ICOTERA-I6800-SERIES

All MIBs › ICOTERA-I6800-SERIES

Organization: Icotera A/S

Last Updated: 2016-03-11

Category: DSL and Broadband, Vendor: Icotera

Description: Icotera MIB for the I6800 series residential gateway providing broadband interface monitoring and home network management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ICOTERA-I6800-SERIES?

ICOTERA-I6800-SERIES is a vendor-specific MIB from Icotera for its I6800 series residential/DOCSIS gateway (cable modem/router) product line. It exposes objects covering the cable/CATV RF interface (module admin status, RF filter, RF level, signal detection, power level, output level, OMI), VoIP FXS port lines, and device management/upgrade functions. For monitoring hardware and software status, this MIB is quite rich: it lets an operator check whether the CATV/cable module is administratively up, whether the incoming RF signal is present and at an acceptable power/signal level, and it also exposes device operations like factory reset and firmware upgrade URL, which reflect configuration/software-management state. As a broadband CPE MIB it likely coexists with or is layered over DOCSIS-related standard MIBs for the cable interface, though it is largely a proprietary/vendor extension. It is typically deployed on Icotera-branded residential gateways provisioned by cable/MSO operators for home broadband and VoIP service delivery. Engineers can download the ICOTERA-I6800-SERIES file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ICOTERA-I6800-SERIES. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Icotera I6800 series residential gateway/cable modem

Monitoring Examples

An MSO's monitoring system would poll catvModuleSignalDetected and catvModuleRflevel/catvModulePowerLevel per gateway to confirm the cable RF signal is present and within spec, flagging catvModuleLowSignal when a subscriber's line degrades due to a bad connector or cable fault. voipFXSport1 and voipFXSport2 status would be checked to confirm the analog phone lines are registered and operational for VoIP service. The performFactoryReset and upgUrl objects would be used administratively to trigger a reset or point the device at a new firmware image rather than for passive monitoring.

What Can Be Monitored

CATV/RF module admin status
RF signal level and power level
low signal / signal detected alarms
VoIP FXS port status
firmware upgrade URL/version
factory reset state

Imported Objects

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
enterprises

From SNMPv2-TC

MacAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
icotera	1.3.6.1.4.1.29865			The Icotera management information base SMI definitions
ictIGW4k	1.3.6.1.4.1.29865.12			Device related SNMP options
ictMgmt	1.3.6.1.4.1.29865.12.2
ictMgmtMib	1.3.6.1.4.1.29865.12.2.1			The MIB which allows managing the CPE
ictFwUpg	1.3.6.1.4.1.29865.12.2.1.1			The MIB of firmware upgrade
OCT upgUrl	1.3.6.1.4.1.29865.12.2.1.1.1	OCTET STRING	read-write	Path to file with firmware.
INT upgExecute	1.3.6.1.4.1.29865.12.2.1.1.2	INTEGER	read-write	MIB responsible for trigerring firmware upgrade.
OCT upgStatus	1.3.6.1.4.1.29865.12.2.1.1.3	OCTET STRING	read-only	MIB show upgrade status.
ictCfgUpdate	1.3.6.1.4.1.29865.12.2.1.2			The MIB of configuration update
OCT cfgTftpPath	1.3.6.1.4.1.29865.12.2.1.2.1	OCTET STRING	read-write	Path to cofiguration file stored at TFTP server.
INT cfgExecute	1.3.6.1.4.1.29865.12.2.1.2.2	INTEGER	read-write	MIB responsible for trigerring config upload at CPE.
OCT cfgStatus	1.3.6.1.4.1.29865.12.2.1.2.3	OCTET STRING	read-only	MIB show configuration upgrade status.
ictReboot	1.3.6.1.4.1.29865.12.2.1.3			The MIB responsible for CPE reboot
INT performCpeReboot	1.3.6.1.4.1.29865.12.2.1.3.2	INTEGER	read-write	MIB responsible for trigerring CPE reboot.
ictServices	1.3.6.1.4.1.29865.12.3
ictCatv	1.3.6.1.4.1.29865.12.3.1			The MIB module for managing Icotera services
ictCatvMib	1.3.6.1.4.1.29865.12.3.1.1			The MIB module for managing Icotera services
INT catvModuleAdminStatus	1.3.6.1.4.1.29865.12.3.1.1.1	INTEGER	read-only	The administrative status of the module, this can be enabled(1) or disabled(0).
INT catvModuleFilter	1.3.6.1.4.1.29865.12.3.1.1.2	INTEGER	read-only	Package filter selected for catv module
INT catvModuleRflevel	1.3.6.1.4.1.29865.12.3.1.1.3	INTEGER	read-only	RF signal amplification on CATV output
INT catvModuleLowSignal	1.3.6.1.4.1.29865.12.3.1.1.4	INTEGER	read-only	Low signal level of catv led
INT catvModuleSignalDetected	1.3.6.1.4.1.29865.12.3.1.1.5	INTEGER	read-only	Tells whether CATV signal is detected: yes(1) - detected, no(0) - not detected.
INT catvModulePowerLevel	1.3.6.1.4.1.29865.12.3.1.1.6	INTEGER	read-only	Current CATV power level. It can have one of the following values: - any integer between -1299 and 199 when the power level is higher than -13.00 and lower than 2.00, which is the power level in dBm multiplied by 100. - a value of -2147483648 when the power level is lower than -13 dBm - a value of 2147483647 when the power level is higher than 2 dBm.
INT catvModuleRfOutputLevel	1.3.6.1.4.1.29865.12.3.1.1.7	INTEGER	read-only	Parameter is supported by special CATV solution. No data will be provided if CPE is not compatible. Calculated RF output value which should be expected. - Expected value is presented in dBuV multiplied by 100. - if value of 0 is received, either CATV fiber is not connected or CATV is turned off.
INT catvModuleOmi	1.3.6.1.4.1.29865.12.3.1.1.8	INTEGER	read-only	Parameter is supported by special CATV solution. No data will be provided if CPE is not compatible. Currently OMI value set at CPE.
ictVoip	1.3.6.1.4.1.29865.12.3.2			The MIB module for checking VoIP service
ictVoipMib	1.3.6.1.4.1.29865.12.3.2.1			The MIB module for checking VoIP service status
OCT voipFXSport1	1.3.6.1.4.1.29865.12.3.2.1.1	OCTET STRING	read-only	The administrative status of the FXS port 1
OCT voipFXSport2	1.3.6.1.4.1.29865.12.3.2.1.2	OCTET STRING	read-only	The administrative status of the FXS port 2
ictDuplex	1.3.6.1.4.1.29865.12.4
ictDuplexMib	1.3.6.1.4.1.29865.12.4.15			Initial release.
duplexConfig	1.3.6.1.4.1.29865.12.4.15.1
ifDuplexTable	1.3.6.1.4.1.29865.12.4.15.1.1		not-accessible	A table containing interface duplex status.
ifDuplexEntry	1.3.6.1.4.1.29865.12.4.15.1.1.1		not-accessible	Status for a specific interface using ethernet-like medium.
NUM ifDuplexIndex	1.3.6.1.4.1.29865.12.4.15.1.1.1.1	InterfaceIndex	read-only	An index value that uniquely identifies an interface to an ethernet-like medium. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
INT ifDuplexStatus	1.3.6.1.4.1.29865.12.4.15.1.1.1.2	INTEGER	read-only	The current duplex mode of operation of the interface. 'unknown' indicates that the current duplex mode could not be determined.
ictReset	1.3.6.1.4.1.29865.12.5
ictFacRst	1.3.6.1.4.1.29865.12.5.1			The MIB parent for CPE reset
ictFacRstMib	1.3.6.1.4.1.29865.12.5.1.1			The MIB which makes Factory Reset of CPE
INT performFactoryReset	1.3.6.1.4.1.29865.12.5.1.1.1	INTEGER	read-write	Status of FactoryReset feature.
ictDhcp	1.3.6.1.4.1.29865.12.6
ictDHCPsrv	1.3.6.1.4.1.29865.12.6.1		not-accessible	Table of DHCPd leases.
ictDHCPsrvLeases	1.3.6.1.4.1.29865.12.6.1.1		not-accessible	An entry in the table, containing information about lease.
INT ictDHCPsrvIndex	1.3.6.1.4.1.29865.12.6.1.1.1	INTEGER	read-only	A unique value for LEASE index.
MAC ictMacAddress	1.3.6.1.4.1.29865.12.6.1.1.2	MacAddress	read-only	MAC address of Lease.
INT ictExpire	1.3.6.1.4.1.29865.12.6.1.1.3	INTEGER	read-only	Lease time until Expire
STR ictIPaddress	1.3.6.1.4.1.29865.12.6.1.1.4	DisplayString	read-only	IP address learned from host.
STR ictHostName	1.3.6.1.4.1.29865.12.6.1.1.5	DisplayString	read-only	Hostname.

RFC description

Management information base for Icotera i6800 series CATV customer premise equipment.

Start monitoring Icotera I6800 series residential gateway/cable modem with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ICOTERA-I6800-SERIES

What Is ICOTERA-I6800-SERIES?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description