ISKRATEL-MSAN-MIB

All MIBs › ISKRATEL-MSAN-MIB

Organization: Iskratel

Last Updated: 2010-06-22

Category: Domain: DSL, Domain: DSL/xPON, Vendor: Iskratel

Description: Iskratel multi-service access node (MSAN) MIB providing SNMP objects for DSL, VoIP, and Ethernet service management on Iskratel platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ISKRATEL-MSAN-MIB?

ISKRATEL-MSAN-MIB is a vendor MIB from Iskratel for its multi-service access node (MSAN) platforms, which combine DSL, VoIP, and Ethernet access services in a single chassis for telecom access networks. It exposes configuration and status objects across these service types, covering line and port provisioning and service-level state for subscriber access lines. Its monitoring value spans both software/service status, such as DSL line sync state and VoIP call/registration status, and hardware port status, letting operators detect failed DSL lines, VoIP service outages, or Ethernet port faults on the access node. It is a vendor-specific MIB built on Iskratel's enterprise OID tree, typically used alongside standard IF-MIB and DSL-line MIBs for full access-node visibility. Typical deployment is telecom central-office or cabinet-mounted MSAN equipment delivering triple-play voice/data/video access to subscribers. Network engineers evaluating or troubleshooting this functionality can download the ISKRATEL-MSAN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ISKRATEL-MSAN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Iskratel multi-service access node (MSAN) platforms

Monitoring Examples

No sample objects were captured for this MIB; based on the module description, an operator would typically poll per-line DSL sync status and VoIP service state on the MSAN to identify a subscriber line that has lost DSL synchronization or a VoIP port that has dropped registration.

What Can Be Monitored

DSL line status/sync state
VoIP service/registration status
Ethernet port status
subscriber line provisioning

Imported Objects

From BRIDGE-MIB

dot1dBasePort

OBJECT-TYPE

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From INET-ADDRESS-MIB

InetAddress
InetAddressIPv4
InetAddressIPv6
InetAddressType

From Q-BRIDGE-MIB

VlanIndex
dot1qVlanIndex	OBJECT-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

BITS
Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

From VDSL-LINE-MIB

vdslLineConfProfileName

OBJECT-TYPE

From VDSL2-LINE-MIB

xdsl2LineAlarmConfTemplateEntry	OBJECT-TYPE
xdsl2LineConfTemplateEntry	OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
iskratel	1.3.6.1.4.1.1332
si2000	1.3.6.1.4.1.1332.1
products	1.3.6.1.4.1.1332.1.1
msan	1.3.6.1.4.1.1332.1.1.5			Description.
msanInfo	1.3.6.1.4.1.1332.1.1.5.1
msanShelfInfo	1.3.6.1.4.1.1332.1.1.5.1.1
OCT msanShelfId	1.3.6.1.4.1.1332.1.1.5.1.1.1	OCTET STRING	read-only	MSAN shelf ID.
OCT msanShelfType	1.3.6.1.4.1.1332.1.1.5.1.1.2	OCTET STRING	read-only	MSAN shelf type.
I32 msanShelfSize	1.3.6.1.4.1.1332.1.1.5.1.1.3	Integer32	read-only	Size of MSAN shelf (in number of slots).
msanBoardInfo	1.3.6.1.4.1.1332.1.1.5.1.2
msanBoardTable	1.3.6.1.4.1.1332.1.1.5.1.2.1		not-accessible	Description.
msanBoardEntry	1.3.6.1.4.1.1332.1.1.5.1.2.1.1		not-accessible	Description.
INT msanBoardNr	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.1	INTEGER	not-accessible	Unique identification of a board.
INT msanBoardParentNr	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.2	INTEGER	read-only	Unique identification of a parent board.
INT msanBoardPosition	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.3	INTEGER	read-only	Position of the board on the parent board.
OCT msanBoardType	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.4	OCTET STRING	read-only	Type of physical board (e.g. IDC, SGO, SFA, ...)
OCT msanBoardId	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.5	OCTET STRING	read-only	Name (actual identification) of a board.
OCT msanBoardSerialNr	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.6	OCTET STRING	read-only	Serial number of a board.
OCT msanBoardDescription	1.3.6.1.4.1.1332.1.1.5.1.2.1.1.7	OCTET STRING	read-write	Description of the board.
msanSwInfo	1.3.6.1.4.1.1332.1.1.5.1.3
OCT msanSwSteerVersion	1.3.6.1.4.1.1332.1.1.5.1.3.1	OCTET STRING	read-only	The unique steer code for this software.
OCT msanSwBuildDirectory	1.3.6.1.4.1.1332.1.1.5.1.3.2	OCTET STRING	read-only	The directory where software was build on.
OCT msanSwBuildTime	1.3.6.1.4.1.1332.1.1.5.1.3.3	OCTET STRING	read-only	The time when the software was built. (DateAndTime textual convention, from SNMPv2-TC)
OCT msanSwBranch	1.3.6.1.4.1.1332.1.1.5.1.3.4	OCTET STRING	read-only	The repository branch where the software was built from.
I32 msanSwBuildReference	1.3.6.1.4.1.1332.1.1.5.1.3.5	Integer32	read-only	The repository reference number of the software build branch.
OCT msanSwILVersion	1.3.6.1.4.1.1332.1.1.5.1.3.6	OCTET STRING	read-only	The unique IL steer code for this software.
OCT msanSwIpmiVersion	1.3.6.1.4.1.1332.1.1.5.1.3.7	OCTET STRING	read-only	The major version.minor version/IPMI version supported(HEX) number of the IPMI currently running on the switch. For example, if the major version was 1 and the minor version was 2, the format would be '1.2/0'.
OCT msanSwBspVersion	1.3.6.1.4.1.1332.1.1.5.1.3.8	OCTET STRING	read-only	The release.version/id number of the BSP software currently running on the switch. For example, if the release was 1 and the version was 2, the format would be '1.2/0'.
OCT msanSwCPLDVersion	1.3.6.1.4.1.1332.1.1.5.1.3.9	OCTET STRING	read-only	CPLD (Complex Programmable Logic Device) SW version
OCT msanReservePackage	1.3.6.1.4.1.1332.1.1.5.1.3.10	OCTET STRING	read-only	Name of the reserve package on disk if it exists.
msanSwComponentTable	1.3.6.1.4.1.1332.1.1.5.1.3.11		not-accessible	Description.
msanSwComponentEntry	1.3.6.1.4.1.1332.1.1.5.1.3.11.1		not-accessible	Description.
I32 msanSwComponentId	1.3.6.1.4.1.1332.1.1.5.1.3.11.1.1	Integer32	not-accessible	Unique index of SW component.
OCT msanSwComponentName	1.3.6.1.4.1.1332.1.1.5.1.3.11.1.2	OCTET STRING	read-only	Name of software component (e.g. ES, EV, EF, EA).
OCT msanSwComponentSteerVersion	1.3.6.1.4.1.1332.1.1.5.1.3.11.1.3	OCTET STRING	read-only	The unique steer code for this software component.
msanOtherInfo	1.3.6.1.4.1.1332.1.1.5.1.4
OCT msanSnmpSetErrorReason	1.3.6.1.4.1.1332.1.1.5.1.4.1	OCTET STRING	read-only	Last error description of SNMP set command.
msanAdditionalConf	1.3.6.1.4.1.1332.1.1.5.3
msanSystem	1.3.6.1.4.1.1332.1.1.5.3.1
OCT msanDateTime	1.3.6.1.4.1.1332.1.1.5.3.1.1	OCTET STRING	read-write	Board date and time in format: dd/MM/yyyy HH:mm:ss.
OCT msanShelfIdConf	1.3.6.1.4.1.1332.1.1.5.3.1.2	OCTET STRING	read-write	MSAN Shelf ID.
INT msanConfData	1.3.6.1.4.1.1332.1.1.5.3.1.3	INTEGER	read-only	Configured data saved or not saved to file on local file system.
OCT msanSwUpgrade	1.3.6.1.4.1.1332.1.1.5.3.1.4	OCTET STRING	read-write	msanSWUpgrade parameetr is used to start SW upgrade from external http or ftp server. User must set the next string value: = http\|ftp://\|[:]/[/] Procedure uses anonymous type of identification. If a non standard port is used, this port must be also specified in the repository URL.
OCT msanCliScriptCreate	1.3.6.1.4.1.1332.1.1.5.3.1.5	OCTET STRING	read-write	When set with a non-empty string, current configuration will be saved to script file with that name (name must end with .scr). If file already exists it's overwritten. On Get request this object will always return an empty string.
msanCliScriptTable	1.3.6.1.4.1.1332.1.1.5.3.1.6		not-accessible	Description.
msanCliScriptEntry	1.3.6.1.4.1.1332.1.1.5.3.1.6.1		not-accessible	Description.
OCT msanCliScriptName	1.3.6.1.4.1.1332.1.1.5.3.1.6.1.1	OCTET STRING	not-accessible	CLI script name
INT msanCliScriptApply	1.3.6.1.4.1.1332.1.1.5.3.1.6.1.2	INTEGER	read-write	When set to enable(1) selected selected CLI script is applied.
INT msanCliScriptApplyStatus	1.3.6.1.4.1.1332.1.1.5.3.1.6.1.3	INTEGER	read-only	Status of CLI script apply request
ROW msanCliScriptRowStatus	1.3.6.1.4.1.1332.1.1.5.3.1.6.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
OCT msanCliPrompt	1.3.6.1.4.1.1332.1.1.5.3.1.7	OCTET STRING	read-write	CLI prompt value.
I32 msanChassisId	1.3.6.1.4.1.1332.1.1.5.3.1.8	Integer32	read-write	MSAN Chassis ID.
msanSwBootPackageTable	1.3.6.1.4.1.1332.1.1.5.3.1.9		not-accessible	Description.
msanSwBootPackageEntry	1.3.6.1.4.1.1332.1.1.5.3.1.9.1		not-accessible	Description.
STR msanSwBootPackageName	1.3.6.1.4.1.1332.1.1.5.3.1.9.1.1	DisplayString	read-only	SW package name on local disk.
INT msanSwBootPackageStatus	1.3.6.1.4.1.1332.1.1.5.3.1.9.1.2	INTEGER	read-write	SW package status. You can set only nextActive(2) value. Other values are read-only.
msanSystemSwUpgrade	1.3.6.1.4.1.1332.1.1.5.3.1.10
INT msanSystemSwUpgradeStart	1.3.6.1.4.1.1332.1.1.5.3.1.10.1	INTEGER	read-write	Control of SW upgrade procedure. When set to enable(1) transfer of SW package from defined server is started.
INT msanSystemSwUpgradeStatus	1.3.6.1.4.1.1332.1.1.5.3.1.10.2	INTEGER	read-only	The SW upgrade status info.
IPt msanSystemSwUpgradeServerIpAddressType	1.3.6.1.4.1.1332.1.1.5.3.1.10.3	InetAddressType	read-write	Specifies the type of the upgrade server address: ipv4[1], ipv6[2].
IP msanSystemSwUpgradeServerIpAddress	1.3.6.1.4.1.1332.1.1.5.3.1.10.4	InetAddress	read-write	The remote SW upgrade server IP address.
STR msanSystemSwUpgradeServerDnsName	1.3.6.1.4.1.1332.1.1.5.3.1.10.5	DisplayString	read-write	The remote SW upgrade server dns name.
INT msanSystemSwUpgradeProtocol	1.3.6.1.4.1.1332.1.1.5.3.1.10.6	INTEGER	read-write	The SW upgrade protocol.
I32 msanSystemSwUpgradeProtocolPortId	1.3.6.1.4.1.1332.1.1.5.3.1.10.7	Integer32	read-write	The SW upgrade protocol port number. If value is set to -1, standard protocol number is used.
STR msanSystemSwUpgradeUserName	1.3.6.1.4.1.1332.1.1.5.3.1.10.8	DisplayString	read-write	The username used in SW upgrade protocol. When sftp upgrade protocol is used, username must be set.
STR msanSystemSwUpgradeUserPassword	1.3.6.1.4.1.1332.1.1.5.3.1.10.9	DisplayString	read-write	The user password used in SW upgrade protocol. When sftp upgrade protocol is used, username must be set.
STR msanSystemSwUpgradePath	1.3.6.1.4.1.1332.1.1.5.3.1.10.10	DisplayString	read-write	The path to the SW package location.
STR msanSystemSwUpgradePackageName	1.3.6.1.4.1.1332.1.1.5.3.1.10.11	DisplayString	read-write	The SW package name
msanSystemLogsUpload	1.3.6.1.4.1.1332.1.1.5.3.1.11
INT msanSystemLogsUploadStart	1.3.6.1.4.1.1332.1.1.5.3.1.11.1	INTEGER	read-write	Control of system logs upload procedure. When set to enable(1) transfer of file to defined server is started.
INT msanSystemLogsUploadStatus	1.3.6.1.4.1.1332.1.1.5.3.1.11.2	INTEGER	read-only	The system logs upload status info.
IPt msanSystemLogsUploadServerIpAddressType	1.3.6.1.4.1.1332.1.1.5.3.1.11.3	InetAddressType	read-write	Specifies the type of the system logs upload server address: ipv4[1], ipv6[2].
IP msanSystemLogsUploadServerIpAddress	1.3.6.1.4.1.1332.1.1.5.3.1.11.4	InetAddress	read-write	The remote system logs upload server IP address.
STR msanSystemLogsUploadServerDnsName	1.3.6.1.4.1.1332.1.1.5.3.1.11.5	DisplayString	read-write	The remote system logs upload server dns name.
INT msanSystemLogsUploadProtocol	1.3.6.1.4.1.1332.1.1.5.3.1.11.6	INTEGER	read-write	The system logs upload protocol.
I32 msanSystemLogsUploadProtocolPortId	1.3.6.1.4.1.1332.1.1.5.3.1.11.7	Integer32	read-write	The system logs upload protocol port number. If value is set to -1, standard protocol number is used.
STR msanSystemLogsUploadUserName	1.3.6.1.4.1.1332.1.1.5.3.1.11.8	DisplayString	read-write	The username used in system logs upload protocol. When sftp upgrade protocol is used, username must be set.
STR msanSystemLogsUploadUserPassword	1.3.6.1.4.1.1332.1.1.5.3.1.11.9	DisplayString	read-write	The user password used in system logs upload protocol. When sftp upgrade protocol is used, username must be set.
STR msanSystemLogsUploadPath	1.3.6.1.4.1.1332.1.1.5.3.1.11.10	DisplayString	read-write	The path to the system logs file location.
STR msanSystemLogsUploadFileName	1.3.6.1.4.1.1332.1.1.5.3.1.11.11	DisplayString	read-write	The system logs file name
msanProfiles	1.3.6.1.4.1.1332.1.1.5.3.3
msanVDSLProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.1		not-accessible	Description.
msanVDSLProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.1.1		not-accessible	Description.
INT msanVDSLProfileType	1.3.6.1.4.1.1332.1.1.5.3.3.1.1.1	INTEGER	read-write	Profile type: - other ~ none of the following - defaut ~ default profile - local ~ local configured profile type - global ~ global configured profile type
INT msanVDSL2LineProfile	1.3.6.1.4.1.1332.1.1.5.3.3.1.1.2	INTEGER	read-write	VDSL2 profile
msanServiceProfile	1.3.6.1.4.1.1332.1.1.5.3.3.2
msanServiceProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.2.1		not-accessible	Service Profile table
msanServiceProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1		not-accessible	Service Profile table entry.
OCT msanServiceProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.1	OCTET STRING	not-accessible	Name for service profile.
INT msanServiceProfileProtection	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanServiceProfileStatus = dynamic(2)
INT msanServiceProfileStatus	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.3	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
OCT msanServiceProfileServiceFlowProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.4	OCTET STRING	read-write	Index of used service flow profile (this profile must be set before), which indicates row in msanServiceFlowProfileTable. Empty string indicates that parameter has not been defined.
OCT msanServiceProfileMulticastProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.5	OCTET STRING	read-write	Index of used multicast profile (this profile must be set before), which indicates row in msanMulticastProfileTable. Empty string indicates that parameter has not been defined.
OCT msanServiceProfileVlanProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.6	OCTET STRING	read-write	Index of used vlan profile (this profile must be set before), which indicates row in msanVlanProfileTable. Empty string indicates that parameter has not been defined.
OCT msanServiceProfileL2cpProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.7	OCTET STRING	read-write	Index of used L2CP profile (this profile must be set before), which indicates row in msanL2cpProfileTable. Empty string indicates that parameter has not been defined.
OCT msanServiceProfileSecurityProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.8	OCTET STRING	read-write	Index of used security profile (this profile must be set before), which indicates row in msanSecurityProfileTable. Empty string indicates that parameter has not been defined.
I32 msanServiceProfileAtmVpi	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.9	Integer32	read-write	Virtual Path Identifier. A value of -1 indicates that parameter has not been defined.
I32 msanServiceProfileAtmVci	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.10	Integer32	read-write	Virtual Channel Identifier. A value of -1 indicates that parameter has not been defined.
INT msanServiceProfileDhcpRa	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.11	INTEGER	read-write	Dynamic Host Configuration Protocol Relay Agent. DHCP RA and PPPoE IA can not be included simultaneously.
INT msanServiceProfileDhcpRaTrustClients	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.12	INTEGER	read-write	DHCP RA Trust Clients. Effective only if DHCP-RA is in either allow-all or allow-client mode.
INT msanServiceProfileDhcpRaOpt82UnicastExtension	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.13	INTEGER	read-write	DHCP RA option82 unicast extension. Effective only if DHCP-RA is in either allow-all or allow-client mode.
INT msanServiceProfileDhcpRaOpt82Insert	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.14	INTEGER	read-write	DHCP Relay Agent Insert Option 82. Effective only if DHCP-RA is in either allow-all or allow-client mode.
OCT msanServiceProfileDhcpRaRemoteId	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.15	OCTET STRING	read-write	DHCP Relay Agent Remote Identification. Effective only if DHCP-RA is in either allow-all or allow-client mode.
U32 msanServiceProfileDhcpRaRateLimit	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.16	Unsigned32	read-write	Max rate for DHCP Relay Agent.
INT msanServiceProfilePppoeIA	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.17	INTEGER	read-write	Point-to-Point Protocol over Ethernet Intermediate Agent. DHCP RA and PPPoE IA can not be included simultaneously.
U32 msanServiceProfilePppoeIARateLimit	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.18	Unsigned32	read-write	Max rate for PPPoE IA.
OCT msanServiceProfileDescription	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.19	OCTET STRING	read-write	Attribute specifies text which describes the associated object.
ROW msanServiceProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.2.1.1.20	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported. Row can be activated only if msanServiceProfileServiceFlowProfileName is specified.
msanServicePortProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.2.2		not-accessible	A connection between service profiles and device ports
msanServicePortProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.2.2.1		not-accessible	Service Profile Port table entry.
ROW msanServicePortProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.2.2.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanServiceFlowProfile	1.3.6.1.4.1.1332.1.1.5.3.3.3
msanServiceFlowProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.3.1		not-accessible	Service Flow Profile table
msanServiceFlowProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1		not-accessible	Service Flow Profile table entry.
OCT msanServiceFlowProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.1	OCTET STRING	not-accessible	Service Flow Profile Name.
INT msanServiceFlowProfileProtection	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanServiceFlowProfileStatus = dynamic(2)
INT msanServiceFlowProfileStatus	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.3	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
INT msanServiceFlowProfileMatchUsAny	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.4	INTEGER	read-write	Match every upstream packet frame.
MAC msanServiceFlowProfileMatchUsMacDestAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.5	MacAddress	read-write	Match upstream packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined
MAC msanServiceFlowProfileMatchUsMacDestMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.6	MacAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchUsMacDestAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined
MAC msanServiceFlowProfileMatchUsMacSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.7	MacAddress	read-write	Match upstream packet frame with specified source MAC address. Empty string indicates that parameter has not been defined
MAC msanServiceFlowProfileMatchUsMacSrcMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.8	MacAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchUsMacSrcAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined
I32 msanServiceFlowProfileMatchUsCPcp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.9	Integer32	read-write	Match upstream packet frame with specified Customer PCP (Priority Code Point) - PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsSPcp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.10	Integer32	read-write	Match upstream packet frame with specified Service PCP (Priority Code Point). PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined.
INT msanServiceFlowProfileMatchUsVlanProfile	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.11	INTEGER	read-write	Match upstream packet frame with VLAN Id values from VLAN Service Profile (msanVlanProfileTable).
OCT msanServiceFlowProfileMatchUsCVlanIdRange	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.12	OCTET STRING	read-write	Match upstream packet frame with specified list (bitmask) of Customer VLAN Id. An empty string indicates that parameter has not been defined.
OCT msanServiceFlowProfileMatchUsSVlanIdRange	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.13	OCTET STRING	read-write	Match upstream packet frame with specified list (bitmask) of Service VLAN Id. An empty string indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsEthertype	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.14	Integer32	read-write	Match upstream packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsIpProtocol	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.15	Integer32	read-write	Match upstream packet frame with specified IP protocol value. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17
IP msanServiceFlowProfileMatchUsIpSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.16	IpAddress	read-write	Match upstream packet frame with specified source IP address. Empty string indicates that parameter has not been defined.
IP msanServiceFlowProfileMatchUsIpSrcMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.17	IpAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchUsIpSrcAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined
IP msanServiceFlowProfileMatchUsIpDestAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.18	IpAddress	read-write	Match upstream packet frame with specified destination IP address. Empty string indicates that parameter has not been defined.
IP msanServiceFlowProfileMatchUsIpDestMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.19	IpAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchUsIpDestAddr that is compared with upstream packet. Empty string indicates that parameter has not been defined
I32 msanServiceFlowProfileMatchUsIpDscp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.20	Integer32	read-write	Match upstream packet frame with specified CSC (Class Selector Code Point) = IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsIpCsc	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.21	Integer32	read-write	Match upstream packet frame with specified IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined.
INT msanServiceFlowProfileMatchUsIpDropPrecedence	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.22	INTEGER	read-write	Match upstream packet frame with specified Drop precedence two bits value: noDrop(0) -> 00 lowDrop(1) -> 01 mediumDrop(2) -> 10 highDrop(3) -> 11 A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsTcpSrcPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.23	Integer32	read-write	Match upstream packet frame with specified source TCP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsTcpDestPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.24	Integer32	read-write	Match upstream packet frame with specified destination TCP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsUdpSrcPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.25	Integer32	read-write	Match upstream packet frame with specified source UDP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchUsUdpDstPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.26	Integer32	read-write	Match upstream packet frame with specified destination UDP port number. A value of -1 indicates that parameter has not been defined.
INT msanServiceFlowProfileMatchDsAny	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.27	INTEGER	read-write	Match every downstream packet frame.
MAC msanServiceFlowProfileMatchDsMacDestAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.28	MacAddress	read-write	Match downstream packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined
MAC msanServiceFlowProfileMatchDsMacDestMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.29	MacAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchDsMacDestAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined
MAC msanServiceFlowProfileMatchDsMacSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.30	MacAddress	read-write	Match downstream packet frame with specified source MAC address. Empty string indicates that parameter has not been defined
MAC msanServiceFlowProfileMatchDsMacSrcMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.31	MacAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchDsMacSrcAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined
I32 msanServiceFlowProfileMatchDsCPcp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.32	Integer32	read-write	Match downstream packet frame with specified Customer PCP (Priority Code Point) - PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsSPcp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.33	Integer32	read-write	Match downstream packet frame with specified Service PCP (Priority Code Point). PCP is also known as class of service (CoS) bits. A value of -1 indicates that parameter has not been defined.
INT msanServiceFlowProfileMatchDsVlanProfile	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.34	INTEGER	read-write	Match downstream packet frame with VLAN Id values from VLAN Service Profile (msanVlanProfileTable).
OCT msanServiceFlowProfileMatchDsCVlanIdRange	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.35	OCTET STRING	read-write	Match downstream packet frame with specified list (bitmask) of Customer VLAN Id. An emptya string indicates that parameter has not been defined.
OCT msanServiceFlowProfileMatchDsSVlanIdRange	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.36	OCTET STRING	read-write	Match downstream packet frame with specified list (bitmask) of Service VLAN Id. An empty string indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsEthertype	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.37	Integer32	read-write	Match downstream packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsIpProtocol	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.38	Integer32	read-write	Match downstream packet frame with specified IP protocol value. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17
IP msanServiceFlowProfileMatchDsIpSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.39	IpAddress	read-write	Match downstream packet frame with specified source IP address. Empty string indicates that parameter has not been defined.
IP msanServiceFlowProfileMatchDsIpSrcMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.40	IpAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchDsIpSrcAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined
IP msanServiceFlowProfileMatchDsIpDestAddr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.41	IpAddress	read-write	Match downstream packet frame with specified destination IP address. Empty string indicates that parameter has not been defined.
IP msanServiceFlowProfileMatchDsIpDestMask	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.42	IpAddress	read-write	This mask value identifies the portion of msanServiceFlowProfileMatchDsIpDestAddr that is compared with downstream packet. Empty string indicates that parameter has not been defined
I32 msanServiceFlowProfileMatchDsIpDscp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.43	Integer32	read-write	Match downstream packet frame with specified IP DSCP value. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsIpCsc	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.44	Integer32	read-write	Match downstream packet frame with specified CSC (Class Selector Code Point) = IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined.
INT msanServiceFlowProfileMatchDsIpDropPrecedence	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.45	INTEGER	read-write	Match downstream packet frame with specified Drop precedence two bits value: noDrop(0) -> 00 lowDrop(1) -> 01 mediumDrop(2) -> 10 highDrop(3) -> 11 A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsTcpSrcPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.46	Integer32	read-write	Match downstream packet frame with specified source TCP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsTcpDestPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.47	Integer32	read-write	Match downstream packet frame with specified destination TCP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsUdpSrcPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.48	Integer32	read-write	Match downstream packet frame with specified source UDP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileMatchDsUdpDstPort	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.49	Integer32	read-write	Match downstream packet frame with specified destination UDP port number. A value of -1 indicates that parameter has not been defined.
I32 msanServiceFlowProfileUsCdr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.50	Integer32	read-write	Upstream committed data rate (E-CDR) in kbps (0 1000000).
I32 msanServiceFlowProfileUsCdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.51	Integer32	read-write	Upstream committed data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInCdr value.
I32 msanServiceFlowProfileUsPdr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.52	Integer32	read-write	Upstream peak data rate (E-PDR) in kbps (0 1000000).
I32 msanServiceFlowProfileUsPdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.53	Integer32	read-write	Upstream peak data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInPdr value.
INT msanServiceFlowProfileUsMarkPcp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.54	INTEGER	read-write	Type of upstrem PCP marking. If set to userValue(3), parameter msanServiceFlowProfileUsMarkPcpValue is used. A value of none(1) indicates that parameter has not been defined
INT msanServiceFlowProfileUsMarkPcpValue	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.55	INTEGER	read-write	Mark upstream packets with specified PCP (Priority Code Point) value (0-7) = CoS. A value of -1 indicates that parameter has not been defined
INT msanServiceFlowProfileUsMarkDscp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.56	INTEGER	read-write	Type of upstrem DSCP marking. If set to userValue(3), parameter msanServiceFlowProfileUsMarkDscpValue is used. A value of none(1) indicates that parameter has not been defined
INT msanServiceFlowProfileUsMarkDscpValue	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.57	INTEGER	read-write	Mark upstream packets with specified DSCP (Diffserv Code Point) value (0-63). A value of -1 indicates that parameter has not been defined
I32 msanServiceFlowProfileDsCdr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.58	Integer32	read-write	Downstream committed data rate (E-CDR) in kbps (0 1000000).
I32 msanServiceFlowProfileDsCdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.59	Integer32	read-write	Downstream committed data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value.
I32 msanServiceFlowProfileDsPdr	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.60	Integer32	read-write	Downstream peak data rate (E-PDR) in kbps (0 1000000).
I32 msanServiceFlowProfileDsPdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.61	Integer32	read-write	Downstream peak data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value.
INT msanServiceFlowProfileDsMarkPcp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.62	INTEGER	read-write	Type of downstream PCP marking. If set to userValue(3), parameter msanServiceFlowProfileDsMarkPcpValue is used. A value of none(1) indicates that parameter has not been defined
INT msanServiceFlowProfileDsMarkPcpValue	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.63	INTEGER	read-write	Mark downstream packets with specified PCP (Priority Code Point) value (0-7) = CoS. A value of -1 indicates that parameter has not been defined
INT msanServiceFlowProfileDsMarkDscp	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.64	INTEGER	read-write	Type of downstrem DSCP marking. If set to userValue(3), parameter msanServiceFlowProfileDsMarkDscpValue is used. A value of none(1) indicates that parameter has not been defined
INT msanServiceFlowProfileDsMarkDscpValue	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.65	INTEGER	read-write	Mark downstream packets with specified DSCP (Diffserv Code Point) value (0-63). A value of -1 indicates that parameter has not been defined
INT msanServiceFlowProfileDsQueuingPriority	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.66	INTEGER	read-write	Queuing Priority of Service Flow Profile.
INT msanServiceFlowProfileDsSchedulingMode	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.67	INTEGER	read-write	Scheduling Mode
OCT msanServiceFlowProfileDescription	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.68	OCTET STRING	read-write	Attribute specifies text which describes the associated object.
ROW msanServiceFlowProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.3.1.1.69	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanVlanProfile	1.3.6.1.4.1.1332.1.1.5.3.3.4
msanVlanProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.4.1		not-accessible	Vlan Profile table
msanVlanProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1		not-accessible	Vlan Profile table entry.
OCT msanVlanProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.1	OCTET STRING	not-accessible	Name for the VLAN profile.
INT msanVlanProfileProtection	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanVlanProfileStatus = dynamic(2)
INT msanVlanProfileStatus	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.3	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
OCT msanVlanProfileCVid	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.4	OCTET STRING	read-write	Customer VLANs Identification (bit mask).
I32 msanVlanProfileCVidNative	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.5	Integer32	read-write	Nativ C-VLAN Id. A value of -1 indicates that parameter has not been defined.
I32 msanVlanProfileCVidRemark	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.6	Integer32	read-write	Remark C-VLAN Id. A value of -1 indicates that parameter has not been defined.
I32 msanVlanProfileSVid	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.7	Integer32	read-write	S-VLAN Id. A value of -1 indicates that parameter has not been defined.
I32 msanVlanProfileSEtherType	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.8	Integer32	read-write	Ether Type value.
OCT msanVlanProfileDescription	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.10	OCTET STRING	read-write	Attribute specifies text which describes the associated object.
ROW msanVlanProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.11	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
INT msanVlanProfileNetworkPortCTag	1.3.6.1.4.1.1332.1.1.5.3.3.4.1.1.12	INTEGER	read-write	Usage of C-VLAN tag on network port. If assigned as notUse(2) in upstream direction, C-VLAN tag is removed.
msanVlanPortProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.4.2		not-accessible	A connection between VLAN profiles and device ports
msanVlanPortProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.4.2.1		not-accessible	Service Profile Port table entry.
ROW msanVlanPortProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.4.2.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastProfile	1.3.6.1.4.1.1332.1.1.5.3.3.5
msanMulticastProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.5.1		not-accessible	Multicast Profile table
msanMulticastProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1		not-accessible	Multicast Profile table entry.
OCT msanMulticastProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.1	OCTET STRING	not-accessible	Name for the Multicast profile.
INT msanMulticastProfileProtection	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanMulticastProfileStatus = dynamic(2)
INT msanMulticastProfileStatus	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.3	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
INT msanMulticastProfileIgmpSnooping	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.4	INTEGER	read-write	IGMP snnoping
INT msanMulticastProfileIgmpSnoopingFastLeave	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.5	INTEGER	read-write	IGMP Snooping Fast Leave.
INT msanMulticastProfileIgmpSnoopingSuppression	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.6	INTEGER	read-write	IGMP Snooping Suppression.
INT msanMulticastProfileIgmpProxy	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.7	INTEGER	read-write	IGMP proxy.
IP msanMulticastProfileIgmpProxyIpAddress	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.8	IpAddress	read-write	IGMP proxy IP address.
INT msanMulticastProfileIgmpFiltering	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.9	INTEGER	read-write	IGMP filtering.
U32 msanMulticastProfileMulticastGroupLimit	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.10	Unsigned32	read-write	Multicast group limit. A value of 0 indicates not limit.
INT msanMulticastProfileMvr	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.11	INTEGER	read-write	Multicast VLAN Registration.
OCT msanMulticastProfileDescription	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.12	OCTET STRING	read-write	Attribute specifies text which describes the associated object.
ROW msanMulticastProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.5.1.1.13	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastProfileStaticGroupTable	1.3.6.1.4.1.1332.1.1.5.3.3.5.2		not-accessible	Connection between multicast_profile and multicast_static_group table
msanMulticastProfileStaticGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.3.5.2.1		not-accessible	Multicast Profile Group table entry.
IP msanMulticastProfileStaticGroupIpAddr	1.3.6.1.4.1.1332.1.1.5.3.3.5.2.1.1	IpAddress	not-accessible	Description.
ROW msanMulticastProfileStaticGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.5.2.1.9	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanSecurityProfile	1.3.6.1.4.1.1332.1.1.5.3.3.6
msanSecurityProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.6.1		not-accessible	Security Profile table
msanSecurityProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1		not-accessible	Security Profile table entry.
OCT msanSecurityProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.1	OCTET STRING	not-accessible	Name of the security profile.
INT msanSecurityProfileProtection	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanSecurityProfileStatus = dynamic(2)
INT msanSecurityProfileStatus	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.3	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
INT msanSecurityProfileProtectedPort	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.4	INTEGER	read-write	Security profile protected port
INT msanSecurityProfileMacSg	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.5	INTEGER	read-write	Mac source guard
U32 msanSecurityProfileMacLimit	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.6	Unsigned32	read-write	MAC limit A value of 0 indicates that parameter has not been defined.
INT msanSecurityProfilePortSecurity	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.7	INTEGER	read-write	Port security
INT msanSecurityProfileIpSg	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.8	INTEGER	read-write	IP source guard
U32 msanSecurityProfileIpSgBindingLimit	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.9	Unsigned32	read-write	IP source guard binding limit.
INT msanSecurityProfileIpSgFilteringMode	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.10	INTEGER	read-write	IP source guard filtering mode
INT msanSecurityProfileArpInspec	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.12	INTEGER	read-write	Dynamic ARP inspection
INT msanSecurityProfileMacForward	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.13	INTEGER	read-write	MAC forwarding
OCT msanSecurityProfileDescription	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.14	OCTET STRING	read-write	Attribute specifies text which describes the associated object.
ROW msanSecurityProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.6.1.1.15	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanSecurityAclProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.6.3		not-accessible	A connection between security profiles and access lists
msanSecurityAclProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1		not-accessible	Service Profile Port table entry.
INT msanSecurityAclProfileAclDirection	1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.1	INTEGER	not-accessible	The direction to which this ACL instance applies.
U32 msanSecurityAclProfileSequence	1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.2	Unsigned32	not-accessible	The relative evaluation sequence of this ACL for this interface and direction. When multiple ACLs are allowed for a given interface and direction, the sequence number determines the order in which the list of ACLs are evaluated, with lower sequence numbers given higher precedence. The sequence number value is arbitrary, but must be a unique non-zero value for a given interface and direction. Setting this object to an existing sequence number value for a given interface and direction causes the ACL corresponding to that value to be replaced with this ACL.
INT msanSecurityAclProfileAclType	1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.3	INTEGER	not-accessible	The type of this ACL, which is used to interpret the aclIfId object value.
U32 msanSecurityAclProfileAclId	1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.4	Unsigned32	not-accessible	The ACL identifier value. For the IP ACLs, the actual ACL number is its identifier as follows: IP standard ranges from 1-99, IP extended ranges from 100-199, and IP advanced ranges 200-299.
ROW msanSecurityAclProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.6.3.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanL2cpProfile	1.3.6.1.4.1.1332.1.1.5.3.3.7
msanL2cpProfileTable	1.3.6.1.4.1.1332.1.1.5.3.3.7.1		not-accessible	L2CP (Layer 2 Control Protocol) Profile table
msanL2cpProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1		not-accessible	L2cp Profile table entry.
OCT msanL2cpProfileName	1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.1	OCTET STRING	not-accessible	Name of the L2CP profile.
INT msanL2cpProfileProtection	1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanL2cpProfileStatus = dynamic(2)
INT msanL2cpProfileStatus	1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.3	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
OCT msanL2cpProfileDescription	1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.4	OCTET STRING	read-write	Attribute specifies text which describes the associated object.
ROW msanL2cpProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.7.1.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanL2cpProtocolTable	1.3.6.1.4.1.1332.1.1.5.3.3.7.2		not-accessible	Table with list of L2CP protocols
msanL2cpProtocolEntry	1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1		not-accessible	Description.
OCT msanL2cpProtocolName	1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.1	OCTET STRING	not-accessible	L2CP protocol name
MAC msanL2cpProtocolMacDestAddr	1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.2	MacAddress	read-write	MAC destination address of L2CP protocol. Empty string indicates that protocol is related to any MAC address.
I32 msanL2cpProtocolEthertype	1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.3	Integer32	read-write	L2CP protocol Ethertype. A value of -1 indicates that parameter has not been defined.
I32 msanL2cpProtocolSubtype	1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.4	Integer32	read-write	L2CP protocol subtype. A value of -1 indicates that parameter has not been defined.
ROW msanL2cpProtocolRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.7.2.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported.
msanL2cpProfileProtocolTable	1.3.6.1.4.1.1332.1.1.5.3.3.7.3		not-accessible	Table with connection between profiles and protocols
msanL2cpProfileProtocolEntry	1.3.6.1.4.1.1332.1.1.5.3.3.7.3.1		not-accessible	Description.
INT msanL2cpProfileProtocolRule	1.3.6.1.4.1.1332.1.1.5.3.3.7.3.1.1	INTEGER	read-write	L2CP protocol rule.
ROW msanL2cpProfileProtocolRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.7.3.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported. Row can be activated only when msanL2cpProfileProtocolRule is set.
msanL2cpProfileVlanTable	1.3.6.1.4.1.1332.1.1.5.3.3.7.4		not-accessible	Table is used for connecting l2cp profile with vlan_id.
msanL2cpProfileVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.3.7.4.1		not-accessible	Description.
ROW msanL2cpProfileVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.3.7.4.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanXdslProfile	1.3.6.1.4.1.1332.1.1.5.3.3.8
msanXdsl2LineConfTemplateTable	1.3.6.1.4.1.1332.1.1.5.3.3.8.1		not-accessible	Description.
msanXdsl2LineConfTemplateEntry	1.3.6.1.4.1.1332.1.1.5.3.3.8.1.1		not-accessible	Description.
INT msanXdsl2LineConfTempProtection	1.3.6.1.4.1.1332.1.1.5.3.3.8.1.1.1	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)
INT msanXdsl2LineConfTempStatus	1.3.6.1.4.1.1332.1.1.5.3.3.8.1.1.2	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
msanXdsl2LineAlarmConfTemplateTable	1.3.6.1.4.1.1332.1.1.5.3.3.8.2		not-accessible	Description.
msanXdsl2LineAlarmConfTemplateEntry	1.3.6.1.4.1.1332.1.1.5.3.3.8.2.1		not-accessible	Description.
INT msanXdsl2LineAlarmConfTempProtection	1.3.6.1.4.1.1332.1.1.5.3.3.8.2.1.1	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)
INT msanXdsl2LineAlarmConfTempStatus	1.3.6.1.4.1.1332.1.1.5.3.3.8.2.1.2	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
INT msanProfileConfigStatus	1.3.6.1.4.1.1332.1.1.5.3.3.100	INTEGER	read-write	Profile configuration status.
msanDhcpRelay	1.3.6.1.4.1.1332.1.1.5.3.4
msanDhcpRaGlobal	1.3.6.1.4.1.1332.1.1.5.3.4.1
INT msanDhcpRaStatus	1.3.6.1.4.1.1332.1.1.5.3.4.1.1	INTEGER	read-write	DHCP Relay Agent status.
INT msanDhcpRaMode	1.3.6.1.4.1.1332.1.1.5.3.4.1.2	INTEGER	read-write	Specifies if the DHCP Relay Agent mode is to be Simple or Full. Default value is Full.
INT msanDhcpRaCircuitType	1.3.6.1.4.1.1332.1.1.5.3.4.1.3	INTEGER	read-write	Specifies DHCP RA Circuit type as trusted(1) or untrusted(2).
INT msanDhcpRaOpt82	1.3.6.1.4.1.1332.1.1.5.3.4.1.4	INTEGER	read-write	Specifies DHCP Relay Agent general option 82 insertion status .
INT msanDhcpRaOpt82ReplyMode	1.3.6.1.4.1.1332.1.1.5.3.4.1.5	INTEGER	read-write	Specifies DHCP Relay Agent keep/remove option 82 in replies.
INT msanDhcpRaOpt82CircuitIdStatus	1.3.6.1.4.1.1332.1.1.5.3.4.1.6	INTEGER	read-write	Specifies the disable/enable inserting Circuit ID suboption. Default value is Enable.
INT msanDhcpRaOpt82RemoteIdStatus	1.3.6.1.4.1.1332.1.1.5.3.4.1.7	INTEGER	read-write	Specifies the disable/enable inserting Remote ID suboption. Default value is Enable.
INT msanDhcpRaOpt82UnicastExtStatus	1.3.6.1.4.1.1332.1.1.5.3.4.1.8	INTEGER	read-write	The desired state of insertion of option 82 in unicast frames.
IP msanDhcpRaFullModeSrvIpAddr	1.3.6.1.4.1.1332.1.1.5.3.4.1.9	IpAddress	read-write	The IP address of default DHCP Server for VLANs where DHCP RA is enabled in full mode (parameter msanDhcpRaVlanMode).
msanDhcpRaPortConfigTable	1.3.6.1.4.1.1332.1.1.5.3.4.2		not-accessible	Table od DHCP RA parameters per port.
msanDhcpRaPortConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.4.2.1		not-accessible	Description.
INT msanDhcpRaPortState	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.1	INTEGER	read-write	State of DHCP Relay Agent on the port (enable, disable, enable-client, enable-server)
OCT msanDhcpRaPortCircuitId	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.2	OCTET STRING	read-only	Option 82 Circuit Id for the port.
OCT msanDhcpRaPortRemoteId	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.3	OCTET STRING	read-write	Option 82 Remote Id for the port.
INT msanDhcpRaPortMeter	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.4	INTEGER	read-write	Enable or disable DHCP metering on port.
I32 msanDhcpRaPortMaxDataRate	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.5	Integer32	read-write	Allowed throughput of incoming DHCP traffic on a port (kb/s)
INT msanDhcpRaPortCircuitType	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.6	INTEGER	read-write	Specifies DHCP RA Circuit type per port as trusted(1) or untrusted(2).
INT msanDhcpRaPortOpt82	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.7	INTEGER	read-write	Specifies DHCP Relay Agent option 82 insertion status per port.
INT msanDhcpRaPortOpt82ReplyMode	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.8	INTEGER	read-write	Specifies DHCP Relay Agent keep/remove option 82 in replies per port.
INT msanDhcpRaPortOpt82UnicastExtStatus	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.9	INTEGER	read-write	The desired state of insertion of option 82 in unicast frames per port.
INT msanDhcpRaPortCircuitIdType	1.3.6.1.4.1.1332.1.1.5.3.4.2.1.10	INTEGER	read-write	Circuit Id syntax mode per port.
msanDhcpRaFullModeVlanTable	1.3.6.1.4.1.1332.1.1.5.3.4.3		not-accessible	Description.
msanDhcpRaFullModeVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.4.3.1		not-accessible	Description.
I32 msanDhcpRaFullModeVlanId	1.3.6.1.4.1.1332.1.1.5.3.4.3.1.1	Integer32	not-accessible	The VLAN identifier (refers to dot1qVlanIndex) where DHCP Client resides.
IP msanDhcpRaFullModeVlanSrvIpAddr	1.3.6.1.4.1.1332.1.1.5.3.4.3.1.2	IpAddress	not-accessible	The IP address of DHCP Server for specified VLAN.
ROW msanDhcpRaFullModeVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.4.3.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanDhcpRaStatTable	1.3.6.1.4.1.1332.1.1.5.3.4.5		not-accessible	Description.
msanDhcpRaStatEntry	1.3.6.1.4.1.1332.1.1.5.3.4.5.1		not-accessible	Description.
C32 msanDhcpRaStatDiscover	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.1	Counter32	read-only	Number of received DHCP DISCOVER packets.
C32 msanDhcpRaStatRequest	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.2	Counter32	read-only	Number of received DHCP REQUEST packets.
C32 msanDhcpRaStatOffer	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.3	Counter32	read-only	Number of received DHCP OFFER packets.
C32 msanDhcpRaStatACK	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.4	Counter32	read-only	Number of received DHCP ACKNOWLAGE (ACK) packets.
C32 msanDhcpRaStatNAK	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.5	Counter32	read-only	Number of received DHCP NOT ACKNOWLAGE (NAK) packets.
C32 msanDhcpRaStatDecline	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.6	Counter32	read-only	Number of received DHCP DECLINE packets.
C32 msanDhcpRaStatMaxPacketSizeExceeded	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.7	Counter32	read-only	Number of received DHCP packets with max. packet size exceeded.
C32 msanDhcpRaStatFrameErr	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.8	Counter32	read-only	Number of received DHCP packets with errors in frames.
C32 msanDhcpRaStatOpt82Present	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.9	Counter32	read-only	Number of received DHCP packets with Option 82 or giaddr present.
C32 msanDhcpRaStatFrameUnsync	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.10	Counter32	read-only	Number of received packets with frames not synchronized with state machines.
C32 msanDhcpRaStatRelease	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.11	Counter32	read-only	Number of received DHCP RELEASE packets.
C32 msanDhcpRaStatInform	1.3.6.1.4.1.1332.1.1.5.3.4.5.1.12	Counter32	read-only	Number of received DHCP INFORM packets.
msanDhcpRaVlanConfigTable	1.3.6.1.4.1.1332.1.1.5.3.4.6		not-accessible	Table od DHCP RA parameters per Vlan.
msanDhcpRaVlanConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.4.6.1		not-accessible	Description.
INT msanDhcpRaVlanState	1.3.6.1.4.1.1332.1.1.5.3.4.6.1.1	INTEGER	read-write	DHCP RA state for specified VLAN ID. Value notConfigured(2) means, that global setting is used(msanDhcpRaStatus).
INT msanDhcpRaVlanMode	1.3.6.1.4.1.1332.1.1.5.3.4.6.1.2	INTEGER	read-write	DHCP RA mode for specified VLAN ID. Value notConfigured(1) means, that global setting is used(msanDhcpRaMode).
INT msanDhcpRaVlanOpt82	1.3.6.1.4.1.1332.1.1.5.3.4.6.1.3	INTEGER	read-write	Specifies DHCP Relay Agent option 82 insertion status per vlan.
INT msanDhcpRaVlanOpt82ReplyMode	1.3.6.1.4.1.1332.1.1.5.3.4.6.1.4	INTEGER	read-write	Specifies DHCP Relay Agent keep/remove option 82 in replies per vlan.
INT msanDhcpRaVlanOpt82UnicastExtStatus	1.3.6.1.4.1.1332.1.1.5.3.4.6.1.5	INTEGER	read-write	The desired state of insertion of option 82 in unicast frames per vlan.
INT msanDhcpRaVlanCircuitIdType	1.3.6.1.4.1.1332.1.1.5.3.4.6.1.6	INTEGER	read-write	Circuit Id syntax mode per vlan.
msanDhcpRaPortVlanConfigTable	1.3.6.1.4.1.1332.1.1.5.3.4.7		not-accessible	Description.
msanDhcpRaPortVlanConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.4.7.1		not-accessible	Description.
OCT msanDhcpRaPortVlanRemoteId	1.3.6.1.4.1.1332.1.1.5.3.4.7.1.1	OCTET STRING	read-write	The VLAN identifier (refers to dot1qVlanIndex) where DHCP Client resides.
ROW msanDhcpRaPortVlanConfigRowStatus	1.3.6.1.4.1.1332.1.1.5.3.4.7.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanDhcpv6RaGlobal	1.3.6.1.4.1.1332.1.1.5.3.4.100
INT msanDhcpv6RaState	1.3.6.1.4.1.1332.1.1.5.3.4.100.1	INTEGER	read-write	DHCPv6 Relay Agent status.
INT msanDhcpv6RaMode	1.3.6.1.4.1.1332.1.1.5.3.4.100.2	INTEGER	read-write	DHCPv6 Relay Agent mode. ldra = Lightweight DHCPRv6
INT msanDhcpv6RaInterfaceIdStandard	1.3.6.1.4.1.1332.1.1.5.3.4.100.3	INTEGER	read-write	DHCPv6 RA Standard Interface Id type.
msanDhcpv6Statistics	1.3.6.1.4.1.1332.1.1.5.3.4.101
msanDhcpv6RaPortStatTable	1.3.6.1.4.1.1332.1.1.5.3.4.101.1		not-accessible	Description.
msanDhcpv6RaPortStatEntry	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1		not-accessible	Description.
I32 msanDhcpv6PortRaStatSolicit	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.1	Integer32	read-only	Number of received DHCPv6 solicit packets.
I32 msanDhcpv6PortRaStatAdvertise	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.2	Integer32	read-only	Number of received DHCPv6 advertise packets.
I32 msanDhcpv6PortRaStatRequest	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.3	Integer32	read-only	Number of received DHCPv6 request packets.
I32 msanDhcpv6PortRaStatReply	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.4	Integer32	read-only	Number of received DHCPv6 reply packets.
I32 msanDhcpv6PortRaStatRenew	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.5	Integer32	read-only	Number of received DHCPv6 renew packets.
I32 msanDhcpv6PortRaStatRebind	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.6	Integer32	read-only	Number of received DHCPv6 rebind packets.
I32 msanDhcpv6PortRaStatDecline	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.7	Integer32	read-only	Number of received DHCPv6 decline packets.
I32 msanDhcpv6PortRaStatReconfigure	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.8	Integer32	read-only	Number of received DHCPv6 reconfigure packets.
I32 msanDhcpv6PortRaStatRelease	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.9	Integer32	read-only	Number of received DHCPv6 release packets.
I32 msanDhcpv6PortRaStatInformRequest	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.10	Integer32	read-only	Number of received DHCPv6 inform request packets.
I32 msanDhcpv6PortRaStatRelayForward	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.11	Integer32	read-only	Number of received DHCPv6 relay forward packets.
I32 msanDhcpv6PortRaStatRelayReply	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.12	Integer32	read-only	Number of received DHCPv6 relay reply packets.
I32 msanDhcpv6PortRaStatOversizeError	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.100	Integer32	read-only	Number of discarded packets because max packet size exceeded.
I32 msanDhcpv6PortRaStatFrameError	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.101	Integer32	read-only	Number of discarded packets because frame error.
I32 msanDhcpv6PortRaStatFrameUnsyncError	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.102	Integer32	read-only	Number of received packets with frames not synchronized with state machines.
I32 msanDhcpv6PortRaStatSysError	1.3.6.1.4.1.1332.1.1.5.3.4.101.1.1.103	Integer32	read-only	Number of discarded packets because system error.
C32 msanDhcpv6RaStatSolicit	1.3.6.1.4.1.1332.1.1.5.3.4.101.100	Counter32	read-only	Number of received DHCPv6 solicit packets.
C32 msanDhcpv6RaStatAdvertise	1.3.6.1.4.1.1332.1.1.5.3.4.101.101	Counter32	read-only	Number of received DHCPv6 advertise packets.
C32 msanDhcpv6RaStatRequest	1.3.6.1.4.1.1332.1.1.5.3.4.101.102	Counter32	read-only	Number of received DHCPv6 request packets.
C32 msanDhcpv6RaStatReply	1.3.6.1.4.1.1332.1.1.5.3.4.101.103	Counter32	read-only	Number of received DHCPv6 reply packets.
C32 msanDhcpv6RaStatRenew	1.3.6.1.4.1.1332.1.1.5.3.4.101.104	Counter32	read-only	Number of received DHCPv6 renew packets.
C32 msanDhcpv6RaStatRebind	1.3.6.1.4.1.1332.1.1.5.3.4.101.105	Counter32	read-only	Number of received DHCPv6 rebind packets.
C32 msanDhcpv6RaStatDecline	1.3.6.1.4.1.1332.1.1.5.3.4.101.106	Counter32	read-only	Number of received DHCPv6 decline packets.
C32 msanDhcpv6RaStatReconfigure	1.3.6.1.4.1.1332.1.1.5.3.4.101.107	Counter32	read-only	Number of received DHCPv6 reconfigure packets.
C32 msanDhcpv6RaStatRelease	1.3.6.1.4.1.1332.1.1.5.3.4.101.108	Counter32	read-only	Number of received DHCPv6 reconfigure packets.
C32 msanDhcpv6RaStatInformRequest	1.3.6.1.4.1.1332.1.1.5.3.4.101.109	Counter32	read-only	Number of received DHCPv6 inform request packets.
C32 msanDhcpv6RaStatRelayForward	1.3.6.1.4.1.1332.1.1.5.3.4.101.110	Counter32	read-only	Number of received DHCPv6 Relay Forward packets.
C32 msanDhcpv6RaStatRelayReply	1.3.6.1.4.1.1332.1.1.5.3.4.101.112	Counter32	read-only	Number of received DHCPv6 Relay Reply packets.
C32 msanDhcpv6RaStatOversizeError	1.3.6.1.4.1.1332.1.1.5.3.4.101.200	Counter32	read-only	Number of discarded packets because max packet size exceeded.
C32 msanDhcpv6RaStatFrameError	1.3.6.1.4.1.1332.1.1.5.3.4.101.201	Counter32	read-only	Number of discareded packets because errors in frame.
C32 msanDhcpv6RaStatFrameUnsyncError	1.3.6.1.4.1.1332.1.1.5.3.4.101.202	Counter32	read-only	Number of received packets with frames not synchronized with state machines.
C32 msanDhcpv6RaStatSysError	1.3.6.1.4.1.1332.1.1.5.3.4.101.203	Counter32	read-only	Number of discared packets because system error.
msanDhcpv6RaPortConfigTable	1.3.6.1.4.1.1332.1.1.5.3.4.102		not-accessible	Table od DHCP RA parameters per port.
msanDhcpv6RaPortConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.4.102.1		not-accessible	Description.
INT msanDhcpv6RaPortState	1.3.6.1.4.1.1332.1.1.5.3.4.102.1.1	INTEGER	read-write	State of DHCPv6 Relay Agent on the port (enable, disable, enable-client, enable-server)
INT msanDhcpv6RaPortTrusted	1.3.6.1.4.1.1332.1.1.5.3.4.102.1.2	INTEGER	read-write	Specifies DHCP RA Circuit type per port as trusted(1) or untrusted(2). Default value for user ports is untrusted(2) and for network ports trusted(1).
INT msanDhcpv6RaPortInterfaceIdStandard	1.3.6.1.4.1.1332.1.1.5.3.4.102.1.3	INTEGER	read-write	DHCPv6 RA Circuit Id syntax mode per port.
OCT msanDhcpv6RaPortInterfaceId	1.3.6.1.4.1.1332.1.1.5.3.4.102.1.4	OCTET STRING	read-only	DHCPv6 Option 82 Circuit Id for the port.
OCT msanDhcpv6RaPortRemoteId	1.3.6.1.4.1.1332.1.1.5.3.4.102.1.5	OCTET STRING	read-write	DHCPv6 Remote Id value for the port. If empty string, remote id is not added to DHCPv6 package.
INT msanDhcpv6RaPortRemoteIdEnterpriseNum	1.3.6.1.4.1.1332.1.1.5.3.4.102.1.6	INTEGER	read-write	DHCPv6 Remote Id enterprise number for the port.
msanDhcpv6RaVlanConfigTable	1.3.6.1.4.1.1332.1.1.5.3.4.103		not-accessible	Table od DHCP RA parameters per Vlan.
msanDhcpv6RaVlanConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.4.103.1		not-accessible	Description.
INT msanDhcpv6RaVlanState	1.3.6.1.4.1.1332.1.1.5.3.4.103.1.1	INTEGER	read-write	DHCP RA state for specified VLAN ID.
INT msanDhcpv6RaVlanInterfaceIdStandard	1.3.6.1.4.1.1332.1.1.5.3.4.103.1.2	INTEGER	read-write	DHCPv6 RA Circuit Id syntax mode per port.
msanDhcpv6RaPortVlanConfigTable	1.3.6.1.4.1.1332.1.1.5.3.4.104		not-accessible	Description.
msanDhcpv6RaPortVlanConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.4.104.1		not-accessible	Description.
OCT msanDhcpv6RaPortVlanRemoteId	1.3.6.1.4.1.1332.1.1.5.3.4.104.1.1	OCTET STRING	read-write	DHCPv6 Remote Id value for specified vlan_id per port.
INT msanDhcpv6RaPortVlanRemoteIdEnterpriseNum	1.3.6.1.4.1.1332.1.1.5.3.4.104.1.2	INTEGER	read-write	DHCPv6 Remote Id enterprise number for specified vlan_id per port.
ROW msanDhcpv6RaPortVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.4.104.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanSntp	1.3.6.1.4.1.1332.1.1.5.3.5
msanSntpGlobal	1.3.6.1.4.1.1332.1.1.5.3.5.1
OCT msanSntpTzOffset	1.3.6.1.4.1.1332.1.1.5.3.5.1.1	OCTET STRING	read-write	Specifies the time zone offset time in format hh:mm. Allowed range is -12 to 13.
OCT msanSntpTzName	1.3.6.1.4.1.1332.1.1.5.3.5.1.2	OCTET STRING	read-write	Time Zone name.
OCT msanSntpTzDstOffset	1.3.6.1.4.1.1332.1.1.5.3.5.1.3	OCTET STRING	read-write	Specifies the daylight saving time offset time in format hh:mm. Allowed range is -12 to 13.
I32 msanSntpTzDstStartMonth	1.3.6.1.4.1.1332.1.1.5.3.5.1.4	Integer32	read-write	Specifies the daylight saving time start month.
I32 msanSntpTzDstStartWeek	1.3.6.1.4.1.1332.1.1.5.3.5.1.5	Integer32	read-write	Specifies the daylight saving time start week.
INT msanSntpTzDstStartDayInWeek	1.3.6.1.4.1.1332.1.1.5.3.5.1.6	INTEGER	read-write	Specifies the daylight saving time start day in week.
OCT msanSntpTzDstStartTime	1.3.6.1.4.1.1332.1.1.5.3.5.1.7	OCTET STRING	read-write	Specifies the daylight saving time start time. Allowed range is 00:00 to 23:59.
I32 msanSntpTzDstEndMonth	1.3.6.1.4.1.1332.1.1.5.3.5.1.8	Integer32	read-write	Specifies the daylight saving time end month.
I32 msanSntpTzDstEndWeek	1.3.6.1.4.1.1332.1.1.5.3.5.1.9	Integer32	read-write	Specifies the daylight saving time end week.
INT msanSntpTzDstEndDayInWeek	1.3.6.1.4.1.1332.1.1.5.3.5.1.10	INTEGER	read-write	Specifies the daylight saving time end start day in week.
OCT msanSntpTzDstEndTime	1.3.6.1.4.1.1332.1.1.5.3.5.1.11	OCTET STRING	read-write	Specifies the daylight saving time end time. Allowed range is 00:00 to 23:59
msanSnmp	1.3.6.1.4.1.1332.1.1.5.3.7
msanSnmpGlobal	1.3.6.1.4.1.1332.1.1.5.3.7.1
U32 msanSnmpTrapRecvUdpPort	1.3.6.1.4.1.1332.1.1.5.3.7.1.1	Unsigned32	read-write	The UDP Port where SNMP traps are to be sent.
msanIgmpSnooping	1.3.6.1.4.1.1332.1.1.5.3.8
msanIgmpSnoopingGlobal	1.3.6.1.4.1.1332.1.1.5.3.8.1
INT msanIgmpSnoopingReportSuppression	1.3.6.1.4.1.1332.1.1.5.3.8.1.1	INTEGER	read-write	Report suppression mode for IGMP Snooping for the switch.
INT msanIgmpSnoopingAdminState	1.3.6.1.4.1.1332.1.1.5.3.8.1.2	INTEGER	read-write	IGMP snooping global state. Values enableAndUnknownGroupFlood(3) and enableAndMrouterFlood(4) are relevant only for MSAN Ethernet switch (ES) products, where enableAndUnknownGroupFlood(3) is supported only on IDC board.
I32 msanIgmpSnoopingLoggingVlanId	1.3.6.1.4.1.1332.1.1.5.3.8.1.3	Integer32	read-write	VLAN Id on which IGMP snooping logging is performed. Value 0 means that logging is disabled.
INT msanIgmpSnoopingViolationAction	1.3.6.1.4.1.1332.1.1.5.3.8.1.4	INTEGER	read-write	Removing one of the existing (the oldest) multicast group membership, or discarding a new group membership request.
INT msanIgmpSnoopingFastLeaveAdminMode	1.3.6.1.4.1.1332.1.1.5.3.8.1.5	INTEGER	read-write	This enables or disables IGMP Snooping Fast-Leave on user ports.
I32 msanIgmpSnoopingGroupMembershipInterval	1.3.6.1.4.1.1332.1.1.5.3.8.1.6	Integer32	read-write	The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than msanIgmpSnoopingMaxResponseTime
I32 msanIgmpSnoopingMaxResponseTime	1.3.6.1.4.1.1332.1.1.5.3.8.1.7	Integer32	read-write	The amount of time in seconds a switch will wait on a report after sending a query on the selected interface. This value must be less than msanIgmpSnoopingGroupMembershipInterval
INT msanIgmpVersion	1.3.6.1.4.1.1332.1.1.5.3.8.1.8	INTEGER	read-write	Version of processed IGMP frames.
INT msanIgmpClear	1.3.6.1.4.1.1332.1.1.5.3.8.1.9	INTEGER	read-write	Clear all IGMP snooping entries.
msanIgmpSnoopingTable	1.3.6.1.4.1.1332.1.1.5.3.8.2		not-accessible	Description.
msanIgmpSnoopingEntry	1.3.6.1.4.1.1332.1.1.5.3.8.2.1		not-accessible	Description.
I32 msanIgmpSnoopingIntfStandaloneQuerier	1.3.6.1.4.1.1332.1.1.5.3.8.2.1.1	Integer32	read-write	Specify the period of time in seconds you want the IGMP Standalone Querier generate IGMP query packets. Value must be higher than msanIgmpSnoopingMaxResponseTime and lower than msanIgmpSnoopingGroupMembershipInterval or 0. The default is 0. A value of zero indicates that standalone querier is disabled. IGMP SA Querier can be activated only on one interface at the same time.
INT msanIgmpSnoopingIntfFilter	1.3.6.1.4.1.1332.1.1.5.3.8.2.1.2	INTEGER	read-write	Filtering of IGMP join/leave reports or queries frames.
INT msanIgmpSnoopingGroupLimit	1.3.6.1.4.1.1332.1.1.5.3.8.2.1.3	INTEGER	read-write	A maximum numbers of IGMP groups per interface. Value 0 means no limits.
msanSwitchIGMPVlanCurrentMrouterTable	1.3.6.1.4.1.1332.1.1.5.3.8.3		not-accessible	Description.
msanSwitchIGMPVlanCurrentMrouterEntry	1.3.6.1.4.1.1332.1.1.5.3.8.3.1		not-accessible	Description.
I32 msanSwitchIGMPVlanCurrentMrouterEnableState	1.3.6.1.4.1.1332.1.1.5.3.8.3.1.1	Integer32	read-only	Returns per-interface per-vlan pairs where IGMP Mrouter is enabled.
msanSwitchIGMPSnoopingStaticIntfMulticastRouterTable	1.3.6.1.4.1.1332.1.1.5.3.8.4		not-accessible	Description.
msanSwitchIGMPSnoopingStaticIntfMulticastRouterEntry	1.3.6.1.4.1.1332.1.1.5.3.8.4.1		not-accessible	Description.
U32 msanSwitchIGMPSnoopingIntfIndex	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.1	Unsigned32	read-only	The port number to be selected. Each port maps to an interface.
INT msanSwitchIGMPSnoopingIntfAdminMode	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.2	INTEGER	read-write	This enables or disables IGMP Snooping on a selected interface.
I32 msanSwitchIGMPSnoopingIntfGroupMembershipInterval	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.3	Integer32	read-write	The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.
I32 msanSwitchIGMPSnoopingIntfMaxResponseTime	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.4	Integer32	read-write	The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.
I32 msanSwitchIGMPSnoopingIntfMRPExpirationTime	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.5	Integer32	read-write	The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached.
INT msanSwitchIGMPSnoopingIntfFastLeaveAdminMode	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.6	INTEGER	read-write	This enables or disables IGMP Snooping Fast-Leave on specified interface.
INT msanSwitchIGMPSnoopingStaticIntfMulticastRouterMode	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.7	INTEGER	read-write	Mode of static IGMP Mrouter on selected interface.
VLA msanSwitchIGMPSnoopingIntfVlanIDs	1.3.6.1.4.1.1332.1.1.5.3.8.4.1.8	VlanList	read-only	This field lists all the VlanIDs which include the selected interface.
msanSwitchIGMPVlanStaticMrouterTable	1.3.6.1.4.1.1332.1.1.5.3.8.5		not-accessible	Description.
msanSwitchIGMPVlanStaticMrouterEntry	1.3.6.1.4.1.1332.1.1.5.3.8.5.1		not-accessible	Description.
ROW msanSwitchIGMPVlanStaticMrouterEnableState	1.3.6.1.4.1.1332.1.1.5.3.8.5.1.1	RowStatus	read-create	Object used to create a new row or modify or destroy an existing row in manner described in the definition of the RowStatus textual. Supported states are Active(1), CreateAndGo(4) and Destroy(6). Row is created with CreateAndGo(4). This enables IGMP Mrouter on a per-interface per-vlan basis and the row goes to Active(1). The row is removed with Destroy(6) and IGMP Mrouter on this interface/VLAN pair is disabled. Values NotInService(2), NotReady(3) and CreateAndWait(5) are not supported.
msanSwitchIGMPSnoopingVlanTable	1.3.6.1.4.1.1332.1.1.5.3.8.6		not-accessible	A table of the IGMP Snooping Vlan configuration entries.
msanSwitchIGMPSnoopingVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.8.6.1		not-accessible	Represents entry for a IGMP Snooping Vlan.
INT msanSwitchIGMPSnoopingVlanAdminMode	1.3.6.1.4.1.1332.1.1.5.3.8.6.1.1	INTEGER	read-write	This enables or disables IGMP Snooping on a selected Vlan interface.
I32 msanSwitchIGMPSnoopingVlanGroupMembershipInterval	1.3.6.1.4.1.1332.1.1.5.3.8.6.1.2	Integer32	read-write	The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.
I32 msanSwitchIGMPSnoopingVlanMaxResponseTime	1.3.6.1.4.1.1332.1.1.5.3.8.6.1.3	Integer32	read-write	The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.
INT msanSwitchIGMPSnoopingVlanFastLeaveAdminMode	1.3.6.1.4.1.1332.1.1.5.3.8.6.1.4	INTEGER	read-write	This enables or disables IGMP Snooping on the selected vlan.
I32 msanSwitchIGMPSnoopingVlanMRPExpirationTime	1.3.6.1.4.1.1332.1.1.5.3.8.6.1.5	Integer32	read-write	The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers attached. This parameter is configurable only for exisiting Vlans.
INT msanSwitchIGMPSnoopingVlanAdminState	1.3.6.1.4.1.1332.1.1.5.3.8.6.1.6	INTEGER	read-write	IGMP Snooping state on a selected Vlan interface. This parameter is ignored if global msanIgmpSnoopingAdminState value is disableAndDiscard(0) or disableAndBroadcast(1).
msanSwitchIGMPProxyVlanTable	1.3.6.1.4.1.1332.1.1.5.3.8.7		not-accessible	A table of the IGMP Proxy Vlan configuration entries.
msanSwitchIGMPProxyVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.8.7.1		not-accessible
IP msanSwitchIGMPProxyVlanIpAddr	1.3.6.1.4.1.1332.1.1.5.3.8.7.1.1	IpAddress	not-accessible	IGMP Proxy IP address. If set to 0.0.0.0, default IP address is used (IP address of MN interface -> msanNetworkIPAddress).
ROW msanSwitchIGMPProxyVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.8.7.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanIgmpStatistics	1.3.6.1.4.1.1332.1.1.5.3.8.8
msanIgmpStatGlobal	1.3.6.1.4.1.1332.1.1.5.3.8.8.1
C32 msanIgmpStatRxV1	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.1	Counter32	read-only	Number of received IGMP v1 packets.
C32 msanIgmpStatRxV2Join	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.2	Counter32	read-only	Number of received IGMP v2 join packets.
C32 msanIgmpStatRxV2Leave	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.3	Counter32	read-only	Number of received IGMP v2 leave packets.
C32 msanIgmpStatRxV3Report	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.4	Counter32	read-only	Number of received IGMP v3 report packets.
C32 msanIgmpStatRxQuery	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.5	Counter32	read-only	Number of received IGMP query packets.
C32 msanIgmpStatRxError	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.6	Counter32	read-only	Number of received corrupted or unknown IGMP packets.
C32 msanIgmpStatRxBlockByIgmpFilter	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.7	Counter32	read-only	Number of received IGMP packets blocked by IGMP filter.
C32 msanIgmpStatRxBlockByMcastAcl	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.8	Counter32	read-only	Number of received IGMP packets blocked by Multicast ACL.
C32 msanIgmpStatRxBlockByMcastCac	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.9	Counter32	read-only	Number of received IGMP packets blocked by Multicast CAC.
C32 msanIgmpStatRxBlockByIgmpVersion	1.3.6.1.4.1.1332.1.1.5.3.8.8.1.10	Counter32	read-only	Number of received IGMP packets blocked by IGMP Version Control.
msanIgmpPortStatTable	1.3.6.1.4.1.1332.1.1.5.3.8.8.2		not-accessible	Description.
msanIgmpPortStatEntry	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1		not-accessible	Description.
C32 msanIgmpPortStatRxV1	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.1	Counter32	read-only	Number of received IGMP v1 packets.
C32 msanIgmpPortStatTxV1	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.2	Counter32	read-only	Number of transmitted IGMP v1 packets.
C32 msanIgmpPortStatRxV2Join	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.3	Counter32	read-only	Number of received IGMP v2 join packets.
C32 msanIgmpPortStatTxV2Join	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.4	Counter32	read-only	Number of transmitted IGMP v2 join packets.
C32 msanIgmpPortStatRxV2Leave	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.5	Counter32	read-only	Number of received IGMP v2 leave packets.
C32 msanIgmpPortStatTxV2Leave	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.6	Counter32	read-only	Number of transmitted IGMP v2 leave packets.
C32 msanIgmpPortStatRxV3Report	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.7	Counter32	read-only	Number of received IGMP v3 report packets.
C32 msanIgmpPortStatTxV3Report	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.8	Counter32	read-only	Number of transmitted IGMP v3 report packets.
C32 msanIgmpPortStatRxQuery	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.9	Counter32	read-only	Number of received IGMP query packets.
C32 msanIgmpPortStatRxError	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.10	Counter32	read-only	Number of received corrupted or unknown IGMP packets.
C32 msanIgmpPortStatRxBlockByIgmpFilter	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.11	Counter32	read-only	Number of received IGMP packets blocked by IGMP filter.
C32 msanIgmpPortStatRxBlockByMcastAcl	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.12	Counter32	read-only	Number of received IGMP packets blocked by Multicast ACL.
C32 msanIgmpPortStatRxBlockByMcastCac	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.13	Counter32	read-only	Number of received IGMP packets blocked by Multicast CAC.
C32 msanIgmpPortStatTxQuery	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.14	Counter32	read-only	Number of transmitted IGMP query packets.
C32 msanIgmpPortStatRxBlockByIgmpVersion	1.3.6.1.4.1.1332.1.1.5.3.8.8.2.1.15	Counter32	read-only	Number of received IGMP packets blocked by IGMP Version.
msanPort	1.3.6.1.4.1.1332.1.1.5.3.10
msanPortGlobal	1.3.6.1.4.1.1332.1.1.5.3.10.1
msanPortTable	1.3.6.1.4.1.1332.1.1.5.3.10.2		not-accessible	Description.
msanPortEntry	1.3.6.1.4.1.1332.1.1.5.3.10.2.1		not-accessible	Description.
INT msanPortMNFlag	1.3.6.1.4.1.1332.1.1.5.3.10.2.1.1	INTEGER	read-write	This object determines whether to allow or not allow management access to a specific link. The factory default is enabled.
INT msanPortMasterSlave	1.3.6.1.4.1.1332.1.1.5.3.10.2.1.6	INTEGER	read-write	This object determines whether Gb port should be master or slave. Set to none when auto-negotiation and for non-Gb ports.
BIT msanPortNegCapAdvertisedBits	1.3.6.1.4.1.1332.1.1.5.3.10.2.1.7	Bits	read-write	A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for capabilities that are listed above. Only b1000baseXFD(13) and b1000baseTFD(15) are currently supported.
INT msanPortSpeedDuplex	1.3.6.1.4.1.1332.1.1.5.3.10.2.1.8	INTEGER	read-write	Speed and duplex mode of the interface.
INT msanPortStpP2PAutoState	1.3.6.1.4.1.1332.1.1.5.3.10.2.1.20	INTEGER	read-write	The field extends ISKRATEL-MSAN-BASICCONF-MIB.agentStpCstPortOperPointToPoint by the value.
INT msanPortUsageType	1.3.6.1.4.1.1332.1.1.5.3.10.2.1.21	INTEGER	read-write	This object specifies the type of an interface whether it is an uplink or downlink.
msanPppoeIA	1.3.6.1.4.1.1332.1.1.5.3.11
msanPppoeIAGlobal	1.3.6.1.4.1.1332.1.1.5.3.11.1
INT msanPppoeIAStatus	1.3.6.1.4.1.1332.1.1.5.3.11.1.1	INTEGER	read-write	Specifies if the PPPOE Intermadiate Agent Service is to be Enabled or Disabled.
INT msanPppoeIAVsaReplyMode	1.3.6.1.4.1.1332.1.1.5.3.11.1.2	INTEGER	read-write	Specifies PPPOE Intermadiate Agent keep/remove option 82 in replies.
INT msanPppoeIACircuitIdStatus	1.3.6.1.4.1.1332.1.1.5.3.11.1.3	INTEGER	read-write	Specifies the disable/enable inserting Circuit ID suboption.
INT msanPppoeIARemoteIdStatus	1.3.6.1.4.1.1332.1.1.5.3.11.1.4	INTEGER	read-write	Specifies the disable/enable inserting Remote ID suboption.
msanPppoeIAPortTable	1.3.6.1.4.1.1332.1.1.5.3.11.2		not-accessible	Description.
msanPppoeIAPortEntry	1.3.6.1.4.1.1332.1.1.5.3.11.2.1		not-accessible	Description.
INT msanPppoeIAPortStatus	1.3.6.1.4.1.1332.1.1.5.3.11.2.1.1	INTEGER	read-write	State of PPPoE Intermadiate Agent on the port
OCT msanPppoeIAPortRemoteId	1.3.6.1.4.1.1332.1.1.5.3.11.2.1.2	OCTET STRING	read-write	Remote Id for the port.
INT msanPppoeIAPortCircuitType	1.3.6.1.4.1.1332.1.1.5.3.11.2.1.3	INTEGER	read-write	PPPoE IA Circuit type per port.
msanPppoeIaStatistics	1.3.6.1.4.1.1332.1.1.5.3.11.3
C32 msanPppoeIaStatPADI	1.3.6.1.4.1.1332.1.1.5.3.11.3.1	Counter32	read-only	Number of PADI packets.
C32 msanPppoeIaStatPADR	1.3.6.1.4.1.1332.1.1.5.3.11.3.2	Counter32	read-only	Number of PADR packets.
C32 msanPppoeIaStatPADO	1.3.6.1.4.1.1332.1.1.5.3.11.3.3	Counter32	read-only	Number of PADO packets.
C32 msanPppoeIaStatPADS	1.3.6.1.4.1.1332.1.1.5.3.11.3.4	Counter32	read-only	Number of PADS packets.
C32 msanPppoeIaStatPADT	1.3.6.1.4.1.1332.1.1.5.3.11.3.5	Counter32	read-only	Number of PADT packets.
C32 msanPppoeIaStatUnsutableFrames	1.3.6.1.4.1.1332.1.1.5.3.11.3.6	Counter32	read-only	Number of packets with unsutable frame.
C32 msanPppoeIaStatUnknownFrames	1.3.6.1.4.1.1332.1.1.5.3.11.3.7	Counter32	read-only	Number of packets with unknown frame.
C32 msanPppoeIaStatInvalidFrames	1.3.6.1.4.1.1332.1.1.5.3.11.3.8	Counter32	read-only	Number of packets with invalid frame.
msanPppoeIaPortStatisticsTable	1.3.6.1.4.1.1332.1.1.5.3.11.3.9		not-accessible	Description.
msanPppoeIaPortStatisticsEntry	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1		not-accessible	Description.
C32 msanPppoeIaPortStatPADI	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.1	Counter32	read-only	Number of PADI packets on the port.
C32 msanPppoeIaPortStatPADR	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.2	Counter32	read-only	Number of PADR packets on the port.
C32 msanPppoeIaPortStatPADO	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.3	Counter32	read-only	Number of PADO packets on the port.
C32 msanPppoeIaPortStatPADS	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.4	Counter32	read-only	Number of PADS packets on the port.
C32 msanPppoeIaPortStatPADT	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.5	Counter32	read-only	Number of PADT packets on the port.
C32 msanPppoeIaPortStatUnsutableFrames	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.6	Counter32	read-only	Number of packets with unsutable frame on the port.
C32 msanPppoeIaPortStatUnknownFrames	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.7	Counter32	read-only	Number of packets with unknown frame on the port.
C32 msanPppoeIaPortStatInvalidFrames	1.3.6.1.4.1.1332.1.1.5.3.11.3.9.1.8	Counter32	read-only	Number of packets with invalid frame on the port.
msanPppoeIaVlanTable	1.3.6.1.4.1.1332.1.1.5.3.11.4		not-accessible	Description.
msanPppoeIaVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.11.4.1		not-accessible	Description.
INT msanPppoeIaVlanStatus	1.3.6.1.4.1.1332.1.1.5.3.11.4.1.1	INTEGER	read-write	State of PPPoE Intermadiate Agent per VLAN.
msanQoS	1.3.6.1.4.1.1332.1.1.5.3.12
msanQosGlobal	1.3.6.1.4.1.1332.1.1.5.3.12.1
msanIpAclRuleTable	1.3.6.1.4.1.1332.1.1.5.3.12.2		not-accessible	This table extends aclTable/aclRuleTable.
msanIpAclRuleEntry	1.3.6.1.4.1.1332.1.1.5.3.12.2.1		not-accessible	This table extends aclTable/aclRuleTable.
I32 msanIpAclIndex	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.1	Integer32	not-accessible	This is aclIndex in aclTable
I32 msanIpAclRuleIndex	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.2	Integer32	not-accessible	The index of the IP ACL rule (aclRuleIndex in aclRuleTable).
I32 msanIpAclRuleAssignVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.3	Integer32	read-write	Assign VLAN Id.
I32 msanIpAclRuleAssignCoSPriority	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.4	Integer32	read-write	Assign CoS priority
I32 msanIpAclRuleEgressIntf	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.5	Integer32	read-write	Egress interface ID (ifIndex/ifTable).
I32 msanIpAclRuleAssignVlanId2	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.6	Integer32	read-write	Assign Secondary VLAN ID -> add (if not exists) or change.
INT msanIpAclRuleRemoveVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.7	INTEGER	read-write	Remove VLAN Id (outer).
INT msanIpAclRuleIcmpType	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.8	INTEGER	read-write	ICMP message type used in the MAC ACL Classification. This parameter is used if aclRuleProtocol is set to icmp(1).
MAC msanIpAclRuleDestMacAddr	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.9	MacAddress	read-write	The Destination MAC address used in the Advanced IP ACL Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
MAC msanIpAclRuleDestMacMask	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.10	MacAddress	read-write	The Destination MAC address mask used in the Advanced IP Classification. This mask value identifies the portion of the msanIpAclRuleDestMacAddr that is compared against a packet. A non-contiguous mask value is permitted. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
MAC msanIpAclRuleSrcMacAddr	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.11	MacAddress	read-write	The Source MAC address used in the Advanced IP ACL Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
MAC msanIpAclRuleSrcMacMask	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.12	MacAddress	read-write	The Source MAC address mask used in the Advanced IP Classification. This mask value identifies the portion of the msanIpAclRuleSrcMacAddr that is compared against a packet. A non-contiguous mask value is permitted. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
INT msanIpAclRuleCos	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.13	INTEGER	read-write	The Class of Service (COS) used in the Advanced IP Classification. This is the three-bit user priority field in the 802.1Q tag header of a tagged Ethernet frame. For frames containing a double VLAN tag, this field is located in the first/outer tag. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
INT msanIpAclRuleCos2	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.14	INTEGER	read-write	The Secondary Class of Service (COS) used in the Advanced IP Classification. This is the three-bit user priority field in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.15	Unsigned32	read-write	The VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleVlanId2	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.16	Unsigned32	read-write	The Secondary VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
I32 msanIpAclRuleCVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.17	Integer32	read-write	The C-customer VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
I32 msanIpAclRuleSVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.18	Integer32	read-write	The S-service VLAN ID value used in the Advanced IP Classification. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
I32 msanIpAclRuleAssignCVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.19	Integer32	read-write	Assign C VLAN ID -> add (if not exists) or change. Used in the Advanced IP Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
I32 msanIpAclRuleAssignSVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.20	Integer32	read-write	Assign S VLAN ID -> add (if not exists) or change. Used in the Advanced IP Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
INT msanIpAclRuleRemoveSVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.21	INTEGER	read-write	Remove S-service VLAN ID. Used in the Advanced IP Classification. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleVlanIdRangeStart	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.22	Unsigned32	read-write	The VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleVlanIdRangeEnd	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.23	Unsigned32	read-write	The VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleVlanIdRangeStart changes the VLAN ID range start to the same value as the range end. The VLAN ID field is defined as the 12-bit VLAN identifier in the 802.1Q tag header of a tagged Ethernet frame. This is contained in the first/outer tag of a double VLAN tagged frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleVlanId2RangeStart	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.24	Unsigned32	read-write	The Secondary VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleVlanId2RangeEnd changes the VLAN ID range end to the same value as the range start. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleVlanId2RangeEnd	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.25	Unsigned32	read-write	The Secondary VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleVlanId2RangeStart changes the VLAN ID range start to the same value as the range end. The VLAN ID field is defined as the 12-bit VLAN identifier in the second 802.1Q tag header of a tagged Ethernet frame. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleSVlanIdRangeStart	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.26	Unsigned32	read-write	The S-service VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleSVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleSVlanIdRangeEnd	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.27	Unsigned32	read-write	The S-service VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleSVlanIdRangeStart changes the VLAN ID range start to the same value as the range end. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleCVlanIdRangeStart	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.28	Unsigned32	read-write	The C-customer VLAN ID range start value used in the Advanced IP Classification. Setting this value greater than the current msanIpAclRuleCVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
U32 msanIpAclRuleCVlanIdRangeEnd	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.29	Unsigned32	read-write	The C-customer VLAN ID range end value used in the Advanced IP Classification. Setting this value less than the current msanIpAclRuleCVlanIdRangeStart changes the VLAN ID range start to the same value as the range end. Advanced IP ACL: msanIpAclIndex value in range 200 ... 299
ADR msanIpAclRuleSrcIpv6Address	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.31	InetAddressIPv6	read-write	The Source IPv6 Address used in the ACL Classification.
I32 msanIpAclRuleSrcIpv6AddressMaskLen	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.32	Integer32	read-write	The length of the prefix (in bits) associated with the IPv6 source address of this entry (msanIpAclRuleSrcIpv6Address). Value 0 indicates that parameter has not been defined.
ADR msanIpAclRuleDestIpv6Address	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.33	InetAddressIPv6	read-write	The Destination IPv6 Address used in the ACL Classification.
I32 msanIpAclRuleDestIpv6AddressMaskLen	1.3.6.1.4.1.1332.1.1.5.3.12.2.1.34	Integer32	read-write	The length of the prefix (in bits) associated with the IPv6 destination address of this entry (msanIpAclRuleDestIpv6Address). Value 0 indicates that parameter has not been defined.
msanMacAclRuleTable	1.3.6.1.4.1.1332.1.1.5.3.12.3		not-accessible	This table extends aclMacTable/aclMacRuleTable.
msanMacAclRuleEntry	1.3.6.1.4.1.1332.1.1.5.3.12.3.1		not-accessible	This table extends aclMacTable/aclMacRuleTable.
I32 msanMacAclIndex	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.1	Integer32	not-accessible	This is aclMacIndex in aclMacTable
I32 msanMacAclRuleIndex	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.2	Integer32	not-accessible	The index of the MAC ACL rule (aclMACRuleIndex in aclMACRuleTable).
I32 msanMacAclRuleEgressIntf	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.3	Integer32	read-write	Egress Interface ID (ifIndex/ifTable).
I32 msanMacAclRuleAssignVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.4	Integer32	read-write	Assign VLAN Id.
I32 msanMacAclRuleAssignCoSPriority	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.5	Integer32	read-write	Assign CoS priority
I32 msanMacAclRuleAssignVlanId2	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.6	Integer32	read-write	Assign Secondary VLAN ID -> add (if not exists) or change.
INT msanMacAclRuleRemoveVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.7	INTEGER	read-write	Remove outer VLAN Id (outer).
I32 msanMacAclRuleCVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.8	Integer32	read-write	C-customer Vlan ID
I32 msanMacAclRuleSVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.9	Integer32	read-write	S-service Vlan ID
I32 msanMacAclRuleAssignCVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.10	Integer32	read-write	Assign C-customer VLAN ID -> add (if not exists) or change.
I32 msanMacAclRuleAssignSVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.11	Integer32	read-write	Assign S-service VLAN ID -> add (if not exists) or change.
INT msanMacAclRuleRemoveSVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.12	INTEGER	read-write	Remove S-service VLAN ID.
U32 msanMacAclRuleSVlanIdRangeStart	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.13	Unsigned32	read-write	The S-service VLAN ID range start value. Setting this value greater than the current msanMacAclRuleSVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start.
U32 msanMacAclRuleSVlanIdRangeEnd	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.14	Unsigned32	read-write	The S-service VLAN ID range end value. Setting this value less than the current msanMacAclRuleSVlanIdRangeStart changes the VLAN ID range start to the same value as the range end.
U32 msanMacAclRuleCVlanIdRangeStart	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.15	Unsigned32	read-write	The C-customer VLAN ID range start value. Setting this value greater than the current msanMacAclRuleCVlanIdRangeEnd changes the VLAN ID range end to the same value as the range start.
U32 msanMacAclRuleCVlanIdRangeEnd	1.3.6.1.4.1.1332.1.1.5.3.12.3.1.16	Unsigned32	read-write	The C-customer VLAN ID range end value. Setting this value less than the current msanMacAclRuleCVlanIdRangeStart changes the VLAN ID range start to the same value as the range end.
msanCosQueueControlTable	1.3.6.1.4.1.1332.1.1.5.3.12.4		not-accessible	Description.
msanCosQueueControlEntry	1.3.6.1.4.1.1332.1.1.5.3.12.4.1		not-accessible	Description.
I32 msanCosQueueControlIntfBurstSize	1.3.6.1.4.1.1332.1.1.5.3.12.4.1.1	Integer32	read-write	Specifies the maximum number of uncommitted bytes that the switch will try to send into the network. It is the number of bytes that are sent at a rate, higher than committed and that the next device in the network must be able to buffer without notifying a congestion. Default value is 0. Valid values are 16, 20, 28, 40, 76, 140, 268 and 524 kilobytes. Configuring shaping rate without burst size will take the maximum possible value of burst, which is 524 KB.
U32 msanCosQueueIntfShapingRate	1.3.6.1.4.1.1332.1.1.5.3.12.4.1.2	Unsigned32	read-write	Specifies the maximum bandwidth allowed, typically used to shape the outbound transmission rate. This value is controlled independently of any per-queue maximum bandwidth configuration. It is effectively a second-level shaping mechanism. Default value is 0. Valid Range is 0 to 10000000 kbps. The value 0 means maximum is unlimited.
msanCosQueueTable	1.3.6.1.4.1.1332.1.1.5.3.12.5		not-accessible	Table of class-of-service queue configuration parameters for the specified interface. This is extension of the table agentCosQueueTable.
msanCosQueueEntry	1.3.6.1.4.1.1332.1.1.5.3.12.5.1		not-accessible	Each entry describes a single class-of-service (COS) queue for a given Interface Index. The number of configurable COS queues for an interface vary based on device capabilities. All objects defined for this table entry contain a default value corresponding to a typical, non-preferential treatment of packets traversing the interface's COS queues.
I32 msanCosQueueIndex	1.3.6.1.4.1.1332.1.1.5.3.12.5.1.1	Integer32	not-accessible	The COS queue index, numbered 0 to (n-1), where n is the total number of configurable interface queues for the device as indicated by agentCosQueueNumQueuesPerPort. In general, a higher numbered queue index is used to support higher priority traffic, although actual operation may be altered via configuration through this table.
INT msanCosQueueWeight	1.3.6.1.4.1.1332.1.1.5.3.12.5.1.2	INTEGER	read-write	Weight of the queue being used in egress scheduling algorithm.
INT msanCosQueueLength	1.3.6.1.4.1.1332.1.1.5.3.12.5.1.3	INTEGER	read-write	Length of the queue in kB.
msanCosMapIntfTrustTable	1.3.6.1.4.1.1332.1.1.5.3.12.6		not-accessible	Description.
msanCosMapIntfTrustEntry	1.3.6.1.4.1.1332.1.1.5.3.12.6.1		not-accessible	Description.
INT msanCosMapIntfTrustMode	1.3.6.1.4.1.1332.1.1.5.3.12.6.1.1	INTEGER	read-write	This is copy of LVL7 parameter agentCosMapIntfTrustMode, except that index 0 is not supported. The class of service trust mode of an interface. When set to a trusted mode, the appropriate COS mapping table is used as follows: trustDot1p(2) : dot1dTrafficClassTable trustIpPrecedence(3): agentCosMapIpPrecTable trustIpDscp(4): agentCosMapIpDscpTable For an untrusted(1) interface, packets are handled in accordance with the dot1dPortDefaultUserPriority value of the ingress port.
msanQosProfileTable	1.3.6.1.4.1.1332.1.1.5.3.12.7		not-accessible	Description.
msanQosProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.12.7.1		not-accessible	Description.
OCT msanQosProfileName	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.1	OCTET STRING	not-accessible	QoS profile name.
INT msanQosProfileMatchInAny	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.2	INTEGER	read-write	Match every incoming packet frame.
MAC msanQosProfileMatchInMacDestAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.3	MacAddress	read-write	Match incoming packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined
MAC msanQosProfileMatchInMacDestMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.4	MacAddress	read-write	This mask value identifies the portion of msanQosProfileMatchInMacDestAddr that is compared with input packet. Empty string indicates that parameter has not been defined
MAC msanQosProfileMatchInMacSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.5	MacAddress	read-write	Match incoming packet frame with specified source MAC address. Empty string indicates that parameter has not been defined
MAC msanQosProfileMatchInMacSrcMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.6	MacAddress	read-write	This mask value identifies the portion of msanQosProfileMatchInMacSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined
I32 msanQosProfileMatchInCos	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.7	Integer32	read-write	Match incoming packet frame with specified CoS value (0-7). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchInCos2	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.8	Integer32	read-write	Match incoming packet frame with specified secondary (C-TAG) CoS value (0-7). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchInVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.9	Integer32	read-write	Match incoming packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchInVlanId2	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.10	Integer32	read-write	Match incoming packet frame with specified secondary (C-TAG) VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchInEthertype	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.11	Integer32	read-write	Match incoming packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileMatchInIpProtocol	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.12	Integer32	read-write	Match incoming packet frame with specified IP protocol value. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17
IP msanQosProfileMatchInIpSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.13	IpAddress	read-write	Match incoming packet frame with specified source IP address. Empty string indicates that parameter has not been defined.
IP msanQosProfileMatchInIpSrcMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.14	IpAddress	read-write	This mask value identifies the portion of msanQosProfileMatchInIpSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined
IP msanQosProfileMatchInIpDestAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.15	IpAddress	read-write	Match incoming packet frame with specified destination IP address. Empty string indicates that parameter has not been defined.
IP msanQosProfileMatchInIpDestMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.16	IpAddress	read-write	This mask value identifies the portion of msanQosProfileMatchInIpDestAddr that is compared with input packet. Empty string indicates that parameter has not been defined
I32 msanQosProfileMatchInIpDscp	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.17	Integer32	read-write	Match incoming packet frame with specified IP DSCP value. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileMatchInIpPrecedence	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.18	Integer32	read-write	Match incoming packet frame with specified IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined.
OCT msanQosProfileMatchInIpTosBits	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.19	OCTET STRING	read-write	Match incoming packet frame with specified IP TOS bits value. Empty string indicates that parameter has not been defined.
OCT msanQosProfileMatchInIpTosMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.20	OCTET STRING	read-write	This mask value identifies the portion of msanQosProfileMatchInIpTosBits that is compared against a packet. Empty string indicates that parameter has not been defined.
I32 msanQosProfileMatchInL4SrcPort	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.21	Integer32	read-write	Match incoming packet frame with specified source TCP/UDP port number. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileMatchInL4DestPort	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.22	Integer32	read-write	Match incoming packet frame with specified destination TCP/UDP port number in downstream direction. A value of -1 indicates that parameter has not been defined.
INT msanQosProfileMatchOutAny	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.23	INTEGER	read-write	Match every outgoing packet frame in upstream direction.
MAC msanQosProfileMatchOutMacDestAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.24	MacAddress	read-write	Match outgoing packet frame with specified destination MAC address. Empty string indicates that parameter has not been defined
MAC msanQosProfileMatchOutMacDestMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.25	MacAddress	read-write	This mask value identifies the portion of msanQosProfileMatchOutMacDestAddr that is compared with output packet. Empty string indicates that parameter has not been defined
MAC msanQosProfileMatchOutMacSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.26	MacAddress	read-write	Match outgoing packet frame with specified source MAC address. Empty string indicates that parameter has not been defined
MAC msanQosProfileMatchOutMacSrcMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.27	MacAddress	read-write	This mask value identifies the portion of msanQosProfileMatchOutMacSrcAddr that is compared with output packet. Empty string indicates that parameter has not been defined
I32 msanQosProfileMatchOutCos	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.28	Integer32	read-write	Match outgoing packet frame with specified CoS value (0-7). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchOutCos2	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.29	Integer32	read-write	Match outgoing packet frame with specified secondary (C-TAG) CoS value (0-7). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchOutVlanId	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.30	Integer32	read-write	Match outgoing packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchOutVlanId2	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.31	Integer32	read-write	Match outgoing packet frame with specified secondary (C-TAG) VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined
I32 msanQosProfileMatchOutEthertype	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.32	Integer32	read-write	Match outgoing packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileMatchOutIpProtocol	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.33	Integer32	read-write	Match outgoing packet frame with specified IP protocol value in upstream direction. A value of -1 indicates that parameter has not been defined. Some of standard protocol values: icmp - 1 igmp - 2 ip - 4 (ip in ip encapsulation) tcp - 6 udp - 17
IP msanQosProfileMatchOutIpSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.34	IpAddress	read-write	Match outgoing packet frame with specified source IP address. Empty string indicates that parameter has not been defined.
IP msanQosProfileMatchOutIpSrcMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.35	IpAddress	read-write	This mask value identifies the portion of msanQosProfileMatchOutIpSrcAddr that is compared with output packet. Empty string indicates that parameter has not been defined
IP msanQosProfileMatchOutIpDestAddr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.36	IpAddress	read-write	Match outgoing packet frame with specified destination IP address. Empty string indicates that parameter has not been defined.
IP msanQosProfileMatchOutIpDestMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.37	IpAddress	read-write	This mask value identifies the portion of msanQosProfileMatchOutIpDestAddr that is compared with output packet. Empty string indicates that parameter has not been defined
I32 msanQosProfileMatchOutIpDscp	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.38	Integer32	read-write	Match outgoing packet frame with specified IP DSCP value. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileMatchOutIpPrecedence	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.39	Integer32	read-write	Match outgoing packet frame with specified IP precedence (part of TOS field) value. A value of -1 indicates that parameter has not been defined.
OCT msanQosProfileMatchOutIpTosBits	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.40	OCTET STRING	read-write	Match outgoing packet frame with specified IP TOS bits value. Empty string indicates that parameter has not been defined.
OCT msanQosProfileMatchOutIpTosMask	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.41	OCTET STRING	read-write	This mask value identifies the portion of msanQosProfileMatchOutIpTosBits that is compared with output packet. Empty string indicates that parameter has not been defined
I32 msanQosProfileMatchOutL4SrcPort	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.42	Integer32	read-write	Match outgoing packet frame with specified source TCP/UDP port number in upstream direction. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileMatchOutL4DestPort	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.43	Integer32	read-write	Match outgoing packet frame with specified destination TCP/UDP port number. A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileInCdr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.44	Integer32	read-write	Incoming committed data rate (E-CDR) in kbps (0 1000000). A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileInPdr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.45	Integer32	read-write	Incoming peak data rate (E-PDR) in kbps (0 1000000). A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileOutCdr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.46	Integer32	read-write	Outgoing committed data rate (E-CDR) in kbps (0 1000000). A value of -1 indicates that parameter has not been defined.
I32 msanQosProfileOutPdr	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.47	Integer32	read-write	Outgoing peak data rate (E-PDR) in kbps (0 1000000). A value of -1 indicates that parameter has not been defined.
INT msanQosProfileInTrustMode	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.48	INTEGER	read-write	Trust mode for incoming packets which correspond to this profile. Default value is untrusted(1). Value untrustMarkCos(4) can be set if parameter msanQosProfileInMarkCos value is grater than -1. Value untrustMarkCos(5) can be set if parameter msanQosProfileInMarkDscp value is grater than -1.
INT msanQosProfileInMarkCos	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.49	INTEGER	read-write	Mark incoming packets with specified CoS value (0-7). A value of -1 indicates that parameter has not been defined
INT msanQosProfileInMarkDscp	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.50	INTEGER	read-write	Mark incoming packets with specified IP DSCP value. A value of -1 indicates that parameter has not been defined.
ROW msanQosProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.51	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). Value active(1) will activate and value destroy(6) will remove this entry. Other values are currently not supported.
INT msanQosProfilePriority	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.52	INTEGER	read-write	Priority of QoS profile. On interface can be linked only one QoS profile with high(2) prority (msanQoSIntProfileTable)
I32 msanQosProfileInCdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.53	Integer32	read-write	Incoming committed data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInCdr value.
I32 msanQosProfileInPdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.54	Integer32	read-write	Incoming peak data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileInPdr value.
I32 msanQosProfileOutCdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.55	Integer32	read-write	Outgoing committed data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value.
I32 msanQosProfileOutPdrBurstSize	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.56	Integer32	read-write	Outgoing peak data rate burst size in kB (0 16384). When parameter is set to 0 (default), it's automatically updated to default burst size in according with current msanQoSProfileOutCdr value.
ADR msanQosProfileMatchInSrcIpv6Address	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.58	InetAddressIPv6	read-write	Match incoming packet frame with specified source IPv6 address. Empty string indicates that parameter has not been defined.
I32 msanQosProfileMatchInSrcIpv6AddressMaskLen	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.59	Integer32	read-write	The length of the prefix (in bits) associated with the incoming IPv6 source address of this entry (msanQosProfileMatchInSrcIpv6Address). Value 0 indicates that parameter has not been defined.
ADR msanQosProfileMatchInDestIpv6Address	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.60	InetAddressIPv6	read-write	Match incoming packet frame with specified destination IPv6 address. Empty string indicates that parameter has not been defined.
I32 msanQosProfileMatchInDestIpv6AddressMaskLen	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.61	Integer32	read-write	The length of the prefix (in bits) associated with the incoming IPv6 destination address of this entry (msanQosProfileMatchInDestIpv6Address). Value 0 indicates that parameter has not been defined.
ADR msanQosProfileMatchOutSrcIpv6Address	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.63	InetAddressIPv6	read-write	Match outgoing packet frame with specified source IPv6 address. Empty string indicates that parameter has not been defined.
I32 msanQosProfileMatchOutSrcIpv6AddressMaskLen	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.64	Integer32	read-write	The length of the prefix (in bits) associated with the outcoming IPv6 source address of this entry (msanQosProfileMatchOutSrcIpv6Address). Value 0 indicates that parameter has not been defined.
ADR msanQosProfileMatchOutDestIpv6Address	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.65	InetAddressIPv6	read-write	Match outcoming packet frame with specified destination IPv6 address. Empty string indicates that parameter has not been defined.
I32 msanQosProfileMatchOutDestIpv6AddressMaskLen	1.3.6.1.4.1.1332.1.1.5.3.12.7.1.66	Integer32	read-write	The length of the prefix (in bits) associated with the outcoming IPv6 destination address of this entry (msanQosProfileMatchOutDestIpv6Address). Value 0 indicates that parameter has not been defined.
msanQosIntfProfileTable	1.3.6.1.4.1.1332.1.1.5.3.12.8		not-accessible	This table connects selected QoS profiles (msanQoSProfileName) to specified interfaces (ifIndex).
msanQosIntfProfileEntry	1.3.6.1.4.1.1332.1.1.5.3.12.8.1		not-accessible	Description.
I32 msanQosIntfProfileAtmVpi	1.3.6.1.4.1.1332.1.1.5.3.12.8.1.1	Integer32	read-write	ATM Virtual path identifier of the ADSL interface. Value -1 indicates that parameter has not been defined.
I32 msanQosIntfProfileAtmVci	1.3.6.1.4.1.1332.1.1.5.3.12.8.1.2	Integer32	read-write	ATM Virtual channel identifier of the ADSL interface. Value -1 indicates that parameter has not been defined.
ROW msanQosIntfProfileRowStatus	1.3.6.1.4.1.1332.1.1.5.3.12.8.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deactivation use notInService(2). For row deletion use destroy(6). Other values are currently not supported. On interface can be linked only one QoS profile with high(2) prority (msanQosProfilePriority)
msanQosStatistics	1.3.6.1.4.1.1332.1.1.5.3.12.9
msanQosPortStatTable	1.3.6.1.4.1.1332.1.1.5.3.12.9.1		not-accessible	Description.
msanQosPortStatEntry	1.3.6.1.4.1.1332.1.1.5.3.12.9.1.1		not-accessible	Description.
C32 msanQosPortStatInDroppedFrames	1.3.6.1.4.1.1332.1.1.5.3.12.9.1.1.1	Counter32	read-only	Number of dropped frames per port in incoming direction.
C32 msanQosPortStatOutDroppedFrames	1.3.6.1.4.1.1332.1.1.5.3.12.9.1.1.2	Counter32	read-only	Number of dropped frames per port in outgoing direction.
msanQosPortProfileStatTable	1.3.6.1.4.1.1332.1.1.5.3.12.9.2		not-accessible	Description.
msanQosPortProfileStatEntry	1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1		not-accessible	Description.
I32 msanQosPortProfileStatQueueCurrent	1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1.1	Integer32	read-only	Current queue occupation per profile per port (in number of packets) .
I32 msanQosPortProfileStatQueueAverage	1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1.2	Integer32	read-only	Average queue occupation per profile per port (in number of packets) .
I32 msanQosPortProfileStatQueueMax	1.3.6.1.4.1.1332.1.1.5.3.12.9.2.1.3	Integer32	read-only	Maximum queue occupation per profile per port (in number of packets) .
msanIpAclTable	1.3.6.1.4.1.1332.1.1.5.3.12.10		not-accessible	Description.
msanIpAclEntry	1.3.6.1.4.1.1332.1.1.5.3.12.10.1		not-accessible	Description.
I32 msanIpAclId	1.3.6.1.4.1.1332.1.1.5.3.12.10.1.1	Integer32	not-accessible	This is aclIndex in aclTable (1.3.6.1.4.1.1332.1.1.5.2.3.2.1)
INT msanIpAclProtection	1.3.6.1.4.1.1332.1.1.5.3.12.10.1.2	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)
INT msanIpAclStatus	1.3.6.1.4.1.1332.1.1.5.3.12.10.1.4	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
msanMacAclTable	1.3.6.1.4.1.1332.1.1.5.3.12.11		not-accessible	Description.
msanMacAclEntry	1.3.6.1.4.1.1332.1.1.5.3.12.11.1		not-accessible	Description.
I32 msanMacAclId	1.3.6.1.4.1.1332.1.1.5.3.12.11.1.1	Integer32	not-accessible	This is aclMacIndex in aclMacTable (1.3.6.1.4.1.1332.1.1.5.2.3.2.6)
INT msanMacAclProtection	1.3.6.1.4.1.1332.1.1.5.3.12.11.1.3	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanMacAclStatus = dynamic(2)
INT msanMacAclStatus	1.3.6.1.4.1.1332.1.1.5.3.12.11.1.4	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
msanForwardingDb	1.3.6.1.4.1.1332.1.1.5.3.13
msanForwardingDbGlobal	1.3.6.1.4.1.1332.1.1.5.3.13.3
INT msanAddressLearningMode	1.3.6.1.4.1.1332.1.1.5.3.13.3.1	INTEGER	read-write	Specifies how source MAC addresses are associated with the interfaces on the switch. If mode is specified as nomaconly, source MAC addresses are learned as pairs of incoming VLAN ID and the source MAC address. If mode is specified as maconly, all source MAC addresses are learned in a specified VLAN, VLAN ID of the VLAN the packet was received from is not remembered. This mode is used for General Purpose Service Based Tagging.
I32 msanAddressLearningVlanId	1.3.6.1.4.1.1332.1.1.5.3.13.3.2	Integer32	read-write	This is the VLAN ID which is used for learning source MAC addresses in maconly mode. All learned MAC addresses will be marked as received from this VLAN. VLAN with this VLAN ID is created on the switch and all physical intefaces are added to this VLAN. This VLAN ID cannot be used for configuring other VLANs on the switch.
INT msanSwitchAddressAgingTimeout	1.3.6.1.4.1.1332.1.1.5.3.13.3.3	INTEGER	read-write	The FDB entry's address aging timeout (in seconds).
msanDiagnostics	1.3.6.1.4.1.1332.1.1.5.3.14
msanDiagnosticsGlobal	1.3.6.1.4.1.1332.1.1.5.3.14.1
I32 msanDiagnosticsFanSpeedLevel	1.3.6.1.4.1.1332.1.1.5.3.14.1.1	Integer32	read-only	MSAN shelf fan current speed level. Higher level defines higer speed. Level 0 means fan is stopped. Maximum level is defined by parameter msanDiagnosticsMaxFanSpeedLevel
I32 msanDiagnosticsMaxFanSpeedLevel	1.3.6.1.4.1.1332.1.1.5.3.14.1.2	Integer32	read-only	MSAN shelf fan max speed level.
msanDiagnosticsTestTable	1.3.6.1.4.1.1332.1.1.5.3.14.2		not-accessible	Description.
msanDiagnosticsTestEntry	1.3.6.1.4.1.1332.1.1.5.3.14.2.1		not-accessible	Description.
I32 msanDiagnosticsTestCode	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.1	Integer32	not-accessible	Unique identification of a test program.
OCT msanDiagnosticsTestName	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.2	OCTET STRING	read-only	The name of a test program.
INT msanDiagnosticsTestActivity	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.3	INTEGER	read-write	Specifies the Test activity parameter for the diagnostic.
U32 msanDiagnosticsTestTime	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.4	Unsigned32	read-write	Test time, whose interpretation depends on test running mode: - for cyclical tests, it means the period at which the test is carried out one after another (time unit is milisecond) - for all others, it means time of day in the form 'hhmmss' (e.g. '224950') at which the test begins.
INT msanDiagnosticsTestPriority	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.6	INTEGER	read-write	Test priority parameter for the diagnostic.
INT msanDiagnosticsTestType	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.7	INTEGER	read-only	Type of starting the test. DECIMAL VALUE DESCRIPTION 1 At start-up & Recovery 2 Periodical 3 Daily
I32 msanDiagnosticsTestTimeMin	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.8	Integer32	read-only	Minimum possible value of parameter msanDiagnosticTestTime.
I32 msanDiagnosticsTestTimeMax	1.3.6.1.4.1.1332.1.1.5.3.14.2.1.9	Integer32	read-only	Maximum possible value of parameter msanDiagnosticTestTime.
msanDiagnosticsErrorTable	1.3.6.1.4.1.1332.1.1.5.3.14.3		not-accessible	Description.
msanDiagnosticsErrorEntry	1.3.6.1.4.1.1332.1.1.5.3.14.3.1		not-accessible	Description.
I32 msanDiagnosticsErrorCode	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.1	Integer32	not-accessible	Unique identification of an error reported during testing an object.
OCT msanDiagnosticsErrorDescription	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.2	OCTET STRING	read-only	Description of the error code.
INT msanDiagnosticsErrorPriority	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.3	INTEGER	read-write	Error priority.
OCT msanDiagnosticsErrorObjectType	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.4	OCTET STRING	read-only	Object type - List of values can be found in alr_def.h
OCT msanDiagnosticsErrorMeasure	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.5	OCTET STRING	read-only	Measure (what is done when an error occurs, for instance reset the node, ...) - List of values can be found in alr_def.h
INT msanDiagnosticsErrorMeasureActive	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.6	INTEGER	read-write	Activity of measure. With setting this parameter to notActive(0), you can prevent excecution of measure.
I32 msanDiagnosticsErrorProbableCause	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.7	Integer32	read-only	Probable cause.
I32 msanDiagnosticsErrorObjectTypeId	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.8	Integer32	read-only	Object type ID- List of values can be found in alr_def.h
I32 msanDiagnosticsErrorMeasureId	1.3.6.1.4.1.1332.1.1.5.3.14.3.1.9	Integer32	read-only	Measure (what is done when an error occurs, for instance reset the node, ...) - List of values can be found in alr_def.h
msanDiagnosticsTempTable	1.3.6.1.4.1.1332.1.1.5.3.14.4		not-accessible	Description.
msanDiagnosticsTempEntry	1.3.6.1.4.1.1332.1.1.5.3.14.4.1		not-accessible	Description.
I32 msanDiagnosticsTempSensorID	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.1	Integer32	not-accessible	Temperature sensor ID.
OCT msanDiagnosticsTempSensorName	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.2	OCTET STRING	read-only	Temperature sensor name.
I32 msanDiagnosticsTempCurrent	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.3	Integer32	read-only	Current temperature of the specified sensor in [deg C].
I32 msanDiagnosticsTempCriticUnderheatThreshold	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.4	Integer32	read-only	Sensor critical underheat threshold temperature limit in [deg C].
I32 msanDiagnosticsTempUnderheatThreshold	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.5	Integer32	read-only	Sensor underheat temperature threshold limit in [deg C].
I32 msanDiagnosticsTempOverheatThreshold	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.6	Integer32	read-only	Sensor overheat threshold temperature limit in [deg C].
I32 msanDiagnosticsTempCriticOverheatThreshold	1.3.6.1.4.1.1332.1.1.5.3.14.4.1.7	Integer32	read-only	Sensor critical overheat threshold temperature limit in [deg C].
msanDiagnosticsErrorFilterTable	1.3.6.1.4.1.1332.1.1.5.3.14.5		not-accessible	Description.
msanDiagnosticsErrorFilterEntry	1.3.6.1.4.1.1332.1.1.5.3.14.5.1		not-accessible	Description.
OCT msanDiagnosticsErrorFilterErrMask	1.3.6.1.4.1.1332.1.1.5.3.14.5.1.1	OCTET STRING	not-accessible	Error code in ascii format. Regular expression describing one or more error codes.
OCT msanDiagnosticsErrorFilterObjMask	1.3.6.1.4.1.1332.1.1.5.3.14.5.1.2	OCTET STRING	not-accessible	Type of object, which alarming is filtered for. Regular expression describing one or more test objects.
ROW msanDiagnosticsErrorFilterRowStatus	1.3.6.1.4.1.1332.1.1.5.3.14.5.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanDiagnosticsErrorSeverityTable	1.3.6.1.4.1.1332.1.1.5.3.14.6		not-accessible	Description.
msanDiagnosticsErrorSeverityEntry	1.3.6.1.4.1.1332.1.1.5.3.14.6.1		not-accessible	Description.
I32 msanDiagnosticsErrorSeverityErrCode	1.3.6.1.4.1.1332.1.1.5.3.14.6.1.1	Integer32	not-accessible	Unique identification of an error reported during testing an object. All error codes are stated in alr_def.h (KFMT)
INT msanDiagnosticsErrorSeverityErrPriority	1.3.6.1.4.1.1332.1.1.5.3.14.6.1.2	INTEGER	read-create	Priority of error.
OCT msanDiagnosticsErrorSeverityObjMask	1.3.6.1.4.1.1332.1.1.5.3.14.6.1.3	OCTET STRING	not-accessible	Type of object, which alarming is filtered for. Regular expression describing one or more test objects.
ROW msanDiagnosticsErrorSeverityRowStatus	1.3.6.1.4.1.1332.1.1.5.3.14.6.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanPpp	1.3.6.1.4.1.1332.1.1.5.3.15
msanPppGlobal	1.3.6.1.4.1.1332.1.1.5.3.15.1
IP msanPppLocalIpAddress	1.3.6.1.4.1.1332.1.1.5.3.15.1.1	IpAddress	read-write	Local IP address for PPP connection
IP msanPppRemoteIpAddress	1.3.6.1.4.1.1332.1.1.5.3.15.1.2	IpAddress	read-write	Remote IP address for PPP connection
INT msanPppAuthProtocol	1.3.6.1.4.1.1332.1.1.5.3.15.1.3	INTEGER	read-write	PPP authentication protocol. For MPS connection use CHAP.
I32 msanPppEchoInterval	1.3.6.1.4.1.1332.1.1.5.3.15.1.4	Integer32	read-write	LCP echo interval (in seconds) for session breakdown identification.
INT msanPppVanJacobsonCompression	1.3.6.1.4.1.1332.1.1.5.3.15.1.5	INTEGER	read-write	Control of VanJacobson compression. For MPS connection it must be disabled.
INT msanPppAdminState	1.3.6.1.4.1.1332.1.1.5.3.15.1.6	INTEGER	read-write	Global PPP connection administrative state.
msanAlarmPanel	1.3.6.1.4.1.1332.1.1.5.3.16
msanAlarmPanelGlobal	1.3.6.1.4.1.1332.1.1.5.3.16.1
INT msanAlarmPanelAudioAlarmPriority	1.3.6.1.4.1.1332.1.1.5.3.16.1.1	INTEGER	read-write	Alarm Panel Audio Alarm Priority.
INT msanAlarmPanelSerialPortType	1.3.6.1.4.1.1332.1.1.5.3.16.1.2	INTEGER	read-write	Type of equipment connected to serial port.
msanAlarmPanelTable	1.3.6.1.4.1.1332.1.1.5.3.16.2		not-accessible	Description.
msanAlarmPanelEntry	1.3.6.1.4.1.1332.1.1.5.3.16.2.1		not-accessible	Description.
I32 msanAlarmPanelIndex	1.3.6.1.4.1.1332.1.1.5.3.16.2.1.1	Integer32	not-accessible	Unique identification of an alarm panel.
INT msanAlarmPanelConnectionState	1.3.6.1.4.1.1332.1.1.5.3.16.2.1.2	INTEGER	read-only	Alarm panel connection status
INT msanAlarmPanelAdminState	1.3.6.1.4.1.1332.1.1.5.3.16.2.1.3	INTEGER	read-write	Flag determining whether an alarm panel is equipped or not.
msanAlarmPanelIndicatorTable	1.3.6.1.4.1.1332.1.1.5.3.16.3		not-accessible	Description.
msanAlarmPanelIndicatorEntry	1.3.6.1.4.1.1332.1.1.5.3.16.3.1		not-accessible	Description.
I32 msanAlarmPanelIndicatorIndex	1.3.6.1.4.1.1332.1.1.5.3.16.3.1.1	Integer32	not-accessible	Alarm panel indicator number.
I32 msanAlarmPanelIndicatorErrCode	1.3.6.1.4.1.1332.1.1.5.3.16.3.1.2	Integer32	read-write	Alarm panel indicator error number.
msanAlarmPanelInputTable	1.3.6.1.4.1.1332.1.1.5.3.16.4		not-accessible	Description.
msanAlarmPanelInputEntry	1.3.6.1.4.1.1332.1.1.5.3.16.4.1		not-accessible	Description.
I32 msanAlarmPanelInputIndex	1.3.6.1.4.1.1332.1.1.5.3.16.4.1.1	Integer32	not-accessible	Alarm panel input sensor number.
I32 msanAlarmPanelInputErrCode	1.3.6.1.4.1.1332.1.1.5.3.16.4.1.2	Integer32	read-write	Alarm panel input sensor error code.
INT msanAlarmPanelInputActiveLevel	1.3.6.1.4.1.1332.1.1.5.3.16.4.1.3	INTEGER	read-write	Alarm panel input sensor active level.
msanMvr	1.3.6.1.4.1.1332.1.1.5.3.17
msanMvrGlobal	1.3.6.1.4.1.1332.1.1.5.3.17.1
msanMvrPortTable	1.3.6.1.4.1.1332.1.1.5.3.17.2		not-accessible	Description.
msanMvrPortEntry	1.3.6.1.4.1.1332.1.1.5.3.17.2.1		not-accessible	Description.
INT msanMvrPortAdminMode	1.3.6.1.4.1.1332.1.1.5.3.17.2.1.1	INTEGER	read-write	Administrative mode for Multicast VLAN Registration (a.k.a. Service Based Tagging) for the selected interface
msanMvrMulticastGroupTable	1.3.6.1.4.1.1332.1.1.5.3.17.3		not-accessible	Description.
msanMvrMulticastGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.17.3.1		not-accessible	Description.
I32 msanMvrMulticastGroupMVlanId	1.3.6.1.4.1.1332.1.1.5.3.17.3.1.1	Integer32	not-accessible	VLAN ID (refers to dot1qVlanIndex) where MVR functionality is used.
IP msanMvrMulticastGroupStartIp	1.3.6.1.4.1.1332.1.1.5.3.17.3.1.2	IpAddress	not-accessible	Start IP Address of the multicast group range.
IP msanMvrMulticastGroupEndIp	1.3.6.1.4.1.1332.1.1.5.3.17.3.1.3	IpAddress	read-create	End IP Address of the multicast group range.
ROW msanMvrMulticastGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.17.3.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanMvrConfigTable	1.3.6.1.4.1.1332.1.1.5.3.17.4		not-accessible	Description.
msanMvrConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.17.4.1		not-accessible	Description.
I32 msanMvrConfigCVlanId	1.3.6.1.4.1.1332.1.1.5.3.17.4.1.1	Integer32	not-accessible	Customer VLAN ID for the selected interface from which IGMP Join/Leave messages will be remarked.
I32 msanMvrConfigMVlanId	1.3.6.1.4.1.1332.1.1.5.3.17.4.1.2	Integer32	not-accessible	Service provider multicast VLAN ID for the selected interface to which IGMP Join/Leave messages will be remarked.
I32 msanMvrConfigCos	1.3.6.1.4.1.1332.1.1.5.3.17.4.1.3	Integer32	read-write	Output CoS priority on the selected interface. IGMP messages received from this interface will have this priority when they are transmitted into service provider multicast VLAN. Value '-1' defines that original CoS value is not changed.
ROW msanMvrConfigRowStatus	1.3.6.1.4.1.1332.1.1.5.3.17.4.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMvrDvlanTable	1.3.6.1.4.1.1332.1.1.5.3.17.5		not-accessible	Description.
msanMvrDvlanEntry	1.3.6.1.4.1.1332.1.1.5.3.17.5.1		not-accessible	Description.
INT msanMvrDvlanRmOuterTagStatus	1.3.6.1.4.1.1332.1.1.5.3.17.5.1.1	INTEGER	read-write	The desired state of removing outer tags on IGMP packets funcionality.
INT msanMvrDvlanEthertypeRewriteStatus	1.3.6.1.4.1.1332.1.1.5.3.17.5.1.2	INTEGER	read-write	The desired state of rewriting ether type from outer vlan tag to inner vlan tag.
msanRemoteAccess	1.3.6.1.4.1.1332.1.1.5.3.18
msanRemoteAccessGlobal	1.3.6.1.4.1.1332.1.1.5.3.18.1
msanRemoteAccessFilterTable	1.3.6.1.4.1.1332.1.1.5.3.18.2		not-accessible	Description.
msanRemoteAccessFilterEntry	1.3.6.1.4.1.1332.1.1.5.3.18.2.1		not-accessible	Description.
INT msanRemoteAccessFilterRuleIndex	1.3.6.1.4.1.1332.1.1.5.3.18.2.1.1	INTEGER	not-accessible	Rule's index. Index should be continued, without gaps.
IP msanRemoteAccessFilterIp	1.3.6.1.4.1.1332.1.1.5.3.18.2.1.2	IpAddress	read-create	IP Address of the rule.
IP msanRemoteAccessFilterNetmask	1.3.6.1.4.1.1332.1.1.5.3.18.2.1.3	IpAddress	read-create	Netmask of the rule.
INT msanRemoteAccessFilterAction	1.3.6.1.4.1.1332.1.1.5.3.18.2.1.4	INTEGER	read-create	Action to be taken with a packet: accept or deny it.
ROW msanRemoteAccessFilterRowStatus	1.3.6.1.4.1.1332.1.1.5.3.18.2.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanDslSpecific	1.3.6.1.4.1.1332.1.1.5.3.19
msanDslSpecificGlobal	1.3.6.1.4.1.1332.1.1.5.3.19.1
INT msanDslSpecificSystemState	1.3.6.1.4.1.1332.1.1.5.3.19.1.1	INTEGER	read-only	VDSL system operational state. For normal blade operation this value should be operational (4). If value differ from 4, VDSL driver is not operational.
OCT msanDslSpecificSystemFirmware	1.3.6.1.4.1.1332.1.1.5.3.19.1.2	OCTET STRING	read-only	VDSL firmware version.
msanDslSpecificTable	1.3.6.1.4.1.1332.1.1.5.3.19.3		not-accessible	Description.
msanDslSpecificEntry	1.3.6.1.4.1.1332.1.1.5.3.19.3.1		not-accessible	Description.
OCT msanDslSpecificDsPsdMask	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.1	OCTET STRING	read-write	Unique name of the downstream PSD mask as defined by msanDslPsdMaskDsName.
OCT msanDslSpecificUsPsdMask	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.2	OCTET STRING	read-write	Unique name of the upstream PSD mask as defined by msanDslPsdMaskUsName.
INT msanDslSpecificLineState	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.3	INTEGER	read-only	VDSL system operational state. For normal blade operation this value should be active(3). If value is differ from 3, VDSL driver is not operational.
I32 msanDslSpecificMaxDelayDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.4	Integer32	read-write	Maximum interleave delay for the downstream interleaved channel. -1 means that value from profile will be used (xdsl2ChConfProfMaxDelayDs). This object is created based on xdsl2ChConfProfMaxDelayDs (VDSL2-LINE MIB)
I32 msanDslSpecificMaxDelayUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.5	Integer32	read-write	Maximum interleave delay for the upstream interleaved channel. -1 means that value from profile will be used (xdsl2ChConfProfMaxDelayUs). This object is created based on xdsl2ChConfProfMaxDelayUs (VDSL2-LINE MIB)
I32 msanDslSpecificMinProtectionDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.6	Integer32	read-write	Downstream impulse noise protection. -1 means that value from profile will be used (xdsl2ChConfProfMinProtectionDs) This object is created based on xdsl2ChConfProfMinProtectionDs(VDSL2-LINE MIB)
I32 msanDslSpecificMinProtectionUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.7	Integer32	read-write	Upstream impulse noise protection. -1 means that value from profile will be used (xdsl2ChConfProfMinProtectionUs) This object is created based on xdsl2ChConfProfMinProtectionUs(VDSL2-LINE MIB)
U32 msanDslSpecificMaxSnrmDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.8	Unsigned32	read-write	Downstream maximum Signal/Noise Margin. This object is created based on xdsl2LConfProfMaxSnrmDs (VDSL2-LINE MIB)
U32 msanDslSpecificMinSnrmDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.9	Unsigned32	read-write	Downstream minimum Signal/Noise Margin. This object is created based on xdsl2LConfProfMinSnrmDs (VDSL2-LINE MIB)
U32 msanDslSpecificMaxSnrmUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.10	Unsigned32	read-write	Upstream maximum Signal/Noise Margin. This object is created based on xdsl2LConfProfMaxSnrmUs (VDSL2-LINE MIB)
U32 msanDslSpecificMinSnrmUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.11	Unsigned32	read-write	Upstream minimum Signal/Noise Margin. This object is created based on xdsl2LConfProfMinSnrmUs (VDSL2-LINE MIB)
U32 msanDslSpecificRaUsNrmDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.12	Unsigned32	read-write	The Downstream Up-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaUsNrmDs (VDSL2-LINE MIB)
U32 msanDslSpecificRaUsNrmUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.13	Unsigned32	read-write	The Upstream Up-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaUsNrmUs (VDSL2-LINE MIB)
U32 msanDslSpecificRaUsTimeDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.14	Unsigned32	read-write	The Downstream Up-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaUsTimeDs (VDSL2-LINE MIB)
U32 msanDslSpecificRaUsTimeUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.15	Unsigned32	read-write	The Upstream Up-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaUsTimeUs (VDSL2-LINE MIB)
U32 msanDslSpecificRaDsNrmDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.16	Unsigned32	read-write	The Downstream Down-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaDsNrmDs (VDSL2-LINE MIB)
U32 msanDslSpecificRaDsNrmUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.17	Unsigned32	read-write	The Upstream Down-Shift Noise Margin (for dynamic rate adaptive mode). This object is created based on xdsl2LConfProfRaDsNrmUs (VDSL2-LINE MIB)
U32 msanDslSpecificRaDsTimeDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.18	Unsigned32	read-write	The Downstream Down-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaDsTimeDs (VDSL2-LINE MIB)
U32 msanDslSpecificRaDsTimeUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.19	Unsigned32	read-write	The Upstream Down-Shift Time Interval (for rate dynamic adaptive mode). This object is created based on xdsl2LConfProfRaDsTimeUs (VDSL2-LINE MIB)
U32 msanDslSpecificL0Time	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.20	Unsigned32	read-write	The minimum time between an exit from the L2 state and the next entry into the L2 state. This object is created based on xdsl2LConfProfL0Time (VDSL2-LINE MIB)
U32 msanDslSpecificL2Time	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.21	Unsigned32	read-write	The minimum time between an entry into the L2 state and the first power trim in the L2 state and between two consecutive power trims in the L2 State. This object is created based on xdsl2LConfProfL2Time (VDSL2-LINE MIB)
U32 msanDslSpecificL2Atpr	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.22	Unsigned32	read-write	The maximum aggregate transmit power reduction that can be performed at transition of L0 to L2 state or through a single power trim in the L2 state. This object is created based on xdsl2LConfProfL2Atpr (VDSL2-LINE MIB)
U32 msanDslSpecificL2Atprt	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.23	Unsigned32	read-write	The total maximum aggregate transmit power reduction that can be performed in an L2 state. This object is created based on xdsl2LConfProfL2Atprt (VDSL2-LINE MIB)
OCT msanDslSpecificScMaskDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.24	OCTET STRING	read-write	Downstream Sub-carriers mask. A bitmap of 4096 bits that allows masking up to 4096 downstream sub-carriers. If bit is set to '1', the respective downstream sub-carrier is masked (not used), and if set to '0', the respective sub-carrier is unmasked. This object is created based on xdsl2LConfProfScMaskDs (VDSL2-LINE MIB)
OCT msanDslSpecificScMaskUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.25	OCTET STRING	read-write	Upstream Sub-carriers mask. A bitmap of 4096 bits that allows masking up to 4096 downstream sub-carriers. If bit is set to '1', the respective downstream sub-carrier is masked (not used), and if set to '0', the respective sub-carrier is unmasked. This object is created based on xdsl2LConfProfScMaskUs (VDSL2-LINE MIB)
OCT msanDslSpecificRfiBands	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.26	OCTET STRING	read-write	For VDLS, this configuration parameter defines the bands where the PSD shall be reduced. Each band shall be represented by a start and stop subcarrier indices with a subcarrier spacing of 4.3125 kHz. Up to 16 bands may be specified. This parameter defines the RFI bands for both upstream and downstream directions. Each RFI band is represented by 4 octets: 16 bit start sub-carrier index followed by a 16 bit stop sub-carrier index. This object is created based on xdsl2LConfProfRfiBands (VDSL2-LINE MIB)
I32 msanDslSpecificMaxNomPsdDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.27	Integer32	read-write	The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. (0.1 dBm/Hz - physical values are -60 to -30 dBm/Hz). This object is created based on xdsl2LConfProfMaxNomPsdDs (VDSL2-LINE MIB)
I32 msanDslSpecificMaxNomPsdUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.28	Integer32	read-write	The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. (0.1 dBm/Hz - physical values are -60 to -30 dBm/Hz). This object is created based on xdsl2LConfProfMaxNomPsdUs (VDSL2-LINE MIB)
U32 msanDslSpecificMaxNomAtpDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.29	Unsigned32	read-write	The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. (0.1 dBm - physical values are 0 to 25.5 dBm). This object is created based on xdsl2LConfProfMaxNomAtpDs (VDSL2-LINE MIB)
U32 msanDslSpecificMaxNomAtpUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.30	Unsigned32	read-write	The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. (0.1 dBm - physical values are 0 to 25.5 dBm). This object is created based on xdsl2LConfProfMaxNomAtpUs (VDSL2-LINE MIB)
I32 msanDslSpecificMaxAggRxPwrUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.31	Integer32	read-write	The maximum upstream aggregate receive power over the relevant set of sub-carriers.. (0.1 dBm - physical values are -25.5 to 25.5 dBm). This object is created based on xdsl2LConfProfMaxAggRxPwrUs (VDSL2-LINE MIB)
INT msanDslSpecificClassMask	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.32	INTEGER	read-write	Predefined PSD mask. This object is created based on xdsl2LConfProfClassMask (VDSL2-LINE MIB)
U32 msanDslSpecificDpboEsEL	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.35	Unsigned32	read-write	Assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet). The electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency. 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. This object is created based on xdsl2LConfProfDpboEsEL (VDSL2-LINE MIB)
INT msanDslSpecificUpboKLF	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.36	INTEGER	read-write	Defines the upstream power backoff force mode. The three possible mode values are: auto(1), override(2), disableUpbo(3). This object is created based on xdsl2LConfProfUpboKLF (VDSL2-LINE MIB)
U32 msanDslSpecificUpboKL	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.37	Unsigned32	read-write	This configuration parameter defines the electrical length expressed in dB at 1MHz, configured by the CO-MIB. The value ranges from 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. This object is created based on xdsl2LConfProfUpboKL (VDSL2-LINE MIB)
INT msanDslSpecificSelt	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.39	INTEGER	read-write	Defines whether the line should be forced into the SELT (Single-Ended Loop Testing) diagnostics mode by the near-end xTU of this line. Upon completion of the loop diagnostic mode procedures, the Access Node shall set this object to 'inhibit'. The results of the SELT procedure are stored in the table msanDslSeltStatusTable. The status of the loop diagnostic procedure is indicated by msanDslSpecificSeltStatus.
INT msanDslSpecificSeltStatus	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.40	INTEGER	read-only	SELT (Single-Ended Loop Testing) status of dsl line.
INT msanDslSpecificPhyRDs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.41	INTEGER	read-write	Physical Layer Retransmission configuration in the downstream direction.
INT msanDslSpecificPhyRUs	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.42	INTEGER	read-write	Physical Layer Retransmission configuration in the upstream direction.
INT msanDslSpecificUpboUs1a	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.43	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band.
INT msanDslSpecificUpboUs1b	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.44	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz.
INT msanDslSpecificUpboUs2a	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.45	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band.
INT msanDslSpecificUpboUs2b	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.46	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz.
INT msanDslSpecificUpboUs3a	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.47	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band.
INT msanDslSpecificUpboUs3b	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.48	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz.
INT msanDslSpecificUpboUs4a	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.49	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'a' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. A UPBO PSD defined for each band shall consist of two parameters [a, b]. Parameter 'a' (xdsl2LConfProfUpboPsdA) ranges from 40 dBm/Hz (coded as 4000) to 80.95 dBm/Hz (coded as 8095) in steps of 0.01 dBm/Hz; and parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency 'f' expressed in MHz shall be equal to '-a-b(SQRT(f))'. Setting xdsl2LConfProfUpboPsdA to 4000 and xdsl2LConfProfUpboPsdB to 0 is a special configuration to disable UPBO in the respective upstream band.
INT msanDslSpecificUpboUs4b	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.50	INTEGER	read-write	ITU-T G.997.1, paragraph #7.3.1.2.14 (UPBOPSD-pb) Parameter defines the 'b' reference parameter of the UPBO reference PSD used to compute the upstream power back-off for the upstream band. Parameter 'b' (xdsl2LConfProfUpboPsdB) ranges from 0 dBm/Hz (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz.
OCT msanDslSpecificDpboEPsdMask	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.51	OCTET STRING	read-write	DPbo EPsd mask name. It should be of the downstream PSD mask as defined by msanDslPsdMaskDsName.
U32 msanDslSpecificDpboEsCmA	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.52	Unsigned32	read-create	ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMA) The E-side Cable Model parameter A (DPBOESCMA) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2-8 All values in the range are valid.
U32 msanDslSpecificDpboEsCmB	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.53	Unsigned32	read-create	ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMB) The E-side Cable Model parameter B (DPBOESCMB) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2-8 All values in the range are valid.
U32 msanDslSpecificDpboEsCmC	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.54	Unsigned32	read-create	ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOESCMC) The E-side Cable Model parameter C (DPBOESCMC) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back- off (DPBO) depending on this value. Possible values shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in steps of 2-8 All values in the range are valid.
U32 msanDslSpecificDpboMus	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.55	Unsigned32	read-create	ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOMUS) Assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange-based services. It shall be coded as an unsigned integer representing a PSD mask level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid.
U32 msanDslSpecificDpboFMin	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.56	Unsigned32	read-create	ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMIN) Minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz (coded as 0) to 8832 kHz (coded as 2048) in steps of 4.3125 kHz.
U32 msanDslSpecificDpboFMax	1.3.6.1.4.1.1332.1.1.5.3.19.3.1.57	Unsigned32	read-create	ITU-T G.997.1, paragraph #7.3.1.2.13 (DPBOFMAX) Maximum frequency at which DPBO may be applied. It ranges from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956) in steps of 4.3125 kHz.
msanDslPsdMaskDsTable	1.3.6.1.4.1.1332.1.1.5.3.19.4		not-accessible	Management of Downstream PSD Mask (G997.1 #7.3.1.2.9 )
msanDslPsdMaskDsEntry	1.3.6.1.4.1.1332.1.1.5.3.19.4.1		not-accessible	Description.
OCT msanDslPsdMaskDsName	1.3.6.1.4.1.1332.1.1.5.3.19.4.1.1	OCTET STRING	not-accessible	Downstream custom PSD mask name.
INT msanDslPsdMaskDsType	1.3.6.1.4.1.1332.1.1.5.3.19.4.1.2	INTEGER	read-only	Downstream custom PSD mask type. Possible values: default(1) - Default mask prepared by vendor, user is not allowed to delete or change it configured(2) - Mask created by user
XDS msanDslPsdMaskDsShape	1.3.6.1.4.1.1332.1.1.5.3.19.4.1.3	Xdsl2PsdMaskDs	read-write	The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of the first subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a second breakpoint. Octets 6-8 - Same, for a third breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCds-1. Each PSD reduction value is in the range 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) with steps of 0.5 dBm/Hz. Valid values are in the range 0 to 190 (0 to -95 dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value '0'. Note that the content of this object should be correlated with the subcarrier mask and with the RFI setup.
ROW msanDslPsdMaskDsRowStatus	1.3.6.1.4.1.1332.1.1.5.3.19.4.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanDslPsdMaskUsTable	1.3.6.1.4.1.1332.1.1.5.3.19.5		not-accessible	Management of Upstream PSD Mask (G997.1 #7.3.1.2.9 )
msanDslPsdMaskUsEntry	1.3.6.1.4.1.1332.1.1.5.3.19.5.1		not-accessible	Description.
OCT msanDslPsdMaskUsName	1.3.6.1.4.1.1332.1.1.5.3.19.5.1.1	OCTET STRING	not-accessible	Upstream custom PSD mask name.
INT msanDslPsdMaskUsType	1.3.6.1.4.1.1332.1.1.5.3.19.5.1.2	INTEGER	read-only	Downstream custom PSD mask type. Possible values: default(1) - Default mask prepared by vendor, user is not allowed to delete or change it configured(2) - Mask created by user
XDS msanDslPsdMaskUsShape	1.3.6.1.4.1.1332.1.1.5.3.19.5.1.3	Xdsl2PsdMaskUs	read-write	The upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 16 pairs of values in the following structure: Octets 0-1 - Index of the first subcarrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the subcarrier indicated in octets 0 and 1. Octets 3-5 - Same, for a second breakpoint. Octets 6-8 - Same, for a third breakpoint. This architecture continues until octets 9-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and NSCus-1. Each PSD reduction value is in the range 0 (0 dBm/Hz) to 255 (-127.5 dBm/Hz) with steps of 0.5 dBm/Hz. Valid values are in the range 0 to 190 (0 to -95 dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value '0'. Note that the content of this object should be correlated with the subcarrier mask and with the RFI setup.
ROW msanDslPsdMaskUsRowStatus	1.3.6.1.4.1.1332.1.1.5.3.19.5.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanDslSeltStatusTable	1.3.6.1.4.1.1332.1.1.5.3.19.6		not-accessible	Description.
msanDslSeltStatusEntry	1.3.6.1.4.1.1332.1.1.5.3.19.6.1		not-accessible	Description.
OCT msanDslSeltStatusNoiseType	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.1	OCTET STRING	read-only	Noise type.
I32 msanDslSeltStatusNoiseMrgDs	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.2	Integer32	read-only	Noise margin in DS direction. [0.1 dB]
I32 msanDslSeltStatusNoiseMrgUs	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.3	Integer32	read-only	Noise margin in US direction. [0.1 dB]
I32 msanDslSeltStatusNumTonesDs	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.4	Integer32	read-only	Number of tones used for SELT in DS direction.
I32 msanDslSeltStatusNumTonesUs	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.5	Integer32	read-only	Number of tones used for SELT in US direction.
I32 msanDslSeltStatusMaxRateDs	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.6	Integer32	read-only	Maximum Downstream capacity [kbps]
I32 msanDslSeltStatusMaxRateUs	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.7	Integer32	read-only	Maximum Upstream capacity [kbps]
OCT msanDslSeltStatusCableType	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.8	OCTET STRING	read-only	DSL line loop type.
I32 msanDslSeltStatusCableLenght	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.9	Integer32	read-only	DSL line loop lenght. [m]
I32 msanDslSeltStatusFitError	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.10	Integer32	read-only	DSL Line lenght fit error. [%]
INT msanDslSeltStatusLoopTermination	1.3.6.1.4.1.1332.1.1.5.3.19.6.1.11	INTEGER	read-only	Type of DSL line termination.
msanPortMirroring	1.3.6.1.4.1.1332.1.1.5.3.20
msanPortMirroringGlobal	1.3.6.1.4.1.1332.1.1.5.3.20.1
msanPortMirroringTable	1.3.6.1.4.1.1332.1.1.5.3.20.2		not-accessible	Description.
msanPortMirroringEntry	1.3.6.1.4.1.1332.1.1.5.3.20.2.1		not-accessible	Description.
I32 msanPortMirroringSessionId	1.3.6.1.4.1.1332.1.1.5.3.20.2.1.1	Integer32	not-accessible	The Session number of this mirroring entry.
INT msanPortMirroringAdminState	1.3.6.1.4.1.1332.1.1.5.3.20.2.1.2	INTEGER	read-write	The status of this port mirroring session.
I32 msanPortMirroringDestPort	1.3.6.1.4.1.1332.1.1.5.3.20.2.1.3	Integer32	read-write	The port which traffic from the mirrored ports will be sent to. Port value is ifIndex from ifTable. Value 0 means, port is not defined.
msanPortMirroringMemberTable	1.3.6.1.4.1.1332.1.1.5.3.20.3		not-accessible	Description.
msanPortMirroringMemberEntry	1.3.6.1.4.1.1332.1.1.5.3.20.3.1		not-accessible	Description.
I32 msanPortMirroringMemberSrcPort	1.3.6.1.4.1.1332.1.1.5.3.20.3.1.1	Integer32	not-accessible	The port from which traffic will be sent to the destination port.
INT msanPortMirroringMemberDirection	1.3.6.1.4.1.1332.1.1.5.3.20.3.1.2	INTEGER	read-create	The direction of the data to be mirrored on this source port.
ROW msanPortMirroringMemberRowStatus	1.3.6.1.4.1.1332.1.1.5.3.20.3.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanResetWithDelay	1.3.6.1.4.1.1332.1.1.5.3.21
msanResetWithDelayGlobal	1.3.6.1.4.1.1332.1.1.5.3.21.1
INT msanResetDelay	1.3.6.1.4.1.1332.1.1.5.3.21.1.1	INTEGER	read-write	Delay in seconds before reset will be performed. If set to 0, reset countdown is stopped and reset is cancelled. This parameter returns number of seconds before reset. If it returns 0, reset with delay was not initiated.
msanMacTable	1.3.6.1.4.1.1332.1.1.5.3.22
msanMacTableGlobal	1.3.6.1.4.1.1332.1.1.5.3.22.1
U32 msanMacTableLength	1.3.6.1.4.1.1332.1.1.5.3.22.1.1	Unsigned32	read-only	Maximum number of MAC addresses (total length of MAC table).
U32 msanMacTableUsed	1.3.6.1.4.1.1332.1.1.5.3.22.1.2	Unsigned32	read-only	Number of entries in MAC table.
msanMacTableCAMTable	1.3.6.1.4.1.1332.1.1.5.3.22.2		not-accessible	Description.
msanMacTableCAMEntry	1.3.6.1.4.1.1332.1.1.5.3.22.2.1		not-accessible	Description.
I32 msanMacTableCAMIndex	1.3.6.1.4.1.1332.1.1.5.3.22.2.1.1	Integer32	not-accessible	Id of the CAM entry.
MAC msanMacTableMacAddress	1.3.6.1.4.1.1332.1.1.5.3.22.2.1.2	MacAddress	read-only	MAC address of the CAM entry.
I32 msanMacTablePort	1.3.6.1.4.1.1332.1.1.5.3.22.2.1.3	Integer32	read-only	The port on which MAC address was learned or defined.
I32 msanMacTableVLAN	1.3.6.1.4.1.1332.1.1.5.3.22.2.1.4	Integer32	read-only	VLAN id of the learned or defined MAC address.
INT msanMacTableType	1.3.6.1.4.1.1332.1.1.5.3.22.2.1.5	INTEGER	read-only	Type of the MAC address.
msanAcs	1.3.6.1.4.1.1332.1.1.5.3.23
msanAcsGlobal	1.3.6.1.4.1.1332.1.1.5.3.23.1
OCT msanAcsServerUrl	1.3.6.1.4.1.1332.1.1.5.3.23.1.1	OCTET STRING	read-write	This is URL of the ACS server in form: http:///acs. If hostname is used, msanDnsIpAddress and msanAcsDomainName must also be set.
IP msanPrimaryDnsIpAddress	1.3.6.1.4.1.1332.1.1.5.3.23.1.2	IpAddress	read-write	This specifies the primary DNS server IP .
IP msanSecondaryDnsIpAddress	1.3.6.1.4.1.1332.1.1.5.3.23.1.3	IpAddress	read-write	This specifies the secondary DNS server IP .
OCT msanAcsDomainName	1.3.6.1.4.1.1332.1.1.5.3.23.1.4	OCTET STRING	read-write	Domain name.
INT msanAcsClientStatus	1.3.6.1.4.1.1332.1.1.5.3.23.1.5	INTEGER	read-write	ACS client administrative status.
INT msanAcsBackupConf	1.3.6.1.4.1.1332.1.1.5.3.23.1.6	INTEGER	read-write	Back up configuration (as CLI script) to ACS server.
msanStp	1.3.6.1.4.1.1332.1.1.5.3.24
msanStpGlobal	1.3.6.1.4.1.1332.1.1.5.3.24.1
msanStpBpduFilterTable	1.3.6.1.4.1.1332.1.1.5.3.24.2		not-accessible	Description.
msanStpBpduFilterEntry	1.3.6.1.4.1.1332.1.1.5.3.24.2.1		not-accessible	Description.
INT msanStpBpduFilter	1.3.6.1.4.1.1332.1.1.5.3.24.2.1.1	INTEGER	read-write	Defines how BPDU packets are handled in case stp_port_state is disabled. 0 disable - If stp_port_state is disabled on interface, forward all BPDUs unchanged to all other interfaces that also have stp_port_state disabled. 1 enable - If stp_port_state is disabled on interface, drop all BPDUs received on the interface.
msanStpSwitchConfigGroup	1.3.6.1.4.1.1332.1.1.5.3.24.3
U32 msanStpCstBridgePriority	1.3.6.1.4.1.1332.1.1.5.3.24.3.1	Unsigned32	read-write	The CSTP bridge priority in instance 0. The priority is in the increments of 4096. The recommended default value is 32768.
msanStpMstTable	1.3.6.1.4.1.1332.1.1.5.3.24.4		not-accessible	Description.
msanStpMstEntry	1.3.6.1.4.1.1332.1.1.5.3.24.4.1		not-accessible	Description.
U32 msanStpMstId	1.3.6.1.4.1.1332.1.1.5.3.24.4.1.1	Unsigned32	not-accessible	The MSTP instance ID. Instance 0 is not shown.
U32 msanStpMstBridgePriority	1.3.6.1.4.1.1332.1.1.5.3.24.4.1.2	Unsigned32	read-create	The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.
ROW msanStpMstRowStatus	1.3.6.1.4.1.1332.1.1.5.3.24.4.1.3	RowStatus	read-create	The MSTP instance status. Instance 0 is not shown. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.
msanStpMstVlanTable	1.3.6.1.4.1.1332.1.1.5.3.24.5		not-accessible	Description.
msanStpMstVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.24.5.1		not-accessible	Description.
ROW msanStpMstVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.24.5.1.1	RowStatus	read-create	The association status of an MSTP instance and a VLAN. Instance 0 is not shown. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.
msanStpMstPortTable	1.3.6.1.4.1.1332.1.1.5.3.24.6		not-accessible	MST port table.
msanStpMstPortEntry	1.3.6.1.4.1.1332.1.1.5.3.24.6.1		not-accessible	MST port entry.
U32 msanStpMstPortPathCost	1.3.6.1.4.1.1332.1.1.5.3.24.6.1.1	Unsigned32	read-write	The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed. Instance 0 is not shown.
U32 msanStpMstPortPriority	1.3.6.1.4.1.1332.1.1.5.3.24.6.1.2	Unsigned32	read-write	The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128. Instance 0 is not shown.
msanStpPortTable	1.3.6.1.4.1.1332.1.1.5.3.24.7		not-accessible	Description.
msanStpPortEntry	1.3.6.1.4.1.1332.1.1.5.3.24.7.1		not-accessible	Description.
I32 msanStpPortHelloTime	1.3.6.1.4.1.1332.1.1.5.3.24.7.1.1	Integer32	read-write	Hello time for the STP port. The default value is 0 (Not configured).
msanStpCstPortTable	1.3.6.1.4.1.1332.1.1.5.3.24.8		not-accessible	Description.
msanStpCstPortEntry	1.3.6.1.4.1.1332.1.1.5.3.24.8.1		not-accessible	Description.
U32 msanStpCstPortPathCost	1.3.6.1.4.1.1332.1.1.5.3.24.8.1.1	Unsigned32	read-write	The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.
U32 msanStpCstExtPortPathCost	1.3.6.1.4.1.1332.1.1.5.3.24.8.1.2	Unsigned32	read-write	The MSTP external port path cost in CIST. The default value varies depending upon the link speed.
msanAuthentication	1.3.6.1.4.1.1332.1.1.5.3.25
msanAuthenticationGlobal	1.3.6.1.4.1.1332.1.1.5.3.25.1
STR msanAuthenticationListCreate	1.3.6.1.4.1.1332.1.1.5.3.25.2	DisplayString	read-write	Authentication List Create If set to a non empty string, creates a new Authentication List for configuration.
msanAuthenticationListTable	1.3.6.1.4.1.1332.1.1.5.3.25.3		not-accessible	Description.
msanAuthenticationListEntry	1.3.6.1.4.1.1332.1.1.5.3.25.3.1		not-accessible	Description.
STR msanAuthenticationListName	1.3.6.1.4.1.1332.1.1.5.3.25.3.1.1	DisplayString	not-accessible	Authenticaiton List Name Unique name used to identify the Authentication List from other tables.
INT msanAuthenticationListMethod1	1.3.6.1.4.1.1332.1.1.5.3.25.3.1.2	INTEGER	read-create	Authenticion List Method 1 Configures the first authentication method to use when this list is specified.
INT msanAuthenticationListMethod2	1.3.6.1.4.1.1332.1.1.5.3.25.3.1.3	INTEGER	read-create	Authenticion List Method 2 Configures the second authentication method to use when this list is specified.
INT msanAuthenticationListMethod3	1.3.6.1.4.1.1332.1.1.5.3.25.3.1.4	INTEGER	read-create	Authenticion List Method 3 Configures the third authentication method to use when this list is specified.
ROW msanAuthenticationListStatus	1.3.6.1.4.1.1332.1.1.5.3.25.3.1.5	RowStatus	read-create	The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List createAndGo (4) destroy(6) - removes the Authentication List.
msanPortSecurity	1.3.6.1.4.1.1332.1.1.5.3.26
msanPortSecurityGlobal	1.3.6.1.4.1.1332.1.1.5.3.26.1
msanPortSecurityStatMacTable	1.3.6.1.4.1.1332.1.1.5.3.26.2		not-accessible	Description.
msanPortSecurityStatMacEntry	1.3.6.1.4.1.1332.1.1.5.3.26.2.1		not-accessible	Description.
I32 msanPortSecurityStatMacIf	1.3.6.1.4.1.1332.1.1.5.3.26.2.1.1	Integer32	not-accessible	Unique numerical identification of the interface.
INT msanPortSecurityStatMacVlanId	1.3.6.1.4.1.1332.1.1.5.3.26.2.1.2	INTEGER	not-accessible	VLAN identification.
MAC msanPortSecurityStatMacMacAddress	1.3.6.1.4.1.1332.1.1.5.3.26.2.1.3	MacAddress	not-accessible	Statically locked MAC addresses for port.
ROW msanPortSecurityStatMacRowStatus	1.3.6.1.4.1.1332.1.1.5.3.26.2.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanPortSecurityPortVlanTable	1.3.6.1.4.1.1332.1.1.5.3.26.3		not-accessible	Description.
msanPortSecurityPortVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.26.3.1		not-accessible	Description.
I32 msanPortSecurityPortVlanDynamicLimit	1.3.6.1.4.1.1332.1.1.5.3.26.3.1.1	Integer32	read-write	The limit of dynamically learned MAC addresses per vlan on selected port.
ROW msanPortSecurityPortVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.26.3.1.2	RowStatus	read-write	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanLag	1.3.6.1.4.1.1332.1.1.5.3.27
msanLagGlobal	1.3.6.1.4.1.1332.1.1.5.3.27.1
msanLagDetailedConfigTable	1.3.6.1.4.1.1332.1.1.5.3.27.2		not-accessible	A detailed table of the switch's LAG config entries.
msanLagDetailedConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.27.2.1		not-accessible	Switch's LAG config entry
I32 msanLagDetailedLagIndex	1.3.6.1.4.1.1332.1.1.5.3.27.2.1.1	Integer32	not-accessible	LAG index
I32 msanLagDetailedIfIndex	1.3.6.1.4.1.1332.1.1.5.3.27.2.1.2	Integer32	not-accessible	LAG port index
OID msanLagDetailedPortSpeed	1.3.6.1.4.1.1332.1.1.5.3.27.2.1.3	OBJECT IDENTIFIER	read-create	LAG port speed. See agentPortType for a description and list of valid values.
INT msanLagDetailedPortStatus	1.3.6.1.4.1.1332.1.1.5.3.27.2.1.4	INTEGER	read-only	LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.
ROW msanLagDetailedRowStatus	1.3.6.1.4.1.1332.1.1.5.3.27.2.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanLagTable	1.3.6.1.4.1.1332.1.1.5.3.27.3		not-accessible	Config table of additional LAG parameters.
msanLagEntry	1.3.6.1.4.1.1332.1.1.5.3.27.3.1		not-accessible	Description.
I32 msanLagIndex	1.3.6.1.4.1.1332.1.1.5.3.27.3.1.1	Integer32	not-accessible	LAG index. Value corresponds to ifIndex for LAG interfaces in ifTable.
I32 msanLagMaxFrameSize	1.3.6.1.4.1.1332.1.1.5.3.27.3.1.2	Integer32	read-write	This object identifies the currently configured maximum frame size value for this LAG interface.
INT msanLagDVlanTagMode	1.3.6.1.4.1.1332.1.1.5.3.27.3.1.3	INTEGER	read-write	Controls the Double Vlan Tag mode on this LAG interface.
msanRadiusServer	1.3.6.1.4.1.1332.1.1.5.3.28
msanRadiusServerGlobal	1.3.6.1.4.1.1332.1.1.5.3.28.1
msanRadiusServerConfigTable	1.3.6.1.4.1.1332.1.1.5.3.28.2		not-accessible	Table with information about Radius Authentication Server IP Addresses, port numbers and shared secret
msanRadiusServerConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.28.2.1		not-accessible	Entry consisting of configuration data for a Radius Authentication Server.
IP msanRadiusServerAddress	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.1	IpAddress	not-accessible	IP Address of the configured RADIUS server. This object cannot be changed after creation.
U32 msanRadiusServerPort	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.2	Unsigned32	read-write	Port number for the RADIUS server.
STR msanRadiusServerSecret	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.3	DisplayString	read-write	Configured shared sercret for the RADIUS server.
INT msanRadiusServerPrimaryMode	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.4	INTEGER	read-write	Configure the RADIUS server to be the primary server. If there is any other server that is configured to be primary, that server is set to be a seconday server and this entry is set Primary.
INT msanRadiusServerCurrentMode	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.5	INTEGER	read-only	Indicate if the RADIUS server is the current server in user for authentication.
INT msanRadiusServerMsgAuth	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.6	INTEGER	read-write	Enable or disable the message authenticator attribute for this RADIUS server.
ROW msanRadiusServerStatus	1.3.6.1.4.1.1332.1.1.5.3.28.2.1.7	RowStatus	read-create	Creates or destroys a RADIUS Authentication server entry. active(1) - This entry is active. createAndGo(4) - Creates a new entry. destroy(6) - Deletes an entry.
msanNetwork	1.3.6.1.4.1.1332.1.1.5.3.29
msanNetworkGlobal	1.3.6.1.4.1.1332.1.1.5.3.29.1
IP msanNetworkIPAddress	1.3.6.1.4.1.1332.1.1.5.3.29.1.1	IpAddress	read-write	The switch's network ip address
IP msanNetworkSubnetMask	1.3.6.1.4.1.1332.1.1.5.3.29.1.2	IpAddress	read-write	The switch's network subnet mask
IP msanNetworkDefaultGateway	1.3.6.1.4.1.1332.1.1.5.3.29.1.3	IpAddress	read-write	The switch's network default gateway
IP msanNetworkDhcpSrvIpAddr	1.3.6.1.4.1.1332.1.1.5.3.29.1.4	IpAddress	read-only	IP address of DHCP server used by DHCP client.
INT msanNetworkDhcpSrvVendorSpecific	1.3.6.1.4.1.1332.1.1.5.3.29.1.5	INTEGER	read-write	DHCP client uses only vendor specific DHCP servers (when client sends opt. 60 to server, it should return expected vendor specific value in opt. 43)
OCT msanNetworkDhcpClientLeaseObtained	1.3.6.1.4.1.1332.1.1.5.3.29.1.6	OCTET STRING	read-only	The date and time when DHCP lease was obtained.
OCT msanNetworkDhcpClientLeaseExpires	1.3.6.1.4.1.1332.1.1.5.3.29.1.7	OCTET STRING	read-only	The date and time for which the DHCP lease is valid.
INT msanNetworkDhcpClientLocalOpt82	1.3.6.1.4.1.1332.1.1.5.3.29.1.8	INTEGER	read-write	DHCP client adds relay agent information option into its own outgoing frames.
msanNetworkDhcpClientVlanTable	1.3.6.1.4.1.1332.1.1.5.3.29.2		not-accessible	DHCP client configuration per vlan id.
msanNetworkDhcpClientVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.29.2.1		not-accessible	Description.
INT msanNetworkDhcpClientVlanLocalOpt82	1.3.6.1.4.1.1332.1.1.5.3.29.2.1.1	INTEGER	read-write	DHCP client on specified vlan adds relay agent information option into its own outgoing frames.
msanStormControl	1.3.6.1.4.1.1332.1.1.5.3.30
msanStormControlGlobal	1.3.6.1.4.1.1332.1.1.5.3.30.1
msanPortStormControlTable	1.3.6.1.4.1.1332.1.1.5.3.30.2		not-accessible	Description.
msanPortStormControlEntry	1.3.6.1.4.1.1332.1.1.5.3.30.2.1		not-accessible	Description.
INT msanPortBroadcastControlMode	1.3.6.1.4.1.1332.1.1.5.3.30.2.1.1	INTEGER	read-write	he switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic.
I32 msanPortBroadcastControlThreshold	1.3.6.1.4.1.1332.1.1.5.3.30.2.1.2	Integer32	read-write	Specify the data rate at which broadcast storm control activates (packets per second)
INT msanPortMulticastControlMode	1.3.6.1.4.1.1332.1.1.5.3.30.2.1.3	INTEGER	read-write	The switch config multicast allows you to enable or disable multicast storm recovery mode. When you specify Enable for multicast Storm Recovery and the multicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic
I32 msanPortMulticastControlThreshold	1.3.6.1.4.1.1332.1.1.5.3.30.2.1.4	Integer32	read-write	Specify the data rate at which multicast storm control activates (packets per second)
INT msanPortUnicastControlMode	1.3.6.1.4.1.1332.1.1.5.3.30.2.1.5	INTEGER	read-write	The switch config unicast allows you to enable or disable unicast storm recovery mode. When you specify Enable for unicast Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic.
I32 msanPortUnicastControlThreshold	1.3.6.1.4.1.1332.1.1.5.3.30.2.1.6	Integer32	read-write	Specify the data rate at which unicast storm control activates (packets per second)
msanUserConfig	1.3.6.1.4.1.1332.1.1.5.3.31
msanUserConfigGlobal	1.3.6.1.4.1.1332.1.1.5.3.31.1
OCT msanUserConfigCheckPassword	1.3.6.1.4.1.1332.1.1.5.3.31.1.1	OCTET STRING	read-write	Parameter is used to check user's password. String must be written in next format: user_name password First blank space is used as delimeter between user_name and password. If password is not valid or user is not configured, inconsistentValue(12)error code will be returned.
msanUserConfigTable	1.3.6.1.4.1.1332.1.1.5.3.31.2		not-accessible	Description.
msanUserConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.31.2.1		not-accessible	Description.
I32 msanUserIndex	1.3.6.1.4.1.1332.1.1.5.3.31.2.1.1	Integer32	not-accessible	User Config Index
INT msanUserAccessMode	1.3.6.1.4.1.1332.1.1.5.3.31.2.1.2	INTEGER	read-write	User Access Mode
msanSfp	1.3.6.1.4.1.1332.1.1.5.3.32
msanSfpGlobal	1.3.6.1.4.1.1332.1.1.5.3.32.1
msanSfpInfoTable	1.3.6.1.4.1.1332.1.1.5.3.32.2		not-accessible	Description.
msanSfpInfoEntry	1.3.6.1.4.1.1332.1.1.5.3.32.2.1		not-accessible	Description.
INT msanSfpInfoState	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.1	INTEGER	read-only	Module state value on port. Ports which support SFP module are from 1 to 10 and from 15 to 28. State value adminOff means that specific port is administrative disabled and we can not read data from module on that port. Operational state means that SFP module is present and it works perfect. State operWithAl(operational with alarm) means that SFP module is present, but it works with internal alarms. Loss(Loss of signal) state means that SFP module is present but it have loss of signal. PresNoDiag(Present, no diagnostic) state means that SFP module is present but diagnostic is not supported. NotAvaliable state means that admin. mode of specific port has disabled value and SFP state is not avaliable. NotPresent state means that SFP module is not present.
INT msanSfpInfoInterfaceType	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.2	INTEGER	read-only	Transceiver(module) type. Module type can be SFP, NOT(mudule type is not SFP), NO(no module on port), AD(admin. disabled port) and XFP.
I32 msanSfpInfoNominalBitrate	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.3	Integer32	read-only	Module(SFP) nominal bitrate value measure in Mbit/s. If parameter is not available, value -1 is used.
OCT msanSfpInfoNominalRange	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.4	OCTET STRING	read-only	Module(SFP) nominal range value. Nominal range value can support five different link lengths. Link length value and nominal range units are defined depends on value of nominal range. We can get link length value which can support 9/125 um fiber and nominal range measure in km units. We can get link length value which can support 9/125 um fiber and nominal range measure in 100m units. We can get link length value which can support 50/125 um fiber and nominal range measure in 10m units. We can get link length value which can support 62,5/125 um fiber and nominal range measure in 10m units. We can get link length value which can support cooper and nominal range measure in m units.
OCT msanSfpInfoVendor	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.5	OCTET STRING	read-only	Module(SFP) vendor name.
I32 msanSfpInfoIeeeVendorId	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.6	Integer32	read-only	Module(SFP) vendor IEEE company ID. If parameter is not available, value -1 is used.
OCT msanSfpInfoPartNr	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.7	OCTET STRING	read-only	Module(SFP) part number.
OCT msanSfpInfoRevisionNr	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.8	OCTET STRING	read-only	Module(SFP) revision number.
OCT msanSfpInfoSerialNr	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.9	OCTET STRING	read-only	Module(SFP) serial number.
OCT msanSfpInfoManufacturingDate	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.10	OCTET STRING	read-only	Module(SFP) manufacturing date.
I32 msanSfpInfoWavelength	1.3.6.1.4.1.1332.1.1.5.3.32.2.1.11	Integer32	read-only	Module(SFP) laser wavelength measure in nanometers. If parameter is not available, value -1 is used.
msanSfpDiagnosticsTable	1.3.6.1.4.1.1332.1.1.5.3.32.3		not-accessible	Description.
msanSfpDiagnosticsEntry	1.3.6.1.4.1.1332.1.1.5.3.32.3.1		not-accessible	Description.
INT msanSfpDiagnosticsSignal	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.1	INTEGER	read-only	Module(SFP) signal value. If diagnostic for SFP module is supported than value can be OK(signal is ok) or loss(loss of signal), in the other case the value is set on notSupported becouse diagnostic is not supported(-1).
I32 msanSfpDiagnosticsTempCurrent	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.2	Integer32	read-only	Current SFP module temperature value in [deg C]. If diagnostic is not supported for SFP module then current temperature is set on not supported value(-129).
I32 msanSfpDiagnosticsTempMin	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.3	Integer32	read-only	SFP module minimum temperature threshold limit in [deg C]. If diagnostic is not supported for SFP module then minimum temperature threshold limit is set on not supported value(-129).
I32 msanSfpDiagnosticsTempMax	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.4	Integer32	read-only	SFP module maximum temperature threshold limit in [deg C]. If diagnostic is not supported for SFP module then maximum temperature threshold limit is set on not supported value(-129).
I32 msanSfpDiagnosticsVoltageCurrent	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.6	Integer32	read-only	Current SFP module supply voltage value in [V]. If diagnostic is not supported for SFP module then current supply voltage is set on not supported value(-1).
I32 msanSfpDiagnosticsVoltageMin	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.7	Integer32	read-only	SFP module minimum supply voltage threshold limit in [V]. If diagnostic is not supported for SFP module then minimum supply voltage threshold limit is set on not supported value(-1).
I32 msanSfpDiagnosticsVoltageMax	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.8	Integer32	read-only	SFP module maximum supply voltage threshold limit in [V]. If diagnostic is not supported for SFP module then maximum supply voltage threshold limit is set on not supported value(-1).
I32 msanSfpDiagnosticsTxBiasCrrCurrent	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.9	Integer32	read-only	Current SFP module Tx Bias Current value in [mA]. If diagnostic is not supported for SFP module then current Tx Bias Current is set on not supported value(-1).
I32 msanSfpDiagnosticsTxBiasCrrMin	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.10	Integer32	read-only	SFP module minimum Tx Bias Current threshold limit in [mA]. If diagnostic is not supported for SFP module then minimum Tx Bias Current threshold limit is set on not supported value(-1).
I32 msanSfpDiagnosticsTxBiasCrrMax	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.11	Integer32	read-only	SFP module maximum Tx Bias Current threshold limit in [mA]. If diagnostic is not supported for SFP module then maximum Tx Bias Current threshold limit is set on not supported value(-1).
I32 msanSfpDiagnosticsTxPowerCurrent	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.12	Integer32	read-only	Current SFP module transmitted optical output power value in [mW]. If diagnostic is not supported for SFP module then current transmitted optical output power is set on not supported value(-1).
I32 msanSfpDiagnosticsTxPowerMin	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.13	Integer32	read-only	SFP module minimum transmitted optical output power threshold limit in [mW]. If diagnostic is not supported for SFP module then minimum transmitted optical output power is set on not supported value(-1).
I32 msanSfpDiagnosticsTxPowerMax	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.14	Integer32	read-only	SFP module maximum transmitted optical output power threshold limit in [mW]. If diagnostic is not supported for SFP module then maximum transmitted optical output power is set on not supported value(-1).
I32 msanSfpDiagnosticsRxPowerCurrent	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.15	Integer32	read-only	Current SFP module received optical input power value in [mW]. If diagnostic is not supported for SFP module then current received optical input power is set on not supported value(-1).
I32 msanSfpDiagnosticsRxPowerMin	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.16	Integer32	read-only	SFP module minimum received optical input power threshold limit in [mW]. If diagnostic is not supported for SFP module then minimum received optical input power is set on not supported value(-1).
I32 msanSfpDiagnosticsRxPowerMax	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.17	Integer32	read-only	SFP module maximum received optical input power threshold limit in [mW]. If diagnostic is not supported for SFP module then maximum received optical input power is set on not supported value(-1).
INT msanSfpDiagnosticsTempStatus	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.19	INTEGER	read-only	Temperature alarm status.
INT msanSfpDiagnosticsVoltageStatus	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.20	INTEGER	read-only	Voltage alarm status.
INT msanSfpDiagnosticsTxBiasStatus	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.21	INTEGER	read-only	TX bias alarm status.
INT msanSfpDiagnosticsTxPowerStatus	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.22	INTEGER	read-only	TX power alarm status.
INT msanSfpDiagnosticsRxPowerStatus	1.3.6.1.4.1.1332.1.1.5.3.32.3.1.23	INTEGER	read-only	RX power alarm status.
msanMacSg	1.3.6.1.4.1.1332.1.1.5.3.34
msanMacSgGlobal	1.3.6.1.4.1.1332.1.1.5.3.34.1
INT msanMacSgStatus	1.3.6.1.4.1.1332.1.1.5.3.34.1.1	INTEGER	read-write	Administrative state of MAC Source Guard on the system.
msanMacSgPortTable	1.3.6.1.4.1.1332.1.1.5.3.34.2		not-accessible	Description.
msanMacSgPortEntry	1.3.6.1.4.1.1332.1.1.5.3.34.2.1		not-accessible	Description.
INT msanMacSgPortStatus	1.3.6.1.4.1.1332.1.1.5.3.34.2.1.1	INTEGER	read-write	Administrative state of MAC Source Guard on interface.
I32 msanMacSgPortViolationsCounter	1.3.6.1.4.1.1332.1.1.5.3.34.2.1.2	Integer32	read-only	MAC Source Guard Violations counter
msanErrorDisable	1.3.6.1.4.1.1332.1.1.5.3.35
msanErrorDisableGlobal	1.3.6.1.4.1.1332.1.1.5.3.35.1
I32 msanErrorDisableInterval	1.3.6.1.4.1.1332.1.1.5.3.35.1.1	Integer32	read-write	The interval in minutes that will pass since error-disabled interface will be enabled. This parameter has effect only if ErrorDisable Recovery is enabled.
INT msanErrorDisableMacSgDetectionStatus	1.3.6.1.4.1.1332.1.1.5.3.35.1.2	INTEGER	read-write	Administrative state of ErrorDisable Detection for MAC Source Guard cause. If enabled, interface will be error-disabled when MAC Source Guard violation is detected.
INT msanErrorDisableMacSgRecoveryStatus	1.3.6.1.4.1.1332.1.1.5.3.35.1.3	INTEGER	read-write	Administrative state of ErrorDisable Recovery for MAC Source Guard cause. If enabled, interface will be automatically recovered when error-disabled due to MAC Source Guard violation.
msanErrorDisablePortTable	1.3.6.1.4.1.1332.1.1.5.3.35.2		not-accessible	Description.
msanErrorDisablePortEntry	1.3.6.1.4.1.1332.1.1.5.3.35.2.1		not-accessible	Description.
INT msanErrorDisablePortStatus	1.3.6.1.4.1.1332.1.1.5.3.35.2.1.1	INTEGER	read-only	This parameter shows which interfaces are in errorDisable(2) recovery administrative state.
OCT msanErrorDisablePortCause	1.3.6.1.4.1.1332.1.1.5.3.35.2.1.2	OCTET STRING	read-only	Cause for errorDisable(2) status on interface.
I32 msanErrorDisablePortTimeLeft	1.3.6.1.4.1.1332.1.1.5.3.35.2.1.3	Integer32	read-only	Time in seconds which defines how much time left for interface to stay in errorDisable(2) state.
I32 msanErrorDisablePortCounter	1.3.6.1.4.1.1332.1.1.5.3.35.2.1.4	Integer32	read-only	The number of times the specified interface has been in errorDisable(2) state.
msanAdsl	1.3.6.1.4.1.1332.1.1.5.3.36
msanAdslGlobal	1.3.6.1.4.1.1332.1.1.5.3.36.1
msanAdslAtucPhysExtnTable	1.3.6.1.4.1.1332.1.1.5.3.36.2		not-accessible	This table provides one row for each ATUC. This table is an extention to adslAtucPhysTable defined in rfc-2662.
msanAdslAtucPhysExtnEntry	1.3.6.1.4.1.1332.1.1.5.3.36.2.1		not-accessible	An entry (conceptual row) in the msanAdslAtucPhysExtnTable. The Table is indexed by ifIndex.
INT msanAdslAtucPhysExtnOpState	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.1	INTEGER	read-only	This object indicates the operational state of the ATU. Values include idle, handshake, training, etc.
INT msanAdslAtucPhysExtnActualStd	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.2	INTEGER	read-only	This object provides actual ATU-C configuration based on outcome of negotiation with ATU-R. In this case, the parameter provides actual standard used for the connection.
I32 msanAdslAtucPhysExtnBertError	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.3	Integer32	read-only	This object indicates the No. of bit errors detected during BERT.
C32 msanAdslAtucPhysExtnTxAtmCellCounter	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.4	Counter32	read-only	This object Provides transmit ATM cell counter.
I32 msanAdslAtucPhysExtnRxAtmCellCounter	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.5	Integer32	read-only	This object Provides receive ATM cell counter.
I32 msanAdslAtucPhysExtnStartProgress	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.6	Integer32	read-only	This object provides current detailed start up information to be used for debugging.
I32 msanAdslAtucPhysExtnIdleBertError	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.7	Integer32	read-only	Number of bit errors.
I32 msanAdslAtucPhysExtnIdleBertCells	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.8	Integer32	read-only	Number of idle cells.
INT msanAdslAtucPhysExtnBertSync	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.9	INTEGER	read-only	Indicates if the Signal is in Sync or not.
INT msanAdslAtucPhysExtnParametricTestResult	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.10	INTEGER	read-only	Indicates the Result of the Parametric Test conducted on the Xcvr.
INT msanAdslAtucPhysExtnSeltInfoValid	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.11	INTEGER	read-only	Indicates the information validity for the SELT operation conducted on the Xcvr.
I32 msanAdslAtucPhysExtnSeltLoopLen	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.12	Integer32	read-only	Indicates the LOOP Length in Feet once when the SELT information is valid on the Xcvr.
INT msanAdslAtucPhysExtnSeltLoopEnd	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.13	INTEGER	read-only	Indicates whether the loop is short or open once when the SELT information is valid on the Xcvr.
INT msanAdslAtucPhysExtnSeltLoopGauge	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.14	INTEGER	read-only	Indicates the LOOP wire_gauge information once when the SELT information is valid on the Xcvr.
G32 msanAdslAtucPhysExtnSeltUpShannonCap	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.15	Gauge32	read-only	Indicates the LOOP Upstream Shannon Capacity (in bps) once when the SELT information is valid on the Xcvr.
G32 msanAdslAtucPhysExtnSeltDownShannonCap	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.16	Gauge32	read-only	Indicates the LOOP Downstream Shannon Capacity (in bps) once when the SELT information is valid on the Xcvr.
OCT msanAdslAtucPhysExtnSeltInbandNoise	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.17	OCTET STRING	read-only	512 values that indicate inband noise length in dBM/Hz, covering both bands from 0 to 1.1 MHz.
OCT msanAdslAtucPhysExtnSeltTerminationResp	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.18	OCTET STRING	read-only	180 discrete values that indicate termination response magnitude from 0 to 18Kft.
OCT msanAdslAtucPhysExtnSeltUpMgnAtRate	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.19	OCTET STRING	read-only	300 values that indicate SNR margin in dB/10 at a particular rate are provided, at 100K increments, up to 15 Mbps.
OCT msanAdslAtucPhysExtnSeltDownMgnAtRate	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.20	OCTET STRING	read-only	300 values that indicate SNR margin in dB/10 at a particular rate are provided, at 100K increments, up to 15 Mbps.
INT msanAdslAtucPhysExtnDataBoostStatus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.21	INTEGER	read-only	This object indicates whether DataBoost is utilized for the connection.
OCT msanAdslAtucPhysExtnTestArray	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.22	OCTET STRING	read-only	This object indicates the Parametric Test Array. Every Four octets refer to one element in this array of octets.
I32 msanAdslAtucPhysExtnChanPerfCD	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.23	Integer32	read-only	The near-end delineated total cell count performance parameter is a count of the total number of cells passed through the cell delineation and HEC function process operating on the ATM Data Path while in the SYNC state. (Not available for ADSL).
I32 msanAdslAtucPhysExtnChanPerfBE	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.24	Integer32	read-only	The near-end idle bit error count performance parameter is a count of the number of bit errors in the idle cell payload received in the ATM Data Path at the near-end. (Not available for ADSL).
I32 msanAdslAtucPhysExtnDeltHLINSCus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.25	Integer32	read-only	DELT-related parameter that provides the scale factor to be applied to the upstream Hlin(f) values.(Not available for ADSL and ADSL2plus).
OCT msanAdslAtucPhysExtnDeltHLINpsus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.26	OCTET STRING	read-only	DELT-related parameter that provides an array of complex upstream Hlin(f) values in linear scale. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets.
I32 msanAdslAtucPhysExtnDeltHLOGMTus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.27	Integer32	read-only	DELT-related parameter that provides the number of symbols used to measure the upstream Hlog(f).(Not available for ADSL and ADSL2plus).
OCT msanAdslAtucPhysExtnDeltHLOGpsus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.28	OCTET STRING	read-only	DELT-related parameter that provides an array of real upstream Hlog(f) values in dB. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets.
I32 msanAdslAtucPhysExtnDeltQLNMTus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.29	Integer32	read-only	DELT-related parameter that provides the number of symbols used to measure the upstream QLN(f) values. (Not available for ADSL and ADSL2plus).
OCT msanAdslAtucPhysExtnDeltQLNpsus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.30	OCTET STRING	read-only	DELT-related parameter that provides an array of real upstream QLN(f) values in dB. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets.
INT msanAdslAtucPhysExtnDeltLastTxState	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.31	INTEGER	read-only	DELT-related parameter that provides last successful transmitted initialization state by the ATU-C. (Not available for ADSL and ADSL2plus).
INT msanAdslAtucPhysExtnPMState	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.32	INTEGER	read-only	Line Power Management State. (Not available for ADSL).
I32 msanAdslAtucPhysExtnChanPerfCU	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.33	Integer32	read-only	The near-end user total cell count performance parameter is a count of the total number of cells in the ATM Data Path delivered at the V-C (for ATU-C) or T-R (for ATU-R) interface. (Not available for ADSL).
T/F msanAdslAtucPhysExtnExtendedPsdStatus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.34	TruthValue	read-only	Conexant parameter that indicates whether an extended upstream PSD is used - for G.Span Plus mode of operation only. Only supported for G.Span Plus, therefore this parameter is not valid for ADSL2/ADSL2plus modes of operation.
I32 msanAdslAtucPhysExtnChipVersion	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.35	Integer32	read-only	Conexant parameter that indicates the DSP version number.
I32 msanAdslAtucPhysExtnPilotTone	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.36	Integer32	read-only	Conexant parameter that indicates the Pilot Tone Index.
G32 msanAdslAtucMSGds	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.37	Gauge32	read-only	Indicates the Overhead Channel. This feature is not supported by DSLPHY as yet.
INT msanAdslAtucPhysExtnPsdMaskMode	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.38	INTEGER	read-only	Conexant parameter that indicates the actual Psd Mask currently being used.
I32 msanAdslAtucPhysExtnDeltSNRMTus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.39	Integer32	read-only	DELT-related parameter that provides the number of symbols used to measure the upstream SNR(f) values. (Not available for ADSL and ADSL2plus)
INT msanAdslAtucPhysExtnDeltCurrStatus	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.40	INTEGER	read-only	This Conexant parameter indicates the current status of Atuc Line in DELT mode.
I32 msanAdslAtucSATN	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.41	Integer32	read-only	DELT-related parameter that provides the upstream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). For further details, Refer to Section 7.5.1.9 Revised Recommendation G.997.1.
OCT msanAdslAtucPhysExtnSystemVendorId	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.42	OCTET STRING	read-only	Indicates the Vendor ID as inserted by the ATU-C in the Overhead Messages(ADSL2). Typically identifies the ATU-C system integrator which usually refers to the vendor of the smallest field-replaceable unit. ATU-C System Vendor ID may not be the same as ATU-C Vendor ID. It is not available for ADSL. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number.
G32 msanAdslAtucPhysExtnSelfTestResult	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.43	Gauge32	read-only	Defines the ATU-C selftest result. The most significant octet is: 00 hex if the self-test passed or 01 hex if the self-test failed. Interpretation of the other octets is vendor discretionary and can be interpreted in combination with G.994.1 and system Vendor IDs. For further details, refer to Section 7.4.9 Revised Recommendation G.997.1.
OCT msanAdslAtucPhysExtnG9941VendorId	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.44	OCTET STRING	read-only	Indicates the Vendor ID as inserted by the ATU-C in the G.994.1 CL message. Typically identifies the vendor of the ATU-C G.994.1 functionality. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number. For further details, refer to Section 7.4.1 Revised Recommendation G.997.1.
OCT msanAdslAtucPhysExtnTsspsUs	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.45	OCTET STRING	read-only	This parameter provides the Upstream Transmit Spectrum Shaping parameter expressed as the set of break points exchanged during G994.1. Each breakpoint consists in a subcarrier index and the associated shaping parameter. Value of this parameter is in range 0 - 127, in multiples of -0.5 dB. 127 is a special value indicating the subcarrier is not transmitted. It is available only for ADSL2/ADSL2plus.For further details, Refer to Section 7.5.1.21.5 Revised Recommendation G.997.1.
I32 msanAdslAtucPhysExtnActPsdUs	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.46	Integer32	read-only	This parameter defines the average upstream transmit power spectrum density over the used subcarriers delivered by the ATU-C at the U-C reference point, at the instant of measurement. It's value ranges from -90 to 0, in 0.1 dB/Hz steps. It is available only for ADSL2/ADSL2plus. For further details, Refer to Section 7.5.1.14 Revised Recommendation G.997.1.
OCT msanAdslAtucPhysExtnGainspsUs	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.47	OCTET STRING	read-only	This parameter defines the upstream gains allocation table per subcarrier. It is an array of integer values in the 0 to 4093 range for subcarriers 0 to NSCus-1. The gain value is represented as a multiple of 1/512 on linear scale. It is supported for ADSL2/ADSl2plus only.
I32 msanAdslAtucPhysExtnStartBin	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.48	Integer32	read-only	This Gspan++ parameter indicates the start bin of the bit loading up array.
INT msanAdslAtucPhysExtnStartupErrorCode	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.49	INTEGER	read-only	Conexant parameter which indicates the startup error code.
U32 msanAdslAtucPhysExtnBitSwapCount	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.50	Unsigned32	read-only	This Conexant parameter indicates the bit swap count. It can read only in data mode
INT msanAdslAtucPhysExtnModPhase	1.3.6.1.4.1.1332.1.1.5.3.36.2.1.51	INTEGER	read-only	Conexant parameter to monitor the status of MoD
msanAdslLineExtnTable	1.3.6.1.4.1.1332.1.1.5.3.36.3		not-accessible	This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. This Table is an extension to adslLineTable defined in rfc-2662.
msanAdslLineExtnEntry	1.3.6.1.4.1.1332.1.1.5.3.36.3.1		not-accessible	An entry (conceptual row) in the msanAdslLineExtnTable. The Table is indexed by ifIndex.
INT msanAdslLineExtnAction	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.1	INTEGER	read-write	this object indicates parameter that allows actions on a per line basis. These actions include abort, startup, and tests.
INT msanAdslLineExtnUtopiaL2RxAddr	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.2	INTEGER	read-only	This object indicates UTOPIA Level 2 Rx address for a line.
INT msanAdslLineExtnUtopiaL2TxAddr	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.3	INTEGER	read-only	This object indicates UTOPIA Level 2 Tx address for a line.
BIT msanAdslLineExtnTransAtucCap	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.4	Bits	read-only	The transmission modes that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment. REFERENCE Section 7.3.2 ITU G.997.1.
BIT msanAdslLineExtnTransAtucActual	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.5	Bits	read-only	The transmission mode of the ATU-C. This object returns if there is no mode currently known. The initialization with the ATU-R will determine the mode used. REFERENCE Section 7.3.2 ITU G.997.1.
INT msanAdslLineExtnClockType	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.6	INTEGER	read-only	This object indicates parameter to set use of either crystal or oscillator.
INT msanAdslLineExtnLineDmtTrellis	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.7	INTEGER	read-only	Parameter that indicates whether trellis coding has been enabled or disabled. Trellis coding should always be enabled for its clear performance advantage.
BIT msanAdslLineExtnTransAturCap	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.8	Bits	read-only	The transmission modes that the ATU-R is capable of supporting. The modes available are limited by the design of the equipment.
INT msanAdslLineExtnPMConfPMSF	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.9	INTEGER	read-write	PM-related parameter used by the ATU-C to force a change in the line state.(Not available for ADSL/ADSL2Plus).
INT msanAdslLineExtnDeltConfLDSF	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.10	INTEGER	read-write	DELT-related parameter used by the ATU-C to force the line into loop diagnostics mode.(Not available for ADSL and ADSL2plus).
BIT msanAdslLineExtnTransAtucConfig	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.11	Bits	read-write	The transmission modes that the ATU-C is capable of supporting. The modes available are limited by the design of the equipment. REFERENCE Section 7.3.2 ITU G.997.1.
I32 msanAdslLineExtnAtucCurrOutputPwr	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.12	Integer32	read-only	This parameter indicates the measure of total output power transmitted by this ATU. The value of this parameter is dynamic and will also show the change in Tx power due to Power Management. For example, the value will decrease in L2 low power mode. This value can be negative
OCT msanAdslLineExtnAtucBinSNRMargin	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.13	OCTET STRING	read-only	This Conexant parameter is an array of upstream SNR Margin values in dB. Each array entry represents the SNR Margin value for particular sub carrier.
INT msanAdslLineExtnUtopiaL2RxAddrSecond	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.14	INTEGER	read-only	Conexant parameter to set UTOPIA Level 2 Rx address for the secondary bearer channel in case of Dual Latency.
INT msanAdslLineExtnUtopiaL2TxAddrSecond	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.15	INTEGER	read-only	Conexant parameter to set UTOPIA Level 2 Tx address for the secondary bearer channel in case of Dual Latency.
INT msanAdslLineExtnDsBinSnrUpdate	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.16	INTEGER	read-write	Conexant parameter to enable or disable collection of downstream SNR bin status
INT msanAdslLineExtnServiceType	1.3.6.1.4.1.1332.1.1.5.3.36.3.1.17	INTEGER	read-only	The service type configured in ADSL configuration profile which applies for this line. Supported values: 1: multimode 2: reserved 3: T1_413 4: G.DMT 6: ADSL2+ 7: ADSL2 8: ADSL2+ AUTO[+Annex M] 9: ADSL2 AUTO[+Annex M] 10: READSL2
msanAdslAturPhysExtnTable	1.3.6.1.4.1.1332.1.1.5.3.36.4		not-accessible	This table is an extention to adslAtucPhysTable defined in rfc-2662. This table provides one row for each ATUR. Each row contains the Physical Layer Parameters table for that ATUR.
msanAdslAturPhysExtnEntry	1.3.6.1.4.1.1332.1.1.5.3.36.4.1		not-accessible	An entry (conceptual row) in the msanAdslAturPhysExtnTable. The Table is indexed by ifIndex.
OCT msanAdslAturPhysExtnConfig	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.1	OCTET STRING	read-only	This object provides the upstream and downstream ATU-R configuration data, as defined in T1.413 i2, Sections 6.4, 6.6, 7.4, 7.6 and Table 27.
I32 msanAdslAturPhysExtnChanPerfCD	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.2	Integer32	read-only	The far-end delineated total cell count performance parameter is a count of the total number of cells passed through the cell delineation and HEC function process operating on the ATM Data Path while in the SYNC state.(Not available for ADSL).
I32 msanAdslAturPhysExtnChanPerfCU	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.3	Integer32	read-only	The far-end user total cell count performance parameter is a count of the total number of cells in the ATM Data Path delivered at the V-C (for ATU-C) or T-R (for ATUR) interface. (Not available for ADSL).
I32 msanAdslAturPhysExtnChanPerfBE	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.4	Integer32	read-only	The far-end idle bit error count performance parameter is a count of the number of bit errors in the idle cell payload received in the ATM Data Path at the far-end. (Not available for ADSL).
I32 msanAdslAturPhysExtnDeltHLINSCds	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.5	Integer32	read-only	DELT-related parameter that provides the scale factor to be applied to the downstream Hlin(f) values.(Not available for ADSL and ADSL2plus).
OCT msanAdslAturPhysExtnDeltHLINpsds	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.6	OCTET STRING	read-only	DELT-related parameter that provides an array of complex downstream Hlin(f) values in linear scale. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets.
I32 msanAdslAturPhysExtnDeltHLOGMTds	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.7	Integer32	read-only	DELT-related parameter that provides the number of symbols used to measure the downstream Hlog(f). (Not available for ADSL and ADSL2plus).
OCT msanAdslAturPhysExtnDeltHLOGpsus	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.8	OCTET STRING	read-only	DELT-related parameter that provides an array of real downstream Hlog(f) values in dB. (Not available for ADSL and ADSL2plus).
I32 msanAdslAturPhysExtnDeltQLNMTds	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.9	Integer32	read-only	DELT-related parameter that provides the number of symbols used to measure the downstream QLN(f) values. (Not available for ADSL and ADSL2plus).
OCT msanAdslAturPhysExtnDeltQLNpsds	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.10	OCTET STRING	read-only	DELT-related parameter that provides an array of real downstream QLN(f) values in dB. (Not available for ADSL and ADSL2plus). Every two octets refer to one element in this array of octets.
INT msanAdslAturPhysExtnDeltLastTxState	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.11	INTEGER	read-only	DELT-related parameter that provides last successful transmitted initialization state by the ATU-R. (Not available for ADSL and ADSL2plus).
G32 msanAdslAturMSGus	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.12	Gauge32	read-only	Indicates the Overhead Channel. This feature is not supported by DSLPHY as yet.
G32 msanAdslAturDeltSNRMTds	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.13	Gauge32	read-only	DELT-related parameter that provides the number of symbols used to measure the downstream SNR(f) values. (Not available for ADSL and ADSL2plus)
I32 msanAdslAturSATN	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.14	Integer32	read-only	DELT-related parameter that provides the downtream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). For further details, Refer to Section 7.5.1.9 Revised Recommendation G.997.1.
OCT msanAdslAturPhysExtnSystemVendorId	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.15	OCTET STRING	read-only	Indicates the Vendor ID as inserted by the ATU-R in the Embedded Operations Channel(ADSL). Typically identiies the ATU-R system integrator which usually refers to the vendor of the smallest field-replaceable unit. ATU-R System Vendor ID may not be the same as ATU-R G.994.1 Vendor ID. For ADSL2, provides the Vendor ID as inserted by the ATU-R in the Overhead Messages. It is not available for ADSL. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number.
OCT msanAdslAturPhysExtnGainspsDs	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.16	OCTET STRING	read-only	This parameter defines the downstream gains allocation table per bin. For further details, Refer to Section 7.5.1.21.3 Revised Recommendation G.997.1. It is supported for ADSL2/ADSl2plus only.
G32 msanAdslAturPhysExtnSelfTestResult	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.17	Gauge32	read-only	Defines the ATU-R selftest result. The most significant octet is: 00 hex if the self-test passed or 01 hex if the self-test failed. Interpretation of the other octets is vendor discretionary and can be interpreted in combination with G.994.1 and system Vendor IDs. For further details, refer to Section 7.4.10 Revised Recommendation G.997.1.
OCT msanAdslAturPhysExtnG9941VendorId	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.18	OCTET STRING	read-only	Indicates the Vendor ID as inserted by the ATU-R in the G.994.1 CLR message.The G.994.1 Vendor ID typically identifies the vendor of the ATU-R G.994.1 functionality. This is string of 8 octets containing 2 octet country code , 4 octet vendor id and 2 octet vendor revision number. For further details, refer to Section 7.4.2 Revised Recommendation G.997.1.
OCT msanAdslAturPhysExtnTsspsDs	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.19	OCTET STRING	read-only	This parameter provides the Downstream Transmit Spectrum Shaping parameter expressed as the set of break points exchanged during G994.1. Value of this parameter is in range 0 - 127, in multiples of -0.5 dB. 127 is a special value indicating the subcarrier is not transmitted. It is available only for ADSL2/ADSL2plus. For further details, Refer to Section 7.5.1.21.5 Revised Recommendation G.997.1
I32 msanAdslAturPhysExtnActPsdDs	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.20	Integer32	read-only	This parameter defines the average downstream transmit power spectrum density over the used subcarriers delivered by the ATU-C at the U-C reference point, at the instant of measurement. It's value ranges from -90 to 0, in 0.1 dB/Hz steps. It is available only for ADSL2/ADSL2plus.For further details, Refer to Section 7.5.1.14 Revised Recommendation G.997.1.
U32 msanAdslAturPhysExtnBitSwapCount	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.21	Unsigned32	read-only	This Conexant parameter indicates the bit swap count. It can read only in data mode
INT msanAdslAturPhysExtnPsdMaskMode	1.3.6.1.4.1.1332.1.1.5.3.36.4.1.22	INTEGER	read-only	This conexant parameter that indicates the actual PSD Mask currently being used by ATU-R
msanEaps	1.3.6.1.4.1.1332.1.1.5.3.37
msanEapsGlobal	1.3.6.1.4.1.1332.1.1.5.3.37.1
INT msanEapsAdminState	1.3.6.1.4.1.1332.1.1.5.3.37.1.1	INTEGER	read-write	Global EAPS administrative state.
msanEapsDomainTable	1.3.6.1.4.1.1332.1.1.5.3.37.2		not-accessible	EAPS domain configuration.
msanEapsDomainEntry	1.3.6.1.4.1.1332.1.1.5.3.37.2.1		not-accessible	Description.
OCT msanEapsDomainName	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.2	OCTET STRING	not-accessible	Description of the EAPS domain. Each msanEapsDomainName value in this table must be unique.
INT msanEapsDomainDeviceRole	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.3	INTEGER	read-write	Role of the node in the EAPS domain (Master or Transit)
INT msanEapsDomainHelloTime	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.4	INTEGER	read-write	EAPS domain hello frame send interval. This value must be lower than msanEapsDomainFailTimeout
INT msanEapsDomainFailTimeout	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.5	INTEGER	read-write	EAPS fail timeout. This value must be higher than msanEapsDomainHelloTime
INT msanEapsDomainAdminState	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.6	INTEGER	read-write	EAPS domain administrative state. State can be changed from disable to enable only when all parameters in this table are defined.
I32 msanEapsDomainPrimaryIfIndex	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.7	Integer32	read-write	EAPS primary interface. The value must be different from msanEapsSecondaryIfIndex. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. ifType of selected interface can be ethernetCsmacd(6) or ieee8023adLag (161). This parameter can be undefined when EAPS domain is created and msanEapsDomainAdminState is disable.
I32 msanEapsDomainSecondaryIfIndex	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.8	Integer32	read-write	EAPS secondary interface. The value must be different from msanEapsPrimaryIfIndex. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. ifType of selected interface can be ethernetCsmacd(6) or ieee8023adLag (161). This parameter can be undefined when EAPS domain is created and msanEapsDomainAdminState is disable.
I32 msanEapsDomainCntrlVlanId	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.9	Integer32	read-write	EAPS control VLAN ID. Selected VLAN ID must exists in dot1qVlanStaticTable. This parameter can be undefined when EAPS domain is created and msanEapsDomainAdminState is disable.
ROW msanEapsDomainRowStatus	1.3.6.1.4.1.1332.1.1.5.3.37.2.1.10	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. If msanEapsDomainAdminState is disable, created row can be actived by row status object also when next parameters are not defined: - msanEapsDomainPrimaryifIndex - msanEapsDomainSecondaryifIndex - msanEapsDomainCntrlVlanId
msanEapsDomainProtVlanTable	1.3.6.1.4.1.1332.1.1.5.3.37.3		not-accessible	List of protected VLANs for EAPS domain.
msanEapsDomainProtVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.37.3.1		not-accessible	Description.
ROW msanEapsDomainProtVlanRowStatus	1.3.6.1.4.1.1332.1.1.5.3.37.3.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanCpe	1.3.6.1.4.1.1332.1.1.5.3.38
msanCpeGlobal	1.3.6.1.4.1.1332.1.1.5.3.38.1
U32 msanCpeReset	1.3.6.1.4.1.1332.1.1.5.3.38.1.1	Unsigned32	read-write	Reset CPE equipment connected to selected interface index (ifIndex).
U32 msanCpeSendConfig	1.3.6.1.4.1.1332.1.1.5.3.38.1.2	Unsigned32	read-write	Apply configuration to CPE equipment connected to selected interface index (ifIndex).
OCT msanCpeApiMajorVersion	1.3.6.1.4.1.1332.1.1.5.3.38.1.3	OCTET STRING	read-only	CPE API major version information.
OCT msanCpeApiMinorVersion	1.3.6.1.4.1.1332.1.1.5.3.38.1.4	OCTET STRING	read-only	CPE API minor version information.
msanCpeTypeTable	1.3.6.1.4.1.1332.1.1.5.3.38.2		not-accessible	List of possible CPE types.
msanCpeTypeEntry	1.3.6.1.4.1.1332.1.1.5.3.38.2.1		not-accessible	Description.
OCT msanCpeTypeName	1.3.6.1.4.1.1332.1.1.5.3.38.2.1.1	OCTET STRING	not-accessible	Usage name of CPE model.
I32 msanCpeTypePortNum	1.3.6.1.4.1.1332.1.1.5.3.38.2.1.2	Integer32	read-write	Number of CPE user ports.
msanCpeIntfTypeTable	1.3.6.1.4.1.1332.1.1.5.3.38.3		not-accessible	Tabel defines which CPE model can be connected to selected interface.
msanCpeIntfTypeEntry	1.3.6.1.4.1.1332.1.1.5.3.38.3.1		not-accessible	Description.
ROW msanCpeIntfTypeRowStatus	1.3.6.1.4.1.1332.1.1.5.3.38.3.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
OCT msanCpeIntfTypeHwVersion	1.3.6.1.4.1.1332.1.1.5.3.38.3.1.2	OCTET STRING	read-only	Connected CPE hardware version.
OCT msanCpeIntfTypeSwVersion	1.3.6.1.4.1.1332.1.1.5.3.38.3.1.3	OCTET STRING	read-only	Connected CPE software version.
msanCpeIntfPortTable	1.3.6.1.4.1.1332.1.1.5.3.38.4		not-accessible	Table of CPE ports parameters
msanCpeIntfPortEntry	1.3.6.1.4.1.1332.1.1.5.3.38.4.1		not-accessible	Description.
INT msanCpeIntfPortId	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.1	INTEGER	not-accessible	CPE port ID (1 .. n).
INT msanCpeIntfPortPowerMode	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.2	INTEGER	read-write	Power mode of the CPE port. When port is in Sleep(2) mode, automatic wake-up is also activated.
INT msanCpeIntfPortLinkMode	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.3	INTEGER	read-write	Speed and duplex mode of the CPE port.
INT msanCpeIntfPortPvid	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.4	INTEGER	read-write	Default Vlan ID (pVID) for selected CPE port.
INT msanCpeIntfPortCos	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.5	INTEGER	read-write	Default CoS bit settings for the CPE port.
INT msanCpeIntfPortOverrideVid	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.6	INTEGER	read-write	When enable(1)VLAN ID of received tagged frame on selected CPE port is overwritten with default VLAN ID (msanCpeIntfPortPvid).
INT msanCpeIntfPortOverrideCos	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.7	INTEGER	read-write	When enable(1)CoS value of received tagged frame on selected CPE port is overwritten with default CoS bit settings (msanCpeIntfPortCos).
INT msanCpeIntfPortProtection	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.8	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)
INT msanCpeIntfPortStatus	1.3.6.1.4.1.1332.1.1.5.3.38.4.1.9	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
msanCpeTrafficTable	1.3.6.1.4.1.1332.1.1.5.3.38.5		not-accessible	Description.
msanCpeTrafficEntry	1.3.6.1.4.1.1332.1.1.5.3.38.5.1		not-accessible	Description.
I32 msanCpeTrafficId	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.1	Integer32	not-accessible	Number identifying traffic configuration (1 .. n).
OCT msanCpeTrafficName	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.2	OCTET STRING	read-write	Name identifying traffic configuration. Must be unique value.
I32 msanCpeTrafficSpeed	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.3	Integer32	read-write	Maximum bitrate of services using this traffic configuration. Domain value is 0-100000kbit/s, where: - for speeds below 1Mbit/s step is 64kbit/s - for speeds above 1Mbit/s step is 1000kbit/s
INT msanCpeTrafficFlowCntrlMode	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.4	INTEGER	read-write	Flow control mode. When enable(1) and speed is to be exceeded, device will send PAUSE flow control packet. If disable(2) packet will be just dropped.
ROW msanCpeTrafficRowStatus	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry, if msanCpeTrafficName is defined. Setting this object to destroy(6) will remove this entry.
INT msanCpeTrafficProtection	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.6	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)
INT msanCpeTrafficStatus	1.3.6.1.4.1.1332.1.1.5.3.38.5.1.7	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
msanCpeServiceTable	1.3.6.1.4.1.1332.1.1.5.3.38.6		not-accessible	Description.
msanCpeServiceEntry	1.3.6.1.4.1.1332.1.1.5.3.38.6.1		not-accessible	Description.
I32 msanCpeServiceId	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.1	Integer32	not-accessible	Number identifying service configuration (0 .. n).
OCT msanCpeServiceName	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.2	OCTET STRING	read-write	Name identifying service. Must be unique value.
I32 msanCpeServiceCVlanId	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.3	Integer32	read-write	Customer VLAN ID, used for all frames belong to this service.
I32 msanCpeServiceCCos	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.4	Integer32	read-write	CoS bit settings for all frames belonging to this service.
I32 msanCpeServiceTrafficId	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.5	Integer32	read-write	Reference to parameter msanCpeTrafficId (1 .. n), which identifies traffic configuration . Value 0 is used when traffic configuration is not defined.
OCT msanCpeServiceUntaggedPorts	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.6	OCTET STRING	read-write	The set of ports (bitmask) which should transmit egress packets as untagged. When untagged frame is received on this ports set, appropriate default VLAN ID (msanCpeIntfPortPvid) and default CoS bits (msanCpeIntfPortCos) are set.
OCT msanCpeServiceTaggedPorts	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.7	OCTET STRING	read-write	The set of ports (bitmask) where frames can be received only if they have appropriate Customer VLAN ID (msanCpeServiceCVlanId). Otherwise they are dropped. When transmitting frames to this set of ports, VLAN tags are not removed.
INT msanCpeServiceCMltcstMode	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.8	INTEGER	read-write	Mode of multicast operation for this service.
ROW msanCpeServiceRowStatus	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.9	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry, if msanCpeServiceName and msanCpeServiceTrafficId are defined. Setting this object to destroy(6) will remove this entry.
OCT msanCpeServiceTypeName	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.10	OCTET STRING	read-write	Usage name of CPE model. Must be one of predefined msanCpeTypeName values.
INT msanCpeServiceProtection	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.11	INTEGER	read-write	If protection flag is set to protected (1), other profile values cannot be edited. Protection flag is always protected (1) and it can't be changed if profile is assigned as dynamic: msanAclProfileStatus = dynamic(2)
INT msanCpeServiceStatus	1.3.6.1.4.1.1332.1.1.5.3.38.6.1.12	INTEGER	read-only	Profile status. If status is dynamic, profile values can't be edited.
msanCpeIntfServiceTable	1.3.6.1.4.1.1332.1.1.5.3.38.7		not-accessible	This table links CPE ports on selected interface with appropriate service.
msanCpeIntfServiceEntry	1.3.6.1.4.1.1332.1.1.5.3.38.7.1		not-accessible	Description.
ROW msanCpeIntfServiceRowStatus	1.3.6.1.4.1.1332.1.1.5.3.38.7.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanBoard	1.3.6.1.4.1.1332.1.1.5.3.39
msanBoardGlobal	1.3.6.1.4.1.1332.1.1.5.3.39.1
INT msanBoardReset	1.3.6.1.4.1.1332.1.1.5.3.39.1.1	INTEGER	read-write	Reset board in specified shelf slot ID (>0).
msanBoardConfTable	1.3.6.1.4.1.1332.1.1.5.3.39.2		not-accessible	Description.
msanBoardConfEntry	1.3.6.1.4.1.1332.1.1.5.3.39.2.1		not-accessible	Description.
INT msanBoardConfNr	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.1	INTEGER	not-accessible	Unique identification of a board.
INT msanBoardConfParentNr	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.2	INTEGER	read-write	Unique identification of a parent board.
INT msanBoardConfPosition	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.3	INTEGER	read-write	Position of the board on the parent board.
OCT msanBoardConfType	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.4	OCTET STRING	read-only	Type of physical board (e.g. IDC, SGO, SFA, ...). This value is automatically set according to msanBoardConfRequiredId.
OCT msanBoardConfRequiredId	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.5	OCTET STRING	read-write	Required identification of a board, which is one of available msanBoardListId values (e.g. UTA6041BA).
OCT msanBoardConfActualId	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.6	OCTET STRING	read-only	Actual identification of a board (e.g. UTA6041BA050 - last three numbers define board version).
OCT msanBoardConfSerialNr	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.7	OCTET STRING	read-only	Serial number of a board.
OCT msanBoardConfDescription	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.8	OCTET STRING	read-write	Description of the board.
INT msanBoardConfStatus	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.9	INTEGER	read-only	Physical status of configured board.
ROW msanBoardConfRowStatus	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.10	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deactivation use notInService(2). For row deletion use destroy(6) (board with management interface can not be deleted). Other values are currently not supported. For row activation next terms must be accomplished: - all requested values (they don't have default definition) must be set - msanBoardConfId is one of available msanBoardListId values
OCT msanBoardConfSwSteerVersion	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.11	OCTET STRING	read-only	The unique steer code of installed software.
OCT msanBoardConfSwBuildDirectory	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.12	OCTET STRING	read-only	The directory where installed software was build on.
OCT msanBoardConfSwBuildTime	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.13	OCTET STRING	read-only	The time when the installed software was built. (DateAndTime textual convention, from SNMPv2-TC)
OCT msanBoardConfSwBranch	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.14	OCTET STRING	read-only	The repository branch where the installed software was built from.
OCT msanBoardConfSwBuildReference	1.3.6.1.4.1.1332.1.1.5.3.39.2.1.15	OCTET STRING	read-only	The repository reference number of the installed software build branch.
msanBoardListTable	1.3.6.1.4.1.1332.1.1.5.3.39.3		not-accessible	Description.
msanBoardListEntry	1.3.6.1.4.1.1332.1.1.5.3.39.3.1		not-accessible	Description.
OCT msanBoardListId	1.3.6.1.4.1.1332.1.1.5.3.39.3.1.1	OCTET STRING	read-only	Identification of supported board (e.g. UTA6041BA).
OCT msanBoardListType	1.3.6.1.4.1.1332.1.1.5.3.39.3.1.2	OCTET STRING	read-only	Type of physical board (e.g. IDC, SGO, SFA, ...).
msanFtpServer	1.3.6.1.4.1.1332.1.1.5.3.40
msanFtpServerGlobal	1.3.6.1.4.1.1332.1.1.5.3.40.1
INT msanFtpServerAdminState	1.3.6.1.4.1.1332.1.1.5.3.40.1.1	INTEGER	read-write	FTP server administrative state.
msanAppRateLimit	1.3.6.1.4.1.1332.1.1.5.3.41
msanAppRateLimitGlobal	1.3.6.1.4.1.1332.1.1.5.3.41.1
msanAppRateLimitTable	1.3.6.1.4.1.1332.1.1.5.3.41.2		not-accessible	Description.
msanAppRateLimitEntry	1.3.6.1.4.1.1332.1.1.5.3.41.2.1		not-accessible	Description.
I32 msanAppRateLimitDhcp	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.1	Integer32	read-write	Maximum number of received DHCP packets in one second (pps) per interface. Value 0 defines there is no limit.
INT msanAppRateLimitDhcpState	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.2	INTEGER	read-write	Administrative state of DHCP traffic rate limiting.
I32 msanAppRateLimitPppoe	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.3	Integer32	read-write	Maximum number of received PPPoE packets in one second (pps) per interface. Value 0 defines there is no limit.
INT msanAppRateLimitPppoeState	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.4	INTEGER	read-write	Administrative state of PPPoE traffic rate limiting.
I32 msanAppRateLimitIgmp	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.5	Integer32	read-write	Maximum number of received DHCP packets in one second (pps) per interface. Value 0 defines there is no limit.
INT msanAppRateLimitIgmpState	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.6	INTEGER	read-write	Administrative state of IGMP traffic rate limiting.
I32 msanAppRateLimitStp	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.7	Integer32	read-write	Maximum number of received STP packets in one second (pps) per interface. Value 0 defines there is no limit.
INT msanAppRateLimitStpState	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.8	INTEGER	read-write	Administrative state of STP traffic rate limiting.
I32 msanAppRateLimitMn	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.9	Integer32	read-write	Maximum number of received MN packets (management traffic) in one second (pps) per interface. Value 0 defines there is no limit.
INT msanAppRateLimitMnState	1.3.6.1.4.1.1332.1.1.5.3.41.2.1.10	INTEGER	read-write	Administrative state of MN traffic rate limiting.
msanMlinec	1.3.6.1.4.1.1332.1.1.5.3.50
msanMlinecGlobal	1.3.6.1.4.1.1332.1.1.5.3.50.1
INT msanMlinecAdminState	1.3.6.1.4.1.1332.1.1.5.3.50.1.1	INTEGER	read-write	MLINEC (Multi-Link Network Connectivity) administrative state.
msanMulticast	1.3.6.1.4.1.1332.1.1.5.3.100
msanMulticastGlobal	1.3.6.1.4.1.1332.1.1.5.3.100.1
msanMulticastIntfStaticGroupTable	1.3.6.1.4.1.1332.1.1.5.3.100.2		not-accessible	The table attaches static multicast groups to the interfaces.
msanMulticastIntfStaticGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.100.2.1		not-accessible	Description.
IP msanMulticastIntfStaticGroupIPAddr	1.3.6.1.4.1.1332.1.1.5.3.100.2.1.1	IpAddress	not-accessible	IP multicast address of valid multicast group.
ROW msanMulticastIntfStaticGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.2.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastGroupTable	1.3.6.1.4.1.1332.1.1.5.3.100.3		not-accessible	Description.
msanMulticastGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.100.3.1		not-accessible	Description.
IP msanMulticastGroupIpAddr	1.3.6.1.4.1.1332.1.1.5.3.100.3.1.1	IpAddress	not-accessible	IP multicast address of valid multicast group.
OCT msanMulticastGroupName	1.3.6.1.4.1.1332.1.1.5.3.100.3.1.2	OCTET STRING	read-write	Name of multicast group.
ROW msanMulticastGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.3.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported].
msanMulticastAclListTable	1.3.6.1.4.1.1332.1.1.5.3.100.4		not-accessible	The table below assigns the symbolic names to the specific multicast ACLs.
msanMulticastAclListEntry	1.3.6.1.4.1.1332.1.1.5.3.100.4.1		not-accessible	Description.
INT msanMulticastAclListId	1.3.6.1.4.1.1332.1.1.5.3.100.4.1.1	INTEGER	not-accessible	Multicast List id. Integer from 0 to 255.
STR msanMulticastAclListName	1.3.6.1.4.1.1332.1.1.5.3.100.4.1.2	SnmpAdminString	read-write	ACL list symbolic name. Should be unique.
ROW msanMulticastAclListRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.4.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanMulticastAclListGroupTable	1.3.6.1.4.1.1332.1.1.5.3.100.5		not-accessible	The table below links the multicast groups to the ACL.
msanMulticastAclListGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.100.5.1		not-accessible	Description.
IP msanMulticastAclGroupIpAddr	1.3.6.1.4.1.1332.1.1.5.3.100.5.1.1	IpAddress	not-accessible	IP multicast address of valid ACL multicast group.
ROW msanMulticastAclListGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.5.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastAclIntfListTable	1.3.6.1.4.1.1332.1.1.5.3.100.6		not-accessible	The table below assigns the multicast ACL to the interfaces
msanMulticastAclIntfListEntry	1.3.6.1.4.1.1332.1.1.5.3.100.6.1		not-accessible	Description.
INT msanMulticastAclIntfListMode	1.3.6.1.4.1.1332.1.1.5.3.100.6.1.1	INTEGER	read-write	Defines the mode in which interface for specified ACL list works.
ROW msanMulticastAclIntfListRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.6.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanMulticastAclListVlanGroupTable	1.3.6.1.4.1.1332.1.1.5.3.100.7		not-accessible	The table below links the multicast groups to the ACL.
msanMulticastAclListVlanGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.100.7.1		not-accessible	Description.
IP msanMulticastAclListVlanGroupIpAddr	1.3.6.1.4.1.1332.1.1.5.3.100.7.1.1	IpAddress	not-accessible	IP multicast address of valid ACL multicast group.
ROW msanMulticastAclListVlanGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.7.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastIntfVlanStaticGroupTable	1.3.6.1.4.1.1332.1.1.5.3.100.8		not-accessible	Description.
msanMulticastIntfVlanStaticGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.100.8.1		not-accessible	Description.
IP msanMulticastIntfVlanStaticGroupIpAddr	1.3.6.1.4.1.1332.1.1.5.3.100.8.1.1	IpAddress	not-accessible	IP multicast address of valid multicast group.
ROW msanMulticastIntfVlanStaticGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.8.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastAccessListTable	1.3.6.1.4.1.1332.1.1.5.3.100.9		not-accessible	The table below assigns the symbolic names to the specific multicast ACLs.
msanMulticastAccessListEntry	1.3.6.1.4.1.1332.1.1.5.3.100.9.1		not-accessible	Description.
OCT msanMulticastAccessListName	1.3.6.1.4.1.1332.1.1.5.3.100.9.1.1	OCTET STRING	not-accessible	ACL list symbolic name. Should be unique.
ROW msanMulticastAccessListRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.9.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndGo(4). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanMulticastAccessListGroupTable	1.3.6.1.4.1.1332.1.1.5.3.100.10		not-accessible	The table below links the multicast addresses to the ACL list
msanMulticastAccessListGroupEntry	1.3.6.1.4.1.1332.1.1.5.3.100.10.1		not-accessible	Description.
IP msanMulticastAccessListGroupIpAddr	1.3.6.1.4.1.1332.1.1.5.3.100.10.1.1	IpAddress	not-accessible	IP multicast address of valid ACL multicast group.
ROW msanMulticastAccessListGroupRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.10.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanMulticastAccessListIntfTable	1.3.6.1.4.1.1332.1.1.5.3.100.11		not-accessible	The table below assigns the multicast ACL list to the interfaces
msanMulticastAccessListIntfEntry	1.3.6.1.4.1.1332.1.1.5.3.100.11.1		not-accessible	Description.
INT msanMulticastAccessListIntfMode	1.3.6.1.4.1.1332.1.1.5.3.100.11.1.1	INTEGER	read-write	Defines the mode in which interface for specified ACL list works.
ROW msanMulticastAccessListIntfRowStatus	1.3.6.1.4.1.1332.1.1.5.3.100.11.1.2	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanSwitchMFDBTable	1.3.6.1.4.1.1332.1.1.5.3.100.12		not-accessible	The Multicast Forwarding Database table
msanSwitchMFDBEntry	1.3.6.1.4.1.1332.1.1.5.3.100.12.1		not-accessible	Contains Forwarding and Filtering information per Component User, Vlan Index, and MAC Address.
INT msanSwitchMFDBProtocolType	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.1	INTEGER	read-only	The component that is responsible for this entry in the Multicast Forwarding Database.
VLA msanSwitchMFDBVlanId	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.2	VlanIndex	read-only	Vlan Index for which this entry is associated with.
MAC msanSwitchMFDBMacAddress	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.3	MacAddress	read-only	A multicast MAC address for which the switch has forwarding and or filtering information.
INT msanSwitchMFDBType	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.4	INTEGER	read-only	This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol
STR msanSwitchMFDBDescription	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.5	DisplayString	read-only	Text description of this multicast table entry.
POR msanSwitchMFDBForwardingPortMask	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.6	PortMask	read-only	BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
POR msanSwitchMFDBFilteringPortMask	1.3.6.1.4.1.1332.1.1.5.3.100.12.1.7	PortMask	read-only	BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.
msanFiltering	1.3.6.1.4.1.1332.1.1.5.3.101
msanFilteringGlobal	1.3.6.1.4.1.1332.1.1.5.3.101.2
msanFilteringFilterTable	1.3.6.1.4.1.1332.1.1.5.3.101.3		not-accessible	Defines a list of filters.
msanFilteringFilterEntry	1.3.6.1.4.1.1332.1.1.5.3.101.3.1		not-accessible	Description.
I32 msanFilteringFilterId	1.3.6.1.4.1.1332.1.1.5.3.101.3.1.1	Integer32	read-write	Filter identity.
OCT msanFilteringFilterName	1.3.6.1.4.1.1332.1.1.5.3.101.3.1.2	OCTET STRING	read-write	Name of filter to be shown.
INT msanFilteringFilterType	1.3.6.1.4.1.1332.1.1.5.3.101.3.1.3	INTEGER	read-only	Type of filter (static or dynamic).
ROW msanFilteringFilterRowStatus	1.3.6.1.4.1.1332.1.1.5.3.101.3.1.4	RowStatus	read-create	SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry.
msanFilteringAssignFilterTable	1.3.6.1.4.1.1332.1.1.5.3.101.4		not-accessible	This table defines a list of filters assigned to interface.
msanFilteringAssignFilterEntry	1.3.6.1.4.1.1332.1.1.5.3.101.4.1		not-accessible	Description.
I32 msanFilteringAssignFilterVid	1.3.6.1.4.1.1332.1.1.5.3.101.4.1.1	Integer32	read-write	ID of VLAN to be filtered.
I32 msanFilteringAssignFilterCos	1.3.6.1.4.1.1332.1.1.5.3.101.4.1.2	Integer32	read-write	CoS value to be filtered.
I32 msanFilteringAssignFilterDscp	1.3.6.1.4.1.1332.1.1.5.3.101.4.1.3	Integer32	read-write	DSCP field.
I32 msanFilteringAssignFilterPrec	1.3.6.1.4.1.1332.1.1.5.3.101.4.1.4	Integer32	read-write	Precedence in DSCP tag.
ROW msanFilteringAssignFilterRowStatus	1.3.6.1.4.1.1332.1.1.5.3.101.4.1.5	RowStatus	read-create	SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry.
msanFilteringRuleTable	1.3.6.1.4.1.1332.1.1.5.3.101.5		not-accessible	This table defines a list of filtering rules associated to filters.
msanFilteringRuleEntry	1.3.6.1.4.1.1332.1.1.5.3.101.5.1		not-accessible	Description.
I32 msanFilteringRuleId	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.1	Integer32	read-only	Filtering rule identity.
INT msanFilteringRuleResponse	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.2	INTEGER	read-write	Filter response.
MAC msanFilteringRuleFromMac	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.3	MacAddress	read-write	Source Ethernet address.
MAC msanFilteringRuleFromMacMask	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.4	MacAddress	read-write	Source Ethernet address mask.
IP msanFilteringRuleFromIp	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.5	IpAddress	read-write	Source IP address.
IP msanFilteringRuleFromMask	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.6	IpAddress	read-write	Source IP address mask.
U32 msanFilteringRuleFromPortLow	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.7	Unsigned32	read-write	The lowest number of a source TCP or UDP port.
U32 msanFilteringRuleFromPortHigh	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.8	Unsigned32	read-write	The highest number of a source TCP or UDP port..
MAC msanFilteringRuleToMac	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.9	MacAddress	read-write	Destination Ethernet address.
MAC msanFilteringRuleToMacMask	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.10	MacAddress	read-write	Destination Ethernet address mask.
IP msanFilteringRuleToIp	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.11	IpAddress	read-write	Destination IP address.
IP msanFilteringRuleToMask	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.12	IpAddress	read-write	Destination IP address mask.
U32 msanFilteringRuleToPortLow	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.13	Unsigned32	read-write	The lowest number of a destination TCP or UDP port.
U32 msanFilteringRuleToPortHigh	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.14	Unsigned32	read-write	The highest number of a destination TCP or UDP port.
OCT msanFilteringRuleEtherProto	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.15	OCTET STRING	read-write	Ethernet protocol to be filtered.
OCT msanFilteringRuleIpProto	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.16	OCTET STRING	read-write	IP protocol to be filtered.
U32 msanFilteringRuleIcmType	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.17	Unsigned32	read-write	ICMP type. ICMP sends an error message to the transmitter of IP packets and provides information at IP packet processing.
U32 msanFilteringRulePrec	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.18	Unsigned32	read-write	Precedence in DSCP tag.
U32 msanFilteringRuleTos	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.19	Unsigned32	read-write	TOS to be filtered.
U32 msanFilteringRuleVid	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.20	Unsigned32	read-write	ID of VLAN to be filtered.
U32 msanFilteringRuleCos	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.21	Unsigned32	read-write	CoS value to be filtered.
INT msanFilteringRuleTag	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.22	INTEGER	read-write	802.1Q tag.
ROW msanFilteringRuleRowStatus	1.3.6.1.4.1.1332.1.1.5.3.101.5.1.23	RowStatus	read-create	SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry.
msanFilteringAttachedFilterTable	1.3.6.1.4.1.1332.1.1.5.3.101.6		not-accessible	This table defines information about filters attached to interface.
msanFilteringAttachedFilterEntry	1.3.6.1.4.1.1332.1.1.5.3.101.6.1		not-accessible	Description.
INT msanFilteringAttachedFilterDirect	1.3.6.1.4.1.1332.1.1.5.3.101.6.1.1	INTEGER	read-write	Point of attaching a filter.
ROW msanFilteringAttachedFilterRowStatus	1.3.6.1.4.1.1332.1.1.5.3.101.6.1.2	RowStatus	read-create	SNMP row status. Supported values: active(1) - valid entry; createAndGo(4) - used to create a new entry; destroy(6) - removes the entry.
msanBridge	1.3.6.1.4.1.1332.1.1.5.3.102
msanBridgeGlobal	1.3.6.1.4.1.1332.1.1.5.3.102.1
INT msanBridgeMode	1.3.6.1.4.1.1332.1.1.5.3.102.1.1	INTEGER	read-write	A bridge operating mode. bridge(1) ccx(2)
INT msanBridgeMacTableSize	1.3.6.1.4.1.1332.1.1.5.3.102.1.2	INTEGER	read-write	The maximum MAC table size
INT msanBridgeRedAdminMode	1.3.6.1.4.1.1332.1.1.5.3.102.1.3	INTEGER	read-write	Enable or disable Random Early Discard functionality.
msanBridgeCCXTable	1.3.6.1.4.1.1332.1.1.5.3.102.2		not-accessible	The table contents the information about all CCX pairs.
msanBridgeCCXEntry	1.3.6.1.4.1.1332.1.1.5.3.102.2.1		not-accessible	Description.
NUM msanBridgeCCXInterface1	1.3.6.1.4.1.1332.1.1.5.3.102.2.1.1	InterfaceIndex	read-create	The first interface to make cross-connection exchange
NUM msanBridgeCCXInterface2	1.3.6.1.4.1.1332.1.1.5.3.102.2.1.2	InterfaceIndex	read-create	The second interface to make cross-connection exchange
ROW msanBridgeCCXRowStatus	1.3.6.1.4.1.1332.1.1.5.3.102.2.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanIPSG	1.3.6.1.4.1.1332.1.1.5.3.103
msanIPSGGlobal	1.3.6.1.4.1.1332.1.1.5.3.103.1
INT msanIPSGAdminMode	1.3.6.1.4.1.1332.1.1.5.3.103.1.1	INTEGER	read-write	Enable/disable IPv4 source guard for all interfaces
INT msanIPSGStoreAdminMode	1.3.6.1.4.1.1332.1.1.5.3.103.1.2	INTEGER	read-write	Enable/disable storing of the IP-MAC binds to the interoperation table.
INT msanIPSGIpv6AdminMode	1.3.6.1.4.1.1332.1.1.5.3.103.1.3	INTEGER	read-write	Enable/disable IPv6 source guard for all interfaces
INT msanIPSGClearDynamicBinds	1.3.6.1.4.1.1332.1.1.5.3.103.1.4	INTEGER	read-write	Clear IPSG snooping tables for all ports.
msanIPSGIntfTable	1.3.6.1.4.1.1332.1.1.5.3.103.2		not-accessible	Description.
msanIPSGIntfEntry	1.3.6.1.4.1.1332.1.1.5.3.103.2.1		not-accessible	Description.
INT msanIPSGIntfAdminMode	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.1	INTEGER	read-write	Enable/disable IP Source Guard for the selected interface.
I32 msanIPSGIntfBindsLimit	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.2	Integer32	read-write	IPSG binding limit for DHCPv4 snooping table per interface. Value 0 defines there is no limit.
INT msanIPSGIntfFilteringMode	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.3	INTEGER	read-write	Sets the traffic filtering type. Traffic can be filtered either by IP or by both IP and MAC address.
INT msanIPSGIntfIpv6AdminMode	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.4	INTEGER	read-write	Enable/disable IPv6 Source Guard for the selected interface.
I32 msanIPSGIntfBindsLimitDhcpv6	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.5	Integer32	read-write	IPSG binding limit for DHCPv6 (IPv6 DHCP)snooping table per interface. Value 0 defines there is no limit.
I32 msanIPSGIntfBindsLimitND	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.6	Integer32	read-write	IPSG binding limit for ND (IPv6 Neighbor Discovery) snooping table per interface Value 0 defines there is no limit.
INT msanIPSGIntfClearDynamicBinds	1.3.6.1.4.1.1332.1.1.5.3.103.2.1.7	INTEGER	read-write	Clear IPSG snooping tables per interface
msanIPSGBindingsTable	1.3.6.1.4.1.1332.1.1.5.3.103.3		not-accessible	DThe table for storing IP source binding
msanIPSGBindingsEntry	1.3.6.1.4.1.1332.1.1.5.3.103.3.1		not-accessible	Description.
IP msanIPSGBindIp	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.1	IpAddress	read-write	Allowed IP address
VLA msanIPSGBindVlan	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.2	VlanIndex	read-only	Allowed VLAN number
MAC msanIPSGBindMac	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.3	MacAddress	read-only	Allowed MAC address
TIK msanIPSGBindLeaseRemainingTime	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.4	TimeTicks	read-only	The period for which the DHCP lease is valid. It is displayed in days, hours, minutes, and seconds. For static IPSG bindings this value is set to 0 (infinitive).
INT msanIPSGBindType	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.5	INTEGER	read-only	Type of IPSG binding.
C32 msanIPSGBindMatchedFrames	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.6	Counter32	read-only	Number of matched frames for selected IPSG binding.
ROW msanIPSGBindRowStatus	1.3.6.1.4.1.1332.1.1.5.3.103.3.1.7	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation next terms must be accomplished: - msanIPSGBindIp must be defined
msanIPSGIpv4PortStaticBindTable	1.3.6.1.4.1.1332.1.1.5.3.103.4		not-accessible	Description.
msanIPSGIpv4PortStaticBindEntry	1.3.6.1.4.1.1332.1.1.5.3.103.4.1		not-accessible	Description.
MAC msanIPSGIpv4PortStaticBindMacAddress	1.3.6.1.4.1.1332.1.1.5.3.103.4.1.1	MacAddress	not-accessible	Allowed MAC address
VLA msanIPSGIpv4PortStaticBindVlanId	1.3.6.1.4.1.1332.1.1.5.3.103.4.1.2	VlanIndex	not-accessible	Allowed VLAN number
ADR msanIPSGIpv4PortStaticBindIpAddress	1.3.6.1.4.1.1332.1.1.5.3.103.4.1.3	InetAddressIPv4	not-accessible	Allowed IPv4 address
C32 msanIPSGIpv4PortStaticBindMatchedFrames	1.3.6.1.4.1.1332.1.1.5.3.103.4.1.4	Counter32	read-only	Number of matched frames for selected IPSG binding.
ROW msanIPSGIpv4PortStaticBindRowStatus	1.3.6.1.4.1.1332.1.1.5.3.103.4.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndGo(4). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanIPSGIpv6PortStaticBindTable	1.3.6.1.4.1.1332.1.1.5.3.103.5		not-accessible	Description.
msanIPSGIpv6PortStaticBindEntry	1.3.6.1.4.1.1332.1.1.5.3.103.5.1		not-accessible	Description.
MAC msanIPSGIpv6PortStaticBindMacAddress	1.3.6.1.4.1.1332.1.1.5.3.103.5.1.1	MacAddress	not-accessible	Allowed MAC address
VLA msanIPSGIpv6PortStaticBindVlanId	1.3.6.1.4.1.1332.1.1.5.3.103.5.1.2	VlanIndex	not-accessible	Allowed VLAN number
ADR msanIPSGIpv6PortStaticBindIpAddress	1.3.6.1.4.1.1332.1.1.5.3.103.5.1.3	InetAddressIPv6	not-accessible	Allowed IPv6 address
C32 msanIPSGIpv6PortStaticBindMatchedFrames	1.3.6.1.4.1.1332.1.1.5.3.103.5.1.4	Counter32	read-only	Number of matched frames for selected IPSG binding.
ROW msanIPSGIpv6PortStaticBindRowStatus	1.3.6.1.4.1.1332.1.1.5.3.103.5.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndGo(4). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported.
msanIPSGPortBindCurrentTable	1.3.6.1.4.1.1332.1.1.5.3.103.6		not-accessible	DThe table for storing IP source binding
msanIPSGPortBindCurrentEntry	1.3.6.1.4.1.1332.1.1.5.3.103.6.1		not-accessible	Description.
I32 msanIPSGPortBindCurrentId	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.1	Integer32	not-accessible	Table index.
NUM msanIPSGPortBindCurrentIfIndex	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.2	InterfaceIndex	read-only	Port index (ifIndex value).
MAC msanIPSGPortBindCurrentMacAddress	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.3	MacAddress	read-only	Allowed MAC address
VLA msanIPSGPortBindCurrentVlanId	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.4	VlanIndex	read-only	Allowed VLAN number
IPt msanIPSGPortBindCurrentIpAddressType	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.5	InetAddressType	read-only	Specifies the type of ip address: ipv4[1], ipv6[2].
IP msanIPSGPortBindCurrentIpAddress	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.6	InetAddress	read-only	Allowed IP address
TIK msanIPSGPortBindCurrentLeaseRemainingTime	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.7	TimeTicks	read-only	The period for which the DHCP lease is valid. It is displayed in days, hours, minutes, and seconds. For static IPSG bindings this value is set to 0 (infinitive).
INT msanIPSGPortBindCurrentType	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.8	INTEGER	read-only	Type of IPSG binding.
C32 msanIPSGPortBindCurrentMatchedFrames	1.3.6.1.4.1.1332.1.1.5.3.103.6.1.9	Counter32	read-only	Number of matched frames for selected IPSG binding.
msanVlan	1.3.6.1.4.1.1332.1.1.5.3.105
msanVlanGlobal	1.3.6.1.4.1.1332.1.1.5.3.105.1
INT msanDVlanTagMode	1.3.6.1.4.1.1332.1.1.5.3.105.1.1	INTEGER	read-write	Controls the Double Vlan Tag mode on the system.
INT msanVlanRemarkAdminState	1.3.6.1.4.1.1332.1.1.5.3.105.1.2	INTEGER	read-write	Global VLAN Remarking administrative state.
I32 msanInternalVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.1.3	Integer32	read-write	Internal Vlan ID.
msanPortVlanTable	1.3.6.1.4.1.1332.1.1.5.3.105.2		not-accessible	Vlan config parameters per port.
msanPortVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.105.2.1		not-accessible	Description.
INT msanPortVlanMode	1.3.6.1.4.1.1332.1.1.5.3.105.2.1.1	INTEGER	read-write	Interface vlan mode.
INT msanPortVlanStackPriority	1.3.6.1.4.1.1332.1.1.5.3.105.2.1.2	INTEGER	read-write	Priority of inner tag when interface is in vlanStacking mode (msanPortVlanMode=vlanStacking).
I32 msanPortVlanStackVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.2.1.3	Integer32	read-write	Vlan ID of inner tag when interface is in vlanStacking mode (msanPortVlanMode=vlanStacking).
msanPortDVlanMapTable	1.3.6.1.4.1.1332.1.1.5.3.105.3		not-accessible	Ingress mapping of inner VID to outer VID different from default (PVID) mapping.
msanPortDVlanMapEntry	1.3.6.1.4.1.1332.1.1.5.3.105.3.1		not-accessible	Description.
I32 msanPortDVlanMapInTagVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.3.1.1	Integer32	not-accessible	Inner tag VLAN ID. DVlan functionality is used when interface is in dot1qtunnel mode.
I32 msanPortDVlanMapOutTagVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.3.1.2	Integer32	read-create	Outer tag VLAN ID added for inner tag VLAN ID (msanPortDVlanMapInTagVlanId). DVlan functionality is used when interface is in dot1qtunnel mode. Value of -1 indicates that outer tag is not added for selected inner tag VLAN ID.
ROW msanPortDVlanMapRowStatus	1.3.6.1.4.1.1332.1.1.5.3.105.3.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry. Setting this object to destroy(6) will remove this entry.
msanPortVlanRemarkTable	1.3.6.1.4.1.1332.1.1.5.3.105.4		not-accessible	Vlan remarking table for ingress traffic (per port). Note: All defined Vlan remarking rules for ingress traffic also add , automatically, reverse Vlan remarking rule for egress traffic on same port.
msanPortVlanRemarkEntry	1.3.6.1.4.1.1332.1.1.5.3.105.4.1		not-accessible	Description.
I32 msanPortVlanRemarkSrcVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.4.1.1	Integer32	read-write	Ingress traffic Source VLAN ID which will be changed to Destination VLAN ID (msanPortVlanRemarkDstVlanId) by VLAN remarking rule.
I32 msanPortVlanRemarkDstVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.4.1.2	Integer32	read-write	Destination VLAN ID to which will be changed Source VLAN ID of ingress traffic (msanPortVlanRemarkSrcVlanId) by VLAN remarking rule.
ROW msanPortVlanRemarkRowStatus	1.3.6.1.4.1.1332.1.1.5.3.105.4.1.3	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation next terms must be accomplished: - msanPortVlanRemarkDstVlanId must be defined (default value not defined) Note: All defined Vlan remarking rules for ingress traffic also add , automatically, reverse Vlan remarking rule for egress traffic on same port.
msanPortDVlanTable	1.3.6.1.4.1.1332.1.1.5.3.105.5		not-accessible	Description.
msanPortDVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.105.5.1		not-accessible	Description.
INT msanPortDVlanTagMode	1.3.6.1.4.1.1332.1.1.5.3.105.5.1.1	INTEGER	read-write	Administrative state of 802.1Q tunneling (DVLAN) mode.
I32 msanPortDVlanStackVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.5.1.2	Integer32	read-write	Vlan ID of inner tag when interface is in vlanStacking mode. Interface is in vlanStacking mode when msanPortDVlanTagMode=enable and msanPortDVlanStackVlanId>=0. msanPortDVlanStackVlanId value of -1 indicates that vlanStacking mode is not activated.
INT msanPortDVlanStackPriority	1.3.6.1.4.1.1332.1.1.5.3.105.5.1.3	INTEGER	read-write	Priority of inner tag when interface is in vlanStacking mode. Interface is in vlanStacking mode when msanPortDVlanTagMode=enable and msanPortDVlanStackVlanId>=0.
msanPortDVlanConfigTable	1.3.6.1.4.1.1332.1.1.5.3.105.6		not-accessible	Ingress mapping of inner VID to outer VID different from default (PVID) mapping.
msanPortDVlanConfigEntry	1.3.6.1.4.1.1332.1.1.5.3.105.6.1		not-accessible	Description.
I32 msanDVlanConfigInTagVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.6.1.1	Integer32	not-accessible	Inner tag VLAN ID. DVlan functionality is used when interface is in dot1qtunnel mode.
INT msanDVlanConfigInTagPriority	1.3.6.1.4.1.1332.1.1.5.3.105.6.1.2	INTEGER	not-accessible	Priority of inner tag. Value unspecified(8) defines that rule line applies to all packets with appropriate msanDVlanConfigInTagVlanId, except if packet match to other more specific rule.
I32 msanDVlanConfigOutTagVlanId	1.3.6.1.4.1.1332.1.1.5.3.105.6.1.3	Integer32	read-create	Outer tag VLAN ID added for inner tag VLAN ID (msanPortDVlanConfigInTagVlanId). DVlan functionality is used when interface is in dot1qtunnel mode. Value of -1 indicates that outer tag is not added for selected inner tag VLAN ID.
INT msanDVlanConfigOutTagPriority	1.3.6.1.4.1.1332.1.1.5.3.105.6.1.4	INTEGER	read-write	Priority of outer tag. Value unspecified(8) defines that msanDVlanMapInTagPriority is copied to outer tag.
ROW msanDVlanConfigRowStatus	1.3.6.1.4.1.1332.1.1.5.3.105.6.1.5	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry. Setting this object to destroy(6) will remove this entry.
msanPortVlanRemarkAdminTable	1.3.6.1.4.1.1332.1.1.5.3.105.7		not-accessible	Description.
msanPortVlanRemarkAdminEntry	1.3.6.1.4.1.1332.1.1.5.3.105.7.1		not-accessible	Description.
INT msanPortVlanRemarkAdminMode	1.3.6.1.4.1.1332.1.1.5.3.105.7.1.1	INTEGER	read-write	Administrative mode for VLAN Remarking
msanAtm	1.3.6.1.4.1.1332.1.1.5.3.106
msanAtmGlobal	1.3.6.1.4.1.1332.1.1.5.3.106.1
msanPortAtmPvcTable	1.3.6.1.4.1.1332.1.1.5.3.106.2		not-accessible	Description.
msanPortAtmPvcEntry	1.3.6.1.4.1.1332.1.1.5.3.106.2.1		not-accessible	Description.
I32 msanPortAtmPvcVpi	1.3.6.1.4.1.1332.1.1.5.3.106.2.1.1	Integer32	not-accessible	ATM-PVC(Permanent Virtual Circuits) VPI(Virtual Path Identifier) value.
I32 msanPortAtmPvcVci	1.3.6.1.4.1.1332.1.1.5.3.106.2.1.2	Integer32	not-accessible	ATM-PVC(Permanent Virtual Circuits) VCI(Virtual Channel Identifier) value.
INT msanPortAtmPvcPvid	1.3.6.1.4.1.1332.1.1.5.3.106.2.1.3	INTEGER	read-write	The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this ATM-PVC(Permanent Virtual Circuits). Value 0 defines that PVID is not set.
ROW msanPortAtmPvcRowStatus	1.3.6.1.4.1.1332.1.1.5.3.106.2.1.4	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. For row creation use createAndWait(5) [createAndGo(4) is not supported]. Setting this object to active(1) will activate this entry. Setting this object to destroy(6) will remove this entry.
msanEnergyMeter	1.3.6.1.4.1.1332.1.1.5.3.107
msanEnergyMeterGlobal	1.3.6.1.4.1.1332.1.1.5.3.107.1
IP msanEnergyMeterIpAddress	1.3.6.1.4.1.1332.1.1.5.3.107.1.1	IpAddress	read-write	Energy meter's Ip address.
U32 msanEnergyMeterTcpPort	1.3.6.1.4.1.1332.1.1.5.3.107.1.2	Unsigned32	read-write	Energy meter's Tcp port.
U32 msanEnergyMeterAddress	1.3.6.1.4.1.1332.1.1.5.3.107.1.3	Unsigned32	read-write	Energy meter's address.
U32 msanEnergyMeterPassword	1.3.6.1.4.1.1332.1.1.5.3.107.1.4	Unsigned32	read-write	Energy meter's password.
OCT msanEnergyMeterSerialNo	1.3.6.1.4.1.1332.1.1.5.3.107.1.5	OCTET STRING	read-only	Energy meter's serial number.
OCT msanEnergyMeterDateTime	1.3.6.1.4.1.1332.1.1.5.3.107.1.6	OCTET STRING	read-only	Energy meter's date and time in format: year-month-day, hour:minutes:seconds
U32 msanEnergyMeterCurrTariff	1.3.6.1.4.1.1332.1.1.5.3.107.1.7	Unsigned32	read-only	Energy meter's current active tariff.
U32 msanEnergyMeterCurrPower	1.3.6.1.4.1.1332.1.1.5.3.107.1.8	Unsigned32	read-only	Energy meter's current measured power.
U32 msanEnergyMeterCoreVersion	1.3.6.1.4.1.1332.1.1.5.3.107.1.9	Unsigned32	read-only	Energy meter's current version number.
U32 msanEnergyMeterFwType	1.3.6.1.4.1.1332.1.1.5.3.107.1.10	Unsigned32	read-only	Energy meter's current firmware type.
U32 msanEnergyMeterFwVersion	1.3.6.1.4.1.1332.1.1.5.3.107.1.11	Unsigned32	read-only	Energy meter's current firmware version.
OCT msanEnergyMeterFwCreationDate	1.3.6.1.4.1.1332.1.1.5.3.107.1.12	OCTET STRING	read-only	Energy meter's current firmware creation date in format: year-month-day
msanEnergyMeterEnergyTable	1.3.6.1.4.1.1332.1.1.5.3.107.2		not-accessible	Energy values.
msanEnergyMeterEnergyEntry	1.3.6.1.4.1.1332.1.1.5.3.107.2.1		not-accessible	Description.
U32 msanEnergyMeterTariff	1.3.6.1.4.1.1332.1.1.5.3.107.2.1.1	Unsigned32	not-accessible	This is msanEnergyMeterTariff index in msanEnergyMeterEnergyTable Defines tariff. 0 tariff No1, 1 tariff No2, , 7 - tariff No8
U32 msanEnergyMeterDepth	1.3.6.1.4.1.1332.1.1.5.3.107.2.1.2	Unsigned32	not-accessible	This is msanEnergyMeterDepth index in msanEnergyMeterEnergyTable. Defines time span. 0 current value, 1 value at the end of previous month, 2 value at the end of 2. month ago, , 13 value at the end of the 13. month ago
U32 msanEnergyMeterEnergyValue	1.3.6.1.4.1.1332.1.1.5.3.107.2.1.3	Unsigned32	read-only	Energy value.
msanEnergyMeterEnergySumTable	1.3.6.1.4.1.1332.1.1.5.3.107.3		not-accessible	Energy sum values of all tariffs.
msanEnergyMeterEnergySumEntry	1.3.6.1.4.1.1332.1.1.5.3.107.3.1		not-accessible	Description.
U32 msanEnergyMeterEnergySumValue	1.3.6.1.4.1.1332.1.1.5.3.107.3.1.1	Unsigned32	read-only	Energy sum value of all tariffs
msanArpInspection	1.3.6.1.4.1.1332.1.1.5.3.108
msanArpInspectionGlobal	1.3.6.1.4.1.1332.1.1.5.3.108.1
INT msanArpInspectionAdminMode	1.3.6.1.4.1.1332.1.1.5.3.108.1.1	INTEGER	read-write	Enable/disable global dynamic arp inspection
msanArpInspectionPortTable	1.3.6.1.4.1.1332.1.1.5.3.108.2		not-accessible	Arp Inspection.
msanArpInspectionPortEntry	1.3.6.1.4.1.1332.1.1.5.3.108.2.1		not-accessible	Description.
INT msanArpInspectionPortAdminMode	1.3.6.1.4.1.1332.1.1.5.3.108.2.1.1	INTEGER	read-write	Enable/disable dynamic arp inspection for the selected interface.
INT msanArpInspectionPortStatDroppedFrames	1.3.6.1.4.1.1332.1.1.5.3.108.2.1.2	INTEGER	read-only	Number of discarded ARP packets on interface.
msanArpInspectionVlanTable	1.3.6.1.4.1.1332.1.1.5.3.108.3		not-accessible	Arp Inspection.
msanArpInspectionVlanEntry	1.3.6.1.4.1.1332.1.1.5.3.108.3.1		not-accessible	Description.
INT msanArpInspectionVlanAdminMode	1.3.6.1.4.1.1332.1.1.5.3.108.3.1.1	INTEGER	read-write	Enable/disable dynamic arp inspection per vlan.
INT msanArpInspectionVlanStatDroppedFrames	1.3.6.1.4.1.1332.1.1.5.3.108.3.1.2	INTEGER	read-only	Number of discarded ARP packets per vlan.
msanIsa	1.3.6.1.4.1.1332.1.1.5.3.109
msanIsaGlobal	1.3.6.1.4.1.1332.1.1.5.3.109.1
INT msanIsaTalAdminMode	1.3.6.1.4.1.1332.1.1.5.3.109.1.1	INTEGER	read-write	ISA TAL functionality global admin mode.
U32 msanIsaDasServerPort	1.3.6.1.4.1.1332.1.1.5.3.109.1.2	Unsigned32	read-write	ISA Radius DAS (Dynamic Authorization Server) port number.
STR msanIsaDasServerSecret	1.3.6.1.4.1.1332.1.1.5.3.109.1.3	DisplayString	read-write	ISA Radius DAS (Dynamic Authorization Server) shared secret.
U32 msanIsaRadiusServerRetries	1.3.6.1.4.1.1332.1.1.5.3.109.1.4	Unsigned32	read-write	Maximum number of retransmissions of a ISA Radius request packet.
U32 msanIsaRadiusServerTimeout	1.3.6.1.4.1.1332.1.1.5.3.109.1.5	Unsigned32	read-write	Time out duration (in seconds) before packets are retransmitted to ISA Radius server
msanIsaStatistics	1.3.6.1.4.1.1332.1.1.5.3.109.2
msanIsaPortStatTable	1.3.6.1.4.1.1332.1.1.5.3.109.2.1		not-accessible	Description.
msanIsaPortStatEntry	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1		not-accessible	Description.
C32 msanIsaPortStatTalMatchedFrames	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.1	Counter32	read-only	Number of TAL matched frames.
C32 msanIsaPortStatTalDroppedFrames	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.2	Counter32	read-only	Number of TAL dropped frames.
C32 msanIsaPortStatAuthenReqSent	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.3	Counter32	read-only	Number of sent Authentication requests.
C32 msanIsaPortStatAuthenReqConfirmed	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.4	Counter32	read-only	Number of confirmed Authentication requests.
C32 msanIsaPortStatAuthenReqRejected	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.6	Counter32	read-only	Number of rejected Authentication requests.
C32 msanIsaPortStatAuthenTimeoutExpired	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.7	Counter32	read-only	Number of expired Authentication timeouts.
C32 msanIsaPortStatAuthorReqSent	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.8	Counter32	read-only	Number of sent Authorization requests.
C32 msanIsaPortStatAuthorReqConfirmed	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.9	Counter32	read-only	Number of confirmed Authorization requests.
C32 msanIsaPortStatAuthorReqRejected	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.10	Counter32	read-only	Number of rejected Authorization requests.
C32 msanIsaPortStatAuthorTimeoutExpired	1.3.6.1.4.1.1332.1.1.5.3.109.2.1.1.11	Counter32	read-only	Number of expired Authorization timeouts.
C32 msanIsaStatLoginReq	1.3.6.1.4.1.1332.1.1.5.3.109.2.2	Counter32	read-only	Cumulative number of Login requests.
C32 msanIsaStatLoginUnsuccessfulReq	1.3.6.1.4.1.1332.1.1.5.3.109.2.3	Counter32	read-only	Number of unsuccessful login requests.
msanIsaRadiusServerTable	1.3.6.1.4.1.1332.1.1.5.3.109.3		not-accessible	Description.
msanIsaRadiusServerEntry	1.3.6.1.4.1.1332.1.1.5.3.109.3.1		not-accessible	Description.
IP msanIsaRadiusServerIpAddress	1.3.6.1.4.1.1332.1.1.5.3.109.3.1.1	IpAddress	not-accessible	ISA Radius server IP address.
INT msanIsaRadiusServerType	1.3.6.1.4.1.1332.1.1.5.3.109.3.1.2	INTEGER	not-accessible	ISA Radius server type.
U32 msanIsaRadiusServerPort	1.3.6.1.4.1.1332.1.1.5.3.109.3.1.3	Unsigned32	read-write	ISA Radius server port number. If msanIsaRadiusServerType = authentication(1) then default port value is 1812. If msanIsaRadiusServerType = accounting(2) then default port value is 1813.
STR msanIsaRadiusServerSecret	1.3.6.1.4.1.1332.1.1.5.3.109.3.1.4	DisplayString	read-write	ISA Radius server shared secret.
INT msanIsaRadiusServerPrimaryMode	1.3.6.1.4.1.1332.1.1.5.3.109.3.1.5	INTEGER	read-write	ISA Radius server primary mode. Only one server can be defined as primary(1).
ROW msanIsaRadiusServerRowStatus	1.3.6.1.4.1.1332.1.1.5.3.109.3.1.6	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation parameter msanIsaRadiusServerType must be defined.
msanIsaPortTable	1.3.6.1.4.1.1332.1.1.5.3.109.5		not-accessible	Description.
msanIsaPortEntry	1.3.6.1.4.1.1332.1.1.5.3.109.5.1		not-accessible	Description.
INT msanIsaPortTalAdminMode	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.1	INTEGER	read-write	ISA TAL functionality admin mode.
INT msanIsaPortAuthentication	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.2	INTEGER	read-write	ISA Authentication administrative state.
INT msanIsaPortAuthorization	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.3	INTEGER	read-write	ISA Authorization administrative state.
INT msanIsaPortAccounting	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.4	INTEGER	read-write	ISA Accounting administrative state.
BIT msanIsaPortLoginMask	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.5	Bits	read-write	ISA login mask.
OCT msanIsaPortLoginUserPatternMask	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.6	OCTET STRING	read-write	This mask value identifies the portion of input packet that is send to Radius server, if userPattern bit is set in msanIsaPortLoginMask. Empty string indicates that parameter has not been defined.
INT msanIsaPortTalAutomaticReq	1.3.6.1.4.1.1332.1.1.5.3.109.5.1.7	INTEGER	read-write	TAL automatic request state.
msanIsaTalPortMatchTable	1.3.6.1.4.1.1332.1.1.5.3.109.6		not-accessible	Description.
msanIsaTalPortMatchEntry	1.3.6.1.4.1.1332.1.1.5.3.109.6.1		not-accessible	Description.
I32 msanIsaTalPortMatchEthertype	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.1	Integer32	read-write	Match incoming packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined.
MAC msanIsaTalPortMatchMacSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.2	MacAddress	read-write	Match incoming packet frame with specified Source MAC address. Empty string indicates that parameter has not been defined.
MAC msanIsaTalPortMatchMacSrcMask	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.3	MacAddress	read-write	This mask value identifies the portion of msanIsaTalPortMatchMacSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined
I32 msanIsaTalPortMatchVlanId	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.4	Integer32	read-write	Match incoming packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined
IP msanIsaTalPortMatchIpSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.5	IpAddress	read-write	Match incoming packet frame with specified source IP address. Empty string indicates that parameter has not been defined.
IP msanIsaTalPortMatchIpSrcMask	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.6	IpAddress	read-write	This mask value identifies the portion of msanIsaTalPortMatchIpSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined
INT msanIsaTalPortMatchDhcpType	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.7	INTEGER	read-write	Match incoming packet frame with specified DHCP type value.
STR msanIsaTalPortMatchDhcpOpt60VendorId	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.8	DisplayString	read-write	Match incoming packet frame with specified DHCP option 60 vendorId value. Empty string indicates that parameter has not been defined.
STR msanIsaTalPortMatchDhcpOpt61ClientId	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.9	DisplayString	read-write	Match incoming packet frame with specified DHCP option 61 clientId value. Empty string indicates that parameter has not been defined.
MAC msanIsaTalPortMatchDhcpOpt61ClientIdMacAddr	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.10	MacAddress	read-write	Match incoming packet frame with specified DHCP option 61 MAC address. Empty string indicates that parameter has not been defined.
STR msanIsaTalPortMatchDhcpOpt82RemoteId	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.11	DisplayString	read-write	Match incoming packet frame with specified DHCP option 82 remoteId value. Empty string indicates that parameter has not been defined.
OCT msanIsaTalPortMatchUserBits	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.12	OCTET STRING	read-write	Match incoming packet frame with specified user defined bits. Empty string indicates that parameter has not been defined.
OCT msanIsaTalPortMatchUserMask	1.3.6.1.4.1.1332.1.1.5.3.109.6.1.13	OCTET STRING	read-write	This mask value identifies the portion of msanIsaTalPortMatchUserBits that is compared with input packet. Empty string indicates that parameter has not been defined.
msanIsaTalPatternMatchTable	1.3.6.1.4.1.1332.1.1.5.3.109.7		not-accessible	This table is used to store the pattern match name, pattern rules and the corresponding login mask for the pattern match.
msanIsaTalPatternMatchEntry	1.3.6.1.4.1.1332.1.1.5.3.109.7.1		not-accessible	Each entry in this table contains the a unique pattern match along with the loginmask to identify the user login packets.
OCT msanIsaTalPatternMatchName	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.1	OCTET STRING	not-accessible	Pattern match name.
I32 msanIsaTalPatternMatchEthertype	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.2	Integer32	read-write	Match incoming packet frame with specified EtherType value. A value of -1 indicates that parameter has not been defined.
MAC msanIsaTalPatternMatchMacSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.3	MacAddress	read-write	Match incoming packet frame with specified Source MAC address. Empty string indicates that parameter has not been defined.
MAC msanIsaTalPatternMatchMacSrcMask	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.4	MacAddress	read-write	This mask value identifies the portion of msanIsaTalPatternMatchMacSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined
I32 msanIsaTalPatternMatchVlanId	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.5	Integer32	read-write	Match incoming packet frame with specified VLAN ID value (1-4094). A value of -1 indicates that parameter has not been defined
IP msanIsaTalPatternMatchIpSrcAddr	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.6	IpAddress	read-write	Match incoming packet frame with specified source IP address. Empty string indicates that parameter has not been defined.
IP msanIsaTalPatternMatchIpSrcMask	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.7	IpAddress	read-write	This mask value identifies the portion of msanIsaTalPatternMatchIpSrcAddr that is compared with input packet. Empty string indicates that parameter has not been defined
INT msanIsaTalPatternMatchDhcpType	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.8	INTEGER	read-write	Match incoming packet frame with specified DHCP type value.
STR msanIsaTalPatternMatchDhcpOpt60VendorId	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.9	DisplayString	read-write	Match incoming packet frame with specified DHCP option 60 vendorId value. Empty string indicates that parameter has not been defined.
STR msanIsaTalPatternMatchDhcpOpt61ClientId	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.10	DisplayString	read-write	Match incoming packet frame with specified DHCP option 61 clientId value. Empty string indicates that parameter has not been defined.
MAC msanIsaTalPatternMatchDhcpOpt61ClientIdMacAddr	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.11	MacAddress	read-write	Match incoming packet frame with specified DHCP option 61 MAC address. Empty string indicates that parameter has not been defined.
STR msanIsaTalPatternMatchDhcpOpt82RemoteId	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.12	DisplayString	read-write	Match incoming packet frame with specified DHCP option 82 remoteId value. Empty string indicates that parameter has not been defined.
OCT msanIsaTalPatternMatchUserBits	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.13	OCTET STRING	read-write	Match incoming packet frame with specified user defined bits. Empty string indicates that parameter has not been defined.
OCT msanIsaTalPatternMatchUserMask	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.14	OCTET STRING	read-write	This mask value identifies the portion of msanIsaTalPatternMatchUserBits that is compared with input packet. Empty string indicates that parameter has not been defined.
BIT msanIsaTalPatternMatchLoginMask	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.15	Bits	read-write	Login mask for the current pattern match. This is used to generate the UserId.
ROW msanIsaTalPatternMatchRowStatus	1.3.6.1.4.1.1332.1.1.5.3.109.7.1.16	RowStatus	read-write	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. A new row is created using createAndWait(5) [createAndGo(4) is not supported] The value active(1) activates the entry. Setting this object to destroy6) will remove this entry.
msanIsaTalPortPatternMatchTable	1.3.6.1.4.1.1332.1.1.5.3.109.8		not-accessible	A connection between Pattern Matches and device ports. An entry is created in this table whenever a pattern match need to be attached to a downlink port.
msanIsaTalPortPatternMatchEntry	1.3.6.1.4.1.1332.1.1.5.3.109.8.1		not-accessible	Each entry in this table contains the a unique pattern match on a port along with the loginmask to identify the user login packets.
ROW msanIsaTalPortPatternMatchRowStatus	1.3.6.1.4.1.1332.1.1.5.3.109.8.1.1	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) creates a row in this table. Setting this object to destroy(6) will remove this entry. Read values: active(1). Other values are currently not supported.
msanSync	1.3.6.1.4.1.1332.1.1.5.3.110
msanSyncGlobal	1.3.6.1.4.1.1332.1.1.5.3.110.1
msanSyncTable	1.3.6.1.4.1.1332.1.1.5.3.110.2		not-accessible	Description.
msanSyncEntry	1.3.6.1.4.1.1332.1.1.5.3.110.2.1		not-accessible	Description.
INT msanSyncBoardPosition	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.1	INTEGER	not-accessible	Central ethernet board position.
INT msanSyncSourcePriority	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.2	INTEGER	not-accessible	Synchronization source priority: 1-first priority, 2-second priority.....
INT msanSyncSourceType	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.3	INTEGER	read-write	Synchronization source type: ext-2mhz(4) - synchronization on extended source 2MHz, ext-10mhz(5) - synchronization on extended source 10MHz, ext-1hz(6) - synchronization on extended source 1Hz, mlvds-bp(8) - synchronization on MLVDS, pps-bp(14) - synchronization on PPS, ptp-eth(15)- synchronization on PtP Ethernet, sync-eth(16) - synchronization on Synchronous Ethernet, free-run(40) - free-run synchronization
INT msanSyncSourceId	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.4	INTEGER	read-write	Synchronization source identity. msanSyncSourceId can be used when msanSyncSourceType has one of values: - ext-2mhz(4), - ext-10mhz(5), - ext-1hz(6), - mlvds-bp(8), - pps-bp(14), - free-run(40) msanSyncSourceId can be set only to input-1(1), when msanSyncSourceType is pps-bp(14) or free-run(40).
NUM msanSyncSourceEthPortId	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.5	InterfaceIndex	read-write	Synchronization source ethernet Port Id (value of ifIndex). msanSyncSourceEthPortId can be used, when msanSyncSourceType has ptp-eth(15) or sync-eth(16) value.
INT msanSyncDestinationType	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.6	INTEGER	read-write	Synchronization destination type: local(0) - synchronization signal is used only on local board global(0) - synchronization signal is sent to MLVDS bus
INT msanSyncDestinationMlvdsId	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.7	INTEGER	read-write	Destination MLVDS bus Identity. This parameter is used when msanSyncDestinationType has global(1) value.
INT msanSyncSourceSuitability	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.8	INTEGER	read-only	Source Suitability.
INT msanSyncSourceActivity	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.9	INTEGER	read-only	Source Activity .
ROW msanSyncRowStatus	1.3.6.1.4.1.1332.1.1.5.3.110.2.1.10	RowStatus	read-create	The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. For row creation use createAndWait(5). For row activation use active(1). For row deletion use destroy(6). Other values are currently not supported. For row activation next terms must be defined - msanSyncSourceType - msanSyncSourceMlvdsId or msanSyncSourcePortId - msanSyncDestionationType - msanSyncDestionaMlvdsId if msanSyncDestionType=global(10)

RFC description

Iskratel vendor MIB for managing MSAN (Multi-Service Access Node) platforms used in broadband and voice services.

Start monitoring Iskratel multi-service access node (MSAN) platform with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ISKRATEL-MSAN-MIB

What Is ISKRATEL-MSAN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description