All MIBs › JUNIPER-SOAM-PM-MIB › jnxSoamLmThresholdCfgEnable
jnxSoamLmThresholdCfgEnable
Module: JUNIPER-SOAM-PM-MIB
OID (symbolic): JUNIPER-SOAM-PM-MIB::jnxSoamLmThresholdCfgEnable
OID (numeric): 1.3.6.1.4.1.2636.3.78.1.2.5.1.2
Node type: OBJECT-TYPE
Type: Bits
Access: read-only
Description: A vector of bits that indicates the type of SOAM LM thresholds notifications that are enabled.
A bit set to '1' enables the specific SOAM LM threshold notification and when the specific counter is enabled and the threshold is crossed a notification is generated.
A bit set to '0' disables the specific SOAM LM threshold notification.
If a particular SOAM LM threshold is not supported the BIT value is set to '0'.
bJnxSoamLmMeasuredFlrForwardThreshold(0) Enables/disables measured frame loss forward ratio threshold notification. The notification is sent immediately when the jnxSoamLmMeasuredStatsForwardFlr value is greater than or equal to the threshold value. bJnxSoamLmMaxFlrForwardThreshold(1) Enables/disables maximum frame loss forward ratio threshold notification. The notification is sent immediately when the jnxSoamLmCurrentStatsForwardMaxFlr value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamLmAvgFlrForwardThreshold(2) Enables/disables average frame loss forward ratio threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamLmCurrentStatsForwardAvgFlr value is greater than or equal to the threshold value. bJnxSoamLmMeasuredFlrBackwardThreshold(3) Enables/disables measured frame loss backward ratio threshold notification. The notification is sent immediately when the jnxSoamLmMeasuredStatsBackwardFlr value is greater than or equal to the threshold value. bJnxSoamLmMaxFlrBackwardThreshold(4) Enables/disables maximum frame loss backward ratio threshold notification. The notification is sent immediately when the jnxSoamLmCurrentStatsBackwardMaxFlr value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamLmAvgFlrBackwardThreshold(5) Enables/disables average frame loss backward ratio threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamLmCurrentStatsBackwardAvgFlr value is greater than or equal to the threshold value.
What is jnxSoamLmThresholdCfgEnable?
A bitmap where each bit enables (1) or disables (0) generation of a notification for one specific SOAM LM threshold when the corresponding counter is enabled and crosses its configured limit; a bit forced to 0 means that particular threshold notification isn't supported on this device.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.2636.3.78.1.2.5.1.2 snmpwalk -v2c -c public <target> JUNIPER-SOAM-PM-MIB::jnxSoamLmThresholdCfgEnable
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.2636.3.78.1.2.5.1.2.1 snmpget -v2c -c public <target> JUNIPER-SOAM-PM-MIB::jnxSoamLmThresholdCfgEnable.1
Start monitoring Juniper router/switch, carrier Ethernet demarcation/aggregation device (SOAM performance monitoring) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the JUNIPER-SOAM-PM-MIB::jnxSoamLmThresholdCfgEnable OID value, configure state conditions and alerts, and monitor any Juniper router/switch, carrier Ethernet demarcation/aggregation device (SOAM performance monitoring) from a single console.
OID Breakdown
Upper-level ancestors (8 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.2636 | juniperMIB | JUNIPER-SMI |
| 1.3.6.1.4.1.2636.3 | jnxMibs | JUNIPER-SMI |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.2636.3.78 | jnxSoamPmMib | JUNIPER-SOAM-PM-MIB |
| 1.3.6.1.4.1.2636.3.78.1 | jnxSoamPmMibObjects | JUNIPER-SOAM-PM-MIB |
| 1.3.6.1.4.1.2636.3.78.1.2 | jnxSoamPmLmObjects | JUNIPER-SOAM-PM-MIB |
| 1.3.6.1.4.1.2636.3.78.1.2.5 | jnxSoamLmThresholdCfgTable | JUNIPER-SOAM-PM-MIB |
| 1.3.6.1.4.1.2636.3.78.1.2.5.1 | jnxSoamLmThresholdCfgEntry | JUNIPER-SOAM-PM-MIB |
| 1.3.6.1.4.1.2636.3.78.1.2.5.1.2 | jnxSoamLmThresholdCfgEnable | JUNIPER-SOAM-PM-MIB |