JUNIPER-WX-STATUS-MIB

All MIBs › JUNIPER-WX-STATUS-MIB

Category: Technology: WAN Optimization, Vendor: Juniper

Description: Juniper Networks WX series MIB for monitoring operational status, hardware health, and service state of WAN optimization appliances.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is JUNIPER-WX-STATUS-MIB?

JUNIPER-WX-STATUS-MIB is a Juniper Networks-specific MIB for the WX series of WAN optimization/application acceleration appliances, exposing operational status and system information for these devices. It covers system identification (model, hardware and software version), counts and details of monitored/accelerated applications, and status of remote WX peer appliances participating in optimization tunnels. It is explicitly used to monitor hardware and software status: jnxWxGrpStatusSysHwVersion reports the hardware revision, jnxWxGrpStatusSysSwVersion reports the running software build, and the application and remote-WX tables reveal whether accelerated applications and paired remote appliances remain active and reachable. As a Juniper enterprise MIB it stands alone but is commonly polled alongside standard IF-MIB and SNMPv2-MIB objects for complete device visibility. It is typically deployed in WAN optimization environments where paired WX appliances sit at branch and data-center sites to accelerate application traffic. Engineers can download the JUNIPER-WX-STATUS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in JUNIPER-WX-STATUS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks WX series WAN optimization appliances

Monitoring Examples

An administrator polls jnxWxGrpStatusSysSwVersion and jnxWxGrpStatusSysHwVersion across a fleet to confirm all WX appliances are on matching firmware after an upgrade, flagging any unit still on an old build. Walking jnxWxGrpStatusAppTable/jnxWxGrpStatusAppEntry (keyed by jnxWxGrpStatusAppId and jnxWxGrpStatusAppName) against the expected jnxWxGrpStatusAppMonCount shows whether a monitored application definition has been dropped or misconfigured. The jnxWxGrpStatusRemoteWxTable lets an operator confirm all expected remote WX peers remain visible, revealing a lost WAN optimization tunnel if an entry unexpectedly disappears.

What Can Be Monitored

system hardware/software version
monitored/accelerated application count
per-application status
remote WX peer visibility and count

Imported Objects

From JUNIPER-WX-GLOBAL-MIB

jnxWxGrpStatus

OBJECT-IDENTITY

From SNMPv2-SMI

Integer32
OBJECT-TYPE

From SNMPv2-TC

DisplayString

How to Use in IPNetwork Monitor

Example using jnxWxGrpStatusAppMonCount OID:

Select a Juniper Networks WX series WAN acceleration appliance as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type jnxWxGrpStatusAppMonCount into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of applications currently being monitored by the WX WAN acceleration appliance. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the monitored-application count drops unexpectedly, which can indicate the appliance stopped classifying part of the traffic mix. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
jnxWxGrpStatusApp	1.3.6.1.4.1.2636.3.41.1.1.1.2			This group contains application status information.
jnxWxGrpStatusAppEntry	1.3.6.1.4.1.2636.3.41.1.1.1.2.2.1		not-accessible	A row in jnxWxGrpStatusAppTable.
I32 jnxWxGrpStatusAppId	1.3.6.1.4.1.2636.3.41.1.1.1.2.2.1.1	Integer32	not-accessible	The unique application ID.
I32 jnxWxGrpStatusAppMonCountEx	1.3.6.1.4.1.2636.3.41.1.1.1.2.1	Integer32	read-only	Number of applications currently being monitored.
STR jnxWxGrpStatusAppName	1.3.6.1.4.1.2636.3.41.1.1.1.2.2.1.2	DisplayString	read-only	The application name.
jnxWxGrpStatusAppTable	1.3.6.1.4.1.2636.3.41.1.1.1.2.2		not-accessible	This table displays the application level status. It contains information for only the applications currently being monitored.
INT jnxWxGrpStatusAppType	1.3.6.1.4.1.2636.3.41.1.1.1.2.2.1.3	INTEGER	read-only	The application type.
jnxWxGrpStatusRemoteWx	1.3.6.1.4.1.2636.3.41.1.1.1.3			This group contains remote WX status information.
jnxWxGrpStatusRemoteWxEntry	1.3.6.1.4.1.2636.3.41.1.1.1.3.2.1		not-accessible	A row in jnxWxGrpStatusRemoteWxTable.
I32 jnxWxGrpStatusRemoteWxId	1.3.6.1.4.1.2636.3.41.1.1.1.3.2.1.1	Integer32	not-accessible	The unique Remote WX ID.
I32 jnxWxGrpStatusRemoteWxMonCountEx	1.3.6.1.4.1.2636.3.41.1.1.1.3.1	Integer32	read-only	Number of remote WXs currently being monitored.
STR jnxWxGrpStatusRemoteWxName	1.3.6.1.4.1.2636.3.41.1.1.1.3.2.1.2	DisplayString	read-only	The remote WX name.
jnxWxGrpStatusRemoteWxTable	1.3.6.1.4.1.2636.3.41.1.1.1.3.2		not-accessible	This table displays the application level status. It contains information for only the applications currently being monitored.
INT jnxWxGrpStatusRemoteWxType	1.3.6.1.4.1.2636.3.41.1.1.1.3.2.1.3	INTEGER	read-only	The remote WX type.
jnxWxGrpStatusSys	1.3.6.1.4.1.2636.3.41.1.1.1.1			This group contains WX system status information.
STR jnxWxGrpStatusSysHwVersion	1.3.6.1.4.1.2636.3.41.1.1.1.1.3	DisplayString	read-only	The hardware version for this device.
INT jnxWxGrpStatusSysModel	1.3.6.1.4.1.2636.3.41.1.1.1.1.1	INTEGER	read-only	The device model number.
STR jnxWxGrpStatusSysSwVersion	1.3.6.1.4.1.2636.3.41.1.1.1.1.2	DisplayString	read-only	The software version for this device.

RFC description

Status monitoring MIB for Juniper WX series wide-area network optimization appliances.

Start monitoring Juniper Networks WX series WAN optimization appliance (system status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download JUNIPER-WX-STATUS-MIB