HUAWEI-VO-DIAL-CONTROL-MIB

All MIBs › HUAWEI-VO-DIAL-CONTROL-MIB

Organization: Huawei-3COM Technologies Co., Ltd.

Last Updated: 2004-10-20

Category: Domain: Telephony/VoIP, Domain: VoIP/Telephony, Vendor: Huawei

Description: Huawei voice dial control MIB for managing dial peer configuration, destination patterns, and VOIP/POTS call routing.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-VO-DIAL-CONTROL-MIB?

HUAWEI-VO-DIAL-CONTROL-MIB is a Huawei enterprise MIB for voice-over-X dial control, managing dial-peer configuration, destination patterns, and call routing between VoIP and traditional POTS (Plain Old Telephone Service) legs on Huawei voice gateways. It exposes configuration objects describing how dial peers map dialed digit patterns to specific voice interfaces or VoIP destinations, i.e., the call-routing logic of the device. Its monitoring value is largely software-configuration verification: confirming dial peers are correctly defined and matched, and, where call-state objects exist, checking whether calls are routing successfully rather than failing due to pattern mismatches or peer misconfiguration. It relies on and works alongside related voice MIBs such as HUAWEI-VO-IF-MIB and HUAWEI-VOICEPORT-MIB, which define the physical/logical voice endpoints these dial peers reference. Deployment context is Huawei voice gateways or integrated access devices providing VoIP-to-PSTN interworking for enterprise or carrier telephony. Network engineers evaluating or troubleshooting this functionality can download the HUAWEI-VO-DIAL-CONTROL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-VO-DIAL-CONTROL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei voice gateway
Huawei integrated access device

Monitoring Examples

An administrator would inspect dial-peer and destination-pattern configuration objects to confirm that a specific dialed number pattern is correctly routed to the intended VoIP or POTS destination, and a call failure would be diagnosed by finding a missing or overlapping dial-peer pattern entry.

What Can Be Monitored

dial peer configuration
destination pattern mapping
call routing status

Imported Objects

From HUAWEI-3COM-OID-MIB

voice

OBJECT-IDENTITY

From SNMPv2-SMI

IpAddress
MODULE-IDENTITY
OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwVoiceDialControlMIB	1.3.6.1.4.1.2011.5.25.1.5
hwVoPeerCommonConfigEntry	1.3.6.1.4.1.2011.5.25.1.5.1.1.1		not-accessible	The common informatioin of voice peer.
hwVoPeerCommonConfigTable	1.3.6.1.4.1.2011.5.25.1.5.1.1		not-accessible	The table contains the voice peer common information .
INT hwVoPeerConfigAuthorizationLevel	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.25	INTEGER	read-write	This object specifies the caller level for local authorization. The level is between 0 and 9. The highest level is 9, the lowest level is 0, and 0 is the default value.
INT hwVoPeerConfigCalledNumberingPlan	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.30	INTEGER	read-write	This object specifies the numbering plan of called number about this voice entity. data - data numbering plan. isdn - ISDN/telephone numbering plan. national - national standard numbering plan. private - Private numbering plan. reserved - Reserved for extension. telex - telex numbering plan. unknown - unknown.
INT hwVoPeerConfigCalledNumberType	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.28	INTEGER	read-write	This object specifies the numbering type of called number about this voice entity. abbreviated - the numbering type is abbreviated. international - the numbering type is international. national - the numbering type is national. network - the numbering type is network. reserved - the numbering type is reserved. subscriber - the numbering type is subscriber. unknown - the numbering type is unkown.
INT hwVoPeerConfigCalledNumSubstRule	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.33	INTEGER	read-write	This object specifies number-substitute rule that apply called number of this voice entity. It is valid if its value is between 1 and 2147483647. This voice entity doesn't apply any number-substitute rule if its value is 0.
OCT hwVoPeerConfigCallerPermitNum	1.3.6.1.4.1.2011.5.25.1.5.1.5.1.1	OCTET STRING	read-write	This object specifies caller number permitted that must be of the form ^(([0-9ABCD#*.!+%[]()\-]+(\$)!)\|(\$))$. Specially set this object $ meaning allow caller null.
hwVoPeerConfigCallerPermitNumEntry	1.3.6.1.4.1.2011.5.25.1.5.1.5.1		not-accessible	A single caller number permitted in the specific voice entity for incoming call. The entry is created when its associated voPeerCommonCfgEntry is created. This entry is deleted when its associated voPeerCommonCfgEntry is deleted.
ENT hwVoPeerConfigCallerPermitNumRowStatus	1.3.6.1.4.1.2011.5.25.1.5.1.5.1.2	EntryStatus	read-write	This object is used to create a new row or modify or delete an existing row in this table.
hwVoPeerConfigCallerPermitNumTable	1.3.6.1.4.1.2011.5.25.1.5.1.5		not-accessible	The table contains caller number permitted information in the specific voice entity for incoming call.
INT hwVoPeerConfigCallingNumberingPlan	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.29	INTEGER	read-write	This object specifies the numbering plan of calling number about this voice entity. data - data numbering plan. isdn - ISDN/telephone numbering plan. national - national standard numbering plan. private - Private numbering plan. reserved - Reserved for extension. telex - telex numbering plan. unknown - unknown.
INT hwVoPeerConfigCallingNumberType	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.27	INTEGER	read-write	This object specifies the numbering type of calling number about this voice entity. abbreviated - the numbering type is abbreviated. international - the numbering type is international. national - the numbering type is national. network - the numbering type is network. reserved - the numbering type is reserved. subscriber - the numbering type is subscriber. unknown - the numbering type is unkown.
INT hwVoPeerConfigCallingNumSubstRule	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.32	INTEGER	read-write	This object specifies number-substitute rule that apply calling number of this voice entity. It is valid if its value is between 1 and 2147483647. This voice entity doesn't apply any number-substitute rule if its value is 0.
INT hwVoPeerConfigCodec1st	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.4	INTEGER	read-write	This object expresses the first desirable codec of speech for the peer.
INT hwVoPeerConfigCodec2st	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.5	INTEGER	read-write	This object expresses the second desirable codec of speech for the peer.
INT hwVoPeerConfigCodec3st	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.6	INTEGER	read-write	This object expresses the third desirable codec of speech for the peer.
INT hwVoPeerConfigCodec4st	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.7	INTEGER	read-write	This object expresses the forth desirable codec with of speech for the peer.
OCT hwVoPeerConfigDescription	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.26	OCTET STRING	read-write	This object specifies the textual description of this voice entity.
OCT hwVoPeerConfigDesPattern	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.3	OCTET STRING	read-write	The number associated with this voice peer.Character include '0' to '9','*','#','+','.','T' can be configured in this number.
INT hwVoPeerConfigDtmfRelay	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.11	INTEGER	read-write	set the DTMF relay type in this dial-peer.
INT hwVoPeerConfigFaxLevel	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.12	INTEGER	read-write	This object expresses the fax level in this dial-peer.
INT hwVoPeerConfigFaxLocalTrainParam	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.14	INTEGER	read-write	This object expresses the fax local train threshold in this dial-peer. The default value is 10.
INT hwVoPeerConfigFaxPassthroughMode	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.23	INTEGER	read-write	set pcm fax protocol passthrough mode It is valid only when fax protocol is pcm .
INT hwVoPeerConfigFaxProtocol	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.15	INTEGER	read-write	This object expresses the fax protocol which this dial-peer support. The default value is t38.
INT hwVoPeerConfigFaxRate	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.13	INTEGER	read-write	This object expresses the fax transmit rate.
INT hwVoPeerConfigFaxRelay	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.21	INTEGER	read-write	This object expresses ecm mode is used in fax transmit or not.
INT hwVoPeerConfigFaxSendNSFSwitch	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.18	INTEGER	read-write	This object expresses whether or not send nsf to fax in this dial-peer.
INT hwVoPeerConfigFaxSupportMode	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.19	INTEGER	read-write	This object expresses the fax support mode in this dial-peer.
INT hwVoPeerConfigFaxT38HighRedunPackNumber	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.16	INTEGER	read-write	This object expresses the high speed redundancy packet numbers when t38 fax protocol is used for this dial-peer .
INT hwVoPeerConfigFaxT38LowRedunPackNumber	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.17	INTEGER	read-write	This object expresses the low speed redundancy packet numbers when t38 fax protocol is used for this dial-peer .
INT hwVoPeerConfigFaxTrainMode	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.20	INTEGER	read-write	This object expresses the fax train mode in this dial-peer.
INT hwVoPeerConfigIndex	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.1	INTEGER	read-only	Index of voice peer common table. It identify the number of the voice peer.
INT hwVoPeerConfigIpPreced	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.8	INTEGER	read-write	This object expresses the ip precedence of voice packets. The default value is 0.
INT hwVoPeerConfigMaxCall	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.34	INTEGER	read-write	The object specifies that this voice entity is bound with a tag that indicates a maximum call value. The value of 0 specifies that cancel the act of binding.
INT hwVoPeerConfigPriority	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.24	INTEGER	read-write	This object specifies the priority of this voice entity. It is between 0 and 10. The highest priority is 0, the lowest priority is 10, and 0 is the default value.
ENT hwVoPeerConfigRowStatus	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.22	EntryStatus	read-write	This object specifies the status of this conceptual row, which is used to create a new row or modify or delete an existing row in this table.
INT hwVoPeerConfigSelectStop	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.31	INTEGER	read-write	This object specifies no further entity searching allowed if a call started on the this voice entity.
INT hwVoPeerConfigShutDown	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.9	INTEGER	read-write	This object expresses the current status of the peer.
INT hwVoPeerConfigType	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.2	INTEGER	read-write	Specify the type of voice peer.
INT hwVoPeerConfigVADSwitch	1.3.6.1.4.1.2011.5.25.1.5.1.1.1.10	INTEGER	read-write	Enable or disable the VAD (Voice Activity Detection).
INT hwVoPeerDefaultConfig1STCodecLevel	1.3.6.1.4.1.2011.5.25.1.5.1.4.2	INTEGER	read-write	The default value of voice entity 1st codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
INT hwVoPeerDefaultConfig2NDCodecLevel	1.3.6.1.4.1.2011.5.25.1.5.1.4.3	INTEGER	read-write	The default value of voice entity 2nd codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
INT hwVoPeerDefaultConfig3RDCodecLevel	1.3.6.1.4.1.2011.5.25.1.5.1.4.4	INTEGER	read-write	The default value of voice entity 3rd codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
INT hwVoPeerDefaultConfig4THCodecLevel	1.3.6.1.4.1.2011.5.25.1.5.1.4.5	INTEGER	read-write	The default value of voice entity 4th codec level priority g711alaw G.711 A Law 64000 bps g711ulaw G.711 U Law 64000 bps g723r53 G.723.1 5300 bps g723r63 G.723.1 6300 bps g729r8 G.729 8000 bps g729a G.729 A
INT hwVoPeerDefaultConfigCancelTrun	1.3.6.1.4.1.2011.5.25.1.5.1.4.1	INTEGER	read-write	The default value of dial peer's Cancel trun
INT hwVoPeerDefaultConfigFaxBaudrate	1.3.6.1.4.1.2011.5.25.1.5.1.4.12	INTEGER	read-write	The default value of dial peer's Fax Baudrate .
INT hwVoPeerDefaultConfigFaxECM	1.3.6.1.4.1.2011.5.25.1.5.1.4.16	INTEGER	read-write	The default value of fax ECM Mode .
INT hwVoPeerDefaultConfigFaxHSRedundancy	1.3.6.1.4.1.2011.5.25.1.5.1.4.10	INTEGER	read-write	The default value of dial peer's T38 Fax Protocol High Redundancy.
INT hwVoPeerDefaultConfigFaxLocalTrain	1.3.6.1.4.1.2011.5.25.1.5.1.4.8	INTEGER	read-write	The default value of dial peer's Fax local train threshold .
INT hwVoPeerDefaultConfigFaxLSRedundancy	1.3.6.1.4.1.2011.5.25.1.5.1.4.11	INTEGER	read-write	The default value of dial peer's T38 Fax Protocol Low Redundancy.
INT hwVoPeerDefaultConfigFaxNSF	1.3.6.1.4.1.2011.5.25.1.5.1.4.13	INTEGER	read-write	The default value of fax non-standard faculty .
INT hwVoPeerDefaultConfigFaxProtocol	1.3.6.1.4.1.2011.5.25.1.5.1.4.9	INTEGER	read-write	The default value of dial peer's Fax Protocol .
INT hwVoPeerDefaultConfigFaxSupportMode	1.3.6.1.4.1.2011.5.25.1.5.1.4.14	INTEGER	read-write	The default value of fax SupportMode .
INT hwVoPeerDefaultConfigFaxTrainMode	1.3.6.1.4.1.2011.5.25.1.5.1.4.15	INTEGER	read-write	The default value of fax TrainMode .
INT hwVoPeerDefaultConfigFaxTransmitLevel	1.3.6.1.4.1.2011.5.25.1.5.1.4.7	INTEGER	read-write	The default value of dial peer's FaxTransmitLevel.The unit is db
hwVoPeerDefaultConfigObjects	1.3.6.1.4.1.2011.5.25.1.5.1.4
INT hwVoPeerDefaultConfigVADOn	1.3.6.1.4.1.2011.5.25.1.5.1.4.6	INTEGER	read-write	The default value of dial peer's VAD Switch
hwVoPeerObjects	1.3.6.1.4.1.2011.5.25.1.5.1
INT hwVoPOTSPeerConfigCancelTruncateEnable	1.3.6.1.4.1.2011.5.25.1.5.1.2.1.2	INTEGER	read-write	Cancel truncate the called number in this dial-peer.
hwVoPOTSPeerConfigEntry	1.3.6.1.4.1.2011.5.25.1.5.1.2.1		not-accessible	Pots peer information.
INT hwVoPOTSPeerConfigIndex	1.3.6.1.4.1.2011.5.25.1.5.1.2.1.1	INTEGER	read-only	Index of voice pots peer table. It identify the number of the voice pots peer.
OCT hwVoPOTSPeerConfigPort	1.3.6.1.4.1.2011.5.25.1.5.1.2.1.4	OCTET STRING	read-write	set the voice port and group associated with this peer.The port number is seperated with group number by ':'.As analog voice port,the group number can be represented by 255.
OCT hwVoPOTSPeerConfigPrefix	1.3.6.1.4.1.2011.5.25.1.5.1.2.1.3	OCTET STRING	read-write	This object expresses the pattern to be added before the dialed number. Valid character include '0' to '9' and ','.
INT hwVoPOTSPeerConfigSendNumber	1.3.6.1.4.1.2011.5.25.1.5.1.2.1.5	INTEGER	read-write	This object specifies the number digits to send to the destination. It can take the value: 0-31 number of right-justified digits of the match-template to be sent. -1 Truncate the called number(default). -2 send all match-template digits.
hwVoPOTSPeerConfigTable	1.3.6.1.4.1.2011.5.25.1.5.1.2		not-accessible	The table contains the pots peer information .
hwVoVoIPPeerConfigEntry	1.3.6.1.4.1.2011.5.25.1.5.1.3.1		not-accessible	Voip peer information.
INT hwVoVoIPPeerConfigFastSwitch	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.4	INTEGER	read-write	This object expresses whether or not the fast connect function enable.
INT hwVoVoIPPeerConfigIndex	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.1	INTEGER	read-only	Index of voice voip peer table. It identify the number of the voip voice peer.
INT hwVoVoIPPeerConfigSendRing	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.7	INTEGER	read-write	enable/disable the send ring. It is valid only when fast connect is enabled .
IP hwVoVoIPPeerConfigSessionTarget	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.3	IpAddress	read-write	This object expresses the ip address IPV4 peer.
INT hwVoVoIPPeerConfigSessionTargetType	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.2	INTEGER	read-write	This object expresses the type of the session target for this peer .
hwVoVoIPPeerConfigTable	1.3.6.1.4.1.2011.5.25.1.5.1.3		not-accessible	The table contains the voip peer information.
OCT hwVoVoIPPeerConfigTeachPrefix	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.6	OCTET STRING	read-write	This object expresses the technology prefix. Valid charater include '0' to '9', '#'.
INT hwVoVoIPPeerConfigTunnelSwitch	1.3.6.1.4.1.2011.5.25.1.5.1.3.1.5	INTEGER	read-write	This object expresses whether or not the tunnel function enable. It cannot be used when no fast connect .

RFC description

Huawei vendor-private MIB for managing voice-over dial control, dial interfaces, and POTS (Plain Old Telephone Service) connectivity on their networking equipment.

Start monitoring Huawei voice gateway/integrated access device (dial-peer call routing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-VO-DIAL-CONTROL-MIB

What Is HUAWEI-VO-DIAL-CONTROL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description