All MIBs › Nortel-MsCarrier-MscPassport-AtmCoreMIB
Category: ATM Networking, Nortel MsCarrier MscPassport
Description: Defines core SNMP management objects for ATM switching fabric and connection management on Nortel MsCarrier MscPassport.
1,942 OIDs total — showing 1,731-1,942 (page 2 of 2)
« Prev Page 2 of 2
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| I32 mscAtmIfVptVccTxTdpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.20.294.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfVptVccTxTdpTable specific index for the mscAtmIfVptVccTxTdpTable. |
| U32 mscAtmIfVptVccTxTdpValue | 1.3.6.1.4.1.562.36.2.1.114.9.20.294.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptVccTxTdpTable. |
| mscAtmIfVptVccRxTdpTable | 1.3.6.1.4.1.562.36.2.1.114.9.20.295 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of four traffic parameters whose meanings are defined by the rxTrafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) are expressed in cells/s. Maximum burst size (MBS) is expressed in cells. Cell Delay Variation Tolerance (CDVT) is expressed in microseconds. When rxTrafficDescType is 1 or 2, none of the parameters are used. When rxTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT. When rxTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell discard; parameter 4 represents the CDVT. When rxTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell tagging; parameter 4 represents the CDVT. When rxTrafficDescType is a 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT. When rxTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT. When rxTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT. If Upc is disabled for this connection, the values of PCR, SCR, MBS and CDVT is a combination of provisioned parameters. If Upc is enabled, the values of PCR, SCR, MBS, and CDVT is exactly the values used by the usage parameter control hardware in policing the arriving traffic. These may vary slightly from the provisioned values due to granularity of the hardware. In the case where the PCR is equal to the SCR, the effective MBS is zero. | |
| mscAtmIfVptVccRxTdpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.20.295.1 | not-accessible | An entry in the mscAtmIfVptVccRxTdpTable. | |
| I32 mscAtmIfVptVccRxTdpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.20.295.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfVptVccRxTdpTable specific index for the mscAtmIfVptVccRxTdpTable. |
| U32 mscAtmIfVptVccRxTdpValue | 1.3.6.1.4.1.562.36.2.1.114.9.20.295.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptVccRxTdpTable. |
| mscAtmIfVptVccTxQThreshTable | 1.3.6.1.4.1.562.36.2.1.114.9.20.352 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the queue limit and the discard thresholds for the transmit queue of this connection. The first element indicates the queue limit. Depending upon the atmServiceCategory of the connection, the provisioned value of the transmit queue limit is derived from the txQueueLimit attribute under one of the subcomponents of the AtmIf CA component. If the connection has traffic shaping disabled, then this attribute relates to the common queue. If traffic shaping is enabled, then this attribute relates to the per-VC queue. The second element is the threshold that marks the transition from congestion state 1 to congestion state 0. This is the threshold at which traffic with discard priority (DP) = 1 is discarded. This threshold is set approximately at 90 percent of the first parameter, the operational queue limit. The third element is the threshold that marks the transition from congestion state 2 to congestion state 1. This is the threshold at which traffic with DP = 2 is discarded. This threshold is set approximately at 75 percent of the first parameter, the operational queue limit. The fourth element is the threshold that marks the transition from congestion state 3 to congestion state 2. This is the threshold at which traffic with DP = 3 is discarded. This threshold is set approximately at 35 percent of the first parameter, the operational queue limit. | |
| mscAtmIfVptVccTxQThreshEntry | 1.3.6.1.4.1.562.36.2.1.114.9.20.352.1 | not-accessible | An entry in the mscAtmIfVptVccTxQThreshTable. | |
| I32 mscAtmIfVptVccTxQThreshIndex | 1.3.6.1.4.1.562.36.2.1.114.9.20.352.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfVptVccTxQThreshTable specific index for the mscAtmIfVptVccTxQThreshTable. |
| U32 mscAtmIfVptVccTxQThreshValue | 1.3.6.1.4.1.562.36.2.1.114.9.20.352.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptVccTxQThreshTable. |
| mscAtmIfVptVccFqpTable | 1.3.6.1.4.1.562.36.2.1.114.9.20.357 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of three elements that indicate the quality of service parameters for the forward direction for this connection. This attribute is used for SPVC and SVC connections on a PNNI interface. The cdv element indicates the acceptable peak-to-peak Cell Delay Variation (CDV) of real-time connections (CBR, and rt-VBR). The ctd element indicates the acceptable maximum Cell Transfer Delay (maxCtd) of real-time connections (CBR, and rt-VBR). The clr element indicates the acceptable Cell Loss Ratio (CLR) of CBR, rt-VBR, and nrt-VBR connections. | |
| mscAtmIfVptVccFqpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.20.357.1 | not-accessible | An entry in the mscAtmIfVptVccFqpTable. | |
| INT mscAtmIfVptVccFqpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.20.357.1.1 | INTEGER | not-accessible | This variable represents the mscAtmIfVptVccFqpTable specific index for the mscAtmIfVptVccFqpTable. |
| U32 mscAtmIfVptVccFqpValue | 1.3.6.1.4.1.562.36.2.1.114.9.20.357.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptVccFqpTable. |
| mscAtmIfVptVccBqpTable | 1.3.6.1.4.1.562.36.2.1.114.9.20.358 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of three elements that indicate the quality of service parameters for the backward direction for this connection. This attribute is used for SPVC and SVC connections on a PNNI interface. The cdv element indicates the acceptable peak-to-peak Cell Delay Variation (CDV) of real-time connections (CBR, and rt-VBR). The ctd element indicates the acceptable maximum Cell Transfer Delay (maxCtd) of real-time connections (CBR, and rt-VBR). The clr element indicates the acceptable Cell Loss Ratio (CLR) of CBR, rt-VBR, and nrt-VBR connections. | |
| mscAtmIfVptVccBqpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.20.358.1 | not-accessible | An entry in the mscAtmIfVptVccBqpTable. | |
| INT mscAtmIfVptVccBqpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.20.358.1.1 | INTEGER | not-accessible | This variable represents the mscAtmIfVptVccBqpTable specific index for the mscAtmIfVptVccBqpTable. |
| U32 mscAtmIfVptVccBqpValue | 1.3.6.1.4.1.562.36.2.1.114.9.20.358.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptVccBqpTable. |
| mscAtmIfVptStateTable | 1.3.6.1.4.1.562.36.2.1.114.9.100 | not-accessible | This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which reuses this group. For component-specific information and the valid state combinations, refer to the appropriate NTP. | |
| mscAtmIfVptStateEntry | 1.3.6.1.4.1.562.36.2.1.114.9.100.1 | not-accessible | An entry in the mscAtmIfVptStateTable. | |
| INT mscAtmIfVptAdminState | 1.3.6.1.4.1.562.36.2.1.114.9.100.1.1 | INTEGER | read-only | This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock -force or Lock command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. |
| INT mscAtmIfVptOperationalState | 1.3.6.1.4.1.562.36.2.1.114.9.100.1.2 | INTEGER | read-only | This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. |
| INT mscAtmIfVptUsageState | 1.3.6.1.4.1.562.36.2.1.114.9.100.1.3 | INTEGER | read-only | This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. |
| mscAtmIfVptOperTable | 1.3.6.1.4.1.562.36.2.1.114.9.110 | not-accessible | This group contains operational information for a Vcc, Vpc, or Vpt component. | |
| mscAtmIfVptOperEntry | 1.3.6.1.4.1.562.36.2.1.114.9.110.1 | not-accessible | An entry in the mscAtmIfVptOperTable. | |
| INT mscAtmIfVptConnectionPointType | 1.3.6.1.4.1.562.36.2.1.114.9.110.1.10 | INTEGER | read-only | This attribute reflects the role of the connection component at this interface. A value of connectionEndPoint indicates that user cells, end-to-end OAM cells, and segment OAM cells are processed by the connection component. A value of segmentEndPoint indicates that user cells and end-to- end OAM cells are relayed by the connection component, while segment OAM cells are processed by the connection component. A value of connectingPoint indicates that user cells, end-to-end OAM cells, and segment OAM cells are relayed by the connection component. A value of unknown indicates that the connection component is inactive. |
| mscAtmIfVptStatusTable | 1.3.6.1.4.1.562.36.2.1.114.9.120 | not-accessible | This group contains operational status information for a Vcc, Vpc or Vpt component. | |
| mscAtmIfVptStatusEntry | 1.3.6.1.4.1.562.36.2.1.114.9.120.1 | not-accessible | An entry in the mscAtmIfVptStatusTable. | |
| INT mscAtmIfVptOperStatus | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.20 | INTEGER | read-only | This attribute indicates the present operational status of the Vcc, Vpc or Vpt component. Its value is dependent upon the current state of the segLinkSideLoopbackState and endToEndLoopbackState attributes. The value is end2endUp when the endToEndLoopbackState is good and the segLinkSideLoopbackState is either good or unknown. The value is end2endDown when the endToEndLoopbackState is bad and the segLinkSideLoopbackState is either good or unknown. The value is localUpEnd2endUnknown when the endToEndLoopbackState is unknown and the segLinkSideLoopbackState is good. The value is localDown when segLinkSideLoopbackState is bad. The value is localUpEnd2endUnknown when the endToEndLoopbackState is notApplicable and the segLinkSideLoopbackState is good. The value is unknown when the endToEndLoopbackState is either unknown or notApplicable and the segLinkSideLoopbackState is unknown. |
| INT mscAtmIfVptLocalFailureCause | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.25 | INTEGER | read-only | This attribute indicates the failure cause of the Vcc, Vpc or Vpt component. noFailure indicates that there is currently no bandwidth related failure for this connection. portDown indicates that the interface corresponding to the parent AtmIf is down. localBwLoss indicates that the Ima corresponding to this AtmIf has lost some, but not all bandwidth, and as a result, this connection has been released. notAdmitted indicates that this connection has failed to be admitted by the Connection Admission Control (CAC) algorithm. appNotRegistered indicates that there is no application registered to use this connection. This may be the case, for example when there is a Vcc Test application, but the test has not been started. Check the status of the application to determine why it is not functional. disabledByApp indicates that the application using this connection has requested that the connection be disabled. An example is a connection used by a trunk application where the trunk has timed out on an attempt to stage. Check the application to determine why it is not fully functional. bwReduced indicates that this connection is operating in a reduced bandwidth state. It is a bandwidth elastic connection which currently has been allocated less than the requested (equivalent) bandwidth. vpDown indicates that this connection has been notified of a fault detected at the associated VP-layer. vpDown is applicable for Vpt Vccs only. |
| INT mscAtmIfVptTroubled | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.28 | INTEGER | read-only | This attribute indicates whether or not the connection is in a troubled state. Connections become troubled because of OAM failures; when one of the attributes segLinkSideLoopbackState, segSwitchSideLoopbackState, endToEndLoopbackState, aisState (when receiving AIS cells only) or rdiState go bad, this attribute is set to yes; otherwise it is set to no. |
| INT mscAtmIfVptSegLinkSideLoopbackState | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.30 | INTEGER | read-only | This attribute contains the current state of the link-side segment loopback for this connection. Link-side segment loopback cells are transmitted (inserted) by a connection component in the direction of the link (port). The value of this attribute is dependent upon the current setting of the segLinkSideLoopback provisionable attribute, the connection point type as specified by the connectionPointType attribute, and the current loopback state (if applicable). The value is notApplicable when the connectionPointType is a connectingPoint. The value is notApplicable when the distributionType is pointToMultipoint. The value is good when the segLinkSideLoopback is on, the connectionPointType is a segmentEndPoint or a connectionEndPoint, and the segment link side loopback is working. The value is bad when the segLinkSideLoopback is on, the connectionPointType is a segmentEndPoint or a connectionEndPoint, and the link side segment loopback is not working. The value is unknown when the segLinkSideLoopback is off. The value is unknown when the segLinkSideLoopback is on, the connectionPointType is a segmentEndPoint and the segment switch side loopback has not yet been determined. The state of this attribute determines, in part, the value of the operStatus attribute. |
| INT mscAtmIfVptSegSwitchSideLoopbackState | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.40 | INTEGER | read-only | This attribute contains the current state of the switch-side segment loopback for this connection. Switch-side segment loopback cells are transmitted (inserted) by a connection component in the direction of the bus. The value of this attribute is dependent upon the current setting of the segSwitchSideLoopback provisionable attribute, the connection point type as specified by the connectionPointType attribute, and the current loopback state (if applicable). The value is only applicable when the connectionPointType is a segmentEndPoint. The value is notApplicable when the connectionPointType is a connectingPoint or connectionEndPoint. The value is notApplicable when the distributionType is pointToMultipoint. The value is good when the segSwitchSideLoopback is on, the connectionPointType is a segmentEndPoint and the segment switch side loopback is working. The value is bad when the segSwitchSideLoopback is on, the connectionPointType is a segmentEndPoint and the switch side segment loopback is not working. The value is unknown when the segSwitchSideLoopback is off. The value is unknown when the segSwitchSideLoopback is on, the connectionPointType is a segmentEndPoint and the segment switch side loopback has not been determined. |
| INT mscAtmIfVptEndToEndLoopbackState | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.50 | INTEGER | read-only | This attribute contains the current state of the end-to-end loopback for this connection. Its value is dependent upon the current setting of the endToEndLoopback provisionable attribute and the connection point type as specified by the connectionPointType attribute. The value is only applicable when the connectionPointType is a connectionEndPoint. The value is notApplicable when the connectionPointType is a connectingPoint or segmentEndPoint. The value is notApplicable when the distributionType is a pointToMultipoint. The value is good when the endToEndLoopback is on, the connectionPointType is a connectionEndPoint and the end-to-end loopback is working. The value is bad when the endToEndLoopback is on, the connectionPointType is a connectionEndPoint and the end-to-end loopback is not working. The value is unknown when the endToEndLoopback is off. The value is unknown when the endToEndLoopback is on, the connectionPointType is a connectionEndPoint and the end-to-end loopback status has not been determined. The state of this attribute determines, in part, the value of the operStatus attribute. |
| INT mscAtmIfVptRxOamCellCongestionState | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.55 | INTEGER | read-only | This attribute contains the current state of the receive side OAM cell congestion for this connection. Its value reflects whether the rate of received OAM cells for this connection is below a specified threshold. The connection maintains a count of the number of OAM cells which are terminated per second. Once that count exceeds the specified threshold, extraction of all OAM cells for this connection is disabled for a period of one minute. This is a congestion management mechanism to prevent the processor from being overloaded with handling OAM cells for a particular connection. This mechanism ensures that tasks, such as trunks obtain enough processor cycles to remain in service, and are not adversely affected by excessive rate of OAM cells on a particular connection. The value is good when the rate of received OAM cells is less than the allowed threshold. The value is bad when the arrival rate has exceeded the allowed threshold. It remains bad for one minute, before returning to good again. During this timeout, extraction of all OAM cells is disabled for this connection. As a result, other loopback failure conditions may occur. The value is unknown when the application has not yet begun to use this connection. An example is the Test component before a test has been started. Each type of OAM cell is counted separately. The threshold for AIS cells is three cells per second. If more than three AIS cells are received within a one second interval, this attribute is set to bad. The threshold for RDI cells and each loopback type is also three, but the threshold for trace cells is 250 per second. The state of this attribute has no direct effect on the value of the operStatus attribute or on the number of troubled connections. |
| INT mscAtmIfVptAisState | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.60 | INTEGER | read-only | This attribute contains the current state of the Alarm Indication Signal for this connection. A value of good indicates that the connection's application is active and no alarm has occurred. A value of bad indicates that the connection's application is active and an alarm has occurred. A value of unknown indicates that the connection's application is inactive. A value of notApplicable occurs when the connectionPointType is either a segmentEndPoint or a connectingPoint. |
| INT mscAtmIfVptRdiState | 1.3.6.1.4.1.562.36.2.1.114.9.120.1.70 | INTEGER | read-only | This attribute indicates the current state of the Remote Defect Indication for this connection. A value of good indicates that the connection's application is active and no alarm has occurred. A value of bad indicates that the connection's application is active and an alarm has occurred. A value of unknown indicates that the connection's application is inactive. A value of notApplicable occurs when the connectionPointType is either a segmentEndPoint or a connectingPoint. |
| mscAtmIfVptTrafficTable | 1.3.6.1.4.1.562.36.2.1.114.9.130 | not-accessible | This group is HISTORICAL. Please refer to the group AtmTmOper; This attribute group contains attributes for the Vcc and Vpc components to reflect operational traffic attributes. | |
| mscAtmIfVptTrafficEntry | 1.3.6.1.4.1.562.36.2.1.114.9.130.1 | not-accessible | An entry in the mscAtmIfVptTrafficTable. | |
| INT mscAtmIfVptTxTrafficDescType | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.10 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the type of traffic management which is applied to the transmit direction of this connection as defined in the ATM Forum. The txTrafficDescType determines the number and meaning of the parameters in the txTrafficDescParm attribute. |
| INT mscAtmIfVptTxQosClass | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.30 | INTEGER | read-only | This attribute indicates the quality of service for the transmit direction for this connection. The constantBitRate class refers to traffic offered on services such as a constant bit rate video service. This traffic is highest priority. The variableBitRate class refers to traffic offered on services such as packetized audio and video. The connectionOriented class refers to connection-oriented traffic such as Frame Relay or X.25 traffic. The connectionless traffic refers to traffic offered through connectionless trunks such as certain LAN protocols. The unspecified class supports a 'best effort' type of service, where there is a minimum guarantee of bandwidth. This traffic is lowest priority. This attribute is obsolete, replaced by the UNI 4.0 attribute atmServiceCategory. |
| INT mscAtmIfVptFwdQosClass | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.31 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the quality of service for the calling to called direction for this connection. This is only applicable to Soft PVC and SVC connections. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified QOS class; no objective is specified for the performance parameters. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance. |
| INT mscAtmIfVptTxQueueLength | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.32 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the current length of the transmit queue for this connection. If this connection has traffic shaping disabled, then this attribute displays the common queue length. If traffic shaping is enabled, then this attribute displays the per-VC queue length. |
| INT mscAtmIfVptTxQueueCongestionState | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.33 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the congestion state of the transmit queue for this connection. If the connection has traffic shaping disabled, then this attribute displays the common queue congestion state. If traffic shaping is enabled, then this attribute displays the per-VC queue congestion state. The congestion state of a queue is indicated by a numeric value ranging from 0 to 3. When a queue is in a congested state x, only traffic with discard priority (DP) 0 to x are enqueued. Traffic with DP > x is discarded. Therefore, if the congestion state is 3, there is no congestion and all traffic is enqueued. Likewise, when the congestion state is 0, there is maximum congestion and only traffic with DP=0 is enqueued on that queue. |
| INT mscAtmIfVptHoldingPriority | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.35 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the actual holding priority in effect for this connection. In a situation where the link bandwidth fluctuates, such as over an IMA link, holding priority is used to determine which connections are held and which are released. Holding priority 4 connections are the first to be released. Holding priority 0 connections are the last to be released. Some applications, for example Vcc Test, may override the provisioned holding priority. A value of notApplicable is displayed when this is an elastic connection. Holding priority does not apply to bandwidth elastic connections. Holding priority has no effect for ubr atmServiceCategory or txTrafficDescriptorType 1 or 2 connections. |
| INT mscAtmIfVptRxTrafficDescType | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.40 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the type of traffic management which is applied to the receive direction of this connection as defined in the ATM Forum. The rxTrafficDescType determines the number and meaning of the parameters in the rxTrafficDescParm attribute. |
| INT mscAtmIfVptRxQosClass | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.60 | INTEGER | read-only | This attribute reflects the value of the provisioned attribute in the Vcd or Vpd. Refer to that attribute for more detailed explanation. This attribute is obsolete replaced by the UNI 4.0 attribute atmServiceCategory. |
| INT mscAtmIfVptBwdQosClass | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.61 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the quality of service for the called to calling direction for this connection. This is only applicable to Soft PVC and SVC connections. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified QOS class; no objective is specified for the performance parameters. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance. |
| INT mscAtmIfVptAtmServiceCategory | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.62 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the ATM service category used for traffic in both directions of the connection. The constantBitRate service category is intended for real time applications, that is, those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by Cell Transfer Delay are assumed to have significantly reduced value of the application. The rtVariableBitRate service category is intended for real time applications; that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by Cell Transfer Delay are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications, that is those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection. |
| INT mscAtmIfVptTrafficShaping | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.70 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the traffic shaping state of the connection. A value of notApplicable indicates that traffic shaping is not applicable or not supported for this connection. This is the case when the atmServiceCategory is constantBitRate, or when the txTrafficDescType is 1 or 2. In these cases, the value of notApplicable is set regardless of whether traffic shaping is enabled or disabled in the provisioning data. A value of disabled indicates that traffic shaping is applicable and supported for the type of connection but has been turned off in the provisioning data. A value of enabled indicates that traffic shaping is applicable and supported for the type of connection and has been turned on in the provisioning data. This is the only case that indicates that traffic shaping is performed on the connection. In this case, the actual shaping rate is reflected in the txTrafficDescParm attribute, parameter number 4. |
| INT mscAtmIfVptBearerClassBbc | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.71 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the bearer capability for this connection. Class a service is a connection-oriented, constant bit rate ATM transport service. Class a service has end to end timing requirements and may require stringent cell loss, cell delay and cell delay variation performance.When a is displayed, the user is requesting more than an ATM only service. The network may look at the AAL to provide interworking based upon its contents. Class c service is a connection-oriented, variable bit rate ATM transport service. Class c service has no end-to-end timing requirements.When c is displayed, the user is requesting more than an ATM only service. The network interworking function may look at the AAL and provide service based on it. Class x service is a connection-oriented ATM transport service where the AAL, trafficType (cbr or vbr) and timing requirements are user defined (that is, transparent to the network). When the value of this attribute is x, the user is requesting an ATM only service from the network. In this case, the network shall not process any higher layer protocol. Class vp service is used to indicate a transparent VP service when the user is requesting an ATM only service from the network. In this case, the network does not process any higher layer protocol. This service differs from class x service in that with the class vp service both the VCI field (except for VCI values 0, 3, 4, and 6 through 15) and Payload Type field are transported transparently by the network. This attribute value is only applicable to SPVP and SVP connections. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance. |
| INT mscAtmIfVptTransferCapabilityBbc | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.72 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the transfer capability for this connection. Uni 3.0/3.1 traffic type and end-to-end timing parameters are mapped into this parameter as follows: 0: NoIndication, NoIndication 1: NoIndication, yes 2: NoIndication, no 5: CBR, yes 8: VBR, NoIndication 9: VBR, yes 10: VBR, no A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance, or in the case that the transfer capability in the call request was set to NoIndication. The CBR traffic type refers to traffic offered on services such as a constant bit rate video service or a circuit emulation. The VBR traffic type refers to traffic offered on services such as packetized audio and video, or data. The value NoIndication for traffic type is used if the user has not set the traffic type; similarly for end-to-end timing. The value yes for end-to-end timing indicates that end-to-end timing is required for the connection. The value no for end-to-end timing indicates that end-to-end timing is not required for the connection. |
| INT mscAtmIfVptClippingBbc | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.74 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the value of the clipping susceptibility parameter in the BBC Information Element. Clipping is an impairment in which the first fraction of a second of information to be transferred is lost. It occurs after a call is answered and before an associated connection is switched through. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance. |
| INT mscAtmIfVptUnshapedTransmitQueueing | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.75 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the unshaped transmit queuing state of the connection. A value of common indicates that transmit traffic is being enqueued onto common transmit queues. A value of perVc indicates that transmit traffic is being enqueued onto a per-VC queue for this connection. This is the case when trafficShaping is disabled, but per-VC queueing has been configured for this connection. A value of notApplicable indicates that transmit traffic is being shaped for this connection. Transmit traffic for a shaped connection is enqueued onto a per-VC queue, but this attribute is only applicable for unshaped connections. |
| INT mscAtmIfVptBestEffort | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.76 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates value of best effort parameter in the ATM Traffic Descriptor Information Element. The value indicated implies that the quality of service for this connection is not guaranteed. The value notIndicated implies that the quality of service for this connection is guaranteed. A value of notApplicable is displayed in the case of nailed-up PVCs for which this attribute has no significance. |
| INT mscAtmIfVptUsageParameterControl | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.80 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the UPC state of the connection. A value of notApplicable indicates that UPC is not applicable or not supported for the connection. This is the case when the connection's rxTrafficDescType is 1 or 2. A value of notApplicable is set regardless of whether UPC is disabled or enabled in provisioning data. A value of disabled indicates that UPC is applicable and supported for the type of connection but has been turned off in the provisioning data. A value of enabled indicates that UPC is applicable and supported for the type of connection and has been turned on in the provisioning data. This is the only case that indicates that UPC is enforced on the connection. In this case the traffic descriptor parameters used for UPC enforcement are reflected in the rxTrafficDescParms of the connection. |
| OCT mscAtmIfVptTxFrameDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.85 | OCTET STRING | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the set of current frame discard functions in effect in the transmit data direction at this connection point. A value of ppd indicates that the Partial Packet Discard (PPD) function is in effect. PPD may be applied at an interim connecting point for a connection which is transporting frame traffic (AAL5 at the endpoint). PPD is controlled by provisioning for PVCs and SPVCs, and by call setup parameters in the AAL and Traffic Descriptor Information Elements. A value of epd indicates that the Early Packet Discard (EPD) function is in effect at this connection endpoint. PPD and EPD are enabled by default at a connection endpoint which is performing AAL5 segmentation and assembly. Frame discard functions are not applicable for Virtual Path Connections (VPCs). Description of bits: ppd(0) epd(1) |
| OCT mscAtmIfVptRxFrameDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.86 | OCTET STRING | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the set of current frame discard functions in effect in the receive data direction at this connection point. A value of ppd indicates that the Partial Packet Discard (PPD) function is in effect. PPD may be applied at an interim connecting point for a connection which is transporting frame traffic (AAL5 at the endpoint). PPD is controlled by provisioning for PVCs and SPVCs, and by call setup parameters in the AAL and Traffic Descriptor Information Elements. A value of epd indicates that the Early Packet Discard (EPD) function is in effect at this connection endpoint. PPD and EPD are enabled by default at a connection endpoint which is performing AAL5 segmentation and assembly. Frame discard functions are not applicable for Virtual Path Connections (VPCs). Description of bits: ppd(0) epd(1) |
| INT mscAtmIfVptBandwidthElastic | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.90 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is only of importance for connections which are carried on a link with a variable bandwidth. For example, the bandwidth may be reduced in the event that one or more physical links in the IMA group fail, such that the originally requested bandwidth cannot be maintained. This attribute shows whether the application (for example, Trunk) running on this connection can continue to operate if the bandwidth is reduced. If the bandwidth is reduced, the amount by which it is reduced is displayed in the bandwidthReduction attribute. A value of yes, indicates that this connection is elastic, and the bandwidth may be reduced but the connection is not released. A value of no indicates that the bandwidth for this connection is not reduced in the event of link bandwidth reduction. However, this connection may be released based on its holdingPriority. Bandwidth elasticity has no effect for ubr atmServiceCategory or txTrafficDescriptorType 1 or 2 connections. |
| INT mscAtmIfVptBandwidthReduction | 1.3.6.1.4.1.562.36.2.1.114.9.130.1.100 | INTEGER | read-only | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute shows the amount by which the bandwidth has been reduced for this connection. This value is non-zero only for connections which have bandwidthElastic displayed as yes, and which are also operating in a reduced bandwidth mode. This is typically be the case for selected connections running over an IMA link. This attribute takes a value from 0 (no reduction) up to the ECR. All connections which are running at their full allocated bandwidth, bwReduction have the value 0. Connections which have been reduced in allocated bandwidth have a positive number for this attribute. The bwReduction may be subtracted from the ECR (which is displayed as txTrafficDescParm 5) to determine the actual bandwidth allocated to this connection. |
| mscAtmIfVptStatsTable | 1.3.6.1.4.1.562.36.2.1.114.9.140 | not-accessible | This group contains traffic statistics for a Vcc, Vpc, or Vpt component. | |
| mscAtmIfVptStatsEntry | 1.3.6.1.4.1.562.36.2.1.114.9.140.1 | not-accessible | An entry in the mscAtmIfVptStatsTable. | |
| NUM mscAtmIfVptStatsTxCell | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.10 | PassportCounter64 | read-only | This attribute counts the number of cells that have been transmitted from the interface on this connection. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsTxCellClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.20 | PassportCounter64 | read-only | This attribute counts the number of cells that have been transmitted from the interface on this connection with the CLP=1. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptTxDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.30 | PassportCounter64 | read-only | This attribute is replaced by new attributes txCellDiscard and txFrameDiscard. This attribute counts the number of cells or frames received from the bus on this connection that have been discarded. If the connection segments frames into cells, the counter indicates the number of frames discarded. Connections which segment frames into cells have a connectionPointType of connectionEndPoint. If the connection relays cells without adaptation, the counter indicates the number of cells discarded. Connections which relay cells without adaptation have a connectionPointType of segmentEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. Thus, in the AAL1 case, this attribute counts discarded cells. Discards are done due to congestion or when the connection's interface is disabled. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptTxDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.40 | PassportCounter64 | read-only | This attribute is replaced by new attributes txCellDiscardClp and txFrameDiscardClp. This attribute counts the number of cells or frames received from the bus on this connection with CLP=1 that have been discarded. If the connection segments frames into cells, the counter indicates the number of frames discarded. Connections which segment frames into cells have a connectionPointType of connectionEndPoint. If the connection relays cells without adaptation, the counter indicates the number of cells discarded. Connections which relay cells without adaptation have a connectionPointType of segmentEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. Thus, in the AAL1 case, this attribute counts discarded cells. Discards are done due to congestion or when the connection's interface is disabled. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsTxCellDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.42 | PassportCounter64 | read-only | This attribute counts the number of cells received from the bus on this connection that have been discarded. Discarded cells are not counted in the txCell attribute. Cells are discarded due to transmit congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection's interface is disabled. For CQC-based ATM cards, this attribute is applicable only to connections that relay cells without adaptation. Such connections usually have a connectionPointType of segmentEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all txCellDiscard values for all such connections associated with the Vpt. For Vccs on CQC-based ATM cards, if the connection segments frames into cells, this attribute is not applicable and is not displayed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsTxCellDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.43 | PassportCounter64 | read-only | This attribute counts the number of cells received from the bus on this connection with CLP=1 that have been discarded. This count is included in the txCellDiscard attribute. Discarded cells are not counted in the txCellClp attribute. Cells are discarded due to transmit congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection's interface is disabled. For CQC-based ATM cards, this attribute is applicable only to connections that relay cells without adaptation. Such connections have a connectionPointType of segmentEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all txCellDiscardClp values for all such connections associated with the Vpt. For Vccs on CQC-based ATM cards, if the connection segments frames into cells, this attribute is not applicable and is not displayed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsTxFrameDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.46 | PassportCounter64 | read-only | This attribute counts the number of frames received from the bus on this connection that have been discarded. Frames are discarded due to congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection interface is disabled. This count is independent of the txCell or txCellDiscard attribute. For CQC-based ATM cards, this attribute is applicable only to connections that segment frames into cells. Such connections have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all txFrameDiscard values for all such connections associated with the Vpt. For CQC-based ATM cards, for Vpcs, and Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. Discards due to EPD, PPD, and W-RED for a standard Vpt Vcc are not included in this attribute. These discards are counted in the Vcc's parent Vpt txFrameDiscard attribute. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsTxFrameDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.47 | PassportCounter64 | read-only | This attribute counts the number of discarded frames on this connection that were received from the bus and composed of one or more CLP=1 cells. Frames are discarded due to congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection interface is disabled. This count is included in the txFrameDiscard attribute. For CQC-based ATM cards, this attribute is applicable only to connections that segment frames into cells. Such connections have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all txFrameDiscardClp values for all such connections associated with the Vpt. For CQC-based ATM cards, for Vpcs and Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. Discards due to EPD, PPD, and W-RED for a standard Vpt Vcc are not included in this attribute. These discards are counted in the Vcc's parent Vpt txFrameDiscardClp attribute. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxCell | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.50 | PassportCounter64 | read-only | This attribute counts the number of cells that have been received from the interface on this connection. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxCellClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.60 | PassportCounter64 | read-only | This attribute counts the number of cells that have been received from the interface on this connection with the CLP=1. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptRxDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.70 | PassportCounter64 | read-only | This attribute is replaced by new attributes rxCellDiscard and rxFrameDiscard. This attribute counts the number of cells or frames received from the interface on this connection that have been discarded. If the connection segments frames into cells, the counter indicates the number of frames discarded. Connections which segment frames into cells have a connectionPointType of connectionEndPoint. If the connection relays cells without adaptation, the counter indicates the number of cells discarded. Connections which relay cells without adaptation have a connectionPointType of segmentEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. Thus, in the AAL1 case, this attribute counts discarded cells. Discards are done due to congestion, non-conformance with UPC or AAL reassembly problems. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptRxDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.80 | PassportCounter64 | read-only | This attribute is replaced by new attributes rxCellDiscardClp and rxFrameDiscardClp. This attribute counts the number of cells or frames received from the interface on this connection with CLP=1 that have been discarded. If the connection segments frames into cells, the counter indicates the number of frames discarded. Connections which segment frames into cells have a connectionPointType of connectionEndPoint. If the connection relays cells without adaptation, the counter indicates the number of cells discarded. Connections which relay cells without adaptation have a connectionPointType of segmentEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. Thus, in the AAL1 case, this attribute counts discarded cells. Discards are done due to congestion, non-conformance with UPC or AAL reassembly problems. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxCellDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.82 | PassportCounter64 | read-only | This attribute counts the number of cells received from the interface on this connection that have been discarded. This count is included in the rxCell attribute. This count includes cells discarded due to non-conformance with UPC, cells which are part of a frame which has been discarded due to an AAL5 frame reassembly error, cells which are discarded due to congestion, or cells which are received while the next hop connection to which the traffic is directed across the backplane is down. The next hop connection is the Vcc or Vpc identified by the nextHop attribute of the Nrp or Rp component. For CQC-based ATM cards, this attribute is applicable only to connections that relay cells without adaptation. Such connections have a connectionPointType of connectionEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all rxCellDiscard values for all such connections associated with the Vpt. For CQC-based ATM cards, for Vpcs, and Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. Discards due to non-conformance with UPC at the VP layer, for a standard Vpt Vcc, are not included in this attribute. These discards are counted in the Vcc's parent Vpt rxCellDiscard attribute. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxCellDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.83 | PassportCounter64 | read-only | This attribute counts the number of cells received from the interface on this connection with CLP=1 that have been discarded. This count is included in the rxCell and rxCellDiscard attributes. This count includes cells discarded due to non-conformance with UPC, cells which are part of a frame which has been discarded due to an AAL5 frame reassembly error, cells which are discarded due to congestion, or cells which are received while the next hop connection to which the traffic is directed across the backplane is down. The next hop connection is the Vcc or Vpc identified by the nextHop attribute of the Nrp or Rp component. For CQC-based ATM cards, this attribute is applicable only to connections that relay cells without adaptation. Such connections have a connectionPointType of connectionEndPoint or connectingPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all rxCellDiscard values for all such connections associated with the Vpt. For CQC-based ATM cards, for Vpcs, and Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. Discards due to non-conformance with UPC at the VP layer, for a standard Vpt Vcc, are not included in this attribute. These discards are counted in the Vcc's parent Vpt rxCellDiscard attribute. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxFrameDiscard | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.86 | PassportCounter64 | read-only | This attribute counts the number of frames received from the interface on this connection that have been discarded. This count is independent of the rxCellDiscard attribute. This count includes frames discarded due to an AAL5 frame reassembly error, frames discarded due to early packet discard (EPD), and frames discarded due to processor (CPU) congestion. This attribute is applicable only to connections that reassemble incoming cells into frames. Connections which reassemble cells into frames have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; even though they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all rxFrameDiscard values for all applicable connections associated with the Vpt. For Vpcs and for Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxFrameDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.88 | PassportCounter64 | read-only | This attribute counts the number of discarded frames on this connection that were received from the interface and composed of one or more CLP1 cells. This count is included in the rxFrameDiscard attribute. It is independent of the rxCellDiscard attribute. This count includes frames discarded due to an AAL5 frame reassembly error, frames discarded due to early packet discard (EPD), and frames discarded due to processor (CPU) congestion. This attribute is applicable only to connections that reassemble incoming cells into frames. Such connections have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all rxFrameDiscardClp values for all applicable connections associated with the Vpt. For Vpcs and for Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxUpcViolationOnEnforcer1 | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.90 | PassportCounter64 | read-only | This attribute counts the number of UPC violations observed by the Generic Cell Rate Algorithm (GCRA) Enforcer 1. This attribute is only applicable if UPC is enforced or monitored. This attribute is not applicable for standard Vpt Vccs. This attribute is not applicable and is not displayed on CQC-based ATM cards. When the value of rxTrafficDescType for this connection is 3, 4, 5, 6, 7 or 8, Enforcer 1 enforces conformance of traffic received from the interface to PCR CLP0+1. When the value of rxTrafficDescType for this connection is 9, Enforcer 1 performs the Dynamic Generic Cell Rate Algorithm (DGCRA) used for the Available Bit Rate (ABR) service category. If UPC is enforced all non-conforming cells are discarded by this enforcer. These discarded cells are included in rxCellDiscard. For basic Vpts, this attribute provides an aggregated total of all rxUpcViolationOnEnforcer1 values for the Vccs associated with the Vpt. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxUpcViolationOnEnforcer2 | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.92 | PassportCounter64 | read-only | This attribute counts the number of UPC violations observed by the Generic Cell Rate Algorithm (GCRA) Enforcer 2. This attribute is only applicable if UPC is enforced or monitored. This attribute is not applicable for standard Vpt Vccs. This attribute is not applicable and is not displayed on CQC-based ATM cards. Enforcer2 is applicable only if the rxTrafficDescType for this connection is 4, 5, 6, 7 or 8. When the value of rxTrafficDescType 4 or 5, Enforcer 2 enforces conformance of traffic received from the interface to PCR CLP0. When the value of rxTrafficDescType 6, Enforcer 2 enforces conformance of traffic received from the interface to SCR CLP0+1. When the value of rxTrafficDescType 7 or 8, Enforcer 2 enforces conformance of traffic received from the interface to SCR CLP0. If UPC is enforced, enforcer 2 discards non-conforming cells for rxTrafficDescType values of 4, 6 and 7. It tags non-conforming cells for rxTrafficDescType values of 5 and 8. Discarded cells are counted in the rxCellDiscard attribute. For basic Vpts, this attribute provides an aggregated total of all rxUpcViolationOnEnforcer2 values for the Vccs associated with the Vpt. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxAal5FrameError | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.100 | PassportCounter64 | read-only | This attribute counts the number of frames received from the interface on this connection that have AAL5 length errors or AAL5 CRC errors. This attribute is not applicable and is not displayed on CQC-based ATM cards. AAL5 length or CRC errors typically occur because of cell discards due to congestion, UPC, or due to corruption of data between the AAL5 segmentation and reassembly end points. This attribute is applicable only to connections that reassemble incoming cells into frames. Such connections have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all rxAal5FrameError values for all applicable connections associated with the Vpt. For Vpcs and for Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfVptStatsRxAal5FrameAbort | 1.3.6.1.4.1.562.36.2.1.114.9.140.1.102 | PassportCounter64 | read-only | This attribute counts the number of frames received from the interface on this connection that have the AAL5 length field set to zero. This attribute is not applicable and is not displayed for CQC-based ATM cards. An AAL5 length of zero is an indication by the far end segmentation point to this reassembly point that the frame is to be discarded without reassembly. This mechanism is typically used by a segmentation point if it detects an error in a frame after some of the cells belonging to that frame have already been transmitted. This attribute is applicable only to connections that reassemble incoming cells into frames. Such connections have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; although they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. For Vpts, this attribute provides an aggregated total of all rxAal5FrameAbort values for all applicable connections associated with the Vpt. For Vpcs and for Vccs that relay cells without adaptation, this attribute is not applicable and is not displayed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. |
| mscAtmIfVptTxTdpTable | 1.3.6.1.4.1.562.36.2.1.114.9.294 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of five transmit traffic parameters. The first three elements reflect the settings of the first three elements of the txTrafficDescParm attribute in the AtmTrafficProv group. When txTrafficDescType is 1 or 2, parameters 1 through 5 are unused. In this description, PCR is the greater of either the PCR or the requested shaping rate (parameter 1 or parameter 5) specified in the Traffic group under the Vcd or Vpd. When txTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 or 1 traffic; parameters 2 and 3 are unused. When txTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell discard. When txTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell tagging. When txTrafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic. When txTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic. When txTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic When txTrafficDescType is 3, 4, 5, 6, 7 or 8, parameter 4 reflects the actual shaping rate in cell/s for this connection. This rate is one of the set of available shaping rates for this type of ATM-FP, based on the number of interfaces doing shaping (attribute perVcQueueInterfaces), the provisioned cell rate, the shapingScalingFactor attribute of the AtmResourceControl component, and whether traffic shaping is enabled. A rate of zero (0) indicates that shaping is not performed. When txTrafficDescType is 3, 4, 5, 6, 7 or 8, parameter 5 reflects the equivalent cell rate in cell/s for this connection as determined by the Connection Admission Control (CAC) algorithm. The equivalent cell rate is useful in determining the admission characteristics of this connection. | |
| mscAtmIfVptTxTdpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.294.1 | not-accessible | An entry in the mscAtmIfVptTxTdpTable. | |
| I32 mscAtmIfVptTxTdpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.294.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfVptTxTdpTable specific index for the mscAtmIfVptTxTdpTable. |
| U32 mscAtmIfVptTxTdpValue | 1.3.6.1.4.1.562.36.2.1.114.9.294.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptTxTdpTable. |
| mscAtmIfVptRxTdpTable | 1.3.6.1.4.1.562.36.2.1.114.9.295 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of four traffic parameters whose meanings are defined by the rxTrafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) are expressed in cells/s. Maximum burst size (MBS) is expressed in cells. Cell Delay Variation Tolerance (CDVT) is expressed in microseconds. When rxTrafficDescType is 1 or 2, none of the parameters are used. When rxTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT. When rxTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell discard; parameter 4 represents the CDVT. When rxTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell tagging; parameter 4 represents the CDVT. When rxTrafficDescType is a 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT. When rxTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT. When rxTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT. If Upc is disabled for this connection, the values of PCR, SCR, MBS and CDVT is a combination of provisioned parameters. If Upc is enabled, the values of PCR, SCR, MBS, and CDVT is exactly the values used by the usage parameter control hardware in policing the arriving traffic. These may vary slightly from the provisioned values due to granularity of the hardware. In the case where the PCR is equal to the SCR, the effective MBS is zero. | |
| mscAtmIfVptRxTdpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.295.1 | not-accessible | An entry in the mscAtmIfVptRxTdpTable. | |
| I32 mscAtmIfVptRxTdpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.295.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfVptRxTdpTable specific index for the mscAtmIfVptRxTdpTable. |
| U32 mscAtmIfVptRxTdpValue | 1.3.6.1.4.1.562.36.2.1.114.9.295.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptRxTdpTable. |
| mscAtmIfVptTxQThreshTable | 1.3.6.1.4.1.562.36.2.1.114.9.352 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute indicates the queue limit and the discard thresholds for the transmit queue of this connection. The first element indicates the queue limit. Depending upon the atmServiceCategory of the connection, the provisioned value of the transmit queue limit is derived from the txQueueLimit attribute under one of the subcomponents of the AtmIf CA component. If the connection has traffic shaping disabled, then this attribute relates to the common queue. If traffic shaping is enabled, then this attribute relates to the per-VC queue. The second element is the threshold that marks the transition from congestion state 1 to congestion state 0. This is the threshold at which traffic with discard priority (DP) = 1 is discarded. This threshold is set approximately at 90 percent of the first parameter, the operational queue limit. The third element is the threshold that marks the transition from congestion state 2 to congestion state 1. This is the threshold at which traffic with DP = 2 is discarded. This threshold is set approximately at 75 percent of the first parameter, the operational queue limit. The fourth element is the threshold that marks the transition from congestion state 3 to congestion state 2. This is the threshold at which traffic with DP = 3 is discarded. This threshold is set approximately at 35 percent of the first parameter, the operational queue limit. | |
| mscAtmIfVptTxQThreshEntry | 1.3.6.1.4.1.562.36.2.1.114.9.352.1 | not-accessible | An entry in the mscAtmIfVptTxQThreshTable. | |
| I32 mscAtmIfVptTxQThreshIndex | 1.3.6.1.4.1.562.36.2.1.114.9.352.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfVptTxQThreshTable specific index for the mscAtmIfVptTxQThreshTable. |
| U32 mscAtmIfVptTxQThreshValue | 1.3.6.1.4.1.562.36.2.1.114.9.352.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptTxQThreshTable. |
| mscAtmIfVptFqpTable | 1.3.6.1.4.1.562.36.2.1.114.9.357 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of three elements that indicate the quality of service parameters for the forward direction for this connection. This attribute is used for SPVC and SVC connections on a PNNI interface. The cdv element indicates the acceptable peak-to-peak Cell Delay Variation (CDV) of real-time connections (CBR, and rt-VBR). The ctd element indicates the acceptable maximum Cell Transfer Delay (maxCtd) of real-time connections (CBR, and rt-VBR). The clr element indicates the acceptable Cell Loss Ratio (CLR) of CBR, rt-VBR, and nrt-VBR connections. | |
| mscAtmIfVptFqpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.357.1 | not-accessible | An entry in the mscAtmIfVptFqpTable. | |
| INT mscAtmIfVptFqpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.357.1.1 | INTEGER | not-accessible | This variable represents the mscAtmIfVptFqpTable specific index for the mscAtmIfVptFqpTable. |
| U32 mscAtmIfVptFqpValue | 1.3.6.1.4.1.562.36.2.1.114.9.357.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptFqpTable. |
| mscAtmIfVptBqpTable | 1.3.6.1.4.1.562.36.2.1.114.9.358 | not-accessible | This attribute is HISTORICAL. Please refer to the attribute of the same name in the group AtmTmOper. This attribute is a vector of three elements that indicate the quality of service parameters for the backward direction for this connection. This attribute is used for SPVC and SVC connections on a PNNI interface. The cdv element indicates the acceptable peak-to-peak Cell Delay Variation (CDV) of real-time connections (CBR, and rt-VBR). The ctd element indicates the acceptable maximum Cell Transfer Delay (maxCtd) of real-time connections (CBR, and rt-VBR). The clr element indicates the acceptable Cell Loss Ratio (CLR) of CBR, rt-VBR, and nrt-VBR connections. | |
| mscAtmIfVptBqpEntry | 1.3.6.1.4.1.562.36.2.1.114.9.358.1 | not-accessible | An entry in the mscAtmIfVptBqpTable. | |
| INT mscAtmIfVptBqpIndex | 1.3.6.1.4.1.562.36.2.1.114.9.358.1.1 | INTEGER | not-accessible | This variable represents the mscAtmIfVptBqpTable specific index for the mscAtmIfVptBqpTable. |
| U32 mscAtmIfVptBqpValue | 1.3.6.1.4.1.562.36.2.1.114.9.358.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfVptBqpTable. |
| mscAtmIfEp | 1.3.6.1.4.1.562.36.2.1.114.10 | |||
| mscAtmIfEpRowStatusTable | 1.3.6.1.4.1.562.36.2.1.114.10.1 | not-accessible | This entry controls the addition and deletion of mscAtmIfEp components. | |
| mscAtmIfEpRowStatusEntry | 1.3.6.1.4.1.562.36.2.1.114.10.1.1 | not-accessible | A single entry in the table represents a single mscAtmIfEp component. | |
| ROW mscAtmIfEpRowStatus | 1.3.6.1.4.1.562.36.2.1.114.10.1.1.1 | RowStatus | read-write | This variable is used as the basis for SNMP naming of mscAtmIfEp components. These components can be added and deleted. |
| STR mscAtmIfEpComponentName | 1.3.6.1.4.1.562.36.2.1.114.10.1.1.2 | DisplayString | read-only | This variable provides the component's string name for use with the ASCII Console Interface |
| STO mscAtmIfEpStorageType | 1.3.6.1.4.1.562.36.2.1.114.10.1.1.4 | StorageType | read-only | This variable represents the storage type value for the mscAtmIfEp tables. |
| I32 mscAtmIfEpIndex | 1.3.6.1.4.1.562.36.2.1.114.10.1.1.10 | Integer32 | not-accessible | This variable represents the index for the mscAtmIfEp tables. |
| mscAtmIfEpProvTable | 1.3.6.1.4.1.562.36.2.1.114.10.100 | not-accessible | This group contains provisioned attributes which specify the behavior of an emission priority for the ATM interface. | |
| mscAtmIfEpProvEntry | 1.3.6.1.4.1.562.36.2.1.114.10.100.1 | not-accessible | An entry in the mscAtmIfEpProvTable. | |
| U32 mscAtmIfEpMinimumBandwidthGuarantee | 1.3.6.1.4.1.562.36.2.1.114.10.100.1.1 | Unsigned32 | read-write | This attribute specifies the minimum bandwidth guarantee associated with this EmissionPriority. A minimum bandwidth guarantee is designed to prevent starvation of traffic at this EP by traffic at higher EPs. Minimum bandwidth guarantees only operate for EPs within the guaranteed bandwidth range 2 through 7. Note, that for APC-based cards, EPs 5 and 6 are not supported. The minimum bandwidth guarantee specified is a percentage of the bandwidth which remains after all traffic at EP 0 and EP 1 is served. For example, if EP 0 and EP 1 traffic consumes 20% of link bandwidth, the minimum bandwidth guarantee applies to the remaining 80% of the link bandwidth. A minimum bandwidth guarantee of 2% would actually result in this EP getting 2% of 80% (total 1.6%) of the link bandwidth. The sum of minimumBandwidthGuarantee values for all Eps under an AtmIf must not exceed 100%. The value priority specifies that this Ep gets the bandwidth guarantee which is applicable based on the hierarchy of emission priorities. In this case, there is no minimum bandwidth guarantee. For all non Apc-based cards the allowed value of the attribute is between 0 and 48. Such a value specifies that from 1% to 48% of the remaining link bandwidth is reserved for traffic at this EP. Given a value n of minimumBandwidthGuarantee, then for n% of transmit cell opportunities in the guaranteed bandwidth range, this EP get first opportunity to send a cell. If this EP uses less than n% of the link bandwidth, the extra opportunities are allocated in priority. Due to scheduling and cell arrival times, traffic at this EP may not necessarily achieve full utilization of its minimum bandwidth guarantee. When specifying a value for minimumBandwidthGuarantee, consider the effect on cell delay variation (CDV) of traffic which would normally be of higher priority. For example, if RtVbr service category traffic is assigned to Ep/2 and Ubr traffic is assigned on Ep/7 where Ep/7 has a minimumBandwidthGuarantee of 25%, there can be a large impact on CDV of the RtVbr traffic. Traffic of the Cbr or RtVbr service category which is sensitive to CDV and is of known volume, can be assigned on EP 0 or EP 1 which are independent of the effects of minimum bandwidth guarantee. VALUES ( 0 = priority ) |
| mscAtmIfPm | 1.3.6.1.4.1.562.36.2.1.114.11 | |||
| mscAtmIfPmRowStatusTable | 1.3.6.1.4.1.562.36.2.1.114.11.1 | not-accessible | This entry controls the addition and deletion of mscAtmIfPm components. | |
| mscAtmIfPmRowStatusEntry | 1.3.6.1.4.1.562.36.2.1.114.11.1.1 | not-accessible | A single entry in the table represents a single mscAtmIfPm component. | |
| ROW mscAtmIfPmRowStatus | 1.3.6.1.4.1.562.36.2.1.114.11.1.1.1 | RowStatus | read-only | This variable is used as the basis for SNMP naming of mscAtmIfPm components. These components cannot be added nor deleted. |
| STR mscAtmIfPmComponentName | 1.3.6.1.4.1.562.36.2.1.114.11.1.1.2 | DisplayString | read-only | This variable provides the component's string name for use with the ASCII Console Interface |
| STO mscAtmIfPmStorageType | 1.3.6.1.4.1.562.36.2.1.114.11.1.1.4 | StorageType | read-only | This variable represents the storage type value for the mscAtmIfPm tables. |
| NON mscAtmIfPmIndex | 1.3.6.1.4.1.562.36.2.1.114.11.1.1.10 | NonReplicated | not-accessible | This variable represents the index for the mscAtmIfPm tables. |
| mscAtmIfPmProvTable | 1.3.6.1.4.1.562.36.2.1.114.11.100 | not-accessible | This group contains provisioned attributes which specify the default Performance Monitoring (PM) measurements, namely, Cell Loss Ratio (CLR) and Availability Ratio (AR), and control modes for all AtmIf Vcc and AtmIf Vpc connections on the ATM interface. | |
| mscAtmIfPmProvEntry | 1.3.6.1.4.1.562.36.2.1.114.11.100.1 | not-accessible | An entry in the mscAtmIfPmProvTable. | |
| OCT mscAtmIfPmSegSwitchSideMeasurement | 1.3.6.1.4.1.562.36.2.1.114.11.100.1.1 | OCTET STRING | read-write | This attribute specifies the default Performance Monitoring (PM) measurements on the switch side configuration for all AtmIf Vcc and AtmIf Vpc connections on the ATM interface. Description of bits: availabilityRatio(0) cellLossRatio(1) |
| OCT mscAtmIfPmSegLinkSideMeasurement | 1.3.6.1.4.1.562.36.2.1.114.11.100.1.2 | OCTET STRING | read-write | This attribute specifies the default Performance Monitoring (PM) measurements on the link side configuration for all AtmIf Vcc and AtmIf Vpc connections, on the ATM interface. Description of bits: availabilityRatio(0) cellLossRatio(1) |
| INT mscAtmIfPmControlMode | 1.3.6.1.4.1.562.36.2.1.114.11.100.1.3 | INTEGER | read-write | This attribute specifies the default control mode of Performance Monitoring (PM) measurements for all AtmIf Vcc and AtmIf Vpc connections on the ATM interface. autoStart means Performance Monitoring (PM) measurements start when the provisioned data is activated. onDemand means PM measurements start when the operator issues the START conmmand. The PM measurements in this mode will continue until the operator issues the STOP command. |
| mscAtmIfCidDataTable | 1.3.6.1.4.1.562.36.2.1.114.100 | not-accessible | This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs. | |
| mscAtmIfCidDataEntry | 1.3.6.1.4.1.562.36.2.1.114.100.1 | not-accessible | An entry in the mscAtmIfCidDataTable. | |
| U32 mscAtmIfCustomerIdentifier | 1.3.6.1.4.1.562.36.2.1.114.100.1.1 | Unsigned32 | read-write | This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers. |
| mscAtmIfProvTable | 1.3.6.1.4.1.562.36.2.1.114.110 | not-accessible | This group contains provisionable attributes for the AtmIf component. | |
| mscAtmIfProvEntry | 1.3.6.1.4.1.562.36.2.1.114.110.1 | not-accessible | An entry in the mscAtmIfProvTable. | |
| LIN mscAtmIfInterfaceName | 1.3.6.1.4.1.562.36.2.1.114.110.1.10 | Link | read-write | This attribute associates the AtmIf component with a specific interface on a Function Processorfor example, Lp/1 Ds3/0. This implicitly defines the logical processor on which the AtmIf is activated. |
| INT mscAtmIfType | 1.3.6.1.4.1.562.36.2.1.114.110.1.20 | INTEGER | read-write | This attribute indicates the type of AtmIf, either uni or ppi. These types differ only in their handling of OAM cellsall connections passing through a uni interface terminate segment loopback cells; whereas a ppi interface permits these cells to be passed transparently. This is obsoleted. The value is migrated into oamSegmentBoundary. uni maps to yes. ppi maps to no. |
| INT mscAtmIfOamSegmentBoundary | 1.3.6.1.4.1.562.36.2.1.114.110.1.30 | INTEGER | read-write | This attribute specifies whether the interface is on an OAM segment boundary. When yes is selected, the interface is on an OAM segment boundary and all connections passing through the interface terminate OAM segment cells. When no is selected, the interface is not on an OAM segment boundary and the interface permits the segment cells to be passed transparently. |
| U32 mscAtmIfMaxVpcs | 1.3.6.1.4.1.562.36.2.1.114.110.1.40 | Unsigned32 | read-write | This attribute specifies the maximum number of VPCs that can be configured on this AtmIf. The value must not exceed the total number of usable VPCs supported by this AtmIf (which is equal to 256 or (256 - (number of VPIs used for VCCs)), according to the ConnectionMapping component). Furthermore, if the AtmIf is linked to an LogicalProcessor of cardType other than 3pE3Atm, 3pDS3Atm, 3pOC3MmAtm, 3pOC3SmAtm, 3pE1Atm, 3pDS1Atm, 2pJ6MAtm, the sum of (maxVccs + maxVpcs + 1) across all AtmIf linked to that Lp must be less than or equal to the totalConnectionPoolCapacity attribute of the Arc component. If the Arc component doesn't exist, the default value of totalConnectionPoolCapacity is used as the limit. This attribute has been migrated to the Ca component. |
| U32 mscAtmIfMaxVccs | 1.3.6.1.4.1.562.36.2.1.114.110.1.50 | Unsigned32 | read-write | This attribute specifies the maximum number of usable VCCs that can be configured on this AtmIf. The value must not exceed the number of non-reserved VCC identifiers in the Vcc space supported by this AtmIf (which is specified by the ConnectionMapping component). Furthermore, if the AtmIf is linked to an LogicalProcessor of cardType other than 3pE3Atm, 3pDS3Atm, 3pOC3MmAtm, 3pOC3SmAtm, 3pE1Atm, 3pDS1Atm, 2pJ6MAtm, the sum of (maxVccs + maxVpcs + 1) across all AtmIf linked to that Lp must be less than the totalConnectionPoolCapacity attribute of the Arc component. If the Arc component doesn't exist, the default value of totalConnectionPoolCapacity is used as the limit. This attribute has been migrated to the Ca component. |
| INT mscAtmIfTrafficShaping | 1.3.6.1.4.1.562.36.2.1.114.110.1.60 | INTEGER | read-write | It is migrated in P6.0 to a combination of the trafficShaping attributes and the emissionPriority attributes under each ATM service category component of the AtmIf CA. This attribute defines whether traffic shaping is enabled or disabled for the entire AtmIf. When this attribute is set to enabled, each provisioned connection under the interface can be individually provisioned to permit or prohibit traffic shaping. When this attribute is set to disabled, no traffic shaping is performed on the transmit path for any of the connections. This attribute may be set to enabled if the interface supports shaping, as defined by the perVcQueueInterfaces attribute in the AtmResourceControl component. If the AtmResourceControl component does not exist, this attribute may not be set to enabled. |
| INT mscAtmIfUnshapedTransmitQueueing | 1.3.6.1.4.1.562.36.2.1.114.110.1.70 | INTEGER | read-write | It is migrated in P6.0 to the attributes of the same name under each ATM service category component of the AtmIf CA. This attribute applies only for unshaped VCC and VPC connections. This attribute defines the transmit queueing method for all unshaped connections under this AtmIf. Per-VC queueing means that unshaped connections are treated with the same fairness as shaped queues in the transmit round-robin scheduling. The alternative to per-VC queueing is to use the common queue for a particular service category (medium or low priority). The common queue is only counted as one queue in the transmit round-robin scheduling. Thus, if there are multiple connections which are destined for the common queue, they are not fairly allocated a portion of the transmit bandwidth compared to shaped connections. When this attribute is set to perVc, any unshaped connection is allocated its own per-VC queue, and is treated with the same fairness as any shaped connections. Per-VC queues have a maximum rate of 58,962 cell/s (25 Mbit/s) in a multi-port shaping configuration. Per-VC queues also have their own congestion control level. This means that total number of cell/frame blocks allocated for several per-VC queues are higher than would be allowed on the common queue. This can be an advantage in reducing cell loss due to queue congestion. This attribute may only be set to perVc if the interface supports per-VC queueing, (specified by the perVcQueueInterfaces attribute in the AtmResourceControl component). When this attribute is set to common, any unshaped connection is destined for the common queue. The common queue has one set of congestion control levels for all cells enqueued on it. The common queue is only allocated one queue position when scheduling which queue to transmit from. Due to the possibility of unfairness, this value is only recommended in cases where the configuration cannot otherwise achieve full link utilization. When this attribute is set to autoConfigure and the interface support per-VC queueing (specified by the perVcQueueInterfaces attribute in the AtmResourceControl component) per-VC queueing is enabled for all unshaped connections. Otherwise, the common queue is used. The unshapedTransmitQueueingOper attribute indicates whether the transmit queueing is perVc or common. |
| INT mscAtmIfUsageParameterControl | 1.3.6.1.4.1.562.36.2.1.114.110.1.80 | INTEGER | read-write | It is migrated in P6.0 to the attributes of the same name under each ATM service category component of the AtmIf CA. This attribute defines whether usage parameter control (UPC) is enabled or disabled for receive traffic for Vcc and Vpc connections for this entire AtmIf. When this attribute is set to enabled, each provisioned connection under the interface can be individually provisioned to enforce or ignore UPC. When this attribute is set to disabled, UPC cannot be enabled on the receive path for any of the connections. |
| U32 mscAtmIfMaxVpiBits | 1.3.6.1.4.1.562.36.2.1.114.110.1.85 | Unsigned32 | read-write | This attribute specifies the maximum number of VPI bits that may be active for this AtmIf. These bits start at the least significant bit position and are contiguous. In general, the maximum VPI which may be used on the interface is 2**maxVpiBits - 1. The value of the remaining (inactive) VPI bits is ignored on cells received from the link. If the AtmIf is linked to a LogicalProcessor of cardType 3pOC3MmAtm, 3pOC3SmAtm, 3pE3Atm, 3pDS3Atm, 3pE1Atm, 3pDS1Atm, or 2pJ6MAtm, the value of this attribute must be 8. The maximum VPI supported on these card types is 255. If the AtmIf is linked to a LogicalProcessor of any other cardType, the value of this attribute may be 8 or 12. The maximum VPI supported on these card types is 4095. An exception is that cardType 8pE1Atm and 8pDS1Atm do not support VPI 4095; the maximum VPI on these card types is 4094. If a Uni or an Iisp component is present directly under the AtmIf, the value of this attribute must be 8. |
| STR mscAtmIfRemoteAtmInterfaceLabel | 1.3.6.1.4.1.562.36.2.1.114.110.1.90 | AsciiString | read-write | This attribute specifies a unique indication of the remote ATM service or interface component connected to this one. The value of this attribute can be used by network management applications to discover the network's ATM topology from its configuration information. The syntax of the value, such as component ID, address, or other numerical identifier, must follow the conventions of the network management platform. In absence of such convention or platform, the value should be left empty. The value is only stored by the module. It is neither validated nor used to perform any form of remote connectivity validation. |
| U32 mscAtmIfTxCellMemory | 1.3.6.1.4.1.562.36.2.1.114.110.1.91 | Unsigned32 | read-write | This attribute specifies the percentage of the Lp/x Eng Arc Aqm/0 txCellMemoryThreshold 0 attribute. This attribute only applies to ATM IP FPs. It is ignored on all other card types. For ATM IP FPs, the cell memory which is displayed in Lp/x Eng Arc Aqm/0 txCellMemoryThreshold 0 is shared across all interfaces for the card. This attribute allows the allocation of a specific proportion of the transmit cell memory for the use of connections under this AtmIf. If the value of this attribute is specified as 100, connections under this AtmIf may use up to 100% of the transmit cell memory. If this attribute is specified as an amount less than 100, then only that percentage of the transmit cell memory may be used by connections under this AtmIf. By specifying values for this attribute under the AtmIf's on a DS3, E3 or MSA32 card, you can limit the transmit cell memory usage for each AtmIf. This is used to guarantee that all cell traffic for an AtmIf will respect the cell loss priority (CLP) bit settings regardless of the atmServiceCategory for the connection. |
| INT mscAtmIfFaultHoldOffTime | 1.3.6.1.4.1.562.36.2.1.114.110.1.100 | INTEGER | read-write | This attribute specifies the delay before faults detected at the VP layer are propagated to the VC layer, and thus to the application using the connection. If the value is 0 (zero), applications using a VirtualPathTerminator are immediately notified of faults detected by the VP. Using this value allows these applications to be advised of faults without requiring loopbacks on each Vcc. Typically, the application goes out of service when advised of a fault. If the value is infinity, applications are not notified of VP layer faults. Using this value allows the applications to survive transient VP layer fault conditions. The value chosen applies only to Vpts and Vccs directly beneath a Vpt. |
| INT mscAtmIfCtdCalculation | 1.3.6.1.4.1.562.36.2.1.114.110.1.110 | INTEGER | read-write | This attribute specifies whether cell transfer delay calculation should be performed on loopback cells for each SPVC and SPVP connection under this interface. Cell transfer delay is calculated as half of the measured segment round trip delay of a loopback cell. Cell transfer delay calculation is only supported when segment switch side loopback is enabled on the source segment endpoint. Cell transfer delay calculation is only performed on supported connections when the accountCollection attribute of the AtmIf Uni or AtmIf Iisp component has a non-empty reason. Cell transfer delay calculation is not provided for connections under the Vpt. |
| mscAtmIfLbkTable | 1.3.6.1.4.1.562.36.2.1.114.120 | not-accessible | This group contains the default loopback attribute values for all Vcc, Vpc and Vpt components. Note that these attribute values can be overridden by setting different values in the Vcd component of the provisioned Vcc or the Vpd component of the provisioned Vpc or Vpt. Certain loopback requests may not be possible on a given connection. In such cases, the corresponding operational loopback attribute in the AtmStatus group of the Vcc, Vpc, or Vpt component is set to notApplicable and the requested loopback is not performed. | |
| mscAtmIfLbkEntry | 1.3.6.1.4.1.562.36.2.1.114.120.1 | not-accessible | An entry in the mscAtmIfLbkTable. | |
| INT mscAtmIfSegLinkSideLoopback | 1.3.6.1.4.1.562.36.2.1.114.120.1.10 | INTEGER | read-write | This attribute specifies the default value for link-side segment loopback insertion for all connections under this interface. Link- side segment loopback is not possible if the oamSegmentBoundary attribute of the AtmIf component is no. |
| INT mscAtmIfSegSwitchSideLoopback | 1.3.6.1.4.1.562.36.2.1.114.120.1.20 | INTEGER | read-write | This attribute specifies the default value for switch-side segment loopback insertion for all connections under this interface. Switch- side segment loopback is not possible if the oamSegmentBoundary attribute of the AtmIf component is no. |
| INT mscAtmIfEndToEndLoopback | 1.3.6.1.4.1.562.36.2.1.114.120.1.30 | INTEGER | read-write | This attribute specifies the default value for end-to-end loopback insertion for all connections under this interface. End-to-end loopback insertion is not possible if the connectionPointType attribute of the Vcc or Vpc component is connectingPoint or segmentEndPoint. End-to-end loopback insertion is possible if the connectionPointType attribute of the Vcc or Vpc component is connectionEndPoint. End-to-end loopback insertion is always possible on a Vpt component. |
| mscAtmIfStateTable | 1.3.6.1.4.1.562.36.2.1.114.130 | not-accessible | This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which reuses this group. For component-specific information and the valid state combinations, refer to the appropriate NTP. | |
| mscAtmIfStateEntry | 1.3.6.1.4.1.562.36.2.1.114.130.1 | not-accessible | An entry in the mscAtmIfStateTable. | |
| INT mscAtmIfAdminState | 1.3.6.1.4.1.562.36.2.1.114.130.1.1 | INTEGER | read-only | This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock -force or Lock command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component. |
| INT mscAtmIfOperationalState | 1.3.6.1.4.1.562.36.2.1.114.130.1.2 | INTEGER | read-only | This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component. |
| INT mscAtmIfUsageState | 1.3.6.1.4.1.562.36.2.1.114.130.1.3 | INTEGER | read-only | This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component. |
| OCT mscAtmIfAvailabilityStatus | 1.3.6.1.4.1.562.36.2.1.114.130.1.4 | OCTET STRING | read-only | If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below is present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. Usually, the resource remains available for service. The operationalState is almost always enabled. There is one exception where an operationalState of disabled is used in conjunction with degraded for a component which represents a rolled up view of a set of other components. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. The value migrating indicates that a software migration activation is in progress, making the component unavailable for other activities until the migration is complete. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8) migrating(9) |
| OCT mscAtmIfProceduralStatus | 1.3.6.1.4.1.562.36.2.1.114.130.1.5 | OCTET STRING | read-only | If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below is present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4) |
| OCT mscAtmIfControlStatus | 1.3.6.1.4.1.562.36.2.1.114.130.1.6 | OCTET STRING | read-only | If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below is present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3) |
| OCT mscAtmIfAlarmStatus | 1.3.6.1.4.1.562.36.2.1.114.130.1.7 | OCTET STRING | read-only | If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below is present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4) |
| INT mscAtmIfStandbyStatus | 1.3.6.1.4.1.562.36.2.1.114.130.1.8 | INTEGER | read-only | If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below is present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource. |
| INT mscAtmIfUnknownStatus | 1.3.6.1.4.1.562.36.2.1.114.130.1.9 | INTEGER | read-only | This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure. |
| mscAtmIfOperTable | 1.3.6.1.4.1.562.36.2.1.114.140 | not-accessible | This group contains operational attributes which show the status of the AtmIf component. | |
| mscAtmIfOperEntry | 1.3.6.1.4.1.562.36.2.1.114.140.1 | not-accessible | An entry in the mscAtmIfOperTable. | |
| G32 mscAtmIfTxCellMemoryAvailable | 1.3.6.1.4.1.562.36.2.1.114.140.1.1 | Gauge32 | read-only | This attribute is only valid for AtmIf's on ATM IP FPs. It is not displayed for AtmIf's on other card types. This attribute indicates the current amount of transmit cells available for this AtmIf. Transmit cell memory is the memory available for storing ATM cells to be transmitted by connections under this AtmIf. |
| G32 mscAtmIfTxCellMemoryCongestionState | 1.3.6.1.4.1.562.36.2.1.114.140.1.2 | Gauge32 | read-only | This attribute is only valid for AtmIf's on ATM IP FPs. It is not displayed for AtmIf's on other card types. This attribute indicates the congestion state of the transmit cell memory for this AtmIf. It indicates which txCellMemoryThreshold corresponds to the current value of txCellMemoryAvailable. The congestion state of memory is indicated by a numeric value ranging from 0 to 3. When memory is in a congested state 'x', only traffic with discard priority (DP) 'x' is definitely discarded. Traffic with DP = 'x' may be either queued or discarded depending on how close the value of txCellMemoryAvailable is to the next threshold as displayed in txCellMemoryThreshold. For example, CLP1 traffic is queued until the value indicated by txCellMemoryAvailable reaches the DP3 threshold. At that point, the CLP1 traffic is discarded. |
| INT mscAtmIfUnshapedTransmitQueueingOper | 1.3.6.1.4.1.562.36.2.1.114.140.1.10 | INTEGER | read-only | This attribute is HISTORICAL in P6.0. This attribute indicates the state of transmit queuing for unshaped connections under this AtmIf. A value of perVc indicates that any unshaped connections use per- VC queueing in the CQC. A value of common indicates that traffic for unshaped connections uses the common queue which corresponds to the atmServiceCategory for this connection. |
| mscAtmIfStatsTable | 1.3.6.1.4.1.562.36.2.1.114.150 | not-accessible | This group contains operational attributes which keep statistics about the behavior of the AtmIf component. | |
| mscAtmIfStatsEntry | 1.3.6.1.4.1.562.36.2.1.114.150.1 | not-accessible | An entry in the mscAtmIfStatsTable. | |
| NUM mscAtmIfTransmittedCells | 1.3.6.1.4.1.562.36.2.1.114.150.1.10 | PassportCounter64 | read-only | This attribute is renamed in P6.0 to txCell for naming compatibility with the Vcc and Vpc components. This attribute counts cells transmitted from the ATM interface. The counter is reset to zero when the component is created, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds the maximum value of (2**64)-1. |
| NUM mscAtmIfTxCell | 1.3.6.1.4.1.562.36.2.1.114.150.1.13 | PassportCounter64 | read-only | This attribute counts cells transmitted from the ATM interface. It does not include cells discarded due to congestion before transmit. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfTxCellClp | 1.3.6.1.4.1.562.36.2.1.114.150.1.14 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts cells transmitted from the ATM interface which have the CLP bit set to 1. This count is included in the txCell attribute. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfTxCellEfci | 1.3.6.1.4.1.562.36.2.1.114.150.1.15 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts cells transmitted from the ATM interface which have the EFCI bit set to 1. This count is included in the txCell attribute. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfTxCellDiscard | 1.3.6.1.4.1.562.36.2.1.114.150.1.16 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts cells discarded and not transmitted out the ATM interface. Since cells are discarded before they are transmitted, this count is not included in the txCell attribute. This count is independent of the txFrameDiscard attribute. Transmit cells are discarded due to transmit congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection's interface is disabled. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfTxCellDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.150.1.17 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts cells discarded and not transmitted out the ATM interface which have the CLP bit set to 1. Since cells are discarded before they are transmitted, this count is not included in the txCellClp attribute. This count is included in the txCellDiscard attribute, but it is independent of the txFrameDiscardClp attribute. Transmit cells are discarded due to transmit congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection's interface is disabled. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfTxFrameDiscard | 1.3.6.1.4.1.562.36.2.1.114.150.1.18 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts frames discarded and not transmitted out the ATM interface. This count is independent of txCellDiscard. Transmit frames are discarded due to congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection interface is disabled. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfTxFrameDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.150.1.19 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts frames which have at least one cell with the CLP bit set to 1, and have been discarded and not transmitted out the ATM interface. It is independent of the txCellDiscard attribute. This count is included in the txFrameDiscard attribute. Transmit frames are discarded due to congestion, Partial Packet Discard (PPD), Early Packet Discard (EPD), and Weighted Random Early Detection (W-RED) mechanisms, or when the connection interface is disabled. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfReceivedCells | 1.3.6.1.4.1.562.36.2.1.114.150.1.20 | PassportCounter64 | read-only | This attribute is renamed in P6.0 to rxCell for naming compatibility with the Vcc and Vpc component. This attribute counts valid cells received from the ATM interface. The counter is reset to zero when the component is created, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxCell | 1.3.6.1.4.1.562.36.2.1.114.150.1.23 | PassportCounter64 | read-only | This attribute counts valid cells received from the ATM interface. This count includes cells which may be subsequently discarded. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. On ATM IP FPs valid cells include cells that arrive on a VCC whose VPI.VCI cannot be identified. These cells are also counted under the droppedRxCell attribute. The value of this attribute on ATM IP FPs should be greater than or equal to the sum of droppedRxCell and all the VCC and VPC rxCell attributes under this interface. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxCellClp | 1.3.6.1.4.1.562.36.2.1.114.150.1.24 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts valid cells received from the ATM interface which have the CLP bit set to 1. This count includes cells which may be subsequently discarded. This count is included in the rxCell attribute. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxCellEfci | 1.3.6.1.4.1.562.36.2.1.114.150.1.25 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts valid cells received from the ATM interface which have the EFCI bit set to 1. This count includes cells which may be subsequently discarded. This count is included in the rxCell attribute. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxCellDiscard | 1.3.6.1.4.1.562.36.2.1.114.150.1.26 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts cells received from the ATM interface which have been discarded. This count is included in the rxCell attribute. This count includes cells discarded due to non-conformance with UPC, cells which are part of a frame which has been discarded due to an AAL5 frame reassembly error, cells which are discarded due to congestion, or cells which are received while the next hop connection to which the traffic is directed across the backplane is down. The next hop connection is the Vcc or Vpc identified by the nextHop attribute of the Nrp or Rp component. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxCellDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.150.1.27 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts valid cells received from the ATM interface which have the CLP bit set to 1, which have been discarded. This count is included in the rxCell and rxCellDiscard attributes. This count includes cells discarded due to non-conformance with UPC, cells which are part of a frame which has been discarded due to an AAL5 frame reassembly error, cells which are discarded due to congestion, or cells which are received while the next hop connection to which the traffic is directed across the backplane is down. The next hop connection is the Vcc or Vpc identified by the nextHop attribute of the Nrp or Rp component. This counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxFrameDiscard | 1.3.6.1.4.1.562.36.2.1.114.150.1.28 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts frames received from the ATM interface which have been discarded. This count includes the count of rxFrameDiscardClp and aal5RxErrors. It is independent of the rxCellDiscard attribute. This count includes frames discarded due to an AAL5 frame reassembly error, frames discarded due to early packet discard (EPD), and frames discarded due to processor (CPU) congestion. This attribute is applicable only for connections that reassemble incoming cells into frames. Connections which reassemble cells into frames have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; even though they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfRxFrameDiscardClp | 1.3.6.1.4.1.562.36.2.1.114.150.1.29 | PassportCounter64 | read-only | This attribute is not applicable and is not displayed on CQC-based ATM cards. This attribute counts frames received from the ATM interface which have been discarded and which have at least one cell with the CLP bit set to 1. This count is included in the rxFrameDiscard attribute. It is independent of the rxCellDiscardClp attribute. This count includes frames discarded due to an AAL5 frame reassembly error, frames discarded due to early packet discard (EPD), and frames discarded due to processor (CPU) congestion. This attribute is applicable only for connections that reassemble incoming cells into frames. Connections which reassemble cells into frames have a connectionPointType of connectionEndPoint. AAL1 connections are an exception to this rule; even though they have a connectionPointType of connectionEndPoint, they do not do adaptation at this point. The counter is reset to zero when the component is activated, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. |
| NUM mscAtmIfDroppedRxCells | 1.3.6.1.4.1.562.36.2.1.114.150.1.30 | PassportCounter64 | read-only | This attribute counts cells received from the interface that were dropped because they contained invalid VPI or VCI values, or dropped because they had no associated connection for the VPI or VCI. On ATM IP FPs this count is included in the rxCell count for the interface. Note that this attribute does not keep an exact count. Idle cells and unassigned cells are ignored without being counted as dropped cells. The counter is reset to zero when the component is created, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. The VPI and VCI of the last dropped cell are indicated in the attribute lastDroppedRxCellConnection. |
| NUM mscAtmIfLastDroppedRxCellConnection | 1.3.6.1.4.1.562.36.2.1.114.150.1.31 | IntegerSequence | read-only | This attribute indicates the VPI and VCI of the last cell that was dropped. Cells are dropped because they have no associated connection for the VPI and VCI. Dropped cells are counted in the attribute droppedRxCells. |
| C32 mscAtmIfAal5RxErrors | 1.3.6.1.4.1.562.36.2.1.114.150.1.32 | Counter32 | read-only | This attribute counts AAL5 frame reassembly errors which have occurred since the component was activated. These errors are either CRC errors or length errors, possibly caused by dropped cells.This attribute includes the count of AAL5 aborted frames. This count is included in the rxFrameDiscard count. The counter is reset to zero when the component is created, or when any critical attribute of the component is changed. The counter wraps to zero if it exceeds its maximum value of (2**64)-1. The VPI and VCI of the last connection which exhibited AAL5 reassembly errors are indicated in the attribute lastAal5ErrorConnection. |
| NUM mscAtmIfLastAal5RxErrorConnection | 1.3.6.1.4.1.562.36.2.1.114.150.1.33 | IntegerSequence | read-only | This attribute indicates the VPI and VCI of the last connection that exhibited AAL5 reassembly errors. These errors are counted in the attribute aal5RxErrors. |
| C32 mscAtmIfLrcFrameErrors | 1.3.6.1.4.1.562.36.2.1.114.150.1.34 | Counter32 | read-only | This attribute counts egress LRC frame errors on frames received across the bus. The likely cause of this is a hardware fault on either the sending or receiving card. The counter is reset to zero when the component is created, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. The VPI and VCI of the last connection which exhibited LRC errors are indicated in the attribute lastLrcFrameErrorConnection. |
| NUM mscAtmIfLastLrcFrameErrorConnection | 1.3.6.1.4.1.562.36.2.1.114.150.1.35 | IntegerSequence | read-only | This attribute indicates the VPI and VCI of the last connection that had LRC frame errors on frames received across the bus. These errors are counted in the attribute lrcFrameErrors. |
| C32 mscAtmIfAal5RxAborts | 1.3.6.1.4.1.562.36.2.1.114.150.1.40 | Counter32 | read-only | This attribute is not supported on any card type in Release 6.0 or earlier. This attribute counts AAL5 frame aborts which have been received since the component was activated. An AAL5 aborted frame is one in which the AAL5 frame length has been set to zero. This count is included in aal5RxErrors. The counter is reset to zero when the component is created, or when any critical attribute of the component is changed. The counter wraps to zero when it exceeds its maximum value of (2**64)-1. The VPI and VCI of the last connection which received AAL5 abort errors are displayed in the attribute lastAal5RxAbortConnection. |
| NUM mscAtmIfLastAal5RxAbortConnection | 1.3.6.1.4.1.562.36.2.1.114.150.1.50 | IntegerSequence | read-only | This attribute is not supported on any card type in Release 6.0 or earlier. This attribute indicates the VPI and VCI of the last connection that exhibited AAL5 aborts. These errors are counted in the attribute aal5RxAborts. |
| G32 mscAtmIfTxLinkUtilization | 1.3.6.1.4.1.562.36.2.1.114.150.1.59 | Gauge32 | read-only | This attribute indicates the current transmit interface utilization during the most recent minute, expressed as a percentage of the total bandwidth which can be carried by this ATM interface. The attribute is not supported for 4pOC12SmIrAtm and 4pOC12SmLrAtm cards when working in chanelized mode. |
| G32 mscAtmIfRxLinkUtilization | 1.3.6.1.4.1.562.36.2.1.114.150.1.60 | Gauge32 | read-only | This attribute indicates the current receive interface utilization during the most recent minute, expressed as a percentage of the total bandwidth which can be carried by this ATM interface. This attribute does not consider cells that are counted by the droppedRxCells attribute, nor idle cells, nor unassigned cells. The attribute is not supported for 4pOC12SmIrAtm and 4pOC12SmLrAtm cards when working in chanelized mode. |
| mscAtmIfTxCellMemoryThresholdTable | 1.3.6.1.4.1.562.36.2.1.114.441 | not-accessible | This attribute is only valid for AtmIf's on ATM IP FPs. It is not displayed for AtmIf's on other card types. This attribute indicates the transmit cell memory size and three discard thresholds for this AtmIf. Transmit cell memory is used for storing ATM cells to be transmitted by connections under this AtmIf. The first value indicates the the total transmit cell memory size. This is derived based upon the txCellMemoryThreshold 0 attribute of the Lp/x eng arc aqm/0 component and Lp/x eng arc aqm/0 Ov, and on the txCellMemory attribute of this AtmIf. When the txCellMemoryAvailable attribute decreases to the second value, the txCellMemoryCongestionState changes from 3 to 2. In congestion state 2, traffic with discard priority (DP) > 2 is discarded. This threshold is set approximately at 25 percent of the first value, the transmit cell memory size. When the txCellMemoryAvailable attribute decreases to the third value, the txCellMemoryCongestionState changes from 2 to 1. In congestion state 1, traffic with discard priority (DP) > 1 is discarded. This threshold is set approximately at 20 percent of the first value, the transmit cell memory size. When the txCellMemoryAvailable attribute decreases to the fourth value, the txCellMemoryCongestionState changes from 1 to 0. In congestion state 0, traffic with discard priority (DP) > 0 is discarded. This threshold is set approximately at 10 percent of the first value, the transmit cell memory size. The opposite effect occurs when the txCellMemoryAvailable attribute increases (txCellMemoryCongestionState changes from 0 to 3 accordingly). | |
| mscAtmIfTxCellMemoryThresholdEntry | 1.3.6.1.4.1.562.36.2.1.114.441.1 | not-accessible | An entry in the mscAtmIfTxCellMemoryThresholdTable. | |
| I32 mscAtmIfTxCellMemoryThresholdIndex | 1.3.6.1.4.1.562.36.2.1.114.441.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfTxCellMemoryThresholdTable specific index for the mscAtmIfTxCellMemoryThresholdTable. |
| U32 mscAtmIfTxCellMemoryThresholdValue | 1.3.6.1.4.1.562.36.2.1.114.441.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfTxCellMemoryThresholdTable. |
| mscAtmIfOpShapingRatesTable | 1.3.6.1.4.1.562.36.2.1.114.839 | not-accessible | This attribute displays the values of the 31 shaping rates currently in use at the interface. It is avector of 31 elements, each representing a shaping rate value. A rate entry of '0' means the entry is empty and can be used. This attribute is only valid for AtmIf's on APC-based FPs. It is not displayed for AtmIf's on other card types. | |
| mscAtmIfOpShapingRatesEntry | 1.3.6.1.4.1.562.36.2.1.114.839.1 | not-accessible | An entry in the mscAtmIfOpShapingRatesTable. | |
| I32 mscAtmIfOpShapingRatesIndex | 1.3.6.1.4.1.562.36.2.1.114.839.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfOpShapingRatesTable specific index for the mscAtmIfOpShapingRatesTable. |
| U32 mscAtmIfOpShapingRatesValue | 1.3.6.1.4.1.562.36.2.1.114.839.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfOpShapingRatesTable. |
| mscAtmIfShapeUsageTable | 1.3.6.1.4.1.562.36.2.1.114.840 | not-accessible | This attribute displays the number of VCs that currently use the 31 shaping rates. It is a vector of 31 elements each representing the number of VCs using the particular rate which is displayed with the same element index in the opShapingRates attribute. This attribute is only valid for AtmIf's on APC-based FPs. It is not displayed for AtmIf's on other card types. | |
| mscAtmIfShapeUsageEntry | 1.3.6.1.4.1.562.36.2.1.114.840.1 | not-accessible | An entry in the mscAtmIfShapeUsageTable. | |
| I32 mscAtmIfShapeUsageIndex | 1.3.6.1.4.1.562.36.2.1.114.840.1.1 | Integer32 | not-accessible | This variable represents the mscAtmIfShapeUsageTable specific index for the mscAtmIfShapeUsageTable. |
| U32 mscAtmIfShapeUsageValue | 1.3.6.1.4.1.562.36.2.1.114.840.1.2 | Unsigned32 | read-only | This variable represents an individual value for the mscAtmIfShapeUsageTable. |
| atmCoreMIB | 1.3.6.1.4.1.562.36.2.2.123 | |||
| atmCoreGroup | 1.3.6.1.4.1.562.36.2.2.123.1 | |||
| atmCoreGroupCB | 1.3.6.1.4.1.562.36.2.2.123.1.2 | |||
| atmCoreGroupCB02 | 1.3.6.1.4.1.562.36.2.2.123.1.2.3 | |||
| atmCoreGroupCB02A | 1.3.6.1.4.1.562.36.2.2.123.1.2.3.2 | |||
| atmCoreCapabilities | 1.3.6.1.4.1.562.36.2.2.123.3 | |||
| atmCoreCapabilitiesCB | 1.3.6.1.4.1.562.36.2.2.123.3.2 | |||
| atmCoreCapabilitiesCB02 | 1.3.6.1.4.1.562.36.2.2.123.3.2.3 | |||
| atmCoreCapabilitiesCB02A | 1.3.6.1.4.1.562.36.2.2.123.3.2.3.2 |
1,942 OIDs total — showing 1,731-1,942 (page 2 of 2)
« Prev Page 2 of 2