| OID symbolic | OID numeric | Type | Access | Description |
|---|
| swMldSnpMIB | 1.3.6.1.4.1.171.12.34 | | | The Structure of MLD snooping management for the
proprietary enterprise. |
| swMldSnpCtrl | 1.3.6.1.4.1.171.12.34.1 | | | |
| INT swMldSnoopingGlobalState | 1.3.6.1.4.1.171.12.34.1.1 | INTEGER | read-write | This object indicates if the MLD snooping capture function
is enabled or disabled. |
| INT swMldSnoopingMcstRTOnly | 1.3.6.1.4.1.171.12.34.1.2 | INTEGER | read-write | Specifies that the switch should forward all multicast traffic to a
multicast-enabled IPv6 router only. |
| swMldSnpInfo | 1.3.6.1.4.1.171.12.34.2 | | | |
| swMldSnpMgmt | 1.3.6.1.4.1.171.12.34.3 | | | |
| INT swMldSnoopingMaxSupportedVlans | 1.3.6.1.4.1.171.12.34.3.1 | INTEGER | read-only | Maximum number of VLANs in the MLD snooping table
(swMldSnoopingCtrlTable). |
| swMldSnoopingCtrlTable | 1.3.6.1.4.1.171.12.34.3.2 | | not-accessible | The table controls the VLAN's MLD function. Its scale depends
on the current VLAN state (swL2VlanInfoStatus). If the VLAN is in
disabled mode, there is only one entry in the table, with
index 1. If the VLAN is in Port-Base or 802.1q mode, the number of
entries can be up to 12, with an index range from 1 to 12. |
| swMldSnoopingCtrlEntry | 1.3.6.1.4.1.171.12.34.3.2.1 | | not-accessible | The entry in MLD control table (swMldSnoopingCtrlTable). The entry
is effective only when MLD capture switch
(swMldSnoopingGlobalState) is enabled. |
| INT swMldSnoopingCtrlVid | 1.3.6.1.4.1.171.12.34.3.2.1.1 | INTEGER | read-only | This object indicates the MLD control entry's VLAN ID. If the VLAN
is disabled, the VID is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the VID is
arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode,
the VID setting can vary from 1 to 4094 by the management user, and
the VID in each entry must be unique in the MLD Control Table. |
| INT swMldSnoopingQueryInterval | 1.3.6.1.4.1.171.12.34.3.2.1.2 | INTEGER | read-write | The frequency at which MLD Host-Query packets are
transmitted on this switch. |
| INT swMldSnoopingMaxResponseTime | 1.3.6.1.4.1.171.12.34.3.2.1.3 | INTEGER | read-write | The maximum query response time on this switch. |
| INT swMldSnoopingRobustness | 1.3.6.1.4.1.171.12.34.3.2.1.4 | INTEGER | read-write | The Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to have
a high loss, the Robustness Variable may be increased. MLD is
robust to (Robustness Variable-1) packet losses. |
| INT swMldSnoopingLastMemberQueryInterval | 1.3.6.1.4.1.171.12.34.3.2.1.5 | INTEGER | read-write | The Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages and is also the amount of time between
Group-Specific Query messages. |
| INT swMldSnoopingHostTimeout | 1.3.6.1.4.1.171.12.34.3.2.1.6 | INTEGER | read-write | The timer value for sending a MLD query packet when none were
sent by the host in the LAN. The timer works on a per-VLAN basis.
Our device will be activated to send a query message if the
timer has expired. |
| INT swMldSnoopingRouteTimeout | 1.3.6.1.4.1.171.12.34.3.2.1.7 | INTEGER | read-write | The Router Timeout is how long a host must wait after hearing
a Query before it sends any MLD messages. |
| INT swMldSnoopingDoneTimer | 1.3.6.1.4.1.171.12.34.3.2.1.8 | INTEGER | read-write | When a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries swMldSnoopingDoneTimer to the group
that is left. |
| INT swMldSnoopingQueryState | 1.3.6.1.4.1.171.12.34.3.2.1.9 | INTEGER | read-write | This object decides if the MLD query is enabled or disabled. |
| INT swMldSnoopingCurrentState | 1.3.6.1.4.1.171.12.34.3.2.1.10 | INTEGER | read-only | This object indicates the current MLD query state. |
| INT swMldSnoopingCtrlState | 1.3.6.1.4.1.171.12.34.3.2.1.11 | INTEGER | read-write | This object indicates the status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different for each of the following
values.
disable(2) - MLD function is disabled for this entry.
enable(3) - MLD function is enabled for this entry. |
| INT swMldSnoopingFastDoneState | 1.3.6.1.4.1.171.12.34.3.2.1.12 | INTEGER | read-write | This object indicates the fast_leave status of this entry.
other(1) - this entry is currently in use but the conditions under
which it will remain so are different for each of the following
values.
disable(2) - MLD fast-done function is disabled for this entry.
enable(3) - MLD fast-done function is enabled for this entry. |
| INT swMldSnoopingVersion | 1.3.6.1.4.1.171.12.34.3.2.1.13 | INTEGER | read-write | This object indicates the MLD version of this entry.
If the MLD version is configured with a lower version, the higher
version's MLD Report/Leave messages will be ignored. |
| swMldSnoopingGroupInfoTable | 1.3.6.1.4.1.171.12.34.3.3 | | not-accessible | The table contains the current MLD snooping information captured by
this device, provided that swMldSnoopingGlobalState and
swMldSnoopingCtrlState of associated VLAN entries are all enabled. Note
that the priority of MLD table entries is lower than the Filtering
Table, i.e. if there is a table hash collision between the
entries of the MLD Table and the Filtering Table inside the switch H/W
address table, then the Filtering Table entry overwrites the
colliding entry of the MLD snooping Table. |
| swMldSnoopingGroupInfoEntry | 1.3.6.1.4.1.171.12.34.3.3.1 | | not-accessible | Information about current MLD information which has been captured
by this device, provided that swMldSnoopingGlobalState and
swMldSnoopingCtrlState of the associated VLAN entries are all enabled. |
| INT swMldSnoopingGroupInfoVid | 1.3.6.1.4.1.171.12.34.3.3.1.1 | INTEGER | read-only | This object indicates the VID of an individual MLD table entry.
It shows the VID of MLD report information that has been captured
on the network. |
| ADR swMldSnoopingGroupInfoIpAddr | 1.3.6.1.4.1.171.12.34.3.3.1.2 | Ipv6Address | read-only | This object identifies the group IP address which is captured from
the MLD packet, on a per-VLAN basis. |
| MAC swMldSnoopingGroupInfoMacAddr | 1.3.6.1.4.1.171.12.34.3.3.1.3 | MacAddress | read-only | This object identifies the MAC addresses that correspond
to swMldSnoopingGroupInfoIpAddr, on a per-VLAN basis. |
| POR swMldSnoopingGroupInfoPortMap | 1.3.6.1.4.1.171.12.34.3.3.1.4 | PortList | read-only | This object indicates which ports belong to the same
multicast group, on a per-VLAN basis. Each multicast group has an
octet string to indicate the port map. The most significant
bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each
port of the switch is represented by a single bit within the
value of this object. If that bit has a value of '1' then that
port is included in the set of ports; the port is not included
if its bit has a value of '0'(Note that the setting of the bit
corresponding to the port from which a frame is received is
irrelevant). The 4 octets represent one unit port according to
its logical port. If the unit has less than 32 ports, other
ports will be set to 0. |
| INT swMldSnoopingGroupInfoReportCount | 1.3.6.1.4.1.171.12.34.3.3.1.5 | INTEGER | read-only | This object indicates how many report packets were received by our
device corresponding with the entry when the MLD function is enabled,
on a per-VLAN basis. |
| swMldSnpRouterPortsTable | 1.3.6.1.4.1.171.12.34.3.4 | | not-accessible | This table controls the VLAN's MLD router ports function. |
| swMldSnpRouterPortsEntry | 1.3.6.1.4.1.171.12.34.3.4.1 | | not-accessible | This entry shows the MLD router ports table (swMldSnoopingCtrlTable). |
| INT swMldSnpRouterPortsVid | 1.3.6.1.4.1.171.12.34.3.4.1.1 | INTEGER | read-only | This object indicates the MLD router ports entry VLAN ID. If a VLAN
is disabled, the VID is always 0 and cannot be changed by
management users. If a VLAN is in Port-Base mode, the VID is
arranged from 1 to 12, fixed form. If a VLAN is in 802.1q mode,
the VID setting can vary from 1 to 4094 by a management user, and
the VID in each entry must be unique in the MLD ports Table. |
| POR swMldSnpRouterStaticPortList | 1.3.6.1.4.1.171.12.34.3.4.1.2 | PortList | read-write | Displays router ports that have been statically configured. |
| POR swMldSnpRouterDynamicPortList | 1.3.6.1.4.1.171.12.34.3.4.1.3 | PortList | read-only | Displays router ports that have been dynamically configured. |
| POR swMldSnpRouterForbiddenPortList | 1.3.6.1.4.1.171.12.34.3.4.1.4 | PortList | read-write | Displays router ports that have been configured to be forbidden. |
| swMldSnoopingGroupTable | 1.3.6.1.4.1.171.12.34.3.5 | | not-accessible | The table contains the current MLD snooping information captured by
the device, provided that the swMldSnoopingGlobalState and
swMldSnoopingCtrlState of the associated VLAN entries are all enabled. Note
that the priority of the MLD table entries is lower than the Filtering
Table, i.e. if there is a table hash collision between the
entries of the MLD Table and the Filtering Table inside the switch H/W
address table, then the Filtering Table entry overwrites the
colliding entry of the MLD snooping Table. |
| swMldSnoopingGroupEntry | 1.3.6.1.4.1.171.12.34.3.5.1 | | not-accessible | Information about the current MLD information which has been captured by
the device, provided that swMldSnoopingGlobalState and
swMldSnoopingCtrlState of the associated VLAN entries are all enabled. |
| INT swMldSnoopingGroupVid | 1.3.6.1.4.1.171.12.34.3.5.1.1 | INTEGER | read-only | This object indicates the VID of the individual MLD table entry.
It shows the VID of the MLD report information captured on the
network. |
| ADR swMldSnoopingGroupGroupAddr | 1.3.6.1.4.1.171.12.34.3.5.1.2 | Ipv6Address | read-only | This object identifies the group IP address which has been captured from
the MLD packet, on a per-VLAN basis. |
| ADR swMldSnoopingGroupSourceAddr | 1.3.6.1.4.1.171.12.34.3.5.1.3 | Ipv6Address | read-only | This object identifies the source addresses which correspond
to swMldSnoopingGroupInfoGroupAddr, on a per-VLAN basis. |
| POR swMldSnoopingGroupIncludePortMap | 1.3.6.1.4.1.171.12.34.3.5.1.4 | PortList | read-only | This object indicates the port list under INCLUDE mode. |
| POR swMldSnoopingGroupExcludePortMap | 1.3.6.1.4.1.171.12.34.3.5.1.5 | PortList | read-only | This object indicates the port list under EXCLUDE mode. |
| swMldSnpForwardingTable | 1.3.6.1.4.1.171.12.34.3.6 | | not-accessible | This table contains the MLD Snooping forwarding information. |
| swMldSnpForwardingEntry | 1.3.6.1.4.1.171.12.34.3.6.1 | | not-accessible | A list of information about MLD Snooping forwarding. |
| INT swMldSnpVid | 1.3.6.1.4.1.171.12.34.3.6.1.1 | INTEGER | read-only | This object indicates the MLD Forwarding entry's VLAN ID. |
| ADR swMldSnpSourceIpAddr | 1.3.6.1.4.1.171.12.34.3.6.1.2 | Ipv6Address | read-only | This object identifies the forwarding IP address, which is captured from
the MLD packet. |
| ADR swMldSnpMutiGroupIpAddr | 1.3.6.1.4.1.171.12.34.3.6.1.3 | Ipv6Address | read-only | This object identifies the Multicast Group IP address, which is captured from
MLD packet. |
| POR swMldSnpForwardingListenPort | 1.3.6.1.4.1.171.12.34.3.6.1.4 | PortList | read-only | Indicates the MLD Snooping forwarding listen port. |
