All MIBs › MOBANetClocksV2-MIB
Organization: Moser-Baer AG
Last Updated: 2014-06-17
Category: NTP
Description: Handles synchronization sources, status, and quality management for Moser-Baer network clocks.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MOBANetClocksV2-MIB?
MOBANetClocksV2-MIB is a vendor MIB from Moser-Baer AG (MOBATime) for managing network time synchronization equipment, specifically MOBATime slave clocks used in precision timekeeping systems. It exposes configuration and status data about time synchronization sources (e.g., NTP, GPS, DCF77) and the quality/accuracy of the clock signal being distributed. It is used to monitor the hardware/software status of the clock device itself, including which sync source is currently active and whether the clock has lost synchronization (a fault condition), directly relevant to detecting a slave clock drifting out of sync. It likely operates independently of general IETF time MIBs, being a MOBATime-specific device management module rather than an extension of a standard clock MIB. It is typically deployed in facilities requiring synchronized clock displays or time-stamped systems, such as transportation hubs, hospitals, and industrial plants, where MOBATime slave clocks receive time from a master clock/NTP source, and the MOBANetClocksV2-MIB MIB defines the objects used to confirm that synchronization is holding in these environments.
IPNetwork Monitor allows you to monitor SNMP objects defined in MOBANetClocksV2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- MOBATime (Moser-Baer) network slave clocks
Monitoring Examples
No specific object or table names were available in the source excerpt for this MIB, but an administrator would poll it to confirm which time synchronization source (e.g., GPS or NTP) a slave clock is currently using and check its lock/sync status, using a reported unsynchronized state as the signal that the clock is drifting and displays may show incorrect time.
What Can Be Monitored
- active time synchronization source
- synchronization/lock status
- clock signal quality/accuracy
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 | |
| enterprises |
From SNMPv2-TC
| DisplayString | |
| TEXTUAL-CONVENTION |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| mobatime | 1.3.6.1.4.1.13842 | |||
| mobaNetClocks | 1.3.6.1.4.1.13842.6 | |||
| mobaNetClocksV2 | 1.3.6.1.4.1.13842.6.2 | |||
| mbnscNet | 1.3.6.1.4.1.13842.6.2.1 | |||
| mbnscNetGen | 1.3.6.1.4.1.13842.6.2.1.1 | |||
| OCT mbnscNetGenMAC | 1.3.6.1.4.1.13842.6.2.1.1.1 | OCTET STRING | read-only | MAC-Address (xx xx xx xx xx xx) |
| INT mbnscNetGenIPMode | 1.3.6.1.4.1.13842.6.2.1.1.2 | INTEGER | read-write | IP Mode: 0: IPv4 and IPv6 1: IPv4 only 2: IPv6 only |
| STR mbnscNetGenIPNameserver | 1.3.6.1.4.1.13842.6.2.1.1.3 | DisplayString | read-write | IPv4 or IPv6 address (xxx.xxx.xxx.xxx or xxxx::xxxx:xxxx) of the nameserver |
| U32 mbnscNetGenTZClientPort | 1.3.6.1.4.1.13842.6.2.1.1.4 | Unsigned32 | read-write | Timezone client port. Default 65534 |
| U32 mbnscNetGenConfigPort | 1.3.6.1.4.1.13842.6.2.1.1.5 | Unsigned32 | read-write | Configuration port. Default 65532 |
| U32 mbnscNetGenSnmpMode | 1.3.6.1.4.1.13842.6.2.1.1.6 | Unsigned32 | read-only | SNMP mode disabled 0: SNMP enabled (default) 1: SNMP disabled |
| U32 mbnscNetGenMulticastMode | 1.3.6.1.4.1.13842.6.2.1.1.7 | Unsigned32 | read-write | Multicast mode disabled 0: Multicast enabled (default) 1: Multicast disabled |
| STR mbnscNetGenHostname | 1.3.6.1.4.1.13842.6.2.1.1.8 | DisplayString | read-write | Host name of the device |
| U32 mbnscNetGenCommMode | 1.3.6.1.4.1.13842.6.2.1.1.9 | Unsigned32 | read-only | Communication / synchronisation mode 0=unicast 1=multicast (only for digital clocks) |
| IP mbnscNetGenMCastGrpIP | 1.3.6.1.4.1.13842.6.2.1.1.10 | IpAddress | read-write | IP network address (xxx.xxx.xxx.xxx) of the multicast group IP e.g. 239.192.54.1 (only for digital clocks) |
| U32 mbnscNetGenConfigCmd | 1.3.6.1.4.1.13842.6.2.1.1.100 | Unsigned32 | read-write | Network configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscNetGenConfigChangedTime | 1.3.6.1.4.1.13842.6.2.1.1.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscNetIPv4 | 1.3.6.1.4.1.13842.6.2.1.2 | |||
| IP mbnscNetIPv4Addr | 1.3.6.1.4.1.13842.6.2.1.2.1 | IpAddress | read-write | IP network address (xxx.xxx.xxx.xxx) of the network slave clock |
| IP mbnscNetIPv4Mask | 1.3.6.1.4.1.13842.6.2.1.2.2 | IpAddress | read-write | IP subnet mask (xxx.xxx.xxx.xxx) |
| IP mbnscNetIPv4Gateway | 1.3.6.1.4.1.13842.6.2.1.2.3 | IpAddress | read-write | IP network address (xxx.xxx.xxx.xxx) for the gateway |
| U32 mbnscNetIPv4DHCPMode | 1.3.6.1.4.1.13842.6.2.1.2.4 | Unsigned32 | read-write | DHCP mode 0: DHCP disabled 1: DHCP enabled (default) |
| U32 mbnscNetIPv4ConfigCmd | 1.3.6.1.4.1.13842.6.2.1.2.100 | Unsigned32 | read-write | Network configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscNetIPv4ConfigChangedTime | 1.3.6.1.4.1.13842.6.2.1.2.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscNetIPv6 | 1.3.6.1.4.1.13842.6.2.1.3 | |||
| STR mbnscNetIPv6AddrLocal | 1.3.6.1.4.1.13842.6.2.1.3.1 | DisplayString | read-only | IP V6 link local network address (xxxx:xxxx::xxxx) |
| STR mbnscNetIPv6AddrAuto | 1.3.6.1.4.1.13842.6.2.1.3.2 | DisplayString | read-only | IP V6 network address by autoconfig (xxxx:xxxx::xxxx) |
| STR mbnscNetIPv6AddrDHCP | 1.3.6.1.4.1.13842.6.2.1.3.3 | DisplayString | read-only | IP V6 network address by DHCPv6 (xxxx:xxxx::xxxx) |
| MOB mbnscNetIPv6AddrFix | 1.3.6.1.4.1.13842.6.2.1.3.4 | MOBANetworkName | read-write | IP V6 network address manual set (xxxx:xxxx::xxxx) |
| U32 mbnscNetIPv6Prefix | 1.3.6.1.4.1.13842.6.2.1.3.5 | Unsigned32 | read-write | IPv6 subnet prefix for manual set IP address |
| STR mbnscNetIPv6Gateway | 1.3.6.1.4.1.13842.6.2.1.3.6 | DisplayString | read-only | IP V6 network address of gateway (next hop) (xxxx:xxxx::xxxx) |
| INT mbnscNetIPv6Config | 1.3.6.1.4.1.13842.6.2.1.3.7 | INTEGER | read-write | Mode of IPv6 adress configuration 0: auto and fixed 1: autoconfig only 2: DHCPv6 only 3: none |
| U32 mbnscNetIPv6ConfigCmd | 1.3.6.1.4.1.13842.6.2.1.3.100 | Unsigned32 | read-write | Network configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscNetIPv6ConfigChangedTime | 1.3.6.1.4.1.13842.6.2.1.3.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscTime | 1.3.6.1.4.1.13842.6.2.2 | |||
| STR mbnscTimeNTP1 | 1.3.6.1.4.1.13842.6.2.2.1 | DisplayString | read-write | String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information. |
| STR mbnscTimeNTP2 | 1.3.6.1.4.1.13842.6.2.2.2 | DisplayString | read-write | String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information. |
| STR mbnscTimeNTP3 | 1.3.6.1.4.1.13842.6.2.2.3 | DisplayString | read-write | String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information. |
| STR mbnscTimeNTP4 | 1.3.6.1.4.1.13842.6.2.2.4 | DisplayString | read-write | String with IPv4 or IPv6 address (192.168.3.4 or FD03:2345:2345:2345::231) or DNS name to get NTP time information. |
| STR mbnscTimeNTPcurrent | 1.3.6.1.4.1.13842.6.2.2.5 | DisplayString | read-only | IPv4 or IPv6 address of current NTP server |
| U32 mbnscTimeNTPpollIntervall | 1.3.6.1.4.1.13842.6.2.2.6 | Unsigned32 | read-write | NTP request intervall 10..999sec |
| U32 mbnscTimeDeviceTime | 1.3.6.1.4.1.13842.6.2.2.7 | Unsigned32 | read-only | Actual device time (UTC). Seconds since 1.1.1970 00:00:00 |
| I32 mbnscTimeLocOffset | 1.3.6.1.4.1.13842.6.2.2.8 | Integer32 | read-only | Offset to localt time in minutes (-720..720) |
| U32 mbnscTimeLastReception | 1.3.6.1.4.1.13842.6.2.2.9 | Unsigned32 | read-only | Last received time (UTC). Seconds since 1.1.1970 00:00:00 |
| U32 mbnscTimeConfigCmd | 1.3.6.1.4.1.13842.6.2.2.100 | Unsigned32 | read-write | Time configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscTimeConfigChangedTime | 1.3.6.1.4.1.13842.6.2.2.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscTimeZone | 1.3.6.1.4.1.13842.6.2.3 | |||
| I32 mbnscTimeZoneVersion | 1.3.6.1.4.1.13842.6.2.3.1 | Integer32 | read-only | Actual version internal time zone table |
| I32 mbnscTimeZoneNumber | 1.3.6.1.4.1.13842.6.2.3.2 | Integer32 | read-write | Time zone 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 254: automatic time zone - e.g. UTC 255: internal user defined time zone (SET only used for digital clocks) |
| OCT mbnscTimeZoneEntry1 | 1.3.6.1.4.1.13842.6.2.3.3 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| OCT mbnscTimeZoneEntry2 | 1.3.6.1.4.1.13842.6.2.3.4 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| OCT mbnscTimeZoneEntry3 | 1.3.6.1.4.1.13842.6.2.3.5 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| OCT mbnscTimeZoneEntry4 | 1.3.6.1.4.1.13842.6.2.3.6 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| OCT mbnscTimeZoneEntry5 | 1.3.6.1.4.1.13842.6.2.3.7 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| OCT mbnscTimeZoneEntry6 | 1.3.6.1.4.1.13842.6.2.3.8 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| OCT mbnscTimeZoneEntry7 | 1.3.6.1.4.1.13842.6.2.3.9 | OCTET STRING | read-only | Time Zone entry -> see special definition |
| U32 mbnscTimeZoneConfigCmd | 1.3.6.1.4.1.13842.6.2.3.100 | Unsigned32 | read-write | Time zone configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscTimeZoneConfigChangedTime | 1.3.6.1.4.1.13842.6.2.3.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscMode | 1.3.6.1.4.1.13842.6.2.4 | |||
| I32 mbnscModeSwitchInfo | 1.3.6.1.4.1.13842.6.2.4.1 | Integer32 | read-only | Current switch settings (only analogue movements) |
| STR mbnscModeDisplayBrightness | 1.3.6.1.4.1.13842.6.2.4.2 | DisplayString | read-write | Display brightness for digital clocks 1..30, A (Auto) |
| STR mbnscModeDisplayFormat | 1.3.6.1.4.1.13842.6.2.4.3 | DisplayString | read-write | Display format 12h/24h for digital clocks |
| STR mbnscModeDisplayAlternate | 1.3.6.1.4.1.13842.6.2.4.4 | DisplayString | read-write | Display alternating mode for digital clocks 1: time continuously 2: date cont. 3: temperature cont. (sequence 6 sec. time, 3 sec. date for ECO-DC) 4: stopwatch cont. (only DC clock) 5: sequence 6 sec. time, 3 sec. date (only DC clock) 6: sequence 8 sec. time, 3 sec. date, 3 sec. temperature (only DC clock) |
| STR mbnscModeNTP | 1.3.6.1.4.1.13842.6.2.4.5 | DisplayString | not-accessible | NTP synchronisation mode for digital clocks |
| STR mbnscModeIRlock | 1.3.6.1.4.1.13842.6.2.4.6 | DisplayString | read-write | IR autolock time for digital clocks (only DC clock) 1..60, U (autolock off) |
| STR mbnscModeTimeDispZeros | 1.3.6.1.4.1.13842.6.2.4.7 | DisplayString | read-write | Leading zeros time display for digital clocks (only DC clock) 1: time with leading zero 2: time without leading zero |
| STR mbnscModeDateDispZeros | 1.3.6.1.4.1.13842.6.2.4.8 | DisplayString | read-write | Leading zeros date display for digital clocks (only DC clock) 1: date with leading zero 2: date without leading zero |
| STR mbnscModeTempUnit | 1.3.6.1.4.1.13842.6.2.4.9 | DisplayString | read-write | Temperature unit for digital clocks (only DC clock) C: Celsius F: Fahrenheit |
| STR mbnscModeClockOpMode | 1.3.6.1.4.1.13842.6.2.4.10 | DisplayString | read-write | Operation mode for digital clocks (only DC clock) 0: normal mode 1: special mode 1 2: special mode 2 |
| STR mbnscModeNWParam | 1.3.6.1.4.1.13842.6.2.4.11 | DisplayString | not-accessible | Network parameter setting mode for digital clocks |
| STR mbnscModeDispDerating | 1.3.6.1.4.1.13842.6.2.4.12 | DisplayString | read-write | Display current deration setting for digital clocks (see service menu definition) |
| STR mbnscModeLightCorr | 1.3.6.1.4.1.13842.6.2.4.13 | DisplayString | read-write | Light measurement correction for digital clocks (see service menu definition) |
| mbnscAdditionalDigitalClockModes | 1.3.6.1.4.1.13842.6.2.4.30 | |||
| mbnscSensors | 1.3.6.1.4.1.13842.6.2.4.30.1 | |||
| STR mbnscSensorsTempActivation | 1.3.6.1.4.1.13842.6.2.4.30.1.1 | DisplayString | read-write | Temperature sensor activation 1: DS18B20 3: TME (only sensor 1) 4: TME (Sensors 1 and 2) |
| IP mbnscSensorsTemp1IPAddr | 1.3.6.1.4.1.13842.6.2.4.30.1.2 | IpAddress | read-write | IP network address (xxx.xxx.xxx.xxx) of the sensor 1 (SET only used for digital clocks) |
| IP mbnscSensorsTemp2IPAddr | 1.3.6.1.4.1.13842.6.2.4.30.1.3 | IpAddress | read-write | IP network address (xxx.xxx.xxx.xxx) of the sensor 2 (SET only used for digital clocks) |
| U32 mbnscSensorsConfigCmd | 1.3.6.1.4.1.13842.6.2.4.30.1.100 | Unsigned32 | read-write | Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscSensorsConfigChangedTime | 1.3.6.1.4.1.13842.6.2.4.30.1.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscDA | 1.3.6.1.4.1.13842.6.2.4.30.2 | |||
| STR mbnscDASecondCircleDisplay | 1.3.6.1.4.1.13842.6.2.4.30.2.1 | DisplayString | read-write | The second circle display mode 1: Accumulating ring of seconds marker 2: Take actual second from full shining circle step by step 3: Full shining circle, actual second off 4: Three shining seconds, the first is showing actual second 5: Two shining seconds, the first is showing actual second |
| U32 mbnscDAConfigCmd | 1.3.6.1.4.1.13842.6.2.4.30.2.100 | Unsigned32 | read-write | Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscDAConfigChangedTime | 1.3.6.1.4.1.13842.6.2.4.30.2.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscDK | 1.3.6.1.4.1.13842.6.2.4.30.3 | |||
| STR mbnscDKFirstLanguage | 1.3.6.1.4.1.13842.6.2.4.30.3.1 | DisplayString | read-write | First language selection 1: Czech 2: Slovak 3: English 4: German 5: ... (see manual for full language list) |
| STR mbnscDKSecondLanguage | 1.3.6.1.4.1.13842.6.2.4.30.3.2 | DisplayString | read-write | Second language selection 1: Czech 2: Slovak 3: English 4: German 5: ... (see manual for full language list) |
| STR mbnscDKThirdLanguage | 1.3.6.1.4.1.13842.6.2.4.30.3.3 | DisplayString | read-write | Third language selection 1: Czech 2: Slovak 3: English 4: German 5: ... (see manual for full language list) |
| STR mbnscDKTempUnitSecondLang | 1.3.6.1.4.1.13842.6.2.4.30.3.4 | DisplayString | read-write | Temperature units for second selected language C: Celsius F: Fahrenheit |
| STR mbnscDKTempUnitThirdLang | 1.3.6.1.4.1.13842.6.2.4.30.3.5 | DisplayString | read-write | Temperature units for third selected language C: Celsius F: Fahrenheit |
| STR mbnscDKAutoLangSwitchOver | 1.3.6.1.4.1.13842.6.2.4.30.3.6 | DisplayString | read-write | Language switch mode for automatic language switching over in one display alternating cycle A: all languages S: simple language |
| STR mbnscDKNumOfCharsForWeekday | 1.3.6.1.4.1.13842.6.2.4.30.3.7 | DisplayString | read-write | Number of characters used for weekday names 2: two characters 3: three characters |
| STR mbnscDKNamesFormatDisplay | 1.3.6.1.4.1.13842.6.2.4.30.3.8 | DisplayString | read-write | Weekday and month display format 1: first capital 2: all capitals |
| STR mbnscDKTemp1DescriptEnable | 1.3.6.1.4.1.13842.6.2.4.30.3.9 | DisplayString | read-write | Display of description for first measured temperature N/Y |
| STR mbnscDKTemp1Description | 1.3.6.1.4.1.13842.6.2.4.30.3.10 | DisplayString | read-write | Description text for first measured temperature |
| STR mbnscDKTemp2DescriptEnable | 1.3.6.1.4.1.13842.6.2.4.30.3.11 | DisplayString | read-write | Display of description for second measured temperature N/Y |
| STR mbnscDKTemp2Description | 1.3.6.1.4.1.13842.6.2.4.30.3.12 | DisplayString | read-write | Description text for second measured temperature |
| I32 mbnscDKWorldTimeZone1 | 1.3.6.1.4.1.13842.6.2.4.30.3.13 | Integer32 | read-write | Index of time zone for world time zone 1 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks) |
| STR mbnscDKWorldTimeZone1Description | 1.3.6.1.4.1.13842.6.2.4.30.3.14 | DisplayString | read-write | Description text for World time zone 1 |
| I32 mbnscDKWorldTimeZone2 | 1.3.6.1.4.1.13842.6.2.4.30.3.15 | Integer32 | read-write | Index of time zone for world time zone 2 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks) |
| STR mbnscDKWorldTimeZone2Description | 1.3.6.1.4.1.13842.6.2.4.30.3.16 | DisplayString | read-write | Description text for World time zone 2 |
| I32 mbnscDKWorldTimeZone3 | 1.3.6.1.4.1.13842.6.2.4.30.3.17 | Integer32 | read-write | Index of time zone for world time zone 3 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks) |
| STR mbnscDKWorldTimeZone3Description | 1.3.6.1.4.1.13842.6.2.4.30.3.18 | DisplayString | read-write | Description text for World time zone 3 |
| I32 mbnscDKWorldTimeZone4 | 1.3.6.1.4.1.13842.6.2.4.30.3.19 | Integer32 | read-write | Index of time zone for world time zone 4 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks) |
| STR mbnscDKWorldTimeZone4Description | 1.3.6.1.4.1.13842.6.2.4.30.3.20 | DisplayString | read-write | Description text for World time zone 4 |
| I32 mbnscDKWorldTimeZone5 | 1.3.6.1.4.1.13842.6.2.4.30.3.21 | Integer32 | read-write | Index of time zone for world time zone 5 0: UTC 1..64: See user manual, time zone table 65..128: user defined time zone 129..143: time zone server 1..15 255: none (SET only used for digital clocks) |
| STR mbnscDKWorldTimeZone5Description | 1.3.6.1.4.1.13842.6.2.4.30.3.22 | DisplayString | read-write | Description text for World time zone 5 |
| STR mbnscDKAutoTimeZoneSwitchOver | 1.3.6.1.4.1.13842.6.2.4.30.3.23 | DisplayString | read-write | World time switch mode for automatic time zone switching over in one display alternating cycle A: all world time zones S: simple world time zone |
| U32 mbnscDKConfigCmd | 1.3.6.1.4.1.13842.6.2.4.30.3.100 | Unsigned32 | read-write | Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscDKConfigChangedTime | 1.3.6.1.4.1.13842.6.2.4.30.3.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscAdditionalInterfaceModes | 1.3.6.1.4.1.13842.6.2.4.40 | |||
| mbnscNMI | 1.3.6.1.4.1.13842.6.2.4.40.1 | |||
| INT mbnscNMIDCFCurrentLoop | 1.3.6.1.4.1.13842.6.2.4.40.1.1 | INTEGER | read-write | Operation mode of the DCF77 current loop. 0: OFF 1: ON |
| INT mbnscNMILineDriver | 1.3.6.1.4.1.13842.6.2.4.40.1.2 | INTEGER | read-write | Operation mode of the line driver. 0: OFF 1: MOBALine 2: Active DCF |
| INT mbnscNMIMOBALineMode | 1.3.6.1.4.1.13842.6.2.4.40.1.3 | INTEGER | read-write | Operation mode of MOBALine. 0: normal operation 1: 12:00 mode, sideclocks shows 12:00 position 2: clock-id mode, sideclocks shows their ids if configured |
| INT mbnscNMIMOBALineMinuteHandMode | 1.3.6.1.4.1.13842.6.2.4.40.1.4 | INTEGER | read-write | Minute hand mode operation of MOBALine. 0: minute step mode 1: half minute step mode 2: continuous mode |
| INT mbnscNMIActiveDCFMode | 1.3.6.1.4.1.13842.6.2.4.40.1.5 | INTEGER | read-write | Operation mode of Active DCF. 1: Mode 1 2: Mode 2 3: Mode 3 4: Mode 4 5: Mode 5 6: Mode 6 |
| mbnscNMISideClockState | 1.3.6.1.4.1.13842.6.2.4.40.1.20 | |||
| INT mbnscNMISideClock1 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.1 | INTEGER | read-only | State of side clock 1 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock2 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.2 | INTEGER | read-only | State of side clock 2 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock3 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.3 | INTEGER | read-only | State of side clock 3 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock4 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.4 | INTEGER | read-only | State of side clock 4 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock5 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.5 | INTEGER | read-only | State of side clock 5 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock6 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.6 | INTEGER | read-only | State of side clock 6 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock7 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.7 | INTEGER | read-only | State of side clock 7 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock8 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.8 | INTEGER | read-only | State of side clock 8 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock9 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.9 | INTEGER | read-only | State of side clock 9 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock10 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.10 | INTEGER | read-only | State of side clock 10 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock11 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.11 | INTEGER | read-only | State of side clock 11 0: Clock not configured 3: Clock OK 5: Clock error |
| INT mbnscNMISideClock12 | 1.3.6.1.4.1.13842.6.2.4.40.1.20.12 | INTEGER | read-only | State of side clock 12 0: Clock not configured 3: Clock OK 5: Clock error |
| U32 mbnscNMIConfigCmd | 1.3.6.1.4.1.13842.6.2.4.40.1.100 | Unsigned32 | read-write | General configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscNMIConfigChangedTime | 1.3.6.1.4.1.13842.6.2.4.40.1.101 | TimeTicks | read-only | Time of the last configuration change. |
| U32 mbnscModeConfigCmd | 1.3.6.1.4.1.13842.6.2.4.100 | Unsigned32 | read-write | Mode configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscModeConfigChangedTime | 1.3.6.1.4.1.13842.6.2.4.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscGeneral | 1.3.6.1.4.1.13842.6.2.5 | |||
| I32 mbnscGeneralType | 1.3.6.1.4.1.13842.6.2.5.1 | Integer32 | read-only | Network slave clock type 1 Network Clock Interface NCI 2 Wireless Time Distribution WTD 868-T 3 NTP movement SEN 00 4 NTP movement NBU 190 5 Digital Clock ECO-DC 6 Digital Clock DC3 7 NTP movement SEN 40 8 NTP movement SAN 40 9 NTP digital clock DA 10 NTP calendar digital clock DK2 11 Network MOBALine Interface NMI 12 NTP clock TREND 13 NTP clock TREND double sided 14 NTP in- and outdoor digital clock DSC |
| STR mbnscGeneralName | 1.3.6.1.4.1.13842.6.2.5.2 | DisplayString | read-write | Device name (identifier) |
| STR mbnscGeneralFirmwareNumber | 1.3.6.1.4.1.13842.6.2.5.3 | DisplayString | read-only | Article number of the firmware. |
| STR mbnscGeneralFirmwareVer | 1.3.6.1.4.1.13842.6.2.5.4 | DisplayString | read-only | Firmware version. |
| MOB mbnscGeneralStatus | 1.3.6.1.4.1.13842.6.2.5.5 | MOBAFlags64 | read-only | Network slave clock status (64bit). Internal state of the network slave clock. Used for maintenance only. Bit 00 : time ok Bit 01 : 12h position Bit 02 : Reserved Bit 03 : Reserved Bit 04 : Reserved Bit 05 : Reserved Bit 06 : Reserved Bit 07 : Reserved Bit 08 : Reserved Bit 09 : Reserved Bit 10 : Reserved Bit 11 : Reserved Bit 12 : Reserved Bit 13 : Reserved Bit 14 : Reserved Bit 15 : Reserved Bit 16 : Reserved Bit 17 : Reserved Bit 18 : Reserved Bit 19 : Reserved Bit 20 : Reserved Bit 21 : Reserved Bit 22 : Reserved Bit 23 : Reserved Bit 24 : Reserved Bit 25 : Reserved Bit 26 : Reserved Bit 27 : Reserved Bit 28 : Reserved Bit 29 : Reserved Bit 30 : Reserved Bit 31 : Reserved Bit32..63 not used |
| MOB mbnscGeneralAlarms | 1.3.6.1.4.1.13842.6.2.5.6 | MOBAAlarm64 | read-only | Alarm state of the network slave clock Bit00=Synchronization Bit01=Power supply Bit02=Slave (cascade) Bit03=Illumination Bit04=Hands position (sec) Bit05=Hands position (m/h) Bit06=Restart Bit07=CommError Bit08=Time zone Bit09=Reserved Bit10=Reserved Bit11=Reserved Bit12=Reserved Bit13=Reserved Bit14=Reserved Bit15=Reserved Bit16=Reserved Bit17=Reserved Bit18=Reserved Bit19=Reserved Bit20=Reserved Bit21=Reserved Bit22=Reserved Bit23=Reserved Bit24=Reserved Bit25=Reserved Bit26=Reserved Bit27=Reserved Bit28=Reserved Bit29=Reserved Bit30=Reserved Bit31=Reserved Bit32..Bit63=Device type specific error |
| OCT mbnscGeneralSlaveInfo1 | 1.3.6.1.4.1.13842.6.2.5.7 | OCTET STRING | read-only | Info from slave 1 Byte 0..5 MAC Byte 6..11 Slave local time Byte 12..17 SW-number Byte 18..21 SW-version Byte 22 state Byte 23 reserved Byte 24 error Byte 25 reserved |
| OCT mbnscGeneralSlaveInfo2 | 1.3.6.1.4.1.13842.6.2.5.8 | OCTET STRING | read-only | Info from slave 2 Byte 0..5 MAC Byte 6..11 Slave local time Byte 12..17 SW-number Byte 18..21 SW-version Byte 22 state Byte 23 reserved Byte 24 error Byte 25 reserved |
| OCT mbnscGeneralSlaveInfo3 | 1.3.6.1.4.1.13842.6.2.5.9 | OCTET STRING | read-only | Info from slave 3 Byte 0..5 MAC Byte 6..11 Slave local time Byte 12..17 SW-number Byte 18..21 SW-version Byte 22 state Byte 23 reserved Byte 24 error Byte 25 reserved |
| U32 mbnscGeneralConfigCmd | 1.3.6.1.4.1.13842.6.2.5.100 | Unsigned32 | read-write | General configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscGeneralConfigChangedTime | 1.3.6.1.4.1.13842.6.2.5.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscSupervision | 1.3.6.1.4.1.13842.6.2.6 | |||
| STR mbnscSNMPManager1 | 1.3.6.1.4.1.13842.6.2.6.1 | DisplayString | read-write | String with IPv4 or IPv6 address (e.g 192.168.3.4 or FD03:2345:2345:2345::231) of the SNMP manager 1 |
| STR mbnscSNMPManager2 | 1.3.6.1.4.1.13842.6.2.6.2 | DisplayString | read-write | String with IPv4 or IPv6 address (e.g 192.168.3.4 or FD03:2345:2345:2345::231) of the SNMP manager 2 |
| U32 mbnscSNMPTrapAliveMsgInterval | 1.3.6.1.4.1.13842.6.2.6.3 | Unsigned32 | read-write | Time interval to send the alive message to the trap listener stations. 0: Alive message disabled >0: Alive message enabled Range: 1 ... 1440 minutes |
| U32 mbnscSNMPConfigCmd | 1.3.6.1.4.1.13842.6.2.6.100 | Unsigned32 | read-write | SNMP / supervision services configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| TIK mbnscSNMPConfigChangedTime | 1.3.6.1.4.1.13842.6.2.6.101 | TimeTicks | read-only | Time of the last configuration change. |
| mbnscCommand | 1.3.6.1.4.1.13842.6.2.7 | |||
| U32 mbnscCommand12Pos | 1.3.6.1.4.1.13842.6.2.7.1 | Unsigned32 | read-write | Mode of the analogue clock: 0=run, 1=12h position |
| U32 mbnscCommandSWReset | 1.3.6.1.4.1.13842.6.2.7.2 | Unsigned32 | read-write | Command SW reset if set to 1 |
| U32 mbnscCommandFactorySetting | 1.3.6.1.4.1.13842.6.2.7.3 | Unsigned32 | read-write | Restore factory settings if set to 1 |
| OCT mbnscCommandFirmwUpd | 1.3.6.1.4.1.13842.6.2.7.4 | OCTET STRING | read-only | Command to start FW update |
| I32 mbnscCommandExtContact | 1.3.6.1.4.1.13842.6.2.7.5 | Integer32 | read-only | Set external contact |
| U32 mbnscCommandConfigCmd | 1.3.6.1.4.1.13842.6.2.7.100 | Unsigned32 | read-write | SNMP / supervision services configuration changed command variable. 0: Not defined 1: SNMP has changed the configuration (possible restart of device) 2: SNMP requests to restore the old configuration |
| mbnscSnmpConfig | 1.3.6.1.4.1.13842.6.2.9 | |||
| mbnscSnmpCurrentAlarmInfo | 1.3.6.1.4.1.13842.6.2.9.1 | |||
| U32 mbnscTrapAlMsgErrorNr | 1.3.6.1.4.1.13842.6.2.9.1.1 | Unsigned32 | accessible-for-notify | Error number of the trap message. |
| U32 mbnscTrapAlMsgErrorState | 1.3.6.1.4.1.13842.6.2.9.1.2 | Unsigned32 | accessible-for-notify | Error state of the trap message. |
| U32 mbnscTrapAlMsgErrorTime | 1.3.6.1.4.1.13842.6.2.9.1.3 | Unsigned32 | accessible-for-notify | Error time of the trap message. Seconds since 1.1.1970 00:00:00 |
| mbnscTraps | 1.3.6.1.4.1.13842.6.2.10 | |||
| NTF mbnscTrapsAlarm | 1.3.6.1.4.1.13842.6.2.10.1 | Alarm trap with attached (binded variables) alarm information. mbnscTrapAlMsgErrorNr, mbnscTrapAlMsgErrorState, mbnscTrapAlMsgErrorTime | ||
| NTF mbnscTrapsAlive | 1.3.6.1.4.1.13842.6.2.10.2 | Device alive trap. Will be send in the configured interval. Attached are the variables mbnscGeneralStatus and mbnscGeneralAlarms. | ||
| mbnscMIB | 1.3.6.1.4.1.13842.6.100 | This mib definition is used for all MOBATime network slave clocks. | ||
| mbnscMIBCompliance | 1.3.6.1.4.1.13842.6.100.1 | |||
| mbnscMIBCompliances | 1.3.6.1.4.1.13842.6.100.1.1 | Please replace this text with your description. | ||
| mbnscMIBGroups | 1.3.6.1.4.1.13842.6.100.2 | |||
| mbnscAllNotifications | 1.3.6.1.4.1.13842.6.100.2.1 | This automatically created notification group contains all notifications that do not belong to any other NOTIFICATION-GROUP | ||
| mbnscGrpNBU190 | 1.3.6.1.4.1.13842.6.100.2.2 | All parameters used for NBU 190 movement | ||
| mbnscGrpSEN40 | 1.3.6.1.4.1.13842.6.100.2.3 | All parameters used for SEN 40 movement | ||
| mbnscGrpDC | 1.3.6.1.4.1.13842.6.100.2.4 | All parameters used for DC digital clock | ||
| mbnscGrpECODC | 1.3.6.1.4.1.13842.6.100.2.5 | All parameters used for ECO DC digital clock | ||
| mbnscGrpDA | 1.3.6.1.4.1.13842.6.100.2.6 | All parameters used for DA digital clock | ||
| mbnscGrpDK | 1.3.6.1.4.1.13842.6.100.2.7 | All parameters used for DK digital clock | ||
| mbnscGrpNMI | 1.3.6.1.4.1.13842.6.100.2.8 | All parameters used for Network-MOBALine-Interface NMI | ||
| mbnscGrpNotUsedParameters | 1.3.6.1.4.1.13842.6.100.2.100 | All parameters not used in oother groups |
RFC description
Manages Moser-Baer network clock synchronization sources, status, and quality.
Start monitoring MOBATime (Moser-Baer) network slave clock with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.