HUAWEI-CES-MIB

All MIBs › HUAWEI-CES-MIB

Organization: Huawei Technologies Co., Ltd.

Last Updated: 2011-02-09

Category: Pseudowire, Vendor: Huawei

Description: Huawei CES (Circuit Emulation Service) MIB for managing circuit emulation over packet networks including configuration and performance monitoring.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-CES-MIB?

HUAWEI-CES-MIB is Huawei's Circuit Emulation Service (CES) management MIB, used to configure and monitor circuit emulation of legacy TDM/E1/T1 circuits over Huawei packet-switched networks. It exposes NMS-facing objects for CES service configuration and, typically for this class of MIB, performance and alarm monitoring covering circuit synchronization, jitter-buffer status, and packet loss on the emulated circuit. Its monitoring relevance centers on service/software status and circuit-level fault detection: whether an emulated circuit is synchronized and error-free, since CES is used to carry latency-sensitive legacy traffic (such as voice trunks or leased-line replacement) over a packet core where jitter or loss directly degrades the emulated TDM signal. It typically works alongside standard interface and pseudowire/PWE3-related MIBs, since CES is one application of packet-based circuit emulation across an MPLS or Ethernet transport. It is deployed on Huawei packet-transport equipment in carrier networks replacing traditional TDM leased lines with packet-based emulation. Engineers can download the HUAWEI-CES-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-CES-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei packet-transport network equipment (CES-capable)

Monitoring Examples

No detailed sample objects were captured for this MIB, so specific table/object names cannot be confirmed; functionally, a carrier engineer would use a CES MIB of this type to check whether an emulated E1/T1 circuit remains synchronized and to monitor jitter-buffer underrun/overrun and packet-loss counters, since a rise in these would translate directly into audible/data errors on the emulated legacy circuit.

What Can Be Monitored

CES circuit synchronization status
jitter buffer status
packet loss on emulated circuit
CES service configuration

Imported Objects

From HUAWEI-DEVICE-MIB

hwConfigChangeIP
hwFrameIndex	OBJECT-TYPE
hwPortIndex	OBJECT-TYPE
hwSlotIndex	OBJECT-TYPE

From HUAWEI-MIB

huaweiMgmt

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwCes	1.3.6.1.4.1.2011.5.11			The MIB is used for defining Huawei's CES management MIB objects, which provides CES management NMS interfaces.
hwAtmCesServDescrExtTable	1.3.6.1.4.1.2011.5.11.1		not-accessible	CES service description extended table. This table is used during the creation of the connection between the CES-SDT port and the CES-V35 port. The index of this table is ifIndex.
hwAtmCesServDescrExtEntry	1.3.6.1.4.1.2011.5.11.1.1		not-accessible	CES service description extended table. This table is used during the creation of the connection between the CES-SDT port and the CES-V35 port. The index of this entry is ifIndex.
I32 hwAtmCesServDescrExtNValue	1.3.6.1.4.1.2011.5.11.1.1.1	Integer32	read-create	The N value of V35 port.
U32 hwAtmCesServDescrExtBitMap	1.3.6.1.4.1.2011.5.11.1.1.2	Unsigned32	read-create	The timeslot bitmap in SDT mode.
I32 hwAtmCesServDescrExtFillRate	1.3.6.1.4.1.2011.5.11.1.1.3	Integer32	read-create	The fillrate of cell.
ROW hwAtmCesServDescrExtRowStatus	1.3.6.1.4.1.2011.5.11.1.1.4	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. createAndGo(4),destroy(6)
hwAtmCesCfgTable	1.3.6.1.4.1.2011.5.11.2		not-accessible	CES board configration table. The indexes of this table are hwFrameIndex and hwSlotIndex.
hwAtmCesCfgEntry	1.3.6.1.4.1.2011.5.11.2.1		not-accessible	CES board configration table. The indexes of this entry are hwFrameIndex and hwSlotIndex.
INT hwAtmCesCfgWorkMode	1.3.6.1.4.1.2011.5.11.2.1.1	INTEGER	read-write	CES board working mode. Options: 1. tdm(1) - CES board working mode is tdm 2. e1(2) - CES board working mode is e1 3. v35(3) - CES board working mode is v35 4. idle(4) - CES board working mode is idle 5. indep(5) - CES board working mode is indep
INT hwAtmCesCfgDDNClockMode	1.3.6.1.4.1.2011.5.11.2.1.2	INTEGER	read-write	The DDN clock mode of CES board. Options: 1. line(1) - The DDN clock mode of CES board is line 2. srts(2) - The DDN clock mode of CES board is srts
I32 hwAtmCesCfgDDNClockSrcPort	1.3.6.1.4.1.2011.5.11.2.1.3	Integer32	read-write	The DDN clock source of CES board.
INT hwAtmCesCfgE1GroupType0	1.3.6.1.4.1.2011.5.11.2.1.4	INTEGER	read-write	E1 Group 0 (port 0~3) work mode. Options: 1. cesE1(1) - E1 work mode is cesE1 2. tdmE1(2) - E1 work mode is tdmE1 3. ddnE1(3) - E1 work mode is ddnE1
INT hwAtmCesCfgE1GroupType1	1.3.6.1.4.1.2011.5.11.2.1.5	INTEGER	read-write	E1 Group 1 (port 4~7) work mode. Options: 1. cesE1(1) - E1 work mode is cesE1 2. tdmE1(2) - E1 work mode is tdmE1 3. ddnE1(3) - E1 work mode is ddnE1
INT hwAtmCesCfgE1GroupType2	1.3.6.1.4.1.2011.5.11.2.1.6	INTEGER	read-write	E1 Group 2 (port 8~11) work mode. Options: 1. cesE1(1) - E1 work mode is cesE1 2. tdmE1(2) - E1 work mode is tdmE1 3. ddnE1(3) - E1 work mode is ddnE1
INT hwAtmCesCfgE1GroupType3	1.3.6.1.4.1.2011.5.11.2.1.7	INTEGER	read-write	E1 Group 3 (port 12~15) work mode. Options: 1. cesE1(1) - E1 work mode is cesE1 2. tdmE1(2) - E1 work mode is tdmE1 3. ddnE1(3) - E1 work mode is ddnE1
INT hwAtmCesCfgAccessMode	1.3.6.1.4.1.2011.5.11.2.1.8	INTEGER	read-write	Board work mode. Options: 1. e1(1) - E1 2. t1(2) - T1
hwAtmCesPortCfgTable	1.3.6.1.4.1.2011.5.11.3		not-accessible	Port configration table of CES board. The table is used to port configration of CES board. The index of this table is ifIndex.
hwAtmCesPortCfgEntry	1.3.6.1.4.1.2011.5.11.3.1		not-accessible	Port configration table of CES board. The table is used to port configration of CES board. The index of this entry is ifIndex.
INT hwAtmCesPortCfgWorkMode	1.3.6.1.4.1.2011.5.11.3.1.1	INTEGER	read-write	The working mode of port. Options: 1. uni(1) - UNI mode 2. sdt(2) - SDT mode 3. udt(3) - UDT mode 4. idle(4) - Idle mode 5. ima(5) - IMA mode 6. invalidMode(-1) - Invalid mode
INT hwAtmCesPortCfgClockMode	1.3.6.1.4.1.2011.5.11.3.1.2	INTEGER	read-write	The clock mode of port. Options: 1. system(1) - System clock 2. line(2) - Line clock 3. acm(3) - Acm clock 4. srts(4) - Srts clock 5. invalidClock(-1) - Invalid clock
INT hwAtmCesPortCfgSignalType	1.3.6.1.4.1.2011.5.11.3.1.3	INTEGER	read-write	Signal type of port. Options: 1. ccs(1) - CCS signal 2. cas(2) - CAS signal 3. invalidSignal(-1) - Invalid signal
INT hwAtmCesPortCfgFrameVerifyMode	1.3.6.1.4.1.2011.5.11.3.1.4	INTEGER	read-write	Frame verify mode of port. Options: 1. enable(1) - Open frame verify 2. disable(2) - Close frame verify 3. invalidOrNotSupport(-1) - Invalid or does not support frame verify
U32 hwAtmCesPortTimeSlotBMP	1.3.6.1.4.1.2011.5.11.3.1.5	Unsigned32	read-only	Timeslot bitmap of port, 0 is the initial value of timeslot bitmap.
U32 hwAtmCesPortCfgWarningStatus	1.3.6.1.4.1.2011.5.11.3.1.6	Unsigned32	read-only	Alarm state of port.
INT hwAtmCesPortCfgUtopiaStatus	1.3.6.1.4.1.2011.5.11.3.1.7	INTEGER	read-only	UTOPIA port state. Options: 1. normal(1) - Normal state 2. test(2) - Test state 3. idle(3) - Idle state 4. notExist(4) - Does not exist 5. fail(5) - Fail state 6. block(6) - Block state
INT hwAtmCesPortCfgLiuStatus	1.3.6.1.4.1.2011.5.11.3.1.8	INTEGER	read-only	LIU port state. Options: 1. normal(1) - Normal state 2. test(2) - Test state 3. idle(3) - Idle state 4. notExisted(4) - Does not exist 5. fail(5) - Fail state 6. block(6) - Block state 7. maintain(7) - Maintain state 8. localLoop(11) - Local-loop state 9. remoteLoop(12) - Remote-loop state 10. tsLocalLoop(13) - ts-Localloop state 11. payLoadLoop(14) - Payload-loop state 12. invalidStatus(-1) - Invalid state
INT hwAtmCesPortCfgImpedance	1.3.6.1.4.1.2011.5.11.3.1.9	INTEGER	read-write	Impedance of port. Options: 1. ohm75(1) - 75 ohm 2. ohm120(2) - 120 ohm 3. ohm100(3) - 100 ohm 4. invalidImpedance(-1) - Invalid impedance
INT hwAtmCesPortCfgPhyState	1.3.6.1.4.1.2011.5.11.3.1.10	INTEGER	read-only	E1 port physical state. Options: 1. normal(0) - Normal state 2. fault(1) - Fault state 3. unknown(2) - Unknown state
INT hwAtmCesPortCfgLoopLineState	1.3.6.1.4.1.2011.5.11.3.1.11	INTEGER	read-only	E1 port line state. Options: 1. synchronized(0) - Synchronized state 2. farEndAlarm(1) - Far-End-Alarm state 3. nearEndAlarm(2) - Near-End-Alarm state 4. testing(3) - Testing state 5. unknown(4) - Unknown state
INT hwAtmCesPortCfgE1Frametype	1.3.6.1.4.1.2011.5.11.3.1.12	INTEGER	read-write	pvm-e1 port frame type. Options: 1. pcm31(1) - PCM31 frame 2. unframe(2) - It's not a frame
INT hwAtmCesPortAdminStatus	1.3.6.1.4.1.2011.5.11.3.1.13	INTEGER	read-write	Port operation type. Options: 1. reset(1) - Reset port 2. selfcheck(2) - Self check
U32 hwAtmCesPCMErrorReportAlarm	1.3.6.1.4.1.2011.5.11.3.1.14	Unsigned32	read-only	PCM error report configuration. bit0: report alarm when pcm line fault occurs; bit1: set PCM fault and set port to OOS state when ULF exceeds the threshold; bit2: set PCM fault and set port to OOS state when OLF exceeds the threshold; bit3: report event when LDT exceeds the threshold; bit4: report event when frame slip exceeds the threshold; bit5: report event when line temporary disturb occurs.
I32 hwAtmCesPortCfgESAlarmThreshold	1.3.6.1.4.1.2011.5.11.3.1.15	Integer32	read-write	Errored seconds alarm threshold.
I32 hwAtmCesPortCfgCSESAlarmThreshold	1.3.6.1.4.1.2011.5.11.3.1.16	Integer32	read-write	Consecutive severely errored seconds alarm threshold.
I32 hwAtmCesPortCfgDMAlarmThreshold	1.3.6.1.4.1.2011.5.11.3.1.17	Integer32	read-write	Degraded minutes alarm threshold.
INT hwAtmCesPortLineCode	1.3.6.1.4.1.2011.5.11.3.1.18	INTEGER	read-write	Configuration of the line encoding type. Options: 1. hdb3(1) - HDB3 code 2. ami(2) - AMI code 3. b8zs(3) - B8ZS code 4. invalidCode(-1) - Invalid code
I32 hwAtmCesPortAcmSource	1.3.6.1.4.1.2011.5.11.3.1.19	Integer32	read-write	Configuration of adaptive clock source.
INT hwAtmCesPortCfgState	1.3.6.1.4.1.2011.5.11.3.1.20	INTEGER	read-only	Indicates the configuration status of the subscriber type. Options: 1. notConfigUserType(1) - Did not configure 2. configVoiceUserType(2) - Configured MG PRA subscriber 3. configPWUserType(3) - Configured Connection user 4. configNativeTDM(4) - Configured Native TDM
hwAtmCesPortV35CfgTable	1.3.6.1.4.1.2011.5.11.4		not-accessible	Port configration table of V35. This table is used to configure the CES-V35 port. The configuration includes reversing the clock and clock mode, blocking and unblocking the port, and querying the N value, status and alarm of the port. The index of this table is ifIndex.
hwAtmCesPortV35CfgEntry	1.3.6.1.4.1.2011.5.11.4.1		not-accessible	Port configration table of V35. This table is used to configure the CES-V35 port. The configuration includes reversing the clock and clock mode, blocking and unblocking the port, and querying the N value, status and alarm of the port. The index of this entry is ifIndex.
I32 hwAtmCesPortV35CfgNValue	1.3.6.1.4.1.2011.5.11.4.1.1	Integer32	read-only	N value of V35 port.
INT hwAtmCesPortV35CfgClockMode	1.3.6.1.4.1.2011.5.11.4.1.2	INTEGER	read-write	Clock mode of port. Options: 1. dceInternal(1) - Dec-Internal clock 2. dceSlave(2) - Dec-Slave clock 3. dceExternal(3) - Dec-External clock 4. dteInternal(4) - Dte-Internal clock 5. dteSlave(5) - Dte-Slave clock 6. dteExternal(6) - Dte-External clock
INT hwAtmCesPortV35CfgBlockStatus	1.3.6.1.4.1.2011.5.11.4.1.3	INTEGER	read-write	To block or unblock the port, or to inquiry the block state. Options: 1. block(1) - Block the port 2. unblock(2) - UnBlock the port 3. invalidStatus(-1) - Invalid status
INT hwAtmCesPortV35CfgReversePhase	1.3.6.1.4.1.2011.5.11.4.1.4	INTEGER	read-write	Inverse the clock of V35 port, inquiry the clock state. Options: 1. noInverse(1) - Not inverse state 2. inverse(2) - Inverse state
I32 hwAtmCesPortV35CfgWarningStatus	1.3.6.1.4.1.2011.5.11.4.1.5	Integer32	read-only	Alarm state of V35 port.
INT hwAtmCesPortV35CfgPortV35Status	1.3.6.1.4.1.2011.5.11.4.1.6	INTEGER	read-only	Port state of V35. Options: 1. idle(1) - Idle state 2. normal(2) - Normal state 3. localLoop(3) - Local loop state 4. remoteLoop(4) - Remote loop state 5. block(5) - Block state 6. fault(6) - Fault state
hwAtmCesChnlStatisTable	1.3.6.1.4.1.2011.5.11.5		not-accessible	The statistics table of CES channel. This table is used to collect the cell data of the SDT port. The index of this table is ifIndex.
hwAtmCesChnlStatisEntry	1.3.6.1.4.1.2011.5.11.5.1		not-accessible	The statistics table of CES channel. This table is used to collect the cell data of the SDT port. The index of this entry is ifIndex.
C32 hwAtmCesChnlStatisCounter0	1.3.6.1.4.1.2011.5.11.5.1.1	Counter32	read-only	Number of discarded cells due to Output Queue or Segmentation Buffer.
C32 hwAtmCesChnlStatisCounter1	1.3.6.1.4.1.2011.5.11.5.1.2	Counter32	read-only	Not used.
C32 hwAtmCesChnlStatisCounter2	1.3.6.1.4.1.2011.5.11.5.1.3	Counter32	read-only	Number of cells written to the Reassembly Buffer. It excludes cells that were discarded for any reason and cells that are inserted instead of lost cells (atmfReassembledCells).
C32 hwAtmCesChnlStatisCounter3	1.3.6.1.4.1.2011.5.11.5.1.4	Counter32	read-only	Number of times incomingMFB pulse is not synchronous to SDT start of structure upstream (AAL1).
C32 hwAtmCesChnlStatisCounter4	1.3.6.1.4.1.2011.5.11.5.1.5	Counter32	read-only	Number of cells causing a Reassembly Buffer overflow (AAL0 & AAL1). It includes accepted cells that are causing the filling level to exceed the predefined threshold and discarded cells due to the attempt of writing to the Reassembly Buffer when the threshold is already exceeded.
C32 hwAtmCesChnlStatisCounter5	1.3.6.1.4.1.2011.5.11.5.1.6	Counter32	read-only	Number of end of Reassembly Buffer overflow (AAL0 & AAL1). The value is incremented upon acceptance of the next cell after Reassembly Buffer overflow.
C32 hwAtmCesChnlStatisCounter6	1.3.6.1.4.1.2011.5.11.5.1.7	Counter32	read-only	The count of the number of AAL1 header errors detected including those corrected. Header errors include correctable and uncorrectable CRC, plus bad parity. (atmfCESHdrErrors).
C32 hwAtmCesChnlStatisCounter7	1.3.6.1.4.1.2011.5.11.5.1.8	Counter32	read-only	Number of times that the sequence number of an incoming AAL1 SARPDU causes a transition of the SC algorithm from 'sync' to 'out of sequence' and from 'invalid' to 'out of sync'.
C32 hwAtmCesChnlStatisCounter8	1.3.6.1.4.1.2011.5.11.5.1.9	Counter32	read-only	Number of downstream 'misinserted cells' detected by the AAL1 sequence count algorithm (atmfCESMisinsertedCells).
C32 hwAtmCesChnlStatisCounter9	1.3.6.1.4.1.2011.5.11.5.1.10	Counter32	read-only	Number of downstream cells discarded by the AAL1 sequence count algorithm.
C32 hwAtmCesChnlStatisCounter10	1.3.6.1.4.1.2011.5.11.5.1.11	Counter32	read-only	Number of rejected AAL1 SDT pointers due to parity error or wrong pointer value (93 < pointer <127).
C32 hwAtmCesChnlStatisCounter11	1.3.6.1.4.1.2011.5.11.5.1.12	Counter32	read-only	Number of SC cycles with more than one AAL1 SDT pointer field if only one pointer is expected (sdt_once = 1).
C32 hwAtmCesChnlStatisCounter12	1.3.6.1.4.1.2011.5.11.5.1.13	Counter32	read-only	Number of start of reassembly buffer underflow (AAL0 & AAL1) (atmfCESBufUnderflow).
C32 hwAtmCesChnlStatisCounter13	1.3.6.1.4.1.2011.5.11.5.1.14	Counter32	read-only	Number of inserted starvation cells (AAL0 & AAL1) due to reassembly buffer underflow.
C32 hwAtmCesChnlStatisCounter14	1.3.6.1.4.1.2011.5.11.5.1.15	Counter32	read-only	Number of times the Reassembly Buffer is re-initialized due to AAL1 start of structure is out of sync with port start of structure.This records the count of the number of events in which the AAL1 reassembler found that an SDT pointer is not where it is expected, and the pointer must be reacquired. This count is only meaningful for structured CES. (atmfCESPointerReframes).
C32 hwAtmCesChnlStatisCounter15	1.3.6.1.4.1.2011.5.11.5.1.16	Counter32	read-only	Number of downstream 'Lost cells' detected by the AAL1 sequence count algorithm (atmfCESLostCells).
INT hwAtmCesChnlStatisOper	1.3.6.1.4.1.2011.5.11.5.1.17	INTEGER	read-write	The operating code of clearing the statistics of CES SDT port. Options: 1. clear(1) - Clear the statistics of CES SDT port
hwAtmCesUDTPortStatisTable	1.3.6.1.4.1.2011.5.11.6		not-accessible	The statistics table of CES UDT port. This table is used to collect the cell data of the UDT port. The index of this table is ifIndex.
hwAtmCesUDTPortStatisEntry	1.3.6.1.4.1.2011.5.11.6.1		not-accessible	The statistics table of CES UDT port. This table is used to collect the cell data of the UDT port. The index of this entry is ifIndex.
C32 hwAtmCesUDTPortStatisCounter0	1.3.6.1.4.1.2011.5.11.6.1.1	Counter32	read-only	Number of discarded cells due to Output Queue or Segmentation Buffer.
C32 hwAtmCesUDTPortStatisCounter1	1.3.6.1.4.1.2011.5.11.6.1.2	Counter32	read-only	Not used.
C32 hwAtmCesUDTPortStatisCounter2	1.3.6.1.4.1.2011.5.11.6.1.3	Counter32	read-only	Number of cells written to the Reassembly Buffer. It excludes cells that were discarded for any reason and cells that are inserted instead of lost cells (atmfReassembledCells).
C32 hwAtmCesUDTPortStatisCounter3	1.3.6.1.4.1.2011.5.11.6.1.4	Counter32	read-only	Number of times incomingMFB pulse is not synchronous to SDT start of structure upstream (AAL1).
C32 hwAtmCesUDTPortStatisCounter4	1.3.6.1.4.1.2011.5.11.6.1.5	Counter32	read-only	Number of cells causing a Reassembly Buffer overflow (AAL0 & AAL1). It includes accepted cells that are causing the filling level to exceed the predefined threshold and discarded cells due to the attempt of writing to the Reassembly Buffer when the threshold is already exceeded.
C32 hwAtmCesUDTPortStatisCounter5	1.3.6.1.4.1.2011.5.11.6.1.6	Counter32	read-only	Number of end of Reassembly Buffer overflow (AAL0 & AAL1). The value is incremented upon acceptance of the next cell after Reassembly Buffer overflow.
C32 hwAtmCesUDTPortStatisCounter6	1.3.6.1.4.1.2011.5.11.6.1.7	Counter32	read-only	The count of the number of AAL1 header errors detected including those corrected. Header errors include correctable and uncorrectable CRC, plus bad parity. (atmfCESHdrErrors).
C32 hwAtmCesUDTPortStatisCounter7	1.3.6.1.4.1.2011.5.11.6.1.8	Counter32	read-only	Number of times that the sequence number of an incoming AAL1 SARPDU causes a transition of the SC algorithm from 'sync' to 'out of sequence' and from 'invalid' to 'out of sync'.
C32 hwAtmCesUDTPortStatisCounter8	1.3.6.1.4.1.2011.5.11.6.1.9	Counter32	read-only	Number of downstream 'misinserted cells' detected by the AAL1 sequence count algorithm (atmfCESMisinsertedCells).
C32 hwAtmCesUDTPortStatisCounter9	1.3.6.1.4.1.2011.5.11.6.1.10	Counter32	read-only	Number of downstream cells discarded by the AAL1 sequence count algorithm.
C32 hwAtmCesUDTPortStatisCounter10	1.3.6.1.4.1.2011.5.11.6.1.11	Counter32	read-only	Number of rejected AAL1 SDT pointers due to parity error or wrong pointer value (93 < pointer <127).
C32 hwAtmCesUDTPortStatisCounter11	1.3.6.1.4.1.2011.5.11.6.1.12	Counter32	read-only	Number of SC cycles with more than one AAL1 SDT pointer field if only one pointer is expected (sdt_once = 1).
C32 hwAtmCesUDTPortStatisCounter12	1.3.6.1.4.1.2011.5.11.6.1.13	Counter32	read-only	Number of start of reassembly buffer underflow (AAL0 & AAL1) (atmfCESBufUnderflow).
C32 hwAtmCesUDTPortStatisCounter13	1.3.6.1.4.1.2011.5.11.6.1.14	Counter32	read-only	Number of inserted starvation cells (AAL0 & AAL1) due to reassembly buffer underflow.
C32 hwAtmCesUDTPortStatisCounter14	1.3.6.1.4.1.2011.5.11.6.1.15	Counter32	read-only	Number of times the Reassembly Buffer is re-initialized due to AAL1 start of structure is out of sync with port start of structure.This records the count of the number of events in which the AAL1 reassembler found that an SDT pointer is not where it is expected, and the pointer must be reacquired. This count is only meaningful for structured CES. (atmfCESPointerReframes).
C32 hwAtmCesUDTPortStatisCounter15	1.3.6.1.4.1.2011.5.11.6.1.16	Counter32	read-only	Number of downstream 'lost cells' detected by the AAL1 sequence count algorithm (atmfCESLostCells).
INT hwAtmCesUDTPortStatisOper	1.3.6.1.4.1.2011.5.11.6.1.17	INTEGER	read-write	The operating code of clearing the statistics of CES UDT port. Options: 1. clear(1) - Clear the statistics of CES UDT port
hwAtmCesUNIPortStatisTable	1.3.6.1.4.1.2011.5.11.7		not-accessible	The statistics table of CES UNI port. This table is used to collect the cell data of the UNI port. The index of this table is ifIndex.
hwAtmCesUNIPortStatisEntry	1.3.6.1.4.1.2011.5.11.7.1		not-accessible	The statistics table of CES UNI port. This table is used to collect the cell data of the UNI port. The index of this entry is ifIndex.
C32 hwAtmCesUNIPortStatisCounter0	1.3.6.1.4.1.2011.5.11.7.1.1	Counter32	read-only	Number of discarded cells due to output queue, ATM Receive Buffer.
C32 hwAtmCesUNIPortStatisCounter1	1.3.6.1.4.1.2011.5.11.7.1.2	Counter32	read-only	Number of received cells with corrected HEC errors.
C32 hwAtmCesUNIPortStatisCounter2	1.3.6.1.4.1.2011.5.11.7.1.3	Counter32	read-only	Number of received cells with non-corrected HEC errors.
C32 hwAtmCesUNIPortStatisCounter3	1.3.6.1.4.1.2011.5.11.7.1.4	Counter32	read-only	Number of times cell delineation SYNC state is left, except when forced.
C32 hwAtmCesUNIPortStatisCounter4	1.3.6.1.4.1.2011.5.11.7.1.5	Counter32	read-only	Number of discarded cells due to ATM transmit buffer overflow.
INT hwAtmCesUNIPortStatisOper	1.3.6.1.4.1.2011.5.11.7.1.6	INTEGER	read-write	The operating code of clearing the statistics of CES UNI port. Options: 1. clear(1) - Clear the statistics of CES UNI port
hwAtmCesPortMaintTable	1.3.6.1.4.1.2011.5.11.8		not-accessible	The maintenace table of CES port. This table is used to set the loopback of the CES port, including the local loopback (LL), remote loopback (RL), and timeslot loopback. The timeslot loopback takes effect only on the CES-SDT port. The index of this table is ifIndex.
hwAtmCesPortMaintEntry	1.3.6.1.4.1.2011.5.11.8.1		not-accessible	The maintenace table of CES port. This table is used to set the loopback of the CES port, including the local loopback (LL), remote loopback (RL), and timeslot loopback. The timeslot loopback takes effect only on the CES-SDT port. The index of this entry is ifIndex.
INT hwAtmCesPortMaintLoop	1.3.6.1.4.1.2011.5.11.8.1.1	INTEGER	read-write	The looping test mode of CES port. Options: 1. noLoop(1) - No-loop test 2. localLoop(2) - Local-loop test 3. remoteLoop(3) - Remote-loop test 4. tsLocalLoop(4) - Ts-Localloop test 5. payLoadLoop(5) - Payload-loop test
INT hwAtmCesPortMaintOper	1.3.6.1.4.1.2011.5.11.8.1.2	INTEGER	read-write	The oprating of looping test mode. Options: 1. set(1) - Set looping test 2. clear(2) - Clear looping test 3. notSupportQuery(-1) - Not support query
I32 hwAtmCesPortMaintSingleTimeslotId	1.3.6.1.4.1.2011.5.11.8.1.3	Integer32	read-write	The timeslot number of single timeslot looping test.
hwCesECSMonitorControlTable	1.3.6.1.4.1.2011.5.11.11		not-accessible	E1 monitor status control table. The indexes of this table are ifIndex and hwCesECSMonitorPeriodType.
hwCesECSMonitorControlEntry	1.3.6.1.4.1.2011.5.11.11.1		not-accessible	E1 monitor status control table. The indexes of this entry are ifIndex and hwCesECSMonitorPeriodType.
INT hwCesECSMonitorPeriodType	1.3.6.1.4.1.2011.5.11.11.1.1	INTEGER	read-write	Monitor period type. Options: 1. quarter(1) - Quarter 2. day(2) - Day
INT hwCesECSMonitorStatusReal	1.3.6.1.4.1.2011.5.11.11.1.2	INTEGER	read-only	Current monitor status, 0:disable, 1:enable. Options: 1. disable(0) - Disable current monitor 2. enable(1) - Enable current monitor
DAT hwCesECSMonitorStartTimeReal	1.3.6.1.4.1.2011.5.11.11.1.3	DateAndTime	read-only	The start time of the monitor.
INT hwCesECSMonitorStatusUserSet	1.3.6.1.4.1.2011.5.11.11.1.4	INTEGER	read-write	The monitor status set by user. Options: 1. disable(0) - Set monitor close 2. enable(1) - Set monitor open
DAT hwCesECSMonitorStartTimeUserSet	1.3.6.1.4.1.2011.5.11.11.1.5	DateAndTime	read-write	The start time of the monitor set by user.
hwCesECSThresholdControlTable	1.3.6.1.4.1.2011.5.11.12		not-accessible	E1 threshold enable table. The indexes of this table are ifIndex and hwCesECSMonitorPeriodType.
hwCesECSThresholdControlEntry	1.3.6.1.4.1.2011.5.11.12.1		not-accessible	E1 threshold enable table. The indexes of this entry are ifIndex and hwCesECSMonitorPeriodType.
INT hwCesECSThresholdEnabled	1.3.6.1.4.1.2011.5.11.12.1.1	INTEGER	read-write	E1 threshold enable. Options: 1. disable(0) - Disable the E1 threshold 2. enable(1) - Enable the E1 threshold
hwCesECSThresholdTable	1.3.6.1.4.1.2011.5.11.13		not-accessible	E1 monitor threshold table. The indexes of this table are ifIndex and hwCesECSMonitorPeriodType.
hwCesECSThresholdEntry	1.3.6.1.4.1.2011.5.11.13.1		not-accessible	E1 monitor threshold table. The indexes of this entry are ifIndex and hwCesECSMonitorPeriodType.
G32 hwCesECSThresholdLowES	1.3.6.1.4.1.2011.5.11.13.1.1	Gauge32	read-write	Errored seconds low threshold.
G32 hwCesECSThresholdHighES	1.3.6.1.4.1.2011.5.11.13.1.2	Gauge32	read-write	Errored seconds high threshold.
G32 hwCesECSThresholdSES	1.3.6.1.4.1.2011.5.11.13.1.3	Gauge32	read-write	Severely errored seconds threshold.
G32 hwCesECSThresholdUAS	1.3.6.1.4.1.2011.5.11.13.1.4	Gauge32	read-write	Unavailable seconds threshold.
G32 hwCesECSThresholdCESC	1.3.6.1.4.1.2011.5.11.13.1.5	Gauge32	read-write	Consecutive severely errored seconds threshold.
hwCesECSDateTable	1.3.6.1.4.1.2011.5.11.14		not-accessible	E1 perform monitor statistic table. The indexes of this table are ifIndex, hwCesECSMonitorPeriodType and hwCesECSMonitorStage.
hwCesECSDateEntry	1.3.6.1.4.1.2011.5.11.14.1		not-accessible	E1 perform monitor statistic table. The indexes of this entry are ifIndex, hwCesECSMonitorPeriodType and hwCesECSMonitorStage.
INT hwCesECSMonitorStage	1.3.6.1.4.1.2011.5.11.14.1.1	INTEGER	read-only	Perform monitor period stage, 0:current, 1:history Options: 1. current(0) - The perform monitor period is current 2. history(1) - The perform monitor period is history
DAT hwCesECSMonitorStageStartTime	1.3.6.1.4.1.2011.5.11.14.1.2	DateAndTime	read-only	The start time of the monitor period.
G32 hwCesECSDataES	1.3.6.1.4.1.2011.5.11.14.1.3	Gauge32	read-only	Statistic of the errored seconds.
G32 hwCesECSDataSES	1.3.6.1.4.1.2011.5.11.14.1.4	Gauge32	read-only	Statistic of the severe errors.
G32 hwCesECSDataUAS	1.3.6.1.4.1.2011.5.11.14.1.5	Gauge32	read-only	Statistic of the unavailable seconds.
hwAtmCesSubboardWorkModeTable	1.3.6.1.4.1.2011.5.11.15		not-accessible	CES board configration table. The indexes of this table are hwFrameIndex and hwSlotIndex.
hwAtmCesSubboardWorkModeEntry	1.3.6.1.4.1.2011.5.11.15.1		not-accessible	CES board configration table. The indexes of this entry are hwFrameIndex and hwSlotIndex.
INT hwAtmCesSubboardWorkMode	1.3.6.1.4.1.2011.5.11.15.1.1	INTEGER	read-write	CES subboard working mode. Options: 1. loadsharing(1) - The CES subboard works in loadsharing mode 2. activestandby(2) - The CES subboard works in activestandby mode
hwCesECSThresholdParameterTable	1.3.6.1.4.1.2011.5.11.16
I32 hwCesErroredSeconds	1.3.6.1.4.1.2011.5.11.16.1	Integer32	read-write	Errored seconds degrade threshold.
I32 hwCesConsecutiveSeverelyErroredSeconds	1.3.6.1.4.1.2011.5.11.16.2	Integer32	read-write	Consecutive severely errored seconds degrade threshold.
I32 hwCesDegradedMinutes	1.3.6.1.4.1.2011.5.11.16.3	Integer32	read-write	Degraded Minutes degrade threshold.
I32 hwCesPortUnconditionalLineFailureErroredRate	1.3.6.1.4.1.2011.5.11.16.4	Integer32	read-write	Line Unconditional Blooey Errored Rate threshold.
I32 hwCesPortOptionalLineFailureErroredRate	1.3.6.1.4.1.2011.5.11.16.5	Integer32	read-write	Line Conditional Blooey Errored Rate threshold.
I32 hwCesPortLineDisturbanceTransientErroredRate	1.3.6.1.4.1.2011.5.11.16.6	Integer32	read-write	Line Temporary Disturb Errored Rate threshold.
I32 hwCesPortG704ExcessiveFrameSlipfrequency	1.3.6.1.4.1.2011.5.11.16.7	Integer32	read-write	Overfull Frame Slip threshold.
I32 hwCesDefinedErroredSeconds	1.3.6.1.4.1.2011.5.11.16.8	Integer32	read-write	Errored Seconds Define threshold.
I32 hwCesDefinedSeverelyErroredSeconds	1.3.6.1.4.1.2011.5.11.16.9	Integer32	read-write	Severely Errored Seconds Define threshold.
I32 hwCesDefinedDegradedMinutes	1.3.6.1.4.1.2011.5.11.16.10	Integer32	read-write	Degraded Minutes Define threshold.
hwAtmCesPortCESoPCLKTable	1.3.6.1.4.1.2011.5.11.17		not-accessible	Adaptive clock source configuration table. The indexes of this table are hwFrameIndex, hwSlotIndex and hwAtmCesPortCESoPCLKIndex.
hwAtmCesPortCESoPCLKEntry	1.3.6.1.4.1.2011.5.11.17.1		not-accessible	Adaptive clock source configuration table. The indexes of this entry are hwFrameIndex, hwSlotIndex and hwAtmCesPortCESoPCLKIndex.
I32 hwAtmCesPortCESoPCLKIndex	1.3.6.1.4.1.2011.5.11.17.1.1	Integer32	not-accessible	The index of adaptive clock source.
U32 hwAtmCesPortCESoPCLKBindPW	1.3.6.1.4.1.2011.5.11.17.1.2	Unsigned32	read-write	Set and get the Connection ID binding with the adaptive clock source.
INT hwAtmCesPortCESoPCLKSetFlag	1.3.6.1.4.1.2011.5.11.17.1.3	INTEGER	read-write	Get and set the configuration of adaptive clock source. Options: 1. null(1) - The clock source is null 2. exist(2) - The clock source exist
INT hwAtmCesPortCESoPCLKState	1.3.6.1.4.1.2011.5.11.17.1.4	INTEGER	read-only	Get the running state of adaptive clock source. Options: 1. normal(1) - Normal state 2. fault(2) - Fault state
I32 hwAtmCesPortCESoPLineCLKPortId	1.3.6.1.4.1.2011.5.11.17.1.5	Integer32	read-write	Set and get the Port ID binding with the Line clock source.
INT hwAtmCesPortCESoPLineCLKState	1.3.6.1.4.1.2011.5.11.17.1.6	INTEGER	read-only	Get the running state of Line clock source. Options: 1. normal(1) - Normal state 2. fault(2) - Fault state
hwCesTDMVCLCfgTable	1.3.6.1.4.1.2011.5.11.18		not-accessible	TDM VCL configuration table. The indexes of this table are hwTDMVCLID and ifIndex.
hwCesTDMVCLCfgEntry	1.3.6.1.4.1.2011.5.11.18.1		not-accessible	TDM VCL configuration table. The indexes of this entry are hwTDMVCLID and ifIndex.
U32 hwTDMVCLID	1.3.6.1.4.1.2011.5.11.18.1.1	Unsigned32	not-accessible	TDM VCL ID.
INT hwTDMVCLType	1.3.6.1.4.1.2011.5.11.18.1.2	INTEGER	read-write	TDM VCL type. Options: 1. satop(1) - The TDM VCL Type is satop 2. cesop(2) - The TDM VCL Type is cesop
U32 hwTDMVCLTimeslot	1.3.6.1.4.1.2011.5.11.18.1.3	Unsigned32	read-write	TDM timeslot, it must be set if hwTDMVCLType is set to be cesop.
ROW hwTDMVCLRowStatus	1.3.6.1.4.1.2011.5.11.18.1.4	RowStatus	read-write	Row operation node . Running status cannot be deleted.
hwCesTrapsVbOids	1.3.6.1.4.1.2011.5.11.19
INT hwAtmCesPortStatus	1.3.6.1.4.1.2011.5.11.19.1	INTEGER	accessible-for-notify	Indicate the port state. Options: 1. normal(1) - The port is in normal state 2. test(2) - The port is in test state 3. idle(3) - The port is in idle state 4. notExisted(4) - The port doesn't exist 5. fail(5) - The port is in fail state 6. block(6) - The port is in block state 7. maintain(7) - The port is in maintain state 8. loopback(11) - The port is in loopback state
hwCesTraps	1.3.6.1.4.1.2011.5.11.20
hwCesCommonTraps	1.3.6.1.4.1.2011.5.11.20.1
hwCesCommonTrapsPrefix	1.3.6.1.4.1.2011.5.11.20.1.0
NTF hwCesPortStatusTrap	1.3.6.1.4.1.2011.5.11.20.1.0.1			This trap message is generated when Ces port status changed.
NTF hwCesBoardWorkModeChangeTrap	1.3.6.1.4.1.2011.5.11.20.1.0.2			This trap message is generated when E1T1 board work mode changed.
NTF hwCesPortWorkModeChangeTrap	1.3.6.1.4.1.2011.5.11.20.1.0.3			This trap message is generated when Ces port work mode changed.
hwCesAlarmTraps	1.3.6.1.4.1.2011.5.11.20.2
hwCesAlarmTrapsPrefix	1.3.6.1.4.1.2011.5.11.20.2.0
NTF hwCesPortSignalLossAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.1			This trap message is generated when Loss of signal occurs at the E1/T1 port.
NTF hwCesFrameLossAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.2			This trap message is generated when Loss of frame alignment occurs at the E1/T1 port.
NTF hwCesRemoteAlarmReceivedAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.3			This trap message is generated when remote alarm occurs at the E1/T1 port.
NTF hwCesMultiframeLossAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.4			This trap message is generated when Loss of multiframe alignment occurs at the E1/T1 port.
NTF hwCesSignalOccurAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.5			This trap message is generated when signal occurs at the E1/T1 port.
NTF hwCesCRC4ErrorOccurAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.6			This trap message is generated when CRC4 error occurs at the E1/T1 port.
NTF hwCesLOSRecoverAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.7			This trap message is generated when Loss of signal(LOS) recover at the E1/T1 port.
NTF hwCesFrameRecoverAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.8			This trap message is generated when Loss of frame recover at the E1/T1 port.
NTF hwCesRemoteAlarmRecoverAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.9			This trap message is generated when Remote alarm recover at the E1/T1 port.
NTF hwCesMultiframeRecoverAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.10			This trap message is generated when Loss of multiframe alignment recover at the E1/T1 port.
NTF hwCesSignalRecoverAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.11			This trap message is generated when signal recover at the E1/T1 port.
NTF hwCesCRC4RecoverAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.12			This trap message is generated when CRC4 recover at the E1/T1 port.
NTF hwCesACMClockRestoreAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.13			This trap message is generated when ACM clock restore.
NTF hwCesACMClockFaultAlarmTrap	1.3.6.1.4.1.2011.5.11.20.2.0.14			This trap message is generated when ACM clock fault.

RFC description

Huawei Circuit Emulation Services (CES) management MIB for ATM-based circuit emulation port configuration and monitoring.

Start monitoring Huawei packet-transport network equipment (Circuit Emulation Service) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-CES-MIB

What Is HUAWEI-CES-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description