the Dna component must be present.
mscFrNniSigBandwidthNotAvailableTable	1.3.6.1.4.1.562.36.2.1.70.8.672		not-accessible	This attribute counts the number of call failures for each bandwidth pool due to the requested bandwidth not being available.
mscFrNniSigBandwidthNotAvailableEntry	1.3.6.1.4.1.562.36.2.1.70.8.672.1		not-accessible	An entry in the mscFrNniSigBandwidthNotAvailableTable.
I32 mscFrNniSigBandwidthNotAvailableIndex	1.3.6.1.4.1.562.36.2.1.70.8.672.1.1	Integer32	not-accessible	This variable represents the mscFrNniSigBandwidthNotAvailableTable specific index for the mscFrNniSigBandwidthNotAvailableTable.
C32 mscFrNniSigBandwidthNotAvailableValue	1.3.6.1.4.1.562.36.2.1.70.8.672.1.2	Counter32	read-only	This variable represents an individual value for the mscFrNniSigBandwidthNotAvailableTable.
mscFrNniLts	1.3.6.1.4.1.562.36.2.1.70.9
mscFrNniLtsRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.9.1		not-accessible	This entry controls the addition and deletion of mscFrNniLts components.
mscFrNniLtsRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.9.1.1		not-accessible	A single entry in the table represents a single mscFrNniLts component.
ROW mscFrNniLtsRowStatus	1.3.6.1.4.1.562.36.2.1.70.9.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniLts components. These components can be added and deleted.
STR mscFrNniLtsComponentName	1.3.6.1.4.1.562.36.2.1.70.9.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniLtsStorageType	1.3.6.1.4.1.562.36.2.1.70.9.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniLts tables.
NON mscFrNniLtsIndex	1.3.6.1.4.1.562.36.2.1.70.9.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniLts tables.
mscFrNniLtsPat	1.3.6.1.4.1.562.36.2.1.70.9.2
mscFrNniLtsPatRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.9.2.1		not-accessible	This entry controls the addition and deletion of mscFrNniLtsPat components.
mscFrNniLtsPatRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.9.2.1.1		not-accessible	A single entry in the table represents a single mscFrNniLtsPat component.
ROW mscFrNniLtsPatRowStatus	1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniLtsPat components. These components can be added and deleted.
STR mscFrNniLtsPatComponentName	1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniLtsPatStorageType	1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniLtsPat tables.
I32 mscFrNniLtsPatIndex	1.3.6.1.4.1.562.36.2.1.70.9.2.1.1.10	Integer32	not-accessible	This variable represents the index for the mscFrNniLtsPat tables.
mscFrNniLtsPatDefaultsTable	1.3.6.1.4.1.562.36.2.1.70.9.2.10		not-accessible	This attribute group contains the specifications of the pattern.
mscFrNniLtsPatDefaultsEntry	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1		not-accessible	An entry in the mscFrNniLtsPatDefaultsTable.
U32 mscFrNniLtsPatDefaultDlci	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.200	Unsigned32	read-write	This attribute specifies for which dlci (on the local end) the frames are destined.
U32 mscFrNniLtsPatDefaultNumFrames	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.201	Unsigned32	read-write	This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
U32 mscFrNniLtsPatDefaultDataSize	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.202	Unsigned32	read-write	This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
OCT mscFrNniLtsPatDefaultHeaderBits	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.203	OCTET STRING	read-write	This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
U32 mscFrNniLtsPatDefaultHeaderLength	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.204	Unsigned32	read-write	This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header.
HEX mscFrNniLtsPatDefaultEABits	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.205	Hex	read-write	This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate EABits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect EABits in the header.
STR mscFrNniLtsPatDefaultPayloadPattern	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.206	HexString	read-write	This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
INT mscFrNniLtsPatDefaultRfc1490Header	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.207	INTEGER	read-write	This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
INT mscFrNniLtsPatDefaultUseBadLrc	1.3.6.1.4.1.562.36.2.1.70.9.2.10.1.208	INTEGER	read-write	This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
mscFrNniLtsPatSetupTable	1.3.6.1.4.1.562.36.2.1.70.9.2.11		not-accessible	This attribute group contains the specifications of the pattern.
mscFrNniLtsPatSetupEntry	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1		not-accessible	An entry in the mscFrNniLtsPatSetupTable.
U32 mscFrNniLtsPatDlci	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.200	Unsigned32	read-write	This attribute specifies for which dlci (on the local end) the frames are destined.
U32 mscFrNniLtsPatNumFrames	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.201	Unsigned32	read-write	This attribute specifies the number of frames in this pattern. This is the number of frames of this type which will be generated in one timeInterval.
U32 mscFrNniLtsPatDataSize	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.202	Unsigned32	read-write	This attribute specifies the payload size of each frame in bytes. This is in excess to the header.
OCT mscFrNniLtsPatHeaderBits	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.203	OCTET STRING	read-write	This attribute specifies whether the following bits are on/off in the header of each frame. The following bits can be set: BeCn, C/R, De, FeCn Description of bits: becn(0) fecn(1) cr(2) de(3)
U32 mscFrNniLtsPatHeaderLength	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.204	Unsigned32	read-write	This attribute specifies the size of the frame relay header in bytes. Passport currently only supports a 2-byte header. Valid values are 0, 2, 3, 4. 0 indicates to use no header. That is, the frame will start with either the payload or rfc1490 header.
HEX mscFrNniLtsPatEaBits	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.205	Hex	read-write	This attribute specifies how the address field extension bits are set in the frame header. Consider the value to be a four bit binary number. For example, 4 = 0100. Only the first headerLength bits are used. For instance, suppose headerLength is 3, then the appropriate eaBits is 2, or 0010. This attribute can be used to create a header of length greater than two bytes or to specify incorrect eaBits in the header.
STR mscFrNniLtsPatPayloadPattern	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.206	HexString	read-write	This attribute specifies the payload of each frame. The value specified is in hexadecimal, where every two digits represent a byte. A maximum of 24 digits (12 bytes) may be set, after which the pattern will repeat in the payload (depending on repeatPattern attribute). NOTE: If a RFC 1490 header is specified, via the 1490Header attribute, the specified pattern will begin following the header (i.e. at the 9th byte in the payload).
INT mscFrNniLtsPatRfc1490Header	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.207	INTEGER	read-write	This attribute specifies the appropriate RFC 1490 encapsulated header of the frame. A value of 0 indicates no 1490 header. NOTE: This header resides in the first 8 bytes of the payload. If the specified value is non-zero, then the payload pattern provisioned will begin at the 9th byte.
INT mscFrNniLtsPatUseBadLrc	1.3.6.1.4.1.562.36.2.1.70.9.2.11.1.208	INTEGER	read-write	This attribute specifies whether the frames from this pattern are to have a bad LRC prior to being sent to the framer. The LRC is checked while the frame is being put onto the link and the failure should cause an abort frame to be sent.
mscFrNniLtsPatOpDataTable	1.3.6.1.4.1.562.36.2.1.70.9.2.12		not-accessible	This group contains the operational attributes which allow changing the pattern outside of provisioning mode.
mscFrNniLtsPatOpDataEntry	1.3.6.1.4.1.562.36.2.1.70.9.2.12.1		not-accessible	An entry in the mscFrNniLtsPatOpDataTable.
STR mscFrNniLtsPatFramePattern	1.3.6.1.4.1.562.36.2.1.70.9.2.12.1.200	HexString	read-only	This attribute displays the first 20 to 24 bytes of the frame payload, depending on the frame relay header size selected. This attribute represents the frame if it were at least 20 to 24 bytes in size. That is, the actual frame may be smaller.
U32 mscFrNniLtsPatHdlcBitsInserted	1.3.6.1.4.1.562.36.2.1.70.9.2.12.1.201	Unsigned32	read-only	This attribute displays how many times a zero bit will be inserted after 5 consecutive 1 bits when a frame from this pattern is sent out.
mscFrNniLtsPatOpStateTable	1.3.6.1.4.1.562.36.2.1.70.9.2.13		not-accessible	This group contains the attributes containing the operational statistics of the pattern.
mscFrNniLtsPatOpStateEntry	1.3.6.1.4.1.562.36.2.1.70.9.2.13.1		not-accessible	An entry in the mscFrNniLtsPatOpStateTable.
NUM mscFrNniLtsPatLoad	1.3.6.1.4.1.562.36.2.1.70.9.2.13.1.200	FixedPoint3	read-only	This attribute indicates the load due to this particular pattern. The loads associated with all of the provisioned patterns are summed to arrive at the FrLts load.
INT mscFrNniLtsPatStatus	1.3.6.1.4.1.562.36.2.1.70.9.2.13.1.201	INTEGER	read-write	This attributes specifies the administrative state of the pattern. A disabled pattern will not be generated, although it can still be triggered.
mscFrNniLtsSetupTable	1.3.6.1.4.1.562.36.2.1.70.9.10		not-accessible	This attribute group contains the parameters used to configure the behavior of the Frame Relay Load Test System.
mscFrNniLtsSetupEntry	1.3.6.1.4.1.562.36.2.1.70.9.10.1		not-accessible	An entry in the mscFrNniLtsSetupTable.
U32 mscFrNniLtsDuration	1.3.6.1.4.1.562.36.2.1.70.9.10.1.200	Unsigned32	read-write	This attribute specifies the duration of the test in milliseconds. The test will run until the duration expires or the STOP command is issued. A value of 0 is used to indicate infinity.
INT mscFrNniLtsAlgorithm	1.3.6.1.4.1.562.36.2.1.70.9.10.1.201	INTEGER	read-write	This attribute specifies which algorithm is used to generate the frames. ContinuousBurst This mode of traffic generation creates traffic at the maximum rate possible until all of the frames have been sent. The generator then waits until the end of the timeInterval to begin again. IntervalBurst This algorithm attempts to generate 10 ms bursts of burstSize frames. It will generate as many of the burstSize frames as it can per sub-interval. DelayedBurst This algorithm generates bursts of burstSize frames separated by 10 ms delays. FixedBurst This aglorithm is similar to IntervalBurst, except a fixed burst size of 12 frames is used. delayMeasurement This algorithm is used to measure delay. The specified number of frames in the indicated pattern are generated, one at a time, with a maximum wait of maxDelay before sending the next frame. This algorithm is not implemented yet.
U32 mscFrNniLtsBurstSize	1.3.6.1.4.1.562.36.2.1.70.9.10.1.204	Unsigned32	read-write	This attribute specifies the number of frames per burst under the delayedBurst and intervalBurst algorithms.
U32 mscFrNniLtsTimeInterval	1.3.6.1.4.1.562.36.2.1.70.9.10.1.205	Unsigned32	read-write	This attribute specifies the time interval to the specified number of seconds. Granuality is in centiseconds. Maximum is 1 minute.
mscFrNniLtsStateTable	1.3.6.1.4.1.562.36.2.1.70.9.11		not-accessible	This group contains the operation statistics of the load generator.
mscFrNniLtsStateEntry	1.3.6.1.4.1.562.36.2.1.70.9.11.1		not-accessible	An entry in the mscFrNniLtsStateTable.
INT mscFrNniLtsGeneratorState	1.3.6.1.4.1.562.36.2.1.70.9.11.1.200	INTEGER	read-only	This attribute indicates whether the Lts is generating traffic.
INT mscFrNniLtsCycleIncomplete	1.3.6.1.4.1.562.36.2.1.70.9.11.1.201	INTEGER	read-only	This attribute indicates whether the time required to generate all of the enabled patterns is more than timeInterval by a true value. Otherwise, this flag is set to false. Default is True.
U32 mscFrNniLtsLastActiveInterval	1.3.6.1.4.1.562.36.2.1.70.9.11.1.202	Unsigned32	read-only	This attribute indicates the actual time it took to generate all of the enabled patterns in the last cycle. If cycleIncomplete is true, this value should be zero.
NUM mscFrNniLtsLoad	1.3.6.1.4.1.562.36.2.1.70.9.11.1.204	FixedPoint3	read-only	This attribute indicates the load being generated. This value represents that calculated using the set number of ticks. The actual burstTimeInterval may differ. One entire cycle of the patterns is completed in activeInterval and thus most of the load may be concentrated early in the set interval.
U32 mscFrNniLtsElapsedGenerationTime	1.3.6.1.4.1.562.36.2.1.70.9.11.1.205	Unsigned32	read-only	This attribute indicates how many milliseconds have elapsed since the start of this test.
mscFrNniLtsResultsTable	1.3.6.1.4.1.562.36.2.1.70.9.12		not-accessible	This group contains the frame counting attributes for the LTS component.
mscFrNniLtsResultsEntry	1.3.6.1.4.1.562.36.2.1.70.9.12.1		not-accessible	An entry in the mscFrNniLtsResultsTable.
C32 mscFrNniLtsFramesTx	1.3.6.1.4.1.562.36.2.1.70.9.12.1.200	Counter32	read-only	This attribute specifies the number of frames send to the network since the last time these statistics were cleared. This is similar to the framesToIf attribute of the FRAMER component.
U32 mscFrNniLtsBytesTx	1.3.6.1.4.1.562.36.2.1.70.9.12.1.204	Unsigned32	read-only	This attribute indicates the number of bytes sent.
NUM mscFrNniLtsBitRateTx	1.3.6.1.4.1.562.36.2.1.70.9.12.1.208	FixedPoint3	read-only	This attribute indicates the bit rate being sent to the link. It should only differ from the load if the burstTimeInterval would be >= the timeInterval or burstSize frames cannot be generated in 10ms (intervalBurst algorithm).
U32 mscFrNniLtsFrameRateTx	1.3.6.1.4.1.562.36.2.1.70.9.12.1.209	Unsigned32	read-only	This attribute indicates the frame rate being sent to the link. It is calculated using the number of frames sent to the link in one cycle of the patterns.
mscFrNniCidDataTable	1.3.6.1.4.1.562.36.2.1.70.10		not-accessible	This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
mscFrNniCidDataEntry	1.3.6.1.4.1.562.36.2.1.70.10.1		not-accessible	An entry in the mscFrNniCidDataTable.
U32 mscFrNniCustomerIdentifier	1.3.6.1.4.1.562.36.2.1.70.10.1.1	Unsigned32	read-write	This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
mscFrNniStateTable	1.3.6.1.4.1.562.36.2.1.70.11		not-accessible	This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
mscFrNniStateEntry	1.3.6.1.4.1.562.36.2.1.70.11.1		not-accessible	An entry in the mscFrNniStateTable.
INT mscFrNniAdminState	1.3.6.1.4.1.562.36.2.1.70.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
INT mscFrNniOperationalState	1.3.6.1.4.1.562.36.2.1.70.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
INT mscFrNniUsageState	1.3.6.1.4.1.562.36.2.1.70.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OCT mscFrNniAvailabilityStatus	1.3.6.1.4.1.562.36.2.1.70.11.1.4	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OCT mscFrNniProceduralStatus	1.3.6.1.4.1.562.36.2.1.70.11.1.5	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OCT mscFrNniControlStatus	1.3.6.1.4.1.562.36.2.1.70.11.1.6	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OCT mscFrNniAlarmStatus	1.3.6.1.4.1.562.36.2.1.70.11.1.7	OCTET STRING	read-only	If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
INT mscFrNniStandbyStatus	1.3.6.1.4.1.562.36.2.1.70.11.1.8	INTEGER	read-only	If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
INT mscFrNniUnknownStatus	1.3.6.1.4.1.562.36.2.1.70.11.1.9	INTEGER	read-only	This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
mscFrNniStatsTable	1.3.6.1.4.1.562.36.2.1.70.12		not-accessible	This group contains the statistics about the operational behaviour of the service at the interface level.
mscFrNniStatsEntry	1.3.6.1.4.1.562.36.2.1.70.12.1		not-accessible	An entry in the mscFrNniStatsTable.
U32 mscFrNniLastUnknownDlci	1.3.6.1.4.1.562.36.2.1.70.12.1.1	Unsigned32	read-only	This attribute identifies the most recent DLCI which user frames were received on for which a DLCI has not been provisioned on the port.
C32 mscFrNniUnknownDlciFramesFromIf	1.3.6.1.4.1.562.36.2.1.70.12.1.2	Counter32	read-only	This attribute contains a count of the number of frames received from the interface with an unknown DLCI (DLCI which is not provisioned). When the maximum is exceeded the count wraps to zero.
C32 mscFrNniInvalidHeaderFramesFromIf	1.3.6.1.4.1.562.36.2.1.70.12.1.3	Counter32	read-only	This attribute counts the number of frames received from the interface with an invalid header format. When the maximum is exceeded the count wraps to zero.
mscFrNniIfEntryTable	1.3.6.1.4.1.562.36.2.1.70.13		not-accessible	This group contains the provisionable attributes for the ifEntry.
mscFrNniIfEntryEntry	1.3.6.1.4.1.562.36.2.1.70.13.1		not-accessible	An entry in the mscFrNniIfEntryTable.
INT mscFrNniIfAdminStatus	1.3.6.1.4.1.562.36.2.1.70.13.1.1	INTEGER	read-write	The desired state of the interface. The up state indicates the interface is operational. The down state indicates the interface is not operational. The testing state indicates that no operational packets can be passed.
NUM mscFrNniIfIndex	1.3.6.1.4.1.562.36.2.1.70.13.1.2	InterfaceIndex	read-only	This is the index for the IfEntry. Its value is automatically initialized during the provisioning process.
mscFrNniOperStatusTable	1.3.6.1.4.1.562.36.2.1.70.14		not-accessible	This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
mscFrNniOperStatusEntry	1.3.6.1.4.1.562.36.2.1.70.14.1		not-accessible	An entry in the mscFrNniOperStatusTable.
INT mscFrNniSnmpOperStatus	1.3.6.1.4.1.562.36.2.1.70.14.1.1	INTEGER	read-only	The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
mscFrNniEmissionPriorityQsTable	1.3.6.1.4.1.562.36.2.1.70.15		not-accessible	This group contains the provisionable attribute to specifie the number of Frame Relay egress emission priority queues to be used on that Frame Relay Interface
mscFrNniEmissionPriorityQsEntry	1.3.6.1.4.1.562.36.2.1.70.15.1		not-accessible	An entry in the mscFrNniEmissionPriorityQsTable.
U32 mscFrNniNumberOfEmissionQs	1.3.6.1.4.1.562.36.2.1.70.15.1.1	Unsigned32	read-write	This attribute specifies the number of egress emission priority queues that will be used for that Frame Relay interface. The possible values of this attribute are 2 or 4: For V.35, V.11, HSSI, E1, DS1, E3, DS3 or 8pDS1 the possible values are: 2 (in which case they are hardware queues), or 4 (in which case they are software queues). For DS1C, E1C or DS3C the possible values are 2, 4 (in all cases they are software queues).
mscFrNniCa	1.3.6.1.4.1.562.36.2.1.70.101
mscFrNniCaRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.101.1		not-accessible	This entry controls the addition and deletion of mscFrNniCa components.
mscFrNniCaRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.101.1.1		not-accessible	A single entry in the table represents a single mscFrNniCa component.
ROW mscFrNniCaRowStatus	1.3.6.1.4.1.562.36.2.1.70.101.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of mscFrNniCa components. These components cannot be added nor deleted.
STR mscFrNniCaComponentName	1.3.6.1.4.1.562.36.2.1.70.101.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniCaStorageType	1.3.6.1.4.1.562.36.2.1.70.101.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniCa tables.
NON mscFrNniCaIndex	1.3.6.1.4.1.562.36.2.1.70.101.1.1.10	NonReplicated	not-accessible	This variable represents the index for the mscFrNniCa tables.
mscFrNniCaTpm	1.3.6.1.4.1.562.36.2.1.70.101.2
mscFrNniCaTpmRowStatusTable	1.3.6.1.4.1.562.36.2.1.70.101.2.1		not-accessible	This entry controls the addition and deletion of mscFrNniCaTpm components.
mscFrNniCaTpmRowStatusEntry	1.3.6.1.4.1.562.36.2.1.70.101.2.1.1		not-accessible	A single entry in the table represents a single mscFrNniCaTpm component.
ROW mscFrNniCaTpmRowStatus	1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of mscFrNniCaTpm components. These components can be added and deleted.
STR mscFrNniCaTpmComponentName	1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO mscFrNniCaTpmStorageType	1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the mscFrNniCaTpm tables.
I32 mscFrNniCaTpmIndex	1.3.6.1.4.1.562.36.2.1.70.101.2.1.1.10	Integer32	not-accessible	This variable represents the index for the mscFrNniCaTpm tables.
mscFrNniCaTpmProvTable	1.3.6.1.4.1.562.36.2.1.70.101.2.10		not-accessible	This attribute group contains the provisionable attributes of the Tpm component at this interface.
mscFrNniCaTpmProvEntry	1.3.6.1.4.1.562.36.2.1.70.101.2.10.1		not-accessible	An entry in the mscFrNniCaTpmProvTable.
U32 mscFrNniCaTpmAssignedIngressBandwidthPool	1.3.6.1.4.1.562.36.2.1.70.101.2.10.1.2	Unsigned32	read-write	This attribute specifies the ingress bandwidth pool which is used to support this transfer priority at this interface. When this attribute is set to sameAsModule, the bandwidth pool that is used is obtained from the assignedIngressBandwidthPool attribute under the Mod Frs DprsNet Tpm/n component. VALUES ( 16 = sameAsModule )
U32 mscFrNniCaTpmAssignedEgressBandwidthPool	1.3.6.1.4.1.562.36.2.1.70.101.2.10.1.3	Unsigned32	read-write	This attribute specifies the egress bandwidth pool which is used to support this transfer priority at this interface. When this attribute is set to sameAsModule, the bandwidth pool that is used is obtained from the assignedEgressBandwidthPool attribute under the Mod Frs DprsNet Tpm/n component. VALUES ( 16 = sameAsModule )
mscFrNniCaProvTable	1.3.6.1.4.1.562.36.2.1.70.101.10		not-accessible	This attribute group contains the common provisionable attributes of the Ca component.
mscFrNniCaProvEntry	1.3.6.1.4.1.562.36.2.1.70.101.10.1		not-accessible	An entry in the mscFrNniCaProvTable.
U32 mscFrNniCaOverrideLinkRate	1.3.6.1.4.1.562.36.2.1.70.101.10.1.2	Unsigned32	read-write	This attribute allows the link rate to be overridden for this interface. This allows the user to specify a value other than the actual physical link rate computed when a Framer component is provisioned. When a VFramer component is provisioned, this attribute overrides a link rate set to the maximum value supported by CAC . This attribute serves to provide the user control on the amount of bandwidth available for performing CAC.
U32 mscFrNniCaMaximumBandwidthPerCall	1.3.6.1.4.1.562.36.2.1.70.101.10.1.3	Unsigned32	read-write	This attribute specifies the maximum bandwidth that can be allocated per connection.
mscFrNniCaIngressCacTable	1.3.6.1.4.1.562.36.2.1.70.101.11		not-accessible	This attribute group contains the common provisionable attributes for ingress call admission control.
mscFrNniCaIngressCacEntry	1.3.6.1.4.1.562.36.2.1.70.101.11.1		not-accessible	An entry in the mscFrNniCaIngressCacTable.
INT mscFrNniCaIngressApplyToCos	1.3.6.1.4.1.562.36.2.1.70.101.11.1.2	INTEGER	read-write	This attribute specifies which Classes of Service (CoS) have ingress Call Admission Control (CAC) applied to them. Ingress CAC applies only to swithced connections (SVCs and S-SPVCs). none - Ingress CAC is turned off for all classes of service. cirOnly - Ingress CAC is applied only to the CIR portion of a connection's bandwidth requirements for CIR>0 classes of service. cirAndEir - Ingress CAC is applied to both CIR and EIR portions of a connections bandwidth requirements for all classes of service.
U32 mscFrNniCaIngressMaximumEirOnlyCalls	1.3.6.1.4.1.562.36.2.1.70.101.11.1.4	Unsigned32	read-write	This attribute specifies the maximum number of connections in the ingress direction with EIR only traffic that can be up at a given time.
mscFrNniCaEgressCacTable	1.3.6.1.4.1.562.36.2.1.70.101.12		not-accessible	This attribute group contains the common provisionable attributes for egress call admission control.
mscFrNniCaEgressCacEntry	1.3.6.1.4.1.562.36.2.1.70.101.12.1		not-accessible	An entry in the mscFrNniCaEgressCacTable.
INT mscFrNniCaEgressApplyToCos	1.3.6.1.4.1.562.36.2.1.70.101.12.1.2	INTEGER	read-write	This attribute specifies which Classes of Service (CoS) have egress Call Admission Control (CAC) applied to them. Egress CAC applies only to swithced connections (SVCs and S-SPVCs). none - Egress CAC is turned off for all classes of service. cirOnly - Egress CAC is applied only to the CIR portion of a connection's bandwidth requirements for CIR>0 classes of service. cirAndEir - Egress CAC is applied to both CIR and EIR portions of a connections bandwidth requirements for all classes of service.
U32 mscFrNniCaEgressMaximumEirOnlyCalls	1.3.6.1.4.1.562.36.2.1.70.101.12.1.4	Unsigned32	read-write	This attribute specifies the maximum number of connections in the egress direction with EIR only traffic that can be up at a given time.
mscFrNniCaOpTable	1.3.6.1.4.1.562.36.2.1.70.101.13		not-accessible	This attribute group contains the operational status of the Ca component.
mscFrNniCaOpEntry	1.3.6.1.4.1.562.36.2.1.70.101.13.1		not-accessible	An entry in the mscFrNniCaOpTable.
U32 mscFrNniCaLinkRate	1.3.6.1.4.1.562.36.2.1.70.101.13.1.2	Unsigned32	read-only	This attribute indicates the link rate used by both ingress and egress CAC to calculate the effective bandwidth pool sizes. If the provisionable attribute overrideLinkRate under this component is 0, then the link rate reported is the actual link rate of the port or channel. Otherwise, the link rate reported is the overrideLinkRate under this component.
G32 mscFrNniCaNumberRejectedEgressCirPermConn	1.3.6.1.4.1.562.36.2.1.70.101.13.1.681	Gauge32	read-only	This attribute indicates the number of permanent connections (that is, PVC and P-SPVC) that are rejected by egress CAC. A connection is rejected by egress CAC if it requests more egress CIR bandwidth than is available, and the egressApplyToCos attribute is set to either cirOnly or cirAndEir.
G32 mscFrNniCaNumberRejectedEgressEirPermConn	1.3.6.1.4.1.562.36.2.1.70.101.13.1.682	Gauge32	read-only	This attribute indicates the number of permanent connections (that is, PVC and P-SPVC) that are rejected by egress CAC. A connection is rejected by egress CAC if it requests more egress EIR bandwidth than is available, and the egressApplyToCos attribute is set to cirAndEir.
mscFrNniCaIngCirBPTable	1.3.6.1.4.1.562.36.2.1.70.101.666		not-accessible	Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the ingress CIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
mscFrNniCaIngCirBPEntry	1.3.6.1.4.1.562.36.2.1.70.101.666.1		not-accessible	An entry in the mscFrNniCaIngCirBPTable.
I32 mscFrNniCaIngCirBPIndex	1.3.6.1.4.1.562.36.2.1.70.101.666.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaIngCirBPTable specific index for the mscFrNniCaIngCirBPTable.
U32 mscFrNniCaIngCirBPValue	1.3.6.1.4.1.562.36.2.1.70.101.666.1.2	Unsigned32	read-write	This variable represents an individual value for the mscFrNniCaIngCirBPTable.
mscFrNniCaEgCirBpTable	1.3.6.1.4.1.562.36.2.1.70.101.667		not-accessible	Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the egress CIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
mscFrNniCaEgCirBpEntry	1.3.6.1.4.1.562.36.2.1.70.101.667.1		not-accessible	An entry in the mscFrNniCaEgCirBpTable.
I32 mscFrNniCaEgCirBpIndex	1.3.6.1.4.1.562.36.2.1.70.101.667.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaEgCirBpTable specific index for the mscFrNniCaEgCirBpTable.
U32 mscFrNniCaEgCirBpValue	1.3.6.1.4.1.562.36.2.1.70.101.667.1.2	Unsigned32	read-write	This variable represents an individual value for the mscFrNniCaEgCirBpTable.
mscFrNniCaIngCirPoolAdmitBwTable	1.3.6.1.4.1.562.36.2.1.70.101.668		not-accessible	This attribute indicates the total admitted CIR bandwidth from each CIR bandwidth pool in the ingress direction. Each value is the sum of the equivalent bit rates of the admitted connections.
mscFrNniCaIngCirPoolAdmitBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.668.1		not-accessible	An entry in the mscFrNniCaIngCirPoolAdmitBwTable.
I32 mscFrNniCaIngCirPoolAdmitBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.668.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaIngCirPoolAdmitBwTable specific index for the mscFrNniCaIngCirPoolAdmitBwTable.
G32 mscFrNniCaIngCirPoolAdmitBwValue	1.3.6.1.4.1.562.36.2.1.70.101.668.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaIngCirPoolAdmitBwTable.
mscFrNniCaIngCirPoolAvailBwTable	1.3.6.1.4.1.562.36.2.1.70.101.669		not-accessible	This attribute indicates the remaining available CIR bandwidth in each ingress CIR bandwidth pool.
mscFrNniCaIngCirPoolAvailBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.669.1		not-accessible	An entry in the mscFrNniCaIngCirPoolAvailBwTable.
I32 mscFrNniCaIngCirPoolAvailBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.669.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaIngCirPoolAvailBwTable specific index for the mscFrNniCaIngCirPoolAvailBwTable.
G32 mscFrNniCaIngCirPoolAvailBwValue	1.3.6.1.4.1.562.36.2.1.70.101.669.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaIngCirPoolAvailBwTable.
mscFrNniCaEgCirPoolAdmitBwTable	1.3.6.1.4.1.562.36.2.1.70.101.670		not-accessible	This attribute indicates the total admitted CIR bandwidth from each CIR bandwidth pool in the egress direction. Each value is the sum of the equivalent bit rates of the admitted connections.
mscFrNniCaEgCirPoolAdmitBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.670.1		not-accessible	An entry in the mscFrNniCaEgCirPoolAdmitBwTable.
I32 mscFrNniCaEgCirPoolAdmitBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.670.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaEgCirPoolAdmitBwTable specific index for the mscFrNniCaEgCirPoolAdmitBwTable.
G32 mscFrNniCaEgCirPoolAdmitBwValue	1.3.6.1.4.1.562.36.2.1.70.101.670.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaEgCirPoolAdmitBwTable.
mscFrNniCaEgCirPoolAvailBwTable	1.3.6.1.4.1.562.36.2.1.70.101.671		not-accessible	This attribute indicates the remaining available CIR bandwidth in each egress CIR bandwidth pool.
mscFrNniCaEgCirPoolAvailBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.671.1		not-accessible	An entry in the mscFrNniCaEgCirPoolAvailBwTable.
I32 mscFrNniCaEgCirPoolAvailBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.671.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaEgCirPoolAvailBwTable specific index for the mscFrNniCaEgCirPoolAvailBwTable.
G32 mscFrNniCaEgCirPoolAvailBwValue	1.3.6.1.4.1.562.36.2.1.70.101.671.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaEgCirPoolAvailBwTable.
mscFrNniCaIngEirBpTable	1.3.6.1.4.1.562.36.2.1.70.101.673		not-accessible	Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the ingress EIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
mscFrNniCaIngEirBpEntry	1.3.6.1.4.1.562.36.2.1.70.101.673.1		not-accessible	An entry in the mscFrNniCaIngEirBpTable.
I32 mscFrNniCaIngEirBpIndex	1.3.6.1.4.1.562.36.2.1.70.101.673.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaIngEirBpTable specific index for the mscFrNniCaIngEirBpTable.
U32 mscFrNniCaIngEirBpValue	1.3.6.1.4.1.562.36.2.1.70.101.673.1.2	Unsigned32	read-write	This variable represents an individual value for the mscFrNniCaIngEirBpTable.
mscFrNniCaEgEirBpTable	1.3.6.1.4.1.562.36.2.1.70.101.674		not-accessible	Port capacity is partitioned into 16 pools (pool 0 through pool 15) for the egress EIR traffic. This attribute specifies the percentage of port capacity that is allowed for each pool. The percentage for each pool ranges from 0% to 1000% of the link rate. It allows for under or over subscription of the port. Under subscription occurs when the sum of the percentages assigned to the 16 pools is less than 100%. Over subscription occurs when the sum of the percentages for the 16 pools exceeds 100%. The default is full sharing of port capacity with three pre-set partitions.
mscFrNniCaEgEirBpEntry	1.3.6.1.4.1.562.36.2.1.70.101.674.1		not-accessible	An entry in the mscFrNniCaEgEirBpTable.
I32 mscFrNniCaEgEirBpIndex	1.3.6.1.4.1.562.36.2.1.70.101.674.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaEgEirBpTable specific index for the mscFrNniCaEgEirBpTable.
U32 mscFrNniCaEgEirBpValue	1.3.6.1.4.1.562.36.2.1.70.101.674.1.2	Unsigned32	read-write	This variable represents an individual value for the mscFrNniCaEgEirBpTable.
mscFrNniCaIngEirPoolAdmitBwTable	1.3.6.1.4.1.562.36.2.1.70.101.675		not-accessible	This attribute indicates the total admitted EIR bandwidth from each EIR bandwidth pool in the ingress direction. Each value is the sum of the equivalent bit rates of the admitted connections. If the ingressApplyToCos attribute is set to none, all ingress CIR bandwidth pools are set to 0.
mscFrNniCaIngEirPoolAdmitBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.675.1		not-accessible	An entry in the mscFrNniCaIngEirPoolAdmitBwTable.
I32 mscFrNniCaIngEirPoolAdmitBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.675.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaIngEirPoolAdmitBwTable specific index for the mscFrNniCaIngEirPoolAdmitBwTable.
G32 mscFrNniCaIngEirPoolAdmitBwValue	1.3.6.1.4.1.562.36.2.1.70.101.675.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaIngEirPoolAdmitBwTable.
mscFrNniCaIngEirPoolAvailBwTable	1.3.6.1.4.1.562.36.2.1.70.101.676		not-accessible	This attribute indicates the remaining available EIR bandwidth in each ingress EIR bandwidth pool. If the ingressApplyToCos attribute is set to either none or cirOnly, all ingress EIR bandwidth pools are set to 0.
mscFrNniCaIngEirPoolAvailBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.676.1		not-accessible	An entry in the mscFrNniCaIngEirPoolAvailBwTable.
I32 mscFrNniCaIngEirPoolAvailBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.676.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaIngEirPoolAvailBwTable specific index for the mscFrNniCaIngEirPoolAvailBwTable.
G32 mscFrNniCaIngEirPoolAvailBwValue	1.3.6.1.4.1.562.36.2.1.70.101.676.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaIngEirPoolAvailBwTable.
mscFrNniCaEgEirPoolAdmitBwTable	1.3.6.1.4.1.562.36.2.1.70.101.677		not-accessible	This attribute indicates the total admitted EIR bandwidth from each EIR bandwidth pool in the egress direction. Each value is the sum of the equivalent bit rates of the admitted connections. If the egressApplyToCos attribute is set to none, all egress CIR bandwidth pools are set to 0.
mscFrNniCaEgEirPoolAdmitBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.677.1		not-accessible	An entry in the mscFrNniCaEgEirPoolAdmitBwTable.
I32 mscFrNniCaEgEirPoolAdmitBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.677.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaEgEirPoolAdmitBwTable specific index for the mscFrNniCaEgEirPoolAdmitBwTable.
G32 mscFrNniCaEgEirPoolAdmitBwValue	1.3.6.1.4.1.562.36.2.1.70.101.677.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaEgEirPoolAdmitBwTable.
mscFrNniCaEgEirPoolAvailBwTable	1.3.6.1.4.1.562.36.2.1.70.101.678		not-accessible	This attribute indicates the remaining available EIR bandwidth in each egress EIR bandwidth pool. If the egressApplyToCos attribute is set to either none or cirOnly, all egress EIR bandwidth pools are set to 0.
mscFrNniCaEgEirPoolAvailBwEntry	1.3.6.1.4.1.562.36.2.1.70.101.678.1		not-accessible	An entry in the mscFrNniCaEgEirPoolAvailBwTable.
I32 mscFrNniCaEgEirPoolAvailBwIndex	1.3.6.1.4.1.562.36.2.1.70.101.678.1.1	Integer32	not-accessible	This variable represents the mscFrNniCaEgEirPoolAvailBwTable specific index for the mscFrNniCaEgEirPoolAvailBwTable.
G32 mscFrNniCaEgEirPoolAvailBwValue	1.3.6.1.4.1.562.36.2.1.70.101.678.1.2	Gauge32	read-only	This variable represents an individual value for the mscFrNniCaEgEirPoolAvailBwTable.
mscFrNniFrmToIfByQueueTable	1.3.6.1.4.1.562.36.2.1.70.341		not-accessible	This attribute counts the total number of frames transmitted to the interface per egress emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority. The queue values are only indicated when the numberOfEmissionQs is set to 4 queues.
mscFrNniFrmToIfByQueueEntry	1.3.6.1.4.1.562.36.2.1.70.341.1		not-accessible	An entry in the mscFrNniFrmToIfByQueueTable.
I32 mscFrNniFrmToIfByQueueIndex	1.3.6.1.4.1.562.36.2.1.70.341.1.1	Integer32	not-accessible	This variable represents the index for the mscFrNniFrmToIfByQueueTable.
U32 mscFrNniFrmToIfByQueueValue	1.3.6.1.4.1.562.36.2.1.70.341.1.2	Unsigned32	read-only	This variable represents an individual value for the mscFrNniFrmToIfByQueueTable.
mscFrNniOctetToIfByQueueTable	1.3.6.1.4.1.562.36.2.1.70.342		not-accessible	This attribute counts the total number of octets transmitted from the service to the interface per emission priority queue since the component has been activated. There is potientially a maximum of 4 emission priority queues. The number of available egress queues varies according to the value of the provisionable attribute numberOfEmissionQs. Egress queue 0 has the lowest priority, while egress queue 3 has the highest priority.
mscFrNniOctetToIfByQueueEntry	1.3.6.1.4.1.562.36.2.1.70.342.1		not-accessible	An entry in the mscFrNniOctetToIfByQueueTable.
I32 mscFrNniOctetToIfByQueueIndex	1.3.6.1.4.1.562.36.2.1.70.342.1.1	Integer32	not-accessible	This variable represents the index for the mscFrNniOctetToIfByQueueTable.
U32 mscFrNniOctetToIfByQueueValue	1.3.6.1.4.1.562.36.2.1.70.342.1.2	Unsigned32	read-only	This variable represents an individual value for the mscFrNniOctetToIfByQueueTable.
frameRelayNniMIB	1.3.6.1.4.1.562.36.2.2.23
frameRelayNniGroup	1.3.6.1.4.1.562.36.2.2.23.1
frameRelayNniGroupCA	1.3.6.1.4.1.562.36.2.2.23.1.1
frameRelayNniGroupCA02	1.3.6.1.4.1.562.36.2.2.23.1.1.3
frameRelayNniGroupCA02A	1.3.6.1.4.1.562.36.2.2.23.1.1.3.2
frameRelayNniCapabilities	1.3.6.1.4.1.562.36.2.2.23.3
frameRelayNniCapabilitiesCA	1.3.6.1.4.1.562.36.2.2.23.3.1
frameRelayNniCapabilitiesCA02	1.3.6.1.4.1.562.36.2.2.23.3.1.3
frameRelayNniCapabilitiesCA02A	1.3.6.1.4.1.562.36.2.2.23.3.1.3.2

RFC description

Manages Frame Relay Network-to-Network Interface (NNI) service on Nortel MsCarrier platforms.

Start monitoring Nortel MsCarrier MscPassport switch (Frame Relay NNI links) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-MsCarrier-MscPassport-FrameRelayNniMIB

What Is Nortel-MsCarrier-MscPassport-FrameRelayNniMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description