All MIBs › HUAWEI-VO-DIGITAL-IF-MIB
Organization: Huawei-3COM Technologies Co., Ltd.
Last Updated: 2004-10-20
Category: Domain: Telephony/VoIP, Domain: VoIP/Telephony, Vendor: Huawei
Description: Huawei voice digital interface MIB for managing ISDN BRI/PRI and E1/T1 digital telephony port configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-VO-DIGITAL-IF-MIB?
HUAWEI-VO-DIGITAL-IF-MIB is a Huawei/Huawei-3Com vendor MIB that configures digital voice trunk interfaces on Quidway series routers - but its actual scope is channel-associated signaling (CAS), not ISDN BRI/PRI as the name might suggest. It's organized into a common port/timeslot-group configuration table (hwVoDigitalIfCommonCfgTable), an E&M signaling group (hwVoDigitalIfEMCfgTable, hwVoDigitalIfEMABCDCfgTable for ABCD signaling-bit behavior, hwVoDigitalIfEMTimerTable for signaling timers), and a much larger R2 (Compelled Signaling / MFC-R2) group, hwVoDigitalIfR2CfgTable, covering line/register signaling parameters such as billing category, calling-party category, digit collection, DTMF/MFC timers, ANI, and country-specific R2 variants, plus hwVoDigitalIfR2ABCDCfgTable for R2's own ABCD bit patterns. Because R2 and E&M are timeslot-oriented CAS protocols carried over E1/T1 digital trunks, this MIB is really about configuring per-timeslot-group signaling behavior on those trunks rather than ISDN Layer 2/3 call setup. It is deployed on Huawei/H3C digital voice gateway routers carrying legacy PBX/PSTN trunk traffic over E1/T1, and engineers standing up these gateways can look up the HUAWEI-VO-DIGITAL-IF-MIB download when configuring R2 or E&M trunk groups.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-VO-DIGITAL-IF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei/H3C Quidway series routers with digital voice trunk (E&M/R2) interface cards
Monitoring Examples
An operator reads hwVoDigitalIfR2CfgReqCallingCategory and hwVoDigitalIfR2CfgCongestion for a configured trunk group in hwVoDigitalIfR2CfgTable; calls failing to complete while the congestion object is set would point to R2 register signaling reporting network congestion rather than a dialing or ANI misconfiguration.
What Can Be Monitored
- common digital voice port/group configuration
- E&M ABCD signaling-bit configuration
- E&M signaling timer values
- R2 line/register signaling parameters (billing/calling category, ANI)
- R2 ABCD signaling-bit patterns
- R2 signaling timer configuration
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-3COM-OID-MIB
| voice | OBJECT-IDENTITY |
From SNMPv2-SMI
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwVoiceDigitalInterfaceMIB | 1.3.6.1.4.1.2011.5.25.1.4 | |||
| hwVoDigitalIfCommonObjects | 1.3.6.1.4.1.2011.5.25.1.4.1 | |||
| hwVoDigitalIfCommonCfgTable | 1.3.6.1.4.1.2011.5.25.1.4.1.1 | not-accessible | The voice digital interface common configuration table contains information about configuration parameters for digital voice interface. | |
| hwVoDigitalIfCommonCfgEntry | 1.3.6.1.4.1.2011.5.25.1.4.1.1.1 | not-accessible | An entry in the voice digital interface common configuration table. The entry is automatically created when a digital voice interface hardware is found. | |
| INT hwVoDigitalIfCfgPortNumber | 1.3.6.1.4.1.2011.5.25.1.4.1.1.1.1 | INTEGER | read-only | Index of voice digital interface common config table. It identify the number of the voice port. |
| INT hwVoDigitalIfCfgGroupNumber | 1.3.6.1.4.1.2011.5.25.1.4.1.1.1.2 | INTEGER | read-only | Index of voice digital interface common config table. It identify the number of the ds0 or pri group. |
| INT hwVoDigitalIfCfgBoardType | 1.3.6.1.4.1.2011.5.25.1.4.1.1.1.3 | INTEGER | read-only | This object expresses the type of digital voice interface. |
| INT hwVoDigitalIfCfgSignalType | 1.3.6.1.4.1.2011.5.25.1.4.1.1.1.4 | INTEGER | read-only | This object expresses the signal type of ds0 or pri group. |
| OCT hwVoDigitalIfCfgTimeSlotsConfigurable | 1.3.6.1.4.1.2011.5.25.1.4.1.1.1.5 | OCTET STRING | read-only | This object expresses whether the timeslot is available. '1' states the timeslot is available for the E1VI or T1VI, '0' states the timeslot is not available. For T1VI, the length is 24. For E1VI, the length is 32. |
| hwVoDigitalIfEMObjects | 1.3.6.1.4.1.2011.5.25.1.4.2 | |||
| hwVoDigitalIfEMCfgTable | 1.3.6.1.4.1.2011.5.25.1.4.2.1 | not-accessible | The voice digital interface e&m configuration table contains information about configuration parameters for digital e&m voice interface. | |
| hwVoDigitalIfEMCfgEntry | 1.3.6.1.4.1.2011.5.25.1.4.2.1.1 | not-accessible | An entry in the voice digital interface e&m configuration table. The entry is automatically created when a digital voice interface is configed for digital e&m signal. | |
| INT hwVoDigitalIfEMCfgPortNumber | 1.3.6.1.4.1.2011.5.25.1.4.2.1.1.1 | INTEGER | read-only | Index of voice digital interface e&m config table. It identify the number of the voice port. |
| INT hwVoDigitalIfEMCfgGroupNumber | 1.3.6.1.4.1.2011.5.25.1.4.2.1.1.2 | INTEGER | read-only | Index of voice digital interface e&m config table. It identify the number of the ds0 group. |
| INT hwVoDigitalIfEMCfgTimeoutInterDigits | 1.3.6.1.4.1.2011.5.25.1.4.2.1.1.3 | INTEGER | read-write | This object states the longest time to wait between two input digit from caller side. The default value is 10 seconds. |
| INT hwVoDigitalIfEMCfgTimeoutRinging | 1.3.6.1.4.1.2011.5.25.1.4.2.1.1.4 | INTEGER | read-write | This object expresses the ring timeout of the digital e&m interface. The value of 65535 indicates the timer is approach infinity. The default value of this object is 60 seconds. |
| INT hwVoDigitalIfEMCfgTimeoutWaitDigit | 1.3.6.1.4.1.2011.5.25.1.4.2.1.1.5 | INTEGER | read-write | This object expresses the wait digit timeout of the digital e&m interface. The value of 65535 indicates the timer is approach infinity. The default value of this object is 5 seconds. |
| hwVoDigitalIfEMABCDCfgTable | 1.3.6.1.4.1.2011.5.25.1.4.2.2 | not-accessible | The voice digital interface e&m abcd configuration table contains information about abcd bits configuration parameters for digital e&m voice interface. | |
| hwVoDigitalIfEMABCDCfgEntry | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1 | not-accessible | An entry in the voice digital interface e&m abcd configuration table. The entry is automatically created when a digital voice interface is configed for digital e&m signal. | |
| INT hwVoDigitalIfEMABCDCfgPortNumber | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1.1 | INTEGER | read-only | Index of voice digital interface e&m abcd config table. It identify the number of the voice port. |
| INT hwVoDigitalIfEMABCDCfgGroupNumber | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1.2 | INTEGER | read-only | Index of voice digital interface e&m abcd config table. It identify the number of the ds0 group. |
| OCT hwVoDigitalIfEMABCDRxIdle | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1.3 | OCTET STRING | read-write | This object expresses the a b c d bits for receiving idle signal. The default value is '1101'. |
| OCT hwVoDigitalIfEMABCDRxSeize | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1.4 | OCTET STRING | read-write | This object expresses the a b c d bits for receiving seize signal. The default value is '0101'. |
| OCT hwVoDigitalIfEMABCDTxIdle | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1.5 | OCTET STRING | read-write | This object expresses the a b c d bits for sending idle signal. The default value is '1101'. |
| OCT hwVoDigitalIfEMABCDTxSeize | 1.3.6.1.4.1.2011.5.25.1.4.2.2.1.6 | OCTET STRING | read-write | This object expresses the a b c d bits for sending seize signal. The default value is '0101'. |
| hwVoDigitalIfEMTimerTable | 1.3.6.1.4.1.2011.5.25.1.4.2.4 | not-accessible | The voice digital interface e&m timer table contains information about timer parameters for digital e&m voice interface. | |
| hwVoDigitalIfEMTimerEntry | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1 | not-accessible | An entry in the voice digital interface e&m timer table. The entry is automatically created when a digital voice interface is configed for digital e&m signal. | |
| INT hwVoDigitalIfEMTimerPortNumber | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.1 | INTEGER | read-only | Index of voice digital interface e&m timer config table. It identify the number of the voice port. |
| INT hwVoDigitalIfEMTimerGroupNumber | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.2 | INTEGER | read-only | Index of voice digital interface e&m timer config table. It identify the number of the ds0 group. |
| INT hwVoDigitalIfEMTimerCallInterval | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.3 | INTEGER | read-write | This object expresses the dureation of call clearing. The default value is 200 milliseconds. |
| INT hwVoDigitalIfEMTimerSendWink | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.4 | INTEGER | read-write | This object expresses the max time between receiving seizure signal and sending wink signal. The default value is 500 milliseconds. |
| INT hwVoDigitalIfEMTimerWinkRising | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.5 | INTEGER | read-write | This object expresses the max time between sending seizure signal and receiving wink signal. The default value is 1000 milliseconds. |
| INT hwVoDigitalIfEMTimerWinkHold | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.6 | INTEGER | read-write | This object expresses the max duration for sending wink signal. The default value is 500 milliseconds. |
| INT hwVoDigitalIfEMTimerDialoutDelay | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.7 | INTEGER | read-write | This object expresses max time sending called digits. The default value is 300 milliseconds. |
| INT hwVoDigitalIfEMTimerRising | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.8 | INTEGER | read-write | This object expresses the wait duration between receiveing seizure signal and sending delay signal. The default value is 300 milliseconds. |
| INT hwVoDigitalIfEMTimerHold | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.9 | INTEGER | read-write | This object expresses the max time sending delay signal. The default value is 400 milliseconds. |
| INT hwVoDigitalIfEMTimerDtmf | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.10 | INTEGER | read-write | This object expresses outgoing dtmf digit duration of the digital e&m interface. The default value is 120 milliseconds |
| INT hwVoDigitalIfEMTimerDtmfInterval | 1.3.6.1.4.1.2011.5.25.1.4.2.4.1.11 | INTEGER | read-write | This object expresses outgoing dtmf inter-digit duration of the digital e&m interface. The default value is 120 milliseconds |
| hwVoDigitalIfR2Objects | 1.3.6.1.4.1.2011.5.25.1.4.3 | |||
| hwVoDigitalIfR2CfgTable | 1.3.6.1.4.1.2011.5.25.1.4.3.1 | not-accessible | The voice digital interface r2 configuration table contains information about configuration parameters for digital r2 voice interface. | |
| hwVoDigitalIfR2CfgEntry | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1 | not-accessible | An entry in the voice digital interface r2 configuration table. The entry is automatically created when a digital voice interface is configed for digital r2 signal. | |
| INT hwVoDigitalIfR2CfgPortNumber | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.1 | INTEGER | read-only | Index of voice digital interface r2 config table. It identify the number of the voice port. |
| INT hwVoDigitalIfR2CfgGroupNumber | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.2 | INTEGER | read-only | Index of voice digital interface r2 config table. It identify the number of the ds0 group. |
| INT hwVoDigitalIfR2CfgAniSwitch | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.3 | INTEGER | read-only | This object expresses the ANI funtion is enable or disable. The default value is disable. |
| INT hwVoDigitalIfR2CallerDigits | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.4 | INTEGER | read-write | This object expresses how many digits will be collected befor sending A6. The default value of this object is 1. |
| INT hwVoDigitalIfR2DebounceTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.5 | INTEGER | read-write | This object expresses the minimus duration the line signal to persist. The default value of this object is 40. |
| INT hwVoDigitalIfR2Ka | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.6 | INTEGER | read-write | This object expresses the code of KA signal. The default value is 1. |
| INT hwVoDigitalIfR2Kd | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.7 | INTEGER | read-write | This object expresses the code of KD signal. The default value is 3. |
| INT hwVoDigitalIfR2SeizureAckTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.8 | INTEGER | read-write | This object expresses the longgest time to wait the seizure acknowldge signal. The default value is 1000 milliseconds. |
| INT hwVoDigitalIfR2SelectMode | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.9 | INTEGER | read-write | This object expresses the trunk mode to be selected. max set select trunk mode to max-mode maxpoll set select trunk mode to max-poll-mode min set select trunk mode to min-mode minpoll set select trunk mode to min-poll-mode The default value is min. |
| INT hwVoDigitalIfR2TimeoutKb | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.10 | INTEGER | read-write | This object expresses the maxinum time to wait kb signal. The default value of this object is 5000 milliseconds. |
| INT hwVoDigitalIfR2TimeoutKd | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.11 | INTEGER | read-write | This object expresses the maxinum time to wait kd signal. The default value of this object is 5000 milliseconds. |
| INT hwVoDigitalIfR2TimeoutNextNumber | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.12 | INTEGER | read-write | This object expresses the maxinum time to wait next number. The default value of this object is 5000 milliseconds. |
| INT hwVoDigitalIfR2TimeoutReleaseApprove | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.13 | INTEGER | read-write | This object expresses the maxinum time to wait release approve. The default value of this object is 1000 milliseconds. |
| I32 hwVoDigitalIfR2TimeoutRing | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.14 | Integer32 | read-write | This object expresses the maxinum time to wait the end of ring. The default value is 30000 milliseconds. |
| INT hwVoDigitalIfR2TimeoutSendAnswer | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.15 | INTEGER | read-write | This object expresses the maxinum time to wait Answer signal. The default value is 500 milliseconds. |
| INT hwVoDigitalIfR2CfgBillingCategory | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.16 | INTEGER | read-write | This object expresses the value of signal BillingCategory. The default value is 2. |
| INT hwVoDigitalIfR2CfgCallingCategory | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.17 | INTEGER | read-write | This object expresses the value of signal CallingCategory. The default value is 1. |
| INT hwVoDigitalIfR2CfgCongestion | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.18 | INTEGER | read-write | This object expresses the value of signal Congestion. The default value is 4. |
| INT hwVoDigitalIfR2CfgDemandRefused | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.19 | INTEGER | read-write | This object expresses the value of signal DemandRefused. The default value is 12. |
| INT hwVoDigitalIfR2CfgDigitEnd | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.20 | INTEGER | read-write | This object expresses the value of signal DigitEnd. The default value is 15. |
| INT hwVoDigitalIfR2CfgNullnum | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.21 | INTEGER | read-write | This object expresses the value of signal Nullnum. The default value is 5. |
| INT hwVoDigitalIfR2CfgReqBillingCategory | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.22 | INTEGER | read-write | This object expresses the value of signal requesting BillingCategory. The default value is 16. |
| INT hwVoDigitalIfR2CfgReqCallingCategory | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.23 | INTEGER | read-write | This object expresses the value of signal requesting CallingCategory. The default value is 5. |
| INT hwVoDigitalIfR2CfgReqCurrentdigit | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.24 | INTEGER | read-write | This object expresses the value of signal requesting Currentdigit. The default value is 16. |
| INT hwVoDigitalIfR2CfgReqFirstCallingnum | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.25 | INTEGER | read-write | This object expresses the value of signal requesting FirstCallingnum. The default value is 5. |
| INT hwVoDigitalIfR2CfgReqFirstDigit | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.26 | INTEGER | read-write | This object expresses the value of signal requesting FirstDigit. The default value is 16. |
| INT hwVoDigitalIfR2CfgReqNextCallednum | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.27 | INTEGER | read-write | This object expresses the value of signal requesting NextCallednum. The default value is 1. |
| INT hwVoDigitalIfR2CfgReqNextCallingnum | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.28 | INTEGER | read-write | This object expresses the value of signal requesting NextCallingnum. The default value is 5. |
| INT hwVoDigitalIfR2CfgReqLastFirstDigit | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.29 | INTEGER | read-write | This object expresses the value of signal requesting LastFirstDigit. The default value is 2. |
| INT hwVoDigitalIfR2CfgReqLastSecondDigit | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.30 | INTEGER | read-write | This object expresses the value of signal requesting LastSecondDigit. The default value is 7. |
| INT hwVoDigitalIfR2CfgReqLastThirdDigit | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.31 | INTEGER | read-write | This object expresses the value of signal requesting LastFirstDigit. The default value is 8. |
| INT hwVoDigitalIfR2CfgReqSwitchGroupB | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.32 | INTEGER | read-write | This object expresses the value of signal requesting SwitchGroupB. The default value is 3. |
| INT hwVoDigitalIfR2CfgSubscriberIdle | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.33 | INTEGER | read-write | This object expresses the value of signal SubscriberIdle. The default value is 6. |
| INT hwVoDigitalIfR2CfgSubscriberBusy | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.34 | INTEGER | read-write | This object expresses the value of signal SubscriberBusy. The default value is 3. |
| INT hwVoDigitalIfR2CfgDebounceTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.35 | INTEGER | read-write | This object expresses the minimus duration the line signal to persist. The default value of this object is 10. |
| INT hwVoDigitalIfR2CfgSendringBackTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.36 | INTEGER | read-write | This object expresses the minimus duration the back-ring to persist. The default value of this object is 60000. |
| INT hwVoDigitalIfR2CfgSendringBusyTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.37 | INTEGER | read-write | This object expresses the minimus duration the busy-ring to persist. The default value of this object is 30000. |
| INT hwVoDigitalIfR2CfgPulseSignalPersistenceTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.38 | INTEGER | read-write | This object expresses the value of PulseSignalPersistence-Timer. The default value is 150. |
| INT hwVoDigitalIfR2CfgDlAnswerTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.39 | INTEGER | read-write | This object expresses the value of Answer-Timer. The default value is 60000. |
| INT hwVoDigitalIfR2CfgDlClearBackTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.40 | INTEGER | read-write | This object expresses the value of ClearBack-Timer. The default value is 1000. |
| INT hwVoDigitalIfR2CfgDlClearForwardTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.41 | INTEGER | read-write | This object expresses the value of ClearForward-Timer. The default value is 1000. |
| INT hwVoDigitalIfR2CfgDlSeizureTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.42 | INTEGER | read-write | This object expresses the value of Seize-Timer. The default value is 1000. |
| INT hwVoDigitalIfR2CfgDlReanswerTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.43 | INTEGER | read-write | This object expresses the value of ReAnswer-Timer. The default value is 1000. |
| INT hwVoDigitalIfR2CfgDlReleaseGuardTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.44 | INTEGER | read-write | This object expresses the value of ReleaseGuard-Timer. The default value is 1000. |
| INT hwVoDigitalIfR2CfgMfcGroupBTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.45 | INTEGER | read-write | This object expresses the value of GroupB-Timer. The default value is 30000. |
| INT hwVoDigitalIfR2CfgAniEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.46 | INTEGER | read-write | This object expresses the ANI is enable or disable. The default value is disable. |
| INT hwVoDigitalIfR2CfgGroupBEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.47 | INTEGER | read-write | This object expresses the GroupB-Process is enable or disable . The default value is enable. |
| INT hwVoDigitalIfR2CfgClearForwardAckEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.48 | INTEGER | read-write | This object expresses the ClearForwardAck-Signal is enable or disable . The default value is disable. |
| INT hwVoDigitalIfR2CfgDlSeizureAckEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.49 | INTEGER | read-write | This object expresses the SeizureAck-Signal is enable or disable . The default value is enable. |
| INT hwVoDigitalIfR2CfgDTMFEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.50 | INTEGER | read-write | This object expresses the DTMF is enable or disable . The default value is disable. |
| INT hwVoDigitalIfR2CfgAnswerEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.51 | INTEGER | read-write | This object expresses the Answer-Signal is enable or disable . The default value is enable. |
| INT hwVoDigitalIfR2CfgReanswerEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.52 | INTEGER | read-write | This object expresses the ReAnswer-Signal is enable or disable . The default value is disable. |
| INT hwVoDigitalIfR2CfgFinalCallnumEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.53 | INTEGER | read-write | This object expresses the FinalCallnum-Signal is enable or disable . The default value is disable. |
| INT hwVoDigitalIfR2CfgForceMeteringEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.54 | INTEGER | read-write | This object expresses the Metering-Signal is enable or disable . The default value is disable. |
| INT hwVoDigitalIfR2CfgSendRingBackEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.55 | INTEGER | read-write | This object expresses the SendRingBack is enable or disable . The default value is enable. |
| INT hwVoDigitalIfR2CfgSendRingBusyEnable | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.56 | INTEGER | read-write | This object expresses the SendRingBusy is enable or disable . The default value is enable. |
| INT hwVoDigitalIfR2CfgReqCategoryOffset | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.57 | INTEGER | read-write | This object expresses the value of CategoryOffset . The default value is 1. |
| INT hwVoDigitalIfR2CfgReqCallingnumOffset | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.58 | INTEGER | read-write | This object expresses the value of CallingnumOffset . The default value is 1. |
| INT hwVoDigitalIfR2CfgCountryMode | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.59 | INTEGER | read-write | This object expresses the value of CountryMode . The default value is 9. |
| INT hwVoDigitalIfR2CfgSpecialCharacter | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.60 | INTEGER | read-write | This object expresses the SpecialCharacter(A,B,C,D,#,*). The default value is NULL. |
| INT hwVoDigitalIfR2CfgSpecialSignal | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.61 | INTEGER | read-write | This object expresses the signal of SpecialCharacter. The default value is 16. |
| INT hwVoDigitalIfR2CfgSelectMode | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.62 | INTEGER | read-write | This object expresses the trunk mode to be selected. max set select trunk mode to max-mode maxpoll set select trunk mode to max-poll-mode min set select trunk mode to min-mode minpoll set select trunk mode to min-poll-mode The default value is min. |
| INT hwVoDigitalIfR2CfgDTMFTime | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.63 | INTEGER | read-write | This object expresses the value of DTMF-Timer. The default value is 0. |
| INT hwVoDigitalIfR2CfgReqCallCreate | 1.3.6.1.4.1.2011.5.25.1.4.3.1.1.64 | INTEGER | read-write | This object expresses the value of signal callcreate in group-a. The default value is 6. |
| hwVoDigitalIfR2ABCDCfgTable | 1.3.6.1.4.1.2011.5.25.1.4.3.2 | not-accessible | The voice digital interface r2 abcd configuration table contains information about abcd bits configuration parameters for digital r2 voice interface. | |
| hwVoDigitalIfR2ABCDCfgEntry | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1 | not-accessible | An entry in the voice digital interface r2 abcd configuration table. The entry is automatically created when a digital voice interface is configed for digital r2 signal. | |
| INT hwVoDigitalIfR2ABCDCfgPortNumber | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.1 | INTEGER | read-only | Index of voice digital interface r2 abcd config table. It identify the number of the voice port. |
| INT hwVoDigitalIfR2ABCDCfgGroupNumber | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.2 | INTEGER | read-only | Index of voice digital interface r2 abcd config table. It identify the number of the ds0 group. |
| OCT hwVoDigitalIfR2ABCDReverseABCD | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.3 | OCTET STRING | read-write | This object expresses whether or not the a b c d bits should be invert. '0' : disable invert. '1' : enable invert. The default value is '0000'. |
| OCT hwVoDigitalIfR2ABCDRenewABCD | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.4 | OCTET STRING | read-write | This object expresses the unused a b c d bits to be sent. The default value is '1111'. |
| OCT hwVoDigitalIfR2ABCDRxIdle | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.5 | OCTET STRING | read-write | This object expresses the idle line signal bits to be received. The default value is '1001'. |
| OCT hwVoDigitalIfR2ABCDTxIdle | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.6 | OCTET STRING | read-write | This object expresses the idle line signal bits to be sent. The default value is '1001'. |
| OCT hwVoDigitalIfR2ABCDRxSeizure | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.7 | OCTET STRING | read-write | This object expresses the seizure line signal bits to be received. The default value is '0001'. |
| OCT hwVoDigitalIfR2ABCDTxSeizure | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.8 | OCTET STRING | read-write | This object expresses the seizure line signal bits to be sent. The default value is '0001'. |
| OCT hwVoDigitalIfR2ABCDRxSeizureAck | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.9 | OCTET STRING | read-write | This object expresses the seizureAck line signal bits to be received. The default value is '1101'. |
| OCT hwVoDigitalIfR2ABCDTxSeizureAck | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.10 | OCTET STRING | read-write | This object expresses the seizureAck line signal bits to be sent. The default value is '1101'. |
| OCT hwVoDigitalIfR2ABCDRxAnswer | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.11 | OCTET STRING | read-write | This object expresses the answer line signal bits to be received. The default value is '0101'. |
| OCT hwVoDigitalIfR2ABCDTxAnswer | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.12 | OCTET STRING | read-write | This object expresses the answer line signal bits to be sent. The default value is '0101'. |
| OCT hwVoDigitalIfR2ABCDRxClearForward | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.13 | OCTET STRING | read-write | This object expresses the ClearForward line signal bits to be received. The default value is '1001'. |
| OCT hwVoDigitalIfR2ABCDTxClearForward | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.14 | OCTET STRING | read-write | This object expresses the ClearForward line signal bits to be sent. The default value is '1001'. |
| OCT hwVoDigitalIfR2ABCDRxClearBack | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.15 | OCTET STRING | read-write | This object expresses the ClearBackward line signal bits to be received. The default value is '1101'. |
| OCT hwVoDigitalIfR2ABCDTxClearBack | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.16 | OCTET STRING | read-write | This object expresses the ClearBackward line signal bits to be sent. The default value is '1101'. |
| OCT hwVoDigitalIfR2ABCDRxReleaseGuard | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.17 | OCTET STRING | read-write | This object expresses the ReleaseGuard line signal bits to be received. The default value is '1001'. |
| OCT hwVoDigitalIfR2ABCDTxReleaseGuard | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.18 | OCTET STRING | read-write | This object expresses the ReleaseGuard line signal bits to be sent. The default value is '1001'. |
| OCT hwVoDigitalIfR2ABCDRxBlocking | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.19 | OCTET STRING | read-write | This object expresses the Blocking line signal bits to be received. The default value is '1101'. |
| OCT hwVoDigitalIfR2ABCDTxBlocking | 1.3.6.1.4.1.2011.5.25.1.4.3.2.1.20 | OCTET STRING | read-write | This object expresses the Blocking line signal bits to be sent. The default value is '1101'. |
RFC description
Huawei voice over IP digital interface management MIB for monitoring voice gateway digital port parameters and call-related statistics.
Start monitoring Huawei/H3C Quidway series router with digital voice trunk (E&M/R2) interfaces with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.