All MIBs › JUNIPER-WX-COMMON-MIB
Organization: Juniper Networks, Inc
Last Updated: 2003--0-9-
Category: Technology: WAN Optimization, Vendor: Juniper
Description:
Juniper Networks WX (WAN Acceleration) MIB providing common managed objects for WAN optimization appliance monitoring.
Imported Objects
| jnxWxCommonMib | OBJECT-IDENTITY |
| jnxWxModules | OBJECT-IDENTITY |
From JUNIPER-WX-GLOBAL-TC
| TcChassisType |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-IDENTITY | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| TruthValue |
What Is JUNIPER-WX-COMMON-MIB?
This is the base/common enterprise MIB shared across Juniper's WX Series WAN acceleration and optimization appliance family, providing shared managed-object definitions used by the other WX-specific MIBs. It exposes common definitions likely including product/system identity objects and shared OID roots and textual conventions used consistently across the WX product line, rather than device-specific runtime counters itself. Monitoring emphasis, as a foundational module, is on software/configuration identity (e.g. product model/version roots) leveraged by the companion JUNIPER-WX-MIB and JUNIPER-WX-EVENT-MIB rather than exposing hardware sensors directly. This module is an explicit dependency for the other WX-family MIBs, providing shared OID roots and conventions rather than standing alone. It is deployed alongside other WX MIBs on Juniper WX Series appliances performing WAN optimization/acceleration in branch and data-center links, where administrators typically load the JUNIPER-WX-COMMON-MIB into a MIB Browser alongside its companion modules.
IPNetwork Monitor allows you to monitor SNMP objects defined in JUNIPER-WX-COMMON-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper WX Series WAN acceleration appliance
Monitoring Examples
No object or table names were provided in the input data for this common/shared module. As a base MIB for the WX family, it primarily defines OID roots and shared conventions rather than pollable runtime tables, so no concrete monitoring scenario can be described without the actual MIB source.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| jnxWxCommonMibModule | 1.3.6.1.4.1.8239.1.1.3 | A MIB module containing definitions of managed objects implemented by all Juniper Networks' products. | ||
| jnxWxCommonConfMib | 1.3.6.1.4.1.8239.2.1.1 | Sub-tree for WAN Acceleration MIB conformance statements. | ||
| jnxWxCommonObjs | 1.3.6.1.4.1.8239.2.1.2 | Sub-tree for common MIB objects. | ||
| jnxWxSys | 1.3.6.1.4.1.8239.2.1.2.1 | Sub-tree for common system objects. | ||
| STR jnxWxSysSwVersion | 1.3.6.1.4.1.8239.2.1.2.1.1 | DisplayString | read-only | Full software version. The first two components of the full version are the major and minor versions. The third component indicates the maintenance release number and the fourth, the build number. |
| STR jnxWxSysHwVersion | 1.3.6.1.4.1.8239.2.1.2.1.2 | DisplayString | read-only | Hardware version of the unit. |
| STR jnxWxSysSerialNumber | 1.3.6.1.4.1.8239.2.1.2.1.3 | DisplayString | read-only | The serial number of the unit. If not available, an empty string is returned. |
| I32 jnxWxSysTimeZoneOffset | 1.3.6.1.4.1.8239.2.1.2.1.4 | Integer32 | read-only | The offset in seconds from UTC of the system's time zone. Values are negative for locations west of UTC and positive for locations east of UTC. |
| T/F jnxWxSysDaylightSaving | 1.3.6.1.4.1.8239.2.1.2.1.5 | TruthValue | read-only | Whether daylight savings are currently in effect for the system's time zone. |
| jnxWxChassis | 1.3.6.1.4.1.8239.2.1.2.2 | Sub-tree for common chassis information. | ||
| TCC jnxWxChassisType | 1.3.6.1.4.1.8239.2.1.2.2.1 | TcChassisType | read-only | Chassis type for this WX device. |
| jnxWxCommonEvents | 1.3.6.1.4.1.8239.2.1.3 | Sub-tree for common MIB events. | ||
| jnxWxCommonEventObjs | 1.3.6.1.4.1.8239.2.1.3.1 | Branch for objects meant only to be sent in event varbinds. | ||
| STR jnxWxCommonEventDescr | 1.3.6.1.4.1.8239.2.1.3.1.1 | DisplayString | accessible-for-notify | String that provides a textual description of the event. |
| jnxWxCommonEventEvents | 1.3.6.1.4.1.8239.2.1.3.2 | Branch for the events themselves. | ||
| jnxWxCommonEventEventsV2 | 1.3.6.1.4.1.8239.2.1.3.2.0 | Branch for SNMPv2 events. The OIDs for SNMPv2 events should have a zero as the next-to-last sub-identifier (as specified in RFC1902). | ||
| NTF jnxWxCommonEventInFailSafeMode | 1.3.6.1.4.1.8239.2.1.3.2.0.1 | This trap is sent when the device boots up in fail-safe mode. This can happen for one of the following reasons: o Fail-safe reboot was explicitly initiated by the user. o The device rebooted automatically too many times because of the failure of internal consistency checks or the failure of tests that verify proper operation of the device. | ||
| NTF jnxWxCommonEventPowerSupplyFailure | 1.3.6.1.4.1.8239.2.1.3.2.0.2 | One or more sources of power to the system has failed. A redundant power-supply has presumably taken over. NOTE: This trap is for future use. WX devices currently do not generate this trap. | ||
| NTF jnxWxCommonEventPowerSupplyOk | 1.3.6.1.4.1.8239.2.1.3.2.0.3 | One or more previously failed sources of power is now working normally. The transition to normal condition happened without the system having to be restarted. NOTE: This trap is for future use. WX devices currently do not generate this trap. | ||
| NTF jnxWxCommonEventLicenseExpired | 1.3.6.1.4.1.8239.2.1.3.2.0.4 | The license for the system expired. As a result, the system will switch over to and stay in pass-through mode. | ||
| NTF jnxWxCommonEventThruputLimitExceeded | 1.3.6.1.4.1.8239.2.1.3.2.0.5 | The throughput of traffic through the device has exceeded the limit for which it has been licensed. | ||
| NTF jnxWxCommonEventLicenseWillExpire | 1.3.6.1.4.1.8239.2.1.3.2.0.6 | The license for the system is about to expire shortly. When it eventually does expire, the system will switch over to and stay in pass-through mode. | ||
| NTF jnxWxCommonEventLoginFailure | 1.3.6.1.4.1.8239.2.1.3.2.0.7 | A user's login attempt via the console/ssh/web server failed due to incorrect username or password. | ||
| NTF jnxWxCommonEventFaultTolerantPassThrough | 1.3.6.1.4.1.8239.2.1.3.2.0.8 | An anomalous health condition was detected. It would have subsequently triggered hardware pass through mode followed by a reboot. | ||
| NTF jnxWxCommonEventFanFailure | 1.3.6.1.4.1.8239.2.1.3.2.0.9 | A cooling fan inside the device has failed. The 'jnxWxCommonEventDescr' object has the name of the fan that failed. This trap is currently unused | ||
| NTF jnxWxCommonEventFanSpeedVariation | 1.3.6.1.4.1.8239.2.1.3.2.0.10 | The speed of a cooling fan inside the device is either too low or too high. The 'jnxWxCommonEventDescr' object has the name of the fan that has the problem. This trap is currently unused. | ||
| NTF jnxWxCommonEventFanOk | 1.3.6.1.4.1.8239.2.1.3.2.0.11 | A cooling fan inside the device that had previously failed or whose speed variation was high is now working properly. The 'jnxWxCommonEventDescr' object has the name of the fan that has recovered. This trap is currently unused. | ||
| NTF jnxWxCommonEventInterfaceSpeedMismatch | 1.3.6.1.4.1.8239.2.1.3.2.0.12 | A mismatch is detected between the local and remote interface settings. This can happen due to a mismatch in the local and remote interface speed or mode. | ||
| NTF jnxWxCommonEventInterfaceSpeedOk | 1.3.6.1.4.1.8239.2.1.3.2.0.13 | A mismatch previously detected between the local and remote interface settings is now resolved. The local and remote interface speed and mode are matched. | ||
| NTF jnxWxCommonEventInterfaceDuplexMismatch | 1.3.6.1.4.1.8239.2.1.3.2.0.14 | A possible mismatch was detected between the duplex setting of either the local or remote interface and that of the device attached to that interface. The interface (local or remote) is identified by the 'jnxWxCommonEventDescr' object. Note that this notification is quite different from jnxWxCommonEventInterfaceSpeedMismatch, which compares the local and remote interfaces on the same WX device. | ||
| NTF jnxWxCommonEventIpsecSecurityAssociationAdded | 1.3.6.1.4.1.8239.2.1.3.2.0.15 | An IPSec security association has been negotiated and added to security association database. | ||
| NTF jnxWxCommonEventIpsecSecurityAssociationExpired | 1.3.6.1.4.1.8239.2.1.3.2.0.16 | An IPSec security association has been deleted from the security association database. | ||
| NTF jnxWxCommonEventIpsecSecurityAssociationDeleted | 1.3.6.1.4.1.8239.2.1.3.2.0.17 | An IPSec security association has been deleted from the security association database. |
RFC description
Juniper WX common MIB with managed objects implemented across all WX device platforms.
Start monitoring Juniper WX Series WAN acceleration appliance (shared definitions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.